Home | Register Login | Wanted Manuals | MarketPlace | Members Area | Manuals Manufacturer Directory | UPC Lookup | Information Pages | Policy


Back To Craftsman Table Saw       Model: 113.29570 or 11329570 Craftsman 10 Inch Motorized Table Saw
Regular Text Search or Search by Model Number

Register / log-in to add to your Hammerwall Collection.
Manual Location


This is a partial text extraction from the pdf, to download the pdf, click the Manual tab. If you want to search this text, hold control and F, and type the word you are looking for.

Page: 1

ISears ] owners manual MODEL NO . 113.29570 SAW ONLY 113.295750 SAW WITH LEGS AND TWO TABLE EXTENSIONS Serial Number . . . . . . . Model and serial number may be found at the right - hand side of the base . You should record both CRAFTSMAN ° model and serial number in a safe place for future use , IO - INCH MOTORIZED CAUTION : TABLE SAW Read GENERAL and ADDITIONAL • assembly SAF ETY • operating INSTRUCTIONS carefully • repair parts Sold by SEARS , ROEBUCK AND CO . , Chicago , IL 60684 U . S . A . Part No . 62716 Printed in U _ S . A .
Page: 2

FULL ONE YEAR WARRANTY ON CRAFTSMAN TABLE SAWS If within one year from the date of purchase , this Craftsman Table Saw fails due to a defect in material or workmanship , Sears will repair it . free of charge . WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS STORE OR SERVICE CENTER THROUGHOUT THE UNITED STATES , This warranty gives you specific legal rights , and you may also have other rights which vary from state to state , SEARS . ROEBUCK AND CO . . Sears Tower . BSC 41 - 3 . Chicago , ] L 60664 general safety instructions for power tools protectors ( plugs or muffs ] during extended periods of 1 . KNOW YOUR POWER TOOL operation . Read the owner's manual carefull , _ . Learn ts aoDlication and limitations as well as the specific 13 . SECURE WORK potenttal hazards peculiar to this tool Use clamos or a vise to hold work when practical , t's safer than using your hand . frees both hands to operate 2 . GROUND ALL TOOLS tool Th ; tool s equipped with an approved 3 * conductor DON'T OVERREACH coro and a 3 * prong grounding tvoe plug Io fit the 14 . Drouer grounamg [ yDe receptacle . The green conauctot Keep proper footing and balance at all times . ' n me cord _ s the grounding w _ re . Never connect the green wire to a live terminal 15 . MAINTAIN TOOLS WITH CARE Keen tools sharp and clean for oest and safest 3 . KEEP GUARDS IN PLACE performance . Follow instructions for lubricating and n working order , and n proper adjustment and changing accessories alignment . 4 . REMOVE ADJUSTING KEYS 16 . DISCONNECT TOOLS AND WRENCHES before serv = cmg ; when changing accessoHes such as Form habit of checking to see that keys and adjusting blades , bits . cutters etc wrenches are removed from tool before turning it on , 17 . AVOID ACCIDENTAL STARTING 5 . KEEP WORK AREA CLEAN Make sure switch is ' n OFF poston before plugging Cluttered areas and benches mvite accidents . Floor in . must not be slippery clue to wax or sawdust . 18 . USE RECOMMENDED ACCESSORIES 6 . AVOID DANGEROUS ENVIRONMENT Consult the owner's manual for recommended Don't use power tools in damp or wet { ocations or accessories . Follow the instructions that accompany expose them to rain . Keep work area well lighted , the Provide adequate surrounding work space , accessories . The use of improper accessories may Cause hazards . 7 . KEEP CHILDREN AWAY i9 NEVER STAND ON TOOL AII visitors should be kept a safe distance f _ om Work _ . . . . area . benous Injury eou d occur if the to01 is tipped or if the cutting tool is accidentally contacted . 8 . MAKE WORKSHOP KID - PROOF Do not store materials above or near the tool such that - with padlocks , master switches , or by removing it is necessary to stand on the tool to reach them . starter keys . 9 . DON'T FORCE TOOL . . . . 20 , CHECK DAMAGED PARTS It will do the job better and safer at the rate for which Before further use of the tool , a guard or other part that it was designed . is damaged should be carefully checked to ensure that it 10 . USE RIGHT TOOL witl operate properly and perform its intended function . Don't force tool or attachment to do a job it was not Check for alignment of moving parts , binding of moving designed for . parts , breakage of parts , mounting , and any other conditions that may . affect its operation . A guard or 11 . WEAR PROPER APPAREL other part that is damaged should be properly repaired Do not wear loose clothing , gloves , neckties or jewelry or replaced . ( rings , wrist watches ) to get caught in moving parts . Nonslip footwear is recommended . Wear protective 21 . DIRECTION OF FEED . . . . . hair covering to contain long hair . Roll long sleeves Feed work into a blade or cutter against the direction above the elbow of rotation of the blade or cutter only . 12 . USE SAFETY GOGGLES ( Head ProtectiOn ) 22 , NEVER LEAVE TOOL RUNNING Wear Safety goggles ( must comply with ANSI Z87 . 1 ) UNATTENDED at all times . Everyday eyeglasses only have impact Turn power off . Don't leave tool until it comes to a resistant lenses , they are NOT safety glasses . Also , use complete stop . face or dust meal ( if cutting operation is dusty ; and ear
Page: 3

ADDITIONAL SAFETY INSTRUCTIONS FOR TABLE SAWS WARNING : FOR YOUR OWN SAFETY , DO NOT contact the rear of the revolving blade can be OPERATE YOUR SAW UNTIL IT IS COMPLETELY thrown back at the operator at excessive speed . This ASSEMBLED AND INSTALLED ACCORDING TO THE can usually be avoided by keeping the guard and INSTRUCTIONS . . . AND UNTIL YOU HAVE READ spreader n glace for all " THRU - SAWING " AND UNDERSTOOD THE FOLLOWING . operations ( sawing entirely thru the work ) AND by 1 GENERAL SAFETY INSTRUCTIONS FOR POWER remowng all loose pieces from the table with a long stick of wood IMMEDIATELY after they are cut TOOLS . . . SEE PAGE 2 off . 2 . GETTING TO KNOW YOUR SAW . . . SEE PAGE 15 D = Use extra caution when the guard assembly is 3 , BASIC SAW OPERATION . . . SEE PAG E 17 4 , ADJUSTMENTS . . . SEE PAGE 23 removed for resawmg , dadoing , rabbeting , or 5 . MAINTENANCE . . . SEE PAGE 26 molding - - replace the guard as soon as that operation is completed , 6 . STABILITY OF SAW E . NEVER turn the saw " ON " before clearing the If there _ sany tendency for the saw to tio over or move table of all tools , wooa scraos , etc , , except the during certain cutting operations such as cutting workpiece and related feed or support devices _ for extremely large heavy panels or long heavy boards , the the operation planned . sawshould be bolted down . F . NEVER place your face or body in line with the If you attach any kind of table extensions over 24 " cutting tool . wide to either end of the saw , make sure you either G . NEVER place vour fingers or hands in the path of bolt the saw to the bench or floor as appropriate , or the sawblade or other cutting tool . support the outer end of the extension from the bench H . NEVER reach in back of the cutting tool with or floor , as appropriate . either hand to hold down or support the workplace , LOCATION remove wood scraos , or for any other reason . Avoid The saw should be aositioned so neither the ooerator awkward operations and hand positions where a nor a casual observer is forced to stand in hne with the sudden slip could cause fingers or hand to move saw blade . into a sawolade or other cutting tool . 8 . KICKBACKS I . DO NOT perform any operation " FREEHAND ' " Kickbacks can cause serious injury : A " KICKBACK ' " alwa _ , , s use either the np fence or the miter gauge to occurs when a part of the workplece binds between the oosition and guide the work . sawblade and the rip fence or other fixed object , rises J , NEVER use the rip fence when crosscutting or the from the table , and is thrown toward the operator , miter gauge when ripping . DO NOT Jse the rip fence as a length stop . < eeD your face and body to one side of the sawblade , Never hold onto or touch the " free end " of the out of line with a possible " Kickback . ' " workpiece or a " ' free piece * ' that is cut off , while Kickbacks - and possible injury from them can power is " ON " and / or the sawblade is rotating . usually be avoided by : K . Shut " OFF " the saw and disconnect the power cord A , Maintaining the rip fence paragel to the sawblade . B . Keeping the sawblade sharp . Replacing antikickback when removing the table insert , changing the cutting tool , removing or replacing the blade guard , pawls when points become dull . or making adjustments . C . Keeping sawblade guard , spreader , and antikickback L . Provide adequate support to the rear and sides of pawls in place and operating properly . The spreader the saw table for wider or long workpieces . must be in alignment with the sawblade and the M . Plastic and composition ( like hardboard ) materials pawls must stop a kickback once it has started . may be cut on your saw . However , since these are Check their action before ripping . usually quite hard and slippery , the antikickback D . NOT ripping work that is twisted or warped or does pawls may not stop a kickback . not have a straight edge to guide along the rip fence , Therefore , be especially attentive to following E . NOT releasing work untiI you have pushed it all the proper set - up and cutting procedures for ripping . way past the sawbiade . Do not stand , or permit anyone else to stand , in line F . Using a " PUSH STtCK " ( See Page 16 ) for ripping with a potential kickback . widths of 2 to B in . , and an auxiliary fence and push N . DO NOT perform layout , assembly , or setup work block for ripping widths narrower than 2 in . ( See on the table while the cutting tool is rotating . " Basic Saw Operation UsJngTbe Rip Fence " section . ) O . If you stall or jam the sawblade in the workpiece , G . NOT confining the cut - off piece when ripping or turn saw " OFF " , remove the workpiece from the crosscutting , sawblade , and check to see if the sawblade is H . When ripping apply the feed force to the section of parallel to the miter gauge grooves and if the the workpiece between the saw blade and the rip spreader is in proper alignment with the sawblade . fence . If ripping at the time , check to see if the rip fence is 9 . PROTECTION : EYES , HANDS , FACE , EARS , BODY parallel with the sawblade . Readjust as indicated . A . If any part of your saw is malfunctioning , has been 10 . KNOW YOUR CUTTING TOOLS damaged or broken . . , such as the motor switch , or orher operating contlol , a safety d _ vice or the A Dul ! , gummy , or improperly sharpened or " set cutting tOOIS can cause material to stick , jam , stall the saw , power cord , . , cease operating immediately until the particular part is properly repaired or replaced . or kickback at the operator . Minimize potential injury by proper cutting tool B . Wear safety goggles that comply with ANSI Z87 . 1 , and a face shield if operation is dusty . Wear ear and machine maintenance . NEVER ATTEMPT TO FREE A STALLED plugs or muffs during extended periods of SAWBLADE WITHOUT FIRST TURNING THE operation . SAW OFF . C . Small loose pieces of wood or other objects that
Page: 4

B . Never use grinding wheels , abrasive cut - off wheels , 16 . Never feed material into the cutting tool from the rear friction wheels ( metal slitting blades ) wire wheels or of the saw . An accident and serious injury could result . buffing wheels , 17 . THINK SAFETY . Safety is a combination of operator common senseand 11 . USE ONLY ACCESSORIES DESIGNED FOR THIS alertness at all times when the saw is being used , SAW . 18 . NOTE AND FOLLOW SAFETY INSTRUCTIONS 12 , Crosscutting operations are more conveniently worked THAT APPEAR ON THE FRONT OF YOUR SAW , and with greater safety f an auxiliary wood facing is attached to the miter gauge using the holes provided . DANGER However . the facing must not interfere with the proper FOR YOUR OWN SAFETY functioning of the sawbtade guard . READ AND UNDERSTAND OWNER'S MANUAL 13 . Make sure the top of the arbor or cutting tool rotates BEFORE OPERATING MACHINE : toward you when standing ir normal operating 1 . WEAR SAFETY GOGGLES aosition . Also make sure the cutting tool , arbor collars 2 . USE SAW - BLADE GUARD FOR " THRU - SAWING " and arbor nut are installed properly . Keep the cutting 3 . KEEP HANDS OUT OF PATH OF SAWBLADE tool as Fow as possible for the operation being 4 . USE A " PUSH - STICK " WHEN REQUIRED performed . Keep all guards in place whenever possible . 5 . KNOW HOW TO AVOID " ' KICKBACKS ' " 14 . Do not use any blade or other cutting tool marked for 6 . DO NOT PERFORM OPERATI ONS " FREEHAND " an operating speed less than 3450 RPM . Never use a 7 . NEVER REACH AROUND OR OVER SAW BLADE cutting tool larger in diameter than the diameter for which the saw was designed . For greatest safety and 19 . WARNING : DO NOT ALLOW FAMILIARITY efficiency when ripping , use the maximum diameter ( GAINED FROM FREQUENT USE OF YOUR SAW ) blade for which the saw is designed , since under these TO BECOME COMMONPLACE . - ALWAYS conditions the spreader is nearest the blade , REMEMBER THAT A CARELESS FRACTION OF A 15 . Adjust table inserts flush with the table top . NEVER SECOND IS SUFFICIENT TO INFLICT SEVERE Operate the saw unless the _ roper insert is installed . INJURY . WEAR YOUR The operation of any power tool can result in foreign objects being , thrown into the eyes , which can result m severe eye damage . Always wear safety goggles complying with ANSI Z87 . 1 ( shown on Package ) before commencing power tool operation . Safety Goggles are available at Sears retail or catalog stores . MOTOR SPECIFICATIONS AND ELECTRICAL REQUIREMENTS MOTOR SPECI FICATIONS 3 . As soon as the red button wi snap into running The AC motor used in this saw is a capacitor start , position , the saw may be started and operated normally non - reversible type , with the following specifications : by moving the saw switch lever to the " ON " position . Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 4 . Frertuent opening of fuses or circuit breakers may result Amperes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 if motor is overloaded , or if the motor circuit is fused Hertz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 with a fuse other than those recommended , Do not use Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Single0 a fuse of greater capacity without consulting the power RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345 company , Rotation ( viewec [ from 5 Although the motor is designed for operation on the Sawblade end ) . . . . . . . . . . . . . . Counterclockwise voltage and frequency specified on motor nameplate , normal loads will be handled safely on voltages not more than 10 % above or below the maneplate voltage . MOTOR SAFETY PROTECTION Heavy loads , however , require that voltage at motor The saw motor is equipped with a manual - reset thermal terminals by no _ less than the voltage specified oll overload protector , designed to open the power line circuit nameplate . when the motor temperature exCeeds a safe value . 6 . Most motor troubles may be tracec to loose or NOTE : The starting relay is a GRAVITY SENSITIVE incorrect connections , overloading , reduced input TYPE . NEVER TURN THE POWER ON WHILE THE SAW voltage ( which results when small size wires are used i = _ IS UPSIDE DOWN AS THiS WILL DAMAGE THE the supply circuit } or when the supply circuit is MOTOR extremely long . Always check connection , load and 1 , If the protector opens the line and stops the saw motor , supply circuit when the motor fails [ o aertorrn move the saw switch lever to the " OFF " position satisfactorily . Check wire sizes and lengths with table at immediately and allow the motor to cool . end of this section . 2 . After cooling to a safe operating temperature , the overload protector can be closed manually by pushing CONNECTING TO POWER SOURCE OUTLET in the red RESET button on the front of the saw . If the This saw must be grounded while in use to protect the operator from electrical shock . red I _ utton Will not snag into place immediately , the motor is still too hot and must be allowed to coo ! for a If power cord is worn or cut , or damaged in anv way , while longer . have it replaced immediately . 4
Page: 5

" If yoursawis for use on lessthan 150 volts it has a plug If the outlet you are planning to use for this saw is of the that looks like below . two prong type DO NOT REMOVE OR ALTER THE 3 - PRONG PLUG GROUNDING PRONG IN ANY MANNER . Use an adapter as shown and always connect the groundi . g lug to a known ground . It is recommended that you have a qualified electrician replace the TWO prong outlet with a properly grounded THREE 10rongoutlet . \ An adapter asshown below is available for conne _ ing plugs GROUNDING PRONG to 2 - prong receptacles , The green grounding lug extending from the adapter must be connected to a permanent ground PROPERLY GROUNDED such asto a properly grounded outlet box . 3 - PRONG OUTLET GROUNDING LUG Plug power cord into 110 - 120V properly grounded type outlet protected by a 1S - amp . time delay or Circuit - Saver ADAPTER fuse or circuit breaker . \ IF YOU ARE NOT SURE THAT YOUR OUTLET IS MAKE SURE THiS iS PROPERLY GROUNDED , HAVE IT CHECKED BY A 3 - PRONG CONNECTED TO A QUALI FlED ELECTRICIAN . PLUG KNOWN GROUND WARNING : DO NOT PERMIT FINGERS TO TOUCH THE TERMINALS OF PLUG WHEN INSTALLING OR 2 - PRONG REMOVING THE PLUG TO OR FROM THE OUTLET , RECEPTACLE WARNING : IF NOT PROPERLY GROUNDED THIS POWER TOOL CAN INCUR THE POTENTIAL HAZARD OF ELECTRICAL SHOCK , PARTICULARLY WHEN NOTE : The adapter illustrated { sfor use only if you already USED IN DAMP LOCATIONS : IN PROXIMITY TO have a properly grounded 2 - prong receptacle . PLUMBING , OR OUT OF DOORS . IF AN ELECTRICAL The use of any extension cord will cause some loss of SHOCK OCCURS THERE IS THE POTENTIAL OF A power . To keep this to a minimum and to prevent SECONDARY HAZARD SUCH AS YOUR HANDS over - heating and motor burn - out , use the table below to CONTACTING THE SAWBLADE . determine the minimum wire size ( A . W . G . ) extension cord . This saw is equipped with a 3 _ conductor cord and Use only 3 wire extension cords which have 3 prong grounding type plug which has a grounding prong , approved grounding type plugs and 3 - pole receptacles which w _ ll by Underwriters ' Laboratories and the Canadian Standards accept the plug on the saw . Association , The ground conductor has a green lug and is Extension Cord Length Wire Size A , W . G . attached to the toot housing at one end and to the ground prong in the attachment plug at the other end . Upto 100 Ft . . . . . . . . . . . . . . . . . . . . . . 12 This plug requires a mating 3 - conductor grounded type 100 - 200 Ft . . . . . . . . . . . . . . . . . . . . . . . 10 outlet asshown . 200 - 400 Ft . . . . . . . . . . . . . . . . . . . . . . . . . 8 CONTENTS Blade Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Table Insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 GENERAL SAFETY INSTRUCTIONS Removingand InstallingSawblade . . . . . . . . . . . . . . . 17 FOR POWER TOOLS . . . . . . . . . . . . . . . . . _ . . . . . . . 2 BASIC SAW OPERATION USING THE MITER GAUGE 17 ADDITIONAL SAFETY INSTRUCTIONS Work Helpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 FOR TABLE SAWS . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Crosscutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 MOTOR SPECIFiCATiONS AND ELECTRICAL Repetitive Cutting . . . . . . . . . . . . . . . . . . . . . . . . . . . lg REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Miter Cutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 UNPACKING AND CHECKING CONTENTS . . . . . . . . 6 Bevel Crosscutting . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Tools Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Compound Miter Cutting . . . . . . . . . . . . . . . . . . . . . . 2 ( ] List of Loose Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 BASIC SAW OPERATION USING THE RIP FENCE . . 20 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Installing Elevation and Tilt Handwheels . . . . . . . . . . . 7 Bevel Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Checking Table Insert . . . . . . . . . . . . . . . . . . . . . . . . . 7 Rasaw _ ng . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Checking Blade Squareness to Table . . . . . . . . . . . . . . 8 Cutting Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Checking Blade Elevation . . . . . . . . . . . . . . . . . . . . . . 8 Rabbeting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Attaching Table Extensions . . . . . . . . . . . . . . . . . . . . . 8 ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Installing Rip Fence Guide Bars . . . . . . . . . . . . . . . . . . g Miter Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Assembling Steel Legs . . . . . . . . . . . . . . . . . . . . . . . . 10 Heeling Adjustment or Parallelism of Mounting Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Sawblade to Miter Gauge Groove . . . . . . . . . . . . . . . 24 Aligning Table Extensions . . . . . . . . . . . . . . . . . . . . . 11 Blade Tilt , or Squareness of Aligning Rip Fence . . . . . . . . . . . . . . . . . . . . . . . . . . If Blade to Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 , $ Installing Blade Guard . . . . . . . . . . . . . . . . . . . . . . . . 13 Blade Elevation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 GETTING TO KNOW YOUR SAW . . . . . . . . . . . . . . . 15 Tilt and Elevation Mechanism . . . . . . . . . . . . . . . . . . 26 On - OffSwltah . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 LUBRICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ' 7 Elevation Handwheel . . . . . . . . . . . . . . . . . . . . . . . . . 16 RECOMMENDED ACCESSORIES . . . . . . . . . . . . . . . . 27 Tilt Handwheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . 2 , g Rip Fence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Miter Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 REPAIR PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Page: 6

UNPACKING AND CHECKING CONTENTS WARNING : FOR YOUR OWN SAFETY , NEVER z / / _ TOOLS NEEDED CONNECT PLUG TO POWER SOURCE OUTLET UNTIL ALL ASSEMBLY STEPS ARE COMPLETE , AND YOU HAVE READ AND UNDERSTAND THE SAFETY AND OPERATIONAL INSTRUCTIONS . Hammer Medium Screwdriver Small Sorewdriver LIST OF LOOSE PARTS Key No . PartName Qty , A MiterGauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 B Rip Fence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 C BladeGuardand Spreader . . . . . . . . . . . . . . . . . . . 1 112in . 9116in . D Handwheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Combination Square 3 / 4 in . E Rip FenceGuideBar , Rear . . . . . . . . . . . . . . . . . . 1 COMBINATION SQUARE MUST BE TRUE . F Rip FenceGuideBar Rod . . . . . . . . . . . . . . . . . . . 1 S _ AIGHT EDGE OF _ , ) ARD G Rip FenceGuideBar with Rip Scale ( Freut ) . . . . . 1 3 / 4 THICK . THIS EDG _ MUST DRAW LIGHT LiNE ON BE PERFECTLY STRAIGHT . H Arbor Wrench . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ROARD ALONG I'HIS EDGE * ¢ _ \ J Arbor Nut Wrench . . . . . . . . . . . . . . . . . . . . . . . . . 1 K OwnersMenuat . . . . . . . . . . . . . . . . . . . . . . . . . . 1 \ , Pkg . of MiscellaneouSsmall PartsNo . 627 ! 7 Consistingof the Following : L SpreaderSupport . . . . . . . . . . . . . . . . . . . . . . . . . . 1 M SpreaderClamp . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 LJ N SpreaderBracket . . . . . . . . . . . . . . . . . . . . . . . . . 1 P SetscrewWrench , l / Sin . . . . . . . . . . . . . . . . . . . . . 1 SHOULD BE NO 3AP OF OVERLAp 4ERE WHEN SQUARE { S FLII = PED P SetscrewWrench , 3 / 16 in . . . . . . . . . . . . . . . . . . . . 1 OVER { N DOTTED POSITION . Q Switch Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Model t 13.29570 Motorized Table Sew is shipped complete R GuideBar Spacer . . . . . . . . . . . . . . . . . . . . . . . . . . 2 in one carton but DOES NOT INCLUDE Table Extensions S Soc , Hd . Set ScrewI / 4 - 20 x 7 / 8 . . . . . . . . . . . . . . 2 and Steel Legs . T SquareNut , 1 / 4 - 20 . . . . . . . . . . . . . . . . . . . . . . . . 2 Model 113.295750 Motorized Table Saw is shipped U SelfThreadingNut . . . . . . . . . . . . . . . . . . . . . . . . 2 complete in one carton but INCLUDES TWO Table V Flatwasher , ( die , of hole 17 / 64 in . ) . . . . . . . . . . . . 4 Extensions and Steel Legs . V Flatwasher , ( dia . of hole 21 / 64 in . ) . . . . . . . . . . . . 4 Separate all parts from packing materials and check each W Hex Nut , 1 / 4 - 20 one with the illustration and the list of Loose Parts to make { Approx . dia . of hole 1 / 4 in . ) . . . . . . . . . . . . . . . 2 certain all items are accounted for , before discarding any packing material , W HexNut , 5 / 16 - 18 ( approx . die . of hole5 / 16 in . ) . . . . . . . . . . . . . . . 4 If any parts are mtssing , do not attempt to assemble the table saw , plug in the power cord or turn the switch on X Lockwasher , 1 / 4 in . ExternalType until the missing parts are obtained and are installed { approx . die , of hole1 / 4 in , ] . . . . . . . . . . . . . . . 4 correctly . A B ° j H G 6
Page: 7

X Lockwasher5 , / 16 in . ExternalType ( approx . dia . of hole5 / 16 in . ) . . . . . . . . . . . . . . . 4 X Luckwashar - # 10 ExternalType ( approx . die . of hole3 / 18 in . ) . . . . . . . . . . . . . . . 2 Y WingScrew , 1 / 4 - 20 x 1 / 2 { n . long . . . . . . . . . . . . . 2 Z Rex Hd . Screw , 5 / 16 - 18 x 1 - 1 / 2 im long . . . . . . . 2 B Z Hex Hd , Screw , 5 / 16 - f8 x 1 in . tong . . . . . . . . . . 2 AA Screw , Pro1Hd . 10 - 32 x 3 / 4 . . . . . . . . . . . . . . . . . . 2 The following parts are included with Model 113.295750 D Key No . Part Name Qty . A Leg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 B SideStiffener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 C EndStiffener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 I1 Table Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pkg . of Misce ! laneouSsmall Parts , No . 62659 Consistingof the Following : E Hex HeadScrew5 / 16 - - 18 x 1 - 1 / 4 in . long . . . . . 6 F Lockwashsr , 1 / 4 in . ExternalType ( appmx . dia , of hole1 / 4 in . ) . . . . . . . . . . . . . . 24 F Leckwasher , 5 / 16 in . ExternalType ( approx . dia . of hole 5 / 16 in . ) . . . . . . . . . . . . . 6 G HexNut , 1 / 4 - 20 ( approx . dia . of hole1 / 4 in . ) . . . . . . . . . . . . . . 24 H FlatWasher ( dia , of hole , 11 / 32 in . ) . . . . . . . . . . 6 G HexNut , 5 / 16 - ] 8 ( approx . die . of hole5 / 16 in . ) . . . . . . . . . . . . . S J TrussHeadScrew , 1 / 4 - 20 x 5 / 8 in . long ( top of screwis rounded ) . . . . . . . . . . . . . . . . . 24 G Hex Nut , 1 / 2 - 13 ( approx , die . af hole1 / 2 in . ) . . . . . . . . . . . . . . 8 K LevelingFoot . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 III ASSEMBLY Before mounting the saw on legs , a stand or a bench , the Table Insert and Blade Squareness and Blade Elevation must be checked at this time , LOCKWASHER LOCKWASHER INSTALLING ELEVATION AND TILT HANDWHEELS 1 . Line up FLAT SPOTS on shaft and handwheel , push handwhee ] onto shaft , Install screw and Iockwasber to lock handwheel on shaft . T SCREW SCREW TILT HANDWHEEL ELEVATION HANDWHEEL LEVELING TAB CHECKING TABLEINSERT I , With the insert in place , and sawblade all the way down , use a small scale or straight edge to check near each of the eight leveling tab positions , in order to determine if the insert is flush with saw table surface at all eight tab locations . 2 . If the insert is above the table surface , the leveling tabs must be adjusted . A . Loosen Screw . B . Lift insert from front end , and pull toward front of sew , C . Remove the insert , place it upside down on your workbench end GENTLY TAP each of the tabs downward only a slight amount . Replace insert . . . check it and readjust tabs , if necessary . 7
Page: 8

3 . If the insert is BELOW the table surface , remove the insert and bend the tabs ( with pliers ) enough to make the insert ABOVE the table surface . 4 . To replace insert . Place insert into insert opening in table and push toward rear of saw to engage spring clip and until keyslot in insert wi ! l drop over screw . Tighten screw . DO NOT TIGHTEN SCREW TO THE POINT WHERE IT DEFLECTS THE INSERT . CHECKING BLADE SQUARENESS TO TABLE IMPORTANT : BLADE must be SQUARE ( 90 ° ) to TABLE , in order to proceed with assembly . 1 . Turn ELEVATION handwheel clockwise until blade is up ashigh as it will go . 2 . Check for BLADE SQUARENESS . . . if blade is not square to table , adjust it at this time . MAKE SURE SQUARE NOTE : The Combination Square must be " TRUE " - IS NOT TOUCHING TiP OF TOOTH See start of " Unpacking and Checking Contents section on page 6 for checking method . Refer to " BLADE TILT , OR SQUARENESS OF BLADE TO TABLE " adjustments on page 24 . CHECKING BLADE ELEVATION Maximum depth of cut MUST NOT EXCEED TWO AND ONE HALE ( 2 - 1 / 2 INCHES . This adjustment iS set at the factory and should be checked to make sure that it has not changed due to rough handling during shipment . \ With the blade up as high asit will go , measure the distance from the top of the table to top of the highest saw tooth . If it is more than two and one half ( 2 = 1 / 2 ) inches , adjust it at this time . Refer to " BLADE ELEVATION " adjustments on page 26 . i f iii ATTACHING TABLE EXTENSIONS If you received two Table Extensions with your saw ( furnished with Model No . 113.295750 ) attach them at this time . 1 . Position saw upside down on floor . NOTE ; To protect the finished surfaces of the saw and extensions , lay a piece of heavy paper on the floor . 2 , From among the loose parts find the following hardware : 6 Hex Head , _ crew _ 6 / 16 . - - 18 × 1 in . long 6 Lockwashers , 5 / 16 in . External Type ( approx : die ; of hole 5 / 16 in , ) 6 Flat Washers ( dia . of hole 11 / 32 in . ) 6 Hex Nuts , 5 / 16 - 18 ( approx . die . of hole 5 / 16 in . ) 3 . Install screws , wasbars _ and nuts for extensions as FLAT WASHER shown . . , tighten screws SLIGHTLY . LOCKWASHER BE SURE END OF EXTENSIONS ARE EVEN WITH SCREW FRONT EDGE OF SAW . 4 . Leave saw in upside down position until you attach the rip fence guide bars and legs . $
Page: 9

EXT . LOCKWASHER HEX . HEAD SCREW 5 / 16 IN . I IN . LONG FLAT WAS ½ ER / INSTALLING RIP FENCE GUIDE BARS 1 . From among the loose _ rts find the following hardware : HEX NU 5 / 16 2 Flex . Head Screws . 5 / 16 - 18 x 1 - I / 2 in . long 2 Flex . Head Screws , 5 / 16 - 18 x 1 in , long 4 Hex , Nuts , 5 / 16 - 18 ( approx . dia . of hole 5 / 16 in . ) 4 External Lockwasbers , 5 / 16 in . ( approx . dia . of hole 5 / 16 in , ) 4 Flat Washers ( Dia . of hole 21 / 64 in , ) 2 Spacers , 3 / 4 in . dia , x 1 / 2 in . Ionf ! 2 Self - threading nuts 2 . Position guide bars on floor and instal hardware as shown . . , do not screw nuts on all the way , FRONT GUIDE BAR 3 . Place front guide bar against saw table and drop it in place . . . engaging the screws in the slot s . Make sure the spacers are between the rail and the table . 4 . End of front guide bar must be 5 : 13 / 16 in . from side of saw table . Thi _ is important so that rip fence pointer can be aligned . 6 . With the blade of your combination square set to 1 / 4 in . , use it as a gauge and attach the rail so that the edge of the rail is 1 / 4 in . ABOVE the edge of the table . / 5 - 13 / 16 IN . FENCE GUIDE BAR ROD 6 , Remove the three screws from rear of table extension , 7 , Insert ends of FENCE GUIDE BAR ROD through round holes at outer end of bars . NOTE : The ends of the ROD are not threaded . . . the SELF THREADING NUTS will cut threads on the rod as they are'screwed on . 8 . Attach the rear bar in a similar manner , but make sure that the end of the bar is 8 - 5 / 8 in . from the side of the saw table . 9
Page: 10

SCREWS THROUGH HOLES MARKED " X " ASSEMBLING STEEL LEGS NOTE : Steel Legs are furnished with Model 113.295750 , From among the loose parts , find the following Hardware : 24 Truss Head Screws , 1 / 4 - 20 x 5 / 8 in . long ( top of SIDE STIFFENER screw is rounded ) 24 Lockwashers , 1 / 4 in . External Type ( approx . dia . of hole 1 / 4 in . ) 24 Hex Nuts , 1 / 4 - 20 ( approx , dia . of hole 1 / 4 in . } 8 Hex Nuts , 1 / 2 - - 13 ( approx . dia . of hole 1 / 2 in . ) 4 Leveling feet , Assemble the legs asshown . . . END STIFFENER _ 1 . Insert the Truss Head Screws through the holes in the legs , then through the holes in the stiffeners , MAKE SURE THE SCREWS GO THROUGH THE HOLES IN THE SIDE STIFFENERS MARKED " X " . 2 . Install Iockwashers and screw on the nuts but do not tighten until completely assembled . 3 . Install leveling feet . _ : _ . , . _ . . - - - - - LEVELING FOOT MOUNTING SAW I , Remove the four Truss Head screws , flatwashers , Iockwashers and nuts from bottom of saw . 2 . Position legs as shown and line up holes in stiffeners with holes in saw base . NOTE : At front of saw you will see four , _ etsof holes . Insert bolts through holes closest to front of saw . these holes are 9 - 1 / 4 ' " apart . Replace the screws , washers , Iockwashers and nuts . . . tighten the nuts . 3 . Place saw m upright position . T , i , i i , , , , , ) / 2 If you mount the saw on any other bench , make sure that there is an opening in the top of the bench the same size as the opening in the bottom of the saw so that the sawdust can drop through . Recommended working height is 33 to 37 in . from the top of the saw table tothe floor . / 4 HOLES ; ; ' / 16 OIA . NOTE : All dimensions in inches , FRONT OF SAW i0
Page: 11

ALIGNING TABLE EXTENSIONS 1 . " TAD " extensions upwards or downwards , using a block of wood and a hammer until they are even with top of saw table . Be sureend of extensions are even with front BLOCK OF WOQD edge of saw , 2 . Tighten screws . 3 . Lay a straight piece of wood or a framing square on table to act as a straightedge . If outer edge of extension is higher or lower than table surface : A , Slightly loosen nuts holding bracket to extension using 7 / 16 in . wrench . B . Move end of extension up or down until outer edge is even with table surface . . . check with GUIDE BAR , . . tighten nuts . C . Recheck INNER edge of extension to make sure it has not moved . . . readjust , if necessary . 4 . Replace three screws in rear of table extension on right side . 5 . Hold rod with one hand and with a 7 / 16 in . wrench or pliers start screwing on ONE of the nuts only A TURN OR TWO . . . screw on other nut the same way . Using TWO 7 / 16 in . wrenches or pliers tighten both of the nuts . IMPORTANT : Apply a coat of paste wax to the top surface and front edge of the front guide bar . This will allow the fence to slide more easily . ALIGNING RIP FENCE 6 . Position rip fence over miter gauge groove , holding up the rear end while engaging front end with bar . . . lower fence onto table , 11
Page: 12

The rip fence must be PARALLEL with the sawblade and Miter Gauge grooves . . . Move fence until it is along side of groove . Do NOT LOCK IT . It should be I _ arallel to groove . If it is not ; A . Loosen the two " Hex . Head Screws . " B . Hold fenCe head tightly against bar . . . move end of fence so that it is parallel with groove . C . Tighten handle . D . Alternately tighten the screws , Place fence on saw but DO NOT LOCK IT . Move the REAR END of the fence slightly to the right or left . . . when you release it , the fence should " spring " back to its original position . If it does not , the spring pressure must be INCREASED . 1 . Loosen the screws , 2 . Move Spring slightly toward front of fence . If the fence does not slide easily along the bars , the pressure of the spring can be REDUCe , 1 . Loosen the screws . 2 . Move spring slightly toward r _ ar of ( t _ ncc . . . tighten screws . 12
Page: 13

ADJUSTING RIP SCALE POINTER 1 , Turn ELEVATION handwheel clockwise until blade is up ashigh asit will go , IMPORTANT : BLADE must be SQUARE ( 90 ° ) to TABLE , in order to ALIGN rip fence , 2 . Position fence on right side of sawblade so that it touches the sides of the teeth . . , tighten lock knob . 3 . Loosen screw holding the pointer . . . adjust pointer so that it points to " 0 " . . . tighten screw . . . . . NOTE : If you cannot adjust pointer so that it points to " 0 " , loosen the screws holding the front guide bar and LOCK KNOB move the guide bar . INSTALLING BLADE GUARD 1 . From among the loose parts , find the hardware as shown . 2 . MAKE SURE THE BLADE IS ALL THE WAY UP AND SQUARE WITH THE TABLE . BLADE SQUARI 3 . Position SPREADER SUPPORT on rod until it is even WITH TABLE with the end of the rod . 4 . Assemble the 7 / 8 in . long setscrews , nuts , Iockwashers and washers to the SPREADER SUPPORT BRACKET and slip the nuts into the slot in the spreader support . 5 . Finger tighten ONLY THE HEX NUTS .
Page: 14

6 . Lay a piece of flat straight wood and a square on sawhe table and rotate the SPREADER SUPPORT until t bracket is aligned with square . 7 . MAKE SURE END OF SUPPORT , BRACKET AND ROD ARE EVEN . , , using an 1 / 8 in . setscrew wrench , TIGHTEN THE SET SCREWS ONLY . SPACE EQUAL TC APPROX KERF WOOD 3 THICKNESSE ! OF PAPER IMPORTANT : The SPREADER must always be BLADE PARALLEL to the sawblade and in the MIDDLE of the cut \ ( KERF ) made by the sawblade . NOTE : The spreader is thinner than the width of the KERF by approximately six thicknesses of paper . SPACE EQUAL TO APPRO _ LOOKING DOWN ON SAW 3 THICKNESSES OF PAPER 8 _ Make two folds in a small piece ( 6 x 6 in . ) of ordinary NEWSPAPER making three thicknesses . The folded paper will be used as a " ' specing gauge " . PIECE OF ANTIKICK BACK PAWLS STRAIGHT WOOD 9 , Install the SPREADER CL . tW1P . Place spreader between TIGHTLY AGAINST HOLD WOOD 1 spreader clamp and bracket , Move forward until all BLADE three are in line . TIGHTEN WlNGSCREWS . THREE 10 . Lift up both ANTIKICKBACK PAWLS . . . insert one THICKNESSES of the setscrew wrenches or a pencil in the notches to OF PAPER hold the pawls out of the way . 11 . Lay a piece of straight flat wood against the sawblade . Insert folded paper between spreader and strip of wood . 12 . MAKE SURE THE HEX NUTS UNDERNEATH ARE LOOSE . 13 . Hold the spreader tightly against the wood and make sure the wood is against the saw blade . TIGHTEN THE SPREADER HEX NUTS . TIGHTLY AGAINST WOOD / This will align the spreader in the middle of the cut SPREADER SPREADER ( KERF ) made by sawblade . CLAMP _ RACKET
Page: 15

. GETTING TO KNOW YOUR SAW MITER GAUGE 7 BLADE GUARD ANTtKICKBACK LOCK KNOB PAWLS MITER GAUGE 9 SAW BLADE SPREADER 5 6 MITER GAUGE HEAD R _ P FENCE \ HOLES FOR FACING 4 Tilt HANDWHEEL 3 ELEVATION RIP FENCE LOCK KNOB 2 RESET BUTTOt ! 0 N - OFF SWITCH I ON - OSFWF , TCR II ; CAUTION : Before turning switch on , make sure the blade guard is correctly installed and operating properly . The On - Off Switch has a locking feature . THIS SHOULD PREVENT UNAUTHORIZED AND POSSIBLY @ HAZARDOUS USE BY CHILDREN AND OTHERS . KEY A . Insert key into switch . KEY YELLOW PLASTIC ) B . TO turn saw ON . , , stand to either side of the ON - OFF SWITCH blade never in line with it , , . insert finger under switch lever and pull END of lever out . After turning switch ON , always allow the blade to come up to full speed before cutting . Do not cycle the motor switch on and off rapidly , as this may cause the sawblade to loosen , In the event this should ever occur , allow the sawblade to come to a complete stop and retighten the arbor nut normally , not excessively . Never leave the saw while the power is " ON " . - - 4z : _ j j C . TO turn saw OFF . , . PUSH lever in , Never leave the saw until the cutting tool has come to a complete stop . D . TO lock switch in OFF position , . , hold switch IN F with one hand . . , REMOVE key with other hand . / WARNING : FOR YOUR OWN SAFETY , LOWER BLADE OR OTHER CUTTING TOOL BELOW TABLE SURFACE . ( IF BLADE IS TILTED . RETURN IT TO VERTICAL ( 90 ° ) POSITION ) . ALWAYS LOCK THE SWITCH " OFF " . WHEN SAW I : S NOT IN USE , . . REMOVE KEY AND KEEP IT IN A SAFE PLACE . . . ALSO . . . IN THE EVENT OF A POWER FAILURE ( ALL OF YOUR LIGHTS GO OUT ) TURN SWITCH OFF . . . LOCK IT AND REMOVE THE KEY . THIS WILL PREVENT THE SAW FROM STARTING UP AGAIN WHEN THE POWER COMES BACK ON . 15
Page: 16

2 RESET BUTTON . . See " Motor Specifications and NOTE : When bevel crosscutting , attach facing so that it Electrica Requirements " section . " Motor Safety extends to the right of the miter gauge and use the miter Protection . " gauge in the groove to the right of the blade . 3 ELEVATION HANDWHEEL . . . elevates or lowers the blade . Turn clockwise to elevate . . , counterclockwise to lower . NOTE : WHEN THE BLADE IS TILTED TO 45 ° , IT CANNOT BE LOWERED ALL THE WAY BELOW THE TABLE . IT WILL PROJECT APPROX . 1 / 2 IN \ \ \ \ 4 TILT HANDWHEEL . . . tilts the blade for bevel cutting . Turn clockwise to tilt toward left . . . counterclockwise to tilt toward right . 7 BLADEGUARD must always he in place and working properly for all thru - sawing cuts . That is , all cuts When the blade is tilted to the LEFT asfar as it will go , whereby the blade cuts completely through the it should be at 45 ° to the table and the bevel pointer workpiece . should point 45 ° . To remove the guard for special operations , loosen the NOTE : There are LIMIT STOPS inside the saw which wmgscrews and move spreader awm / from saw and lift prevent the blade from tilting beyond 45 ° to the LEFT upwards . DO NOT DISTURB THE SETTING OF THE REX NUTS . and g0 ° to the RIGHT . ( See " Adjustments " section " Blade Tilt . or Squareness of Blade to Table " ) . When replacing the guard , make sure the spreader is moved toward front of saw so that wingscrews are at end of slots . TIGHTEN THE WlNGSCREW _ S 5 SECURELY . RIP FENCE . . . is locked in place by tightening the lock knob . To move the fence , oose _ the lock knob and grasp the fence with one hand at the front . 8 TABLE INSERT is removable for removing or installing blades or other cutting tools . . Holes are provided in the rip fence for attaching a wood facing when using the dado head , or molding head . Select a piece of smooth straight wood appro × , 3 / 4 in , ANTIKICK BACK thick and the same size as the rip fence . PAWLS Attach it to the fence with three Round Head # f0 Wood Screws 2 in , long . To remove the facing , loosen the screws , slide the facing forward and pull the screws throu _ the round holes . WOOD FACING \ \ # 1oWOOD SCREWS WARNING : FOR YOUR OWN SAFETY , TURN SWITCH " OFF " AND REMOVE PLUG FROM POWER SOURCE 6 MITER GAUGE . . head is locked in position for OUTLET BEFORE REMOVING INSERT . crosscutting or mitering by tighting the lock knob , A , Lower the blade below the table surface . ALWAYS LOCK IT SECURELY WHEN IN USE . B . Loosen screw . C . Lift antikickback pawls . Notches are provided in the miter gauge for attaching D . Lift insert from front end , and pull toward front of an AUXILIARY FACING to make it easier to cut long saw . pieces , Be positive facing does not interfere with the NEVER OPERATE THE SAW WITHOUT THE PROPER proper operation of the sawblade guard . INSERT IN PLACE . USE THE SAW BLADE INSERT Select a suitable piece of smooth straight wood . . , drill WHEN SAWING . , . USE THE COMBINATION DADO two holes through it and attach it with screws . MOLDING INSERT WHEN DADOING OR MOLDING . 16
Page: 17

_ \ \ PULL TO LOOSEN REMOVING AND INSTALLING SAWBLADE _ O TIGHTEN WARNING : FOR YOUR OWN SAFETY , TURN SWITCH " OFF " AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE REMOVING OR INSTALLING SAWBLADE . A . Remove insert , ARBOR B . Place ARBOR wrench on flat surfaces of saw ARBOR . . . ARBOR NUT wrench on nut . . . position wrenches as shown . . . hold your hands well aboveblade , C . With ARBOR wrench against table , PULL ARBOR NUT wrench FOREWARD to LOOSEN nut . D . To TIGHTEN nut , . . HOLD ARBOR wrench against rear of table . o . PUSH ARBOR NUT wrench toward rear . NOTE : When installing the blade . . . make sure the teeth are pointing toward the fiont of the saw . . , and FLAT SURFACES COLLAR / / that the blade and collars are clean , and free from any / / burrs . The HOLLOW side of the collars must be against the blade . Always tighten the arbor nut securely . HEX NUT E . To replace insert , 1 Place insert into insert opening in table and push TEETH FOI toward rear of saw until keyslot in insert will drop FRONT OF SAW over screw . Tighten screw . Do not tighten screw to the point where it will deflect the insert . BASIC SAW OPERATION USING THE MITER GAUGE 8 . If blade stalls or stops while cutting , TURN SWITCH CROSSCUTTING , MITER CUTTING , BEVEL CUTTING , OFF before attempting to free the blade . COMPOUND MITER CUTTING and when RABBETING across the end of narrow workpiece , THE MITER GAUGE 9 . Do not reach over or behind the blade to pull the IS USED . workpiece through the cut . . , to support long or heavy workpieees . . , to remove cot - off pieces of material or WARNING : FOR YOUR OWN SAFETY , ALWAYS FOR ANY OTHER REASON . OBSERVE THE FOLLOWING SAFETY PRECAUTIONS 10 . Do not pick up small piecesof cut - off material from the IN ADDITION TO THE SAFETY INSTRUCTIONS ON table . REMOVE them by pushing them C FF the table PAGES 2,3 , and 4 . with a long stick . Otherwise they could be thrown back at you by the rear of the blade , 1 , Never make these cuts freehand ( without using the 11 . Do not remove small piecesof cut - off material that may miter gauge or other auxiliary devices ) because theor become TRAPPED inside the blade guard while the sew blade could bind in the cut and cause a KICKBACK is RUNNING . THIS COULD ENDANGER YOUR cause your fingers or hand to slip into the blade , HANDS or cause a KICKBACK . 2 . Always lock the miter gauge securely when in use . Turn the saw OFF . After the blade has stopped turning , 3 , Remove rip fence from table . lift the guard and remove the p _ ece . 4 , Make sure blade guard is installed for all " THRU - SAWING " operations ( when sawblade cuts entirely thru the thickness of the workpiece . ) Replace guard WORK HELPERS IMMEDIATELY after completion of dadoing , molding or rabbeting cuts . Before cutting any wood on your saw , study all of the 5 . Have blade extend approximately 1 / 8 in . above top of " Basic Saw Operations " . workpiece . Additional blade exposure would increase Notice that n order to make some of the cuts , it s the hazard potential . necessary to use certain devices " Work Helpers " like the 6 . Do not stand directly in front of the blade in case of a Push Stick the Push Block and the Au × iliarv Fence which THROWBACK ( Small cot - off piece caught by the back you can make yourself . of the blade and thrown toward the operator ) . Stand to After you have made a few practice cuts , make these either side of the blade . " helpers " before starting any projects . Make the " ' Pusll 7 . Keep your hands clear of the blade and out Of the path Stick " first . of the blade . 17
Page: 18

THESE EDGES MUST WOOD _ E PARALLEL NOTCH 3 / 8 PLYWOOD NOT'E : All dimensions _ n inches PUSH STICK PUSH BLOCK PUSH STICK AND PUSH BLOCK Make the Push Stick using a piece of 1 x 2 , or rip one from 3 / 4 pLYWOOD a wide board , say 11 - 1 / 2 in , wide , and set the rip fence 9 - 7 / 8 in . from the sawblade . Make the Push Block using a piece of 3 / 8 in . and 3 / 4 in . plywood . The small piece of wood 3 / 8 in . x 3 / 8 in . × 2 - 1 / 2 in . should be GLUED to the plywood . . . DO NOT USE NAILS . This is to prevent dulling the sawblade in the event you mistakingly cut into the push block . Position the handle in the center of the plywood and fasten tosether with glue and woodscrews . THIS FACE AND THIS EDGI AUXI LIARY FENCE EDGE MUST BE PARALLEL Make one using a piece of 3 / 8 in . and 3 / 4 in . plywood . 3 / 8 pLYWOOD Fasten _ ogether with glue and woodscrews _ NOTE : Since the Push Block is used with the Auxiliary NOTE : All d _ menslons _ n inches Fence , the 4 - 3 / 4 in . dimensions must be held identical on both the pieces . AUXILIARY FENCE CROSSCUTTI NG CROSSCUTTING is known as cutting wood across the grain , at 90 O , or square with both the edge and the flat side of the wood . This is done with miter gauge set at " 0 " . PLYWOOD The graduations on the mite'r gauge provide accuracy for CLAMP _ . D average woodworklng . In Some cases where extreme tO SAWHORSE accuracy is required , when making angle cuts ; for example , make a trial cut and ' then recheck it with an accurate square , or protractor . If necessary , the miter gauge head can be swiveled slightly to compensate for any inacurracy . NOTE : The space between the miter gauge bar and the groove in the table is held to a minimum during manufacturing . For maximum accuracy when using the miter gauge , always " favor " one side of the groove in the table . In other words , don't move the miter gauge from side to side while cutting , but keep one side of the bar riding against one side of the groove . NOTE : Glue a piece of sandpaper to the face of the miter gauge head . This will help prevent the workpiece from " creeping " while it is being cut . The Hold - Down Clamp ( Optional Accessory ) should be When using the RIGHT hand groove , hold the workpiece used on the miter gauge for greater accuracy . with your right hand and the lock knob with your left hand . The miter gauge may be used in either of the grooves in the table . Make sure it is locked . When crosscutting a long board , make sure that it is supported . When using the miter gauge in the LEFT hand groove , hold the workpieee firmly against the miter gauge head with You can make a simple support by clamping a piece of plywood to a sawhorse . your left hand , and grip the lock knob with your right . _ 8
Page: 19

When cutting long workpieces , invert the AUXILIARY \ FENCE ! WORK SUPPORT , and position it on top of the guide bars to support the workpiece as near to the end as possible . If this does not adequately support the workpiece , you can make a simple support by clamping a piece of plywood to a sawhorse . Use the Hold - Down Clamp ( Optional Accessory ) on the miter gauge for greater accuracy . AUXILIARY WORK SUPPORT STOP RODS REPETITIVE CUTTING \ REPETITIVE CUTTING is known as cutting a quantity of pieces the same length without having to mark each piece . 1 . Use the Stop Rods ( optional accessory ) only for cutting duplicate pieces6 in , long and longer . 2 , DO NOT FEED workpiece with RIGHT hand , merely guide it , making sure that it does not bind or pinch the sawblade . When making repetitive cuts from a long workpiece , make sure it is adequately supported . Use the Hold - Down Clamp ( Optional Accessory ) on the miter gauge for greater accuracy . \ 1 . NEVER USE THE RIP FENCE AS A LENGTH STOP BECAUSE THE CUTOFF PIECE COULD BIND BLOCK BETWEEN THE FENCE AND THE BLADE CAUSING A KICKBACK . 2 . When making repetitive cuts shorter than 6 in . , clamp a block of wood 2 in . long to the table to act as a length stop , Do not clamp directly to the bottom edge of the table because the " swivel " of the clamps will not grip properly . Place a small block of wood between the bottom edge of the table and the " C " clamps . CAUTION : When clamping the block , make sure that the end of the block is well in front of the sawblede , Be sure it is clamped securely , 3 . Slide the workpiece along the miter gauge until it touches the block . . , hold it securely or clamp it with the Hold - Down Clamp ( Optional Accessory ) . CUT OFF PIECE 4 . Make the cut . . , pull the workpiece beck . . , push the cut off piece off the table with a tong push stick . . . OOD NOT ATTEMPT TO PICK IT UP AS THIS COUL ENDANGER YOUR HANDS . 19
Page: 20

MITER CUTTING MITER CUTTING is known : as cutting wood at an angle ott _ er than 90 ° with the edge of the wood . Follow the same procedure as you would for crosscutting , Adjust the miter gauge to the desired angle , an _ lock it . The miter gauge may he used in either of the grooves in the table . When using the miter gauge in the LEFT hand groove , hold the workpiece firmly against the miter gauge head with your left hand , and grip the ock knob with your right . When using the RIGHT hand groove , hold the workpiece with your right hand and the lock knob with your left hand . Use the Hold - Down Clamp ( Optional Accessory ) on the miter gauge for greater accuracy , BEVEL CROSSCUTI NG BEVEL CROSSCUTTING is the same as crosscutting except that the wood is also cut at an angle . . , other than 90 ° with the flat side of the wood . Adjust the blade to the desired angle . Use the Miter Gauge in the groove to the RIGHT of the blade . It cannot be used in the groove to the left because the blade guard will interfere . Hold the workpiece with your right hand and the lOCKknob with your left hand . Use the Hold - Down Clamp ( Optional Accessory ) on the miter gauge for greater accuracy , COMPOUND MITER CUTTING COMPOUND MITER CUTTING is a combination of miter cutting and bevel crosscutting . The cut is made at an angle other than 90 ° to both the edge and the flat side of the wood . Adjust the miter gauge and the blade to the desired angle . . Make sure miter gauge is locked , USING THE RIP FENCE RIPPING , BEVEL RIPPING , RESAWING AND 5 , Have blade extend approximately 1 / 8 in . above top of RABBETING are performed using the RIP FENCE togetherH workpiece . Additional blade exposure would increase with the AUXILIARY FENCE . PUSH STICK OR PUS the hazard potential . BLOCK 6 . Do not stand directly in front of the blade in case of a WARNING : FOR YOUR OWN SAFETY , ALWAYS KICKBACK . Stand to either side of the blade . OBSERVE THE FOLLOWING SAFETY PRECAUTIONS 7 . Keep your hands clear of the blade and out of the path IN ADDITION TO THE SAFETY INSTRUCTIONS ON of the blade . PAGES 2 , 3 , and 4 , 8 . If the blade stalls or stops while cutting , TURN 1 . Never make these cuts FREEHAND ( without usingthe SWITCH OFF before attemptingto free the blade , rip fence or auxiliary devices when required ) becausea 9 _ Do not reach over or behind the blade to pull the the blade could bind i _ the CUt and cause workpiece through the cut . . , to support long or heavy KICKBACK . workpieces . . . to remove small cut - off p = eces of 2 . Always lock the tip fence securely when in use . material or FOR ANY OTHER REASON . 3 . Remove miter gauge from table . 10 . Do not pick up small pieces of cut'off material from the 4 . Make sure blade guard is installed for all thru - sawing table . REMOVE them by pushing them OFF the table type cuts . Replace the guard IMMEDIATELY following with a long stick . Otherwise they could be thrown back completion of resawing , rabbeting , dadoing , or molding at you by the rear of the blade . operations . 1 f . Do not remove small pieces of cut - off material that may Frequently check the action of the ANTIKICKBACK become TRAPPED insidethe blade guard while the saw PAWLS by 0assing the workpiece alongside of the is RUNNING . THIS COULD ENDANGER YOUR spreader while saw is'OFF . HANDS or cause a KICKBACK . Pull the workpiece TOWARD you . If the PAWLS do Turn the saw OFF . After the blade has stopped turning , not DIG into the workpiece and HOLD it . . . the pawls lift the guard and remove the piece . must be SHARPENED . See " Maintenance " sectior 20
Page: 21

RIPPING ALWAYS SUPPORT LONG WORKPIECES RIPPING is know as cutting a piece of wood wffh the grain , or lengthwise . This is done using the rip fence . Position the fence to the desired WIDTH OF RIP and lock in place . Before starting to rip , be sure A . Rip Fence is parallel to sawblade . 13 . Sprcader is properly aligned with sawblade . C . Antikickback pawls are functioning properly . When ripping LONG BOARDS or LARGE PANELS , always use a work support . A simple one can be made by clamping a piece of plywood to a sawhorse . BEVEL RIPPING When bevel ripping material 6 in . or narrower , use fence on the right side of the blade ONLY , This will provide more space between the fence and the sawblade for use of a push stick . If the fence is mounted to the left , the sawblade guard may interfere with proper use of a push stick . When " WIDTH OF RIP " is 6 in . and WIDER use your RIGHT hand to feed the workpiece until it is clear of the table . Use LEFT hand ONLY to guide the workpiece . . , do not FEED the workpiece with the left hand , When " WIDTH OF RIP " is 2 in . to 6 in . wide USE THE PUSH STICK to feed the work When WIDTH OF RIP is NARROWER than 2 in . , the push stick CANNOT be used because the guard will interfere , . . USE the AUXILIARY FENCE / WORK SUPPORT and PUSH BLOCK . Attach Auxiliary Fence / Work Support to rip fence with two " C _ ' clamps . AUXILIARY PENCF / / WORK SUPPORT 21
Page: 22

Feed the wOrkpiece by hand along the AUXLIARY FENCE / WORK SUPPORT Until the end is approx . 1 in . past the front edge Of the table . Continue to feed using the PUSH BLOCK . Hold the workpiece in position and install the PUSH BLOCK by Sliding it on top of the AUXILIARY FENCE ! WORK SUPPORT ( this may raise guard ) . BAFFLE Narrow strips thicker than the Auxiliary Fence / Work Support may enter the guard and strike the baffle . CAREFULLY raise guard only enough to clear the workpiece . Use PUSH BLOCK to complete cut , RESAWING RESAWING is known as ripping a piece of wood through its thickness . Do not attempt to resaw BOWED or WARPED material NOTE : to RESAW a piece of wood wider than 2 - 1 / 2 in . . . . it will be necessary to remove the blade guard . . . and use the AUXILIARY FENCE / WORK SUPPORT ( See Page 18 ) Clamp it to the table so that the workpiece will SLIDE EASILY ( but not TILT or MOVE SIDEWAYS ) without SMALL BLOCK BI NDI NG between the two fences . OF WOOD Do not clamp directly to the bottom edge of the table / because the " swivel " of the clamps wilt not grip properly . Place a small block of wood between the bottom edge of the table and the " C ' " clamps , WARNING : FOR YOUR OWN SAFETY . . . 1 DO NOT " BACK UP " ( REVERSE FEEDING ) WHILE 2 . INSTALL BLADE GUARD IMMEDIATELY UPON RESAWING BECAUSE THIS COULD CAUSE A COMPLETION OF THE RESAWING OPERATION . KICKBACK . _ , UXlLIMY FENCE / " WORK SUPPORT / CUTTING PANELS When cutting panels ( whenever fence is positioned outside of table surface ) , ALWAYS use the AUXILIARY F ENCE / WOR K SUPPORT . 1 , Unlock fence and raise rear end . 2 . Position AUXILIARY FENCE _ VORK SUPPORT as shown and attach it with two " ' C " clamps . 22
Page: 23

RABBETING Rabbeting is known as cutting out a section of the corner of a piece of material . To make a RABBET requires two cuts which do not go all the way through the material . Therefore the blade guard must be removed . 1 . Remove blade guard . 2 . Adjust rip fence and blade to required dimensions . 3 . Make first cut through edge . Follow resawing procedure . 4 . Remove auxiliary fence and make second cut . 5 . INSTALL BLADE GUARD IMMEDIATELY UPON COMPLETION OF RABBETING OPERATION . Rabbet cuts can also be made using the dado head or molding head . DADOING Instructions for operating the Dado Head are contained in DADO INSERT booklet furnished with the Dado Head . / The recommended Dado Head is listed , under recommended Accessories . The arbor on the saw , is only long enough so that the HEAD widest cut that can be made is 13 / 16 " wide . When installing the dado head on the arbor , ALWAYS ; install the inside " loose collar " first . LOOSE It is not necessary to install the outside loose collar before screwing on the arbor nut . Make sure the arbor nut is tight . ARBOR NUT ALWAYS USE DADO INSERT listed under recommended Accessories , When using the dadoing head it will be necessary to remove the Blade Guard and Spreader . USE CAUTION . ALWAYS REPLACE THE BLADE GUARD AND SPREADER WHEN YOU ARE FINISHED DADOING . MOLDING CUTTING Instructions for operating the Molding Head are contained in a booklet furnished with the Molding Head . When using the molding head it will be necessary to remove The recommended molding head is listed under the Blade Guard and Spreader . USE CAUTION . recommended Accessories . ALWAYS REPLACE THE BLADE GUARD AND Always use Molding Insert listed under recommended SPREADER WHEN YOU ARE FINISHED MOLDING : Accessories . KNOB ADJUSTMENTS WARNING : FOR YOUR OWN SAFETY , TURN SWITCH " OFF " AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE MAKING ANY ADJUSTMENTS . MITER GAUGE NOTE : The graduations on the miter gauge provide accuracy for average woodworking . In some cases where extreme accuracy is required , when making angle cuts , for BAR example , make a trial cut and then recheck it with an accurate square or protractor . If necessary , the miter gauge head can be swiveled slightly 2 . Position the head square with the bar . . . tighten the lock knob . 1 : ocompensate for any inaccuracy . The HEAD should be SQUARE ( 90 ° ) with the bar when 3 . Loosen the screw and adjust the pointer , so it points to the pointer points to " 0 " , zero . To check for squareness , place an accurate square on the The swiveling movement of the head can be adjusted by miter gauge . If the head is NOT SQUARE with the bar : tightening or loosening the set screw located in side of the head using the t / 8 in . setscrewwrench . 1 . Loosen the lock knob . 2S
Page: 24

HEELING ADJUSTMENT or PARALLELISM OF SAWBLADE TO MITER GAUGE GROOVE While cutting , the material must move in a straight hlinee PARALLEL to the SAWBLADE . therefore both t miter gauge GROOVE and the RIP FENCE must be PARALLEL to the SAWBLADE . If the sawblade IS NOT para ) lel to the miter gauge groove , the blade will bind at one end of the cut , ( This is known as " ' HEELING " ) . To check for p _ rallelism : WARNING - FOR YOUR OWN SAFETY , TURN SWITCH " OFF " AND REMOVE PLUG FROM POWER SOURCE OUTLET . 1 . Raise blade all the way up . . . raise blade guard . 2 . Mark an " X " on one of the teeth which is SET ( bent ) to the LEFT . 3 . Place the head of a combination square in the GROOVE . . adjust blade of square so that it just touches the tip of the MARKED tooth . 4 . Move square to REAR , rotate blade to see if MARKED tooth again touches blade of square . 5 . ) f tooth touches square the same amount at FRONT and REAR . . . sawblade s PARALLEL to MITER GAUGEGROOVE . if tooth does not touch front and rear . . , the mechanism underneath must be adjusted to make the blade PARALLEL to GROOVE . 3 / 16 IN . SETSCREW 1 , Loosen the 4 screws ( about 1 / 4 to 1 / 2 turn ) using 3 / t16he WRENCH in . setscrew wrench furnished with saw . Also loosen 2 pan head 10 - 32 screws ( about 1 / 4 to 1 / 2 turn ) located at rear of the table top asshown . This will allow the mechanism below the table to be shifted sideways . 2 . Fold a piece of cardboard or heavy paper over the blade to protect your hands . 3 . Graso the blade and move it to the right or left a small amount and tighten one of the screws . 4 . Check with square to determine if MARKED TOOTH touches square the same amount at front and rear . It it does , tighten other three screws . If it does not , loosen screw and move blade the required amount , 5 . Alternately tighten the screws slowly . NOTE : Use the setscrew wrench as shown . . , do not use a pair of pliers or any other tool to gain more leverage on the setscrew wrench . BLADE TI LT , OR SQUARENESS OF BLADE TO TABLE 90 ° ( SQUARE ) and 45 ° ( BEVEL ) STOP COLLARS . When the bevel _ inter is pointing directly to the " 0 " " markE on the bevel scale , the sawblade should make a SQUAR cut 90 ° to the table , To check for SQUARENESS : WARNING : FOR YOUR OWN SAFETY , TURN SWITCH " OFF " AND REMOVE PLUG FROM POWER SOURCE OUTLET . 1 . Raise blade all the way4JP . . , raise blade guard , 2 , TILT blade a few degrees to the LEFT . . . now tilt blade back to the RIGHT asfar as it wil go . 3 . Place the square against blade . Make sure square is not touching the TIP of one of the saw TEETH , 24
Page: 25

POINTERADJUSTNI G SCREW If bladeISSQUARE to table ; A . Check pointer ELEVATION HANDWHEEL If POINTER DOES NOT point to the " 0 " mark on the bevel scale ; B . Remove Elevation Handwheel C . Loosen screw and adjust pointer . . , using medium screwdriver . D , Install Elevation Handwheel POINTER BEVEL SCALE ADJUSTING SCREW BEVEL SCALE ADJUSTING SCREW If blade is NOT SQUARE to table . , , the 90 ° LIMIT STOP must be ADJUSTED . CAUTION : Cover blade with piece of cardboard to protect your hand . 1 . Using a small size screwdriver , reach UNDERNEATH saw and loosen BOTH setscrewsin 90 ° STOP COLLAR . NOTE : If you can't reach the setscrews , turn the TILT HANDWHEEL slightly . 2 . ROTATE the STOP COLLAR moving it away from pivot nut . 3 . TILT blade RIGHT or LEFT . . . checking with your square until blade is square to table . 4 . ROTATE STOP COLLAR moving it toward PIVOT NUT until it TOUCHES the PIVOT NUT . . . TIGHTEN the setscrews , 5 . Check POINTER , If it DOES NOT point to the " 0 ' " mark on the bevel scale . A . Remove Elevation Handwheel B , Loosen screw and adjust pointer . . . using medium screwdriver . PiVOt NUT C . Install Elevation Handwbeel 90 = STOP COLLAR TILT blade to LEFT as far as it will go . It will stop when the PIVOT NUT is against the 45 ° STOP COLLAR . A . Place an ACCURATE square against blade . Make sure square is not touching the TiP of one of the saw TEETH ; If blade is 45 ° to table ; A . Check pointer . If POINTER DOES NOT point to the 45 ° mark on the scale ; A . Loosen two screws on scale and adjust scale until POINTER points to 45 ° mark . If blade is NOT 45 ° to table . . . the 45 ° STOP COLLAR end SCALE must be ADJUSTED t . Remove Elevation Handwheel . 2 , Using a small size screwdriver , reach thru curved slot in front trim panel and loosen BOTH setscrews in 45 ° STOP COLLAR . NOTE : If you can't reach the setscrews , turn _ he TILT HAN DWH EEL slightly . 3 . ROTATE the STOP COLLAR moving it IN or OUT and TILT blade RIGHT or LEFT . . . checking with your square until blade is 45 ° to table . 4 _ TIGHTEN thesetscrgws _ NOTE : If you can't reach the setscrews , turn TILT HANDWHEEL slightly . 5 . Loosen two screws on scale and adjust scale until POINTER points to 45 ° mark . BACK OF SAW 6 . Install Elevation Handwheel . 25
Page: 26

STOP COLLAR BLADE ELEVATION SPACER When the elevation hendwheel is turned CLOCKWISE , until it stoos , the blade must not be more than two and one half 12 - 1 / 2 ) inches above the table . If the blade extends more than 2 - 1 / 2 inches , the motor could interfere with the underside of the table causing misalignment . ELEVATIC _ SCREW With the blade extending two and one half ( 2 - 1 / 2 ) inches PIVOT NUT above the table , the STOP COLLAR and SPACER must be SCREW against the ELEVATION SCREW PIVOT NUT . If the blade I extends more than two and one half inches , loosen two screws in STOP COLLAR , and readjust it , TILT SCREW TILT SCREW PIVOT NUT TILT AND ELEVATION MECHANISM ELEVATION HANDWHEEL ! The NANDWHEELS should turn freely without binding . The turning action can be adjusted by tightening or Ioosenlng the screws in the bearing retainer . Both handwheels must be removed to reach the adjusting screws . NOTE : When adjusting the screws on the TILT bearing ADJUST THESE retainer , hold the nut inside using a 3 / 8 in . wrench . The TWO SCREWS screws for the ELEVATION bearing retainer can be reached with a small screwdriver through the curved slot on the TILT front of the saw . dANDWHEEL ADJUST THESE TWO SCREWS MAINTENANCE WARNING : FOR YOUR OWN SAFETY , TURN SWITCH 2 . Rotate pawl Loward rear of spreader so that teeth are " OFF " AND REMOVE PLUG FROM POWER SOURCE above top of spreader . OUTLET BEFORE MAINTAINING OR LUBRICATING 3 . Hold spreader with left hand and place pawl over corner YOUR SAW . of workbench . Do not allow sawdust to accumulate inside the saw . 4 . Using a small rouna file ( Smooth Cul sharpen the Frequently blow out any dust that may accumulate inside teeth the saw cabinet and the motor . Frecluently clean your cutting tools with Craftsman Gum end Pitch Remover . A coat of automobile - type wax applied to the table will help to keep the surface clean and allow workpieces to slide more freely . If the Dowel cord s worn or cut . or damaged in any way , have it replaced immediately , Make sure tne teeth of the ANTIKICKBACK pawls are / always sharp , To sharpen : 1 Remove blade guard . 26
Page: 27

LUBRICATION The saw motor bearings have been packed at the factory 2 . Elevation screw threads and pivot nut . ( First Clean with with proper lubricant and require no additional lubrication . Craftsman Gum & Pitch Remover . ) The following parts should be oiled occasionally with SAE 3 . Cradle bearing points . No . 20 or No . 30 engine oil . 4 . Bearing points in guard assembly , miter gauge and ri _ ! . Tilt screw threads and pivot nut . ( First Clean with fence . Craftsman Gum & Pitch Remover . ) ELEVATION SCREW _ - ) / I ! = ' LEVATIONSCREW PIVOT NUT / \ TILT SGREW TILT SGREW PIVOT NUT RECOMMENDED ACCESSORIES ITEM CAT . NO . ITEM CAT . NO . Work Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 2481 Steel Legs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . g - 22235 Steel Stand . . : . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 22214 7 in . Dia . Adjustable Dado Head . . . . . . . . . . . . . . . 9 - 326 : 3 Retractable Caster Set . . . . . . . . . . . . . . . . . . . . . 9 - 22208 7 in . Dia . Dado Head . . . . . . . . . . . . . . . . . . . . . . . 9 - 3257 Solid Table Extension . . . . . . . . . . . . . . . . . . . . . . 9 - 29954 Sanding Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 2274 * 7 in , Molding Head Set . . . . . . . . . . . . . . . 9 - 3217 9 - 3218 Miter - Gauge Stop Rods . . . . . . . . . . . . . . . . . . . . . 9 - 29924 * 7 in , Molding Head . . . . . . . . . . . . . . . . . . . . . . . . 9 - 3214 Miter * Gauge Hold - Down Clamp . . . . . . . . . . . . . . 9 - 29928 Molding / Dado Insert for 7 in Taper Jig . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 3233 Dia . Molding or dado Head . . . . . . . . . . . . . . . . . . 9 - 29933 Universal Jig . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , 9 - 3231 " ' Power Tool Know How Handbook " Table Saw . . 9 - 291 ' , 3 Work Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 2480 The above recommended accessories are current and were available at the time this manual was printed . * Smaller Dia . Molding Heads cannot be used because they do not provide adequate depth of cut . 27
Page: 28

TROUBLE SHOOTING WARNING : FOR YOUR OWN SAFETY . TURN SWITCH " OFF " AND ALWAYS REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE TROUBLESHOOTING . TROUBLE SHOOTING - - GENERAL TROUBLE PROBABLE CAUSE REMEDY Excessive vibration . 1 . Blade out of balance . 1 . Discard Blade and use a different blade . Cannot make square 1 . 1 . Miter gauge not adjusted See " Adjustments " section " Miter Gauge . ' " Cut when crosscutting . properly , I . Cut binds , burns or 1 . Dul ! blade with improper Sharpen or replace blade . stalls motor when tooth set . 2 . ripping . 2 , Blade is Heeling . See " Adjustments " section , " Heeling Adjustment . . . " 3 . 3 . Warped board , Make sure concave or hollow side is facing " down , " feed slowly . 4 . 4 . Rip fence not parallel See " Assembly " section , " Aligning Rip Fence " to blade . 5 . Spreader out of 5 . See " Assembly " section , " Installing alignment Blade Guard . " Cut not true at 90 ° 1 . 1 , Stop collars not properly See " Adjustments " section , " Blade Tilt , or or 45 ° positions . adjusted , " Squareness of Blade to Table . " 1 , Sawdust on threads of tilt I . Tilt and elevating See " Maintenance and Lubrication " section , handwheels turn hard . screw or elevating screw . 2 . See " Maintenance " section 2 . Bearing retainers to tight . " ' Tilt and Elevation Mechanism . " TROUBLE SHOOTING - - MOTOR NOTE : Motors used on wood - working tools are particularly NOTE : The starting relay is a GRAVITY SENSITIVE susceptible to the accumulation of sawdust and wood chips TYPE . NEVER TURN THE POWER ON WHILE THE SAW and should be blown out or * ' vacuumed " frequently to IS UPSIDE DOWN AS THIS WILL DAMAGE THE prevent interference with normal motor ventilation . MOTOR . TROUBLE PROBABLE CAUSE REMEDY Excessive noise . 1 . Motor . 1 . Have motor checked by qualified service technician , Repair se _ ice is available at your nearest Sears store . Motor fails to develop 1 . Circuit overloaded with 1 , Do not use other appliances or motors on full power . ( Power lights , appliances and same circuit when using the saw , output of motor decreases other motors . rapidly with decrease in voltage at motor terminals . 2 . Undersize wires or circuit 2 . Increase wire sizes , or reduce length of wiring , For example , a reduction too tong . See " Motor Specification and Electrical of 10 % in voltage causes Requirements " section a reduction of 19 % in 3 , General overloading of 3 . Request a voltage check from the power company . maximum power output power company of which the motor is facilities , fin some capable , while a reduction sections of the of 20 % in voltage causes country , demand for a reduction of 36 % in electrical power may maximum power output , ) exceed the capacity of existing generating and distribution systems . ) 4 . Incorrect fuses or circuit 4 . Install correct fuses or circuit breakers . breakers in power line . 28
Page: 29

TROUBLE SHOOTING - - MOTOR ( Continued ) REMEDY TROUBLE PROBABLE CAUSE Motor starts slowly 1 . Low voltage will not 1 . Request voltage check from the power company . or fails to come up trip relay , 2 . Have motor repaired or replaced , to full speed . 2 . Windings burned out or open , 3 . Have relay replaced . 3 . Starting relay not operating . 1 , Motor overloaded . 1 . Feed work slower into blade . Motor overheats - 2 . Clean out sawdust to provide normal air 2 , Improper cooling . ( Air circulation restricted circulation through motor , See " Maintenance and Lubrication " section . through motor due to sawdust , accumulating inside of saw ) . 1 , Have relay replaced and request a voltage check Starting relay in 1 . Burned relay contacts from the power company . motor will not ( due to extended hold - in period , _ caused operate . by low line voltage , etc . ) 2 . Place saw in upright position . 2 . Saw not in upright position . 3 , Loose or broken 3 . Have wiring checked and repaired . connection _ 1 , Have relay replaced . Motor stalls 1 . Starting relay not operating . ( resulting in blown 2 . Request voltage check from the power company . fusesor tripped 2 . Voltage too low to permit circuit breakers ) . motor to reach operating speed . 3 . Install proper size fusesor circuit breakers . 3 . Fusesor circuit breakers do not have sufficient capaciw . 1 , Feed work slower into blade , 1 . Motor overloaded . Frequent opening of 2 . Install proper size fusesor circuit breakers . 2 . Fusesor circuit breakers fusesor circuit do not have sufficient breakers . capacity . 3 . Have relay replaced , 3 . Starting relay not operating ( motor does not reach normal speed ) . 29
Page: 30

PARTS LIST FOR CRAFTSMAN 10 INCH MOTORIZED SAW MODEL NO . 113.29570 & 113.295750 2 10 11 / ! / / 46 41 44 \ \ \ 38 45 \ o 42 43 / 49 \ \ 22 \ 17 18 23 20 21 19 34 33 32 38 37 l _ . _ 3s 3O 29 53 Figure 1
Page: 31

PARTS LIST FOR CRAFTSMAN 10 INCH MOTORIZED SAW MOD E L NO . 113.29570 & 113.295750 Always order by Part Number - not by Key Number FIGURE 1 PARTS LIST Key Part Key Part . No . No . No , No Description Description , , , , , , , , , , , 29 62709 Bar Assembly , Fence Guide 62714 1 Gauge Assembly , Miter ( See Figure 4 ) ( includes Key No . 28 ) 2 62715 Fence Assembly , Rip ( See Figure 3 ) STD 523115 30 * Screw , Hex 5 / 16 - 18 x 1 - I / 2 447441 Screw , Fiat Hd , Type " T " 10 - 32 x 7 / 8 3 31 eMotor and Control Box 62505 62514 Insert Assembly ( Includes Key No . 5 ) 4 62267 32 Clip , Capacitor 62545 5 Clip , Retaining 33 62442 Switch , Locking 62655 Guard Assembly ( See Figure 5 ) 6 34 60256 Key , Switch 7 62643 Clamp , Spreader 35 STD 551025 * Washer , 17 / 64 x . 734 x . 062 8 30540 Screw , Wing 1 / 4 - 20 x 1 / 2 36 60314 Screw , Truss 1 / 4 + 20 x 5 / 8 9 STD 551225 * Lockwasher , External Tooth 1 / 4 37 STD 551208 * Lockwasher , External Tooth No . 8 10 62642 Support , Spreader 38 STD 610805 Screw , Pan Hd + , Type " ' AB " No + 8 x 1 / 2 11 62636 * Nut , Square 1 / 4 - 20 39 STD 600602 * Screw , Type 23 , Pan Hd . , 6 + 32 x 1 / 4 52644 Bracket 12 40 62686 Scale , Adjustable Bevel 13 139331 Screw ; Set Hex Cup 1 / 4 - 20 x 7 / 8 41 62689 Handwheel Assembly 14 STD 551012 * Washer , t7 / 64 x 9 / 16 x 1 / ! 6 42 STD 511107 * Screw , Pan Hd . 10 - 32 x 3 / 4 15 STD541025 * Nut , Hex 1 / 4 - 20 43 STD 551210 * Lockwasher , External Tooth No , 10 16 STD 523110 Screw , Hex Hd . 5 / 16 ; 18 X 1 44 62713 Panel , Trim 17 62541 Bar , Fence Rear 45 6O354 Nut , Speed No . 8 18 60313 Nut , Self Threading 46 62712 Panel , Front 19 62542 Rod , Separation 47 62204 Clip , Cord 20 STD 551031 Washer , 21 / 64 x 5 / 8 x 1 / 16 48 STD 610802 * Screw , Pan Hd . , Type B , No . 8 x 5 / 16 21 STD 551231 * Lockwasher , External Tooth 5 / 16 49 62452 Clamp , Relay 22 STD 541231 * Nut , Hex , 5 / 16 - 18 5O 9TD 541025 Nut , Hex 1 / 4 - 20 23 6TD 600603 Screw , Type " T ' " Pan Hd . 6 - 32 x 3 / 8 51 3540 Wrench , Arbor 24 62441 Cord with Plug 52 63062 Wrench , Shaft 25 37818 Relief , Strain 53 30505 Wrench , Hex " L ' " 1 / 8 26 62652 Plate , Cover 37911 54 Wrench , Hex " L " 3 / 16 27 62539 Spacer , Fence Guide Bar 62717 Bag of Loose Parts ( Not Illustrated ) 28 62710 Tape , Fence 62716 Owners Manual ( Not Illustrated ) oAny attempt to repair this motor may create a HAZARD * Standard Hardware Item - - May be Purchased Locally . unless repair is done by a qualified service technician . Repair service is available at your nearest Sears Store .
Page: 32

PARTS LIST FOR CRAFTSMAN 10 INCH MOTORIZED SAW MODEL NO . 113.29570 & 113,295750 4 5 7 9 • 11 36 16 \ \ II 3 : 3 13 * if this part is removed . discard and reptace with a new relearningring , F _ ure 2
Page: 33

PARTS LIST FOR CRAFTSMAN 10 INCH MOTORIZED SAW MODEL NO . 113.29570 & 113.295750 FIGURE 2 PARTS LIST Key Part Key Part No . No . No . No , Description Description 23 62651 62628 Rod , Motor 1 Table , Saw 24 60076 2 805297 - 1 Screw , Fiat Hd . 5 / 16 - 18 x 1 - 1 / 4 I Washer , . 505x 1 - 1 / 8x 1 / 16 25 STD 541425 STD 511107 * Screw , Pan Hd . 10 - 32 x 3 / 4 * Nut , Lock I / 4 - 20 3 26 STD 551026 * Washer , 17 / 64 x . 734 x . 062 STD 541110 * Nut , Hex No . 10 - 32 4 27 8TD 541411 * Nut , Lock 10 - 32 5 STD 551210 * Lockwasher , External Tooth No . 10 28 STD 551031 * Washer , 21 / 64 x 3 / 4 x 1 / 16 6 62648 Washer , Rubber 29 8TD 523110 * Screw , Hex Washer 5 / 16 - 18 x 1 7 62629 Support , Rod 30 5TD 601103 8 62624 Rod , Cradle * Screw , Pan Hd . Type " ' T " 10 - 32 x 3 / 8 9 oMotor and Control Box 62505 31 62487 Lead with Eyelets 62498 Collar , Blade 10 32 62633 Base , Saw 11 62683 Collar , Stop L . H . 33 STD511105 Screw , Pan H & 10 - 32 x 1 / 2 12 60175 + Blade , Saw 10 inch 34 62685 Nut , Bevel Pivot 6362 13 Nut , Arbor 35 62684 Screw Assembly , Tilt 14 60303 Spacer 36 62437 Retainer , Bearing i5 62681 Nut , Elevation Pivot 37 STD 600803 * Screw , Type " ' T " Pan 8 - 32 x 3 / 8 60328 16 Washer , Nylon 38 62686 Indicator , Bevel 17 62647 Washer , Rubber 39 62436 Nut i8 STD 551037 * Washer , , 380 x 47 / 46 x 1 / 16 40 62625 Hanger 19 60301 * Ring , Retaining 3 / 8 41 62435 Washer , Thrust 20 62682 Screw Assembly , Elevation 42 62623 Cradle Assembly 21 62649 Grommet , Rubber 43 60052 * Screw , Fi ! lister Hd . 10 - 32 x 1 - 1 / 2 22 STD 511110 * Screw , Pan No . I0 - 32 x 1 * Standard Hardware Item - May be Purchased Locally , + Stock Item - May be secured through the hardware departments of most Sears Retail Stores or oAny attempt to repair this motor may create a HAZARD Catalog Order Houses . unless repair is done by a qualified service techincian . * If this part is removed , discard and Repair service is available at your nearest Sears Store . replace with a new retaining ring .
Page: 34

PARTS LIST FOR CRAFTSMAN 10 INCH MOTORIZED SAW MODEL NO , 113.29570 & 113.295750 10 il 4 5 6 / 12 3 13 17 FIGURE 3 - 62715 FENCE ASSEMBLY Key Part No . No . Description - - 62715 Fence Assembly , Rip 1 62693 Plug , Button 2 62692 Knob ( includes Key No . 1 ) 3 STD 551031 * Washer , 21 / 64 x 1 / 2 x 1 / 32 4 62711 Indicator , Fence 5 60049 _ Screw , Pan Hd . Type " ' T ' " 4 - 40x 3 / 16 6 62527 Head , Fence 7 423350 Screw , Sems 3 / 8 - 16 x 1 / 2 8 62526 Channel , Fence 9 STD 600805 Screw , Pan Hd . Type " T " 8 - 32 x 1 / 2 10 62528 Spring ; Fence Lock 11 62529 Lock , Rear Fence 12 62531 Roller , Rear Fence 13 62530 Rod , Fence Lock 14 62533 Spring , Head Alignment ( Includes Key No . 17 ) 15 STD 551210 * Lockwasher , External Tooth No . 10 16 STD 611005 * Screw , Type " A " Hex Hd . No ; 10 x I / 2 17 62532 Pad ; Alignment * Standard Hardware Item ' - May be Purchased Locally . 34
Page: 35

PARTS LIST FOR CRAFTSMAN 10 INCH MOTORIZED SAW MODEL NO , 113,29570 & 113.295750 12 11 9 10 FIGURE 4 - 62714 MITER GAUGE ASSEMBLY Part Key No , No , Description , , , , J - 62714 Miter Gauge Assembly 1 82683 P _ ug , Button 2 62692 Knob ( Includes Key No , 1 ) 3 STD 551031 * Washer , 21 / 64 × 1 x 1 / 16 4 37883 Gauge , Miter 5 STD 600803 * Screw , Pan Head Type " T " _ 32 X 5 / 16 6 STD551208 * Lockwasher ; External No . B 7 62042 Indicator 8 62252 Rod Asm , Miter Gauge { Includes Key No . 9 , I0 , 11 ) 9 62225 Stud , Clamp ! 0 STD541231 * Nut , Hex Jam 6 / 16 - 18 11 62383 Stud , Pivot 12 60288 Screw , Lockir _ Set 1 / 4 - 20 × 3 / 8 * t _ tandard Hardware Item - May be Purchased Locally . 35
Page: 36

PARTS LIST FOR CRAFTSMAN 10 INCH MOTORIZED SAW MODEL NO _ 113.29570 & 113 ; 295750 7 13 12 * i _ this part is removed , discard and replace with a new push nut . FIGURE 5 - - 62655 GUARD ASSEMBLY Key Part No . No , Description 62655 Guard Assembly 62415 Guard 1 62516 Pin 2 3 62650 Bumper , Snap In 4 STD 541425 * Nut , Lock 1 / 4 - 20 5 62517 Link , Guard 6 STD 512515 * Screw , Pan Hd . , 1 / 4 - 20 x 1 - 1 / 2 7 62522 Spacer ; Link 8 62656 Blade , Spreader 9 62410 Pin , 1 / 4 x 1 - 3 / 64 62519 10 Spring , Pawl 11 62520 Spacer , Pawl Pawl 12 62621 13 STD 651012 * Washer , 17 / 64 x 1 / 2 x 1 / 32 14 60297 * Nut , Push 15 STD 581025 * Ring , Retaining 1 / 4 * Standard Hardware Item - - May be Purchased Locally . 36
Page: 37

PARTS LIST FOR CRAFTSMAN 10 INCH MOTORIZED SAW MODEL NO . 113.29570 & 113.295750 4 5 3 6 5 4 2 1 1 2 \ 2 FIGURE 6 - MODEL 113.295750 ONLY Key Part . No . No Description I 60314 Screw , Serrated Truss Hd . 1 / 4 - 20 x 5 / 8 2 62552 Leg 3 62554 Stiffener , Side 4 STD 551225 * Lockwasher , Ext . 1 / 4 5 STD 541025 * Nut , Hex 1 / 4 - 20 6 62553 Stiffener , End 7 STD 541250 * Nut , Hex 1 / 2 - 13 8 803835 Foot , Leveling 62659 tBeg of Loose Parts ( not illustrated ) * Standard Hardware Items - May be Purchased Locally , t Bagcontains all Loose Parts for both Legsand Extensions 37
Page: 38

PARTS LIST FOR CRAFTSMAN 10 INCH MOTORIZED SAW MODEL NO . 113.29570 & 113.295750 2 1 I SAW TABLE \ { REF ) 11 , % FIGURE 7 - - TABLE EXTENSION FOR MODEL 113.295750 ONLY Part No , No , Description . , , , , , , , , , . , . . - - 62546 Extension Assembly , Complete Screw , Serrated Truss Hd . 1 / 4 - 20 x 1 " 1 t 60323 2 62547 Extension 3 ! 62549 Bracket , CornerSupportNo , 2 1 4 62548 Bracket , Corner Support No . 1 5 STD 541025 * Nut , Hex 1 / 4 - 20 6 STD 551225 * Lockwasher t Ext . I / 4 7 62550 Bracket , Corner Stiffener HARDWARE FOR ATTACHING EXTENSION TO TABLE * Screw , Hex Hal . 5 / 16 - 18 X I - I14 8 STD523112 * Washer , 1 ! / 32 x 11 / 1 6 x 1 / 16 9 STD 551031 * Lockwasheri Ext . 5 / 16 10 STD 551131 * ' Nut , Hex 5 / 16 - 18 11 STD541031 fBag of Loose Parts ( not illustrated ) 62659 * Standard Hardware Item - May be Purchased Locally . 1 " Begcontains atl Loose Parts for both Legs and Extension . 38
Page: 39

NOTES 39
Page: 40

Sears I owners 10 INCH MOTORIZED TABLESAW manual SERVICE Now that you have purchased your 10 inch motorized table saw should a need ever exist for repair parts or service , simply contact any Sears Service Center and most Sears , Roebuck and Co . stores . Be sure to provide all pertinent facts when you call or visit . MODEL NO . 113.29570 SAW ONLY The model number of your 10 inch motorized table saw will be 113.295750 found on a plate attached to your saw , at the right - hand side of the base . SAW WITH LEGS AND TWO TABLE EXTENSIONS HOW TO ORDER WHEN QRDERING REPAIR PARTS , ALWAYS GIVE THE FOLLOWING INFORMATION : REPAIR PARTS PART NUMBER PART DESCRIPTION MODEL NUMBER NAME OF ITEM 113,29570 IO - INCH MOTORIZED TABLE SAW 113.295750 All parts listed may be ordered from any Sears Service Center and most Sears stores . If the parts you need are not stocked locally , your order will be electronically transmitted to a Sears Repair Parts Distribution Center for handling . Sold by SEARS , ROEBUCK AND CO . . Chicago . IL . 60684 U . S , A . PartNo . 62716 Form No . SP4319 - 1 Printed in U . S . A . 7 / 79
Search in Table Saw on ebay
"