Home | Register Login | Wanted Manuals | MarketPlace | Members Area | Manuals Manufacturer Directory | UPC Lookup | Information Pages | Policy


Back To Craftsman Table Saw       Model: 113.241691 or 113241691 Craftsman 10 Inch Flex Drive Saw Table
Regular Text Search or Search by Model Number

Register / log-in to add to your Hammerwall Collection.
Manual Location


This is a partial text extraction from the pdf, to download the pdf, click the Manual tab. If you want to search this text, hold control and F, and type the word you are looking for.

Page: 1

Save This Manual For Future Reference owners manual MODEL NO . 113.241591 SAW WITH LEGS TWO CAST IRON TABLE EXTENSIONS MOTOR AND HOLD DOWN CLAMP L Serial Number Model and serial number may be found # at the rear of the base . You should record both model and serial number in a safe place for DELUXE IO - INCH future use . FLEX DRIVE TABLE SAW CAUTION : . assembly READ ALL INSTRUCTIONS . operating CAREFULLY = repair parts Sold by SEARS , ROEBUCK AND CO . , Chicago , IL . 60684 U . S . A . PriP , _ : ed _ n U _ Part No . 62965
Page: 2

_ , . i i . . . . . . . . . . . . . . FULL ONE YEAR WARRANTY ON CRAFTSMAN TAB LE SAW If within one year from the date of purchase , this Craftsman Table Saw fails due to a defect in material or workmanship , Sears will repair it , flee of charge . WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SERVICE CENTER / DEPARTMENT THROUGHOUT THE UNITED STATES . This warranty applies only while this product is in use in the United States . This warranty gives you specific legal rights , and you may also have other rights which vary from state to state . SEARS , ROEBUCK AND CO . . Dept . 698 / 731A , Sears Tower , Chicago , IL 60684 GENERAL SAFETY iNSTRUCTIONS FOR POWER TOOLS 1 . KNOW YOUR POWER TOOL Z87 . 1 ) at all times . Everyday eyeglasses onlyT have impact resistant lenses , they are NO Read and understand the owner's manual and safety glasses . Also , use face or dust mask if iabels affixed to the tool Learn its application cutting operation is dusty , and ear protectors end imitations as well as the specific potential ( plugs or muffs ) during extended periods of hazards peculiar to this tool . operation . 2 . GROUND ALL TOOLS 13 . SECt . iRE WORK This tool is equipped with an approved 3 - Use clamps or a vise to hold work when conductor cord and a 3 - prong grounding type practical . It's safer than using your hand , frees plug to fit the proper g rounding type receptacle . both hands to operate tool . The green conductor in the cord is the grounding wire . Never con nect the green wi re to 14 . DON'T OVERREACH a live terminal . Keep proper footing and balance at all times . 3 , KEEP GUARDS IN PLACE 15 . MAINTAIN TOOLS WITH CARE in working order , and in proper adjustment and Keep tools sharp and clean for best and safest alignment . performance . Follow instructions for lubricating 4 . REMOVE ADJUSTmNG KEYS and changing accessories . AND WRENCHES 16 . DISCONNECT TOOLS Form habit of checking to see that keys ando _ before servicing ; when changing accessories adjusting wrenches are removed from to such as blades , bits , cutters , etc . before turning it on . 17 . AVOID ACCIDENTAL STARTING 5 . KEEP WORK AREA CLEAN Make sure switch is in " OFF " position before Cluttered areas and benches invite accidents , plugging in Floor must not be slippery due to wax or sawdust . 18 . USE RECOMMENDED ACCESSORIES Consult the owner's manual for recommended 6 . AVOID DANGEROUS ENVIRONMENT Don't use power tools in damp or wet locations accessories . Follow the instructions that or expose them to rain . Keep work area well accompany the accessories . The use of lighted . Provide adequate surrounding work improper accessories may cause hazards . space . 19 . NEVER STAND ON TOOL 7 . KEEP CHILDREN AWAY Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted . All visitors should be kept a safe distance from Do not store materials above or near the tool work area , such that it is necessary to stand on the tool to 8 . MAKE WORKSHOP CHILD - PROOF reach them . - - with padlocks , master switches , or by removing Starter keys . ) r other S , DON'T FORCE TOOL carefully Iwt will do the job better and safer at the rate for hich it was designed , and for all of moving and any . A guard 11 . WEAR PROPER PPAREL Do not wear Ioo clothing ; gioves , neckties or jewelry ( rings , _ St watches ) to get caught in nnovihg part N0nslip footwear is recommended . Wear protective hair covering tohe contain long hair . Roll long sleeves above t elbow . 12 . USE SAFETY GOGGLES ( Head Protection ) Wear Safety goggles ( must comply with ANS ! a 2
Page: 3

ADDITIONAL SAFETY iNSTRUCTiONS FOR TABLE SAWS WARNING : FOR YOUR OWN SAFETY , DO NOT operating immediately until the particular OPERATE YOUR SAW UNTIL IT IS COMPLETELY part is properly repaired or replaced . ASSEMBLED AND INSTALLED ACCORDING TO B . Small loose pieces of wood or other objects that contact the rear of the revolving bladeat THE INSTRUCTIONS . . . AND UNTIL YOU HAVE can be thrown back at the operator READ AND UNDERSTAND THE FOLLOWING . excessive speed . This can usually be avoided 1 . GENERAL SAFETY INSTRUCTIONS FOR by keeping the guard and spreader in placeg POWER TOOLS . . . SEE PAGE 2 for all thru - sawing operations ( sawin 2 . GETTING TO KNOW YOUR SAW . . . SEE PAGE entirely thru the work ) AND by removing all 27 . loose pieces from the table with a long stickff . of wood IMMEDIATELY after they are cut obly 3 . BASIC SAW OPERATION . . . SEE PAGE 30 . Use extra caution when the guard assem 4 , MAINTENANCE . . . SEE PAGE 38 . C . is removed for resawing , dadoing , rabbeting , 5 . STABILITY OF SAW or molding replace the guard as soon as that operation is completed . if there is any tendency for the saw to tip over or For rip or rip - type cuts , the following end of a move during certain cutting operations such as D . workpiece to which a push stick or pushe cutting extremely large heavy panels or long board is applied must be squar heavy boards , the saw should bebolted down . ( perpendicular to the fence ) in order thatye If you attach any kind of table extensions overuas feed pressure applied to the workpiece tbh 24 " wide to either end of the saw , make sure yo the push stick or block does not cause either bolt the saw to the bench or floor workpiece to come away from the fence , and appropriate , or support the outer end of theas possibly cause a kickback . extension from the bench or floor , During rip and rip type cuts . the workpiecenst appropriate . E . must be held down on the table and agai 6 . LOCATION the fence with a push stick , push block , oorf The saw should be positioned so neither the featherboards . A featherboard is made operator nor a causal observer is forced to stand solid lumber per sketch . in line with the saw blade . ] _ 24 ' " I 7 . KICKBACKS A " KICKBACK " occurs during a rip - type operation when a part or all of the workpiece _ s 5 / 16 " AP _ T thrown back violently toward the operator . Keep your face and body to one side of the - 5 " ' - - . - . 1 sawblade , out of line with a possible " Kickback . " Kickbacks and possible injury from them F . NEVER turn the saw " ON " before clearing can usually be avoided by : the table of all tools , wood scraps , etc . A . Maintaining the rip fence parallel to the except the workpiece and related feed of sawblade . support devices for the operation planned . B . Keeping the sawblade sharp . Replace ors G . NEVER place your face or body in line witf " sharpen anti kickback pawls when point the cutting tool . become dull . H . NEVER place your fingers or hands in the C . Keeping sawblade guard , spreader , andg path of the sawblade or other cutting tool . antikickback pawls in place and operatin I . NEVER reach in back of the cutting tool witl " properly . The spreacler must be in alignment either hand to hold down or support th _ with the sawblade and the pawls must stop a workpiece , remove wood scraps , or for an _ kickback once it has started , other reason . Avoid awkward operations anc Check their action before ripping . hand positions where a suddenmovS _ lcPoiunltco " D . NOT ripping work that is twisted or warpedde cause fingers or hand totool . or does not have a straight edge to gui sawbtade or other cutting along the rip fence . J . DO NOT perform layout , assembly , or setu _ E . NOT releasing work until you have pushed it work on the table while the cutting toot i , ' all the way past the sawblade . rotating . F . Using a push stick for ripping widths of 2 to 6or K . DO NOT perform any operatior in , and an auxi iary fence and push block f " FREEHAND " - - always use either the ri [ ; ripping widths narrower than 2 in . ( See fence or the miter gauge to position ant " Basic Saw Operation Using The Rip Fence " guide the work . section . ) L . NEVER use the rip fence when crosscuttin _ G , NOT c6nfining the cut - off piece when . . . . . miter gauge when ripping . DO NO ! use the rip fence as a length stop . Never hold onto or touch the " freeend " of the section of the workpiece between the saw workpiece or a " free piece " that is cut off blade and the rip fence while power is " ON " and / or the sawbiade i , . rotating . 8 . PROTECTION : EYES , HANDS , FACE , EARS , M . Shut " OFF " the saw and disconnect th _ BODY power cord when removing the table insertot A . If any part of your saw is malfunctioning , hase changing the cutting tool , removing been damaged or broken . . , such as th replacing the blade guard , or makin { ; motor switch , or other operating control , sae adjustments . safety device or the power Cord . . . cea
Page: 4

when ripping , use the maximum diameter bladese N . Provideadequatesupportto the rearandng f0 r which the saw is designed , since under the sides of the saw table for wider or lo conditions the spreader ts nearest the blade workpieces . O . Plastic and composition ( like hardboard ) 14 . Adjust table inserts flush with the table top . materials may be cut on your saw . However , NEVER operate the saw unless the proper insert since these are usually quite hard and is installed . slippery , the antikickback pawls may not 15 . NEVER feed material into the cutting tool from stop a kickback . the rear of the saw . An accident and serious Therefore , be especially attentive to injury could result . following proper set - up and cutting 17 . NEVER use another person as a substitute for aa procedures for ripping Do not stand , or table extension , or as additional support for permit anyone else to stand , in line with a workpiece that is longer or wider than the basicor potential kickbackjam saw table , orto assist in feeding or supporting P . If you stall or the sawblade in the workpiece , turn saw " OFF " , remove the pulling the work piece . workpiece from the sawblade and check to DO NOT pu the workpiece through the see if the sawblade is parallel to the miter sawblade - position your body at the nose ( in - feed ) side of the guard : start and complete the gauge grooves and if the spreader is inIf cut from the same side . This will require added proper alignment with the sawblade . table support for long or wide workpeices thatw ripping at the time , check to see if the ripst extend beyond the length or width of the sa fence is parallel with the sawblade . Readju table . as indicated . Q . DO NOT remove small pieces of cut - off 18 . THINK SAFETY . material that may become trapped inside the Safety is a combination of operator common blade guard while the saw is running . This sense and alertness at all times when the saw is could endanger your hands or cause tail being used . kickback . Turn saw " OFF " and wait un 19 . NOTE AND FOLLOW SAFETY INSTRUC - blade stops . TIONS THAT APPEAR ON THE FRONT OF R . Use extra care when ripping wood that has a YOUR SAW . twisted grain or is twisted or bowed it maye . rock on the table and / or pinch the sawblad 9 . KNOW YOUR CUTTING TOOLS READ AND UNDERSTAND OWNERS MANUAl . BEFORE OPERATING MACHINE . A . Dull , gummy , or improperly sharpened or set I wrc _ RSAFETYGOGGLES . S , KNOWHOWTO _ VOtD " KICKIBACKS . " USE $ AWI _ DE GUARO FOR " [ HRU - SAWIN G . " 6 , DO NOT PERFORM OPERATIONS " PREEHANO , " cutting tools can cause material to stick , jam , KEE _ i4ANDS OUT OF PATH OF SAW . LADE . 7 . NEVER REACH AROUND OR OVER $ AWBLADE , I DANGER I FOR YOUR OWN SAFETY : stall the saw , or kickback at the operator . USE A " PUSH . ST _ CK " WHEN REQUfRIEID * WARNING : uSElze VOLT t5 , _ P SP . NCR CIRCUITA _ O USE ISAMP TIME BELAYFUSE Minimize potential injury by proper cutting tool and machine maintenance . 20 . WARNING : DO NOT ALLOW FAMILIARITY NEVER ATTEMPT TO FREE A STALLEDG ( GAINED FROM FREQUENT USE OF YOUR SAWBLADE WITHOUT FIRST TURNIN SAW ) TO BECOME COMMONPLACE . - THE SAW OFF . ALWAYS REMEMBER THAT A CARELESS B . Never use grinding wheels , abrasive cut - offg FRACTION OF A SECOND IS SUFFICIENT TO wheels , friction wheels ( metal slittin INFLICT SEVERE INJURY . blades ) wire wheels or buffing wheels . NOTE : Do not overtighten arbor nut . Use the arbor 10 . USE ONLY ACCESSORIES DESIGNED FOR . wrench to just " snug " it . THIS SAW . 11 . Crosscutting operations are more aconvenientlyry worked and with greater safety if an auxili WEAR YOUR wood facing is attached to the miter gauge usingste the holes provided . However , the facing muth not interfere with the proper functioning of sawblade guard . 12 . Make sure the top of the arbor or cutting tool rotates toward you when standing in normal operating position . Also make sure the cutting t0ol , arbor collars and arbor nut are installed properly . Keep the cutting tool as low as _ ) osstble for the operation being performed The operation of any power tool can result in foreign
Page: 5

MOTOR SPECIFiCATiONS AND ELECTRICAL REQUIREMENTS This saw is equipped with a 3 - conductor cord and This saw is designed to use a 3450 RPM motor only . Do not use any motor that runs faster than 3450 grounding type plug which has a grounding prong , approved by Underwriters ' Laboratories and the RPM . It is wired for operation on 110 - 120 volts , 60E Hz . , Alternating current . IT MUST NOT B Canadian Standards Association . The groundol CONVERTED TO OPERATE ON 230 VOLTS . conductor has a green lug and is attached to theto housing at one end and to the ground prong in the The Black and Red motor leads are connected to attachment plug at the other end . quick connect tabs " A " and " B " on terminal board . This plug requires a mating 3 - conductor grounded WARNING : Do not change any of these connec - type outlet as shown . tions with current on . If the outlet you are planning to use for this saw is of BLACK the two prong type DO NOT REMOVE OR UALTERse THE GROUNDING PRONG iN ANY MANNER . TS an adapter as shown and always connect the POWER LEAD grounding lug to a known ground . REW it is recommended that you have a qualified electrician replace the TWO prong outlet with a properly grounded THREE prong outlet . A temporary adapter as shown below is available forn connecting plugs to 2 - prong receptacles . The gree PowE . LEAD ' - - ' grounding lug extending from the adapter must be connected to a permanent ground such as to a CAUTION : Oo not use blower or washing machine properly grounded outlet box . motors or any motor wifh an automatic reset . A temporary adapter as illustrated is available fore overload protector as their use may be hazardous connecting plugs to 2 - prong receptacles . Th For replacement motor refer to parts list in this temporary adapter should be used only until a manual . properly grounded outlet can be installed by a qualified electrician . CONNECTING TO POWER SOURCE OUTLET GROUNDING LUG This saw must be grounded while in use to protect the operator from electrical shock . If power cord is worn or cut , or damaged in any way , have it replaced immediately . If your saw is for use on less than 150 volts it has a plug that looks like below . ADAPTER 3 - PRONG PLUG WARNING : THE GREEN GROUNDING LUG EXTENDING FROM THE ADAPTER MUST BE / , DI CONNECTED TO A PERMANENT GROUNE SUCH AS TO A PROPERLY GROUNDED OUTLE1 0 BOX . NOT ALL OUTLET BOXES ARE PROPERL _ \ / n gt GROUNDED . GROUNDING PRONG I t _ I . PROPERLY GROUNDED If you are not sure that your outlet box is properl _ 3 * PRONG OUTLET grounded , have it checked by a qualified electrician NOTE : The adapter illustrated is for use only if yoL Plug power cord of fully assembled saw into 110 - already have a properly grounded 2 - pron _ 120V properly grounded type outlet protected by a receptacle . 15 - am p . time delay or Circuit - Saver fuse or circuit The use of any extension cord will cause some los , ' breaker . of power . To keep this to a minimum and to prevenb ! IF YOUR ARE NOT SURE THAT YOUR OUTLET IS over - heating and motor burn - out , use the ta _ . PROPERLY GROUNDED , HAVE IT CHECKED BY below to determine the minimum wire size ( A . W . G A QUALIFIED ELECTRICIAN . extension cord , Use only 3 wire extension cord , , WARNING : DO NOT PERMIT FINGERS TO which have 3 prong grounding type plugs and 3 . TOUCH THE TERMINALS OF PLUG WHEN pole receptacles which will accept the plug on th _ INSTALLING OR REMOVING THE PLUG TO OR SBW . FROM THE OUTLET . The motor must rotate COUNTERCLOCKWISI WARNING : IF NOT PROPERLY GROUNDED THIS when viewed from the shaft end . POWER TOOL CAN INCUR THE POTENTIAL HAZARD OF ELECTRICAL SHOCK PARTICU - 1 H , P . MOTOR 110 - 120V LARLY WHEN USED IN DAMP LOCATIONS , IN . Extension Cord Length Wire SIze A . W . G . PROXIMITY TO PLUMBING , OR OUT OFDOORS Up to 50 Ft . . . . . . . . . . . . . . . . . 14 50 to 100 Ft . . . . . . . . . . . . . . . . 12 SUCH AS YOUR HANDS CONTACTING THE 100 - 200 Ft . . . . . . . . . . . . . . . . 10 SAWBLADE . 200 - 400 Ft . . . . . . . . . . . . . . . . . 8
Page: 6

CONTENTS WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Elevation Handwheet . . . . . . . . . . . . . . . . . . . . . . 28 GENERAL SAFETY INSTRUCTION Tilt Handwheel . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 FOR POWER TOOLS . . . . . . . . . . . . . . . . . . . . . . 2 Tilt Lock Handle . . . . . . . . . . . . . . . . . . . . . . . . . . 28 ADDITIONAL SAFETY INSTRUCTIONS Rip Fence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 FOR TABLE SAWS . . . . . . . . . . . . . . . . . . . . . . . . 3 Miter Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2288 MOTOR SPECIFICATIONS AN D ELECTRICAL Blade Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . 5 " Fable Insert . . . . . . " . . . . . . . . . . . . . . . . . . . . . . . . 28 UNPACKING ANC CHECKING CONTENTS . . 6 Removing and Installing Sawblade . . . . . . . . . 299 Tools Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Exacti - Cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 List of Loose Parts . . . . . . . . . . . . . . . . . . . . . . . . . 79 BASIC SAW OPERATION USING THE MITER ASSEMB L . Y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GAUGE Assembling Steel Legs . . . . . . . . . . . . . . . . . . . . . 9 Work Helpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Mounting Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 910 Crosscutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Installing Handwheels . . . . . . . . . . . . . . . . . . . . . Repetitive Cutting . . . . . . . . . . . . . . . . . . . . . . . . . 31 Checking Table Insert . . . . . . . . . . . . . . . . . . . . . 10 Miter Cutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3322 Heeling Adjustment of Parallelism of Bevel Crosscutting . . . . . . . . . . . . . . . . . . . . . . . . Sawblade to Miter Gauge Groove . . . . . . . . . 1112 Compound Miter Cutting . . . . . . . . . . . . . . . . . . 33 Blade Tilt , or Squareness of Blade to Table BASIC SAW OPERATION USING THE RIP Tilt Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 FENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Mounting The Motor . . . . . . . . . . . . . . . . . . . . . . 14 Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Mounting The Flexible Shaft . . . . . . . . . . . . . . . 1518 Bevel Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Attaching Table Extensions . . . . . . . . . . . . . . . Ploughing and Molding . . . . . . . . . . . . . . . . . . . 3356 Aligning Extensions . . . . . . . . . . . . . . . . . . . . . . . 19 Resawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting Switch . . . . . . . . . . . . . . . . . . . . . . . . . . 1919 Cutting Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3366 Installing Rip Fence Guide Bars . . . . . . . . . . . Rabbeting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Aligning Rip Fence . . . . . . . . . . . . . . . . . . . . 21 Dadoing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Adjusting Rip Scale Indicator . . . . . . . . . . . . . . 23 Using Featherboards . . . . . . . . . . . . . . . . . . . . . . 37 Installing Blade Guard . . . . . . . . . . . . . . . . . . . . 23 MOTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3388 Aligning Spreader . . . . . . . . . . . . . . . . . . . . . . . . 25 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adjusting Miter Gauge . . . . . . . . . . . . . . . . . . . . 2526 LUBRICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Assembling Hold - Down . . . . . . . . . . . . . . . . . . . RECOMMENDED ACCESSORIES . . . . . . . . . . . 4390 Plugging in the Motor . . . . . . . . . . . . . . . . . . . . . 26 TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . . . . . GETTING TO KNOW YOUR SAW . . . . . . . . . . . 2727 REPAIR PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 On - Off Switch . . . . . . . . . . . . . . . . . . . . . . . . . UNPACKING AND CHECKING CONTENTS COMBINATION SQUARE MUST BE TRUE . TOOLS NEEDED ; _ " _ - J _ - _ _ STRAIGHT EDGE OF BOARD 3 / 4 " THICK . THIS EDGE MUST Hammer MedlumSsmcreawll drlverSCrewdrlver DRAW LIGHT LINE ON " _ BE PERFECTLY STRAIGHT . BOARD ALONG THIS EDGE , _ , \ _ - \ i l - # 2 Phillips Screv _ ldver I f Mlere i _ j j SHOULD BE NO GAP OR OVERLAP CombP " Uon Sq - are Wrenches HERE WHEN SQUARE IS FLIPPED OVER IN DOTTED POSITION . i ' 7rt . . . . . . . . . . • . . . . . . . . . . . . . . . . . . . . . . . . . plied to the table any ordinary spot remover . health hazard never use riaiii Separate al parts from packing mat highly volatile solvents . re each one with the illustration and t wax to the table . Parts to make certain all items are accal ri , cloth . before discarding any packing rnai NEVER 3E OUTLET = . TE ,
Page: 7

LIST OF LOOSE PARTS item Part Name Qty , Item Part Name Qty . Loose Parts Bag No . 62752 for Legs . . . 1 A Blade Guard and Spreader . . . . . . . . . . . 1 ( Containing the Following Items ) : B Rip Fence . . . . . . . . . . . . . . . . . . . . . . . . . . 1 A Screw , Truss Hd . Ji4 - 20 x 5 / 8 . . . . 24 C Owners Manual . . . . . . . . . . . . . . . . . . . . . 1 B Lockwasher , External 1 / 4 . . . . . . . . 24 D Miter Gauge . . . . . . . . . . . . . . . . . . . . . . . . 1 B Lockwasher , External 5 / 16 . . . . . . . 4 E Rod , Separation ( Fence ) . . . . . . . . . . . . . 1 C Nut , Hex 1 / 2 - 13 . . . . . . . . . . . . . . . . . 8 F Leg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 C Nut , Hex 1 / 4 - 20 . . . . . . . . . . . . . . . . . 24 G Stiffener , End . . . . . . . . . . . . . . . . . . . . . . . 2 H Stiffener , Side 2 C Nut , Hex 5 / 16 - 18 . . . . . . . . . . . . . . . . 4 J Handwheel . . . . . . . . . . . . . . . . . . . . . . . . . 2 D Screw , Hex 5 / 16 - 18 x 1 - 1 / 4 . . . . . . 4 E Washer , 11 / 32 x 11 / 16 x 1 / 16 . . . . 8 K Extension , 12 x 27 . . . . . . . . . . . . . . . . . . . 2 L Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 F Foot , Leveling . . . . . . . . . . . . . . . . . . 4 M Motor Mount . . . . . . . . . . . . . . . . . . . . . . . 1 Loose Parts Bag No . 62890 . . . . . . . . . . . 1 N Shaft , Flexible . . . . . . . . . . . . . . . . . . . . . . 1 ( Containing the Following Items ) : 0 Rip Fence Guide Bar with Rip Scale . . . 1 B Lockwasher , External # 10 . . . . . . . . 3 P Rip Fence Guide Bar , Rear . . . . . . . . . . . . 1 B Lockwasher , External 114 . . . . . . . . 6 Loose Parts Bag . . . . . . . . . . . . . . . . . . . . t B Lockwasher , External 5116 . . . . . . . 4 ( Containing the following items ) : C Nut , Hex 1 / 4 - 20 . . . . . . . . . . . . . . . . . 6 Loose Parts Bag No . 62752 . . . . . . . 1 C Nut , Hex 5 / 16 - 18 . . . . . . . . . . . . . . . . 8 Loose Parts Bag No . 62890 . . . . . . . 1 D Screw , Hex Hd . 1 / 4 - 20 x 1 . . . . . . . 2 Loose Parts Bag No . 62951 . . . . 1 E Washer , 21 / 64 x 5 / 8 x 1 / 16 . . . . . . 2 Loose Parts Bag No . 62891 . . . . . . . 1 E Washer , 17 / 64 x 3 / 4 x 1 / 16 . . . . . . 2 O Outlet , On / Off . . . . . . . . . . . . . . . . 1 E Washer , 21 / 64 x 47 / 64 x 1 / 16 . . . . 4 R Key , Switch . . . . . . . . . . . . . . . . . t G Screw , Pan Hd . Type T 10 - 32 x 3 / 8 3 S Wrench , Arbor . . . . . . . . . . . . . . . 1 H Bolt , Carriage 1 / 4 - 20 x 3 / 4 . . . . . . . 4 T Bracket , Shaft . . . . . . . . . . . . . . . 2 H Bolt , Carriage 5 / 16 - 18 x 3 / 4 . . . . . . 4 U Support , Spreader . . . . . . . . . . . 1 J Nut , Hex Jam 5 / 16 x 18 . . . . . . . . . . 2 ¢ G T G U 7
Page: 8

Item Part Name Qty . Item PartName Qty . Loose Parts Bag No . 62951 . . . . . . . . . . . 1 Loose Parts Bag No . 62891 . . . . . . . . . . . 1 ( Containing the Following Items ) : ( Containing the Following Items ) : A Nut , Weld . . . . . . . . . . . . . . . . . . . . . . 1 A Bolt . Carriage 1 / 4 - 20 x 3 / 4 . . . . . . . 4 B Clamp Spreader . . . . . . . . . . . . . . . . 1 B Screw , Soc . Set 1 / 4 - 20 x 1 . . . . . . . 2 C Bracket , _ ; preader . . . . . . . . . . . . . . 1 C Washer . 17 / 64 x 9 / 16 x 3 / 64 . . . . . 4 D Lockwasher , External 1 / 4 . . . . . . . . 6 D Nut , Hex 1t4 - 20 . . . . . . . . . . . . . . . . . 4 D Lockwasher , External # 10 . . . . . . . . 2 E Nut , Wing 1 / 4 - 20 . . . . . . . . . . . . . . . . 2 D Lockwasher , External 5 / 16 . . . . . . . 14 F Screw , Hex Hd . 5116 - 18 x 1 - 3 / 4 . . . 2 E Wrench , Hex " L " 3 / 32 . . . . . . . . . . . 1 F Screw , Hex Hd . 5 / 16 - 18 x 3 / 4 . . . . 2 E Wrench , Hex " L " 1 / 8 . . . . . . . . . . . . 1 F Screw , Hex Hd . 5 / 16 - 18 x 1 . . . . . . 2 E Wrench , Hex " L " 5 / 32 . . . . . . . . . . . 1 G Screw , Pan Hd . 10 - 32 x 3 / 4 . . . . . . . 2 F Tie Wire . . . . . . . . . . . . . . . . . . . . . . 2 H Key , Sq . 3 / 16 . . . . . . . . . . . . . . . . . . . 1 G Spacer , Fence Guide Bar . . . . . . . . . 2 H Nut , Self - Threading . . . . . . . . . . 28 J Screw , Hex Hd . 5 / 16 - 18 x 1 - 1 / 4 . . . K Nut , Hex Jam 5 / 16 - 18 . . . . . . . . . . . 8 L Connector . Motor . . . . . . . . . . . . . . . 1 M Washer 11 / 32 x11 / 16 x1 / 16 . . . . 8 C D E A A B C D E H G F G H F M K The Hold Down is included with Model 113,241691 Item Part Name Qty . A ClampAssembly . . . . . . . . . . . . . . . . . . . . 122 B Wing Screw . . . . . . . . . . . . . . . . . . . . . . . . . C Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D Support Rod . . . . . . . . . . . . . . . . . . . . . . . . 1 8
Page: 9

ASSEMBLY o ASSEMBLING STEEL LEGS ASSEMBLE SCREWS NOTE : Steel Legs are furnished with Model J " THROUGH HOLES - / f MARKED " X " 113.241691 , From among the loose parts , find the 7 following Hardware : " _ , SIDE STIFFENER 24 Truss Head Screws , 1 / 4 - 20 x 5 / 8 in . long ( top of screw is rounded ) 24 Lockwashers . 1 / 4 in . External Type ( approx . dia . of hole 1 / 4 in . ) 24 Hex Nuts , 1 / 4 - 20 ( approx , dia . of hole 1 / 4 in . ) 8 Hex Nuts , 1 / 2 - 13 ( approx . dia . of hole 1 / 2 in . ) END 4 Leveling feet . STIFFENER " Assemble the legs as shown . . . 1 . Insert the Truss Head Screws through the holes in the legs , then through the holes in theO stiffeners . MAKE SURE THE SCREWS G THROUGH THE HOLES IN THE SIDE STIFFENERS MARKED " X " . _ 21N . HEX NUTS 2 . Install the Iockwashers , . . screw on the nuts but Do Not tighten until completely assembled . 3 , Install leveling feet . MOUNTING SAW 1 . From among the loose parts , find the following hardware : 4 Hex Head Screws , 5 / 16 - 18 x 1 - 1 / 4 in . long . 4 Hex Nuts , 5 / 16 - 18 ( approx . dia . of hole 5 / 16 in . ) 4 Lockwashers , 5 / 16 in . External Type ( approx , dia . of hole , 5 / 16 in . ) 8 Flat Washers , ( dia . of hole 11 / 32 in . ) 2 . Place saw on legs so that holes in bottom of saw line up with holes in top of legs . / / / SAW BASE HEX HEAD SCREW _ , _ l I FLAT WASHER 3 , install screws , washers , Iockwashers and nuts as END ; shown . STIFFENER - ' I ' I
Page: 10

11,1 / 4 1 OPENING If you mount the saw on any other bench , make sure 16 " 3 / 4 " that there is an opening in the top of the bench the same size as the opening = nthe bottom of the saw dso that the sawdust can drop through . Recommende 15,1 working height is 33to 37 inches from the top of the saw table to the floor . @ 7116 " DIA , HOLES - - _ - - _ FRONT Ot : SAW IMPORTANT - - Read Before Proceeding Blade cannot be more than 2 inches above the table top when tilting the sawblade to make bevel cuts oro adjustments , Lower blade to 2 inches or closer t the table top to tilt the saw , Failure to do this may . OCKWASHER result in damage to your saw . / / INSTALLING HANDWHEELS 10 - 32 x 3 / 4 IN . Line up FLAT SPOTS on shaft and handwheel , push CPHILLIPSREW handwheel onto shaft . Install screw and Iockwashe r HEAD S ELEVATION to lOck handwheels on shaft . HANOWB TILT HANDWHEEL / / CHECKING TABLE INS ERT 1 . Insert should be even with table top . Check as shown . Loosen flat head screw that holds insert and adjust the four set screws as necessary , Tighten flat head screw . Do not _ ighten screw to the point where it deflects the insert . 3 / 32 IN SETSCREW WRENCH 2 . To remove insert . A . Loosen Phillips Flat Head Screw . B : Lift insert from front end , and pull toward front of saw . 3 . To replace insert : Place insert into insert opening in table and pushtil toward rear of sawto engage spring clip and un keyslot in insert w ! drop over screw T ghten screw . Do not tighten screw to the point where it will deflect the insert . /
Page: 11

HEELING ADJUSTMENT or PARALLELISM MARK'X " ON TOOTH OF SAWBLADE TO MITER GAUGE GROOVE While cutting , the material must move in a straight line PARALLEL to the SAWBLADE . . . therefore both the miter gauge GROOVE and the RIP FENCE must be PARALL : EL to the SAWBLADE , If the sawblade IS NOT parallel to the miter gauge groove , the blade will bind at one end of the cut . ( This is known as " HEELING " ) . To check for parallelism : WARNING - - TO AVOID INJURY FROM ACCIDENTAL START , TURN SWITCH " OFF " ANDT , REMOVE PLUG FROM POWER SOURCE OUTLE 1 . Raise blade all the way up by turning elevation handwheel clockwise , 4 . Move square to REAR , rotate blade to see if 2 . Mark an " x " on one of the teeth which is SET MARKED tooth again touches blade of square . ( bent ) to the LEFT . 5 . If tooth touches square at FRONT and REAR . 3 . Place the head of a combination square in the sawblade is PARALLEL to MITER GAUGE GROOVE . . . adjust blade of square so that it just GROOVE . touches the tip of the MARKED tooth . 6 . If tooth does not touch the same amount . . , the o mechanism underneath must be adjusted to make the blade PARALLEL to GROOVE . A . Rear support bearing must be moveds TOWARD the combination square if there i a space between marked tooth and end of square in step 4 . B . Rear support bearing must be moved AWAY / REAR SUPPORT o from the square if marked tooth pushes square BEARING out of position i _ the groove . I c , A's . , c . E - 7 . Make sure tilt clamp screw is tightened . " - L _ F 8 . Loosen both screws that hold the rear support ' " _ L _ - _ = J - ' _ _ - bearing and both screws that hold the front support bearing , NOTE ; Rear screws can be reached through back of saw . Use a 9 / 16 - in . wrench . To reach front support bearing screws insert open end wrench through opening in front of base by the tilt clamp screw . BEARING il
Page: 12

WOOD BLOCK • 9 . Using a wood block and hammer as shown , move / rear support bearing to right or left as req ui red to realign the blade . If necessary , shift front support bearing in similar manner ; butdo NOT move front support bearing unless necessary , Recheck the alignment with the square , then securely retighten all support bearing screws . NOTE : Be certain that the widest blade you use does not contact blade insert after moving support bearing . Check this at both 0 ° ( perpendicular to the table ) and 45 ° bevel by rotating the fully elevated blade by hand . Readjust as required to maintain sufficient clearance . BLADE TILT , OR SQUARENESS OF BLADE TO TABLE 90 ° ( SQUARE ) and 45 ° ( BEVEL ) STOP SCREWS . When the bevel pointer is pointing directly to thed " O " mark on the bevel scale , the sawblade shoul make a SQUARE cut 90 ° to the table . To check for SQUARENESS : . WARNING : TO AVOID INJURY FRONt ACCIDENTAL START , TURN SWITCH " 0 FF " ANDT , REMOVE PLUG FROM POWER SOURCE OUTLE 1 . Blade should be all'the way UP . 2 . Place the square against blade . Make sure square is nottouching the TIP of one of the saw TEETH O " _ J / _ _ - - TILT CLAMP SCREW - , , _ " _ " _ TILT LOCK I'IAN [ ) LE 3 . Turn the tilt - lock handle ( COUNTER - - CLOCKWISE ) to loosen the tilt clamp screw . 4 . NOTE : Handle is spring loaded for engagement with screw head - - must be pushed inward for disengagement whenever necessary to obtain a new grip on screw head . / / \ 12
Page: 13

/ / If blade is NOT SQUARE to table . . the 90 ° stop screw must be ADJUSTED . ! A . Unscrew 90 ° STOP SCREW three to four turns / using 3 / 16 in setscre . w wrench . B . Turn tilt handwheel clockwise oneturn , then turnis \ handwheel counterclockwise until blade \ square with table . i O C . Screw 90 ° stop screw IN until it stops . . , check \ once again for squareness and readjust screw , if 90 ° \ STOPSCREW necessary . 1 J If blade is SQUARE to table : A . Check pointer IF POINTER DOES NOT point to the " O " mark on 2 the bevel scale : A . Remove Elevation Handwheel . B . Loosen pointer screw and adjust pointer using / / medium screwdriver . / , / C . Reinstall Elevation Handwheel . POINTER AT " 0 " POSITION HEAD OF COMBINATION SQUARE NOTE : Lower sawblade elevation before tilting sawblade . Failu re to do this may result in damage to your saw . 1 . Lower the blade to about two inches above the table . 2 . Turn tilt handwheel counterclockwise to tilt blade to a 45 ° bevel . 3 . Raise blade elevation to maximum height . 4 . Check bevel of blade with the head of the combination square . - - - k If blade is NOT 45 ° to table . . , the 45 ° stop screw \ must be ADJUSTED . / A . Unscrew 45 ° STOP SCREW three to four turns / using 3 / 16 in . setscrew wrench . B . Turn tilt handwheel until blade is45 ° to the table . C . Screw 45 ° stop screw IN until it stops . . , check once again and readjust screw , if necessary . \ \ 5 Lower blade ; \ 6 . Tilt blade back to 90 ° . 7 . Tighten tilt lock handle . 8 . Lower blade below table . 13
Page: 14

TiLT MECHANISM Lower blade to 2 inches or closer to the table top TILT HANDWHEEL before tilting blade . Failure to do this may result in damage to your saw . The handwheel should turn freely without binding . The turn ing action can be adjusted by tightening or loosening the screws in the bearing retainer . _ J NOTE : Tilt Handwheel must be removed to adjust . ADJUST THESE When adjusting the screws in the bearing retainer TWO SCREWS using a screwdriver , hold the nut inside using a 3 / 8 in . wrench . MOUNTING THE MOTOR 1 . CHECK MOTOR ROTATION A . The motor must rotate COUNTER - - DIAMETER SHAFT CLOCKWISE when viewed from the shaft end . B . MAKE SURE " ' KEY " IS REMOVED FROM SHAFT , 5 / 8 INCH C . Place the motor on your workbench or on the floor . ( f D . Plug the cord into a properly grounded outletl ( See " Motor Specifications and Electrica Requirements " Section . ) Notice the rotation _ , . _ _ " _ " KEY of the shaft . If it is not turningnue COUNTERCLOCKWISE , do not conti COUNTER - CLOCKWISE assembly , Contact your nearest Sears Store or ROTATION Service Center . E . Remove plug from outlet . 14
Page: 15

THESE TWO EDGES _ EVEN _ _ 5 . Fromamongthe looseparts , find thefollowing hardware : 4 CarriageBolts , 5 / 16 - 18 × 3 / 4in , long 4 Flatwashers17 / 64x 3 / 4x 1 / x16 , dia.of 4 Hex . Nuts , 5 / 16 - 18 ( appro ho _ e5 / 16 in . ) 4 Lockwashers5 . / 16in . ExternaTl ype ( approx . alia . of hole5 / t6 n . ) 6 . # lacemotoronMOTORMOUNT . . . insertbolts throughholesinMOUNTthenthroughthemotor . Install Iockwashers . and hex . nuts . Do not tighten . 7 . PositionMOTORBASEonMOTORMOUNTso theedgesofthe MOTORBASEandtheMOTOR MOUNTare even . Tighten all 4 Hex . nuts securely . MOUNTING THE FLEXIBLE SHAFT 1 . From among the loose parts find the following : 3 Pan Head Screws 8 - 32 x 3 / 8 in . long 3 Lockwashers Externat Type No . 8 2 Carriage Bolts 1 / 4 - 20 x 3 / 4 in . long 2 Hex Head Screws 1 / 4 - 20 × 1 in . long 4 Hex Nuts 1 / 4 - 20 ( approx . dia . of hole 1 / 4 in . ) 2 Washers 17 / 64 x 3 / 4 x 1 / 16 4 Lockwashers External Type 1 / 4 in . ( approx . alia . of hole 1 / 4 in . ) 2 Shaft Brackets 1 Flexible Shaft Assembly 1 Motor Connector 1 Square Key 3 / 16 x 5 / 8 long 2 . Install 3 / 16 in . square key in motor shaft keyway . Loots . oe2 . setscr . ehwe . OsTO . 3 . CONNECTOR . Line up the keyway in MOTOR _ - _ - _ - nr _ . _ _ _ j i _ f CONNECTOR with the 3 / 16 in . square key on i tl £ z " ' I - - " _ - - - _ - - - - _ i J t . eo , or Ill 4 . SlidetheMOTOROONNECTORontothemotor II ! I t ! ° l ! I1t shaft as far as it will go . SECURELY tighten 2 _ _ I I _ - - - - - - - _ I k - \ I { I It setscrews . Test setscrews by trying to slide f _ ' _ l . . = . . _ _ - - - - - - - - - - _ t \ \ I I I II motor connector off motor shaft . / _ _ / _ - " _ _ t ! li CONNIECTOR is puslted on the shaft as far as it / 1 / " " _ , _ ¢ _ _ f - _ ! - - 71i I ! l _ . _ , , S € , pop . , o = _ 8 , . o , , , oretoo , o . . , , IL _ = 3 / 8 INCH _ 5
Page: 16

SAW ARBOR MOTOR END d _ - - . END 5 . Removetheplasticcoversfromtheendsof the SHAFTHOUSING . 6 . Push the saw arbor end of the flexible shaft out of the SHAFT HOUSING until it ise approximately 1 inch above the end of th SMALL FERRULE . PULL FLEXIBLE SAW ARBOR END SHAFT OUT 1 " L _ [ © O 7 . Insert the flexible shaft assembly through thehehe opening in the side of the saw base . Line up tt SQUARE END of the FLEXIBLE SHAFTwith square hole in the arbor shaft , holding square end of flexible shaft insert the FLEXIBLE SHA F ] - into the square hole in the arbor as far as it wil I go . IMPORTANT : Make sure the FLEXIBLE SHAFT is inserted as far as it will go . Approximately 3 / 4 inch . SHAFT RETAINER PAN HEAD SCREW 10 - 32 x 3 / 8 iN . | 6
Page: 17

CAREFULLY ROTATE BLADE BY HAND TO LINE UP SQUARE END OF FLEXIBLE SHAFT WiTH SQUARE HOLE IN 9 . Bend the SHAFT HOUSING toward the motor MOTOR CONNECTOR as illustrated , insert end of LARGE FERRULE \ over MOTOR CONNECTOR and line upJe SQUARE END of flexible shaft with square ho in MOTOR CONNECTOR . NOTF . : ff FLEXIBLE SHAFT is not properly positioned in the square hole of the MOTOR CONNECTOR it will not be Possible to make this con nection . It may be necessary to carefully rotate the blade to line up the SQUARE END of the flexible shaft with the square hole in the MOTOR CONNECTOR . 10 . Push LARGE FERRULE as far as it will goer against the motor end cap . if it does not ent motor end cap to ferrule bead , rotate saw blade while pushing ferrule toward motorto permitthe square ends of the core to enter their squarebe mating holes deep enough to allow ferrule to correctly positioned . 11 . Assemble upper and lower shaft bracket by inserting 1 / 4 - 20 x 3 / 4 carriage bolts in upper and lower square holes on the saw base rear rpanelt , and then through the slotted hole in the shaf brackets . AssembJe 17 / 64 x 3 / 4 x 1 / 16 washe External Type Lockwasher , and 1 / 4 - 20 Hex Nut . Finger tighten . 12 . POsition the upper and lower shaft brackets hsoe they wrap around the LARGE FERRULE on t SHAFT HOUSING . Bottom bracket should just contact and support LARG E FERRULE . Tighten nuts that hold the shaft b rackets to the saw base . 13 . Assemble two 1 / 4 - 20 x 1 in . Hex Head Screws , External Lockwashers , and ! / 4 - 20 Hex Nuts to clamp upper and lower brackets together . Do . not tighten . 17
Page: 18

14 . With end of LARGE FERRULE inserted into recess in motor end cap tighten 2 Hex Head nutsbe on shaft brackets . LARGE FERRULE must pushed against the motor end ca p as far as it wil I go . Tighten nuts but do not OVERTIGHTEN . The shaft brackets hold the LARGE FERRULE in place . Nuts should be securely tightened to prevent movement . Overtightening may cause damage to the LARGE FERRULE . _ _ BEAD ON FERRULE MUST CONTACT MOTOR END CAP IMPORTANT : The LARGE FERRULE should be centered over the MOTOR CONNECTOR ( now located Inside of LARGE FERRULE ) , to prevent the MOTOR CONNECTOR from contacting the LARGE FERRULE . 15 . Carefully turn saw blade by hand to make sure MOTOR CONNECTOR does not hit LARGEe FERRULE . - If they are . in contact , it will caus a noise and cause resistance to rotation , 16 . If the MOTOR CONNECTOR does hit the LARGE FERRULE loosen the nuts holding the shaft brackets to the saw base , and the nuts holding the LARGE FERRULE in the shaft brackets . Adjust the brackets and the LARGE / FERRULE until the LARGE FERRULE is MOTOR z centered and is not hit by the MOTOR CONNECTOR LARGE MOVE BRACKETS UP OR CONNECTOR . FERRULE DOWN SO THAT MOTOR CONNECTOR INSIDE DOES NOTE : It may be necessary to raise or lower NOT HIT FERRULE . motor on motor mount slightly . Be sure to reposition shaft brackets as required . 17 . Tighten nuts . ATTACHING AND ASSEMBLING TABLE EXTENSIONS From among the loose parts find the followings ) hardware : ( ( _ uantity indicated is for 2 extension HARDWARE FOR INSTALLING EXTENSIONS TO SAW TABLE Ref . No . Description Qty . 1 Hex Hd . Screw , 5 / 16 - 18 x 1 - 1 / 4 . . . . . . 8 2 Flat Washer ( Dia . of Hole 11 / 32 ) . . . . . 8 3 External Lockwasher , 5 / 16 _ . . . . . . . . . . . 8
Page: 19

4 . Lineupfront andtopof theextensionwiththe front and top of the table . Usea combination square to line - up these edges . SLIGHTLY TIGHTENnutswithawrench . CHECK WITH SQUARE AT 2 PLACES MARKED WITH " X " ii 5 . tf adjustment _ s necessary you should tap the extension into position using a hammer and a block of wood . Then firmly tighten nuts . BLOCK OF WOOD : \ \ JAM NUT MOUNTING SWITCH 5 / t6 - 18 1 • From among loose parts find the following : " _ 8 / LOCKWASHER 2 Hex Head Screws 5 / 16 - 18 x 3 / 4 in . long @ - _ , 8TH HOLE 2 Flatwashers ( alia . of hole 21 / 64 in . ) w _ 2 External Lockwashers 2 Hex Nuts 5 / ! 6 - 18 2 . Insert two 3 / 4 inch screws through two flat washers then through holes in switch . % ' _ - ' - - WASH ER 3 . Insert screws through holes eight and ten in front t fence guide bar as illustrated • HEX HEAD SCREW 5 / 16 - 18 x 3 / 4 IN . 4 . Install two Iockwashers and nuts . Tighten nuts . INSTALLING RiP FENCE GUIDE BARS LEFT SiDE OF FRONT GUIDE BAR 1 . From among the loose parts find the following ( GUIDE BAR IS TO BE hardware : 7TH HOLE TURNED END FOR END 3RD HOLE AFTER SCREWS ARE 2 Hex Plead Screws , 5 / 16 - 18 x 1 - 3 / 4 in . long INSTALLED ) 2 Hex Head Screws , 5 / 16 - 18 x 1 in . long 4 External Lockwashers , 5 / 16 in . ( approx . dia . of hole 5 / 16 in . ) 4 Hex Nuts , 5 / 16 - 18 ( approx . dia . of hole 5 / 16 in . ) 2 SpaceFs , 3 / 4 in . dia . x ! / 2 in . long 2 Self - threading nuts 1 Fence Guide Bar Rod SCREW 5 / 16 - 18 x 1 - 3 . / 4 IN . 2 . Lay guide bars on saw table , NOTE : The various holes in the bar allows them to be positioned on this saw and also makes them adaptable to other models . 3 . Insert a 1 - 3 / 4 inch long screw through the THIRD hole IN THE FRONT BAR as illustrated • . . Insert another 1 - 3 / 4 inch long screwthrough the SEVENTH hole in bar . 4 . Place spacers on screws . 19
Page: 20

5 . Turn front bar end for end and insert bo } tsof through holes in middle and on right sides front of saw table as illustrated . . . install Iockwashers and nuts . DON'T SCREW NUTSthe ON ALL THE WAY . just get them started on screws . 4TH OR 5TH 2ND HOLE _ " SELF - THREADING NUT HOLE 6 . Insert 1 in . long screws in SECOND and FOURTH or FIFTH holes of rear bar and attach to table the same way as front bar . 7 . Insert ends of FENCE GUIDE BAR ROD FENCE GUIDE through holes in bars as illustrated . BAR ROD NOTE ; The ends of the RODare notthreaded , . the SELF THREADING NUTS will cut threads on the rod as they are screwed on . Just start nuts onto ends of rod . 8 . Hold rod with one hand and with a 1 / 2 in . wrench or pliers start screwing on ONE of the nuts only A TURN OR TWO . . . screw on other nut the same way . 9 . Using TWO 1 / 2 in , wrenches or pliers tighten both of the nuts , . f / 10 . Slide the bars so that screws are in the M I DDLE of the slotted holes , 11 . Lift rip fence lock lever and position rip fencear over miter gauge groove , holding up the re end while engaging front end witl - ; bar . . , lower fence onto table ,
Page: 21

8 THICKNESSES 12 . Raise blade all the way up . OF PAPER 13 . Carefully move fence against blade . 14 . Move front bar until " 0 " mark on rip scale is approximately in line with indicator . 15 . Move FRONT bar upwards until fence is approximately 1 / 32 in . above table . . , tighten screw at left end of bar . NOTE : Fold a piece of newspaper making 8 thicknesses and place between rip fence cande table to act as a spacer . This will ho _ d the fen off of the table approx . 1 / 32 in . 16 . Adjust rear bar so that the fence is approximately 1 / 32 in . above table . . , make sure it is square with fence guide bar rod . . , tighten screw at end of bar . 17 . Be sure top surface of extension is PARALLEL to top surface of rear guide bar . 8THICKNESSES OF PAPER 18 . Move fence to RIGHT edge of table . . , make sure it is approx . 1 / 32 in . above table at front and rear and tighten screws . / ALIGNING RIP FENCE " _ - - _ The fence should side easily along the bars dande always remain in alignment ( para el to sawbla and miter gauge grooves ) . The alignment is rnaintained by a spring underneath the rip fence which bears against the front guide bar . TO move the fence , loosen the lock handle and grasp the fence with one hand at the front .
Page: 22

For very close adjustments , grasp the guide bar with both hands and move the fence with your thumbs . \ Place fence on saw but DO NOT LOCK IT . Move the REAR END of the fence slightly to the rig ht or left . . . when you release it , the fence should " spring " back to its original position . If it does not , the spring pressure must be INCREASED . 1 . Loosen the screws . 2 . Move Spring slightly toward front of fence . NOTE : Applying a coat of paste wax to the rails will allow fence to be moved more easily . If the fence does not slide easily along the bars , the pressure of the spring can be REDUCED . SPRING 1 . Loosen the screws . 2 . Move spring slightly toward rear of fence . . . tighten screws . WARNING : BE SURE TO PUSH LOCK LEVER ALL THE WAY " DOWN UNTIL THE LEVER RESTS ON THE STOP BEFORE USING THIS RIP FENCE . SLIDE SPRING TO ADJUST PRESSURE The rip fence lock lever when locked down should hold the rip fence securely , it should not be difficult to push down and lock . ADJUST | NG NUT If lock lever does not lock fence securely . . . . / 1 . Raise lock lever . / FENCE HEAD 2 . Tighten the adjusting nut using a small / screwdriver until the lever , when locked , holds the rip fence securely . ff lock lever is difficult to push down . . . 1 . Raise lock lever _ 2 . Loosen the adjusting nut using a nsrnall screwdriver until the lever is easy to push dow and holds the rip fence securely . 22
Page: 23

HEX SCREWS FENCE HEAD 3 , The rip fence must be PARALLEL with the sawblade and miter Gauge grooves Move fence until it is along side of groove . E ) o NOT LOCK IT . It sPiou / d be parallel to groove , If it rs not ; A . Loosen the two " Hex Head Screws . " B . Hold fence head tightly against bar . . move end of fence so that it is parallel with groove . C . Alternately tighten the screws , \ ADJUSTING RiP SCALE iNDiCATOR 1 . Turn ELEVATION HANDWHEEL clockwise until blade is up as high as it will go . IMPORTANT : BLADE must be SQUARE ( 90 ° ) to TABLE , in order to ALIGN rip fence , 2 . Using a rule , position fence on right side of sawblade 2 in . from the sides of the teeth . . . tighten lock handle , 3 . Loosen screw holding the indicator . . , adjust so that it points to " 2 " on the rip scale . . , tighten screw . NOTE : If you cannot adjust indicator so that it poin ts to " 2 " , loosen the screws holding the front guide bar and move the guide bar . \ \ iNSTALLING BLADE GUARD SPREADER SUPPORT PLATE 1 . From Among the loose parts find : NUT 4 Truss Head Screws 1 / 4 - 20 x 3 / 4 in . long SPREAOER CLAMP 2 Hex Socket Setscrews 1 / 4 - 20 x 1 in . long NUT 4 Washers 17 / 64 x 5 / 8 x 1 / 32 6 Lockwashers 1 / 4 in . External Type ( approx , die . of hole 1 / 4 in . ) 2 Hex Head Nuts 1 / 4 - 20 FLAT WASHER EXT . 1 / 4 IN . 17 _ 41N { approx . die . of hole 1 / 4 in . ) FLAT WASHER IN . HOLE 2 Wing Nuts 1 / 4 - 20 EXT . IN IN . ( aprox , dia . of hole 1 / 4 in . ) HEX NUT / EXT , ! / 4 tN . 1 Spreader Support FLAT WASHER NUT 17 / 64 IN . HOLE 1 Plate Nut , OCKET HEAD SETSCREW 1 If _ . LONG 1 Spreader Clamp EXT . 1 / 4 IN . HEX NUT 1 Spreader Bracket 23
Page: 24

BLADE ESQUARE WITH TABL WARNING : TO AVOID INJURY DUE TO ACCIDENTAL START , TURN SWITCH " OFF " AND REMOVE PLUG FROM POWER SOURCE OUTLET . 2 . MAKE SURE THE BLADE IS ALL THE WAY UP AND SQUARE WITH THE TABLE . RIP FENCE 3 . Position SPREADER SUPPORT on rod behind GUIDE BAR the rip fence guide bar , / SPREADER SUPPORT POSITIONED ON ROD BEHIND RIP FENCE GUIDE BAR \ \ 4 . Assemble the 7 / 8 in . long setscrews , nuts . Iockwashers and washers to the SPREADER \ SUPPORT BRACKET and slip the nuts into the slot in the spreader support . 5 , Locate spreader support and bracket on rod . 1 / 16 SPREADER SUPPORT _ inch behind the fence guide bar . . . . _ - _ - _ BRACKET 6 , Finger tighten ONLY THE HEX NUTS . VIEW LOOKING DOWN FROM TOP 7 . Lay a piece of flat straight wood and a square on saw table and rotatethe SPREADER SUPPORT until the bracket is aligned with square . B . 24
Page: 25

sPACE EQUAL TO APPROX , 3 THICKNESSES OF PAPER KERF WOOD . - _ J _ : _ . _ , _ BLADE WARNING : AVORD iNJURY . f . _ - . _ . . . . . _ . - : L . . . . ACCIDENTAL START , TURN SWITCH OFF AND , " _ " _ - - . . . . . . . . . . . . . . . . . . . . . . - REMOVE PLUG FROM POWER OUTLET . \ . _ [ _ ' C : 3 ; : . : CCi _ - - _ iMPORTANT : The SPREADER must always be y = am _ - - the cut ( KERF ) made by the sawblade , sPR _ . _ . . . . . . . . _ : _ _ _ : PARALLEL to the sawb , ade and in the MIDDLE of - - - - - _ i _ ! _ _ i _ _ NOTE : The spreader is thinner than the width of the _ / l _ ] i ! i " ' z2 _ . _ KERF by approximately six thicknesses of paper . SPACE EQUAL TO APPROX . LOOKING DOWN ON SAW 3 THIC KN ESSES OF PAPER 1 . Make two folds in a small piece ( 6 x 6 in , ) of ordinary NEWSPAPER making athrees thicknesses . The folded paper will be used a " spacing gauge " . / ; 1ANT , K , CKBACK 2 , Install TRUSS HEAD SCREWS , SPREADER t / _ | / [ ! PAWLS CLAM P and WING NUTS to spreader bracket . Do t t ft , J / 1 . OLD * OOD net tighten wing nuts . Place spreader between J t , I _ _ / t TIGHTLYAGAINSTI spreader clamp and bracket . Move forward until all three are in line . TIGHTEN WING NUTS . 3 . Lift up both ANTIKICKBACK PAWLS . . . inserte one of the setscrew wrenches or a pencil in th notches to hold the pawls out of the way . 4 . Lay a piece of straight flat wood against the sawblade . Insert folded paper between spreader and strip of wood . 5 , MAKE SURE THE HEX NUTS UNDERNEATH ARE LOOSE , 6 . Hold the spreader tightly against the wood ande . make sure the wood is against the saw blad _ . _ _ HOLD SPREADER TIGHTEN THE HEX NUTS . _ F _ TIGHTLY AGAINST WOOD WING NUT I This will align the spreader in the middle of the / SPREADER cut ( KERF ) made by sawblade . BRACKET SPREADER 7 . Lower the antikickback pawls The end of the CLAMP right hand ( viewed from front of saw ) pawl shouldlot pawt strikes the metal of the insert , reposition tl move down and clear the end of the small s sp reader support . provided in the insert . If end of the right hang ADJUSTING MITER GAUGE NOTE : The slots for the stop pin and the graduations are manufactured to very close tolerances which provide accuracy for average woodworking . In some cases where extreme accuracy is required , when making angle cuts , for example , make a trial cut and then recheck it . , ' pin " OUT . 1 , Loosen the " knob and pull stop INDICATO BLOCK necessary ,
Page: 26

4 . If the head is not square with the bar , adjustments are required . A . Loosen the " knob " ( 1 ) and the " two screws " ( 2 ) . B . Position the HEAD square with the BAR using a combination square . C . PUSH the STOP PIN into the slot in the head at " 0 " . . . push the pin into the slot and twist it . Lock the knob . D . Recheck with the soluare . If the head is still not square , loosen the screws ( 2 ) and readjust t . he iNDiCATOR BLOCK . E . With the head square with the barand the pun pushed into the slot adjust the pointer ( 3 ) to point to " 0 " . F . The miter gauge head must rest on top of the bar without being able to move up and down • . , yet . it must swivel freely . G . The swiveling movement of the head can be adjusted by tightening or loosening the setscrew ( 4 ) . . . using the 1 / 8 in . setscrew wrench . 1 / 8 IN . SETSCREW NOTE : The setscrew is located inside of the WRENCH head . To reach it , swivel the head to 60 degrees and turn the miter gauge upside down . ASSEMBLING HOLD - DOWN Locate the clamp assembly , support rod , two wing screws and two washers in loose parts bag . Screw the support rod ( 1 ) tightly into the hole in the miter gauge head . Position the clam p assembly ( 2 ) on the handle and rod . . install washers ( 3 ) an ( _ wing screws ( 4 ) . NOTE : The sma ! l knob ( 5 ) on the clamp screw mustt I not turn . Check nut underneath it . . . it must betigh against the knob . Use a 1 / 2 inch wrench to tighten it . PLUGGING IN MOTOR 1 . From among the loose parts , find two wire tieS . 2 . Route motor cord along right side of cabinet and snap ties in 1 / 4 " hole in stde of cabinet . Secure two cords in wire ties . 3 . Plug motor cord into outlet on side of switch box . WIRE TIES PICTURE CLARITY 26
Page: 27

GETTING TO KNOW YOUR SAW 9 SAWBLADE 8 TABLE INSERT MITER GAUGE 10 EXACT - I - CUT ANTIKICKBACK LOCK HANDLE PAWLS RIP FENCE HOLES FOR ATTACHING FACING 6 MITER GAUGE , TI TLOOK . A " AOBLE , , UNO . . EAT , , \ 2 ELEVATION HANDWHEEL 3 TILT HANDWHEEL 1 ON - OFF SWITCH 1 ON - OFF SWITCH CAUTION : Before turning switch on , make sure the blade guard is correctly installed and operating properly . The On - Off Switch has a locking feature . TTHIS FEATURE IS INTENDED TO PREVEN UNAUTHORIZED AND POSSIBLE HAZARDOUS USE BY CHILDREN AND OTHERS . A . TO turn saw ON . . . stand to either side of the blade never in line with it . . . insert finger KEY under switch lever and pull END of lever out . ( YELLOW PLASTIC ) Do not cycle the motor switch on and off rapidly , as this may cause the sawblade tor . loosen . In the event this should ever occu allow the sawblade to come to a cornplete stop and retighten the arbor nut normally , note excessively . Never leave the saw while th power is " ON " . B . TO turn saw OFF . . PUSH lever in . Nevere leave the saw until the cutting tool has com to a complete stop , C . TO lock switch in OFF position . . , hold switch IN with one hand . . . REMOVE key with other hand , WARNING : FOR YOUR OWN SAFETY , LOWER BLADE OR OTHER CUTTING TOOL BELOW TABLE SU RFACE . ( IF BLADE IS TILTED , RETURN IT TO VERTICAL ( 90 ° ) POSITION ) . ALWAYS LOCK THE SWITCH OFF . WHEN SAW IS NOT IN USE . . • REMOVE KEY AND KEEP IT IN A SAFE PLACE . . . ALSO . . . IN THE EVENT OF A POWER FAILURE ( ALL OF YOUR LIGHTS GO OUT ) TURN SWITCH OFF . . . LOCK IT AND REMOVE THE KEY . THIS WILL PREVENT THE SAW FROM STARTING UP AGAIN WHEN THE POWER COMES BACK ON . 27
Page: 28

MITER GAUGE . . head is locked in position 8 2 ELEVATIONHANDWHEEL . . . elevates or for crosscutting or mitering by tightening the lowers the blade , Turn clockwise to elevate . . lock knob . ALWAYS LOCK IT SECURELY counterclockwise to lower . WHEN IN USE . NOTE : Any time sawblade has been elevatedill There are slots for the stcp pin at the 45 deg tee to 2 - 5 / 8 inches or higher above the table it w right and left positions for conveniently setting be necessary to lower the blade by turning the the Miter Gauge to cut miters , elevation handwheel 5 turnscounterclockwise NOTE : The slots for the stop pin and the before tilting to bevel . graduations are manufactured to very gclosee 3 TiLT HANDWHEEL . . . tilts the blade for bevel tolerances which provide accuracy for avera cutting . Turn clockwise to tilt toward left woodworking . In some cases where extreme counterclockwise to tilt toward vertical . accuracy is required , when making angle cuts , When the blade is tilted to the LEFT as far as it for example , make a trial cut and then recheck will go , it should be at 45 ° to the table and the it . bevel indicator should point 45 ° , If necessary , the miter gauge head can then be NOTE : There are LIMIT STOPS on the saw swiveled slightly to compensate and then which prevent the blade from tilting beyondee locked . 45 ° to the LEFT and 90 ° to the RIGHT . ( S Slots are provided in the miter gauge for " Adjustments " section " Blade Tilt , or attaching an AUXILIARY FACING to make it Squareness of Blade to Table " ) . easier to cut long pieces . Be positive facingof does not interfere with the proper operation 4 TILT LOCK HANDLE . . . locks the blade in rthen the sawblade guard . desired tilt position . To loosen tu Select a suitable piece of smooth tstraighth counterclockwise . Push handle in and turn itto wood . . ari ] l two holes and attach it wi another position if necessary in order to screws . tighten or loosen . NOTE : When bevel crosscutting , attach facing ! MPORTA . NT : Be sure handle Is hanging in the so that it extends to the right of the miter gauge DOWN position before tilting blade . If it Is and use the miter gauge in the groove to the pointing to the 1 o'clock position it may jam ong underside of the table and bend the lockin right of the blade . bolt , ) LD DOWN 5 RIP FENCE . . . is locked in place by ttighteninghe CLAMP the lock knob . To move the fence , loosen knob and grasp the fencewith one hand at the LOCK fro nt . Holes are provided in the rip fence for attaching a wood facing when using the dado head , or molding head . Select a piece of smooth straight wood approx . ARY 3 / 4 " thick , at least as long as the rip fence , and FACING STOP PIN 45 ° SLOT at least 7 - 1 / 2 " wide ( high ) to permitclamping FOR STOP PIN of featherboards . Attach it to the fence with three Round Head 7 BLADEGUARD must always be in place and # 10 Wood Screws 2 in . long . To remove the work ng properly for all thru - sawing cuts . That facing , loosen the screws , slide the facing is , all cuts whereby the blade cuts compete y forward and pull the screws through the round through the workpiece . holes . To remove the guard for special operations , If you are making a rip type cut in material loosen the wing nuts and slide the guard off of thinner than 3 / 16 in . while the fence is the rod . DO NOT DISTURB THE SETTING OF positioned over the depressed area of table THE ROD . extension , the facing should be attached to the When rep acing the guard , make sure the PIN fence so thatthe bottom edge touches the top in the rod engages with the NOTCH n the surface of the extension . In this case , the spreader support . Make sure wing screws are facing must be shorter than the fence . This will tightened securely . prevent thin material from sliding under the rip 8 TABLE INSERT is removable for removing or fence . installing blades or other cutting tools . WOOD FACING DUE TO INJURY _ G : TO AVOID ; H " OFF " POWERNG VI surface . d pull toward ROUND HEAD / # 10 WOOD SCREWS 28
Page: 29

BLADE GUARD NOT SHOWN FOR PICTURE CLARITY NEVEROPERATETHE SAW WITHOUTTHE . . . . . . . PROPERINSERTIN PLACE . USE THE SAW BLADEINSERTWHENSAWING , . . USE THE COMBINATION DADO MOLDING INSERT ( 9 - 22271 ) WHEN DADOING OR MOLDING . BLOCK < . _ > il / : ) R NUT LOOSE COLLAR ARBOR SCREW _ @ _ ARBOR NUT TEETH POINTING TO . - - , . - _ FRONT OF SAW t % . . . 9 REMOVING AND INSTALLING SAWBLADE . 10 EXACT - I - CUT WARNING : TO AVOID INJURY DUE TO The " yellow " plastic disc imbedded in the table ACCIDENTAL START , TURN SWITCH " OFF " in front of the sawblade , is provided fol AND REMOVE PLUG FROM POWER marking the location of the " sawcut " on the SOURCE OUTLET BEFORE REMOVING OR workpiece . iNSTALLiNG SAWBLADE . A . Check disc . . . if it is above table surface A . Raise Blade Guard . . . remove insert . place a piece of hardwood on top of it and ta ! : it down . B . To REMOVE blade , place a block of wood against front of blade . _ . PULL arbor wrench B . With blade 90 ° ( square to table ) cut off - " toward you to LOOSEN arbor nut . piece of wood . C . Pull miter gauge back until wood isover disc Using very sharp pencil , mark a line on disc D . With miter gauge in right hand g roove , follow same procedure and mark another line or disc . E . These lines indicate the " path " of the cu ' / / , _ ( kerf ) made by the sawblade . . . . . . / / / _ \ _ ' - F . When cutting the workpiece , line up mark or _ P , _ I _ # ( _ H / / / / / / / _ L _ workpiece With line on disc . i ! fF y usethehold - owcn . mp ( optionaaclcessory ' BOR NU . " i _ J \ \ \ ' on the miter gauge for greater accuracy . WOSOLDOCK j / / @ BLADE GUARD NOT SHOWN FOR PICTURE CLARITY _ P _ I _ J _ _ I _ C . TO TIGHTEN arbor nut , place a block of _ _ _ _ _ . . . . - - _ j _ r _ wood against rear of blade . . . PUSH wrench _ - ' - _ - - _ I _ I _ JJdl _ _ ' _ away from you . _ - _ \ iJ _ _ , _ When installin _ l the blade . . . make sure the _ _ . J _ - _ - - - - _ _ _ . _ . _ . , _ _ _ Z towa , hrd , eroootfthseaw teeth are pointing . andthatthebladeandcollarsareclean and _ _ , _ / . . - _ _ _ - ' P - free from any burrs . " _ _ ( ' _ - ' _ " - " - The HOLLOW side of the collar must be _ y _ _ _ L _ _ . _ _ - _ _ _ against the blade . BLADE GUARD NOT SHOWN FOR PICTURE CLARITY Always tighten the arbor nut securely . F NOTE : When using the Dado or Molding Head , it s not necessary to install the loose collar . To replace insert . Place insert into insert opening in table and push toward rear of saw to engage spring clipw . and until keyslot in insert will drop over scre _ " , ¢ Do not tighten screw to the point where it will deflect the insert .
Page: 30

OPERATION BASIC SAW THESE EDGES MUST BE PARALLEL 3 / 4 PLYWOOD WORK HELPERS Before cutting " any wood . on , , your saw , study all of the " Basic Saw Operations . \ Notice that in order to make some of the cuts , it is \ necessary to use certain devices " Work Helpers " PUSH BLOCK like the Push Stick , the Push Block and the Auxiliary Fence / Work Support , which you can make yourself . 3 / 8 2 - 1 / 2 After you have made a few practice cuts , make upke these " helpers " before starting any projects . Ma the " Push Stick " first . 3 / 8 I SLIGHTLY LESS THAN 318 PLYWOOD NOTE : All dimensions in inches THICKNESS OF WORKPIECE AUXILIARY FENCE / WORK SUPPORT UP TO 3 / a ' " Make one using a piece of 3 / 8 in . and 3 / 4 in . plywood . Fasten together with glue and 1 - 5 / 8 woodscrews . 1 NOTE : Since the Push Block is used with the Auxiliary Fence , the 4 - 3 / 4 in . dimensions must _ ) e held identical on both the pieces . 45 ° NOTCH AUXILIARY FENCE / 314 PLYWOOD WORK SUPPORT NOTE : All dimensions in inches 27 PUSH STICK AND PUSH BLOCK Make the Push Stick using a piece Of1x2 , or ripone 1 - 1 / 4 from a wide board , say 11 - 1 / 2 in . wide , and set the rip fence 9 - 7 / 8 in . from the sawblade . Make the Push Block using a piece of 3 / 8 in . and 3 / 4 in . plywood . THIS FACE AND THISLLEL The small piece of wood 3 / 8 in . x 3 / 8 in . x 2 - 1 / 2 in . EDGE MUST BE PARA ' should be GLUED to the plywood . . . DO'NOT USE N NAILS . This isto prevent dulling the sawblade in the 3 / 8 PLYWOOD " \ 5 - 1 / 2 event you mistakingly cut into the push block . NOTE : All dimension in inches _ % _ / " Position the handle in the centerof the plywood and fasten together with glue and woodsorews . USING THE MITER GAUGE 6 . Do not stand directly infront of the blade in caseht THE MITER GAUGE IS USED VWHENEL of a THROWBACK ( Small cut - off piece caug CROSSCUTTING , MITER CUTTING , BE by the back of the blade and thrown toward the CUTTING , COMPOUND MITER CUTTING , operator ) . Stand to either side of the blade . DADOING and when RABBETTING AND MOLDING across the end of a narrow workpiece . 7 . Keep your hands clear of the blade and out of the path of the blade . WARNING : FOR YOUR OWN SAFETY , ALWAYS OBSERVE THE FOLLOWING SAFETY 8 . If blade stalls or stops while cutting , TURN PRECAUTIONS IN ADDITION TO THE SAFETY SWITCH OFF before attempting to free the INSTRUCTIONS ON PAGES 2 , 3 , and 4 . blade . 1 . Never make these cuts freehand ( without using 9 Do not reach over or behind the blade to pull the the miter gauge or other auxiliary devices ) workpiece through the cut . . , to support long or because the blade could bind in the cut and hea _ workpieces • . • to remove cut - off pieces of cause a KICKBACK or cause your fingers or mate = ' ial or FOR ANY OTHER REASON . hand to slip into the blade . Use . 3 . Remove rip fence from table . remove small pieces of cut - off material th _ Ly become TRAPPED inside the blade gut ihile the saw is RUNNING . THIS COULD EN _ GER YOUR HANDS or cause a KI ( _ CK . Turn e saw OFF . After the blade has stopped turning , lift the guard and remove the piece . would increase the hazard potential . 3O
Page: 31

WORKPIECE CROSSCUTTING ! CROSSCUTTING is known as cutting wood across the grain , at 90 ° , or square with both the edge and the flat side of the wood . This is done with miter r I JtI l gauge set at " 0 " . TABLE The graduations on the miter gauge provide accuracy for average woodworking . In some cases where extreme at : curacy is required , when making angle cuts , for example , make a trial cut and then . recheck it with an accurate square , or protractor If necessary , the miter gauge head can be swiveled slightly to compensate for any inaccuracy . NOTE : The space between the miter . gauge barandng the groove in the table is held to a minimum duri manufacturing . For maximum accuracy when using the miter gauge , always " favor " one side of the groove in gthee table , in other words , don't move the miter gau from side to side while cutting , but keep one side of the bar riding against one side of the groove . NOTE : Glue a piece of sandpaper to the face of the miter gauge head . This will help prevent the workpiece from " creeping " while it is being cut . The Hold - Down Clamp included with 113.241690 groove , hold the workpiece firmly against the miter should be used on the miter gauge for greater gauge head with your left hand , and grip the lock handle with your right . accuracy . The miter gauge may be used in either of the When using the RIGHT Hand groove , hold the grooves in the table . Make sure it is locked . workpiece with your right hand and the Iockhandle with your left hand . When using the miter gauge in the LEFT hand \ AUXILIARY FENCE / When cutting long workpieces , invert AUXILIARY WORK SUPPORT FENCE / WORK SUPPORT and position it on top of the guide bars to support the work pieces as near toy the end as possible . If this does not adequatel support the workpiece , you can make a simple support by clamping a piece of plywood to a sawhorse , Use the Hold - Down Clamp included with 113.241690 on miter gauge for greater accuracy . \ REPETiTiVE CUTTING REPETITIVE CUTTING is known as cutting a quantity of pieces the same length without having to mark each piece . 1 . Use the Stop Rods ( optional accessory ) only for cutt ng dup icate pieces 6 in . long and longer . 2 , Follow all Safety Precautions and Operational _ Instructions for Cross Cutting . When making repetitive cuts from a long workpiece . Use I WORK SUPPORT
Page: 32

\ \ 1 . NEVER USE THE RIP FENCE'AS A LENGTH \ STOP BECAUSE THE CUTOFF PIECE COULD \ BIND BETWEEN THE FENCE AND THE BLADE CAUSING A KICKBACK . BLOCK 2 . When making repetitive cuts shorter than 6 in . . clam p a block of wood 2 in . long to the table to act as a length stop . Do not clamp directly to the bottom edge of the table because the ' swivel of the clamp will not grip properly , Place a small block of wood between the bottom edge of the table and the " ( 3 " clamp . CAUTION : When clamping the block , make hsuree that the end of the block is well in front of t sawblade . Be sure it is clamped securely . 3 . Slide the workpiecealong the miter gauge until it touches the block . . , hold it securely or clam _ > hit with the Hold - Down Clamp included wit 113.241690 . stick . . . DO NOT ATTEMPT TO PICK IT UP AS 4 Make the cut . . , pull the workpiece back . . . push THIS COULD ENDANGER YOUR HANDS . the cut off piece off the table with a long push MITER CUTTING TABLE MITER CUTTING is known as cutting wood at an angle other than 90 ° with the edge of the wood . Follow the same procedure as you would for crosscutting . Adjust the miter gauge to the desired angle , and lock it . The miter gauge may be used in either of the grooves in the table . When using the miter gauge in the LEFT Hand groove , hold the workpiece firmly against the miter kgauge head with your left hand , and grip the lock nob with your right . When using the RIGHT hand groove , hold the workpiece with your right hand and the knob with your left hand . Use the Hold - Down Clamp included withcy . 113.241690 o n the miter gauge for greater accu ra BEVEL CROSSCUTTING BEVEL CROSSCUTTING is the same as crosscutting except that the wood is also cut at an angle . . . other than 90 ° with the flat side of the wood NOTE : Anytime saw blade has been elevated to 2 - 5 / 8 inches or higher above the table , it will be necessary to lower the blade by turning the elevation handwheel 5 turns counterclockwise ' \ before tilting to beVel Adjust the blade to the desired angle . \ theEFT L because the blade and the Use the AUXILIARY FENCE / WORK SUPPORT for workpiece as near to the end as possible . Use the Hold - Down Clamp included with 113.241690 on the miter gauge for greater accuracy . 32
Page: 33

made at an angle other than 90 ° to both the edg _ COMPOUND MOTER CUTTING and the flat side of the wood , COMPOUND MITER CUTTING is a combination of Adjust the miter gauge and the blade to the desirec miter cutting and bevel crosscutting . The cut is angle . , . Make sure miter gauge is locked . USING THE RmPFENCE 5 . Have blade extend approximately 1 / 8 in . abow RIPPING , BEVEL RIPPING , PLOUGHING , top of workpiece . Additional blade exposun MOLDING , RESAWING AND RABBETING are would increase the hazard potential . performed using the RIP FENCE together with the AUXILIARY FENCE / WORK SUPPORT , PUSH 6 . Do not stand directly in front of the blade in casq , STICK OR PUSH BLOCK . of a KICKBACK . Stand to either side of th blade . WARNING : FOR YOUR OWN SAFETY , ALWAYS OBSERVE THE FOLLOWING SAFETYETY 7 . Keep your hands clear of the blade and out c PRECAUTIONS iN ADDITION TO THE SAF the path of the blade . iNSTRUCTIONS ON PAGES 2 , 3 , and 4 . 8 . If the blade stalls or stops while cutting . TURf 1 . Never make these cuts FREEHAND ( without SWITCH OFF before attempting to free th _ using the rip fence or auxiliary devices when blade . required ) because the blade could bind in the 9 . Do not reach over or behind the bladeto pull th , cut and cause a KICKBACK . workpiece through the cut . . , to support long o 2 . Always lock the rip fence securely when in use . heavy workpieces . . , to remove small cut - c1I pieces of material or FOR ANY OTHE 3 . Remove miter gauge from table . REASON . 4 . Make sure blade guard is installed for all thru - ! 0 . Do not pick up small pieces of cut - off materi _ sawing type cuts . Replace the guardof from the table . REMOVE them by pushing ther IMMEDIATELY following completion OFF the table with a long stick . Otherwise the resawing , rabbeting , dadoing , or molding could be thrown back at you by the rear of th operations . blade . Frequently check the action of thehe 11 . Do not remove small pieces of cut - off materi _ ANTIKICKBACK PAWLS by passing t that may become TRAPPED inside the blad workpiece alongside of the spreader while saw guard while the saw is RUNNING . THIS COULI is OFF . ENDANGER YOUR HANDS or cause Pull the workpiece TOWARD you . If the _ PAWLS KICKBACK . do not DIG into the workpiece and HOLD it . . Turn the saw OFF . After the blade has stoppe the pawls must be SHARPENED . See turning , lift the guard and remove the piece . " Maintenance " section . WORKPIECE IF - . RiPPiNG L " ) RIPPING is known as cutting a piece of wood with TABLE the grain , or lengthwise . This is done using the rip fence . ALWAYS SUPPORT LONG WORKPIECES Position the fence to the desired WlDTH OF RIP and lock in place . Before starting to rip , be sure A . Rip Fence is parallel to sawblade . B . Spreader is properly aligned with sawblade . C . Antikickback pawls are functioning properly . When ri pping LONG BOARDS or LARGE PANELS . always use a we rk support . . . . A simple one can be made by clamping a piece of plywood to a sawhorse . BEVEL RIPPING fWhen bevel ripping material 6 in . or narrower , useill ence on the right side of the blade ONLY . This w mounted to the left , the sawblade guard may interfere with proper use of a push stick . 33
Page: 34

When " Wl DTH OF RIP " is 6 in . and Wi DER use your RIGHT Hand to feed the workpiece until it is clear of the table . Use LEFT hand ONLY to guide the . work piece . . . do not FEED the workp ece with the left hand , When " WIDTH OF RIP " is 2 in , to 6 in . wide USE THE PUSH STICK tc feed the work . When WIDTH OF RIP is NARROWER than 2 in , . the push stick CANNOT be used because the guard will interfere . . . USE the AUXILIARY FENCE / WORK SUPPORT and PUSH BLOCK . Attach Auxi ! ! ary Fence / Work Support to rip fence with two ' C c amps . / 34
Page: 35

Feed the workpie'ce by hand along the AUXILIARY FENCE until the end is approx . 1 in . past the front edge of the table . Continue to feed using the PUSH BLOCK . Hold the workpiece in position and install the PUSH BLOCK by sliding it on top of the AUXILIARY FENCE / WORK SUPPORT ( This May Raise Guard ) - BAFFLE Narrow strips thicker than the Auxiliary Fence / Work Support may enter the guard and strike the baffle . CAREFULLY raise guard only enough to clear the workpiece . Use PUSH BLOCK to complete cut . PLOUGHING AND MOLDING MOLDING is shaping the workpiece with the grair PLOUGHING is grooving with the grain the long the long way of the workpiece , using the fence . USE way of the workpiece , using the fence . USE Featherboards and push sticks as required . Featherboards and push sticks as required . I PLOUGHIN MOLDING 35
Page: 36

RESAWING RESAWING is known as ripping a piece of wood through its thickness . Do not attempt to resawa BOWED or WARPED material . NOTE : To RESAW piece of wood wider than 3 - 3 / 8 in . . . it will hbeek necessary to remove the blade guard . . . and use tor AUXILIARY FENCE / WORK SUPPORT . ( See " W Helpers " ) . SMALL BLOCK OF WOOD Clamp it to the table so that the workpiece will SLIDE EASILY but not TILT or MOVE SIDEWAYS / without BINDING between the two fences . Do not clamp directly tc the bottom edge of the tableip 2 . MAKE FIRST PASS TO A DEPTH SLIGHTLY because the " swivel " of the clamp will not gr LESS THAN ONE - HALF THE WIDTH OF THE properly . Place a small block of wood between the BOARD ; KEEP SAME FACE OF BOARDHE bottom edge of the table and the " C " clamp . AGAINST FENCE FOR SECOND PASS AS T FIRST PASS . WARNING : FOR YOUR OWN SAFETY . . . 3 . iNSTALL BLADE GUARD IMMEDIATELY UPON I . DO NOT " BACK UP " ( REVERSE FEEDING ) WHILE RESAWING BECAUSE THIS COULD COMPLETION OF THE RESAWING OPERATION . CAUSE A KICKBACK . AUXILIARY FENCE / WORK SUPPORT CUTTING PANELS When cutting panels ( whenever fence is positionedhe outside of table surface ) , ALWAYS use t AUXILIARY FENCE / WORK SUPPORT . 1 . Unlock fence and raise rear end . 2 . Position AUXILIARY FENCE / WORK SUPPORT as shown and attach it with two " C " clamps . RABBETING RABBETING is known as cutting out a section of the corner of a piece of material , across an end oralong an edge . To make a RABBET requires cuts which do not go all the way through the material . Therefore the blade AABDET S 00F " D j / 1 . Remove blade guard . / / / RABBETING 2 . For rabbeting along an edge ( long way ofe ACROSS THE END workpiece ) as shown , add facing to rip fenc RABBETING ALONG TNE EDGE approximately as high as the workpiece is wide . Adjust rip fence and blade to required dimensions ; then make first cut with board flat onth table as any rip ( type ) cut ; makesecond cut wi workpiece On edge . Follow all precautions , safety instructions , and operational instructions as for piece to obtain thedesired width of cut . DO NOT 3 . For rabbeting across an end , for workpiece 10 - use the rip fence for rabbeting across the end , 1 / 2 and narrower make the rabbet cut w th the 4 . INSTALL BLADE GUARD IMMEDIATELY UPON board flat on the table . Using the miter gauge COMPLETION OFRABBETING OPERATION . fitted with a facing follow the same procedures Rabbet cuts can be made in one pass of the work - and instructions for cross cutting , making pieceoverthe cutterusing thedado head or molding successive cuts across the width of the work - head .
Page: 37

DADOING Instructions for operating the Dado Head ared . contained in boo _ let furnished with the Dado Hea The Recommended Dado Head is listed under o o Recommended Accessories in this manual . The arbor on the saw , is only long enough so that the widest cut that can be made is 13 / 16 " wide . It is not necessary to install the outside loose collar before screwing on the arbor nut . Make sure the arbor nut is tig ht . ALWAYS USE DADO INSERT LISTED UNDER RECOMMENDED ACCESSORIES . LOOSE : OLLA _ When using the dado head it will be necessary to remove the Blade Guard and Spreader . Use Miter Gage and follow same procedures ano Instructions for C ross Cutting . ALWAYS REPLACE THE BLADE , GUARD AND ARBOR _ SAW ARBOR SPREADER WHEN YOU ARE FINISHED DADOING . MOLDING CUTTING REMOVE SAWBLADE AND Instructions for operating the Molding Head areg INSTALL DADO HEAD . J contained in a booklet furnished with the Moldin BACK OF SAW Head . The recommended molding head is listed under Recommended Accessories in this manual CAUTION . USE FEATHERBOARDS AND PUSH STICKS , etc AS REQUIRED . Always use Molding Insert Listed Under ALWAYS REPLACE THE BLADE GUARD AND Recommended Accessories . SPREADER WHEN YOU ARE FINISHED When using the molding head it will be UnecessarytoSE MOLDING . remove the Blade Guard and Spreader . USING FEATHERBOARDS Before starting the operation ( switch " OFF " and Add 8 inch high flat facing board to the fence , the cutter below table surface ) : full length of the fence . ( a ) Install featherboards so they exert pressure on Use featherboar . ds for all non " thru - sawing " the work piece ; be positive they are secure , and operations ( when sawblade guard must be removed ) . Featherboards are used to keep the workto ( b ) Make sure by trial that the featherboards will in contact with the fence and table as shown , and stop a kickback if one should occur . stop kickbacks . Featherboards are not employed during non thru - Mount featherboards to fence and table as shown , sawing operations when using the miter gauge . so that leading edges of featherboards will support Replace the sawblade guard as soon as the non workpiece until cut is complete , and the workpieceter thru - sawing ooeration is complete . has been pushed completely past the cut / ( sawblade , dado head molding head , etc . ) with a pushstick , as in ripping . " C " CLAMPS FEATHERBOARD WORK SUPPORT 37
Page: 38

MOTOR LUBRICATmON AND MAINTENANCE NOTE : The speed of this motor canno _ be 1 . The sleeve bearings , in both end shields of the regulated or changed . motor , have been lubricated at the factory twithor correct lubricant . No other part of the mo 4 . Every effort should be made to prevent foreigned requires lubrication , material from entering the motor . When operat under conditions likely to permit saccumulationsual 2 . Re - lubricate motor bearings in accordance with of dust . dirt , or waste within the motor , a vi the instructions on the nameplate . Be sure to inspection should be made at frequent intervals . wipe off dirt or grit if present around oil hole caps Accumulations of dry dust can usually be blown to prevent any possibility of foreign material out successfully . contaminating the oil wicks that supply them bearings with oil . Use a good grade of mediu NOTE : Motors used on wood - working tools are weight mineral oil , such asautomobileengine oil , ; ) articularly susceptible to the accumulation oft SAE 2 ( 3 . sawdust and wood chips and should be blown ou or " vacuumed " frequently to prevent interferenceper 3 . If disassembly of the motor is necessary , it ashouldil - with normal motor ventilation and pro be returned to your nearest Sears retail or m operation of the centrifugally - operated starting order store jn order to prevent voiding the switch . g ua rantee . MAINTENANCE WARNING : TO AVOID INJURY , TURN ESWDTCHR " OFF " AND REMOVE PLUG FROM POW SOURCE OUTLET BEFORE MAINTAINING OR LUBRICATING YOUR SAW . \ Do not allow sawdust to accumulate inside the saw . Frequently blow out any dust that may accumulate inside the saw cabinet and the motor . FrequenUy clean your cutting tools with Craftsman Gum and Pitch Remover . A coat of automobile - type wax applied to the table will help to keep the surface clean and allow workpieces to slide more freely . If the power cord is worn or cut , or damaged in any . i j way , have it replaced immediately . Make sure the teeth of the ANTIKICKBACK pawls are always sharp . To sharpen : 1 . Identify the dull tooth or teeth . Remove blade guard . 2 . Rotate pawl toward rear of spreader so that teeth are above top of spreader . ¸ ¸ ¸ ¸ 38
Page: 39

LUBRiCATiON eventually age and harden so that it witl not prov | € The following parts should be oiled occasionally with SAE No . 20 or No . 30 engine oil . an adequate oil film between the core and cas _ r liner and must be replaced . 1 . Tilt screw threads and pivot nut . ( First Clean with Craftsman Gum & Pitch Remover . ) LUBRICATmON PROCEDURES 2 . Elevation screw threads and pivot nut . ( First 1 Remove the core from the casing , clean the co Clean with Craftsman Gum & Pitch Remover . ) by washing with kerosene or an approve solvent . 3 . Cradle bearing points . 2 . Dry the core . 4 . Bearing points in guard assembly , miter gauge and rip fence . 3 . Inspect the core for worn or broken wires , if co is damaged , it should be replaced . LUBRICATION OF FLEXIBLE SHAFT 4 . " Butter " the entire length of the core with a goc Flexible shafts do require ; ) eriodic lubrication grade of general purpose bearing grease witf _ because the core acts as a screw conveyor which minimum operating temperature of - 40 ° F a _ will ; > umpthe lubrication to one end of the shaft over reassemble in casing . DO NOT force ' the grea an extended period of operation . The frequency of into the casing with a grease gun . Too mLJ , lubrication depenes on how the saw is used . When grease wil affect shaft life because it makes t the saw operates continuously for long periods . of core work ha rder . time a lubrication schedule should be developed The time period may be every 80 or 100 hours . Anit indication that the shaft needs lubrication is when becomes noisy . Conversely , when the saw has limited and infreauent use , the grease will GUAR _ _ BEARING POINTS ] 1 _ BEARING POINTS RECOMMENDED ACCESSORIES ITEM CAT . NO . ITEM CAT . IN Steel Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 22214 7 In . Dia . Adjustable Dado Head Caster Sets . . . . . . . . . . . . . . . . . 9 - 22222 or 9 - 22221 9 - 3261 - 9 - 3262 - 9 - 3 , _ Solid Table Extension . . . . . . . . . . . . . . . . . 9 - 29957 7 In , Dia . Dado Head . . . . . . . . . . . . . . . . . . . . . 9 - 31 _ 7 In . Molding Head Set . . . . . . . . . . . . . . . . . . 9 - 3217 Sending Wheel . . . . . . . . . . . . . . . . . . . . . . . 9 - 22 - _ 7 In . Molding Head Set . . . . . . . . . . . . . . . . . . 9 - 3218 Miter - Gauge StOp Rods . . . . . . . . . . . . . . . 9 - 29S 7 In . Molding Head . . . . . . . . . . . . . . . . . . . . . . 9 - 32t4 Miter - Gauge Hold - Down Clamp . . . . . . . 9 - 29 _ Molding / Dado Insert for 7 in . Taper Jig . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 3 : Dia . Molding or Dado Head . . . . . . . . . . 9 - 22271 Universal Jig . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 3 : Work Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 2480 Powe Tool Know How Handbook Sawdust Collection System . . . . . . . . . . . . 9 - 24242 Table Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - _ € 2 " in ' " with 5 / 8 " Bore See Catalog Cast Iron Extension , 12 x 27 Inches . . . . 9 - _ = , v Dia . Sawblades Work Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 2481 Rip Fence Bar . . . . . . . . . . . . . . . . . . . 9 " 2 ° J _ " Table Extension Kit . . . . . . . . . . . . . . . . . . . 9 - 2 _ " 39
Page: 40

TROUBLE SHOOTmNG WARNING : TO AVOID INJURY , TURN SWITCH " OFF " AND ALWAYS REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE TROUBLESHOOTING . TROUBLE SHOOTING - - GENERAL TROUBLE r PROBABLE CAUSE REMEDY Excessive vibraUon . 1 . Blade out of balance . 1 . Discard Blade and use a different blade . , | , . 1 . Miter gauge not adjusted 1 . See " Adjusting Miter Gauge . " Cut when crosscutting • properly . Cut binds , burns or 1 . Dull blade with improper 1 . Sharpen or replace blade . stalls motor when tooth set . 2 . Blade is Heeling . 2 . See " Heeling Adjustment . . . " 3 . Warped board . 3 . Make sure concave or hollow side is facing " down , " feed slowly . 4 . Rip fence not parallel 4 . See " Aligning Rip Fence " " to blade . 5 . Spreader out of 5 . See " Aligning Spreader . " alignment . Cut not true at 90 ° . 1 . Stop screws not properly 1 . See " Blade Tilt " , or " Squareness of Blade or 45 ° positions . I adjusted , to Table . " Tilt and elevating 1 . Sawdust on threads of tilt 1 . See " Maintenance and Lubrication " handwheel turn hard . screw or elevating screw , section . 2 . Bearing retainers 2 , See " Tilt Mechanism . " I i too tight . TROUBLE SHOOTING - - MOTOR NOTE : Motors used on wood - working tools are particularly susceptible to the accumulation of sawdust and wood chips and should be blown out or " vacuumed " frequently to prevent interference with normal motor ventilation . TROUBLE PROBABLE CAUSE REMEDY ' Excessive noise . 1 . Motor . 1 . Have motor checked by qualified service I I technician . Repair service is available at • your nearest Sears store . . . . . . . . | Motor falls to develop i 1 . Circuit overloaded with 1 . Do not use other appliances or motors o , lights , appliances and same circuit when using the saw . LOW VOLTAGE : other motors . length of output . ) 4O
Page: 41

TROUBLE SHOOTING - - MOTOR ( Continued ) TROUBLE PROBABLE CAUSE REMEDY 1 . Low voltage will not Motor starts slowly 1 , Request voltage check from the power or falls to come up trip relay . company . 2 . Windings burned out to full speed . 2 . Have motor repaired or replaced . or open . 3 . Starting relay not 3 . Have relay replaced . operating . 1 . Motor overloaded . 1 . Feed work slower into blade . Motor overheats . 2 . improper cooling . ( Air 2 . Clean out sawdust to provide normal air circulation restricted circulation through motor . See " Maintenance and Lubrication " through motor due to sawdust . section . 1 . Burned switch contacts Starting switch in 1 . Have switch replaced and request a voltage motor will not ( due to extended hold - in check from the power company . periods caused by low operate . line voltage , etc . ) 2 . Have capacitor tested and replace if 2 . Shorted capacitor defective . 3 . Loose or broken 3 . Have wiring checked and repaired . connections . Motor stalls 1 . 1 . Have switch replaced . Starting switch not operating . ( resulting in blown 2 . Voltage too Iowto permit 2 . Request voltage check from the power fuses or tripped circuit breakers ) . motor to reach operating company . speed . 3 . Fuses or circuit breakers 3 . Install proper size fuses or circuit breakers . do not have sufficient capacity . 1 . Motor overloaded . 1 . Feed work slower into blade . Frequent opening of fuses or circuit 2 . Fuses or circuit breakers 2 . Install proper size fuses or circuit breakers . do not have sufficient breakers . capacity . 3 . Starting switch not 3 . Have switch replaced . operating ( motor does reach speed ) 41
Page: 42

REPAIR PARTS \ ! / / ! ! / 42
Page: 43

€ o % . - D . Ol ¢ b , 4 @ w ' = 6 Z . . & IU oo d " O O t - O . ( D m E . o ZE no " Io 00 l - U . IIC 0 0 m , . i I - - < Q . I ' - - _ O 43
Page: 44

E u . I 0 I I I I 44
Page: 45

trl , , - 04 o _ • CO X 0 , , I _ Q O _ C0 x o , ! Q . 6 > 0 ( n T ' - _ 0 e _ 0 d Ec _ ooo _ c E _ c _ LU . _ _ _ . _ _ _ , - - u _ _ - - _ c3 Z . J I . U 0 E 0 : E 0 _ LoDO _ ' _ . C _ _ . _ . - - 0 0 0 . . . . 0 0 _ - ( - g _ OmZI _ 7 _ - J _ _ - _ c _ _ ' cc _ _ , _ _ F - _ < € _ OT u ) ILl . J _ mNaa _ _ NNN E m , O - r - _ < _ o 0 F - o ? . 0 , , , _ m ° P , _ Q w , ' r x m m . J _ rr o z : _ , o _ E m o _ - - 0 I - - € I . h " E < u ) m 0 0 i - ra . . I 4S
Page: 46

PARTS LIST FOR CRAFTSMAN DELUXE 10 INCH TABLE SAW MODEL NO . 113,241691 9 IO 18 17 FIGURE 3 - RIP FENCE ASSEMBLY 62952 Part Key : Pa _ Key No . No . Description No . No . Description 1 62942 Handle 10 62529 Lock , Rear Fence 2 62945 62531 Shoe 11 Roller , Rear Fence 3 62775 Indicator 12 62944 Rod , Fence Lock 4 9404336 13 62533 Screw , Pan Cross Type " T " Spring , Head Alignment • No . 4 - 40 x 1 / 4 ( Includes Key # 18 ) = * Lockwasher , External No . 10 5 62941 Head , Fence 15 " STD611005 * Screw , Hex Head Type " A " I i No . 10x 1 / 2 16 162532 Pad A gnment 17 Cam 18 46
Page: 47

PARTS LaST FOR CRAFTSMAN DELUXE 10 iNCH TABLE SAW MODEL NO . 113.241691 FIGURE 4 - ILLUSTRATION OF MITER GAUGE AND HOLD DOWN Part Key i Part Key No . No . Description No . i No . Description 14 STD551031 * Washer , 21 / 64 x 1 x 1 / 16 , 1 STD601103 * Screw , Pan Head Type " T " 15 37893 10 - 32 x 3 / 8 Gauge , Miter 16 60288 Screw , Locking Set 1 / 4 - 20x3 / 8 2 60425 Bushing * Screw , Pan Cross 8 - 32 x 5 / 16 17 STD510803 3 62779 Latch , Clamp Lock nd cator 18 135 4 62778 Clamp , Lock Block , Indicator 5 62777 Support , Clamp - Pin , Stop 6 STD541231 Nut , Hex 5 / 16 18 Screw , Sems Cross 8 - 32 x 5 / 8 7 62482 Knob Rod , Asm . Miter Gauge 8 37858 Screw , Wing 1 / 4 - 20 x 1 Consisting of Items 23 , 24 , 6 9 9414920 Washer , 17 / 64 x 5 / 8 x ! / 16 Stud , Clamp 10 37841 Clip 24 62383 Stud , Pivot 11 STD600803 25 62780 Screw , Clamp 8 - 32 x 5 / 16 26 9 - 29928 i - Hold Down Assembly 12 37857 Rod , Support 27 : 9 - 29929 itMiter Gauge * Standard Hardware Item - May be purc based locally . - PStock Item - May be secured through the Hardware Departments of most Sears Retail Stores or Catalog Order Houses 47
Page: 48

PARTS LiST FOR CRAFTSMAN DELUXE 10 iNCH TABLE SAW MODEL NO . 113o241591 5 6 ! 3 4 J _ JJ FIGURE 5 - - ON / OFF POWER OUTLET 60381 Key Part No . No . " Description i 60381 eOn / Off Power Outlet Complete 1 60375 Cord Molded 2 60380 . Hous ng , Switch 3 60256 Key , Switch 60374 Switch , Locking 4 • 5 6 x 3 / 4 6 • Does Not Include Key No . 3ed . Order Separately If Requir 48
Page: 49

PARTS LIST FOR CRAFTSMAN DELUXE 10 iNCH TABLE SAW MODEL NO . 113.241691 8 7 10 " l : J FIGURE 6 - - GUARD ASSEMBLY Key Part No . No . Description 62894 Guard , Assembly , Saw 1 60297 Nut , Push Pin 1 / 4 x 1 - I / 2 2 62391 3 62395 Support , Guard 4 62389 Guard , Saw 5 62390 Pin , 1 / 4 x 1 - 3 / 4 * Washer , 17 / 64 x 5 / 8 x 1 / 16 6 STD551025 7 62520 Spacer , Pawl 8 62879 Pawl 9 62861 Spreader , Blade 10 62410 Pin , 1 / 4 x 1 - 3 / 64 11 STD5718t0 * Pin , Roll , 3 / 16 x 15 / 16 12 62519 Spring , Pawi 49
Page: 50

PARTS LiST FOR CRAFTSMAN DELUXE 10 iNCH TABLE SAW MODEL NO , ! 33.241691 FIGURE 7 - - LEGS 3 " Key Pa _ . . . . . I 2 $ 4 No . No . Description , , , , , , . , 1 60314 Screw , Serrated Truss Hd . 1 / 4 - 20 x 5 / 8 2 62552 Leg 3 62554 Stiffener , Side 4 STD551225 " Lockwasher , Ext . 1 / 4 12 5 STD541025 * Nut , Hex 1 / 4 - 20 6 62553 Stiffener , End 7 STD541250 * Nut , Hex 1 / 2 - 13 8 803835 Foot , Leveling HARDWARE FOR ATTACHING LEGS TO SAW . 0 STD523112 * Screw , Hex Hd . 5 / 16 - 18x 1 - 1 / 4 STD551031 Washer , 11 / 32 x 11 / 16 x 1 / 16 11 STD551131 * Lockwasher , Ext . 5 / 16 12 STD541031 * Nut , Hex 5 / 16 - 18 r62752 Bag of Loose Parts For Legs I ( not illust . ) FIGURE 8 - TABLE EXTENSION _ Key Pa _ STD541031 * Nut Hex 5 / 16 - 18 SO
Page: 51

PARTS LIST FOR CRAFTSMAN DELUXE 10 iNCH TABLE SAW MODEL NO , 113.24160 NOTE : ANY ATTEMPT TO REPAIR THIS MOTOR MAY CREATE A HAZARD UNLESS REPAIR IS DONE BY QUALIFIED SERVICE TECHNICIAN . \ Tf5 REPAIR SERVICE IS AVAILABLE \ AT YOUR NEAREST SEARS STORE , FIGURE 9 i 62963 MOTOR Part Key No . No . Description 1 60306 Screw , 8 - 32 x 3 / 8 , Thread Cutting , Slotted , Serrated Hd . 2 64088 Cover , Terminal 3 37588 Capacitor 4 37587 Cover , Capacitor 64142 . Screw , 10 - 32 x 3 / 16 , Thread • Forming , Serrated Hal , 6 64258 Cord with Plug | 51
Page: 52

DELUXE 10 iNCH FLEX DRIVE TABLE SAW SERVICE Now that you have purchased your 10 - inch table saw should a need ever exist for repair parts or service , simply contact any Sears Service Center and most Sears , Roebuck and Co . stores , Be sure to provide all pertinent facts when you cat ] or visit . MODEL NO . The model number of your 10 - inch table saw witt be found at the rear of the base . 113.241691 SAW WITH LEGS TWO CAST IRON TABLE EXTENSIONS MOTOR AND HOLD DOWN CLAMP WHEN ORDERING REPAIR PARTS , ALWAYS GIVE THE FOLLOWING INFORMATION : PART NUMBER PART DESCRIPTION HOW TO ORDER MODEL NUMBER NAME OF ITEM REPAIR PARTS 113.241691 DELUXE 10 - iNCH FLEX DRIVE TABLE SAW All parts listed may be ordered from any Sears Service Center and most Sears stores . If the parts you need are not stocked locally , your order will be electronically transmitted to a Sears Repair Parts Distribution Center for handling . Sold by SEARS , ROEBUCK AND CO . , Chicago , IL . 60684 U . S . A . Part No . 62965 Form No . SP4895 - 4 Printed in U . S . A . 8 / 87
Search in Table Saw on ebay
"