Home | Register Login | Wanted Manuals | MarketPlace | Members Area | Manuals Manufacturer Directory | UPC Lookup | Information Pages | Policy


Back To Craftsman Routers       Model: 113.251890 or 113251890 Craftsman Router Recreator
Regular Text Search or Search by Model Number

Register / log-in to add to your Hammerwall Collection.
Manual Location


This is a partial text extraction from the pdf, to download the pdf, click the Manual tab. If you want to search this text, hold control and F, and type the word you are looking for.

Page: 1

ROUTER - RECREATOR Serial SHOWN WITH SEARS ROUTER Number . . . . . . . . . . . . AND LEG SET Model and serial number may be found on a pfate attached to the yoke assembly . You should record both model and serial number in a safe place for future use . ROUTER - RECREA TOR CAUTmON : Read GENERAL and ADDITIONAL ® assembly SAFETY . . . . iNSTRUCTIONS ® operating carefully o repair parts Sold _ by SEARS , ROEBUCK AND CO . , Chicago , 1L . 60684 U . S . A . Part No . 76005
Page: 2

This warranty g Yes you specif c egal rights , and you may also have other rights which vary from State to state ; _ SEARSI ROEBUCK AND CO . , DEPT . 69B / 731A Sears ToWer . Chicago , IL 60684 Before = operating the Recreator read and understand your Router and Router Recreator owner's manuals and affixed warnings . The General Safety Instructions which follow apply to your Router and Router Recreator co mbinaUon as a " power tool . " genera ! l safety instructions for power tools 1 . KNOW YOUR POWER TOOLner's USE SAFETY GOGGLES Read and understand the ow manual and 12 . Safety goggles must comply with ANSI labels affixed to the tool Learn its applicationial Z87 . 1 - t968 , Also use face or dust mask if and limitations as well as the specific potent cutting operation is dusty . Everyday hazards peculiar to this tool . eyeglasses only have = mpact resistant lenses , 2 . GROUND ALL TOOLS UNLESS they are not safety glasses . DOUBLE INSULATED 13 . SECURE WORK If tool is equipped with an approved Use clamps or a vise to hold work when 3 - conductor cord and a 3 - - prong grounding practical , it's safe r than using your hand , frees type pug to fit the proper grounding typeis both hands to operate toot . receptacle . The green conductor in the cord DON'T OVERREACH the grounding wire . Never : connect the green 14 . wire to a live terminal Keep proper footing and balance at all ttmes . 3 , KEEP GUARDS iN PLACE 15 . MAINTAIN TOOLS WITH CARE and in working order . Keep tools sharp and clean for best and safest performance . Follow instructions for 4 . REMOVE ADJUSTING KEYS lubrication and changing accessories . AND WRENCHES DISCONNECT TOOLS Form habit of checking to seethat keys and 16 . before servicing ; when changing accessories adjusting wrenches are removed f , rom tool Such as blades , bits , cutters , _ tc . before tui'ning it on . : i : - : 5 ; KEEP WORK AREA CLEAN : 17 . AVOID ACCIDENTAL oSTARTINGsition Cluttef ; ed areas and benches nv te accidents . Make sure switch is in " OFF p before Ftoor must not be slippery dueto wax : or plugging in . USERECOMMENDEADCCESSORIES sawdust . - - 18 . Consult the owner's manual for recommended 6 , AVOID DANGEROUS ENVIRONMENT accessories . Follow the instructions that Don't use power tools in damp or wet location . accompany the accessories . The use of Keep work area well lit . Provide adequate tmprope _ " accessories may cause hazards . surrounding work space . NEVER STAND ON TOOL 7 . KEEP CHILDREN AWAY 19 . AH visitors should be kept a safe distance from Serious injury could occur if the toot is dtipped . or if the cutting tool is accidentally contacte work area , Do not store materials above or near the tool 8 . MAKE WORKSHOP KID - PROOF such that it is necessary to stand on the tool to - - with padlocks , master switches , or by reach them . removing starter keys . 20 . CHECK DAMAGED PARTS 9 . DON'T FORCE TOOL Before further use of the tool , a guard or other It wit ! do the job better and safer at the rate for part that is damaged should be rcarefullyly which it was designed . checked to ensure that it will operate prope 10 . USE RIGHT TOOL and perform its intended function , Don't force tool or attachment to d o a job it was Check for alignment of moving parts , binding not designed for . of moving parts , breakage of parts , mounting , and any other conditions that may affect its WEAR PROPER APPAREL operation . A guard or other part that as No loose clothing , g oves , neckties or jewelry to be properly repaired or get : caught in moving , parts . Rubber - soled damaged should footwear is recOmn _ ended fop best footing replaced .
Page: 3

additional safety instructions for router - recreator 3 . KEEP HANDS CLEAR OF BITS 1 . ALWAYS USE EYE PROTECTION . AND WORKING AREA . The operation of any cutting tool can result in foreign objects being thrown into the eyes , which can result in severe eye damage . Always 4 _ KEEP ROUTER RECREATOR AND wear safety goggles complying with ANSIl ROUTER CLEAN Z87 . ! before commencing cutting too After every use , clean saw dust off the operation . We recommend Wide Vision Safetyrs Recreator and Router , Mask for use over goggles . . , available at Sea NOTE : Motors used onwood - working tools are retail or catalog stores . particularly susceptible to the accumulation nofnt 2 . DON'T FORCE TOOL sawdust and wood chips and shouid be vblowe The Recreator was designed for smooth out or " vacuumed " frequently to pren . operation , therefore , parts should never be interference with normal motor ventilatio forced to operate . Note and follow the instructions found on the WARNING label which appears on the yoke assembly . WARNING FOR YOUR OWN SAFETY 1 . READ AND UNDERSTAND OWNER'S MANUAL OF ROUTER RECREATOR AND ROUTER BEFORE OPERATING MACHINE . 2 . WEAR SAFETY GOGGLES AND EAR PROTECTION . 3 . DO NOT WEAR GLOVES , NECKTIE , OR LOOSE CLOTHING . TIE BACK LONG HAIR . 4 . EXCEPT FOR SPINDLE WORK NEVER USE A SMALLER DIA . STYLUS TiP THAN THE CUTTER . 5 . BE POSITIVE YOU DO NOT RUN CUTTER INTO C - CLAMPS . WEAR YOUR The operation of any power tool can result in foreign objects being thrown into the eyes , which can results in severe eye damage . Always wear safety goggle complying with ANSI Z87 , 1 ( shown on Package ) before commencing power tool operation . Safety Goggles are available at Sears retail or catalog stores . CONTENTS Installing the Pulley Guards . . . . . . . . . . . . . 12 General Safety Instructions . . . . . . . . . . . . . . . . 2 Mounting Your Router - Recreator to a Stand . ! 2 Additional Safety Instructions . . . . . . . . . . . . . 3 Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ! 3 Introduction . . : . . . . . . . . . . . . . . . . . . . . . . . . 4 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Unpacking and Checking Contents . . . . . . . . . . 4 Genera ! Operating Hints . . . . . . . . . . . . . . . . 15 Getting to Know Your Router - Recreator . . . . . 4 Three Dimensional Carving . . . . . . . . . . . . . . 216O Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Base Assembly . . . . . . . . . . . . . . . . . . . . . . . 5 Sign Making . . . . . . . . . . . . . . . . . . . . . . . . . Decorative Edging . . . . . . . . . . . . . . . . . . . . . 22 Yoke Assembly . . . . . . . . . . . . . . . . . . . . . . . 7 Cable Assemblies . . . . . . . . . . . . . . . . . . . . . . 8 Spindle Decorating . . . . . . . . . . . . . . . . . . . 23 Recommended Accessories . . . . . . . . . . . . . . . 25 Instaliing the Router . . . . . . . . . . . . . . . . . . . 9 26 Installation of the Counterweight . . . . . . . . . 1 ! Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page: 4

ntroduchon Thank : you for - the purchase of your , Router and more enjoyable operatiOn later , Recreator we think 0neof the most exciting and " tart b " ' - : ' - " " ; " " - _ , : _ , _ , _ _ _ L _ _ . . , : _ : n . _ i " " : " r _ _ y cnect _ ng anQ accoun [ ng mr all the loose creaEivetuon _ w G , , ) llle . alU g H yed = . - - arts If an - art " ; " " ; " " : . . . . . . . . . : p . yp s are missing cnecK me car _ on once In order tofaclitate ; handlingand . minimiZe any more , then contact your local Sears Retail or damage that might occur during shipment your new Catalog outlet for replacement . Recreator s packaged un - assembled We know Th • . . T . . . . . : " " t J - b t e model number or your Recreator ( 113 251890 ) youreanxloustoseewnatyournew _ oolwtl oo u an - " th . . . . . . . . . . . . . . . . . . ' - . . . . n : w areful readn the u upar _ numDeroTmemlssmgpar _ wi Devery a Tew minutes spe t no , c y g het - fu n . . . . . . . . . . . . . fo low ng instructions , wi 1 result in less frustration p s _ € ; ur _ ng _ ne replacemem part . unpacking and checking contents QTY . ITEM DESCRIPTION A Corner Brackets . . . . . . . . . . . . . . . . . . . . . . . . 2 A 8 C _ , D E B Track Brackets . . . . . . . . . . . . . . . . . . . . . . . . . 2 h A , _ | * C Pulley Cover Guards . . . . . . . . . . . . . . . . . . . 2 1 _ t Y / 7 _ _ E She f Boards . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ii / i _ iii . _ j _ 2 P . c - - _ , _ ' _ " _ % X G 1 / 16 ' styIUSRR _ d . . . . . . . . . . . . . . . . . . . . . . . 11 Sii _ _ _ J Yoke Assembly . . . . . . . . . . : . . . . . . . . . . . . . . _ i _ r = _ I i _ t K Shaft . . . . . . . . . . . . . . . . . . ; . . . . . . . . . . . . . . . 1 N ' _ V _ K J _ \ _ L Pulleys ( 5 " ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 L K H \ G F M Counterweight Shaft . . . . . . . . . . . . . . . . . . . . N Counterweight . . . . . . . . . . . . . . . . . . . . . . . . . 1 ITEM DESCRIPTION QTY . P Shaft Lock Brackets . . . . . . . . . . . . . . . . . . . . 2 Q Loose Parts Bags . . . . . . . . . . . . . . . . . . . . . . . 2 Collar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Bag . No , 76008 contains the following : Screw , Soc . Set 1 / 4 - 20 x 1 / 4 . . . . . . . . . . . . . 4 Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Nut . Hex 8 - 32 . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Spindle Center Screw . . . . . . . . . . . . . . . . . . . . 2 Washer 3 / 16 x 3 / 8 x 1 / 32 . . . . . . . . . . . . . . . 2 Stylus Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Screw , Seres Pan Hd , 10 - 32 x 3 / 4 . . . . . . 2 Large Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Lockwasher _ External 1 / 4 . . . . . . . . . . . . . . 2 Small Knob . . . ; . . . . . . . . . . . . . . . . . . . . . . . . 1 Screw , Soc . Set 5 / 16 - 18 x 5 / 16 . . . . . . . . . . 1 3 / 4 " Stylus Collar . . . . . . . . . . . . . . . . . . . . . . 1 Screw . Hex Hd 3 / 8 - 16 × 1 - 1 / 2 . . . . . . . . . . 2 Stylus Grip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I Washer . 3 / 8 x 7 / 8 x 5 / 64 . . . . . . . . . . . . . . . . 2 Nut . Hex Jam 3 / 8 - 16 . . . . . . . . . . . . . . . . . . . . 6 Bag NO . 76018 contains the _ otlowing : Screw . Pan , Hd . t / 4 - 20 x1 - 1 / , _ . . . . . . . . . . : 20 Wrench . Hex " L " t / 8 . . . . . . . . . . . . . . . . . . . . 1 Wrench , Hex " L " 5 / 32 . . . . . . . . . . . . . . . . . . 1 Screw Pan Hd t / 4 - 20 x 1 / 2 . . . . . . . . . . . 18 Nut , Hex 1 / 4 - 20 . . . . . . . . . . . . . . . . . . _ 32 Screw , Rd . Hd . 1 / 4 - 20 x 2 - 1 / 2 . . . . . . . . . . . 1 Screw , Pan lid 10 - 32 x 1 / 2 . . . . . . . . . . . . . . 3 Wing Nut . 1 / 4 - 20 . . . . . . . . . . . . . . . . . . . . . . . 2 getting to know your router - recreator COUNTER YOKE ASSEMBLY WEIGHT TILT PLATE ROUTER MOUNT / We'll be referring to the various parts of the Router Recreator by name throughout this manual • It will be helpful if you study the following drawing and familiarize yourself with the major components , Periodic referral to this section will also be helpful if you become puzzled while reading some of the more detailed instructions . l FRONT CORNER SHELF BOARD . BRACKET INNER PULLEY COVER " : - : SHELF BOARDS _ GUARDS i CORNER TRACK BRACKET " 4
Page: 5

assembly THE FOLLOWING TOOLS WiLL BE REQUIRED FOR ASSEMBLY AND ALIGNMENT 1 / 8 " 5 / 32 " Socket head Pliers setscrew wrenches 9 / 16 " wrench 5 / 8 " wrench 7 / 16 " wrench ( supplied ) 3 / 8 " wrench Combination Square Tape measure Screw driver - - medium I . BASE ASSEMBLY Working in a welt lit , clean area is always a plus . It's also a good idea to place all hardware ( nuts and bolts ) in a bowl or other suitable container so they're C easily accessible and don't get scattered . FOR THIS FIRST OPERATION YOU'LL NEED : ITEM DESCRIPTION QTY . A Shelf Brackets . . . . . . . . . . . . . . . . . . . . . . . . 6 B Corner Brackets . . . . . . . . . . . . . . . . . . . . . . . 2 C Track Brackets . . . . . . . . . . . . . . . . . . . . . . . . 2 D D Pan Head Screws , 1 / 4 - 20 x 1 - 1 / 4 " . . . . . . 12 E Shelf Boards . . . . . . . . . . . . . . . . . . . . . . . . . . 3 F Pan Head Screws , 1 / 4 - 20 x 1 / 2 " . . . . . . . . 8 G Hex Nuts , 1 / 4 x 20 . . . . . . . . . . . . . . . . . . . . . 20 TRACK BRACKET 1 - 1 / 4 " PAN j HEAD SCREW © © NOTE : The base of your Router Recreator is made up of 2 Shelf Boards ( front and rear ) , 2 Track Brackets ( top ) , and 2 Corner Brackets ( bottom ) see illustration . Attach all Brackets to the Shelf Boards as shown SHELF using a 1 - 1 / 4 inch pan head screw . BRACKET Use a 1 / 2 inch pan head screw to attach the Track and Corner Brackets to the Shelf Brackets ( see illustration ) . H1 / 2 ' PAN 1 EAD SCREW CORNER BRACKET
Page: 6

CHECK FOR SQUARENESS OFG : CORNERS BEFORE TIGHTENIN When assembling the above pieces do not tighten the screws until you have checked all four cornerS of the assembly with your square . \ Instafl a third Shelf Board horizontally us _ ngthe last two holes in the : top of each Track Bracket , The Shelf Brackets should be on the underside of the Shelf and sus pended from the Track Brackets by four 1 - 1 / 4 inch Pan head screws and four Hex nuts as shown . Before tightening the screws check the distance from the edge of the horizontal She { f Board to the front Shelf Board as shown . The distance shouEd be equal when measured at both the left and rig ht side of the frame assembly , You should have one shelf board , two she If brac kets and their related hardware remaining . Thisshelf will be installed later , after you determine what type of work will be done . 6 ¸
Page: 7

D l ! . YOKE ASSEMBLY Step two will require the following parts : ITEM DESCRJPT | ON QTY , A 5 " Pulleys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 B Pulley Shaft Collars . . . . . . . . . . . . . . . . . . . 2 C Socket Head Setscrews , I / 4 - 20 x t / 4 " . . 2 D Pulley Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 E Yoke Sub - Assembly . . . . . . . . . . . . . . . . . . . 1 F Counterweight Shaft . . . . . . . . . . . . . . . . . . . 1 G Pan Head Screws , 10 - 32 x 3 / 4 " . . . . . . . . . 2 H Stylus Mount . . . . . . . . . . . . . . . . . . . . . . . . . . 1 J Large Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 K Small Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . ! L Socket Head Setscrew , 5 / 16 - 18 x t / 4 " . . 1 YOKE ASSEMBLY Place the Counterweight Shaft inside the rear of the Yoke with the bent section of the Shaft extending out and upward . The two holes in the Shaft should align with the two small holes in the Yoke as shown . Secure it with the two 3 / 4 inch pan head screws , / ROUTER MOUNT COUNTER WEIGHT YOKE SHAFT BEARING STYLUS MOUNT Screw the large and small Knobs and a 1 / 4 inch setscrew into the Stylus Mount as shown . Slide this assembly on to the Router Mount Shaft as shown and lightly tighten the setscrew . STYLUS MOUNT SETSCREW
Page: 8

de the Pulley shaft through the bearings at the . rear of the Y0ke Assembly followed by the shaft Collars _ one or1 each side of the Yoke as shown , install 1 / 4 inchsetsCrew in thethreaded h01e in each of the Collars . The Collars should not be at this time . SHAFT SHOULD EXTEND BEYOND PULLEYS APPROXIMATELY 1 / 8 " PULLEY HUB Slide the 5 inch Track Pulleys o n to the Pulley Shaft with the hub of the pulley ( area which contains the / setscrew ) facing toward the Yoke as shown . This / Shaft shoulc _ extend beyond the Pulleys approximately 1 / 8 inch on each end . ON EACH END Place the pulley hubs on the Shaft such that one pulley set screw faces front while the other faces rear as Shown . This wil ! help insure access to one of the set screws during future adjustments . PlaCe the entire yoke assembly on the frame with the pulleys riding on the Track Brackets and the large black Knob facing the front . Loosen the pulley setscrews and push outward on the pulley so that the tracks are riding on the inside corners of the pulley grooves as shown . Tighten thed pulley setscrews . The Pulley Shaft should exten beyond the faces of the pulleysan equal amount on each side , TRACK MUST RIDE ON INSIDE EDGEOOVE OF PULLEY GR A Iii . CABLE ASSEMBLIES For step three you'll need - - 0 ) ) ) ) ) ) l ) ) ) } ) } ) - - ITEM DESCRIPTION QTY : A Steel Cables . . . . . . . . . . . . . . . . . . . . . . . . . . 2 B 8 - 32 Hex Nuts . . . . . . . . . . . . . . . . . . . . . 2 C 3 / t6 X 3 / 8 Flat Washers . . . . . . . . . . . . . . . 2
Page: 9

Place the threaded end of one cable through the small hole in the tab at the front end of the pulley track as shown . Wrap the cable one time around the pulley and then push it through the hole in the tab at the rear of the track . While applying slight tension on the cable , with thebyas aid of pliers , install the 3 / 8 inch washer followedble the 8 - 32 Hex Nut on the threaded end of the ca shown . Repeat the cable installation on the other pulley . Check for free movement of the pulleys . The pulleys should not sJide on the tracks but roll freely without any cable slippage . If additional cable tension is needed , tighten the 8 / 32 Hex nut securing the cable at the rear , while holding the body of the threaded end with a pliers . NOTE : The tension on the two cables should be about equal . Check the tension on each by " picking " the cable like a guitar string and listening to the sound . Adjust the tension to make the two sounds similar in pitch . iV . INSTALLING THE ROUTER ( not supplied ) Step four requires the following : E QTY . ITEM DESCRIPTION A Router ( motor assembly ) . . . . . . . . . . . . . . 1 B Router clamp , . . . . . . . . . . . . . . . . . . . . . . . . 1 C 1 / 4 - 20 x 1 - 1 / 4 pan head screws . . . . . . . . 4 D 1 / 4 - 20 x t - 1 / 2 round head screws . . . . . . 1 E 1 / 4 - 20 Hex nut . . . . . . . . . . . . . . . . . . . . . . . . 1 Your Router Recreator is designed to accept most routers with a motor body from 3 inches to 3 - 3 / 4 inches in diameter . If your router does not easily adapt to the router mount , it is not recommended that you attempt any alteration of the mount or your router .
Page: 10

assembly It may be necessary to consult the owners ' manual which accompanied your router for assistance in removing the router from it's base . Slip the motor assembly into the hole formed by the clamp and router mount , Place any protrusions SLiCh as elevation gear racks in the recess in the Router Mount or in the gap between the Router Mount and Clamp . Tighten the four pan head sc rews . If your router has a built - in work light or switch wired throug h the handle , the steps below should be ROUTER \ followed to secure both miter base and motor : \ _ iBASE ! . Remove the base of the router from the motor . [ Usually done by loosening the setscrew * located near the ] ogo plate ) . Loosen anyclamps securing router to router base . * NOTE : When the router is removed from the Router Recreator , remember to tighten thehe set screw into the base until it touches t hoosing ; then back the set screw out half - a - turn . CLAMP BASE 2 . Leave both hand es ntact , and securely mount the motorofthe router between the router clamps MOUNTING as described previously . 3 . Place the router base on top ofthe yoke ; sub - base side down . ( WIRED 4 . Align the holes in the yoke with the three ( 3 ) holes in the router sub - base . Check that the router is located with the switch ( in the handle ) facing towards the operator for easy access . SHAFT SWITCH ( IN HANDLE ) LOCK x 1 / 2 SELF - THREADING 5 . Locate three ( 3 ) 10 - 32 x 1 ! 2 - inch self - threading screws from the loose parts bag . 6 . Insert and thread the three screws in the router sub - base and yoke holes . Tighten with a screwdriver . 10 i . . i . ii . i : ! i
Page: 11

A V . iNSTALLATiON OF THE COUNTERWEIGHT Needed for step five i ITEM DESCRIPTION QTY , A Counterweight . . . . . . . . . . . . . . . . . . . . . . . . 1 B Cord Hook . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Screw the Cord Hook into the Counterweight about 2 or 3 turns , Slide the Counterweight onto the Counterweight shaft , Move the Counterweight on the shaft compensating the weight of the motor , yoke assembly , and routerk base if mounted on yoke . When the router chuc rests lightly on the edge of the front shelf board , secure the Counterweight on the shaft by turning the Cord Hook until it seats against the shaft . \ Pass the motor power cord through the Cord Hook and route toward the rear of the Recreator .
Page: 12

. ' H Vl . INSTALLING THE PULLEY GUARDS Parts required - - 2 ea Pulley Guards Loosen the 1 / 4 - 20 x 1 - 1 / 4 inch pan head screw located at the top of each corner of the frame assembly . Remove the 1 / 4 - 20 x 1 / 2 inch pan head screw and 1 / 4 - 20 Hex nut from the top of each corner of the frame assembly . Place the pulley cover over the pulley and align the slot at the front of the guard with the 1 - 1 / 4 inch pan head screw and re - install the 1 / 2 inch pan head screw through the holes in the side of the guard . then through the Corner Track Brackets . Tighten = the four pan head screws . Repeat the pulley guard installation with the remaining guard . Run the pulley and yoke assembly back and forth to make sure that the pulleys do not drag on the insidehe of the covers . It may be necessary to loosen t / screws and shift the covers slightly to clear the LOOSEN pulleys . VII . MOUNTING YOUR ROUTER RECREATOR TO A STAND To insure safe accurate operation it is important that the frame of your Router Recreator is fastened to a suitable table or leg set . if you fashion your own leg set , remember tot provide access to center of the unit and sufficien clearance of the corner brackets for the positioning of the shelf boards . FRONT NOTE : The recommended ieg set for the router STIFFENER recreator is catalog no . 9 - 22238 . NOTE : See page 2 & 3 of instructions for catalog no . 9 - 22238 leg set and assemble the legs according to trle section headed " For Bases Measuring 24 " x 27 " . " ATTACH SIDE STIFFENERS IMPORTANT : You must attach the side stiffeners to TO OUTSIDE FACES OF THE LEG the outside faces of the legs as shown m this illustration . 12
Page: 13

alignment ALIGNING YOUR ROUTER RECREATOR Proper alignment of your Router Recreator isr essential for accurate results . Although you Recreator is designed to maintain its ' alignment , it is suggested that you check the pulley tracking and Router / Stylus alignment not only before beginningelf . a project , but'occasionally during the project its Remove the two Stylus Rods from the ioose parts bag , Place the 1 / 4 inch end of one of the Stylus Rods in the chuck of the router , Snug the Stylus in place with the Router Chuck Wrench ( supplied with Router ) . Place the second Stylus in the Stylus Mount . This is done by backing off on the small black knob and then re - tightening when the stytus is in place . @ @ Loosen the two Tilt Plate wing nuts which will allow the Stylus / Router Mount to pivot . Roll the Yoke Assembly forward on the Tracks and position the Stylus located in the Routerchuck flush against the front face of front Shelf Board with the chuck face resting on the edge of the shelf . Tighten both Tilt Plate wing nuts . t3
Page: 14

alignment Slide the Yoke Assembly either left or right on the p u [ tey Shaft u ntit the Stylus in the route r centers on the - righthand Set _ afholes in the front Shelf Board . / / While holding the router Stylus Rod in place , ( centeriine of righthand holes ) loosen the Stylus MoUnt sets _ crews and slide the mount left or r ght untd the secdnd Stylus aligns with the lefthand set of h 01es . / " j j / J 0 / If both of the Stylus Rods are not flush with the face of the front Shelf Board atthe sametime , the pulleys _ J require adjustment . STYLUS TO BE CENTERED ON HOLES AND FLUSH AGAINST SHELF FACE Reaching under either one of the pulley cover guards with the 5 / 32 setscrew wrench locate the setscrew and loosen it sufficiently to allow the put ey to rotate independent of the pulley shaft , Note ! Adjustment of only one pulley is necessary , either the left or the r ght pulley may be adjusted . Rol ! the = Yoke Assembly back and forth on the Tracks several times . This should bring the two pulleys into unison . Check to determine if the correction was made by again placing the Stylus Rods aganst the front Shelf Board . If some mis - aiignment is sti detected it may be necessary to gently roll the rig3thand pulley forward while sirfiultaneOusfy rolling the lefthand pulley rearward . If this worsens the rots - alignment reverse the procedure . Once the two Stylus are flush and properly spaced ( centered on hotes ) tighten the _ ) utley and Stylus Mo [ mt setscrews securely . Make sure that the Tracks are again riding on the inside edge of the puJley grooves when making any pulley adjustments . I ! ! ! Finally check for free movement of the Yoke Assembly on the Tracks . If the pulleys slip on the Tracks additional cable tenston may be required . This is done by tightening the 8 / 32 nut at the rear of the Cable Assembly . tf the pulley seems to bind on the Tracks the Cables / may be excessively tight or the pulleys may not be riding on the inside edge of the pulley groove , if necessary , adjust accordingly . If the Yoke Assembly does not slide freely from side to side . : lubrication of the pulley shaft may be required . Silicon spray or graphite provi0e excellent | egricat On and wil ! not attract sawdust . If the : yoke assembly does not slide freely after lubrication ; the . bearings may be slightly misaligned . Rap : the yoke Sharply above the bear rigs with _ he beet of the hand torealign the bearings . / /
Page: 15

operation GENERAL OPERATING HINTS 1 . Most projects undertaken with the Router 4 . The wing nuts on the tilt plate may be loosened Recreator will require some time to complete . which allows you to orient the stylus and bit to Make sure when you begin your work that you perform some relief work although most work are comfortable . Although your Recreator can will be done with the bit and stylus be operated from a standing position you'll find perpendicular to the piece . These wing nuts a chair will be helpful , should be tightened after the desired angle is obtained . 2 . It is recommendedthatyourwork begin with the 5 , When operating your Recreator place the left largest router bits and step down in bit diameter hand on thesmall knob ( stylus mount knob ) and as the work progresses . The smaller the bit the right hand on the large knob . It is less tiring if diameter the greater the detail . ALWAYS MAKEY you rest your forearms or wrist on one of the SURE THE STYLUS DIAMETER PRECISEL nearby shelf boards while maneuvering the MATCHES THE DIAMETER OF THE BIT stylus and bit . SELECTED . For stylus diameters greater than i / 4 ' , a 3 / 4 stylus collar is provided . Secure itto 6 . For very fine detail work , it may be more the 1 / 4 " end of a stylus with the setscrewthe convenient to attach the stylus grip ( provided ) wrench . The sleeve should be flush with to the stylus and guide the stylus with the fingers bottom of the stylus tip . of either hand on the stylus grip . The stylus grip should be between the small end of the stylus and the small knob . 1 / 8 " ROD END - " _ ' " _ 1 / 16 " ROD END 7 . When excessive stock must be removed don't 2 overwork your router or Router Recreator _ STYLUS Several successive shallow cuts witi produce RODS better results than a few deep cuts and prolong the life of your tool and bits . IL . . . 1 / 4 ' RODEND 8 . To produce straight tine movement ( front to rear ) lock the yoke assembly in place with the 3 / 4 " SLEEVE - - _ _ - STYLUS GRBP aid of the shaft lock collars . 9 . TO produce straight line cuts left to right use the STYLUS TgP RECOMMENDED ROUTER BIT shaft lock brackets . t0 . Always keep in mind the direction of rotation of 3 / 4 " sleeve . . . . . . . . . 3 / 4 " straight face 9 - 2255291 the router bit ( clockwise when viewed from 1 / 4 " rod end . . . . . . . . 1 / 4 " straight face 9 - 255 above ) and always move the router bit into the 1 / 8 " rod end . . . . . . . . . 1 / 8 " straight face 9 - 2552 workplace so that the cutting edge of the bit is 1 / 16 " rod end . . . . . . 1 / 16 " straight face 9 - 9255289 or 1 / 16 " double ended 9 - 255 chopping into the work and not gouging out . This will help prevent splintering of the 3 . Before beginning your work check for the workplace , tearing out large sections , or proper relationship of the router bit to the stylus kickback . Never turn the router on with bit in in respect to elevation . The easiest way to check contact with the workpiece , for proper cutting depth is to rest the router bit 11 . If the bit begins to scorch the wood as it cuts this on the tedge of the front shelf board then loosen usually indicates that resin ; gum or pitch has the stylus mount knob ( small knob ) and allow accummulated on the cutting edge or that the the stylus to also rest on the shelf edge . bit is dull , Remove any gum or pitch with " Sears It is possible to set the stylus above or below the Gum and Pitch Remover " or sharpen and dress the cutting edge with a ftat oil stoneto regain the router bits , and some operations which are discussed later will require this , sharp edge . As you become more familiar with your Router plaques . It can turn a simpte piece of rectangular or round stock into a handsomely decorated spindle . Recreator you will begin to realize its versatility . In addition to its primary function of a three The following pages wilt instruct you in the proper dimensional duplicator , it also does an excellent job mounting and operating techniques for all of the of reproducing signs from an existing sign or above operations . drawing , it is capable of carving two dimensional 15
Page: 16

MOUNT VERTICALLY { VARIOUS SPACINGS ) MOUNT ON TOP \ OF SHELF BRACKET MOUNT DIRECTLY TO CORNER BRACKET MOUNT TO BOTTOMT OF SHELFBRACKE THREE DIMENSIONAL CARVING When Ca _ ' ving three dimensional objects bear in mind that the capacities of your Recreator will limit 8 _ you to an object not more than 8 inches in diameter 8 _ _ = , . and 8 inches taif . Measure the master to make sure it is within these limits before proceeding . , i Unless a - single block of wood large enough to contain the entire carving is : available , it ; will be necessary to laminate several : pieces of 3 / 4 inch stock to the size required . ' . = An interesting effect can be achieVed by laminating woods of contrasting colors such as redwood and white pine , For your initial attempts , however , an all redwood or pine workpiece isrecommended . , , , , , i After the laminated workpiece has dried , removeor any excess stock with a sabre saw . band saw coping saw . Try to remove as much excess stock as possible but make sure the workpiece remains larger than the silhouette of the master . \ BROWN KRAFT PAPER " 16
Page: 17

The two work mounts will be required for 3 dimensional carving . The master and workplace can be attached to the work mounts by either wood screws or carpenters glue and must be mounted on the same side of the work mount as the threaded T nut . By drilling pilot holes in the work mount the master and workplace can be secured with 1 - 3 / 4he inch wood screws . Make sure the heads of t screws are counter - sunk to prevent any interference . When screwing the object to the work mount is not possible or desirable , carpenters wood glue wi ! la bond most wood or ceramic type objects . Spread liberal amount of glue on the work mount . Cut a piece of Brown Kraft paper ( shopping bag paper ) . Place it on the work mount and apply glue to ther . paper , Place the master or workpiece on the pape Allow to dry per directions specified with glue . i . . . . J \ This process will hold the objects securely to theno work mounts yet allow easy removal with damage to the master or duplf . cate . To remove the objects all that will be necessary will be to place a sharp chisel or screwdriver between the object andur work mount and rap sharply with the palm of yo hand . When gluing or screwing the objects to the hworke mounts , make sure that they are oriented in t same direction , in respect to the work mount , for thes sides of the work mount will be used as reference when rotating . Secure the master and the workpiece to the front . . . . . . . . . . . shelf board by screwing the 1 - 1 / 2 inch Hex head bolts and washers through t _ e front of the shelfin board and then intothethreaded " T " nut centered the work mount , Align the work mounts by placing a straight edgend along the top edges of both the master a workpiece work mounts , When the work mounts touch the straight edge at all points tighten the 3 / 8 bolt in each mount . Insta { t a 3 / 4 inch router bit and a matching stylus . Set the depth of the stylus to the same height as the bit by using the edge of the front shelf as a guide . ] 7
Page: 18

operation With adequate eye protection in place , plug , rtheol router motor in . While holding one of the Contce knobs to insure that the bit is free of the workpie turn the switch on . Using two hands , one on the large knob the second on the small black knob , gently stroke the router bit into the workpiece . The / " stylus will guide from the master and the profile of the master will soon begin to appear in the workpiece . After sufficient material has been removed from the starting position , turn the router off , loosen the 3 / 8g bolt and rotate both work mounts 90 ° aga } n alignin with a straight edge . Repeat the above on all four edges of the work mount . After the workpiece has been rotated 360 ° remove the large bit and step down to the next smallest . . . . . diameter bit and repeat the above process . Always re - set the elevation of the stylus in respect to the bit _ - _ z , when changing bits . \ BINATION SQUARE Some intricate carvings may require a i45 ° d / orientation . This can be accomplished with the a \ of a combination square . \ Note ! When carving objects which are symmetrical , it may become difficult to tell front from rear . You may Wish to identify the starting edge of both work mounts to keep them in proper relation . \ - % \ \ \
Page: 19

TILT PLATE WING NUTS As the carving begins to take shape some undercut work may be necessary . This can be accomplished by loosening two wing nuts near the yoke tilt plate , titting the yoke assembly to the desired angle and then re - tightening the wing nuts . " Always turn theny router off when pivoting the yoke or making a adjustment , " After the object is nearing completion you may find it necessary to re - mount the master and workpiecewitl in a vertical plane rather than horizontal . This allow the bit to contact the workpiece on the top and base sections of the carving that were inaccessible in the horizontal plane . { 3 © 0 © \ After the object has been completely carved it can be finished in a number of ways , Some prefer the rustic hand carved appearance that results from the router bits while others prefer sanding by hand or with a small hobby too [ . ! 9
Page: 20

ii " n operatlo / / After the desired finish s achieved , additional detail can ' be addedw th hand sculpturing tools ora small engraving tool . Remove : the workpiece and master from the work mount and if glued , any residue can be removednd from : the work mounts or workpieces with sa paper , SIGN MAKING LEFT HAND Signs can be duplicated from originals lorl SHAFT COLLAR reproduced from a drawing . The Recreator wi carve signs upto 10 inches wide and 24 inches long or even longer if there is sufficient room for the s _ gn to overhang the fro nt and rear shelf boards . Place the two inner shelf boards between the front and rear shelf boards with their surfaces flush tothe top edge of the front and rear shelf board . Secure the two inner shelf boards with the shelf brackets , pan head screws and nuts . Using a piece Of plywood , masonite or particle board larger then the drawing , tape the drawing Of the sign to this back - up board . Select a workpiece cut to the desired final size of the sign . Redwood is an excellent and relatively inexpensive material to use for sign making . \ Mow nt the master and its hardboard backing on the \ left side of the Recreator and align the m aster to the tracking of the Recreator by tracing the edge of the sign with the stylus in the stylus mount . With the \ stylus in contact with the edge of the sign , move one of the shaft collars into contact with the yoke bearing face . Tighten the set screw in this cellar etol . limit the stylus to straight line front to rear trav the workpiece at all points while the stylus is When the edge of the sign follows the travel of the following the line indicating the top of the sign on stylus as it moves from front to rear . secure the . the drawing . C - clamp the workpiece when the master to the inner shelf boards with C - clampsere master and workpiece are parallel . Again , use Position the C - clamps on t he back up board wh caution when C - clamping the work piece to prevent they will not interfere with the free movement of the the bit from striking the C - clamp . yoke assembly . Move the sty lus to the bottom line of the sign on the Mount the workpiece to the right of the master and drawing ; The router bit should also be touching the using a t / 4 inch router bit in the same fashion asthe bottom edge of the workpiece . Move the right hand stylus was used , alignthe workpiece tothe master atoof shaft collar against the yoke bearing and lock it with front and rearlMovetheyoke assembly from front t the setsc few wrench , rear making sure the router bit touches the edge 2O
Page: 21

SHAFT LOCK tn addition to the shaft lock collars , shaft lock COLLARS brackets are also provided . These can be slipped under the outside tip of the pulley cover guards and the hole in t : he bracket placed on the pulley shaft . The opposite end of the bracket which is slotted can be screwed to the corner track bracket with a 1 / 2 inch pan head screw , Iockwasher , and wing nut These shaft lock brackets will immobilize the pulley sh aft and only permit the yoke assem bly to travel left to right or right to left . This is an excellent way stoe produce straight line cuts from side to side . The brackets are also helpful in securing your Router Recreator when transporting . After aligning the master and the workpiece , a router bit and matching stylus suited for ethet . application should be selected and the elevation s If working from a drawing determine whether thent _ etters are to be raised or recessed , and the amou of recess or desired height of the letters . If a raised Ietter is desired , raise the stylus above the drawing the same height as the desired height of the letters . A small scale or ruler is helpful in determining thers depth of cut . Route all areas around the lette leaving the letter intact , Smaller diameter bits and stylus may be required for the detailing of more intricate lettering , If recessed letters are desirable , simply trace ethen letters with the stylus after the depth of cut has be selected . When duplicating a sign from an existing sign the RAISED J LETTERS elevation of the stylus and bit should be the same . If the sign requires some relief cutting or slight RECESSED LETTERS undercuts , this can be accomplished by loosening F / / the tilt plate wing nuts , pivoting the yoke assembly to the desired angle , and the resecuring the two wing nuts . 21
Page: 22

i operat on iATIVE EDGING A molded or decorative - edge can be added to most rectangular shaped pieces of stock with your " Recreator , a decorative edging bit and the router work arbor set ; i : Set the two inner shelf boards as prescribed for sign making , Check : for parallelism between the Recreator randk the workpiece by us ng the pilot section of the wo arbor . A . Touch the pilot to the edge of the workpiece at the front of the Recreator . B . - C - clamp the work _ ) iece to the shelf board and set both left and right hand shaft collars . C . Move the yoke assembly to the rear . Shift theot rear of the workpiece until it also strikes the pil \ section of the work arbor . C - clamp the rear of WORK ARBOR the workpiece to the shelf board . PILOT D . The depth of cut will be controlled by thestylus riding on the back up board located on the left of the Recreator . You will note that variations in the molding can be obtained by altering the depth of cut or by setting the workpiece slightly away from the pilot of the work arbor . Shaping cross grain can also be accomplished with OLE IN SHAFT BRACKET the aid of the shaft lock brackets . LACED OVER END OF PULLEY SHAFT
Page: 23

SPINDLE DECORATnNG Your Recreator is also capable of adding decorative rings , or axial veins and grooves on spindles up to 24 inches long _ These decorative cuts can be made from a drawing template or an existing turning , Some exact duplicates of original turnings may not be possible because of the contours that are available from router bits , MOUNTING THE SPINDLE This operation will require - - 1 ca . Work Mount 1 ca . 3 / 8 - ! 6 x 1 - 1 / 2 inch Hex head bolt 1 ca . cone point spindle mount 3 ca . 3 / 8 " - 16 Hex Jam nuts . 1 ca . 3 / 8 x 7 / 8 x 5 / 64 inch washer Locate the center of each end of the spindle and make an impression with a hammer and punch . Cut a piece of brown kraft paper ( paper bag ) the sizehe of the work mount and cut a hole in the center of t • f paper over the T nut , Screw the cone point spindle mount through the work mount allowing the cone point to protrude above the face of the work mount T nut . Take the brown paper , coat both sides with carpenters glue and lay it on the work mount . With the paper in place , lay the work mount on the end ofa the spindle . Using the cone point spindle mount as centering point , align it with the impression previously made in the center of the spindle . Carefully back the cone point spindle mount awayIf from the workpiece and allow these pieces to dry . done correctly this will center the spindle on the work mount . Remove the two inner shelf boards and re - install one of them vertically spacing it away fromthe front SHELF BOARDS SPACED LENGTH shelf board the length of the spindle plus 1 - 3 / 4 inch . = F SPINDLE PLUS Screw one 3 / 8 " nut on the cone point spindle mount . Place the spindle mount through the top right hand hole of the center shelf board . Install a second 3 / 8 " nut on the end of the cone point spindle mount protruding through the shelf board . HEX NUTS Place a 1 _ 1 / 2 inch Hex head bolt through the topit HEX HEAD rig ht ha nd hole of the front shelf board and secure BOLT with a flat washer and nut , Take the spindle and work mount , after it haslt sufficiently dried , and screw it on the Hex head bo " WASHER located in the front shelf board , & NUT WORK MOUNT While holding the spindle in place screw the cone i I point spindle mount until it engages the impression in the spindle center . \ CONE POINT To secure the spindle : SPINDLE MOUNT A . Spin the inside hex nut on the cone point spindle mount until it strikes the shelf board . B , Tighten the hex nut on at the front shelf board until it is snug against the work mount . C , Tighten the hex nut on the back side of the cone point spindle mount to prevent it from rotating , 23
Page: 24

Jld now be pbsSible to rotate the workpiece by L9 / 16 wrench on theHex head bolt located center wobble should be etectable . If the spindle : is not secure in its mounting do not attempt to operate until the necessary adjustments have been made . Mount the sketch on the back up board which is installed on the left side of the Recreator . Install a 1 / 4 inch stylus in the stylus mount . Select a bit desired for the first cut and secure it in the router chuck . f ROTATE t " COUNTER CLOCKWISE Move the yoke assembly on the pulley shaft until the f / bit is approximately 1 / 4 inch off the centertine of the / / spindle to the left . Lock the right hand putley shaft collar against the yoke bearing to serve as a stop , Rest the router bit on the spindle and check for perpendicularity . If adjustments are required loosen Holding the stylus tip in contact with the back - up the tilt plate wing nuts and square as necessary . board during the operation , tu rn the router on . lusinge a 9 / 16 box end wrench , Begin rotating the spind Re - tighten the tilt plate wing nuts . " counter clockwise " s _ multaneousty start moving Move the bit to the area of the first cut as determined the bit into the s pindle until it stops against the right by the drawing or template and lock the pulley shaft hand shaft collar . at that location with the pulley shaft locks and wing n uts . After the cut is completed ( usually several revolutions of the spindle ) , back the bit away from Set the depth of cut by raising the stylus above the the spindle and turn the router off . back up board the desired amount . Move to the next desired location and repeat above Move the router bit tothe left of the spindle making procedure . sure it is clear of the spindle . To create axia cuts , those running along the length of the spindle mount the spind e as indk _ ated above then : Move the router bit to the centerline of thespindte and lock the yoke at this setting by securing both left hand and right hand shaft collars . Set the depth of cut usi ng the stylus and the back up board as a guide . C - clamp the work mount to the front shelf board to prevent _ t from rotating . J Liftthe bit clear of the spindle , turn tt _ e router on and lower the bit into the spindle . / jjj i L Move the yoke assembly back and forth until thecut C - CLAMP WORK MOUNT _ is € ompleted , Veins deeper than 1 / 8 of an inch TO PREVENT ROTATION O should be made in successive cuts of 1 / 8 inch .
Page: 25

recommended accessories ITEM CAT . NO . Leg Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 22238 Recreator Bit Assortment . . . . . . . . . . . . . . . . 9 - 2t 216 Casters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 22208 Face Shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 18613 Portable Electric Tool Handbook . . . . . . . . . . 9 - 2949 The above recommended accessories are current and were available at the time this manual was printed , 25
Page: 26

PARTS LIST FOR CRAFTSMAN ROUTER * RECREATOR MODEL NO . 113.251890 " 2 2 4 1 11 12 7 o 23 8 15 0 6 21 0 I 24 21 25 19 5 is 6 _ 26 27 31 25 28 29 30 17 / 42 15 8 39 / I 37 32 - 7 I 32 \ \ 33 o0 / 4s - - @ _ 47 0 j / / 0 J J J J O J J \ O ° 2 ! i : 26
Page: 27

PARTS LIST FOR CRAFTSMAN ROUTER - RECREATOR MODEL NO . 113.251890 Part Part Key Key No . No . No . Description NO . Description - - i , p = , , , , = _ " 28 ' 76003 Mount Asssembly , Router 1 ST D512505 * Screw , Pan Hd , I / 4 - 20 × 1 / 2 29 060371187 176025 * Bolt , Carriage 1 / 4 - 20 x 4 - 1 / 25 23 Cover , Pulley 30 943 * Screw , Hex Hd . 5 / t6 - 18 x 76007 Counterweight 31 76023 * Clamp , Router 4 63221 Hook , Cord 32 76006 Mount Assembly , Workpiece 5 76021 Frame , Shelfelf 33 446364 Washer , 3 / 8 x 7 / 8 x 5 / 64 6 76028 Bracket , Sh 34 ST D5237 ! 5 * Screw , Hex Hd . 3 / 8 - t6 x ! - 1 / 2 7 STD512515 * Screw , Pan Hd . 1 / 4 - 20 x 1 - 1 / 4 35 1760174 Grip , Styluss 8 STD541025 * Nut , Hex 1 / 4 - 20 36 760 Rod , Stylu 1 / 8 9 STD54 ! 008 * Nut , Hex 6 - 32 37 76011 Mount , Stylus 10 STD551008 * Washer , 3 / 16 x 3 / 8 x 1 / 32 38 760 ! 2 Knob , 2 " 11 STD551225 * Lockwasher , External 1 / 4 39 76027 CIip , Speed 12 76009 Cable 40 76002 Plate , Tilt ! 3 76024 Lock , Shaft 4 ! STD541631 * Nut , Wing 5 / 16 - 18 ! 4 STD541625 * Nut , Wing 1 / 4 - 20 42 76013 Knob , I - 1 / 4 ! 5 1760209 Bracket , Trackner 43 STD511107 * Screw , Pan Hal . 10 - 32 x 3 / 4 16 ' 760 Bracket , Cor 44 STD551210 * Lockwasher , No . 10 17 STD503103 * Screw , Set Socket Hd . Cup Pt . 45 760I 6 Collar , Stylus 3 / 4 5 / 16 - 18 x 3 / 8 18 STD328052 ( Includes Set Screw ) Puiley ( includes Set Screw ) 46 76015 Rod , Stylus 1 / 16 19 60372 Collar 47 30505 * Wrench , Hex " L " 1 / 8 20 STD502502 * Screw , Set Socket Hd . 48 37837 * Wrench , Hex " L " 5 / 32 1 / 4 - 20 x t / 4 49 113967 Screw , Rd . Hal . t / 4 - 20 x 2 - 1 / 2 21 STD541237 * Nut , Hex Jam 3 / 8 - 16 5O STD601105 * Screw , Pan Hd . 10 - 32 xl / 2 22 76022 Shaft , Counterweightnter 76008 Bag Assembly , Loose Parts 23 7601026 Screw , Spindle Ce ( Not illustrated ) 24 760 Shaft 76018 Bag Assembly , Loose Parts 25 76001 Bearing , Sleeve ( Not illustrated ) 26 76000 Yoke ( ' Includes Key # 25 ) 76005 Owners Manual ( Not illustrated ) 27 76004 . . . . P . . a . . nel , Trim * Standard Hardware Item May be Purchased Locally 27
Page: 28

ears i ROU'rER - RECREAIOR SERVaCE Now that you have purchased your Router - Recreator , should a need ever exist for repair parts or service , simply contact any Sears Service Center and most Sears , Roebuck and Co . stores . Be sure to provide all pertinent facts when you call or visit . MODEL NO . The model number of your Router - Recreator will be found on a plate attached to the yoke assembly . 113.251890 HOW TO ORDER WHEN ORDERING REPAIR PARTS , ALWAYS GIVE THE FOLLOWING INFORMATION : REPAnR PARTS PART DESCRIPTION PART NUMBER NAME OF 1TEM MODEL NUMBER ROUTER - RECREATOR 113.251890 Ail parts listed may be ordered from any Sears Service Center and most Sears stores . If the parts you need are not stocked locally , your order will be electronically transmitted to a Sears Repair Parts Distribution Center for handling , Sold by SEARS , ROEBUCK AND CO . , Chicago , IL . 60684 U . S . A . Form NO . SP4375 - 2 Printed in U . S . A . 3 / 83 Part No . 76005
Search in Routers on ebay
"