Home | Register Login | Wanted Manuals | MarketPlace | Members Area | Manuals Manufacturer Directory | UPC Lookup | Information Pages | Policy


Back To Craftsman Table Saw       Model: 113.221770 or 113221770 Craftsman 10 Inch Bench Top Table Saw
Regular Text Search or Search by Model Number

Register / log-in to add to your Hammerwall Collection.
Manual Location


This is a partial text extraction from the pdf, to download the pdf, click the Manual tab. If you want to search this text, hold control and F, and type the word you are looking for.

Page: 1

F • Save This Manual For Future Reference SEARS owner's manual MODEL NO . 113,221770 I Serial Number may be found at the rear of the Model and serial numbers _ I _ _ RS AM / CRA base . iNCH BENCH TOP You should record both model 1 0 and serial number in a safe place for future use , TABLE SAW I • assembly YOUR • operating ° repair parts SAFETY READ ALL INSTRUCTIONS CAREFULLY Sears , Roebuck and Co . , Hoffman Estates , IL 60179 U , S . A . Printed in U . S . A , 6 / 97 Part No , SP6048
Page: 2

p * FULL ONE YEAR WARRANTY ON CRAFTSMAN TABLE SAW If within one year from the date of purchase , this Craftsman Table Saw fails due to a defect in mate - rial or workmanship , Sears will repair it , free of charge . WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SERVICE CENTER / DEPARTMENT THROUGHOUT THE UNITED STATES . This warranty applies only while this product is used in the United States . This warranty gives you specific legal rights , and you may also have other rights which vary from state to state . Sears , Roebuck and Co . , D / B17 WA Hoffman Estates , IL 60179 3afoty Instructions For Table Saw Safety Signal Words When installing Or Moving The Saw DANGER : means if the safety information is not followed Avoid dangerous environment . someone will be seriously injured or killed • Use the saw in a dry , indoor place protected from rain . WARNING : means if the safety information is not followed Keep work area well lighted . someone could be seriously injured or killed . To avoid injury from unexpected saw movement . CAUTION : means if the safety information is not followed • Bolt or clamp the saw to firm level surface where there someone may be injured . is plenty of morn to handle and properly support the workpiece ( See page 18 - 19 ) . Before Using The Saw • Support the saw so the table is level and the saw does WARNING : to avoid mistakes that could cause serf - I not rock . ous , permanent injury , donor plug the table saw in _ 1 • When using a table extension on any side of the saw , until the following steps have been satisfactorily I prop up the outer end of the extension from the floor or completed . I bench top to keep the saw from tipping . - Completely assemble and align saw ( See pages 8 - 18 ) • Put the saw where neither , operators nor bystanders • Learn the use and function of the ON - OFF switch ( See must stand in line with the sawblade . page 13 ) blade guard , spreader , anti - kickbackdevice , • To avoid injury from electrical shock , make sure your miter gauge , rip fence , table insert , blade elevation and fingers de not touch the plug's metal prongs when blade tilt contro is ( See page 21 ) . pluggingin or unplugging the saw . • Review and understand all safely instructions and • Never stand on tool . Serious injury could occur if the operating procedures inthis manual tool tips or you accidentally hit the cutting tool . Do not • Review the maintenance methods for this saw ( See store any items above or near the tool where anyone page 34 - 35 ) . might stand on the tool to reach them . • Find and read all the warning labels found on the saw ( shown below ) When servicing use only identical DOUBLE INSULATED replacement parts . u o _ mm u ) L ) _ ; ( 9 m _ t - - 0 ) u . m I • • • • li . . . . [ ' R _ ld m _ rluot before u _ ng _ sw . 6 . W _ n ripping , ule pullh _ ft = : kwhen fence h = eel 2 / ncbol or & Know bow t _ reduc : e _ e _ l _ k of k . Jckb _ k . 2 W , _ = _ • _ l _ zy goggl _ that me , el AN _ I Z87 . 1Stond _ rdt . mo _ ' e | tom blade . t 3 . Do rmt @ _ _ re _ hl = r _ d € u _ $ . 7 . Whin ripping , = Jim p _ llh block and _ xllll _ IMIoe whln Ilsnce tl _ . Keep Id _ a guard down lad In pile • _ = _ r through _ : uts . _ $ t _ | foefwee _ 1 / 21114 2 _ ncilel _ | rom bl _ , de . _ l 5 , Ke _ p hand _ _ t o _ pi | b zsfs _ w blade . DOno _ make rip _ uf $ rmrz _ wer thlm 1 / 2 WCI ' _ .
Page: 3

- To avoid bums or other fire damage , never use the Before Each Use saw near flammable licluids , vapors or gases . inspect your saw . - To avoid injury , don't do layout , assembly , or setup = To avoid injury from accidental starting , turn the switch work on the table while blade Is spinning . It could cut off unplug the saw . and remove the switch key before or throw anything hitting the blade . raising or removing the guard , changing the cutting Plan your work tool , changing the setup , or adjusting anything . o Plan ahead to protect your eyes , hands , face . ears . • Check for alignment of moving parts , binding of mov - Use The Right Tool . Don't force tool or attachment to ing parts , breakage of parts , saw stability , and any do a job it was not designed for . other conditions that may affect the way the saw works . Dress for safety ° Do not wear loose clothing , gloves neckties or jewelry • If any part is missing , bent or broken in any way , or any ( rings , wrist watches ) . They can get caught and draw electrical part does not work properly , turn the saw off you into moving parts . and unplug the saw . • Replace damaged or missing parts before using the • Wear nonslip footwear . saw again . • Tie back long hair . ° Use the sawblade guard , spreader and anti - kickback • Roll long sleeves above the elbow . pawls for any thru - sawing ( whenever the blade comes • Noise levels vary widely . To avoid possible hearing through the top of the workpiece ) . Make sure the anti - damage , wear ear plugs or muffs when using table kickback pawls work properly . Make sure the spreader saw for hours at a time is in line with sawblade ( See page 10 - 11 ) . ° Any power saw can throw foreign objects into the o Make sure all clamps and locks are tight and no parts eyes . This car result in permanent eye damage . Wear have any excessive play . safety goggles ( not glasses ) that comply with ANSI • Remove adjusting keys and wrenches . Form a habit of Z87 . 1 ( shown on package ) . Everyday eyeglasses have checking for and removing keys and adjusting only impact resistant lenses . They are not safety wrenches from table top before turning it on . glasses . Safety goggles are available at Sears retail stores . Glasses or goggles not in compliance with To Avoid injury From Jams , Slips Or Thrown ANSI Z87 . 1 could seriously hurt you when they break . Pieces ( Kickbacks Or Throwbacks ) WEAR YOUR Inspect your blade . • Choose the right blade or cutting accessory for the material and the type ot cutting you plan to do , • Never use grinding wheels , abrasive cutoff wheels . friction wheels ( metal cutting blades ) wire wheels or = For dusty operations , wear a dust mask along with buffing wheels . They can fly apart explosively . safety goggles . ° Choose and inspect your cuttingtool carefully : Inspect your workpiece . - To avoid cutting tool failure and thrown shrapnel • Make sure there are no nails or foreign objects in the ( broken pieces of blade ) , use only 10 inch or smaller part ol the workpiece to be cut . blades or other cutting tools marked for speeds of ° When cutting irregularly shaped workpleces , plan your 5000 rpm or higher . work so it will not slip and pinch the blade : - Always use unbroken , balanced blades designed to ° A piece of molding for example , must lie flat or be held fit this saw's 5 / 8 inch arbor . by a fixture or jig that wil ! not let it twist , rock or slip - When thru - sawing ( making cuts where the blade while being cut . Use jigs or fixtures where needed to comes through the workpiece top ) , always use a 10 prevent workpiece shifting . inch diameter blade . This keeps the spreader in ctos - • Use a different , better suited type of tool for work that est to the blade . can't be made stable . - Do not over tighten arbor nut . Use arbor wrenches to Plan your cut , " snug " it securely . • To avoid kickbacks and throwbacks - when a part or atl - Use only sharp blades with propedy set teeth . Con - of the workpiece binds on the blade and is thrown wo - sult a professional blade sharpener when in doubt . lently back toward the front of the saw : - Keep blades clean of gum and resin . - Never cut freehand . Always use either a rip fence . • Never use the saw without the proper blade insert . miter gauge or fixture to position and guide the work . Inspect your work area . so it won't twist or bind on the blade and kickback . • Keep work area clean . - Make sure there's no debris between the workpiece • Cluttered areas and benches invite accidents . Floor and its supports . must not be slippery from wax or sawdust .
Page: 4

Safety Instructions for Table Saw ( continued ) - Use extra caution with large , very small or awkward • Make sure the top of the arbor or cutting too ! turns toward the front of the saw . workpieces : • Use extra supports ( tables , saw horses , blocks , etc . ) Keep children away . for any workpieces large enough to tip when not held • Keep all visitors a safe distance from the table saw . down to the table top . Never use another person as a + Make sure bystanders are clear of the table saw and substitute for a table extension , or as additional sup - workplace . port for a workplace that is longer or wider than the Don't force tool . basic saw table , or to help feed , support or pull lhe * Letthe blade reach full speed before cutting . workplace . o It will do the job better and safer at its designed rate . • Never confine the piece being cut off . that is , the piece - Feed the workpiece intothe saw only fast enough to let not against the fence , miter gauge or fixture . Never the blade cut without bogging clown or binding . hold it , clamp it , touch it , or use length stops against it , It must be free to move . Jf confined , it could get Before freeing jammed material . wedged against the blade and cause a kickback or - Turn switch " OFF " . throwback . - Unplug the saw . • Never cut more than one workpiece at a time . - Wait for all mov = ngparts to stop . • Never turn your table saw " ON " before clearing every - o Check blade , spreader and fence for proper alignment thing except the workplace and related support before starting again . devices off the table . To avoid throwback of cut off pieces . Plan the way you will push the workpiece through . ° Use the guard assembly . • Never pull the workplace through . Start and finish To remove loose pieces beneath or trapped inside the cut from the front of the table saw . the guard , • Never put your fingers or hands in the path of the - Turn saw " OFF " sawblade or other cutting tool . - Remove switch key . • Never reach in back of the cutting tool with either = Wait for blade to stop before lifting the guard . hand to hold down , support the workpiece , remove Before leaving the saw . wood scraps , or for any other reason . ° Avoid hand positions where a sudden slip could cause • Turn the saw off . fingers or hand to move into a sawblada or other cut - o Wait for blade to stop spinning . ting tool . - Unplug the saw . • Oon't Overreach . Always keep good tooting and bal - o Make workshop chUd - proof . Lock the shop . Disconnect ance . master switches . Remove the yellow switch key , Store • Push the workplace against the rotation of the blade . it away from children and others not qualified to use the tool Never feed material into the cutting tool from the rear ot the saw . Additional Safety Instructions for • Always push the workplace all the way past the saw - Rip Type Cuts blade . Before starting . • As much as possible , keep your face and body to one o Never use the miter gauge when ripping . side of the sawblade , out of line with a possible kick - back or throwback . - Use a push stick whenever the fence is 2 or more • Set the cutting tool as low as possible for the cut you're inches from the blade , planning . * When thru - sawing , use an auxiliary fence and push Avoid accidental starting , block whenever the fence must be between 1 / 2 and 2 - Make sure switch is " OFF " before plugging saw into a inches of the blade . power outlet . • Never thru - saw rip cuts narrower than 1 / 2 inch . ( See Whenever Sawblade Is Spinning " Basic Saw Operations - Ripping and Bevel Ripping " section . ) WARNING : Don't allow familiarity ( gained from fre - • Never rip anything shorter than 10 " long . quent use of your table saw ) cause a careless mis - • When using a push stick or push block , the trailing end take . Always remember that a careless fraction of a ! ot the board must be square . A push stick or block second is enough to cause a severe injury . against an uneven end could slip off or push the work • Before actually cutting with the saw , watch it while it away from the fence . runs for a short while . If it makes an unfamiliar noise or • A Featherboard can help guide the workpiece . ( See vibrates a lot , stop immediately . Turn the saw off . " Basic Saw Operation - Using Featherboards for Thru - Unplug the saw . Do not restart until finding and cor - Sawing " section . ) recting the problem .
Page: 5

When thru - sawing . • Alwaysusefeatherboardfsor anynonthrurip type cuts . o To avoid kickbacks and slips into the blade , always Make From 3 / 4 " Thick Solid Wood push forward on the section of the workpiece between the sawbtade and the rip fence , Never push forward on E _ 24 " the piece being cut off . Additional Safety Instructions For Crosscut Type Cuts Ko . A . . bou , ! l Before starting . • Never use the rip fence when crosscutting . 4 - 1 / 2 _ 5 - " - I Featherboard oAn auxilia _ , wood facing attached to the miter gauge can help prevent workpiece twisting and throwbacks . Attach it • To avoid kickbacks and slips into the blade make sure to the holes provided . Make the facing long enough and the rip fence is parallel to the sawblade . big enough to support your work . Make sure . however , it o Before fhru - sawing , check the anti - kickback pawls . will not interferewith the sawblade guard _ ( See " Basic Saw Operation - Using The Rip Fence . " - Use jigs or fixtures to hetp hold any piece too small to The pawls must stop a kickback once it has started . extend across the full length of the miter gauge face Replace or sharpen anti - kickback pawls when points during the cut . This lets you properly hold the miter become dul ! , gauge and workpiece and helps keep your hands • Plastic and composition ( like hardboard ) materials may away from the blade , be cut on your saw . However . since these are usually When cutting . quite hard and slippery , the anti - kickback pawls may - To avoid blade contact , always hold the miler gauge as not stop a kickback . Therefore , be especially careful in shown in " Basic Saw Operations - Using The Miler Gauge your setup and cutting procedures . Glossary of Terms for Woodworking Kerr Anti - Kickback Pawls ( AKP ) The amount of material removed by the blade in a Device which , when properly maintained , is designed to through cut . Also the slot produced by the blade in a non - stop the workpiece from being kicked back at the opera - through or padial cut tor during ripping operation . Kickback Arbor An uncontrolled grabbing and throwing of the workp _ ece The shaft on which a cutting tool is mounted . back toward the front of the saw , Bevel Cut Leading End An angle cutting operation made through the face of the The end of the workpiece which , during a rip type opera - workpiece . tion . is pushed into the cutting tool first . Compound Cut Miter Cut A simultaneous bevel and miter crosscutting operation . An angle cutting operation made across the width of the Crosscut workpiece . A cutting operation made across the width of the work - Molding piece . A non through cut which produces a special shape in the Dado workpiece used for joining or decoration . A non thru cut which produces a square sided notch or Push Stick trough in the workpiece . A device used to feed the workpiece through the saw Featherboard during narrow ripping type operations . The push stick A device which can help guide workpieces during rip type helps keep the operator's hands well away from the operation . blade . Freehand Push Block Performing a cut without the use of fence ( guide ) , miter A device used for npping type operations too narrow to gauge , fixture , hold down or other proper device to pre - a ! low use of a push stick vent the workpiece from twistingduring the cutting opera - Rabbet tion . Twisting of the workpiece can cause it to be thrown . A notch in the edge of a workpiece . Gum Resin A sticky , sap based residue from wood products . A sticky , sap based substance that has hardened . Heel Revolutions Per Minute ( RPM ) Misalignment of the sawblade such that the blade is not The number of turns completed by a spinning object in parallel to the miter gauge groove . one minute .
Page: 6

Glossary of Terms for Woodworking ( continued ) Thru - Sawing Rip Cut Any cutting operation where the blade extends com - A cutting operation along the lenglh of the workpiece . pletely through lhe thickness of the workpiece . Sawblade Path Trailing End The area oi the workpiece or table top directly in line with either the tmvetof the blade or the part of the workpiece The workpiece end last cut by the blade in a rippingoper - ation . which will be , or has been cut by the blade . Set Workpiece The distance that the tip of the sawblade tooth is bent ( or The item on which the cutting operation is being per - set ) outward from the face of the blade . lormed . The surfaces of a workpiece are commonly Throw - Back referred to as faces , ends , and edges . Throwing of pieces in a manner similar to a kickback . Motor Specifications and Electrical Requirements Power Supply and Motor Specifications Polarized Plug The AC motor used in this saw is a universal , nonrevers - Your unit has a plug that looks like the one shown below . ible type having the following specifications : Maximum Developed HP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1 / 2 Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Amperes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Hedz ( Cycles ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Single RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4700 Rotation of Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Counterclockwise To reduce the risk of electrical shock , this appliance has a polarized plug ( one blade is wider than the other ) . This WARNING : To avoid electrical hazards , fire haz - plug will fit in a polarized outlet only one way . If the plug ards , or damage to the tool , use proper circuit pro - does not fit fully in the outlet , reverse plug . If it still does tection . Yoursaw is wired at the factory for 120v not fit , contact a qualified electrician to install the proper operation . Connect to a 120v , 15 - amp branch cir - outlet . Do not change the plug in any way . WARNING : Damaged power cords can cause worn or cut , or damaged in any way , have it shock or fires . If the power cord is worn , cut , or damaged in any way , have it replaced immediately . • replaced immediately . tion . ' e IMPORTANT . To avoid motor damag , this motor should WARNING : Double insulation does not take the l be blown out or vacuumed frequently to keep sawdust place of normal safety precautions when operating from interfering with normal motor ventilation , this tool . ' 1 , Connect this tool to a 120v , 15 - amp branch circuitWith a 15 - amp time delay fuse or circuit breaker . Using the DANGER : To avoid electrocution : 1 . Use only identical replacement parts when ser - ' a es " c " " " " 2.1f the motor won t st rt , _ tumth wit h OFF immedi - vicing a tool with double insulation . Servicing ately . Unplug The Tool . Check the sawblade to make should be performed by a qualified service tech - sure it turns freely . If the blade is free . try to start the nician . motor again . If the motor still does not starl , refer to the 2 . Do not expose to rain , use in damp location or " Troubleshooting Chart " on page 35 . where floor is wet . 3 . If the motor suddenly stalls while cutting wood , turn the This tool is intended for indoor residential use switch " OFF " , unplug the tool , and tree the blade from only . the wood . The motor may now be restarted and the cut finished . 4 . Fuses may " blow " or circuit breakers may trip fre - quently if :
Page: 7

a . MotorIs OverloadedO . verloadincganoccurif you 5 . Most motor troubles may be traced to Boose or # _ c : or - feedtoo rapidlyor maketoomanystart ! stopsin a rect connections , overload , low voltage ( such as sm _ ll shorttime . size wire in the supply circuit ) or h _ overly tong s , JpP { Y b . Voltagesnot morethan10 % aboveor belowtheori - circuit wire . Always check the connections , the load nameplatevoltagecan handlenormalloads . eFrmplate . and the supply circuit whenever motor doesn't work heavyloads , howevert , hevoltageat motort well . Check wire sizes and length with the Wire S _ ze Chart . nalsmustequalthevoltagespecifiedonname Wire Size Overload Protection Your saw features a reset overload relay button . If the NOTE : Make sure the proper extension cord is used _ d is in good condition . motor stops running or fails to start ( due to feed pres - sure too fast , dull blade or low voltage ) , turn switch The use of any extension cord wi ! l cause some toss of " OFF " , let the motor cool three to five minutes and power , To keep this to a rninimum and to prevent over push the reset button , which resets the overload heating and motor burnout , use the table to determine device and allows you to turn the saw back on . the minimum wire size ( A . W , G . ) extension cord . WARNING : The ON / OFF switch should be in the off Wire Sizes Required Extension Cord position , and the plug removed from the power ( A . W . G , ) Length source while the cool down takes place to prevent t10 - 120V accidental starting when the reset button is 0 - 25 pushed , Overheating may be caused by misaligned 14 parts or dull blade , Inspect your saw for proper 26 - 50 12 setup before using it again , Table of Contents Checking Blade Parallel to the Miter Gauge Groove . . 15 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Adjusting Blade Parallel to Miter Gauge Groove . . . . . . . . . 16 Safety Instructions For Table Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Removing Sawblade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Safety Signal Words : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installing Sawblade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . t 7 Before Using The Saw : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Mounting Table Saw to Workbench , Cabinet or Legsei 18 When Installing Or Moving The Saw : . . . . . . . . . . . . . . . . . . . . . . . . . 2 Before Each Use : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Workbench Mounting Using Hardware . . . . . . . . . . . . . . . . . . . . . 18 Whenever Sawblade Is Spinning : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Workbench Mounting Using " C " Clamps . . . . . . . . . . . . . . . . . . . 18 Cabinet or Legset Mounting Using Hardware . . . . . . . . . . . 18 Additional Safety Instructions for : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Rip Type Cuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Getting to Know Your Table Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Before starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Work Feed Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Additional Safety Instructions For : . . . . . . . . . . . . . . . . . . . . . . . . . . . _ . . 5 Push Stick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Crosscut Type Cuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Push Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Glossary of Terms for Woodworking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Auxiliary Fence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Motor Specifications and Elec { rical Requirements . . . . . . . . 6 Safety Instructions for Basic Saw Operations . . . . . . . . . . . . . . 24 Power Supply and Motor Specifications . . . . . . . . . . . . . . . . . . . . . . 6 Before Each Use : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Double Insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Whenever Sawblade Is Spinning : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 ; Polarized Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Basic Saw Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Motor Safety Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Additional Safety Instructions for Crosscutting . . . . . . . . . . 26 Overload Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Crosscutting . . . . . . . . . . . . . . 26 Wire Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Repetitive Crosscutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 . . . . . . . . . . . . . . 2 Miter Crosscutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unpacking and Checking Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Bevel Crosscutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Tools Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Compound Miter Crosscutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Table of Loose Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Additional Safety Instructions for Rip Cuts . . . . . . . . . . . . . . . 28 List of Loose Parts in the Box and Bags . . . . . . . . . . . . . . . . . . . . . 9 Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Assembling Handle to Handwheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Bevel Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Blade Guard Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Blade Guard Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Resawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Checking Anti - kickback Pawls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Dadoing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rabbeting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Rip Fence Assembly and Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Ploughing or Molding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3334 Rip Fence Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Installation and Operation of Molding Head . . . . . . . . . . . . . . . . . Rip Fence Indicator Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Maintaining Your Table Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Miter Gauge and indicator Adjustment . . . . . . . . . . . . . . . . . . . . . . . . 13 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 On - Off Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Blade Tilting Control and Lock Lever Adjustment . . . . . . . . 14 Sears Recommends the Fol ow ng Accessor es . . . . . . . . . 35 Adjusting 90 and 45 Degree Positive Stops . . . . . . . . . . . . . . . . . 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 _ Adjusting Positive Stop at 90 Degrees . . . . . . . . . . . . . . . . . . . . . . 14 Troubleshooting . . - . . . . . . . . 3.7 . . . . Adjusting Positive Stop at 45 Degrees . . . . . . . . . . . . . . . . . . . . . . 14 Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3 . . . . . . . . . . . . . . . . . Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Blade Tilt Indicator Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Page: 8

Unpacking and Checking Contents Tools Needed Combination Square must be true . Check its accuracy as shown below . # 2 Phillips Screwdriver Select the straight edge of 3 / 4 " thick board . This edge Draw light line on board alon edge must be perfectly straight , Combination Square / Medium Screwdriver NOTE : The square and straight edge are used to align the saw . They must be accurate if the saw is to be Adjustable Wrench aligned properly , Should be gap or overlap here when square is flipped over in dotted position Apply a coal of automobile wax to the table . Wipe al Separate all parts lrom packing material and check each one with the illustration and the list of Loose Parts to parts thoroughly with a clean , dry cloth . This will reduce friction when pushing workpiece . make certain all items are accounted for , before discard - ing any packing material . WARNING : For your own safety , never connect plug to power source outlet until all assembly wARNING : If any parts are missing , do not attempt I steps are complete , and you have read and under - to assemble the table saw , plug in the power cord stand the safety and operating instructions . or turn the switch on until the missing parts are ! obtained and are installed correctly . Table of Loose Parts Item Description Qty A Table Saw Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 B B Miter Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 C Blade Guard and Spreader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 D Rip Fence ( Without Handle ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 E Owner's Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 F Bag ol Loose Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . * bag together and separate from contents of other bags .
Page: 9

List of Loose Parts in the Box and Bags Hex Screw - 1 / 4 - 20 x 1 / 2 " ( 2 ) Arbor Wrench ( 1 ) Shaft Wrench ( 1 ) Carriage Bolt - 1 / 4 - 20 x 718 " ( 1 ) Handle ( Rip Fence ) ( 1 ) Knob ( Handwheel ) ( 1 ) Hex Screw - 1 / 4 - 20 x 2 - 1 / 8 " ( 1 ) Flat Washer ( 1 ) © Spreader Support ( 1 ) Spreader Bracket ( 1 ) 1 / 4 " External Lockwasher 14 ) Q Nut Hex 5116 - 18 ( 1 ) Wing Nut 114 - 20 ( 1 ) Switch Key ( 1 ) Assembling Handle to Handwheel 1 . Thread screw into tapped hole in handwheel , as Handwheel shown . 2 . When properly assembled , the knob will rotate freely with only a small amount of play . 3 . Lock nut against handwheel . 1 / 3 _ Screw \ \ Nut Knob
Page: 10

Blade Guard Assembly 1 . From among the loose parts , locate the following hardware : 0 Hex Screw - Hex Screw - 114 - 20 x 2 - 1 / 8 " ( 1 ) Carriage Bolt - 1 / 4 - 20 x 7 / 8 " ( 1 ) 1 / 4 - 20 x 1t2 " ( 2 ) 0 114 " External Flat Washer ( 1 ) Wing Nut 1 / 4 - 20 ( 1 ) Spreader Support I1 ) Spreader Bracket ( 1 ) Lockwas her ( 4 ) 2 . Position large recessed shoulder end of the spreader support against end of pivot rod and fasten to table using the 1 / 4 - 20x2 - 1 / 8 " long hex screw and 1 / 4 " external tooth Iockwasher . / _ _ asher 1 / 4 " _ X Screw , , 1 / 4 - 20 x 2 - 1 / 8 . . Spreader Support 3 . Position the spreader bracket to the spreader sup - port as shown . The 1 / 4 - 20xl / 2 " screws and lock - washers are to be assembled finger tight only at this Blade Guard time . Bracket and Spreader 4 . Insert the 1 / 4 - 20 x 7 / 8 " carriage bolt in the square feature o1the spreader bracket as shown . Assemble the flat washer first , then the 1 / 4 external Iockwasher and the 1 / 4 - 20 wing nut on the carriage holt leaving Spreader the wing nut loose at this time . 5 . Assemble blade guard and spreader by positioning the open slot in the spreader directly above the Shouldered shouldered part of the rivet attached to the spreader bracket . Slide the spreader down between the spreader bracket and the head of the rivet until either the open slot sets on the rivet or the spreader sets Win on the table top surface . Tighten wing nut . NOTE : Both washers must be positioned between the Lockwasher 114 Carriage Bolt spreader and the wing nut . 1 / 2 - 20x7 / 8 10
Page: 11

Blade Guard Alignment IMPORTANT : To work properly , the spreader must always be adjusted so the cut workpiece will pass on Blade Guard either side of the spreader without binding or skewing to t / Arm the side . NOTE : The spreader is thinner than the width of the BladE NewspaperL _ _ Spreader KERF by approximately six thicknesses of newspaper . To check if alignment is proper , slide 3 thicknesses of newspaper between straight edge and spreader . Readjust if necessary . 1 . Make two folds in a small piece ( 6 " x 6 " ) of ordinary newspaper making three thicknesses . The folded paper will be used as a " spacing gauge " . Straigh _ - - - ' c _ - _ - . - _ J ' _ - _ ! ' J " _ . . _ Snreader 2 . Raise blade to maximum height and make sure blade is in vertical position ( straight up and down ) or at " 0 _ " blade angle . 3 . Lay a piece of straight flat wood or straight edge against the sawblade . Insert folded paper between spreader and wood strip . Position flatwasher & ! ockwasher 4 . Make sure the three hex screws are loose enough to on this side of spreader slide spreader bracket and to rotate spreader support . Space equals 3 5 . Lift the anti - kickback pawl to clear the wood or straight thicknesses of edge and hold the spreader tightly against the paper and wood . Make sure the wood is against the saw - paper _ Wood blade . Tighten the three hex screws . \ J This will align the spreader in the middle of the cut Blade ( KERF ) made by sawblade . / NOTE : To remove the guard for non - through cuts , loosen the wing nut and slide the guard upward off the soreader bracket . Do not disturb the setting of the spreader sup - port bracket . / / Looking Down on Saw When replacing the guard , slide the spreader down onto / the spreader support bracket with the washers directly / Space equals 3f under the wing nut . Make sure the wing nut is tightened thicknesses o securely . This lets you remove and replace the guard paper without disturbing the spreader alignment . Checking Anti - kickback Pawls 1 . Raise blade guard up to upright position . 2 . Rotate both pawls up toward rear el spreader . Let pawls go to make sure they return freely by spring force to their normal position . Anti - Kickback / 3 . Slide a sample workpiece under a pawl and pull it toward the front of the saw . Repeat for both pawls . 4 . The anti - kickback pawl should prevent the workpiece from moving toward the front of the saw . , laise 5 . See page 33 for instructions on how to sharpen the Pawls teeth of the anti - kickback pawls . t ° ' i 11
Page: 12

Rip Fence Assembly and Adjustment WARNING : To prevent personal injury , always dis - I connect plug from power source when making L adjustments . Q t _ Thread 5 / 16 - 18 nut all the way onto the fence locking handle . 2 . Thread rip fence locking handle into cam until tight . Nut Hex 5 / 16 - 18 ( 1 ) Handle ( Rip Fence ) ( 1 ) Lock the nut against cam with wrench . 3 . Place the rip fence on the table and lower the rip fence locking handle until the rip fence is secure to front rail . 4 . Check to see if rear clamp on the dp fence is loose , If not , turn the rip fence adjustment screw counterclock - wise until the rear clamp on the rip fen ce is loose with the fence assembly locked to the front rail . 5 . With fence assembly locked to front rail , turn the rip fence adjustment screw clockwise until rear clamp is snug . 6 _ Raise the rip fence locking handle . 7 . Turn the rip fence adjustment screw clockwise an addi - tional 1 / 2 turn . Rear Clamp 8 . Check the rip fence by applying moderate side pres - O sure to the rear of the fence assembly . If the rip fence deflects easily raise the rip fence locking handle and turn the rip fence adjustment screw clockwise another 1 / 4 turn . 9 . Check rip fence again by applying moderate side pres - sure to the rear of the fence assembly . If necessary repeat step 8 until rip fence is secure . NOTE : Overtightening the rip fence adjustment screw may cause the rip fence to be loose on the front table rail . Rip Fence Alignment ' WARNING : To prevent personal injury , always dis - connect plug from power source when making Rip Fence adjustments . Miter Gauge Adjusting Screws the blade to minimize the danger of kickback . For . . . . convenience , the rip fence will be aligned parallel to the miter gauge slot . The sawblade will be set or I CAUTION : The rip fence must be aligned parallel to adjusted parallel to the slot later . 1 . Place the ri _ cent to the miter gauge groove . 2 . Lower the rip fence locking handle to secure the rip fence . 3 . Check to see that the edge of the ri _ with the miter gauge groove If the rip fence is not parallel : oRaise the rip fence locking handle . ° Loosen the two hex head screws located on top of the rip fence . • Align the rip fence parallel to the miter gauge groove , = Lower the rip fence locking handle . - Tighten the two hex head screws previously loos - ened . 12
Page: 13

• Raise the rip fence rocking handle , move and return NOTE : To always obtain the best alignment of the rip the rip fence adjacent to the miter gauge groove , fence , develop the habit ol holding the front casting on lower the rip fence locking handle , the lence back against the table top while tightening the • Repeat and recheck steps 8 and 9 in the " Rip Fence fence lock handle . Tighten the rip | ence tock handle Assembly and Adjustment " section , securely to prevent rip fence movement while sawing . • The rip fence should now be parallel to the miter gauge groove , It not . repeat steps and recheck . Rip Fence Indicator Adjustment . . . . . . . . With the rip fence locked to the table measure the dis - tance from the side of the rip fence to the nearest side of the blade . The indicator should point to the same marking Scai _ _ _ _ 1 _ on the scale . If it does not , loosen the screw holding the indicator , move the indicator to the correct marking on the scale and tighten the screw . HINT : The rip fence indicator will need to be readjusted whenever a thicker or thinner blade is installed . When making critical cuts , make a trial cut on scrap wood rather Screw / than relying on the rip scales . Adjustment Miter Gauge and Indicator freely 1 . Check to make sure the miter gauge will slide through both entire table grooves before using it , 2 . To adjust the miter gauge , loosen lock knob and set the miter gauge body so the scale is at the 90 ' mark , then tighten lock knob , 3 . Make a cut on a piece of scrap wood . Check it with a square to see if the piece ol wood was cut at 90 ° . If the piece was not cut 90 ° . adjust the miter gauge body , tighten lock knob and make additional cuts until you are ceratin you have made a 90 ° cut . 4 . Loosen the miter scale adjustment screw set the indi - cator point on the 90 ° mark on the scale and tighten screw , On - Off Switch WARNING : For your own safety , lower blade or other cutting tool below table surface . ( If blade is the blade guard is correctly installed and uoperatingre I CAUTION : Before turning switch " ON " , make s I I tilted , return it to vertical , 90 ° position ) . Always properly . lock the switch " OFF " . When saw is not in use , The On - Off switch has a locking feature . This feature is remove key and keep it in a safe place . Also , in the intended to prevent unauthorized and possible hazard - event of a power failure ( all of your lights go out ) ous use by children and others . turn switch off and lock it by removing the key . 1 _ insert key into switch . This will prevent the saw from starting up again 2 . To turn saw " ON " , stand to either side of the blade . when the power comes back on . never in line with it : insert finger under switch lever and pull end of lever out . - After turning switch " ON " . always allow the blade to come up to full speed before cutting . - Do not cycle the motor switch on and off rapidly as this may cause the sawblade to loosen . In the event this should ever occur , allow the sawblade to come Switch Key to a complete stop , unplug saw and retighten the arbor nut normally , not excessively . - Never leave the saw while the power is " ON " . 3 . To turn saw " OFF " , push lever in . Never leave the saw until the cutting tool has come to a complete stop . 4 . To lock switch in " OFF " position , hold switch in with one hand and remove key with the other hand . 13
Page: 14

Blade Tilting Control and Lock Lever Adjustment 1 . Loosen blade tilting lock lever and slide the elevation EJevation Handwheel handwheel until blade is at desired angle and tighten blade tilt lock lever . 2 . If blade lock lever interferes with some object before blade tilting control mechanism is held tight or rigid , pull lock lever out and rotate lock Fever counterclock - wise to another position . Tighten lock lever . Recheck for proper adjustment of blade tilt lock lever , 3 . I1 lock lever won1 loosen enough so blade can be tilted , pull lock lever out and rotate lever clockwise to Blade Tilt Lock Lever another position . Tighten blade lock lever , Adjusting 90 and 45 Degree Positive Stops Your saw is equipped with positive stops for last and accurate positioning ol the sawblade at 90 and 45 degrees to the table . Always measure blade position from the left side of the blade . Blade insert may not be flush with table top . prevent personal injury , ahvays dis - I connect plug power Blade insert I WARNING : To from source _ vhen making I adjustments . ! Adjusting Positive Stop at 90 Degrees 1 . Unplug the saw . 2 . Turn elevation wheel clockwise and raise blade to maximum height , 3 . Loosen the blade tilt lock lever and push the elevation wheel to the left as far as possible and tighten the blade tilt lock lever 4 . Place a combination square on the table with one end of square against the blade as shown and checkto see if the blade is 90 ° to the table . 5 . If the blade is not 90 ° to the table , loosen the blade tilt lock lever , loosen 90 ° adjustment screw ( A ) a few turns and push the elevation wheel until the blade is 90 ° to \ the table \ 6 . Tighten blade tilt lock lever and tighten 90 ° adjustment ° " t 90 Adiustmen Screw ( A ) screw until it stops . 45 ° Adjustment Screw ( B ) / Adjusting Positive Stop at 45 Degrees 1 . Loosen the blade tilt lock lever and push elevation / wheel to the right as far as possible and tighten the / blade tilt lock lever . 2 . Place a combination square on the table with one end ol the square against the table as shown , and check to see if the blade is 45 ° to the table , 3 . It the blade is not 45 ° to the table loosen the blade tilt lock lever , loosen 45 ° adjustment screw ( B ) a few turns and push the elevation wheel until the blade is 45 ° to the table . 4 . Tighten blade tilt lock lever and tighten 45 ° adjustment screw until it stops , 14
Page: 15

Blade Tilt Indicator Adjustment 1 . With 90 ° positive stop set and blade tilt control pushed Indicator Pointer against this stop , loosen indicator screw , adjust indica - tor pointer to " 0 " degrees and retighten indicator screw . NOTE : When making critical cuts . make a trial cut on scrap wood rather than relying on the tilt scale or stops . Indicator Screw Checking Blade Parallel to the Miter Gauge Groove WARNING : To avoid injury from accidental start , make sure switch is " OFF " and plug is not con - nected to power source outlet . The blade was adjusted parallel to the miter gauge groove at the factory , in order to insure accurate cuts and help prevent kickback , this adjustment should be rechecked , If adjustment is necessary follow the steps below . WARNING : If the sawblade is NOT parallel with the miter gauge groove , it is said to have " HEEL " . This condition can cause the workpiece to bind or move away from the rip fence at the end of a rip cut , pos - sibly causing a kickback . 1 , Unplug saw . / / 2 . Turn elevation whee , and raise blade as high as it will Mark " X " on tooth go . 3 . Lift blade guard if already installed , to its highest posi - tion . 4 . Select a tooth on the front of sawblade that is set to the right when viewing blade from the front of the saw . and mark this tooth with a pencil 5 . Place the base of a combination square against the left edge of the right miter gauge groove , and extend the sliding rule ol square so it just touches the marked tooth . 6 . Rotate blade and check the same marked blade tooth at the rear of the saw table . 7 . If the front and back measurements are not identicaL , the mechanism must be adjusted to make the blade PARALLEL to miter gauge groove , 15
Page: 16

Adjusting Blade Parallel to Miter Gauge Groove - - WARNING : To avoid injury from accidental start , make sure switch is " OFF " and plug is not con - Alignment Screws nected to power source outlet . Secondaryent ( A ) ALignm I CAUTION : Fold a piece of cardboard over the blade Screws I to protect your hand NOTE : Always review the section " Checking Blade Par - allel to the Miter Gauge Groove " before proceeding with this section . 1 . Should your saw require adjustment the alignment screws must be loosened It you are unable to loosen the alignment screws from the top using a # 2 Phillips screwdriver proceed as follows : 2 . Unplug the saw . 3 . Remove the table insert . 4 . Remove the blade . 5 . Turn saw upside down . 6 . Locate the 4 nuts attached to the alignment screws ( A ) . Loosen these nuts 1 / 2 turn . 7 . Turn saw right side up and install blade 8 . Loosen 1 / 2 turn the four alignment screws ( A ) in the top of table next to the sawblade . This will allow the mechanism below the table to be shifted sideways . Cardboard 9 . Fold a piece of cardboard over the blade to protect your hands . 10 . Grasp the blade and the spreader support mecha - nism and move it to either the right or left a small amount as needed to make the square Iouch the same amount front and rear . Tighten one screw . 11 . Check with square to determine if marked tooth touches square by the same amount at front and rear . If it does , alternately tighten the other three screws slowty . If it does not , loosen screws and move blade the required amount . NOTE : If adjustment cannot be achieved by loosening the four alignmen ! screws ( A ) , loosen the two second - ary alignment screws ( B ) only if it is absolutely neces - sary to make this adjustment . 12 . Recheck blade clearance to table and table insert to make sure blade does not hit at both 90 and 45 degree blade tilt . 13 . If you cannot complete the alignment using alignment screws ( A ) , then proceed to secondary alignment screws ( B ) , if you cannot loosen secondary alignment screws ( B ) , remove blade and turn saw upside down , Locate the 2 nuts that are attached to the secondary alignment screws IB ) and loosen nuts 1 / 2 turn . 14 . Turn saw upright , reinstall blade and repeat steps 1 thru 5 . 15 . Once saw blade has been aligned , the screws need only to be tightened from the top side 16 . Reinstall the table insert and blade guard . Continue the assembly procedure as outlined in your owners manual . 16
Page: 17

Removing Sawblade Loosen WARNING : To avoid injury from accidental start , make sure switch is " OFF " and plug is not con - Open End Arbor " _ " _ - " _ ' _ Closed End nected to power source outlet . Shaft Wrench _ ) j Arbor Nut 1 . Unplug the saw . - - \ _ - _ f / " . . . Wrench 2 . Remove blade guard and retain hardware , 3 . Remove the phillips head screws from the blade insert . 4 . Lift the blade insert noting that the formed edge is toward the blade . Set insert aside . 5 . Turn elevation handwheel clockwise to raise sawblade as high as it will go . Stop or = Table f ' ° _ " d _ i / / - ' Arbor Nut 6 . Insert open end arbor shaft wrench over flal portions ol motor spacer and closed end arbor nut wrench over J arbor nut . Position wrenches as shown holding your hands well above blade . 7 . Hold arbor wrench against table and loosen arbor nut with arbor nut wrench by pulling it forward to you . 8 . Slide sawblade off motor shaft . Installing Sawblade 1 . Unplug the saw . Closed End 2 . Install sawblade onto shaft with the top blade teeth ; k _ Arbor Nut pointing toward front of saw . 3 _ Install blade collar with hollow surface toward blade . 4 . Install arbor nut . ench 5 . To tighten arbor nut , hold arbor wrench against rear of L Blade table , push arbor nut wrench towards rear of table , NOTE : Arbor nut should just be snug . Do not overtighten . _ ' - Insert _ r / / ! Arbor Nut 6 . Install blade insert in the table recess with its formed Tighten edge toward the blade . 7 . Insert screws through front and rear holes and tighten . IMPORTANT : Do not attempt to run saw without blade collar properly installed . Collar WARNING : To avoid injury from a thrown work - piece , blade parts , or blade contact , never operate saw without the proper insert in place . Use the sawblade insert when sawing . Use the dado / mold - ing head insert when using a dado or molding Top Teeth Pointing " _ . _ ' _ ' _ - - _ " _ head . See page 34 for Sears recommended acces - to Front of Saw sories . 8 . Re - install blade guard and tighten wingnut . Formed Edge \ \ 17
Page: 18

Mounting Table Saw to Workbench , Cabinet or Legset - - WARNING : To avoid injury from accidental start , make sure switch is " OFF " and plug is not con - - - - Workbench Surface . . . . . . . . . . . . . . . . m . . . . . . i nected to power source outlet . I WARNING : To avoid injury from kickback or saw movement the saw must be properly secured to a ; o - - - T sturdy workbench , cabinet or legset . Casters if provided onthe cabinet or legset must be locked during saw operation . If there is any tendency for I I 3 / 8 " Dia ! ' 9 / 1 _ " the saw to move or rock during operation , this 5 _ must be corrected immediately . = , ' Opening if Vacuum If table saw is to be used in a permanent location , is not used should be fastened securely to a firm supporting surface such as a workbench , cabinet or tegset using the four ! _ 0 _ mounting ' holes . I - _ - - 16 _ 9116 " - - - - - - - - _ 1 Workbench Mounting Using Hardware When mounting table saw to a workbench and using a ( Front of Table Saw ) vacuum hookup , holes should be drilled through the sup - Diagram of Workbench Mounting Holes porting surface of the workbench using the dimensions illustrated . When mounting table saw without a vacuum hookup to the base , an opening must be made in the workbench using the dimensions illustrated , so the sawdust can fall away from the Saw base area . % _ _ . _ - _ _ " C " Clamp Workbench Mounting Using " C " Clamps An alternative method of securing your table saw is to fasten the saw base with " C " clamps . 1 . Follow instructions for mounting to workbench , substi - tuting " C " clamps in each recessed mounting screw Iocalion . 2 . Securely clamp saw to workbench using three or 10ur " C " clamps , as shown . Supporting surlace where saw is to be mounted should be examined carefully after mounting to insure that no rnovement can occur during use . If any tipping , sliding or " C " Clamps Recessed Mounting walking is noted , secure the workbench or cabinet before ( Front and Rear ) Screw Location operating the table saw . Diagram of Clamping Table Saw to Workbench Cabinet or Legset Mounting Using Hardware - - 20 " 1 / 2 " ' - - " - - - _ I 3 / 8 " Dia . " - " I " - 2 - 1 / 2 " When mounting table saw to a cabinet or legset and using 2 - 7 / 16 " , a vacuum hookup , holes should be drilled through a 3 / 4 " thick plywood base using the dimensions illustrated . When mounting table saw without a vacuum hookup to T T the base , an opening must be made in the plywood base using the dimensions illustrated , so the sawdust can fall . 21 " 16 1 / 8 " away from the saw base area . Opening _ I WARNING : Never clamp the table saw directly to a II legset . The saw could fall . You could be badly cut . if vacuum | is not | O used l - . _ - - - 16 - 9116 " _ I - , = _ - - 2 " ( Front of Table Saw Diagram of Cabinet Mounting Holes 18
Page: 19

1 . From the loose parts find the following pads . Item Description Qty A Leg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1 Top Front and Rear Brace ( 18 " long ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1 2 Bottom Front and Rear Brace ( 22 " long ) . . . . . . . . . . . . . . . . . . . . . . 2 3 Top side brace ( 17 - 1 / 2 " long ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 4 Bottom side brace ( 22 - 1 / 2 " long ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 5 Leg Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 A 6 Bag of Loose Parts Containing the Following : Bolt carriage , 5 / t 6 - 18 x 5 / 8 " long . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 A Hex Nuts , 5 / 16 - 18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Hex Head Screws . 5 / 16 - 18 x 2 - 1 / 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Lockwashers . 5 / 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Front and Rear 3 5 / 16 - 18 x 5 / 8 " Long Bolt Carriage Right and Left Sides © © 5 / 16 In . External 5 / 16 - 18 Lockwasher Hex Nut 5 4 5 / 16 - 18 x 2 - 1 / 2 " NOTE : Letter and number identifiers are stamped into parts . Hex Head Screw WARNING : For your own safety , turn switch " OFF " and remove plug from power source outlet before mounting power tool onto leg set . Assembly 1 . Install one leg pad onto bottom of each leg . 2 . Assemble front and rear sections first by inserting screws through legs then through braces . Braces are always inside of legs and top brace flanges . Shorter side of braces are always up . Finger tighten screws and nuts as adjustment Front may be necessary later . Assemble front and rear sections as Side shown . Pay particular attention to the hole and screw pat - terns as shown . . . . . . 3 . Assemble side braces to front and rear sections of leg set 4 . Hardware to mount the power tool to the leg set is supplied . W 5 . After the power tool is mounted to the leg set you may then shift the leg set to adjust for a slightly unlevel floor . Then securely tighten all hardware . Top View Use Outermost Holes for Table Saws ( Shaded Areas ) 19
Page: 20

Getting to Know Your Table Saw / 1 1 Blade Guard / / / 12 Table insert / 6 Blade Tilt 10 Rip Fence _ ' 4 Table 3 Miter Gauge ( stored position ) 7 Handwheel / 1 On - Off Switch Rip Fence Storage _ " _ 5 Base Overload Protection 8 Blade Tilt Scale I Wrench Storage Ejection Port ge on Non - thru Cuts 2O
Page: 21

1 . On - Off Switch . CAUTION : Before turning switch " ON " , make sure the blade guard is correctly installed and operating properly . . V = leOn - Off Switch has a locking feature . This feature is intended to help prevent unauthorized and possible haz - ardous use by children and others . 2 . Overload Protection WARNING : When positioning fence for maximum Your saw features an overload relay reset button , If the rip , make sure end of fence head is even with the motor stops running or fails to start ( due to feed pressure edge of the table . Fence cannot be locked securely too fast dull blade or low voltage ) , turn switch " OFF " . beyond the edge of the table . The workpiece could Unplug the saw . Let the motor cool three to five minutes bind and kickback . and push the reset button , which resets the overloaded 11 . Blade Guard device and allows you to turn the saw back on . Use the sawblade guard , spreader and anti - kickback pawls for any thru - sawing ( whenever the blade comes position , and the plug removed from the power I ' through the top of the workpiece ) . Make sure the anti - source while the cool down takes place to prevent II I WARNING : The on / off switch should be in the off . kickback pawls work properly . Make sure the spreader is accidental starting when the reset button is pushed in line with sawblade . ( See page 10 - 11 ) 3 . Sawdust Ejection Port To remove the guard for special operation , loosen wrng Your table saw is equipped with a vacuum hookup . This nut and slide the spreader up . Do not disturb the setting feature will allow you to attach any standard 2 - 1 / 2 inch of the spreader bracket . diameter wet / dry vacuum hose into the hole provided for Whe _ replacing the guard , slide spreader down over tile convenient sawdust removal , spreader bracket . Hand tighten wing nut securely . 12 . Table insert Is removable for removing or installing blade or other cut - ignite sawdust . Even if saw is connected to vac - I WARNING : Sawdust can clog motor . Motor could uum , blow out sawdust regularly . ting tools . WARNING : For your own safety turn switch " OFF " I _ Table and remove plug from power source before remov - _ ovides large working surface to support workpiece . ing insert . t 5 . Base To remove the insert . Supports table . For additional stability , holes are pro - A . Lower the blade below the table surface . vided in base to bolt the saw to a workbench or stand B . Raise blade guard . 6 , Blade Tilt Lock Lever C . Remove insertscrews and lift insertfrom pocket in table Clamps the tilt mechanism alter the blade is adjusted to WARNING : To avoid injury from a thrown workpiece , desired position . Use handwheel as a lever to tilt blade . blade parts , or blade contact , never operate saw with - 7 . Handwheel out the proper insert in place . Use the sawbiade Elevates or lowers the blade . Also used as a lever to tilt insert when sawing . Use the dado / molding head the blade from 0 to 45 degrees . insert when using a dado blade or moldin _ l head . 8 . Blade Tilt Scale 13 . Miter Gauge Shows the degree the blade is tilted , Head can be locked in desired position for cross cutting 9 . Wrench Storage or mitering by tightening the lock knob . Always securely Conveniently stores shaft and arbor nut wrenches , lock it when in use 10 . Rip Fence Notches are provided in the miter gauge for attaching an Exclusive self - aligning , quick - set rip fence can be easily auxiliary facing to make it easier to cut longer pieces . Be moved or locked in place by simply raising or lowering sure facing does not interfere with the proper operation of lock handle . Holes are provided in the rip fence for the sawblade guard . attaching a wood facing . Select a piece of smooth straight wood approximately 3 / 4 inch thick , at least as along as the rip fence , and at least 7 - 1 / 2 " wide ( high ) to permit clamping of leatherboards . _ ttach it to the fence with two round head # 10 wood brews 1 - 5 / 8 " long . Select a suitable piece of smooth straight wood . drill two holes through it and attach it with screws . NOTE : When bevel crosscutting , attach facing so that it extends to the right of the miter gauge and use the miter gauge in the groove to the right of the blade . 21
Page: 22

Work Feed Devices Slightly Less Than Thickness Belore cutting any wood on your saw , study all of the " Basic Saw Operations " found on pages 23 through 33 . . , _ 3 / 4 " Of Workpiece UpTo As you learn new table saw woodworking techniques , you'll see that many types of cuts need different support and feeding devices , known as jigs or lixtures . They can help you make cuts more accurately . By helping to steady the workpiece and keep you away from the blade , they can helpyou safely use your saw for certain cuts . Many people custom build their own jigs and fixtures . NOTE : All dimensions in inches Materialfor Push Block Jigs and fixtures are often designed for a particular cut _ You can use your table saw to easily make many jigs and _ - _ At Least12 " _ , . lixtures . To get you started we've included instructions for some simple ones . After you have made a fe _ - prac - tice cuts . make up these jigs before starting any projects . 3 / 8 " Thick Plywood At Least Make the push stick first . Base 5 - 5 / 8 " Push Stick Make the push stick using a piece of 1 x 2 . ( See drawings At Least 12 " top right for dimensions and shapes . ) Push Block 3 / 4 " Thick Plywood There are any number of ways to properly cut your work - At Least Handle 5 - 518 " pieces to make a push block . The following steps describe one way you can make a push block . Making the base : • Start with a piece of 3 / 8 inch plywood at least 5 - 5 / 8 Cutting Out the Base inches wide or wider and 12 inches long or longer . - Make two ripcuts . Perform the first ripcut along the - , _ - - _ 2 - 1 / 2 " ( save ) 3 / 8 " 7 side making a 3 / 8 " wide strip . Next ripcut the 3 / 8 " _ 1 4 th Cut 1 st Cut T plywood to a width of 5 - 1 / 8 " . • Crosscut the 3 / 8 " plywood to 12 " long , - Crosscut a 2 - 1 / 2 " piece off the 3 / 8 " wide by 3 / 8 " thick strip and save this short piece for later . 2 nd Cut • The next cuts will create the 3 / 8 " by 9 - 1 / 2 " notch in the - - - _ 12 " , . - I base . Mark the long edge of the board 2 _ 1 / 2 " from one end . Make a crosscut into the edge on the mark , stop - ping about 3 / 4 " into the board . Set the saw and rip the Creating the Notch width to 4 - 3 / 4 " along the same edge as the stopped crosscut . Stop the ripcut where the two cuts intersect . Turn off the saw and remove the base piece . The base should now measure as shown . I 1 st Cut 2 nd Cut II Finished Base = _ 12 " - I I - 3 / 8 " 5 - 1 _ " these Edges Must Be Parallel 22
Page: 23

Makingthe handle : * Miter crosscut a piece of 3 / 4 inch thick plywood to J _ _ shape and size shown : NOTE : The mitered corners can be any size that looks like the drawing ( about t - 1 / 2 " by 1 - 1 / 2 " ) . 1 - 1r " / l _ _ . S " 1 - 1 / 2 Putting it Together • Using good quality woodworking glue , glue the 3 / 8 " x 3 / 8 " x 2 - 1 / 2 " piece strip saved earlier to the base as shown . 12 = IMPORTANT : Do not use nails or screws . This is to pre - vent dulling of the sawblade in the event you cut into the push block . - Position the handle at the center of the plywood base as shown Fasten them together with glue and wood Glue only Join _ screws . IMPORTANT : Make sure the screw heads do not stick out from the bottom of the base , they must be flush or recessed . The bottom must be flat and smooth enough to slide along the auxiliary fence you are now ready to make . Flush Or Recessed 1 _ Finished Push _ ndle Auxiliary Fence Making the base : _ - 3 / 8 " Plywood Base ° Start with a piece of 3 / 8 inch plywood at least 5 - 1 / 2 Cutting Out the Base inches wide or wider and 16 inches long or longer . • Cut the piece to shape and size shown : i ' _ 16 _ Making the side : o Start with a piece of 3 / 4 inch plywood at least 2 - 3 / 8 3 / 8 " Thick Plywood Base inches wide or wider and 16 inches long or longer , o Cut the piece to shape and size shown : Putting it together : Cutting Out the Side ° Put the pieces together , as shown : iMPORTANT : Make sure the screw heads do not stick out from the bottom of the base , they must be flush or I 3 / 4 " Thick Plywood Side 12 - 3 / a " recessed . The bottom must be flat and smooth enough to rest on the saw table without rocking . f 3 / 4 " Plywood Finished Auxiliary Fence . . . . . _ _ , . . _ 4 - 314 / f _ 318 " Plywood _ I This Edge and / / 7 / II 1 23
Page: 24

Safety Instructions for Basic Saw Operations Before Each Use Inspect your work area . • Keep work area clean . Inspect your saw . ° Cluttered areas and benches invite accidents . Floor = To avoid injury from accidental starting , turn the switch must not be slippeR / from wax or sawdust . off . unptuq the saw . and remove the switch key before ° To avoid bums or other fire damage , never use the raising or removing the guard , changing the cutting tool . changing the setup , or adjusting anything . saw near flammable liquids , vapors or gases . - Check for alignment el moving parts , binding of mow • To avoid injury , don't do layout , assembly , or setup ing parts , breakage of pads . saw stability and any work on the table while blade is spinning . It could cut othe { conditions that may affect lhe way tile saw or throw anything hitting the blade . works Plan your work , , ! I any part is missincL bent or brek _ n in any way , or any - Plan ahead to protect your eyes . hands , face . ears . electrical part does no ! work properly , lure the saw off • Use The Right Tool . Don't force tool or attachment to and unplug the saw do a job it was not designed for - Heptace darnaged or missing palls before using the Dress for safety . saw again . • Do not wear loose clothing , gloves , neckties or jeweh ¥ - Use the sawblade guard , spreader and anti - kickback ( rings , wrist watches } . ] hey can get caught and draw pawls for any thru - sawing ( whenever the blade comes you inlo mov | ng parts . througl _ lhe lop of the workpieceL Make sure lhe anti - • Wear nonslip footwear . kickback pawls work properly . Make sure the spreader • Tie back long hair _ is in line with sawblade ( See page 10 - 1 ! ) . • Roll long sleeves above the elbow . , , Make sure all clamps and locks are tighl and no parts • Noise levels vary widely . To avoid possible hearing have any excessive play . damage , wear ear plugs or muffs when using table - Remove adjusting keys and wrenches . Form a habit of saw for hours at a time . checking for and rernoviag keys and adjusting • Any power saw can throw foreign objects into the wrenches from table top before turning it on . eyes . I his can result in permanent eye damage . Wear To avoid injury from jams , slips or thrown safety goggles tnot glasses ) thal comply with ANSI pieces ( kickbacks or throwbacks ) Z87 . 1 ( shown on package ) . Everyday eyeglasses have Inspect your blade . only impact resistant lenses . ] hey are not safety glasses . Safely goggles are available at Sears retail • Choose the r | ghI blade or cutting accessory for the stores . Glasses or goggles not in compliance with matenal and the type of cutting you plan to do . ANSI Z87 . 1 could seriously hurt you when they break . - Never use grinding wheels , abrasive cutolf wheels . friction wheels lrnetal cutting blades ) wire wheels or buffing wheels , lhey car _ fly apart explosively . " Choose arid insuecl your cutting tool carelully : ] - o avoid cutting loci lailure and | brown shrapnel ( broken pieces of blade ) , use only 10 inch or smaller blades or ether c | . Jtt | ngt iDOlS marked tar speeds of • For dusty operalions , wear a dust mask along with 5000 rprn or hiqher . safety goggles . • Always use unbroken balanced blades designed to Inspect your workpiece . fit this saw's 5 / 8 inch arbor . • Make sure there are no nails or foreign objects in the - When thru - sawing ( making cuts where the blade part of the workpiece to be cut . coffees through lhe workplece top ) , always use a 10 - When cutting irregularly shaped wo | kp | eces , plan your inch diameter blade . [ his keeps the spreader in clos - work so it will nol slip and pinch the blade : est to the blade . ° A piece of molding for example , must lie flat or be held - Do not over tighten arbor nut . Use arbor wrenches to by a fixture or jig that will not let it twist • rock or slip " snug " it securely . while being cut . Use ] igs or fixtures where needed to - Use only shard blades witl _ properly set teeth . Con - prevent workpiece shifting . sult a professional blade sharpener when in doubt . • Use a different , better suited type of tool for work that - Keep blades clean of gum and resin . can't be made stable . • Never use the saw without the proper blade insert . 24
Page: 25

Avoid accidental starting . Plan your cut . , M _ , _ kesure switch is " OFF " before plugging saw into a , To avoid kickbacks and ti _ rowbacks - when a part or all power ouiie _ of the workpiece brads on lt _ e biade and is thrown vio - lently back toward the front of the saw : Whenever Sawblade Is Spinning - Never cut freehand . Always use esther a rip fence , I WARNING : Don't allow familiarity ( gained from fre - ] miter gauge or fixture to position and guide the work , qaent use of your table saw ) cause a careless mis - | so it won't twist or bind on the blade and kickback . take , Always remember that a careless fraction of a | - Make sure there's no debris between the workpiece second is enough to cause a severe injury . | and its supports • Before actually cutting with the saw , wa ' ; ch it while it • Use extra cautJo _ with large , very " srnatl or awkward runs for a short while . If it makes an u _ fami _ iar noise or workpieces : vibrates a lot , stop immediately . Turn the saw off . ° Use extra suppoMs ( tables , saw horses , blocks , etc . ) Unplug lhe saw . Do not rested until finding and cor - for any workpieces large enough to tip when not held recting the problem down to the table top . Never use anothe _ person as a • Make sure the top ot the arbor or cutting tool turns substitute Iora table extension , or as additional sup - toward the front of the saw . pod for a workpiece that is longer or wider than tt _ o Keep children away basic saw table , or to help feed , support or pull the , , Kee l ) all visitors a safe distance from the table saw . workpiece , , , Make sure bystanders are ciear of the tabie saw and - Never confine the piece befflg cut off , thai is , the piece workpiece . not against the fence , miler gauge or fixture . Never Don't force tool . hoid it , clamp it , touch it , or use lenglh stops against iL It must be free 1o r'nove . If confined , it could get - Letthe blade reach lullspeed before cutting . wedged against the blade and cause a kickback or - it will do the job better and safer at its designed rate . throwback , , , Feed the workpiece into the saw only fast enough to Iet , , Never cut more than one workpiece at a time . the blade cut without bogging down or binding . - Never lure your table saw " ON " before clearing every - Before freeing jammed material , thing except the workpiece and related support = Turn switch " OFF " . devices off the table . - Unplug the saw , Plan the way you will push the workpiece through . • Wait for all moving parts to stop , • Never pull the workpiece through . Start and Iinist _ - Check blade , spreader and lence for proper alignment the cut from the front el the table saw . before starting again , • Never put your fingers or hands in the path of the To avoid throwback of cut off pieces . sawblade or other cutting tool . - Use the guard assembly , ° Never reach in back of the cutting tool with either To remove loose pieces beneath or trapped inside hand to hold down , support the workpiece , remove the guard . wood scraps , or for any other reason . - Turn saw " OFF " . - Avoid hand positions where a sudden slip could cause fingers or hand to move into a sawblade or other cut - • Remove switch key , ting tool , • Wait for blade to stop before lilting the guard . • Don't Overreach , Always keep good footing and bal - Before leaving the saw . ance . . Tum the saw off . • Push the workpiece against the rotation of the blade . - Wait for blade to stop spinning . Never feed material into the cutting tool from the rear - Unplug the saw . of the saw . - Make workshop child _ proof . Lock the shop , Disconnect Always push the workpiece all the way past the saw - master switches . Rernove the yellow switch key . Store blade . it away from children and others not qualified to use • As much as possible , keep your face and body to one the tool . side of the sawbtade , out of line with a possible kick - back or throwback . • Set the cutting tool as low as possible for the cut you're planning , 25
Page: 26

Basic Saw Operations NOTE : The space between the miter gauge bar and the Using the Miter Gauge groove in the table is held to a minimum during manufac - The miter gauge is used when crosscutting , miter cutling , turing . bevel cutting , compound miter cutting , dadoing and when For maximum accuracy when using the miter gauge , rabbeting across the end of a narrow workplece . always favor one side of the groove in the table , in other For observe words , don't move the miter gauge lrom side to side while cutting but keep one side of the bar riding against the following safety precautions in addition to the I WARNING : ' your own safety , always one side of the groove . safety instructions of pages 2 , 3 , 4 , 5 , 23 & 24 . NOTE : Glue a piece of sandpaper to the face of the miter Additional Safety instructions for Crosscutting gauge head . This will help prevent the workpiece from Before Starting : " creeping " while it is being cut . • Never use the rip fence when crosscutting . An auxiliary wood facing attached to the miter gauge I WARNING : To avoid blade contact or kickback , I hold miter gauge properly . can help prevent workpiece twisting and throwbacks . When using the miler gauge in the left hand groove , hold Attach il to the holes provided . Make the facing long the workpiece firmly against gauge head with your left enough and big enough te support your work . Make hand , and grip the lock knob with your right hand . sure , however , it will not interfere with the sawblade When using the miter gauge in the right hand groove . guard . hold the workpiece with your right hand and the lock knob • Use jigs or fixtures to help hold any piece too small to with your left hand . extend across the full length of the miter gauge face Miter gauge head is locked in position for crosscutting or during the cut . This lets you properly hold the miter mitering by tightening the lock knob , Always lock it gauge and workpiece and helps keep your hands securely when in use . away lrem the blade . Holes are provided in the miter gauge for attaching an ° Use extra supports such as plywood clamped to a auxiliary facing to make it easier to cut long pieces . Make sawhorse for workpieces that are long and heavy sure facing does not interfere with the proper operation of enough to tip or that tend to raise the miter gage from the sawblade guard . the groove in the table , never use another person as a Select a suitable piece of smooth straight wood . drill two substitute for a support or to help feed or pull the work - holes through it and attach it with screws . piece . While cutting : Plywood Clamped • To avoid blade contact , always hold the miter gauge to Sawhorse as shown in this section . \ \ \ Crosscutting \ A crosscut is known as cutting or shaping operation made across the width of a workplece . The graduations on the miter gauge provide accuracy for average woodworking . In some cases where extreme accuracy is required , when making angle cuts , for exaM - pie , make a trial cut and then recheck it with am accurate sq uare , or protractor . Always Support If necessary , the miter gauge head can be swiveled Long Workpieces slightly to compensate for any inaccuracy . 26
Page: 27

Repetitive Crosscutting Repetitive cutting is known as cutting a quantity of pieces the same length without having to mark each piece . • When making repetitive cuts from a long workpiece , make sure it is supported . WARNING : Never use the rip fence as a length stop because the cutoff piece could bind between the fence and the blade causing a kickback . 1 . When making repetitive cuts , clamp a block of wood 3 " long to the table at desired length to act as a length stop . workpiece , when clamping the block , make sure that the end of the block is well in front of the saw - I WARNING : To avoid kickback from twisting the I blade . Be sure it is clamped securely . 2 . Slide the workpiece along the miter gauge until it touches the block . . . hold the workpiece securely against the miter gauge . 3 . Make the cut . . . tum the saw off . . . rernove the piece after the blade has stopped and before cutting the next piece . Miter Crosscutting Miter cutting is an angle cutting operation made across the width of the workpiece . Follow the same procedure as you would for crosscutting . • Adjust the miter gauge to the desired angle , and lock it . = The miter gauge may be used in either of the grooves in the table . Make sure it is locked . • When using the miter gauge in the left hand groove , hold the workpiece firmly against the miter gauge head with your left hand , and grip the lock knob with your right hand . • When using the miter gauge in the right hand groove , hold the workpiece with your right hand and the lock knob with your left hand . Bevel Crosscutting Bevel crosscutting is the same as crosscutting except that the wood is also cut at an angle . . . ether than 90 ° with the bottom flat side ot the wood . - Adjust the blade Io the desired angle . • Always use the miter gauge in the groove to the right of the blade . It cannot be used in the groove to the left because the blade guard will interfere . Hold the work - piece with your right hand and the lock knob with your left hand . 27
Page: 28

Basic Saw Operations ( continued ) Compound Miter Crosscutting Compound miter cutting is a combination of miter cutting and bevel Crosscutting . The cut is made at an angle other than 90 ° to both the edcle and the bottom fiat side of the wood . " Adjust the miter gauge and the blade to the desired angle , . . Make sure miter gauge is locked . - Always usethe miter gauge in the groove to the right of the blade . It cannot be used in the groove to the left because the blade guard will interlere . Hold the work - piece with yourright hand and the lock knob wilh your left hand . Using the Rip Fence Additional Safety Instructions for Rip Cuts Before starting : o Never use the miter gauge when ripping Ma ke From 314 " Thick Solid Wood • Use a push stick whenever the fence is 2 or more , - 24 " = 1 inches from the blade . Kerfs About ! _ = _ • When thru - sawing , use an auxiliary fence and push 5 / 16 " Apart _ _ . _ _ block whenever the fence must be between 1 / 2 and 2 8 " inches from the blade , ' I - - _ L _ ra , n • Never thru - saw rip cuts narrower than 1 / 2 inch . ( See 4 - 1 / 2 _ 5 " - _ Featherboard " Basic Saw Operations - Ripping and Bevel Ripping " section ) • Never rip anything shorterthan 10 " long . • When using a push stick or push block , the trailing end of the werkpiece must be square , A push stick or push block against an uneven end could slip ofl or push the workplace away from the fence • A featherboard can help guide the workpiece , ( see " Basic Saw Operation - Using Featherboards for Thru - Sawing . " section ) ° Always use featherboards for any non thru - sawtng rip type cuts . ( see " Basic Saw Operations - Using Feather - boards for Non Thru - sawing " section ' ) • To avoid kickbacks and slips into the blade make sure the rip fence is parallel to the sawblade • Before thru - sawing , check the anti - kickback pawls , the pawls must stop a kickback once it has started . Replace or sharpen anti - kickback pawls when points become dull . • Ptastic and composition ( like hardboard ) materials may be cut on your saw . However , since these are usually quile hard and slippery , the anti - kickback pawls may not stop a kickback . Therefore . be especially carelul in your set - up and cutting procedures . While Thru - sawing : • To avoid kickbacks and slips into the blade , always push forward on the section of the workpiece between the sawblade and the rip fence . Never push forward on the piece being cut off . 28
Page: 29

Ripping Always Support Long Ripping is known as a cutting operation along the length Workpiece _ / of the workpiece . Position the fence to the desired width of rip and lock in place . Before starting to rip , be sure : 1 . Rip fence is parallel to sawblade . 2 . Spreader is properly aligned with sawblade . 3 . Anti - kickback pawls are functioning properly . When ripping long beards or large panels , always use a work support . A simple support can be made by clamping a piece of plywood to a sawhorse . Blade Path WARNING : To avoid kickback , push forward only I on the part of the workpiece that will pass between I StoF the blade and the fence . I Here Keep your hands out of the blade path . Feed the workpiece by pushing forward only on the part of the workpiece that will pass between the blade and the fence . Stop the thumb of your outside hand at the lront edge of the table . Finish the cut with the appropriate push stick or push block . Once the trailing end is on the table : When " width of rip " is 2 " or wider , use the push stick to finishthe work all the way past the blade . Width of Rip 29
Page: 30

Basic Saw Operations ( continued ) When " width of rip " is narrower than 2 " , the push stick cannot be used because the guard will interfere . Use the auxiliary fence and push block for this ripping operation . Attach auxiliary fence to rip fence with two " C " clamps . Auxiliary Work Support / Fence Feed the workpiece by hand along the auxiliary fence until the end is approximately 1 " past the front edge of the table , Continue to feed using the push block . Hold the workpiece in position and install the push block by sliding it on top of the auxiliary fence / work support . This may raise the guard . Push Block ' \ con | a _ t never perform thru - saw cuts narrower than 112 I WARNING : To avoid injury from blade wide . Narrow strips thicker than the auxiliary fence / work sup - eort may enter the guard and strike the baffle . Carefully raise guard only enough to clear the workpiece . Use push block to complete cut . Baffle Bevel Ripping When bevel ripping material 6 " or narrower , use fence on the right side of the blade only . This will provide more space between the fence and the sawbtade for use of a push stick . If the fence is mounted to the left , the saw - blade guard may interfere with proper use of a push stick . 3O
Page: 31

Using Featherboards for Thru - Sawing " C " Clamps Featherboards are not employed for thru - sawing opera - t _ ns when using the miter gauge . Work Supports Featherboard _ atherboards are used to keep the work in contact swith . _ e fence and table as shown , and to help stop kickback Add a 7 - 1 / 2 " high flat lacing board to the full length of the fence . Mount featherboards to fence and table as shown . I WARNING : Make sure the featherboard against the edge presses only on the uncut portion ( in front of the blade ) . It might otherwise pinch the blade in the kerr and cause a kickback . Before starting the operation ( turn switch " OFF " and lower blade or cutter below table surface ) : \ Featherboard • Install featherboards so they exed pressure on the workpiece ; be positive they are securely attached . " C " Clamps Front of Saw • Make sure by trial that the teatherboards will stop a kickback if one should occur before performing this operation . Before starting your cut : Push Stick ° Slide the workpiece in between the featherboards the same way you'll feed it in for the cut . ° Pull back on the workpiece , The piece should be harder to pull back than it was to push forward . ° Adjust your featherboards and repeat the trial , as needed . _ cuotll . ow the applicable ripping instructions to make the Resawing Resawing is a thru - sawing cut made by ripping a piece of wood through its thickness . WARNING : Do not attempt to resaw bowed or warped material . It can't be properly supported , it could kickback or bind . NOTE : To resaw a piece of wood wider than 3 " . it will be necessary to remove the blade guard and use the auxil - iary fence / work support . ( See " Workfeed Devices " on page 2t - 22 ) . Auxiliary Fence Workpiece Clamp the auxiliary fence / work support to the table so that the workpiece will slide easily without binding between the two fences and it will not tilt or move side - ways . Do not clamp directly to the bottom edge of the table because the " swivel " of the clamp will not gdp properly . Place a small block of wood between the bottom edge of the table and the " C " clamp WARNING : For your own safety \ 1 . Do not " Backup " ( reverse feeding ) while resaw - \ Fence ing because this could cause a kickback . Small Block of Wood " 2 . Make first pass to a depth slightly more than one half the width of the board ; keep same face of board against fence for second pass . R _ / ARNING : For your own safety , install blade guard immediately upon completion of the resawing operation . 31
Page: 32

Basic Saw Operations ( continued ) , Using Featherboards for Non Thru - Featherboard Sawing " C " Clamp " C " Clamp Featherboards are not employed during non thru - sawing \ / / operations when using the miter gauge , Use featherboards for all other non thru - sawing opera - tions ( when sawblade guard must be removed ) . Feather - boards are used to keep the work in contact with the fence and table as shown and to stop kickbacks . Add a 7 - 1 / 2 " h _ ghflat facing board to the full length of the Iencm Mount featherboards to fence and table as shown , so that leading edges of featherboards will support work - Front of Saw piece until cut is complete , and the workpiece has been pushed completely past the cutter ( sawblade . dado - \ head . etc , ) with a push stick , as in ripping , • Featherboard " C ' " Clamps Before slarting the operation ( turn switch " OFF " and lower blade or cutter below table surface ) : - Install leatherboards so they exert pressure on the workpiece : be positive they are secure . • Make sure by trial the featherboards will stop a kick - back if one should occur before performing this opera - tion . Before starting your cut : - Slide the workpiece in between the featherboards the same way you'll feed it in for the cut . • Pulf back on the workpiece . The piece should be harder to pull back than it was to push forward . - Adjust your featherboards and repeat the trial , as needed . - Follow the applicable ripping instructions to make the cut . Back of Saw blade , blade guard , spreader and blade insert as soon as the non thru - sawing operation is complete . Dadoing Instructions for operating the dado head are contained in booklet furnished with the dado [ lead The arbor on the saw is only long enough so that the wid - Loose Collar est cut that can be made is 9 / 16 " wide . Saw Arbor , _ It is not necessary to install the outside loose collar before screwing on the arbor nut , Make sure the arbor nut is tight and at least one thread on the arbor sticks out past the nut . " Arbor Nut Always use dado insert listed under recommended accessories . When using the dado head . it witl be necessary to remove the blade guard and spreader . Use caution . Use miter gauge , fence , featherboards or push sticks as required . Remove Sawblade and Install t WARNING : For your own safety , always replace the Dado Head and Dado Insert blade , blade guard , spreader and blade insert when you are finished dadoing . 32
Page: 33

Rabbeting Second Cut Rabbeting is known as cutting out a section of the corner of a piece of material , across an end or along ar ] edge . To make a rabbet requires cuts which do not go a ] ! the Rabbet way through the material . Therefore , the b _ ade guard must be removed . 1 . Remove blade guard . 2 . For rabbeting along an edge ( long way of workpiece ) as shown , add facing fo rip fence approxir * natetY as high as the workpiece is wide . Adjust rip fence and First Cut blade to required dimensions ; then make first Gilt with board flat on table as you would with any rip ( type ) cut ; make second cut with workplace on edge . Follow all precautions , safety instructions , and operational Rabbeting Along the Edge instructions as for dpping , or rip type operations , including featherboards and push stick , etc . 3 . For rabbeting across an end , for workpiece 10 - 1 / 2 " Second Cut Etc . and narrower , make the rabbet cut with the board flat on the table . Using the miter gauge fitted with a faci _ g , follow the same procedures and instructions for cross cutting making successive cuts across the width of the First Cut workpiece to obtain the desired width of cut . Do not use the rip fence for rabbeting across the end . Rabbet WARNING : For your own safety , install blade guard I immediately upon completion of rabbeting operation . I Some rabbet outs can a _ so be made in one pass of th , e Rabbeting Across the End workplace over the cutter using a dado head . Ploughing or Molding Ploughing is grooving with the grain the long way of the workpiece , using the fence . Use featherboards and push sticks as required . Molding is shaping the workplace with the grain the long Ploughing way of the workpiece , using the fence . Use feather - boards and push sticks as required . WARNING : For your own safety , always replace the I blade , blade guard , spreader and blade insert when I you are finished . J Molding 33
Page: 34

Installation and Operation of Molding Head To get fu ! | arbor nut engagement with the arbor threads , this saw requires a special molding head mounting Back of Saw arrangement . Always arrange and mount the molting head as shown . Instructions for assembling and operat - ing the molding head are contained in a booklet furnished with the molding head . Follow molding head installation instructions for table saws , except use the loose blade collar supplied with the saw instead of the spacer washer supplied with the mold - ing head . Do NOT use the spacer washer provided with the molding head . Always position the bose blade collar as shown . Always use the moldfng insert listed under recom - mended accessories . When using the molding head it will be necessary to remove the blade guard and spreader . Use caution . Use miter gauge , fence , featherboards , or push sticks , etc . , as required . WARNING : For your own safety , always replace the BlaL : ° _ ° ella Front of Saw blade , blade guard , spreader and blade insert when you are fin ished molding . Molding Head Mou nting Maintaining Your Table Saw Maintenance Anti - Kickback Pawls and remove plug from power source outlet before always sharp . To sharpen : I WARNING : For your own safety , turn switch " OFF " maintaining or lubricating your saw . I Make sure the teeth of the anti - kickback pawls are 1 . Remove blade guard . • Do not allow sawdust to accumulate inside the saw . 2 . Rotate pawl toward rear el spreader so that teeth are above top of spreader . Frequently blow out any dust that may accumulate inside the saw cabinet and the motor . 3 . Hold spreader with left hand and place pawl over cor - • Clean your cutting tools with a gum and pitch remover . ner of workbench as shown . • The cord and the tool should be wiped with a dry clean 4 . Using a srnall round file . ( smooth cut ) sharpen the teeth . cloth to prevent deterioration from oil and grease . • A coat of automobile - type wax applied to the table will 5 . Reinstall blade guard . help to keep the surface clean and allow workpieces to slide more freely . • If the power cord is worn , cut , or damaged in any way , have it replaced immediately . IMPORTANT : Certain cleaning agents and solvents can nt , - Kmkback damage plastic paris . Some of these are : gaso ne , car - bon tetrachloride , chlorinated cleaning solvents , ammo - nia and household detergents which contain ammonia . Avoiding use of these and other types of cleaning agents will minimize the possibility of damage . Use cleaners suitable for prescription glasses or liquid dishwashing detergent and water . should be attempted only by a trained repairman . Contact the nearest Sears store for service . Use only identical replacement parts . Any other parts I may create a hazard . 34
Page: 35

Lubrication The saw motor bearings and gear case have been packed at the factory with proper lubricant and require no additional lubrication . The following parts should be oiled occasionally with SAE no . 20 or no . 30 engine oil . 1 . Elevation screw threads and pivot nut . 2 . Elevation bracket pivot points . 3 . Bearing points in blade guard , miter gauge and rip fence assemblies ( as shown by * ) . Sears Recommends the Following Accessories Item Cat . No . Sears may recommend other accessories not listed in manual . Saw Bmades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Catalog Dado / Molding Head Insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 29971 See your nearest Sears Store or Power and Hand Tool 5 - 5 / 8 " Molding Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Catalog Catalog for other accessories . 6 " Dado Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Catalog Do not use any accessory unless you have received and read complete instructions for its use . WARNING : Do not use adjustable ( wobble ) type dados or carbide tipped dado blades on this saw , this saw . Using other accessories may be danger - Maximum dado width is 9 / 16 inch . i WARNING : Use only accessories recommended for ous , Steel Leg Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 22235 Caster Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 22222 9 - 22221 35
Page: 36

Troubleshooting WARNING : To avoid injury from accidental start , turn switch " OFF " and always remove plug from the power source before trouble shooting . TROUBLE I PROBABLE CAUSE REMEDY I Excessive vibration 1 . Blade out of balance . 1 . Discard blade and use a different blade . Cannot make square cut 1 . Miter gauge not adjusted properly . 1 . See " Adjustments " section " Miter gauge " when crosscutting Cut binds , burns or 1 . Dull blade or improper tooth set . t . Sharpen or replace blade . stalls motor when rip - 2 . Warped board 2 . Make sure concave side is facing " down " , feed ping . slowly . 3 . Rip fence not parallel to blade . 3 . See " Assembly " section , " Aligning Rip Fence . " 4 . Spreader out of alignment 4 . See " Assembly " section , " Installing Blade Guard . " Bevel cut not true 90 ° or 1 . Stop screw not properly adjusted . 1 . See " Adjustments " section , " Blade tilt , or square - 45 ° ness of blade to table . " Elevating ha ndwhee ] 1 . Sawdust on threads of elevating 1 . See " Maintenance and Lubrication " section . hard to turn I screw . 2 . Don't over tighten handwheel . Check to see if 12 . Over tightening handwheel when Key No . 33 on page 38 is binding . , raising blade . Excessive blade wobble 1 . Blade has excessive wobble . 1 . Replace blade . ( causes oversize kerr 2 . Blade loose . 2 . See " Installing Sawblade " section . and unsmooth cut . ) Excessive noise 1 . Motor 1 . Have motor checked by Sears Service Center . Motor starts slowly or 1 . Circuit overloaded with lights 1 . Do not use other appliances or motors on the fa Is to deve op fu app lances and other motors . same circuits when using the saw . power . NOTE : A low 2 . Undersize wires or circuit too long . ' 2 . Increase wire sizes , or reduce length of wiring . voltage condition will I See " Motor Specifications and Electrical cause the power output I Requirements " section . of the motorto decrease 3 . General overloading of power 3 . Request a voltage check from the power com - rapidly . For example , a company facility . ( In some sections pany . reduction of 10 % in volt - . of the country , demand for electri - age causes a reduction ' cal powermayexceedthe capacity of 19 % in maximum of existing generating and distribu - [ power output of which tion systems . ) 4 . Installcorrect fuses or circuit breakers . the motor is capable . 4 . Incorrect fuses or circuit breakers ' in power line . 5 . Bad / worn brushes 5 . Have brushes replaced by Sears Service Center . 1 . Motor overloaded . 1 . Do not cut so fast . Feed work slower into blade . Motor overheats . 2 . Improper cooling , ( motor air circu - 2 . Clean out sawdust to provide normal air circula - lation restricted due to sawdust lion through molor . See " Maintenance and Lubri - i accumulating ns de of saw ) . cat on " sect on . Motor stalls ( resulting in 1 . Voltage too low to permit motor to 1 . Request voltage check from the power company . reach operating speed . b ! own fuses or tripped 2 . Fuses or circuit breakers do not 2 . Install proper size fuses or circuit breakers . circuit breakers . ) have sufficient capacity . 3 . Feed rate too fast or dull blade . 3 . Allow motor to cool and reset saw breaker . 1 . Motor overloaded 1 . Don't cut so fast . Feed work slower into blade . Frequent opening of fuses or circuit breakers 2 Fuses or circuit breakers do not 2 . Install proper size fuses or circuit breakers . have sufficient capacity . 3 . Feed rate too fast or dull blade . 3 . Allow motor to cool and reset saw breaker . Fence is hard to slide 1 . Front fence rail surface is dry . 1 . Apply a coat of paste wax to the top , front and - • rear edge of the front fence rail surfaces . 36
Page: 37

Repair Parts , , Parts List for Craftsman 10 " Bench Top Table Saw Model No . 113.221770 Always Order by Part Number - Not Key Number Figure 1 Key No Part No . Description _ i _ / ii , + / iiiii 1 823196 Guard 2 823091 Rivet 3 STD54t025 Nut Hex t / 4 - 20 4 STD551225 Lockwasher , Ext . 1 / 4 5 STD551012 Flatwasher , 17 / 64 x 7 / 16 x 1 / 32 6 823089 Bumper Snap In 7 802612 - 13 : t : Nut , Push 6ram 8 823096 Spring Torsion 9 822450 Pawl , Anti + kickback ! 10 823095 Spacer 11 823098 Spreader 12 STD541625 Nut , Wing 1 / 4 20 13 STD551025 Ffatwasher , 17 / 64 x 5 / 8 × 1 / 32 14 823080 Bracket Asm . , Spreader 15 STD522505 Screw , Hex Hd 1 / 4 + 20 x 1 / 2 16 822489 Bolt , Carriage I / 4 - 20 x 7 / 8 10 17 823079 Support Spreader 18 STD522522 Screw , Hex Hd + 1 / 4 - 20 x 2 - 1 / 4 1D 19 823090 Bracket , Guard Screw Hex Hd ! / 4 + 20 x 1 + 1 / 2 20 STD522515 11 21 823088 Spacer Standard Hardware Item - May be purchased loca ! ly . $ If this part is removed , discard and replace with a new push nut . 17 _ 14 13 37 i II i
Page: 38

Repair Parts Parts List for Craftsman 10 " Bench Top Table Saw Model No . 113.221770 Figure 2 42 4O " 6 J 36 / 13 15 16 18 / 22 27 28 26 38
Page: 39

Repair Paris . . . . Parts List for Craftsman 10 " Bench Top Table Saw Model No . 113.221770 Always Order by Part Number - Not Key Number Figure 2 Key Keyo . No . Part No . Description N Part No . Descriptfon 1 817357 - 1 23 813249 - 132 Screw , Ty " E " M4 x 16 - 12 Pin , Roll 2 822497 Insert , Table 24 823053 Rod , Screw 3 822498 Nut , Speed M4 x 16 25 823050 FD'IResetSwitct _ , w / nut 4 822487 - 1 26 9 - 22255 Screw , Cr - Special 1 " Key , [ ockin 9 5 823170 Table 27 822308 Switch , Locking 6 823023 Scale R . H . 28 STD611007 * Screw . ry " AB ' # _ 0 x 3 : 4 Scale L . H . 29 823010 7 823022 Clamp , Cord 8 823046 30 STD610807 Clamp , Hale Screw , Pan Hd # 8 x 3 ; ' 4 9 STD852004 31 823012 Lockwasher , Ext . M4 Box , Switch 10 56 - 100002 32 823048 Nut , Hex M4 x . 7 Cord w / plug 33 823O94 11 823047 Screw , Cr Flat Hd M3 x . 5 - 7 Grommet 34 823049 12 825803 Foot , Rubber Label , Trim Panel 35 823172 Base 13 STD551025 Washer , 17 / 64 x5 / 8 x 1 / 32 36 823024 14 60545 Outlet , Dust Washer , Nylon 37 46 - 57680 - 3 Screw , M4 x . 7 - 16 15 823042 Nut , Locking 38 822493 Screw , Hex Serr . Flat Hd 16 823041 Knob , Bevel Lock 39 822487 Screw , Cr - Speciat 17 823O44 Spring , Compression 40 823001 Screw . Cr - Specla ! 18 823043 Bolt , Special Screw FUlister Head 41 820816 Wrench . Shaft 19 823086 Wrench . Arbor Nut Knob 42 820815 20 823085 Owners Manual tno ! [ llus SP6048 21 STD541031 Nut , Hex 5 / 16 - 18 trated ) 22 823052 Handwheel , Elevation " Stanard Hardware Item - May be purchased locally 1 " Stock item - May be secure through the hardware department ol most Sears retail stores . WARNING : Service of double - insulated parts . In a double - insulated tool , two systems of insulation are pro - vided instead of grounding . No grounding means is provided on a double - insulated tool nor should a means for grounding be added . Servicing a double insulated took requires extreme care and knowledge of the sys - tem , and should be done by a qualified service personnel . Replacement parts for a double4nsulated tool must be identical to the parts they replace . Your double - insulated tool is marked with the works " ' DOUBLE - INSULATED " and the [ ' _ ( square within a square ) . 39
Page: 40

Repair Parts Parts List for Craftsman 10 " Bench Top Table Saw Model No . 113.221770 Figure 3 38 14 37 15 / 16 / 17 19 28 27 I 25 I 29 30 35 31 34 / 33 j32 4O
Page: 41

Repair Parts Parts List for Craftsman 10 " Bench Top Table Saw Model No . 113.221770 Always Order by Part Number - Not Key Number Figure 3 Key Part No . Key Part No . Description Description No No . 1 821151 - 3 23 823007 Screw , Hex Hd . M5 x . 8 - 20 Indicator , Blade Tilt 24 823005 2 STD852005 * Lockwasher , Ext . M5 Bracket , Indicator Support 823030 3 823O35 25 Bracket , Pivot Rod Spacer , 9.5 x 68.5 4 823105 Screw , Serr Hd . 1 / 4 - 20 x 3 / 4 26 STD54 ! 031 * Nut Hex 5 / 16 - 18 STD833016 5 813249 - 104 27 Screw , Hex Hd . M6 x 1 - 18 Pin , Roll 4 x 16 28 STD852006 6 823037 * Lockwasher , M6 Spacer 823018 7 823000 29 Nut , He × Special 3 / 8 - 16 x 5 / 32 Clamp , Rod Pivot Rear 30 823018 - 1 8 823034 Nut , Hex Special 3 / 8 - 16 x 13 / 64 Rod , Pivot 31 823019 9 822499 Washer , Fiber 10ram Clamp , Rod Pivot 808447 - 7 10 822488 32 Washer , Wave lOmm Nut , Hex 1 / 4 - 20 33 823017 11 STD541010 Bar , Rocker * Nut , Hex 10 - 24 34 823016 12 STD551210 Spacer 6.2 x 16 x3 . 1 * Lockwasher , Ext . # 10 35 820632 - 1 13 822489 - 1 Ring , Retaining Bolt , Carriage 1 / 4 - 20 x 1 - 1 / 4 36 823028 Bracket , Motor 14 802392 - 49 Spacer 823026 37 Motor ( see Fig . 5 ) 15 STD541025 * Nut , Hex 1 / 4 - 20 38 9 - 32556 t Blade , 10 " Chisel Tooth 16 STD551025 * Washer , 17 / 64 x 5 / 8 x 1 / 32 60547 Collar Blade 39 17 STD522532 * Screw , Hex Hd . 1 / 4 - 20 x 3 - 1 / 4 40 820818 Nut , Saw Arbor 18 823031 Plate , Deflector 821733 - 290 41 Pin , Roll 8 x 90 19 STD511003 * Screw , Pan Hd . t0 - 24 x3 / 8 42 823036 Plate , Mounting 20 823015 Spring , Compression 43 823029 Screw , Cr . Pan Hd Shoulder 21 STD551131 * Lockwasher , Ext . 5 / 16 Screw Pan Hd . Shoulder 44 823997 22 805517 Screw , Pan Hd . 5 / 16 - 18 x 1 / 2 Figure 4 Key Description Part No . _ 2 No . , L . Knob Miter Gauge 1 823065 60545 Washer , Nylon 2 823068 Pad , Sliding 3 Screw , Flat Cr . Hd . Ty " T - F " 4 823069 M4x 7x8 * Screw # 8 - 32 x 1 / 4 STD510802 5 Indicator , Miter Gauge 823066 6 Bar , Miter Gauge 7 823198 Body , Miter Gauge 8 823157 * Standard Hardware Item - May be Purchased Locally 1 Stock Item - May be secured through the hardware department of most Sears Retail Stores 41
Page: 42

Repair Parts Parts List for Craftsman 10 " Bench Top Table Saw Model No . 113.221770 Always Order by Part Number - Not Key Number Figure 5 19 2f 22 18 23 \ / i 17 2 3 4 / 5 / / I 14 13 / 12 / 10 7 11 Key Description No . Part No . Description NO . STD522505 * Screw , Hex Hd . 1 / 4 - 20 x 1 / 2 13 823186 Rip Fence Cam STD551225 * Lockwasher , 1 / 4 Ext 14 821733 - 107 Pin Roll 3 x 22 823181 Rear Sliding Pad 15 STD541031 o Pad No . * Nut , Hex 5 / 16 - 18 823180 Compression Spring ! 6 823185 Rip Fence Handle 823179 i Rear Clamp 17 823191 Lever Pin 823178 Clamp Rod 18 823188 Cam Pin 823182 Fence 19 823193 Rear Clamp Screw 823187 Sliding Pad 823069 Screw FI . Hal . Ty " T1 _ ' M4 x 7 - 8 21 823183 Rip Fence Housing 10 STD510802 • Screw Cr . Pan # 8 - 32 x 1 / 4 22 STD510802 * Screw Cr . Pan # 8 - 32 x 1 / 4 ! 1 823190 Front Spdng Clamp 23 823184 Rip Fence Indicator Bracket Fence Cam 823189 Figure 6 - - - - 1 Key 2 Description \ No , - - 823026 Motor ( Complete ) 1 46 _ 7477 - 3 * Screw Pan Hd M4 x 0.7 - 12 2 821143 Cap End 3 821141 Pad - Brush 4 821139 Housing Brush 5 821140 Brush 6 169123 - 15 Relief - Strain I Standard Item - May be Purchased - Locally J'J 4 WARNING : Any attempt to repair or replace electrical parts on this unit may create a hazard unless repair I 7 % is done by a qualified service technician . Repair ser - I 5 I vice is available through your nearest Sears Store . I 42
Page: 43

Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . parts List for Craftsman 10 " Bench Top Table Saw Model No . 113.221770 Always Order by Part Number - Not Key Number Figure 7 Key I Part No . Description Key Part No . Description No . 1 No . I 7 1825776 ! Rail bottom Front 1 825778 Rail Top Side 8 1825784 I Foot 2 825777 Rail Top Front Hardware For Mounting Tool 3 825774 Leg * Screw Hex Hd 5 / 16 - 18 x 2 - 1 / 2 4 STD533107 * Bolt Carriage 5 / 16 - 18 x 5 / 8 10 2ISTD5410315 9 f STD5231 t _ Nut Rex 5 / 16 - 18 5 825775 Rail Bottom Side STD541031 * Nut Hex 5 / 16 - 18 11 ISTD551031 t Washer 5 / 16 - 18 x 1 / 16 • Standard Item - May be Purchased Locally 43
Page: 44

i f f 10 iNCH BENCH TOP TABLE SAW MODEL NO . For the repair or replacement parts you need Call 7 am - 7 pro , 7 days a week 113.221770 1 - 800 - 366 - PART ( 1 - 800 - 366 - 7278 ) For i . - bome major brand repair service Call 24 hoursaday , 7 days a week 1 - 800 - 4 - REPAIR ( 1 - 800 - 473 - 7247 ) The model number of your table Forthe location of a saw is found at the rear of the SearsRepair Service Center in yo . r area base . Gall 24 hours a day , 7 days a week When requesling service or t - 800 - 488 - 11222 ordering parts , always provide the following information : For i . formatio , on purchasinga Sears • Product Type Maintenance Agreementor to inquire - Model Number about an existingAgreement * Part Number Call 9 am - 5 pro , M0nday - Saturday • Part Description 1 - 8OO - 821 - 6655 SEARS Amedca's Repair Speck _ lists % _ _ . , , w , _ J Sears , Roebuck and Co . , Hoffman Estates , IL . 60179 U . S . A . Part No . SP6048 Form No . SP6048 Printed in Taiwan 2 / 97
Search in Table Saw on ebay
"