Home | Manufacturer Directory | UPC Lookup | Wanted Manuals | Information Pages |
Register Login | Members Area |

Back To Craftsman Band Saw       Model: 113.247310 or 113247310 Craftsman 12 Inch Band Saw
Regular Text Search or Search by Model Number

Register / log-in to add to your Hammerwall Collection.
Manual Location


Upload a pic of this item

Manuals For Same Model Number.
113.247310 Craftsman 12 in. Band Saw...

Other Model Numbers Referenced to The Same Manual.
113.247210 Craftsman 12 Inch Band Saw...

Other Items that are in the Same Category.
315.214490 Craftsman 9 in. single speed Band Saw Manual...
137.214090 Craftsman 9 in. Band Saw...
351.214610 Craftsman 10 in. Tilting Head Bench Top Band Sa...
137.224120 Craftsman 1 HP 2600 F.P.M. Leg Stand 12 in. Ban...
113.247410 Craftsman 12 in. Electronic Band Saw...
113.247210 Craftsman 12 in. Band Saw...
113.247310 Craftsman 12 in. Band Saw...
113.247110 Craftsman 10 in. Band Saw...
351.214600 Craftsman 10 in. Tilting Head Bench Top Band Sa...
315.214770 Craftsman 9 in. Band Saw...

This is a partial text extraction from the pdf, to download the pdf, click the Manual tab. If you want to search this text, hold control and F, and type the word you are looking for.

Page: 1

Save ThisManual ForFuture Reference A / RS owners manual MODEL NO . 113.2472t0 BAND SAW WITH LEG SET MODEL NO . 113.247310 1t3.2473t0 113.24 7210 BAND SAW WITH CABINET S _ rial Number _ _ Model and serial numbers CRRFTSMRN may be found at the left - hand side of the base . You should record both model and serial number in a safe place for future USe . im N 12 - 1NCH BAND SAW CAUTION : • assembly READALL INSTRUCTIONS • operating CAREFULLY • repair parts _ , . j . . . . . _ , ' Sold by SEARS , ROEBUCKAND CO . , Chicago , IL 60684 U . S . A . Part No . SP5086 Printed in U . S . A
Page: 2

FULL ONE YEAR WARRANTY ON CRAFTSMAN BAND SAW If within one year from lhe date of purchase , this Craftsman Band Saw fails due to a defect in malarial or workmanship , Sears will repair it , free of charge . WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SERVICE CENTER / DEPARTMENT THROUGHOUT THE UNITED STATES . This warranty applies only while this product is used in the United States . This warranty gives you specific legal rights and you may also have other rights which vary from state to state . SEARS , ROEBUCK AND CO . , DEPT . 698 / 731A Sears Tower , Chicago , IL 60684 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS Z87 . 1 ) at all times . Everyday eyeglasses only 1 . KNOW YOUR POWER TOOL have impact resistant lenses , they are NOT Read and understand the owner's manual and safety glasses . Also . use face or dust mask if labels affixed to the tool . Learn its application cutting operation is dusty , and ear protectors and limitations as well as the specific potential ( plugs or muffs ) during extended periods of hazards peculiar to this too ! . operation . 2 . GROUND ALL TOOLS 13 . SECURE WORK This tool is equipped with an tapprovedype Use clamps or a vise to hold work when practical . 3 - conductor cord and a 3 - prong grounding It's safer than using your hand , and frees both plug to fit the proper grounding type receptacle . hands to operate tool . The green conductor in the cord is the groundinglive wire . Never connect the green wire to a 14 . DON'T OVERREACH terminal . Keep proper footing and balance at all times . 3 . KEEP GUARDS IN PLACE , 15 . MAINTAIN TOOLS WITH CARE in working order , and in proper adjustment and Keep _ ools sharp and clean for best and safest alignment . performances . Follow instructions for lubricating 4 . REMOVE ADJUSTING KEYS AND WRENCHES an d changing accessories . Form habit of checking to see that keys and 16 . DISCONNECT TOOLS adjusting wrenches are removed from tool before before servicing ; when changing accessories turning it on . such as blades , bits , cutters , etc . 5 . KEEP WORK AREA CLEAN 17 , AVOID ACCIDENTAL STARTING Cluttered areas and benches invite accidents . Make sure switch is in " OFF " position before Floor must not be slippery due to wax orsawdust . plugging in . 6 . AVOID DANGEROUS ENVIRONMENT 18 . USE RECOMMENDED ACCESSORIES Don't use power tools in damp orwet locations or Consult the owner's manual for recommended expose them to rain . Keep work area well lighted . acce _ . ories . Follow the instructions that accom - Provide adequate su rrou nding work space . palty the accessories . The use of improper acces - 7 . KEEP CHILDREN AWAY sories - may cause hazards . All visitors should be kept a safe distance from 19 . NEVER STAND ON TOOL work area . Serious inlu ry could occur if the tool is tipped or 8 . MAKE WORKSHOP CHILD - PROOF if the cutting tool is accidentally contacted . Doch not store materials above or near the tool su - - with padlocks , master switches , orby removing that it is necessary to stand on the tool to reach starter keys . them . 9 . DON'T FORCE TOOL 20 . CHECK DAMAGED PARTS It will do the job better and safer at the rate for Before further use of the tool , a guard or other which it was designed . part that is damaged should be carefully checked 10 . USE RIGHT TOOL to ensure that it will operate properly and perform Don't force tool or attachment to do a job it was its intended function . Check for alignment of not designed for . moving parts , binding of moving parts , breakage 11 . WEAR PROPER APPAREL of parts , mounting , and any other conditions that Do not wear loose clothing , gloves , neckties or may effect its operation . A guard or other part jewelry ( rings , wrist watches ) to get caught in that is damaged should be properly repaired or moving parts . Nonslip footwear is recommended . replaced . Wear protective hair covering to contain long 21 . NEVER LEAVE TOOL RUNNING UNATTENDED hair . Roll long sleeves above the elbow . Turn power off . Don't leave tool until it comes to 12 . USE SAFETY GOGGLES ( Head Protection ) a complete stop . Wear Safety goggles ( must comply with ANSI
Page: 3

additional safety instructions for band saw Safety is a combination of common sense , staying and lock knob , lower blade guide , tension adjust - alert , and knowing how your band saw works . ing knob and tension scale , and blade thrust bearing adjustment . BEFORE USING THE SAW : 3 . Read and understand all safety instructions and operating procedures throughout the manual . WARNING : TO AVOID MISTAKES THAT COULD 4 . Read the following labels which appear on the RESULT IN SERIOUS , PERMANENT INJURY , DO top of the band saw and blade guard . NOT PLUG THE SAW IN UNTIL THE FOLLOWING STEPS HAVE BEEN SATISFACTORILY COMPLETED : , ALLOW j 1 . Assembly and alignment . I " roo _ To I I ITOP 2 . Learn the function and proper use of the on - off switch , bevel crank and lock , upper blade guide 1 AAB _ EDFBOERjuEFS _ TO _ tNG I DANGER I FOR YOUR OWN SAFETY : Know This Tool ! Read and Understand Owner's Manual befo _ UsirKj this Machine . | • Always wear safety gOggleS that comply • Before turning saw on , adjust UPPER = Pl _ hind positions so I sudden • tip " Turn Paw off , re . love switch key , _ r . d wait with ANSI Z87 , 1 . BLADE GUIDE to just clear worhplece , won't cause injury , le ; - blade to stop before adjusting saw , = Before turning _ , w on , check and adjust : • Support , fixture or brace workplece • Turn saw off and walt for bta _ e to slop changing bleOes or leaving ires . a ) Blade Tension b ) Blade Guides firmly against table so it will not rock before freeing jamme _ material . • Maintain _ / ls " maximum clearance Between J c ) Thrust Bearings or twist from your hand . table and sanding belt . WEAR YOUR WHEN INSTALLING OR MOVING THE SAW available at Sears retail or catalog stores . Use 1 . To avoid injury from unexpected saw movement : of glasses or use of goggles not in compliance a . Place the saw on a firm level surface where with ANSI Z87 . 1 could result in severe injury there is plenty of room for feeding the work - from breakage of the eye protection . piece . C . For dusty operations , wear a face shield along b . Adjust the saw so the table is level and the saw with safety goggles . does not rock . d . Use extra caution with large , very small , or c . Bolt the saw to the floor if it tends to slip , slide , awkward workpieces . or tip over during operations like cutting long , 1 . Use extra supports ( tables , saw horses , heavy boards . etc . ) for any workpieces large enough to tip d . Turn saw off and unplug electric cord before when not held down to the table top . moving the saw to a new area . 2 . Do not feed small pieces that require your 2 . Store and use the band saw indoors . finger holding the workpiece to go under the guard area . Use jigs or fixtures to hold BEFORE EACH USE the work and keep your hands away from 1 . Inspect your saw . If any part of this band saw is the blade . missing , or bent , or failed in any way , or any . When cutting irregularly shaped work - electrical components do not work properly , turn pieces , plan your work so it will not pinch the saw off , remove switch key , and unplug the the blade . A piece of molding , for example , saw . Replace damaged , missing , or failed parts must lay flat or be held by a fixture or jig that before using the saw again . will not let it twist , rock or slip while being 2 . Plan your work to protect youreyes , hands , face , cut . ears and body . 4 . Properly support round material such as a . Do not do layout , assembly , or set up work on dowel rods , or tubing . They have a tendency the table while the saw is running . to roll while being cut , causing the blade to " bite . " To avoid this , always use a " V " block , b . Wear safety goggles ( not glasses ) that comply or clamp the workpiece to a miter gage . with ANSI Z87 . 1 ( shown on package ) . Using any power tool can result in foreign objects e . To avoid risk of hearing damage , wear ear being thrown into the eyes , which can result in plugs or muffs during extended periods of permanent eye damage . Safety goggles are operation .
Page: 4

a . If your saw makes an unfamiliar noise or if it Toavoidbeingsuddentlycaughtintheblade : vibrates excessively , stop immediately . Turn 1 . Donotweargloves . the saw off . Remove switch key and unplug 2 . Removeall jewelryandlooseclothing . the saw . Do not restart until finding and correcting the problem . 3 . Tiebacklonghair . b . Avoid awkward hand positions where a sudden 4 . Rolllongsleevesabovetheelbow . slip could cause a hand to move into the blade or the sanding belt . To avoid injury from accidental starting , always g _ unplug saw , turn switch off and remove switch c . Feed the workpiece only fast enough to let the key before removing the guard , installing or blade cut without bogging down or binding . removing any blade , accessory or attachment , d . Before freeing jammed material , turn saw off . or making any adjustments . Remove switch key . Remove plug from power h . To avoid slips and jams causing injury : sou rce outlet . Wait for all moving parts to stop . 1 . Choose the right size and style blade for the e . When backing up the workpiece , the blade material and the type of cutting you plan to may bind in the kerf ( cut ) . This is usually do . Use this band saw to cut and sand only caused by sawdust clogging up the kerf or wood , wood like products and plastic . because the blade comes out of the guides _ If this happens : 2 . Make sure the blade teeth point downward toward the table . 1 . Turn saw off . 3 . Make sure the blade tracking guides and 2 . Unplug saw . thrust bearings are properly adjusted . 3 . Remove switch key . 4 . Always check and correctly adjust blade or 4 . Wait for all moving parts to stop . sanding belt tension . 5 . Remove band saw cover . To avoid accidental blade contact , minimize 6 . Stick a flat blade screwdriver or wedge into blade breakage and provide maximum blade the kerf . support . 7 . Turn the upper wheel by hand while backing 1 . Always adjust the upper blade guide and up the workpiece . blade guard to just clear the workpiece . Before removing loose pieces from the table , 2 . Plan your hand placement so your fingers turn saw off and wait for all moving parts to will not be where a sudden slip could cause them to hit the blade . stop . Make sure all clamps and locks are tight and ACCESSORIES j . there is no excessive play in any parts . To avoid injury from untested or improper acces - k . To avoid an electrical shock , make sure your sories , use only Recommended Accessories list - fingers do not touch the metal prongs on the ed on the Accessory page of this manual . plug when installing or removing the plug to or from a live outlet . Never turn your band saw " ON " before clearing everything except the workpiece and related feed or support devices off the table . BEFORE SANDING 1 . Keep the table and sanding belt adjusted so the gap between them is no more than 1 / 16 - inch wide . 2 . To avoid fire , shock , or cause electrical shorts , do not sand metal . It could ignite the sawdust inside the saw . WHENEVER SAW IS RUNNING WARNING : DO NOT ALLOW FAMILIARITY ( GAINED FROM FREQUENT USE OF YOUR BAND SAW ) TO CAUSE A CARELESS MIS - TAKE . ALWAYS REMEMBER THAT A CARE - LESS FRACTION OF A SECOND IS SUFFI - CIENT TO INFLICT SEVERE INJURY . 4
Page: 5

table of contents Page Page Attaching Trim Caps and Trim Ledge . . . . . . . . 17 General Safety Instructions for Power Tools . . . . 2 Additional Safety Instructions for Band Saw . . . . 3 Attaching Handwheel . . . . . . . . . . . . . . . . . . . . . . 17 Location and Function of Controls . . . . . . . . . . . . 18 Before Using the Saw . . . . . . . . . . . . . . . . . . . . . . . 3 When Installing or Moving the Saw . . . . . . . . . . . 3 Getting to Know Your Band Saw . . . . . . . . . . . . 18 Before Each Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installing the Blade . . . . . . . . . . . . . . . . . . . . . . . . . 19 Before Sanding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Aligning the Blade and Blade Guide . . . . . . . . . 20 Glossary of Terms for Woodworking . . . . . . . . . . : 5 Mounting the Front Table . . . . . . . . . . . . . . . . . . . 22 Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . 6 Squaring the Blade to the Table . . . . . . . . . . . . . 22 On - Off Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Motor Safety Protection . . . . . . . . . . . . . . . . . . . . . 6 Tilting Head for Bevel Cut . . . . . . . . . . . . . . . . . . 25 Wire Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Adjusting Bevel Lock Knob . . . . . . . . . . . . . . . . . 25 Unpacking and Checking Contents . . . . . . . . . . . . . 7 Basic Band Saw Operation . . . . . . . . . . . . . . . . . . . 26 Tools Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Circle Cutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Sawdust Collection . . . . . . . . . . . . . . . . . . . . . . . . 27 Table of Loose Parts . . . . . . . . . . . . . . . . . . . . . . . . 8 Assembly and Alignment . . . . . . . . . . . . . . . . . . . . . 10 Installing Sanding Attachment . . . . . . . . . . . . . . 27 Installing the Sanding Belt . . . . . . . . . . . . . . . . . . 28 Assembling Leg Set ( Model 113.247210 ) . . . . . 10 Recommended Accessories . . . . . . . . . . . . . . . . . . . 28 Assembling Cabinet ( Model 113.247310 ) . . . . . 11 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Mounting the Motor . . . . . . . . . . . . . . . . . . . . . . . . 13 Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Connecting the Motor . . . . . . . . . . . . . . . . . . . . . . 15 Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Mounting the Saw to the Cabinet . . . . . . . . . . . . 16 Mounting the Saw to the Leg Set . . . . . . . . . . . . 16 glossary of terms for woodworking Push Stick Beveling A device used to feed the workpiece through the saw An angle cutting operation through the face of the board . during narrow ripping type operations so the opera - tor's hands are kept well away from the blade . Crosscut Resaw A cutting operation made across the width of the A cutting operation to reduce the thickness of the workpiece . workpiece to make thinner pieces . Compound Cutting Resin A simultaneous bevel and miter cutting operation . A sticky , sap based substance that has dried . FPM Ripping Feet per minute . Used in reference to surface speed of blade . A cutting operation along the length of the work - piece . Freehand ( as used for band saw ) Sawblade Path Performing a cut without the workpiece properly The area of the worktable or workpiece directly in supported on the work table . line with the saw blade . Gum Set A sticky , sap based residue from wood products . The distance the tip of the saw blade tooth is bent Kerf outward from the face of the blade . The material removed by the blade in a through cut Trailing End orthe slot produced by the blade in a non - through or The workpiece end last cut by the saw blade . partial cut . Leading End Workpiece The end of the workpiece which is pushed into the The item on which the cutting operation is being cutting tool first , performed . The surfaces of a workpiece or commonly referred to as faces , ends , and edges . Mitering Worktable An angle cutting operation made across the width of The surface on which the workpiece rests while the workpiece . performing a cutting or sanding operation .
Page: 6

electrical connections POWER SUPPLY WARNING : TO MAINTAIN PROPER TOOL GROUND - ING WHENEVER THE OUTLET YOU ARE PLAN - Motor Specifications NING TO USE FOR THIS POWER TOOL IS OF THE The A - C motor used in this saw is a capacitor - start , TWO PRONG TYPE , DO NOT REMOVE OR ALTER non - reversible type having the following specifica - THE GROUNDING PRONG IN ANY MANNER . USE tions : AN ADAPTER AS SHOWN AND ALWAYS CON - NECT THE GROUNDING PRONG TO KNOWN MODEL NO . MODEL NO . GROUND . 113.247210 113.247310 Rated H . P . . . . . . . . . . . . . . . 1 / 2 5 / 8 It is recommended that you have a qualified electri - Maximum cian replace the two prong outlet with a properly Developed H . P . 1 1 - 1 / 8 grounded three prong outlet . Voltage . . . . . . . . . . . . . . . . 120 120 An adapter as shown is available for connecting the Amperes . . . . . . . . . . . . . . . 8.0 8.8 plug to 2 - prong receptacles . The green grounding Hertz ( Cycles ) . . . . . . . . . . 60 60 lead extending from the adapter must be connected Phase . . . . . . . . . . . . . . . . . . Single Single toa permanent ground such as a properly grounded RPM . . . . . . . . . . . . . . . . . . . 3450 3450 outlet box . Rotation of Shaft . . . . . . . . Clockwise Clockwise GROUNDING LUG WARNING : TO AVOID ELECTRICAL HAZARDS , FIRE HAZARDS , OR DAMAGE TO THE TOOL , USE ADAPTER _ - _ : _ PROPER CIRCUIT PROTECTION . YOUR SAW IS WIRED AT THE FACTORY FOR 120V OPERATION . \ J l _ ll MAKE SURE THIS IS 3 - PRONG \ _ L _ - _ _ CONNECTED TO A CONNECT TO A 120V , 15 - AMP , BRANCH CIRCUIT PLUG \ _ - I , ' _ l { KNOWN GROUND AND USE A 15 - AMP FUSE OR CIRCUIT BREAKER . TO AVOID SHOCK OR FIRE , IF POWER CORD IS WORN OR CUT , OR DAMAGED IN ANY WAY , HAVE IT REPLACED IMMEDIATELY . IF NOT PROPERLY GROUNDED THIS POWER WARNING : THE ADAPTER ILLUSTRATED IS FOR TOOL CAN CAUSE ELECTRICAL SHOCK - - USE ONLY IF YOU ALREADY HAVE A PROPERLY PARTICULARLY WHEN USED IN DAMP LOCA - GROUNDED 2 - PRONG RECEPTACLE . TIONS CLOSE TO PLUMBING . IFAN ELECTRICAL SHOCK OCCURS THERE IS ALSO THE POTEN - MOTOR SAFETY PROTECTION TIAL OF A SECONDARY HAZARD SUCH AS YOUR HANDS CONTACTING THE SAWBLADE . NOT ALL CAUTION : To avoid motor damage this motor should OUTLETS ARE PROPERLY GROUNDED . IF YOU be blown out or vacuumed frequently to keep ARE NOT SURE THAT YOUR OUTLET IS PRO - sawdust from interfering with normal motor ventila - tion . PERLY GROUNDED , HAVE IT CHECKED BY A QUALIFIED ELECTRICIAN . 1 . This tool should be connected to a 120V , 15 amp branch circuit with a 15 amp fuse or circuit Your unit has a plug that looks like the one shown below . breaker . Failure to use the proper size fuse can 3 - PRONG PLUG result in damage to the motor . 2 . If the motor fails to start , turn the power switch to PROPERLY the " OFF " position immediately . UNPLUG THE GROUNDED TOOL . Check the saw blade to make sure it turns OUTLET freely . If the blade is free , try to start the motor 0 again . If the motor still does not start , refer to the GROUNDING PRONG " Motor Trouble - Shooting Chart . " 3 . If the motor suddenly stalls while cutting wood , turn the power switch off , unplug the too ! , and free the blade from the wood The motor may now be restarted and the cut finished . . Frequent " blowing " of fuses or tripping or circuit This power tool is equipped with a 3 - conductor cord breakers may result if : and ground type plug listed by Underwriters ' Labora - a . MOTOR IS OVERLOADED - Overloading can tories . The ground conductor has a green jacket and occur if you feed too rapidly . is attached to the tool housing at one end and to the ground prong in the attachment plug at the other end . This plug requires a mating 3 - conductor grounded type outlet as shown above .
Page: 7

b . LOWVOLTAGE - Althoughthemotoris de - overheating and motor burn - out , use the table below signedfor operationon the voltage and fre - to determine the minimum wire size ( A . W . G ) exten - quency specified on the motor nameplate , sion cord , Use only 3 - wire extension cords which normal loads will be handled safely on voltages have 3 - prong grounding type plugs and 3 - pole not more than 10 % above or below the name - receptacles which accepts the tools plug . plate voltage . Heavy loads , however , require CAUTION : For circuits that are farther away from that voltage at motor terminals equals the electrical service box , the wire size must be increased voltage specified on nameplate . proportionately in order to deliver ample voltage to the saw motor . 5 . Most motor troubles may be traced to loose or incorrect connections , overload , reduced input voltage ( such as small size wire in the supply | Length of the _ 120 Volts Wire Sizes Required circuit ) or to overly long supply circuit wire . Always check the connections , the load and the Conductor 1 ( American Wire Gage Number ) supply circuit whenever motor fails to perform 0 - 25 Ft . I 14 satisfactorily . Check wire size and length with 26 - 50 Ft . 12 the Wire Size Chart below . 51 - 100 Ft . _ 8 WIRE SIZES The use of any extension cord wil ! cause some loss of power . To keep this to a minimum and to prevent unpacking and checking contents TOOLS NEEDED COMBINATION SQUARE MUST BE TRUE STRAIGHT EDGE OF BOARD 3 / 4 - 1NCH THICK THIS EDGE MUST BE PEFCTLY STRAIGHT MEDIUM SCREWDRIVER I I 1 # 2 PHILLIPS SCREWDRIVER II I 3iB " WRENCH : : : : : : : : : : : : : : : : : : : : : : : - , DRAW LIGHT I T / 16 " WRENCH LINE ON BOARD COMBINATION 9 / 16 " WRENCH ALONG THIS EDGE _ _ SQUARE L _ 7 / 16 " ESOCKETT 3 / 8 " SOCK _ _ 9 / 16 " SOCKET 1 / 8 " HEX " L " WRENCH / 5 / 32 " HEX " L " WRENCH _ SOCKET WRENCH SHOULD BE NO GAP OR OVERLAP HERE WHEN SQUARE IS FLIPPED OVER IN DOTTED POSITION WARNING : TO AVOID INJURY FROM UNEXPECT - WARNING : IF ANY PARTS ARE MISSING , DO ED SfARTING OR ELECTRICAL SHOCK , DO NOT NOT ATTEMPT TO ASSEMBLE THE BAND PLUG THE SAW IN UNTIL ALL ASSEMBLY AND SAW , PLUG IN THE POWER CORD , OR TURN ALIGNMENT STEPS ARE COMPLETE . THE POWER THE SWITCH ON UNTIL THE MISSING PARTS CORD MUST REMAIN UNPLUGGED WHENEVER ARE OBTAINED AND ARE INSTALLED COR - YOU ARE WORKING ON THE SAW . RECTLY . Unpacking and Checking Contents , Remove front table and front cover first while saw is being unpacked . To remove the front 1 . Separate all " loose parts " from packaging mater - cover , pull the cover at the neck and underside of ials and check each item with " Table of Loose th roat area . Parts " to make sure all items are accounted for , before discarding any packing material .
Page: 8

unpacking and checking contents TABLE OF LOOSE PARTS Model 113.247310 Band Saw comes complete Model 113.247210 Band Saw comescomplete in one carton and includes a cabinet with a lower in one carton and includes steel legs . shelf , ITEM DESCRIPTION QTY . AA Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ITEM DESCRIPTION QTY . AA Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 BB Basic Saw Assembly . . . . . . . . . . . . . . . . . . . 1 CC Owners Manual . . . . . . . . . . . . . . . . . . . . . . . 1 BB Basic Saw Assembly . . . . . . . . . . . . . . . . . . . 1 CC Owners Manual . . . . . . . . . . . . . . . . . . . . . . . 1 DD Leg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 GG Cabinet Assembly . . . . . . . . . . . . . . . . . . . . . 1 EE Stiffener , Upper . . . . . . . . . . . . . . . . . . . . . . . 4 HH Trim Cap , L . H . . . . . . . . . . . . . . . . . . . . . . . . . 1 FF Stiffener , Lower . . . . . . . . . . . . . . . . . . . . . . . 4 II Trim Ledge . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 HH Trim Cap , L . H . . . . . . . . . . . . . . . . . . . . . . . . . 1 JJ Trim Cap , R . H . . . . . . . . . . . . . . . . . . . . . . . . . 1 II Trim Ledge . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 LL Loose Parts Bag JJ Trim Cap , R . H . . . . . . . . . . . . . . . . . . . . . . . . . 1 containing the following items . KK Loose Parts Bag Band Saw Blade . . . . . . . . . . . . . . . . . . . . . . . 1 containing the following items . Handwheel Assembly . . . . . . . . . . . . . . . . . . 1 Sanding Belt 1 / 2 × 80 . . . . . . . . . . . . . . . . . . 1 Handwheel Asssernbly . . . . . . . . . . . . . . . . . 1 Sanding Belt 1 / 2 x 80 . . . . . . . . . . . . . . . . . . 1 Band Saw Blade . . . . . . . . . . . . . . . . . . . . . . . 1 Bag of Loose Parts # 507655 . . . . . . . . . . . . 1 Bag of Loose Parts # 507655 . . . . . . . . . . . . 1 Bag of Loose Parts # 507666 . . . . . . . . . . . . 1 Bag of Loose Parts # 507657 . . . . . . . . . . . . 1 Bag of Loose Parts # 507755 . . . . . . . . . . . . 1 Bag of Loose Parts # 507666 . . . . . . . . . . . . 1 NOTE : To avoid damage to the band saw leave it laying on its left side until you are ready to mount it to the leg set or cabinet . To prevent scratching the finish , lay a piece of the packing box under the saw . BB CC KKiLL FF DD EE GG
Page: 9

° © c © LIST OF LOOSE PARTS IN BAG # 507657 MODEL 113.247210 ITEM DESCRIPTION QTY . A Truss Head Screw 1 / 4 - 20 x 1 / 2 . . . . . . . . . 44 B Lockwasher Ext . 1 / 4 . . . . . . . . . . . . . . . . . . . 44 E @ C Hex Nut 1 / 4 - 20 . . . . . . . . . . . . . . . . . . . . . . . . 44 D Leveling Foot . . . . . . . . . . . . . . . . . . . . . . . . 4 E Hex Jam Nut 3 / 8 - 16 . . . . . . . . . . . . . . . . . . . 8 ( ] ] _ \ _ \ \ _ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ _ LIST OF LOOSE PARTS IN BAG # 507655 o @ MODEL 113.247210 & 113.247310 ITEM DESCRIPTION QTY . H * F Pan Hd . Screw t0 - 32 x 2 . . . . . . . . . . . . . . . 1 G Hex Nut 10 - 32 . . . . . . . . . . . . . . . . . . . . . . . . . 1 H Switch Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 I Lo Hd Screw Cap 1 / 4 - 20 x 5 / 8 . . . . . . . . . 2 J Spacer # 10 x 5 / 16 . . . . . . . . . . . . . . . . . . . . . 3 K Hex Flange Lock Nut 10 - 32 . . . . . . . . . . . . 4 J K L L Locking Set Screw 1 / 4 - 20 x 1 / 2 . . . . . . . . . 3 R M Wingnut 5 / 16 - 18 . . . . . . . . . . . . . . . . . . . . . . . 12 N Pan Hd . Screw 1 / 4 - 20 x 5 / 8 . . . . . . . . . . . . B Lockwasher Ext . 1 / 4 . . . . . . . . . . . . . . . . . . . 2 C Hex Nut 1 / 4 - 20 . . . . . . . . . . . . . . . . . . . . . . . . 2 O Hex Hd . Screw Ty TT 1 / 4 - 20 x 5 / 8 . . . . . . 4 P Pan Hd . Screw Ty BT 1 / 4 x 1 / 2 . . . . . . . . . 6 N 0 P Q * LIST OF LOOSE PARTS IN BAG # 507755 J MODEL 113.247310 ITEM DESCRIPTION QTY . A Truss Head Screw 1 / 4 - 20 x 1 / 2 . . . . . . . . . 30 B Lockwasher Ext . 1 / 4 . . . . . . . . . . . . . . . . . . . 30 C Hex Nut 1 / 4 - 20 . . . . . . . . . . . . . . . . . . . . . . . . 30 D Levelin ¢ l Foot . . . . . . . . . . . . . . . . . . . . . . . . . 4 S . k E Hex Jam Nut 3 / 8 - 16 . . . . . . . . . . . . . . . . . . . 8 Q Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 LIST OF LOOSE PARTS IN BAG # 507666 U MODEL 113.247210 & 113.247310 ITEM DESCRIPTION QTY . R Sanding Platen . . . . . . . . . . . . . . . . . . . . . . . . 1 V _ S Table Alignment Key . . . . . . . . . . . . . . . . . . 1 T Table Latch . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 U Belt Tension Stud . . . . . . . . . . . . . . . . . . . . . 1 V Poly " V " Belt . . . . . . . . . . . . . . . . . . . . . . . . . . 1 W Poly " V " Pulley . . . . . . . . . . . . . . . . . . . . . . . . t X Table Latch Spring . . . . . . . . . . . . . . . . . . . . 2 Y Table Alignment Spring . . . . . . . . . . . . . . . . 2 W _ * NOT SHOWN TO SCALE 9
Page: 10

assembly and alignment ASSEMBLING LEG SET Model 113.247210 From the loose parts bag find the following hard - . ware : ITEM DESCRIPTION QTY . A Truss Head Bolts 1 / 4 - 20 x 1 / 2 . . . . . . . . . . 40 B Lock Washers Ext . 1 / 4 . . . . . . . . . . . . . . . . . 40 \ C Hex Nuts 1 / 4 - 20 . . . . . . . . . . . . . . . . . . . . . . . 40 D Leveling Feet . . . . . . . . . . . . . . . . . . . . . . . . . . 4 E Hex Nut 3 / 8 - 16 . . . . . . . . . . . . . . . . . . . . . . . . 8 From the loose parts find the following items : ITEM DESCRIPTION QTY . DE ) Legs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 EE Upper stiffeners . . . . . . . . . . . . . . . . . . . . . . . 4 FF Lower stiffeners . . . . . . . . . . . . . . . . . . . . . . . 4 Assemble the Leg Set as follows : 1 . Attach the four ( 4 ) legs to the four ( 4 ) upper stiffeners as shown . Three ( 3 ) bolts , washers , and nuts are required to fasten each end of upper stiffener to a leg . Hand tighten hex nuts . 2 . Attach the four ( 4 ) lower stiffeners to the legs . Two ( 2 ) bolts , washers and nuts are required to hold each end of a lower stiffener in place . Hand tighten hex nuts . 3 . Attach four ( 4 ) leveling feet to bottom of each leg as illustrated . Hand tighten hex nuts . 4 . Put leg set in area intended for use of saw . With a 7 / 16 - inch wrench or socket , securely tighten all bolts . Adjust leveling feet . WARNING : TO AVOID INJURY FROM UNEXPECT - ED SAW OR WORK MOVEMENT , LEVELING FEET MUST BE ADJUSTED SO THAT SAW DOES NOT ROCK . To Adjust leveling feet so the saw will sit properly : LEG a . Move saw to desired location . b . With 9 / 16 - inch wrench loosen bottom nut . . IEX NUTS c . Back off top nut by hand . d . Raise or lower foot by adjusting bottom nut using 9 / 16 - inch wrench . LEVELING FOOT e . Snug top nut against inside of leg by hand . f . Adjust all four feet as necessary then tighten all four bottom nuts using a 9 / 16 - inch wrench . 10
Page: 11

ASSEMBLING CABINET Model 113.247310 1 . Separate all " loose " parts from packing materialske and check each item with " Parts List " to ma sure all items are accounted for before discard - 4 ing any packing material . From loose parts find the following items : ITEM DESCRIPTION QTY . 1 Right Side Panel . . . . . . . . . . . . . . . . . . . . . . 1 2 Left Side Panel . . . . . . . . . . . . . . . . . . . . . . . . 1 4 3 Lower Shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 4 Skirt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 l 5 Shelf Stiffener . . . . . . . . . . . . . . . . . . . . . . . . . 1 6 Corner Bracket . . . . . . . . . . . . . . . . . . . . . . . . 2 7 Spacer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 From loose parts bag find the following hardware : ITEM DESCRIPTION QTY . A Screw , Truss Head 1 / 4 - 20 x 1 / 2 . . . . . . . . . 34 B Lockwasher Ext . 1 / 4 . . . . . . . . . . . . . . . . . . . 34 6 7 6 C Nut , Hex 1 / 4 - 20 . . . . . . . . . . . . . . . . . . . . . . . 34 D Foot Leveling . . . . . . . . . . . . . . . . . . . . . . . . . 48 E Hex Nut 3 / 8 - 16 . . . . . . . . . . . . . . . . . . . . . . . . R Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 o o o o LOWER 2 . After layout of cabinet parts , take the lower shelf SHELF and turn upside down on floor . Small front flange should be pointing upward . CORNER 3 . Locate the two ( 2 ) corner brackets , four ( 4 ) 1 / 4 - BRACKETS 20 x 1 / 2 truss head bolts , Iockwashers , and nuts . - . . . . Attach the corner brackets to the front flange in holes as illustrated . Attach both corner brackets . 44 CORNERBRACKETS SHELF 4 . Locate the two ( 2 ) side panels , one ( 1 ) shelf stiffener , and six ( 6 ) 1 / 4 - 20 x 1 / 2 truss head bolts , Iockwashers and hex nuts . Place the right side panel on its back side as illustrated . Stand up the lower shelf on the rear flange and line up the holes on the corner bracket and shelf stiffener with the holes in the side panel . Mount the bolts in the three holes and tighten hex nuts with a 7 / 16 - inch wrench or socket . Repeat procedure RIGHT SIDE SHELF STIFFENER PANEL for left side panel . REAR FLANGE 1 !
Page: 12

assembly and alignment EAS . KI . T RIGHT SIDE PANEL 5 . Locate the two ( 2 ) skirts , eight ( 8 ) 1 / 4 - 20 x 1 / 2 truss head bolts , Iockwashers and hex nuts . Assemble the one ( 1 ) skirt to the front of the \ cabinet through the holes as illustrated . \ Stand the cabinet upright and assemble the rear \ skirt . Hand tighten nut only at this time . NOTE : After the saw is mounted to the cabinet , all the hex nuts should be tightened . This will allow easy alignment of the mounting holes . FRONT SKIRT SHELF LEFT SIDE PANEL 6 . Secure rear of shelf to right side and left side panels using two ( 2 ) 1 / 4 - 20 x 1 / 2 truss head bolts , Iockwashers , and hex nuts . Hand tighten nuts only at this time . 7 . Locate the right and left side spacers , the six ( 6 ) 1 / 4 - 20 x 1 / 2 truss head bolts , Iockwashers , and hex nuts . Position the spacer inside the right and left side panels and fasten in the three holes as illustrated . Tighten nuts using a 7 / 16 - inch wrench SPACER or socket . 8 . Locate the two ( 2 ) covers and attach to openings in the right and left side panels as illustrated . RIGHT SIDE PANEL COVER 9 . Locate four ( 4 ) leveling feet and eight ( 8 ) 3 / 8 - 16 hex nuts . Attach the leveling feet to bottom of side panels in front and rear as illustrated . Hand tighten hex nuts . WARNING : TO AVOID INJURY FROM UN - EXPECTED SAW OR WORK MOVEMENT , LEVELING FEET MUST BE ADJUSTEO SO THAT SAW DOES NOT ROCK . 10 . To adjust leveling feet so the saw will sit properly : a . Move saw to desired location . b . With 9 / 16 - inch wrench loosen bottom nut . c . Back off top nut by hand . d . Raise or lower foot by adjusting bottom nut using 9 / 16 - inch wrench . e . Snug top nut against inside of leg by hand . f . Adjust all four feet as necessary then tighten all four bottom nuts using a 9 / 16 - inch wrench . 12
Page: 13

assembly and alignment MOUNTING THE MOTOR 1 . Find the following parts : J K ) ITEM DESCRIPTION QTY . AA Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 J Spacer ( 1 / 40 . D . x 5 / 16 ) . . . . . . . . . . . . . . . 3 K Flanged Locknut # 10 - 32 . . . . . . . . . . . . . . . 4 M Wing Nut 5 / 16 - 18 . . . . . . . . . . . . . . . . . . . . . . 11 U Belt Tension Stud . . . . . . . . . . . . . . . . . . . . . W Motor Pulley w / Set Screw . . . . . . . . . . . . . . 1 V Poly " V " Belt . . . . . . . . . . . . . . . . . . . . . . . . . . 1 W _ * NOT SHOWN TO SCALE 2 , Have the band saw positioned on its left side as unpacked , To prevent scratching the finish , lay a piece of the packing box under the saw . 3 . Place the three ( 3 ) spacers onto the three motor studs as shown . Pay attention to where the oil plug is located . No spacer goes on the fourth motor stud . OIL PLUG PULLEY 4 . Install the motor pulley onto the motor shaft with the set screw boss toward the motor . Position the outer face of the pulley 2 - 1 / 4 inches from the end shield of the motor and tighten the set screw 2 - 1 / 4 + ' against the flat side of the motor shaft using a 1 1 / 8 - inch hex " L " wrench . OIL PLUG f 5 . Place the Poly " V " belt into the motor mount as shown on the underside of the band saw . 6 , Look at the motor mount and find the slot that is MOTOR MOUNT narrower than the other three . When mounting the motor , the motor stud without a spacer goes into this slot . NARROW SLOT 13
Page: 14

t II / 7 . Carefully position the motor so that the poly " V " belt is around the motor pulley and the four \ motor studs align with the slots in the motor mount . 8 , Push motor studs through and install the flanged lock nuts to the three ( 3 ) motor studs with spacers . Start the flanged nuts by hand only at this time . MOTOR MOUNT MOTOR MOUNT 9 . Install the threaded stud through the hole in the lower leg of the motor mount and over the motor stud as shown . THREADED STUD MOTOR MOUNT 10 . Install a flanged lock nut onto this motor stud . Tighten the flanged lock nuts , using a 3 / 8 - inch wrench , until almost tight . NOTE : Do not over - tighten the flange nuts . The FLANGED motor should slide in the grooves to allow tensioning of the belt . LLEY 11 . Install the wing nut on the threaded stud . 12 . Check that the poly " V " belt is on both pulleys being sure that it is centered on each pulley . 13 . Check that the pulleys are in line by sighting down the side of the large pulley to see if it lines up with the small pulley . If the pulleys are not in line , loosen the set screw holding the pulley on the motor shaft and position the pulley , A notch in the small end of the motor support is provided for access to the set screw and belt . ACCESS FLANGED LOCK NUT WING NUT 14
Page: 15

14 . Belttensioningis doneby tighteningthe wing nut which pulls the motor down . The motor slides on the three ( 3 ) spacers and is locked in place by the flanged lock nut at the threaded stud . Belt tension is important . Over tensioning may cause vibration while too little tension may allow the belt to slip under heavy loads . TIGHTEN FLANGE NUT AFTER TENSIONING BELTWITH WING NUT CONNECTING THE MOTOR 1 . Next , the motor cord needs to be wired into the motor . Coming from the underside of the table TERMINAL will be a cord with a black , white and green wire . GREEN This is the motor cord . WARNING : FOR YOUR OWN SAFETY , NEVER PLUG 1 = HE SAW IN UNTIL ALL ASSEMBLY STEPS ARE COMPLETED . 2 . Loosen the two screws holding the connector BLACK WIRI box cover on the back side of the motor . Swing TERMINAL T1 the cover open . 3 . Install the green ground wire by removing the green grounding screw and inserting it through the round metal terminal on the green ground wire of the motor cord . Reinstall the green screwnd into the hole from which it was removed a GREEN WIRE - TO GREEN SCREW tighten securely . WARNING : TO AVOID ELECTROCUTION , STRAIN RELIEF NEVER CONNECT ANYTHING BUT THE GROUND WIRE ( COLORED GREEN ) TO THE WIRE TO TERMINAL T4 GREEN SCREW . 4 . Insert terminal end of WHITE wire on spade terminal marked T4 on the motor . Push terminal firmly until seated . 5 . Insert terminal end of BLACK wire on aspadel terminal marked T1 on the motor . Push termin firmly until seated . 6 . Close motor connector box being sure that power cord is seated in the largest strain relief groove and tighten box cover screws . 7 . DO NOT plug in power cord . 15
Page: 16

MOUNTING THE SAW TO THE CABINET 1 . From loose parts bag find the following hard - ware : ITEM DESCRIPTION QTY . A Truss Head Bolts 1 / 4 - 20 x 112 . . . . . . . . . . 4 o © c © B Lockwashers External 1 / 4 . . . . . . . . . . . . . . 4 C Hex Nuts 1 / 4 - 20 . . . . . . . . . . . . . . . . . . . . . . . 4 2 . Place saw on cabinet so that holes in bottom of saw line up with holes in top of cabinet . 3 . Install bolts , Iockwashers , and nuts as shown . Tighten securely using a 7 / 16 - inch wrench orr socket . The front two bolts hold the saw , lowe wheel cover , and the cabinet together . Install these bolts from the bottom side . 4 . After the band saw has been mounted to the cabinet , go back and tighten all the nuts that were previously hand tightened using a 7 / 16 - inch wrench or socket . ! t MOUNTING THE SAW TO THE LEG SET 1 . From loose parts bag find the following hardware : ITEM DESCRIPTION CITY . A Truss Head Bolts 1 / 4 - 20 x 1 / 2 . . . . . . . 4 o © c © B Lockwashers External 1 / 4 . . . . . . . . . . . 4 C Hex Nuts 1 / 4 - 20 . . . . . . . . . . . . . . . . . . . . 4 2 . Place saw on leg set so that holes in bottom of saw line up with holes in top of leg set . 3 . Install bolts , Iockwashers , and nuts as shown . Tighten securely using a 7 / 16 - inch wrench eorr socket . The front two bolts hold the saw , low wheel cover and leg set together . Install these bolts from the bottom side . 4 . After the band saw has been mounted to the leg set , go back and tighten all the nuts holding the leg set together . 16
Page: 17

ATTACHING TRIM CAPS & TRIM LEDGE 1 . Locate the two ( 2 ) trim caps , the trim ledge , and from loose parts bag six ( 6 ) screws 1 / 4 x 1 / 2 . 2 . Place the trim ledge against the bottom of the base , then reach through the base and secure the trim ledge with the two screws using a phillips screwdriver . TRIM LEDGE PHILLIPS SCREWDRIVER 3 . Position the trim caps in place and hold as illustrated . 4 . Then reach through the base and secure the trim cap with the two ( 2 ) screws using a phillips screwdriver . Repeat procedure for other side . TRIM CAP ATTACHING THE HANDWHEEL 1 . From loose parts bag find one ( 1 ) pan head screw 10 - 32 x 2 and one ( 1 ) hex nut . Install the hand - wheel . Reach inside the base to the back side of the bevel mechanism and put the nut in place . Hotd the nut in place with a finger . _ nstall the screw through the center of the handwheel and tighten with a phillips screwdriver . 2 . Hold the handle and pull the red release button with your finger to close the handle . 17
Page: 18

location and function of controls 2 1 TENSION ADJUSTMENT KNOB WARNING LABEL COVER 1 WARNING 8 LABEL GUIDE BAR TILT lARD SCALE BLADE GUIDES GAGE 4 SLOT BEVEL LOCK KNOB ' ABLE 7 5 6 4 BLADE GUIDES HANDWHEEL ON - OFF SWITCH 5 6 GUIDES 7 BACK - UP BEARING GETTING TO KNOW YOUR BAND SAW 6 . Lateral Blade Guide Adjustment - The guides 1 . Warning Labels . can be adjusted sideways and locked in position 2 . Tensions adjustment knob - Tightening the knob by the capscrews to prevent the blade from will increase the tension on the blade . Loosening twisting during operation . it will decrease the tension . Clockwise to tension , counter clockwise to loosen . 7 . Blade Backup Bearing Adjustment - The thrust bearings can be adjusted in or out for various 3 . Tension Scales - The fractional markings indicate widths of blades and locked in place by the the correct blade tension for various widths of setscrews . blades . For example , when installing a 1 / 4 - inch , Guide Bar Lock Knob - The upper blade guides wide blade , tighten the tension knob until the should just clear the workpiece while cutting . pointer is pointing to the 1 / 4 - inch marking . Always adjust the guides before turning on the 4 . Setting Bevel Angle - Pull the bevel lock knob band saw and lock the guide bar by tightening and adjust the band saw to the desired angle by the knob . turning the handwheel , then push in the bevel lock to secure . 5 . Blade Guide Adjustment - The guides can be adjusted in or out for various widths of blades and locked in place by the set screws . 18
Page: 19

INSTALLING THE BLADE 1 . Remove the blade guard by loosening the two ( 2 ) mounting screws with a phillips screwdriver and MOUNTING SCR EW lifting the blade guard upward . BLADE _ ING SCREW 2 . Loosen the upper blade guide assembly and lower to approximately 3 inches above rear table and retighten lock knob . This is necessary to make adjustments to blade guide and back up roller bearing . 3 . Loosen the two capscrews that lock the upper blade guides using a 1 / 8 - inch hex " L " wrench and separate them about 1 / 8 - inch . Repeat the BLADE GUIDE same step for the lower blade guides . CAPSCREWS UPPERBLADE 11 ( GUIDE SUPPORT I ) . [ - _ . L _ 4 . Loosen the setscrew which locks the blade guide support and push the support all the way back . SETSCREW _ _ Repeat for lower blade guide support . " - , , , \ " " , , J ! lJ } LJJ ( J ) ) ) 1 - - GUIDE SUPPORT . . . . _ - _ ' - _ SETSCREW 19
Page: 20

UPPER BACKUP 5 . Loosen the setscrew which locks the upper back BEARING SETSCREW up bearing and push the bearing all the way back . Repeat procedure for lower back up bear - ing . LOWER BACKUP BEARING SETSCREW L BLADE CENTERED CAUTION : To avoid being scraped , if the blade ON RUBBER TIRE should suddenly uncoil , wear safety goggles . Carefully uncoil the blade holding it at arms length . 6 . Uncoil the blade . 7 . Place the blade over the wheels with the teeth pointing downwards toward the table as shown . Make sure the blade is between the blade guides and is in the center of the rubber tires . NOTE : If the blade will not reach around both wheels , lower the upper wheel by turning the tension knob counterclockwise . ALIGNING THE BLADE AND BLADE GUIDE ASSEMBLIES This band saw comes equipped with a 1 / 4 - inch blade . This band saw can be used with blades of width from 1 / 8 - inch to 1 / 2 - inch . The alignment steps must be followed for proper tension , blade guide , and bearing adjustments for each different blade . Refer to the blade usage section for the recom - mended blade size for best results during most band saw operations . NOTE : It is critical to the life of the blade that the following steps are followed . Premature blade breakage will result if these steps are omitted . 1 . Turn the tension knob until the tension scale indicates 1 / 4 - inch position . This will set the correct tension for a 1 / 4 - inch blade . WARNING : TO AVOID INJURY FROM UNEX - f / PECTED STARTING OR ELECTRICAL SHOCK , DO NOT PLUG THE SAW IN . THE POWER CORD MUST REMAIN UNPLUGGED WHEN - EVER YOU ARE WORKING ON THE SAW . 20
Page: 21

2 . Turn the upper wheel by hand a few times andre notice if the blade remains in the center of the ti TRACKING ADJUSTMENT SCREW on the top wheel . If the blade moves away from the center of the tire while you are turning it , the blade is not tracking properly . The top wheel shaft is hinged so the blade can be tracked . Tilt the wheel by turning the tracking adjustment screw using a medium screw driver . ( See illustration . ) a . If the blade moves toward the front of the band saw : Turn the tracking adjustment screw clockwise about 1 / 4 of a turn , as though you were tightening it . b . If the blade moves toward the back of the band saw : Turn the tracking adjustment screw counter - clockwise about 1 / 4 of a turn as though you were loosening it . c . Check adjustment byturning wheel by hand a few times . Repeat adjustment if necessary . 3 . The upper and lower blade guides support the blade and keep it from twisting during operation . Adjust blade guide support whenever blades are changed or replaced with a different width . 4 . Push the blade guide support toward the blade and adjust the blade guides so they are about 1 / 32 - inch from the deepest part of the blade teeth . This deep part is called a gullet . Tighten the set screw locking the blade guide support . Turn the upper wheel , by hand , checking the position of the blade guide support . BLADE GUIDE NOTE : Letting the blade teeth hit the blade GULLET guides while using the band saw will ruin the blade . The set of the teeth and the sharpened edge of the teeth would be damaged . Proper adjustment of the upper and lower blade guide BLADE assemblies will prevent this from happening . BACKUP BEARING Repeat procedure for lower blade guide support . 5 . Slide the two blade guides evenly against the sides of the blade . Do not push the blade guides or pinch the blade guides against the blade . Rotate the upper wheel by hand so the blade travels downward . This leaves proper space for blade . Make sure one guide is not further from the blade than the other . Tighten both setscrews with a 1 / 8 - inch hex " L " wrench . Repeat proce - dure for lower blade guides . BLADE GUIDE BLADE GUIDE NOTE : The backup bearings support the blade from the rear and will spin when the blade is pushed against them while you are cutting . As soon as you stop cutting , the bearings should stop spinning . 21
Page: 22

6 . To insure the backup bearing is properly sup - ' 4 ' ' " ' - - " BLAD E I I porting the blade , push the bearing toward the z F BACKUP BEARIING I blade until it almost touches it . Turn the upper i wheel , by hand , checking the backup bearing to make sure it is not turning . If the bearing is turning the blade is too close . Move bearing slightly away from blade and tighten set screw " 1 with 1 / 8 " hex " L " wrench . Turn upper wheel and " 1 recheck the bearing . Adjust again if necessary . 7 . Repeat procedure for lower backup bearing . 8 . Turn upper wheel by hand and check the blade guides and backup bearings to make sure they z are adjusted correctly . Make any readjustments if necessary . J I 9 . Install blade guard and tighten with phillips screwdriver . ( See illustration , page 19 . ) FRONT COVER 10 . Install the front cover . Rest top edge of cover on two latch springs along the top edge of back cover . Swing cover down into position , engaging the three other latch springs . Push the front SPRING cover into position on the back cover . Check that the lip on the front cover completely overlaps the lip on the rear cover . _ 114 - 20 x 5 / 8 MOUNTING THE FRONT TABLE _ " * - . " _ - - - WASHER HEAD SCREW 1 . Turn front table over . Locate the two ( 2 ) latch . . . - . L = i _ - _ ' ' ' ' ' _ ALIGNMENT springs , two ( 2 ) alignment springs , and the four " ' _ T _ ' _ . . . _ SPRING ' , I _ LATCH SPRING ( 4 ) 1 / 4 - 20 x 5 / 8 hex washer head thread forming screws . 2 : Install the two latch springs on the front table as illustrated using a 3 / 8 - inch wrench or socket . Install the two alignment springs on the front table as illustrated using a 3 / 8 - inch wrench or socket . 3 . Locate the two ( 2 ) oval point setscrews 1 / 4 - 20 xll 1 / 2 and use an 1 / 8 - inch hex " L " wrench to insta , . . / HEX " L " WRENCH in the two holes , as illustrated , but do not allow j . l / 4 - 20X1 / 2 the screws to extend beyond the underside of the I _ OVAL pOINT table . y SETSCREW FRONT TABLE 22
Page: 23

PAN HEAD 4 . Locate the two ( 2 ) table latches , two ( 2 ) pan head SCR EW screws , Iockwashers , and hex nuts . Install the table latches to the front of the base in holes provided . _ FRONTTABLE LATCH , _ - - 1 / 4 - 20X 1 _ _ HEAD CAPSCREW 5 . Locate the table alignment key and the two ( 2 ) 1 / 4 - 20 x 1 low head capscrews . Install the key under the rear table miter gage slot and install the two screws but do not tighten at this time . y TABLE ALIGNMENT KEY 6 . Mount the table to the base as follows : a . Hold the front edge of the table . Position the FRONT TABLE rear edge of the table so that the two flat springs slip under the two tabs on the rear table . b . Line up the miter gage slots in the front and rear tables . o . Push the front edge of the table backward and downward until the table snaps into position . 7 . Use a 1 / 8 - inch hex " L " wrench to adjust the two leveling setscrews to bring the rear edge of the front table up to the same height as the front edge of the rear table . TABLE LEVELING SETSCREWS 23
Page: 24

8 . To keep the miter gage grooves in line , use a flat blade screwdriver against the head of one of the low head capscrews in the miter gage groove to force the table alignment key firmly forward into the notch in the front table . 9 . While holding the alignment key into the notch , tighten the other capscrew . Remove the screw - driver and tighten the remaining screw . Check that the miter gage grooves line up . 10 . Check the operation of springs and tabs by removing the front table and reinstalling . Remove the table by lifting up on two spring tabs under front edge of the table until springs are free , then pulling forward . SQUARING THE BLADE TO THE TABLE To assure repeatability and accuracy , it is important to square the blade to the table and adjust the 0 ° position stop . This will guarantee that the blade will return to the square position after the head has been moved for a bevel cut . 1 . Locate the 1 / 4 - 20 x 1 / 2 oval point setscrew and 0 r STOP SETSCREW use an 1 / 8 - inch hex " L " wrench to install it in the hole located atthe left front of the rear table . The COMBINATION setscrew has a lock patch that will make it hard to SQUARE turn . 2 . Slide the upper blade guard to its top most position and tighten knob . f 3 . Release bevel lock by pulling out bevel lock knob under left front edge of table . 4 . Place a combination square on the table against HEX " L " WRENCH the blade . Adjust the position of the blade to the table by turning the handwheel . When the blade is flush against the combination square lock ctheh bevel lock knob . Use a 1 / 8 - inch hex " L " wren to set the 0 ° stop . Turn screw until it makes contact with the frame . 5 . Unlock bevel lock , bevel the blade , then return to 0 ° position . Push in bevel lock knob and recheck blade to make sure it is square to the table . NOTE : The combination square must be " true " - - see the beginning of the unpacking and checking contents section for checking the combination square procedure . 24
Page: 25

location and function of controls ON - OFF SWITCH NOTE : The On - Off switch has a locking feature , This feature is intended to help prevent unauthorized and possibly hazardous use by children and others . 1 . Insert yellow key into switch . 2 . To turn on , insert finger under end of red switch lever and pull end out . 3 . To turn off switch , push red lever in towards the base . 4 . WARNING : The locking feature provided is to help prevent unauthorized use of your saw . Always remove the yellow key and keep it in a safe place . To remove yellow key , hold thumb on 2 the end of red lever to keep switch in " Off " position and pull yellow key straight out . 3 / / TILTING HEAD FOR BEVEL CUT 1 . Unlock bevel lock by pulling outon knob located under the left front edge of the table . 2 . Turn handwheel counter - clockwise to increase the tilt angle of the blade . The bevel scale printed on the front cover shows the approximate angle and is read at table level . 3 . Lock the bevel lock by pushing in on knob until it is fully seated when desired bevel angle is reached . BEVEL SCALE BEVEL LOCK KNOB HANDWHEEL ADJUSTING BEVEL LOCK KNOB MOUNTING FRAME BEVELLOCK KNOB The bevel lock knob is factory adjusted and set . If after repeated use it becomes necessary to adjust : 1 . Pull the bevel lock foward and bevel the band saw to 25 degrees . 2 . Use a 9 / 16 - inch wrench or socket to adjust the locking nut behind the band saw mounting frame . Turn nut clockwise to tighten . LOCKNUT 3 . Recheck bevel lock knob and readjust if neces - sary . HANDWHEEL 25
Page: 26

basic band saw operation WARNING : FOR YOUR SAFETY , COMPLY WITH Operation Recommended Blade Size ALL THE SAFETY INSTRUCTIONS ON PAGES 2 - 4 ( Inches ) BEFORE USING THE BAND SAW . Cross Cutting 1 / 4 , 3 / 8 , 1 / 2 Ripping 1 / 2 A band saw is basically a " curve cutting " machine . It Mitering 1 / 4 , 3 / 8 , 1 / 2 is not capable of doing inside cutting . Beveling 1 / 4 , 3 / 8 , ! / 2 Your Craftsman Band Saw is not only capable of the Compound Cutting 1 / 4 , 3 / 8 , 1 / 2 usual band saw operations , but it can be converted Circle Cutting See Chart Below into a sander as well . You can finish wood , certain Resawi ng 1 / 2 compositions and plastics . Curve Cutting 1 / 8 , 1 / 4 It is also used for straight - line cutting operations such as crosscutting , ripping , mitering , beveling , compound cutting , and resawing . BLADE SELECTION GUIDE FOR MINIMUM CIRCLE CUTTING CIRCLE CUTTING 1 . Adjust the upper guides to just clear the work - piece . 2 . Use both hands while feeding the work into the blade . Hold the workpiece firmly against the table . Use gentle pressure , and do not force the work , but allow the blade to cut . 1 / 2 " " D CIRCLE DIM , 3 . The smallest diameter that can be cut out is BLADE SIZE determined by the width of the blade . For example , a 1 / 4 - inch wide blade wilt cut a mini - mum diameter of approximately 1 - 1 / 2 - inch ( see chart ) . 26
Page: 27

SAWDUST COLLECTION 1 . There is an opening provided in the rear of the bottom cover to attach a 2 - 1 / 2 - inch hose from a wet / dry vac to control sawdust . I SAWDUST COLLECTION I _ NING UPPER BACKUP INSTALLING SANDING ATTACHMENT NOTE : The sanding belt cuts very rapidly . Practice with some scraps of wood first before you attempt to sand your actual workpiece . , _ NG SETSCREW 1 . To install the sanding belt and sanding platen , remove the front table , front cover , blade guard , and the blade . 2 . Use a 1 / 8 - inch hex " L " wrench and remove the upper and lower right blade guides . The mount - ing screw used for the upper blade guide will be used to hold the sanding platen in place . 3 . Loosen the setscrews that hold the upper and lower backup bearings in place and push the bearings all the way back , Tighten setscrews so bearings will remain . 4 . Slide the sanding platen into the blade slot in the table and fasten to the upper blade guide J assembly where the right blade guide mounts . It may be necessary to loosen the left blade guide UPPER BLADE and slide it backwards until platen is in place . GUIDE ASSEMBLY 5 . Slide the upper left blade guide towards the sanding platen and tighten mounting screw securely . 6 . Slide the lower left blade guide towards the sanding platen until the platen rests 1 / 8 - inch away from the right edge of the slot in the work table . SANDING PLATE 27
Page: 28

INSTALLING THE SANDING BELT 1 . Install the sanding belt and adjust tension to the sanding position . ( The letter " S " on the scale . ) 2 . Rotate the upper wheel by hand ( clockwise ) to check the sanding belt tracking . Adjust tracking if necessary . ( Reference the blade tracking sec - tion for tracking procedure . ) SANDING BELT 3 . After tracking the sanding belt if the belt and the platen do not align loosen the upper blade guide support and slide the support in or out to align . Then tighten set screws to hold support and p { aten in place , It may also be necessary to adjust the lower blade guide support to align the blade guide with the sanding platen . NOTE : A new sanding belt will stretch with use , so OO check the tension often . recommended accessories Caster Set for Cabinet . . . . . . . . . . . . . . . . . . . 9 - 22254 Caster Set for Leg Set . . . . . . . . . . . 9 - 22222 , 9 - 22221 Miter Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 29929 Hold - Down Clamp for Miter Gauge . . . . . . . 9 - 29928 Stop - Rods for Miter Gauge . . . . . . . . . . . . . . 9 - 29924 Rip Fence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 23402 Blades and Sanding Belts . . . . . . . . . . . . See Catalog Circle Cutting Attachment . . . . . . . . . . . . . . . 9 - 23411 Power Tool Know How Handbooks Radial Saw ( includes band saw section ) . . 9 - 2917 Table Saw ( includes band saw section ) . . . 9 - 2918 The recommended accessories listed here are cur - rent and were available at the time this manual was printed . 28
Page: 29

maintenance General Maintenance WARNING : FOR YOUR OWN SAFETY , TURN SWITCH " OFF " AND REMOVE PLUG FROM POWER Keep your band saw clean . Remove the sawdust SOURCE OUTLET BEFORE MAINTAINING OR from the inside . Vacuum or blow out frequently , LUBRICATING YOUR BAND SAW . Do not allow filth to build up on the table , the guides Tires orthe back - up bearings . Clean them with Craftsman Gum and Pitch Remover . Pitch and sawdust that build up on the tires should be removed with a stiff brush or scraped off with a CAUTION : Do not immerse the backup bearings in piece of wood . the gum and pitch remover . CAUTION : To avoid damaging the tires do not use a Put a thin coat of paste wax on the table so that the sharp knife or any kind of solvent . wood slides easily while cutting . When the tires become worn they should be replaced . Light Bulb When replacing the tires , stretch them around the To replace the light bulb remove the front cover , Use wheels but do not glue them on . a phillips screwdriver to remove the lens and replace the bulb . The light bulb is a 25 watt bayonet mount ADJUSTING BAND SAW BEVEL TRAVEL bulb . If the band saw will not hold its position when at a Motor bevel angle , and before the bevel lock is locked , or if it is difficult to change the bevel angle , an adjustment Frequently blow or vacuum out any sawdust from the motor . Follow lubrication instruction on the is necessary to correct the force required to bevel the band saw . motor label . WARNING : TO AVOID EYE INJURY FROM BLOW - To adjust the force required to bevel the band saw , locate the three ( 3 ) capscrews holding the frame to ING DEBRIS , WEAR SAFETY GOGGLES WHEN BLOWING OUT SAWDUST . the motor mount . The capscrews are located in the recessed area behind the hub of the lower wheel at WARNING : TO AVOID ELECTROCUTION OR FIRE , the 2 o'clock , 6 o'clock , and 10 o'clock positions . Use IMMEDIATELY REPLACE A WORN , CUT , OR a 3 ! 16 - inch hexagonal " L " wrench that has a 4 - inch DAMAGED POWER CORD . leg , reach between the spokes of the lower wheel to Lubrication the capscrews . Adjust the capscrews equally tuntils the bevel action is smooth and the saw will hold i All of the ball bearings are packed with grease at the position before the bevel lock is locked . factory . They require no further lubrication . ADJUSTING THE UPPER BLADE GUIDE TRAVEL WIRE CONNECTOR BLACK If the upper guide bar will not move up and down easily or falls when the lock knob is loosened , the SWITCH ( 3 REQ ) - - - _ CORD following adjustment should be performed . 1 . Remove the Guide Bar Lock Knob and the washer which is under it . BLACK BLACK 2 . Using a 7 / 16 " socket or wrench , tighten the nut which is under the washer to just tight . CORD W / PLUG 3 . Then loosen the same nut 1 turn . GRE 4 . Move the guide bar up and down to check for smooth movement while still holding its position CORD when released . BLACK 5 . Make further adjustments to the nut as required to get the guide bar to move smoothly and hold its position when released . WIRING DIAGRAM 6 . Reinstall the washer and Guide Bar Lock Knob . 29
Page: 30

trouble shooting WARNING : FOR YOUR OWN SAFETY , TURN SWITCH " OFF " AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE TROUBLE SHOOTING YOUR BAND SAW / SANDER . REMEDY PROBABLE CAUSE TROUBLE . Adjust tracking , see Assembly Section , Blade does not run in 1 . Not tracking properly . " Installing the Blade . " the approximate center o ! the upper wheel . ; 1 . 1 . Lower wheel not Reposition the wheel by loosening setscrew Blade does not run in and slide wheel in or out to allow blade to run positioned correctly on the approximate center in center of wheel . shaft . of the lower wheel . 1 . Adjust belt tension , see Assembly Section 1 . Belt too loose . Band Saw slows down " Installing and Aligning the Belt . " when cutting . 2 . Stop feeding , and back up the material slightly , ! 2 . Cutting too small a radius . until the band saw speeds up . . Dull blade . 3 . Replace blade . 4 . 4 . Slow down , trying to cut too fast . Overloading motor . 1 . Too much tension on 1 . Adjust tension . See Getting To Know Your Blades breaking . Band Saw . blade . 2 . Use correct cutting technique . See Basic , Kink in blade caused by Band Saw Operation Section . cutting too small a radius or turning the material too fast when cutting . Blade dulls too quickly . 1 . Blade guides set too close 1 . Adjust upper and lower blade guides . See Assembly Section " Installing the Blade . " to teeth . 2 . Cutting incorrect material . Too much tension on Band saw vibrates . 1 . 1 . Adjust according to " Installing and Aligning motor belt . Po ! Y " V " Belt " section . 3O
Page: 31

TROUBLE SHOOTING - - MOTOR NOTE : Motors used on wood - working tools are particularly susceptible to the accumulation of sawdust and wood chips and should be blown out or " vacuumed " frequently to prevent interference with normal motor ventilation and proper operation of the centrifugally - operated starting switch . TROUBLE PROBABLE CAUSE REMEDY Excessive noise . 1 . Motor . 1 , Have motor checked by qualified service technician . Repair service is available at your nearest Sears store . Circuit overloaded with Motor fails to develop 1 . 1 . Do not use other appliances or motors on lights , appliances and same circuit when using the saw . lull power . NOTE : other motors . LOW VOLTAGE : ( Power output of motor Undersize wires or circuit decreases rapidly with 2 . 2 . Increase wire sizes , or reduce length of wiring . too long . See " ' Motor Specifications and Electrical decrease in voltage at motor terminals . For Requirements " section . example , a reduction of 3 . General overloading of 3 . Request a voltage check from the power 10 % in voltage causes power company company . a reduction of 19 % in facilities . maximum power output of which the motor is capable , and a reductior of 20 % in voltage causes a reduction of 36 % in maximum power output . ) Motor starts slowly 1 . Low voltage . 1 . Request voltage check from the power or fails to come up company . Check size of circuit wiring . to full speed , 2 , Windings burned out 2 . Have motor repaired or replaced . or open . 3 . 3 . Blow out sawdust from motor . Have motor Starting switch not operating . repaired . Motor overheats . 1 . Motor overloaded . 1 . Feed work slower into blade . 2 . Improper cooling ( Air 2 . Clean out sawdust to provide normal air circulation restricted circulation through motor . See " Maintenance and Lubrication " section . through motor due to sawdust accumulation . Burned switch contacts Starting switch in 1 . 1 . Have switch replaced and request a voltage motor will not operate . ( due to extended hold - in check from the power company . periods caused by low line voltage , etc . ) 2 . Shorted capacitor . 2 . Have capacitor tested and replace if defective . 3 . Loose or broken 3 . Have wiring checked and repaired . con nections . Motor stalls 1 . Starting switch not 1 . Have switch replaced . ( resulting in blown operating . fuses or tripped 2 . Voltage too low to permit 2 . Request voltage check from the power circuit breakers ) . motor to reach operating company . speed . 3 . Fuses or circuit breakers 3 . Install proper size fuses or circuit breakers . do not have sufficient capacity . Motor overloaded . 1 , Feed work slower into blade , Frequent opening of 1 . . fuses or circuit 2 Fuses or circuit breakers 2 . Install proper size fuses or circuit breakers , breakers . do not have sufficient Check that wiring will handle toad . capacity . 3 . Starting switch not 3 . Have switch replaced . Blow out sawdust . operating ( motor does not reach speed ) . 31
Page: 32

W PARTS LIST FOR CRAFTSMAN 12 - INCH BAND SAWS MODELS 113.247210 AND 113.247310 18 19 6O 6 10 \ 2 58 41 35 43 42
Page: 33

PARTS LIST FOR CRAFTSMAN 12 - INCH BAND SAWS MODELS 113.247210 AND 113.247310 Always order by Part Number - Not by Key Number FIGURE 1 - DRIVE ASSEMBLY PARTS Key Part Key Part No . No . Description No . No . Description 1 507830 32 814083 - 2 Cover , Front w / Label • - Nut , Push 5 / 16 2 9 - 26595 33 tBlade , Band Saw 816352 Trunnion 3 41815 Tire 34 815865 - 2 Screw , Hex Wash Hd . 4 816600 1 / 4 - 20 x 5 / 8 Screw , SI . Hd . Set 5 / 16 - 18 x 2 - 1 / 8 35 816362 Slide Assembly , Lower 5 STD582062 * Ring , Retaining 5 / 8 ( Includes Key # 32 & 33 ) 6 41711 36 816356 Washer , Spring Shaft , Bearing Support 7 805034 37 816365 Bearing , Ball Support , Guide 8 816419 - 2 38 STD502502 • Screw Soc . Set 1 / 4 - 20 x 1 / 4 Wheel , Upper 9 41812 39 808819 - 1 Ring , Retaining 1 - 3 / 8 Ring , Retaining 10 STD541431 4O STD315485 * Nut , Lock 5 / 16 - 18 • Bearing Ball 11 41 STD551031 814083 - 1 * Washer , 21 / 64 x 5 / 8 x 1 / 32 - kNut , Push 5 / 16 12 816364 42 816379 Support Assembly , Guide , Blade 43 60334 Upper Wheel Screw , Socket Button 15 816446 Screw , Blade Tension Cap No . 10 - 32 x 3 / 4 44 3 / 8 - 16 x 10 - 1 / 4 69059 Wheel , Drive 14 816437 45 STD580103 Knob , Blade Tension • Key , 3 / 16 Sq . x ! 5 / 16 15 816350 46 816387 Shaft , Lower Wheel Plate , Support 16 808380 - 5 47 Screw , Pan Hd . STD315238 • Bearing , Ball Plastite # 8 x 3 / 4 48 816363 Slide Assembly , Upper 17 816433 Frame 49 816349 Follower 18 816453 5O 816358 Plate , Pivot Support Nut , Heavy Square 3 / 8 - 16 19 STD533110 51 816377 * Bolt , Carriage High Strength Indicator , Tension 5 / 16 - 18 x 1 52 STD551037 • Washer , . 380 x . 750 x . 03 20 816464 53 816353 Latch , Cover Spring , Blade Tension 21 816429 54 816361 Cover , Rear Lock , Slide 22 808447 - 2 Washer , Wave 3 / 8 x 3 / 4 x . 016 55 109093 Bolt , Carriage 1 / 4 - 20 x 1 - 3 / 4 23 60128 56 816388 Washer , 17 / 64 x 5 / 8 x 1 / 32 Guard , Blade 24 STD541425 * Nut , Lock 1 / 4 57 813786 - 2 Screw , Pan Cross Hd , 25 805552 - 20 Washer 17 / 64 x 1 x 1 / 16 Type " TT " No . 8 - 32 x 5 / 8 26 816435 58 Knob , 1 / 4 - 20 9 - 22361 i tBelt , Sanding 1 / 2 x 80 27 816444 59 816368 Socket , Light Platen , Sanding 28 808335 - 2 Retainer 6O 816606 Scale , Bevel 29 STD372252 SP5086 * Bulb , Light Owners Manual ( Not Ills . ) 3O 816380 Lens 31 808380 - 1 Screw , Pan Hd . Plastite No . 6 x 3 / 8 * Standard Hardware Item may be Purchased Locally . tStock Item - May be secured through the Hardware Department of most Sears Retail Stores or Catalog Order Houses . * If this part is removed , discard and replace with a new push nut . 31
Page: 34

PARTS LIST FOR CRAFTSMAN 12 - INCH BAND SAWS MODELS 113.247210 AND 113.247310 3 / 4 35 33 39 32 11 \ 16 7 28 22 FIGURE 2 34
Page: 35

PARTS LIST FOR CRAFTSMAN 12 - 1NCH BAND SAWS MODELS 113.247210 AND 113.247310 Always order by Part Number - Not by Key Number FIGURE 2 - BASE COMPONENTS Part Key Key Part No . No . Description No . No . Description 1 816434 Table , Front 22 815935 Screw , Pan Cross Type " BT " 2 1 / 4 x 1 / 2 806036 - 2 Screw , Locking Set 1 / 4 - 20 x 1 / 2 23 63467 Cap , Flag Terminal 60419 816421 Table , Rear 24 Screw , Pan Hd . ( Model 113.247210 ) Plastite No . 8 x 1 / 2 1816420 Table , Rear 25 815869 Cap , Trim L . H . 815881 ( Model t 13.247310 ) 26 Cap , Trim R . H . 816423 Cover Base 27 507749 Trim . Ledge w / Label 808380 - 2 ( Model 113.247210 ) 28 Screw , Pan Hd . Plastite No . 8 x 3 / 8 810214 - 2 Screw , Low Hd . Cap 1 / 4 - 20 x 5 / 8 29 STD610805 * Screw , Pan Hd . 7 1816371 Key , Table Alignment Ty AB # 8 x 1 / 2 8 816370 Spring Table Alignment ( Model 113.247210 only ) 9 816372 815865 - 2 Screw , Hex Washer Hd . 30 Plate , Cover Type " TT " 1 / 4 - 20 x 5 / 8 31 816436 Cord , Switch 10 _ 816448 816442 Spring , Table Latch 32 Cord , w / Plug 11 ; 816888 816417 Cover , Bottom 33 Cord , Motor 12 169123 - 12 816418 Base Assembly 34 Relief , Strain 13 815868 805589 - 5 Screw , Pan Hd . 35 Relief , Strain 1 / 4 - 20 x 1 / 2 36 816333 - 2 Screw _ , Pan Hd . 14 816441 Latch , Table Ty TT 10 - 32 x 3 / 8 15 ISTD522505 STD541110 * Nut , Hex 10 - 32 37 * Screw , Hex Wash Hd . 16 1 / 4 - 20 x 1 / 2 STD551225 * Lockwasher , Ext . 1 / 4 17 62204 816113 Switch , Locking 38 Clip , Cord 18 816403 Box , Switch 39 STD375006 * Connector , Wire 19 STD511105 * Screw , Pan Cross 10 - 32 x 1 / 2 40 STD551210 * Lockwasher , Int . # 10 20 507655 815863 Key , Switch Bag of Loose Parts ( Not Ills . ) 21 STD541025 l'Nut , Hex 1 / 4 - 20 * Standard Hardware ttem may be Purchased Locally . 35
Page: 36

PARTS LIST FOR CRAFTSMAN 12 - INCH BAND SAWS MODELS 113.247210 AND 113.247310 41 42 iS 9 26 I0 \ 31 30 32 IO 25 27 34 35 38 4O 39 FIGURE 3 36
Page: 37

PARTS LIST FOR CRAFTSMAN 12 - INCH BAND SAWS MODELS 1 ! 3.247210 AND 113.247310 Always order by Part Number - Not by Key Number FIGURE 3 - BEVEL DRIVE AND MOTOR MOUNT ASSEMBLY PARTS Part Key Part Key No . No . Description No . Description No . Screw , Pan Hd . 10 - 32 x 2 24 809372 - 18 1 816499 Handwheel Assembly STD541110 Nut , Hex 10 - 32 25 Knob , Bevel Lock 2 i 816386 26 } 16504 Support Frame 3 Pinion , Handwheel 88163814 Washer , Plastic 2.53 x 6 x 03 27 8 ! 6354 - 1 4 ! 8163 Gear , Handwhee ! 816422 Mount , Motor 28 Cover . Bevel Gear 5 816543 STD580103 29 " Key3i16Sq x 15,16 Shaft , Bevei 6 816382 3O 816389 Pulley , Polyrib 4 in ST D571207 * Pin . Roll 1 / 8 x 3 / 4 7 * Screw , Set 5 / ! 6 - 18 x 1 / 2 31 STD503105 8 815865 - 2 Screw , Hex Washer Hd 816439 - 2 32 Belt , Poly V Ty TT 1 / 4 - 20 x 5 / 8 Motor 816613 33 Nut , Lock 3 / 8 - 16 9 9414202 34 802392 - 25 Spacer , Motor Mount 10 805556.23 Washer , . 380 x 750 x . 03 # 10 x 5 / t6 11 816452 Spacer 9 / 16 x 1 / 4 35 816369 Pulley , Polyrib 1 in . Washer , 21 / 32 x 1 x ! / 64 12 60317 36 816815 Stud , Belt Tension 13 816443 Gear , Segment " Nut , Die Cast Wing 5 / 16 x ! 8 37 STD54163 ! 14 816348 Pinion , Bevel Drive 38 816817 Nut , Hex Flange Lock 10 - 32 15 802392 - 38 Spacer 1 / 2 x 2 39 816354 Washer , Plastic 3.8 x 6 x 03 16 805562 - 1 Washer , . 507 x 1.25 x . 125 40 816445 Bushing , Rubber 17 60208 _ Nut , Push 1 / 4 * Washer 17 / 64 x 1 / 2 x 1 / 32 4 ! STD55 ! 012 18 60240 _ Nut , Push 3 / 8 42 815992 - 1 Screw , Hex Socket Head 19 816360 Cam , Bevel Lock Ty " TT " 1 / 4 - 20 x 3 / 4 20 816359 Mount , Bevel Lock 43 STD551125 * Lockwasher 1 / 4 21 816465 Spacer 1 / 2 x . 59 44 STD502505 " Screw , Soc . Set 1 / 4 - 20 x 1 / 2 Rivet 1 / 4 x 1 - 1 / 8 22 815774 - 3 23 60419 Screw , Pan Hd . Ptastite No . 8 x 1 / 2 " Standard Hardware Item may be Purchased Locally . _ lf this part is removed , discard and replace with new push nut . 37
Page: 38

PARTS LIST FOR CRAFTSMAN 12 " BAND SAW MODEL NO . 113.247310 FIGURE 4 - PARTS LIST 23 " CABINET Always order by Part Number - Not by Key Number 2 j 7 6 3 1 Part Key No . Description No . 1 805589 - 5 Screw , Truss Hd . 1 / 4 - 20 x 1 / 2 2 815900 Ski rt 23 " 3 815887 Shelf , Lower 23 " 4 817151 Panel Side R . H . 5 816111 Cover 6 STD541025 * Nut , Hex 1 / 4 - 20 7 STD551225 * Lockwasher , Ext . 1 / 4 8 , 817108 Spacer 9 STD541237 * Nut , Hex Jam 3 / 8 - 16 10 803835 - 1 Foot , Leveling 11 815993 Bracket , Corner 12 816063 Stiffener , Shelf Panel Side L . H . 13 817150 507755 Bag of Loose Parts ( Not . Ills . ) * Standard Hardware Item may be Purchased Locally . 38
Page: 39

PARTS LIST FOR CRAFTSMAN 12 " BAND SAW MODEL NO . 113.247210 FIGURE 5 - PARTS UST LEG SET Always order by Part Number - Not by Key Number \ I 8 7 \ \ Key Part No . No . Description 1 ! 815918 Stiffener , Leg 2 8171O5 Leg 3 Stiffener , Lower 1815909 I 4 STD541237 * Nut , Hex Jam 3 / 8 - 16 5 1803835 - 1 Foot , Leveling 6 805589 - 5 Screw Truss Hd . 1 / 4 - 20 x 1 / 2 7 STD551225 * Lockwasher , Int . 1 / 4 8 STD541025 * Nut , 1 / 4 - 20 507498 Bag of Loose Parts ( Not . Ills . ) * Standard Hardware Item may be Purchased Locally . 39
Page: 40

SEARS owners 12 - 1NCH BAND SAW manual SERVICE Now that you have purchased your fl2 - Inch Band Saw , should a need ever exist for repair parts or service , simply contact any Sears Service Center and most Sears , Roebuck and Co . stores . Be sure to provide all pertinent facts when you call or visit . MODEL NO . The model number of your 12 - Inch Band Sawwill Ioe found on a plate attached to your saw , at the left - hand side of the base . 113.247210 BAND SAW WITH LEG SET MODEL NO . ! ! 3.2473 ! 0 BAND SAW WITH CABINET WHEN ORDERING REPAIRPARTS , ALWAYS GIVE THEFOLLOWING HOW TO ORDER INFORMATION : REPAIRPARTS PARTDESCRIPTION PARTNUMBER NAME OF ITEM MODEL NUMBER 12 - Inch Band Saw 113.247210 or 113.247310 All parts listed may be ordered from any Sears Service C _ nter and most S _ ars stores , if the parts you need are not stocked locally , your order will be electTonically transmitted to a Sears Repair Parts Distribution Center for handling , Sold by SEARS , ROEBUCKAND CO . , Chicago , IL . 60684 U . S . A . Part No . SP5086 Form No . SP5086 - 3 Printed in U . S . A . 4 / 89
Search in Band Saw on ebay
"