Register / log-in to add to your Hammerwall Collection.
Manual Location
The Search Results for the Search Section to the left will appear here.
Page: 1
USER’S MANUAL Part 2 2.4 GHz Expansion Handset 2300 Please also read Part 1 — Important Product Information © 2002 Advanced American Telephones . All rights reserved . AT & T and the Globe Design are trademarks of AT & T Corp . licensed to Advanced American Telephones .
Page: 2
Visit us at www.telephones.att.com © 2002 Advanced American Telephones . All rights reserved . AT & T and the Globe Design are trademarks of AT & T Corp . licensed to Advanced American Telephones . Printed in China . Issue 1AT & T 07 / 02
Page: 3
CONTENTS NTENTS BEFORE YOU BEGIN . . . . . . 1 Parts List . . . . . . . . . . . . . . . 1 Compatiblity . . . . . . . . . . . . . 2 About Handset Registration . . 2 INSTALLATION . . . . . . . . . . 3 O Charging Stand Installation . . . 3 C Belt Clip . . . . . . . . . . . . . . . . 5 Headset . . . . . . . . . . . . . . . . 5 FEATURE SETUP AND OPERATION . . . . . . . 6 DEFAULT SETTINGS . . . . . . . 7 TECHNICAL SPECIFICATIONS . . . . . . . 8
Page: 4
BEFORE YOU BEGIN Parts List Your box should include : EGIN This User’s Handset USER’S MANUAL Manual B Part 2 YOU 2.4 GHz Expansion Handset 2300 FORE Please also read Part 1 — Important Product Information © 2002 Advanced American Telephones . All rights reserved . E AT & T and the Globe Design are trademarks of AT & T Corp . licensed to Advanced American Telephones . B Charging Stand NiCd battery pack 1
Page: 5
Compatibility This AT & T 2300 expansion handset is compatible with the AT & T 2320 , BEGIN 2325 , 2355 and 2365 telephones . You may add up to three expansion handsets to your compatible telephone , for a total of four handsets . If you try to install a fifth handset , registration will be blocked . YOU About Handset Registration Each expansion handset must be individually registered with your AT & T 2320 , 2325 , 2355 or 2365 base . Registration happens BEFORE automatically when you place this handset fully charged into your current base . ( See INSTALLATION beginning on page 3 ) . The original handset that came with the base is automatically registered as Handset 1 . Additional handsets will be assigned Handset 2 , Handset 3 and Handset 4 . You can rename the handsets by following the directions under “ Handset Name � in the FEATURE SETUP section of your base telephone User’s Manual . 2
Page: 6
INSTALLATION Charging Stand Installation NOTE : Install the charging stand away from electronic � INSTALLATION equipment , such as personal computers , television sets or microwave ovens . Avoid excessive heat , cold , dust or moisture . 1 Connect the power cord to an electrical outlet not controlled by a wall switch . Standard electrical outlet 3
Page: 7
2 Install the handset battery . Use only AT & T Battery 3301 , SKU # 91076 . INSTALLATION a ) Remove battery b ) Plug the battery pack compartment cover by connector into handset . pressing on indentation Place the battery pack and and sliding downward . wires in the compartment . c ) Replace cover by sliding it on its track up over battery case until it snaps firmly into place . 3 Charge the handset battery . • Place the handset in the charging stand . • Charge the battery at least 12 hours . After the first charge , the battery will charge in eight hours . 4 Register your handset . After handset is fully charged place it in the base of your 2320 , 2325 , 2355 , or 2365 telephone , it will automatically be registered and you will hear a single beep . If you try to register a fifth handset , registration will be blocked . 5 Check for dial tone . Lift the handset and press P ; you should hear a dial tone . 4
Page: 8
Belt Clip You can remove a ) Pull clip b ) Press tabs the belt clip ATION away from on belt clip from the handset to into slots handset . remove . on back of handset to Headset reattach . LL You can use this telephone INSTA hands - free when you install any industry standard 2.5 mm headset ( purchased separately ) . For best results use an AT & T 2.5 mm headset . Plug the headset into the jack located on the right side of the handset ( under the small rubber flap ) . Do not force the connection , but make sure the plug fits securely . 5
Page: 9
FEATURE SETUP AND OPERATION FOR INSTRUCTIONS OPERATION TO SETUP AND OPERATE THIS EXPANSION HANDSET , REFER TO THE MANUAL AND THAT CAME WITH YOUR SETUP ORIGINAL BASE FEATURETELEPHONE . 6
Page: 10
DEFAULT SETTING DEFAULT SETTINGS FUNCTION : DEFAULT SETTING : Dial Method Tone SETTINGS Handset Volume 2 Ring Volume 6 External Ring Pattern 0 Internal Ring Pattern 1 DEFAULT Key Click ON 7
Page: 11
TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS Frequency Range 2400 MHz – 2483 MHz Channels 95 NS Channel Spacing 864 kHz Output Power 23 SPECIFICATIOdBm Sensitivity - 92 dBm Modulation GFSK Operating Temperature 0 ° C – 40 ° C Base Unit Voltage 96 – 144 Vrms ( AC Voltage , 60Hz ) Base Unit Voltage 9 Vdc TECHNICAL ( AC Adapter Output ) Handset Voltage 3.6 – 4.6 Vdc , 600mAh 8