Register / log-in to add to your Hammerwall Collection.
Manual Location
The Search Results for the Search Section to the left will appear here.
Page: 1
Earthquake Models 8900,8902,9000,9200 Model 8902 Model 9200 Model 9000 Model 8900 Owner's Manual Manufactured by ARDISAM , INC . CALIFORNIA PROPOSITION 65 WARNING 1360 1st Avenue ; RO . Box666 Engine exhaust from this product contains Cumberland , Wisconsin 54829 chemicals known to the State of California to ( 715 ) 822 - 2415 Fax ( 715 ) 822 - 4180 cause cancer , birth defects , or other 1 - 800 - 3456 - 007 reproductive harm . www . ardisam . com
Page: 2
V INTRODUCTION Congratulations ! You have just purchased the best Power Earth Auger money can buy . Please read the Jbllowing operating and safety instructions . Byjbllowing these instructions , this " unit will give you many years & " dependable and carefree service . The Earthquake ® Model 8900 Earth Augerj _ ature a 2HP , 49cc Tecumseh ( TC300 ) engine . The Earthquake ® Model 9000 Earth Auger feature a 3HP , , 85cc Teeumseh ( AV520 ) engine . These units " are designed _ br one - person use when drilling holes ' in ice and one or two person ( s ) use when used as an earth auger All parts and workmanship & " the gear ease and auger are warranted by the manu _ bcturer A copy of this warranty is " located on the back of this manual . The engine is ' covered by a separate engine manufacturer's warranty . The manual and warranty _ br each engine noted above is ' also enclosed . Please read the GENERAL OPERATING INSTRUCTIONS and SAFETY PRECAUTIONS noted below be _ bre operating this " unit . GENERAL OPERATING INSTRUCTIONS L The gear case has 4 ounces of grease installed at the factory . It is recommended that once a year the gear case be split and the grease level checked . Add grease only if level of grease is below top of the gears , DO NOT OVERFILL . Z Attach auger to powerhead with bolt provided , 3 , Read engine operating manual and follow instructions for fuel type , starting , etc . BE SURE TO USE PROPER GAS / OIL MIXTURE . 4 . The clutch will transfer maximum power after about two hours of normal operation . During this break - in period clutch slippage may occur , The clutch should be kept free ofoil or other moisture for efficient operation . Each unit is tested at the factory , but is not operated for the full break - in period . 5 . Dig holes without placing excessive body weight on the unit . The auger operates most efficiently with a shaving action caused by the weight of the unit itself . 6 . Do not use an ice auger in earth or an earth auger in ice . You may use the same powerhead , but a different style auger is required for each application . 7 . When digging in heavy soil , pump the unit with an up and down motion in the hole for every one foot of depth . 8 . Do not operate unit in excessively rocky ground . The unit functions well in ground where the rocks do not exceed the size of a persons fist . 9 . The ice auger blade protector should be attached to the auger head when not is use . This will protect the cutting edges of the ice auger blades . 10 . For cold weather operation , store the unit in a cool environment . Transferring the unit from a warm to a cold place can cause the buildup of harmful condensation . SAFETY PRECAUTIONS Read and follow all instructions in this manual and any others provided with this equipment . This symbol points out important safety instructions which if not followed could endanger your personal safety . Ice blades are very sharp . Use extreme caution , & Do not allow children to operate this power auger . when drilling a hole or replacing the blades . Make sure all first time users have been properly instructed . Do not carry the powerhead / auger between holes & Keep all screws , nuts and bolts tight . with the engine running . & The auger should not rotate when the engine is Close gas tank cap air vent when engine is stopped . , & idling . If it does rotate when engine is idling contact , & the place of purchase for instructions . Do not tilt gas tank indoors or when engine is , & running or is hot . Always keep hands and feet clear of rotating auger . Do not wear loose clothing while operating the power auger . Engine should be shut off before any repairs are attempted .
Page: 3
ESKIMO / EARTHQUAKE MODEL 9000 Part # Description 60G56 NUT - Hex , 5 / 16 " - 18 , two way reversible locknut 903 DECAL , Eskimo 903E DECAL , Earthquake 1402 BOLT - SHCS , 5 / 16 " - 18 x 1 - 1 / 4 " , ( mount ring to engine ) 1423 BOLT - HHCS , 5 / 16 " - 18 x 2 " , Grade 5 , ( auger shock spring ) 1433 BOLT - Hex Hd , 3 / 8 " - 16 x 1 - 1 / 2 " , ( earth auger to powerhead ) 2104 NUT - Hex , 3 / 8 " - 16 , Locking 8651 STRAP , Blade Protector 8955 8912 44T GEAR 8913 SHAFT , Output , 7 / 8 " DOWEL PIN , 1 / 4 " x 112 " , Hm'dened Steel 8915 8919 GASKET - _ 9010 II BALL BEARING 8922 8923 BALL BEARING _ 9037 _ NAP RING 8924 8929 BOLT - SHCS , 1 / 4 " - 20 x 1 - 1 / 2 " ( gear case bottom to gear case top ) QTSN , II _ _ 1402 ( 4 places ) 8931 BOLT - SHCS , 1 / 4 " - 20 x 2 " QT8N , i _ - \ _ 9020B Ii ( gear case to handleEar plate ) QTION 9020 8939 GEAR CASE , ( lower hall ) 8955 AUGER BOLT - SHCS , 3 / 8 " - 16 x 1 - 1 / 4 " , QB6 , QB8 , _ a _ \ _ _ / ( ice auger to powerhead ) QB10 _ J _ 9020A 8957 POINT , Ice IB5816 8958 POINT , Earth 8958HD POINT , Fishtail @ _ 9016 8980 EARTH AUGER SPRING , ( 6 " - 10 " only ) 9005 THROTTLE CONTROL ROD _ 9017 THROTTLE CONTROL TWIST 9005A 9010 HANDLEBAR - l Person _ < _ 8922 1N58 CLUTCH DRUM 3 " Threaded 9016 8957 9017 12T PINION GEAR 9020 CENTRIFUGAL CLUTCH ROTOR 2104 1433 9o38 9020A CENTRIFUGAL CLUTCH SPRING / / 9020B CENTRIFUGAL CLUTCH SHOES II _ < - _ 8924 / 8919 9037 MOUNT RING , ( handlebar to gear case top ) I I i 8980 9038 GEAR CASE , ( upper lmlD 8923 10T PINION GEAR 9214A GASENGINE AV520 EARTH AUGER EA2F 2 " , w / fishtail point I _ 8924 C - i 8924 EARTH AUGER 3 " , w / fishtail point EA3F I I I ! F _ A2F , EAaF , EA4F , EARTH AUGER 4 " , w / fishtail point EA4F i 8915 EARTH AUGER EA6F 6 " , w / fishtail point EA6F , EA8F , 8 ° 15 EARTH AUGER 8 " , w / fishtail point EAgF C EA10F EAIOF EARTH AUGER 10 " , w / fishtail point j EBOLT EB4 BLADE , Emth , 4 " rl ; 8912 EB6 BLADE , Emth , 6 " I EB4 , EB8 BLADE , Emth , 8 " EB6 , EBI0 BLADE , Ealth , I0 " ( _ _ < _ EB8 , _ _ 9214A EBOLT BOLT , Hex , I / 4 " - 28 x 5 / 8 " _ _ / EB10 ENUT NUT , NyD . ck , U4 " - 28 , / eai _ h blade tQ auger ) r _ 8923 GCA GAS CAP - _ ENUT I 8939 GT3HP GAS TANK IB5816 BOLT , 5ram x 0.8 x 16nmh ( ice blade to auger ) | _ 8929 ( 2 places ) 8958 ( _ 8958HD IN58 NUT , 5ram x 0.8 Nylock , ( ice blade to auger ) 8922 BLADE PROTECTOR , Ice , 8 " PBP8A PBPIOA BLADE PROTECTOR , Ice , 10 " _ 8931 ( 4 places ) BLADE , Ice , 6 " QB6 BLADE , Ice , 8 " QB8 QBI0 BLADE , Ice , 10 " _ 8851 _ , € - _ 8913 ICE AUGER , 6 " QT6N QT8N ICE AUGER , 8 " ICE AUGER , I0 " QTION WF516 WASHER - FLAT , 5 / 16 " , ( auger shock spring ) 3
Page: 4
V ESKIMO / EARTHQUAKE MODEL 8900 & EQ8902 GT49B . _ _ GCA I I _ _ - _ - - _ [ _ < - - _ 9 03 E _ _ _ . . . . . - - _ 893 8900 Only 89051 8910T 8902 Only 1501 / 4
Page: 5
O Eskimo / Earthquake Model 8900 & Earthquake Model 8902 Parts List MINIMUM ORDER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $ 10.00 Part # Description Qty . Part # Description Qty . 1 60G56 NUT - Hex , 5 / 16 " - 18 , two way reversible locknut 2 8939 GEAR CASE , ( lower half ) 60G70 TOGGLE SWITCH 1 1 8955 AUGER BOLT - SHCS , 3 / 8 " - 16 x 1 - 1 / 4 " , ( auger to pwrhead ) 1 719 LOCKWASHER - Spring , 3 / 8 " 1 8957 POINT , Ice 1 893 DECAL , Eskimo 1 8958 POINT , Emth 1 903E DECAL , Earthquake 1 8958HD POINT , Fishtail 1 928A SHOULDER NUT , 5 / 16 " - 18 1 8980 EARTH AUGER SPRING , ( 6 " - 10 " only ) 2 9205B THROTTLE FINGER TIP CONTROL 1 1423 BOLT - HHCS , 5 / 16 " - 18 x 2 " , Grade 5 , ( auger shock spring ) 4 1433 BOLT - Hex Hd , 3 / 8 " - 16 x 1 - 1 / 2 " , ( earth auger to pwrhead ) 1 9211 HANDLE GRIP , 7 / 8 " ] D 1 1501 BOLT - Hex Hd , 5 / 16 " - 18 x 3 / 4 " , Grade 5 , Zinc 1 9214 48T GEAR & 10T PINION GEAR , one piece unit , emth 1 2104 NUT - Hex , 3 / 8 " - 16 , Locking 1 EA2F EARTH AUGER , 2 " , w / fishtail point 8651 STRAP , Blade Protector 1 1 EA3F EARTH AUGER , 3 " , w / fishtail point 1 89025C THROTTLE CONTROL ROD , 8902 1 EA4F EARTH AUGER , 4 " , w / fishtail point 1 89051 THROTTLE CONTROL ROD , 8900 1 EA6F EARTH AUGER , 6 " , w / fishtail point 1 8910T HANDLEBAR - I Person , w / throttle mounting tab 1 EA8F EARTH AUGER , 8 " , w / fishtail point 1 8911 48T GEAR & 12T PINION GEAR , one piece unit , ice 1 EAIOF EARTH AUGER , 10 " , w / fishtail point 8912 44T GEAR 1 1 EB4 BLADE , Earth , 4 " 1 8913 SHAFT , Output , 7 / 8 " 1 EB6 BLADE , Earth , 6 " 8915 DOWEL PIN , 1 / 4 " x 1 / 2 " , Hardened Steel 1 1 EB8 BLADE , Earth , 8 " 8916 CLUTCH DRUM & 7T PINION GEAR 1 1 EB10 BLADE , Earth , 10 " 2 8918 WASHER , Clutch - Hardened Steel 1 EBOLT BOLT , Hex , 1 / 4 " - 28 x 5 / 8 " , Grade 5 , ( earth blade to auger ) 8919 GASKET 2 1 ENUT NUT , Nylock , 1 / 4 " - 28 , ( earth blade to auger ) 8920 CENTRIFUGAL CLUTCH ROTOR 1 GCA GAS CAP 1 8920A CENTRIFUGAL CLUTCH SPRING 2 GT49B GAS TANK 1 8920B CENTRIFUGAL CLUTCH SHOES 2 2 IB5816 BOLT , 5mm x 0.8 x 16mm , ( ice blade to auger ) 2 89210B HANDLEBAR - 2 Person , w / throttle mounting tab 1 IN58 NUT , 5mm x 0.8 Nylock , ( ice blade to auger ) 8922 BALL BEARING 1 3 PBP8A BLADE PROTECTOR , Ice , 8 " 8923 BALL BEARING 1 2 PBPIOA BLADE PROTECTOR , Ice , 10 " 8924 SNAP RING 2 3 QB6 BLADE , Ice , 6 " 2 8929 BOLT - SHCS , 1 / 4 " - 20 x 1 - 1 / 2 " 2 QB8 BLADE , Ice , 8 " 2 ( gear case bottom to gear case top ) QB10 BLADE , Ice , 10 " 8930 BOLT - Hex Hd , 1 / 4 " - 20 x 3 / 4 " , Grade 5 1 4 QT6N ICE AUGER , 6 " 1 ( handlebar plate to engine ) QT8N ICE AUGER , 8 " 1 8931 BOLT - SHCS , 1 / 4 " - 20 x 2 " 4 QTION ICE AUGER , 10 " TC300 GAS ENGINE 1 ( gear case to handlebar plate ) 2 8932 NUT - Hex , 1 / 4 " - 20 Keps WF516 WASHER - FLAT , 5 / 16 " , ( auger shock spring ) 8938 GEAR CASE , ( upper half ) Parts can be obtained from the store where your auger was purchased or O Ordering repair parts direct from the factory . To order from the factory , call or write to : 1360 1st Avenue ; RO . Box666 Cumberland , Wisconsin 54829 V ( 71A5 ) 8R22D - 24I1S5 AFMax ( , 715I ) N82C241 . 80 1 - 800 - 3456 - 007 www . ardisam . com Please include the following information with your order : 1 . Part numbers 2 . Part description 3 . Quantity 4 . Model number and serial number
Page: 6
y EARTHQUAKE MODEL 9200 AV520 GCA \ Part # Description GT3HP " \ H H 60G30 CLUTCH DRUM 60G38 SPRING PIN , 7 / 32 " x 1 - 1 / 8 _ ' 903E _ 60G56 NUT - Hex , 5 / 16 " - 18 , two way reversible locknut 407 BOLT - SHCS , 5 / 16 " - 18 x 518 " , ( handlebar plate _ o engine ) 719 LOCKWASHER - Spring , 3 / 8 " 903E DECAL , Earthquake 928A SHOULDER NUT , 5 / 16 " - 18 9205C 1423 BOLT - HHCS , 5 / 16 " - lg x 2 " , Grade 5 , ( auger shock spring ) \ 1433 BOLT - Hex Hd , 3 / 8 " - 16 x 1 - 1 / 2 " , ( auger to powerhead ) 9205D 1501 BOLT - Hex Hd , 5 / 16 " - 18 x 3 / 4 " , Grade 5 , Zinc 2104 NUT - Hex , 3 / 8 " - 16 , Locking 8913 SHAFT , Output , 7 / 8 " 8914 48T GEAR 8915 DOWEL PIN , 1 / 4 " x 1 / 2 " , Hardened Steel 9217 7T PINION GEAR 504 _ = 8919 GASKET 8922 BALL BEARING 9210C 8923 BALL BEARING 8924 SNAP RING ! _ 407 ( 4 places ) 8929 BOLT - SHCS , 1 / 4 " - 20 x 1 - 1 / 2 " ( gear case bottom to gear case top ) 9020 8931 BOLT - SHCS , 1 / 4 " - 20 x 2 " ( gear case to handlebar plate ) 8939 GEAR CASE , ( lower hall ) 895g POINT , Earth 8958HD POINT , Fishtail g9g0 EARTH AUGER SPRING , ( 6 " - 10 " only ) 9020 CENTRIFUGAL CLUTCH ROTOR 9020A CENTRIFUGAL CLUTCH SPRING 9020B CENTRIFUGAL CLUTCH SHOES 9038 GEAR CASE , ( upper half ) 9205C THROTTLE FINGER TIP CONTROL _ < _ 8922 9205D THROTTLE CONTROL ROD 9038 9210C HANDLEBAR - 2 Person , w / throttle mounting tab 9211 HANDLE GRIP , 7 / 8 " ID 9214A 10T PINION GEAR 9216 GEAR CLUSTER - 48T GEAR & 10T PINION ( includes 8924 , 8915 , 8914 , & 9214A } _ , _ 8924 = / 8919 AV520 GAS ENGINE EA2F EARTH AUGER , 2 " , w / fishtail poit _ t EA3F EARTH AUGER , 3 " , w / fishtail point _ = / 8923 EA4P EARTH AUGER , 4 " , w / fishtail point EA6P EARTH AUGER , 6 " , w / fishtail poir _ t _ f8924 / - I _ 8924 EA8F EARTH AUGER , 8 " , w / fishtail point EAIOF EARTH AUGER , 10 " , w / fishtail point EB4 BLADE , Emlh , 4 " _ 915 _ _ , / _ - 8915 ' EB6 BLADE , Emlh , 6 " 0 _ 8912 _ EB8 BLADE , Emlh , 8 " EBI0 BLADE , Earih , 10 " EBOLT BOLT , Hex , 1 / 4 " - 28 x 5 / 8 " , Grade 5 , Q _ . . , . s18914 ( earth blade to auger ) _ d _ I ENUT NUT , Nylock , 1 / 4 " - 28 , ( earth Nade to auger ) GCA GAS CAP GT3HP GAS TANK WF516 WASHER - FLAT , 5 / 16 " , ( wager shock sprh _ g ) [ < _ _ 8922 - - 8931 ( 4 places ) _ < _ 8913
Page: 7
ACCESSORIES We at Ardisam take pride in serving our customers with any additional needs you might have . We carry a full line of accessories for your ice / earth auger . All you have to do is call us anytime during business hours ( Central Time ) and we'll be happy to help provide you with the products you need . Our toll free number is 1 - 800 - 3456 - 007 . IMPORTANT : State Model Number of Unit When Ordering . If you have purchased this unit as an ice auger and you desire to Should you need additional depth extension for earth or ice : use it for post hole drilling , you may order an earth auger direct EXT6 . . . . . . . . . . . . . . . . . 6 " Extension from the factory if your dealer does not stock required parts : EXTI2 . . . . . . . . . . . . . 12 " Extension EXTI8 . . . . . . . . . . . . . 18 " Extension EAIOF . . . . . . . . . . . . . . 10 " Earth Auger EA8F . . . . . . . . . . . . . . . . . . 8 " Earth Auger EA6F . . . . . . . . . . . . . . . . . . 6 " Earth Auger EA4F . . . . . . . . . . . . . . . . . . 4 " Earth Auger EA3F . . . . . . . . . . . . . . . . . . 3 " Earth Auger Earth Replacement Blades ( includes nuts & bolts ) EA2F . . . . . . . . . . . . . . . . . . 2 " Earth Auger EB4 . . . . . . . . . . . . . . . . . . . . . 4 " Earth Replacement Blade EB6 . . . . . . . . . . . . . . . . . . . . . 6 " Earth Replacement Blade EB8 . . . . . . . . . . . . . . . . . . . . . 8 " Earth Replacement Blade EBI0 . . . . . . . . . . . . . . . . . 10 " Earth Replacement Blade EBOLT . . . . . . . . . . . . . . Bolt - Hex Hd , 1 / 4 - 28 x 5 / 8 " , Grade 5 If you have purchased this unit as an earth auger and you desire to ENUT . . . . . . . . . . . . . . . Nut - Nylock , 1 / 4 - 28 use it for ice fishing , you may order an ice auger direct from the factory if your dealer does not stock required parts : Ice Replacement Blades ( includes nuts & bolts ) QB6 . . . . . . . . . . . . . . . . . . . . 6 " Quantum Series ( Set of 2 ) QB8 . . . . . . . . . . . . . . . . . . . . 8 " Quantum Series ( Set of 2 ) QT6N . . . . . . . . . . . . . . . . . 6 " Ice Auger QB10 . . . . . . . . . . . . . . . . 10 " Quantum Series ( Set of 2 ) r QT8N . . . . . . . . . . . . . . . . . 8 " Ice Auger IB5816 . . . . . . . . . . . . . . Bolt , 5ram x 0.8 x 16ram [ , QTION . . . . . . . . . . . . . 10 " Ice Auger IN58 . . . . . . . . . . . . . . . . . . Nut - Nylock , 5rran x 0.8 Other Accessories ADAPT3 1 / 2 " Chuck Adapter , Does Not Include Adapter or Chuck DtSPW . . . . . . . . . . . . . . . Wall Hanger for Powerhead / Auger Storage NOTE : DO NOT USE AN EARTH AUGER IN ICE OR SHARPI . . . . . . . . . . . . . Dimnond Sharpener Hone - Fine AN ICE AUGER IN EARTH . SHARP2 . . . . . . . . . . . . . Diamond Sharpener Hone - Medium U . S . FUNDS ONLY
Page: 8
EARTHQUAKE TILLERS & WARRANTY Ardisam , Inc . manufactures a quality line of Gear Drive Rear Tine Rototillers . See literature attached herewith or contact the factory for a dealer in your area . Earthquake Model 5020 - 5HP or Earthquake Model 5020E - 5HP Electric Start One Year Limited Warranty The Ardisam , Inc . , Manufacturing Company warrants this Eskimo ® or Earthquake ® Auger to be free from defects in material or workmanship . Conditions of this warranty include : What is covered under warranty : Ardisam , Inc . will repair or replace any part defective in workmanship or material within one year after delivery of the auger to the original purchaser . What is not covered under warranty : This warranty applies only to products which have not been repaired or altered outside our factory . It covers only defects resulting from normal use , and does not cover defects arising from misuse , alteration , negligence , commercial use , or accident . This warranty applies only to the original purchaser , and is not transferrable . How to obtain service : Return the product to us at the address below with transportation charges prepaid . This warranty supersedes all other warranties either expressed or implied and all other obligations or liabilities on our part . Ardisam , Inc . , does not assume , and does not authorize any other person to assume for us , any liability in connection with the sale of our products . This guarantee is void unless warranty card is properly filled out and returned to Ardisam , Inc . , Cumberland Wisconsin , at time of purchase . ARDISAM , INC . 13601stAvenue ; RO . Box666 CumberlandW , isconsin54829 ( 715 ) 822 - 2415 Fax ( 715 ) 8224180 1 - 800 - 3456 - 007 www . ardlsam . oom Part # OM89A Rev . 2 - 010801