Home | Register Login | Wanted Manuals | MarketPlace | Members Area | Manuals Manufacturer Directory | UPC Lookup | Information Pages | Policy


Back To Craftsman Table Saw       Model: 113.298141 or 113298141 Craftsman 10 Inch Table Saw
Regular Text Search or Search by Model Number

Register / log-in to add to your Hammerwall Collection.
Manual Location


This is a partial text extraction from the pdf, to download the pdf, click the Manual tab. If you want to search this text, hold control and F, and type the word you are looking for.

Page: 1

[ Sears ! owners manual MODEL NO . 113.298141 SAW ONLY 113.298031 SAW WITH LEGS TWO TABLE EXTENSIONS AND MOTOR 113.298151 SAW WITH LEGS ONETABLEEXTENSION AND MOTOR Serial Number . Model and serial number may be found at the left - hand side of the base . You should record both model and serial number in a safe place for future use . IO - INCH TABLE SA IN CAUTION : • assembly Read GENERAL and ADDITIONAL • operating SAFETY INSTRUCTIONS • repair parts carefully Sold by SEARS , ROEBUCK AND CO . , Chicago , IL . 60684 U . S . A . Part No . 62753 Printed n U . S . A .
Page: 2

3 FULL ONE YEAR WARRANTY ON CRAFTSMAN TABLE SAW If within one year from the date of purchase , this Craftsman Table Saw fails due to a defect in material or workmanship , Sears will repair it , free of charge . WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS STORE OR SERVICE CENTER THROUGHOUT THE UNITED STATES . This warranty givesyou specific legal rights , and you may also have other rights which vary from state to state . SEARS , ROEBUCK AND CO . , Sears Tower , BSC 41 - 3 , Chicago , IL 60684 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS 1 . KNOW YOUR POWER TOOL protectors ( plugs or muffs ) during extended periods of Read and understand the owner's manual and labels operation . affixed to the tool . Learn its application and limitations as well as the specific potential hazards 13 . SECURE WORK peculiar to this tool . Use clamps or a vise to hold work when practical , It's 2 . GROUND ALL TOOLS safer than using your hand , frees both hands to operate tool . This tool is equipped with an approved 3 - conductor cord and a 3 - prong grounding type plug to fit the 14 . DON'T OVERREACH proper grounding tvPe receptacle . The green conductor Keep proper footing and balance at all times , in the cord is the grounding wire . Never connect the green wire to a live terminal . 15 . MAINTAIN TOOLS WITH CARE 3 . KEEP GUARDS IN PLACE Keep tools sharp and clean for best and safest performance . Follow instructions for lubricating and in working order , and in proper adjustment and changing accessories . alignment . 4 . REMOVE ADJUSTING KEYS 16 . DISCONNECT TOOLS AND WRENCHES before servicing ; when changing accessories such as blades , bits , cutters , etc . Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on . 17 . AVOI D ACCl DENTAL STARTING 5 . KEEP WORK AREA CLEAN Make sure switch is in " OFF " position before plugging Cluttered areas and benches invite accidents , Floor in . must not be slippery due to wax or sawdust . 18 . USE RECOMMENDED ACCESSORIES 6 . AVOID DANGEROUS ENVIRONMENT Consult the owner's manual for recommended Don't use power tools in damp or wet locations or accessories , Follow the instructions that accompany expose them to rain . Keep work area well lighted . the accessories . The use of improper accessories may Provide adequate surrounding work space . cause hazards . 7 . KEEP CHILDREN AWAY 19 . NEVER STAND ON TOOL All visitors should be kept a safe distance from work Serious injury could occur if the tool is tipped or if the area . cutting tool is accidentally contacted . 8 . MAKE WORKSHOP KID - PROOF Do not store materials above or near the tool such that - - with padlocks , master switches , or by removing it is necessary to stand on the tool to reach them , starter keys . 20 . CHECK DAMAGED PARTS 9 . DON'T FORCE TOOL It will do the job better and safer at the rate for which Before further use of the tool , a guard or other part that it was designed . is damaged should be carefullv checked to ensure that it 10 . USE RIGHT TOOL will operate properly and perform its intended function . Check for alignment of moving parts , binding of moving Don't force tool or attachment to do a job it was not parts , breakage of parts , mounting , and any other designedfor . conditions that may . affect its operation . A guard or 11 . WEAR PROPER APPAREL other part that is damaged should be properly repaired Do not wear loose clothing , gloves , neckties or jewelry or replaced . ( rings , wrist watches ) to get caught in moving parts . Nonslip footwear is recommended . Wear protective 21 . DIRECTION OF FEED hair covering to contain long hair . Roll long sleeves above the elbow . Feed work into a blade or cutter against the direction 12 . USE SAFETY GOGGLES ( Head Protection ) of rotation of the bladeor Cutter only . Wear Safety goggles ( must comply with ANSI Z87 . 1 ) 22 . NEVER LEAVE TOOL RUNNING at all times . Everyday eyeglasses only have impact UNATTENDED resistant lenses , they are NOT safety glasses , Also , use Turn power off , Don't leave tool until it comes to a face or dust mask if cutting operation is dusty , and ear complete stop .
Page: 3

ADDITIONAL SAFETY INSTRUCTIONS FOR TABLE SAWS WARNING : FOR YOUR OWN SAFETY , DO NOT ( sawing entirelv thru the work ) AND by removmg OPERATE YOUR SAW UNTIL IT IS COMPLETELY a loose pieces from the table with a long stick of ASSEMBLED AND INSTALLED ACCORDING TO THE wood IMMEDIATELY after they are cut off . INSTRUCTIONS . . . AND UNTIL YOU HAVE READ D . Use extra caution when the guaro assembly is AND UNDERSTOOD THE FOLLOWING . removea for resawing , dadoing , rabbeting , or 1 . GENERAL SAFETY INSTRUCTIONS FOR POWER molding - replace the guard as soon as tna _ TOOLS . . . SEE PAGE 2 operation is completed . 2 . GETTING TO KNOW YOUR SAW . . . SEE PAGE 20 E . For rip or rip - type cuts . the following end of a 3 . BASIC SAW OPERATION . . . SEE PAGE 23 workoiece to which a push stick or push board is 4 . ADJUSTMENTS . . . SEE PAGE 29 applied must be square ( perpendicular to the fence ) 5 . MAINTENANCE . . . SEE PAGE 32 in order that feed pressure applied to the workpiece 6 . STABILITY OF SAW by the push stick or block does not cause the If there is any tendency for the saw to tip over or move workpiece to come away from the fence , and durmg certain cutting ooerations such as cutting possibly cause a kickback . extremely large heavy panels or long heavy boards , the F . During rip and rip type cuts , the workpiece must be saw should be bolted down . held down on the table and against the fence with a If you attach any kind of table extensions over 24 " push stick , push block , or featherhoaros . A wide to either end of the saw , make sure you either bolt feather board is made of solid lumber per sketch . the saw to the bench or floor as a I _ propriate , or support _ S " the outer end of the extension from the bench or floor , KERF ABOUT as appropriate . 7 . LOCATION The saw should be positioned so neither the operator nor a casual observer s forced to stand in line with the saw blade . G . NEVER turn the saw " ON " before clearing the 8 . KICKBACKS [ able of all tools , wood scraps , etc . , except the Kickbacks can cause serious injury : A " Kickback ' " workoiece and _ elateo feed or suoport devices for occurs when a 0art of the workpiece binds between the [ he operation planned . sawblade and the rid fence or other fixed object , rises H . NEVER place your face or body n line with the from the table , and is thrown toward the operator . cutting toot . Keep your face and body to one side of the sawblade , I NEVER place your fingers or hands ir the path of out of line with a possible " Kickback . ' " the sawblade or other cutting tool . Kickbacks - and possible injury from them - - can J . NEVER reach in back of the cutting tool with usually be avoided oV : either hand to hold down or support the workmece , A . Maintaining the rip fence parallel to the sawblade . remove wood scraps , or for any other reason . Avoid B . Keeping the sawblade sharp , Replace or sharpen awkward operations and hand positions where a antikickback pawls when points become dull . sudden slib could cause fingers or hand to move C . Keeping sawblade guard , spreader , and antikickback into a sawblade or other cutting tool . pawls in place and operating properly . The spreader K . DO NOT perform layout , assembly , or setup work must be in alignment with the sawblade and the on the table while the cutting tool is rotating . pawls musl stop a kickback once it has started . L . DO NOT perform any operation " FREEHAND " - Check their action before ripping , always use either the rip fence or the miter gauge to D . NOT ripping work that is twisted or warpea or does position and guide the work . not have a straight edge to guide along the rip fence . M . NEVER use the rip fence when crosscutting or the E . NOT releasing work until you have pushed it al ! the mtter gauge when ripping , DO NOT use the rid way past the sawblade . fence as a length stop . F . Using a push stick for ripping widths of 2 to 6 in . , Never hold onto or touch the " free end " of the ana an auxiliary fence ana push block for ripping workpiece or a " free piece " that is cut off , while widths narrower than 2 q . ( See " Basic Saw power _ s " ON " and / or the sawblade is rotating . Operation Using The Rip Fence " section . _ N . Shut " OFF " the saw and disconnect the power core G . NOT confining the cut - off oiece when ripping or whet removing the table insert , changing the cross - cutting . cutting tool , remowng or replacing the blade guard . H . When ripping apply the feed force to the section of or making adjustments . the workpiece between the saw blade and the rip O . Provide adectuate support to the rear and s _ des of fence . the saw table for wider or long worKpiece's . 9 . PROTECTION : EYES , HANDS , FACE , EARS , BODY P . Plastic and composition ( like hardboard ) materials P _ If any oar [ of your saw is malfunctioning , has been may oe cut on your saw . However , since these are damaged or broken . . SUCh as the motor switch , or usually quite hard and slippery , the antikickback other operating control , a safety device or the pawls may not stop a kickback . power cord . . cease opera [ rag immediately until Therefore , be especially attentive to following the particular part s properlv repaired or rep aced . proper set - up and cutting procedures for ripping . B . Wear safety goggles that comply with ANSI Z87 . 1 , Do not stand , or permit anyone else to stand , in line and a face shield if operation is dusty , Wear ear with a potential kickback . plugs or muffs during extended periods of Q . If you stall or jam the sawblade in the workolece , operation . turn saw " OFF " , remove the worKpiece from the sawblade , and check to see f the sawblade s C . Small loose pieces of wood or other objects [ hat parallel to the miter gauge grooves and i _ the contact the rear of the revolving blade can be spreader is in proper alignment with the sawblade . thrown back at the operator at excessive soeed . This If ripping at the time , check to see if the rip fence is can usualtv be avoided by keeping the guard and parallel with the sawblade . Readjust as indicated . spreader in place for all thru - sawing operations
Page: 4

R . DO NOT remove small ; ) ieces of cut - off material efficiency when ripping , use the maximum diameter that may become trapped inside the blade guard blade for which the saw is designed , since under these while the saw is running . This could endanger your conditions the spreader is nearest the blade . hands or cause a kickback . Turn saw " OFF " and 15 . AcIjust table inserts flush with the table top . NEVER wait until blade stops . operate the saw unlessthe proper insert is installed . S . Use extr _ care when ripping wood that has a twisted 16 , NEVER feed material into the cutting tool from the grain or is twisted or bowed it may rock on the rear of the saw . An accident and serious injury could table and / or pinch the sawblade . result . 10 . KNOW YOUR CUTTING TOOLS 17 . THINK SAFETY . A Dull , gummy , or improperly sharpened or set cutting Safety m a combination of operator common sense and tools can cause material to stick , jam , stall the saw , alertness at all times when the saw is being used . or kickback at the operator . 18 . NOTE AND FOLLOW SAFETY INSTRUCTIONS Minimize potent / a injury by proper cutting tool THAT APPEAR ON THE FRONT OF YOUR SAW . and machine maintenance . NEVER ATTEMPT TO FREE A STALLED DANGER FOR YOUR OWN SAFETY SAWBLADE WITHOUT FIRST TURNING THE READ AND UNDERSTAND OWNER'S MANUAL SAW OFF BEFORE OPERATING MACHINE : B , Never use grinding wheels , abrasive cut - off wheels , 1 WEAR SAFETY GOGGLES PER ANSI Z87 . 1 AT ALL friction wheels ( metal slitting blades ) wire wheels or TIMES buffing wheels . 2 . USE SAW - BLADE GUARD FOR " THRU - SAWING ' " 11 . USE ONLY ACCESSORIES DESIGNED FOR THIS 3 , KEEP HANDS OUT OF PATH OF SAWBLADE 4 , USE A " PUSH - STICK " WHEN REQUIRED SAW 5 , KNOW HOW TO AVOID " KICKBACKS " 12 . Crosscutting operations are more conveniently worked 6 DO NOT PERFORM OPERATIONS " FREEHAND " and with greater safety if an auxiliary wood facing is 7 , NEVER REACH AROUND OR OVER SAW BLADE attached to the miter gauge using the holes provided However , the facing must notinterfere with the proper 19 . WARNING : DO NOT ALLOW FAMILIARITY functioning of the sawblade guard . ( GAINED FROM FREQUENT USE OF YOUR SAW ) 13 . Make sure the top of the arbor or cutting tool rotates TO BECOME COMMONPLACE . ALWAYS toward you when standing in normal operating REMEMBER THAT A CARELESS FRACTION OF A position . Also make sure the cutting tool , arbor collars SECOND IS SUFFICIENT TO INFLICT SEVERE and arbor nut are installed properly . Keep the cutting INJURY . tool as low as possible for the operation being 20 . WARNING : THE 2 - 1 / 2 " SAW PULLEY AND THE performed . Keep all guards in place whenever possible , 2 - 1 / 2 " MOTOR PULLEY FURNISHED , WILL RUNPM 14 . Do not use any blade or other cutting tool marked for THE BLADE AT APPROXIMATELY 3450 R an operating speed less than 3450 RPM . Never use WHEN USED WITH A 3450 RPM MOTOR . NEVER cutting tool larger in diameter than the diameter for SUBSTITUTE THESE PULLEYS TO INCREASE THIS which the saw was designed . For greatest safety and SPEED BECAUSE IT COULD BE DANGEROUS . The operation of any power tool can result in foreign objects being thrown into the eyes , which can result in severe eye damage . Always wear safety goggles complying with ANSI Z87 . 1 ( shown on Package ) before commencing power too ] operation . Safety Goggles are available at Sears retail or catalog stores . MOTOR SPECIFICATIONS AND ELECTRICAL REQUIREMENTS This saw is designed to use a 3450 RPM motor only . Do not CONNECTIN G TO POWER SOURCE OUTLET use any motor that runs faster than 3450 RPM . It is wired This saw must be grounded while in use to protect the for operation on 110 - 120 volts , 60 Hz . , alternating current . operator from electrical shock . IT MUST NOT BE CONVERTED TO OPERATE ON 230 If power cord is worn or cut , or damaged in any way , have VOLTS . EVEN THOUGH SOME OF THE it replaced immediately . RECOMMENDED MOTORS ARE DUAL VOLTAGE . If your saw is for use on less than 150 volts it has _ l _ lug Changing to _ 0 volt will not conserve energy and requlrcs that looks like below . changing the power cord plug . 3 - PRONG PLUG The outlet in the switch box will accept either a 15 an " _ . or a 20 amp . motor plug . RECOMMENDED CRAFTSMAN MOTORS FOR USE ON THIS SAW . H . P . R . P . M . Volts Catalog No . 1 3450 11 _ 120 1217 \ GROUNDING PRONG 1 3450 110 - 120 1220 _ " PROPERLY GROUNDED CAUTION : Do not use blower or washing machine motors 3 - PRON G OUTLET or any motor with an automatic reset overload protector as their use may be hazardous .
Page: 5

Plug power cord into 110 - 120V properly grounded type GROUNDING LUG outlet protected by a 15 - amp . time delay or Circuit - Saver fuse or circuit breaker , IF YOU ARE NOT SURE THAT YOUR OUTLET IS PROPERLY GROUNDED , HAVE IT CHECKED BY A QUALIFIED ELECTRICIAN . \ / 3 - PRONG CONNECTED TO A WARNING : DO NOT PERMIT FINGERS TO TOUCH THE TERMINALS OF PLUG WHEN INSTALLING OR REMOVING THE PLUG TO OR FROM THE OUTLET . 2 - PRONG RECEPTACLE WARNING : IF NOT PROPERLY GROUNDED THIS POWER TOOL CAN INCUR THE POTENTIAL HAZARD OF ELECTRICAL SHOCK , PARTICULARLY WHEN NOTE : The adapter illustrated is for use only if you already USED IN DAMP LOCATIONS , IN PROXIMITY TO have a properly grounded 2 - prong receptacle . PLUMBING , OR OUT OF DOORS . IF AN ELECTRICAL The use of any extension cord will cause some loss of SHOCK OCCURS THERE IS THE POTENTIAL OF A power . To keep this to a minimum and to prevent SECONDARY HAZARD SUCH AS YOUR HANDS over - heating and motor burn - out , use the table below to CONTACTING THE SAWBLAD E . determine the minimum wire size ( A . W . G . ) extension cord . This saw is equipped with a 3 - conductor cord and Use only 3 wire extension cords which have 3 prong grounding type plug which has a grounding prong , approved grounding type plugs and 3 - pole receptacles which will by Underwriters ' Laboratories and the Canadian Standards accept the _ fug on the saw . Association . The ground Conductor has a green lug and is attached to the tool housing at one end and to the ground 1 H . P . MOTOR 110 - 120V prong in the attachment plug at the other end . Extension Cord Length Wire Size A . W . G . This plug requires a mating 3 - conductor grounded type Upto 50 Ft . . . . . . . . . . . . . . . . . 14 outlet as shown . 50to 100 Ft . . . . . . . . . . . . . . . . 12 If the outlet you are planning to use for this saw is of the 100 - 200 Ft . . . . . . . . . . . . . . . . . 10 two prong type DO NOT REMOVE OR ALTER THE 200 - 400 Ft . . . . . . . . . . . . . . . . . 8 GROUNDING PRONG IN ANY MANNER . Use an adapter as shown and always connect the grounding lug to a known ground . CHECK MOTOR ROTATION It is recommended that you have _ qualified electrician WARNING : FOR YOUR OWN SAFETY , MAKE SURE replace the TWO prong outlet with a ; ) roperly grounded PLUG IS NOT CONNECTED TO POWER SOURCE THREE prong outlet . OUTLET . WHEN CHANGING MOTOR ROTATION . An adapter asshown below is available for connecting plugs The motor must rotate CLOCKWISE when viewed from the to 2 - prong receptacles . The green grounding lug extending shaft end to which you will mount the pulley . ( See page from the ads pter must be connected to a permanent ground 16 . ) If it does not , change the direction according to the instructions furnished with the motor . such asto a properly grounded outlet box . CONTENTS WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Miter Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Blade Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 GENERAL SAFETY INSTRUCTIONS Table Insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 FOR POWER TOOLS . . . . . . . . . . . . . . . . . . . . . . . . . 2 Removing and Installing Sawblade . . . . . . . . . . . . . . . 22 ADDITIONAL SAFETY INSTRUCTIONS Exacti - Cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 FOR TABLE SAWS . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BASIC SAW OPERATION USING THE MITER GAUGE23 MOTOR SPECl FICATIONS AND ELECTRICAL Work Helpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Crosscutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 UNPACKING AND CHECKING CONTENTS . . . . . . . . 6 Repetitive Cutting . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Tools Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Miter Cutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 List of Loose Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Bevel Crosscutting . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Compound Miter Cutting . . . . . . . . . . . . . . . . . . . . . . 25 Installing Handwheels . . . . . . . . . . . . . . . . . . . . . . . . . 7 BASIC SAW OPERATION USING THE RIP £ ENCE . . 26 Checking Table Insert . . . . . . . . . . . . . . . . . . . . . . . . . 7 Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Checking Blade Squareness to Table . . . . . . . . . . . . . . 8 Bevel Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Assembling Steel Legs . . . . . . . . . . . . . . . . . . . . . . . . . 8 Resawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Mounting Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Cutting Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Attaching Table Extensions . . . . . . . . . . . . . . . . . . . . . 9 Rabbeting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Installing Rip Fence Guide Bars . . . . . . . . . . . . . . . . . 10 ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Aligning Rip Fence . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Miter Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Adjusting Rip Scale Pointer . . . . . . . . . . . . . . . . . . . 13 Heeling Adjustment or Parallism of Installing Blade Guard . . . . . . . . . . . . . . . . . . . . . . . . 14 Sawblade to Miter Gauge Groove . . . . . . . . . . . . . . . 29 Mounting th _ Motor . . . . . . . . . . . . . . . . . . . . . . . . . 16 Blade Tilt , or Squareness of Installing Belt Guard . . . . . . . . . . . . . . . . . . . . . . . . . 18 Blade to Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Plugging in Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Tilt Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 GETTING TO KNOW YOUR SAW . . . . . . . . . . . . . . . 20 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 On - Off Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 LUBRICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Elevation Handwheel . . . . . . . . . . . . . . . . . . . . . . . . . 21 Tilt Handwheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 RECOMMENDED ACCESSORIES . . . . . . . . . . . . . . . . 33 Tile Lock Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . 34 Rip Fence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 REPAI R PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Page: 6

UNPACKING AND CHECKING CONTENTS COMBINATION SQUARE MUST BE TRUE . TOOLSNEEDED STRAIGHT EDGE OF I _ OARD 3 / 4 ' 1 THICK . THIS EDGE MUST BE PERFECTLY STRAIGHT . DRAW LIGHT LINE ON BOARD ALONG THIS EDGE . _ ' _ \ Medium Screwdriver Small Screwdriver Pi , e , , Wrenche I , I . : , : I ' , I . III _ ' Zi , _ 3 / 8 in . 7 / 16 in . 1 / 2 in . 9116 in . SHOULD BE NO GAP OR OVERLAP HERE WHEN SQUARE IS FLIPPED Combination Square 3 / 4 in . OVER IN DOTTED POSITION . Model 113,298141 Table Saw is shipped complete in one LIST OF LOOSE PARTS carton but DOES NOT INCLUDE Table Extension , Steel Legs , or motor . Item Part Name Qty . Model 113.298031 Table Saw is shipped complete n one carton but INCLUDES Two Table Extensions , Steel Legs , A Blade GuardandSpreader . . . . . . . . . . . . . . . . . . and Motor . B Rip Fence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C OwnersManual . . . . . . . . . . . . . . . . . . . . . . . . . . Model 113.298151 Table Saw is shipped complete in one carton but INCLUDES One Table Extension , Steel Legs , D Miter Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E Arbor Nut Wrench * . . . . . . . . . . . . . . . . . . . . . . . and Motor . F Switch w ! Key . . . . . . . . . . . . . . . . . . . . . . . . . . . Separate all parts from packing materials and check each G Rip FenceGuide Barwith Rip Scale ( Front ) . . . . one with the illustration and the list of Loose Parts to make H Handwheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . certain all items are accounted for , before discarding any J V - Be , t 1 / 2 in . x41 in . * . . . . . . . . . . . . . . . . . . . . packing material . K Pulley , 2 - I / 2 in . dia . , with 5 / 8 in . bore * . . . . . . . If any parts are missing , do not attempt to assemble the L Belt andPulley Guard . . . . . . . . . . . . . . . . . . . . . table saw , plug in the power cord or turn the switch on M Belt GuardClip . . . . . . . . . . . . . . . . . . . . . . . . . . until the missing parOs are obtained and are installed N Self - ThreadingScrew . 10 - 32 x 1 / 2 in . long . . . . . correctly . 0 Belt GuardSupport . . . . . . . . . . . . . . . . . . . . . . . Remove the protective oil that is applied to the table top P Belt GuardSupport Bracket . . . . . . . . . . . . . . . . and edges of the table . Use any ordinary household type Q Motor Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . grease and spot remover . R SpreaderRod * . . . . . . . . . . . . . . . . . . . . . . . . . . S Blade GuardSupport with Screw * , . . . . . . . . . . CAUTION : Never use gasoline , naptha or similar highly volatile solvents . T SpreaderSupport * . . . . . . . . . . . . . . . . . . . . . . . U Rip FenceGuide Bar ( Rear ) . . . . . . . . . . . . . . . . Apply a coat of automobile wax to the table . V Rip FenceGuide Bar Rod . . . . . . . . . . . . . . . . . . Wipe all parts thoroughly with a clean , dry cloth . * Pkg , of MiscellaneousSmall PartsNo . 62751 WARNING : FOR YOUR OWN SAFETY NEVER Consistingof the Following : CONNECT PLUG TO POWER SOURCE OUTLET UNTIL W SetscrewWrench , 3 / 32 in . . . . . . . . . . . . . . . . . 1 ALL ASSEMBLY STEPS ARE COMPLETE , AND YOU W SetscrewWrench , 1 / 8 in . . . . . . . . . . . . . . . . . . 1 HAVE READ AND UNDERSTAND THE SAFETY AND W SetscrewWrench , 5 / 32 in . . . . . . . . . . . . . . . . . 1 OPERATIONAL INSTRUCTIONS . X Self - ThreadingHut . . . . . . . . . . . . . . . . . . . . . 2 Y Hex HeadScrew , 5 / 16 - 18 x 1 - 3 / 4 in . long . . . 2 Y Hex HeadScrew , 5 / 16 - 18 x 5 / 8 in . long . . . . 3 Y Hex HeadScrew , 5 / 16 - 18 x 1 in . long . . . . . . 4 Y Hex HeadScrew , 1 / 4 - 20 x 518in . long . . . . . 2 Y Hex HeadScrew , 5 / 16 - 18 x 3 / 4 in . long . . . . . . 1 * These partsare packagedin LooseParts BagNo . 62750 SIL _ X Y \ G 3 / 4 Z AA AC \ / AB _ LE _ NGTH ( _ AD AG K
Page: 7

ItemParNt ame Qty . Z HexNut , 5 / 16 - 18 A ( approx . dia . of hole 5 / 16 in . ) . . . . . . . . . . . 9 Z Hex Nut , 1t4 - 20 ( approx . dia . of hole 114in . ) . . . . . . . . . . . . 2 AA Lockwasher , 5 / I 6 in . ExternalType ( approx . die . of hole 5116in . ) . . . . . . . . . . . 11 AA Lockwasher1 , / 4 in . ExternalType ( approx . alia . of h ale 1 / 4 in . ) . . . . . . . . . . . . 2 AA LockwasherNo . 10 ExternalType ( approx . dia . of hole3t16 in . ) . . . . . . . . . . . 1 © AB CarriageBolt , 5 / 16 - 18 x 3 / 4 in . long . . . . . . . 4 G H AC Rip FenceGuideBarSpacer . . . . . . . . . . . . . . 2 AD Wire Tie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 F AE Thumbscrew5 , / 1G - 18x 1 in . long . . . . . . . . . . 1 AF Screw PanHd . 10 - 32 x 3 / 4 . . . . . . . . . . . . . . 1 AG Flat Washer ( dia . of hole 21 / 64 ) . . . . . . . . . . . 2 J K L The followingpartsareincludedwith Model113 . 298031 and Item Pert Name Qty . 113.298151 . K TrussHeadScrew , 1 / 4 - 20 x 5 / 8 in . long A Leg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 8 SideStiffener . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ( top of screwisrounded ) . . . . . . . . . . . . . . . . 24 L C EndStiffener . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Leveling Foot . . . . . . . . . . . . . . . . . . . . . . . . . 4 D TableExtension ( 113.298031 ) . . . . . . . . . . . . . . 2 Pkg . of MiscellaneouSsmall PartsNo . 62745 for TableExtension ( 113.298151 ) . . . . . . . . . . . . . . I TableExtensions ( 1 ea . for Model113 . 298151 , E Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I 2 ea . for Model 113.298031 ) Pkg . of Miscellaneou _ small Parts , No . 62752for Legs Consistingof the following : Consistingof the Following : F Hex Hd , Screw , 5 / 16 - 18 x I - 1 / 4 in . long . . . . . 4 F Hex HeadScrew5116 - 18 x 1 - 1 / 4 in . long . . . . 4 , G LockwasherE , xternalType G Lockwasher1 , / 4 in . ExternalType ( approx . dia . of hole 1 / 4 in . ) . . . . . . . . . . . . . . 8 ( approx . dia . of hole1 / 4 in . ) . . . . . . . . . . . . . . 24 G Lockwasher , ExternalType ( approx . dia . of hale5 / 16 in . ) . . . . . . . . . . . . . 4 G Lockwasher5 , / 16 in . ExternalType H Hex Nut , 1 / 4 - 20 ( epprox . dia . of hole 5 / 16 in . ) . . . . . . . . . . . . 4 H Hex Nut , 1 / 4 - 20 ( approx . alia . of hole114in . ) . . . . . . . . . . . . . . 8 ( approx . dia . of hole 1 / 4 in . ) . . . . . . . . . . . . . 24 H Hex Nut , 5 / 16 - 18 H Hex Nut , 5 / 16 - 18 ( approx . dia . of hole5 / 16 in . ) . . . . . . . . . . . . . . 8 ( approx . dia . of hole5 / 16 in . ) . . . . . . . . . . . . . 4 K TrussHeadScrew , 1 / 4 - 20 x 1 in . long H Hex Nut , 1 / 2 - 13 ( top of screwisrounded ) . . . . . . . . . . . . . . . . 8 M Corner _ ; tiffener Bracket . . . . . . . . . . . . . . . . . . 2 ( approx . dia . of hole1 ] 2 in . ) . . . . . . . . . . . . . 8 N CornerSupportBracket . . . . . . . . . . . . . . . . . . 2 J FlatWasher ( dia . of hole , 11 / 32 in . ) . . . . . . . . . . 8 ASSEMBLY Before mounting the saw on legs , a stand or a bench , the Table Insert and Blade Squareness must be checked at this time . LOCKWASHER / INSTALLING HANDWHEELS 1 . Line up FLAT SPOTS on shaft and hardwheel , push handwheel onto shaft . Install screw and Iockwasher to lock handwheel on shaft . 10 - 32 X 3 / 4 IN . ELEVATION PAN HEAD SCREW / HANDWHEEL TILT HANDWHEEL CHECKING TABLE INSERT 2 . Insert should be flush with table top . Check as shown . Loosen flat head screw that holds insert and adjust the four set screws as necessary . Tighten flat head screw . \ Do not tighten screw to the point where it deflects the TABLE INSERT insert . 3 / 32 I N . SETSCREWWRENCH
Page: 8

To remove insert . A ) Loosen Screw B ) Lift insert from front end , and pull toward front of saw , 4 . To replace insert . Place insert into insert opening in table and push toward rear of saw to engage spring clip and until keyslot in insert will drop over screw . Tighten screw . Do not tighten screw to the point where it will deflect the insert . CHECKING BLADE SQUARENESS TO TABLE IMPORTANT : BLADE must be SQUARE ( g0 ° ) to TABLE , in order to proceed with assembly . To check for blade squareness , refer to " BLADE TILT , OR SQUARENESS OF BLADE TO TABLE " adjustment on page 30 . CHECKING BLADE FOR HEEL IMPORTANT : Saw blade MUST be parallel to miter gauge groove , To check for parallelism , refer to " HEELING ADJUSTMENT OR PARALLELISM OF SAWBLADE TO MITER GAUGE GROOVE " adjustment on page 29 and 30 . ASSEMBLING STEEL LEGS NOTE : Steel Legs are furnished with Model 113.298031 and 113,298151 . From among the loose parts , find the following Hardware : 24 Truss Head Screws , 1 / 4 - 20 X 5 / 8 in . long ( top of screw is rounded ) SIDE STIFFENER 24 Lockwashers , 1 / 4 in . External Type ( approx . dia , of hole 1 / 4 in . ) 24 Hex Nuts , 1 / 4 - 20 ( approx . dia . of hole 1 / 4 in . ) 8 Hex Nuts , 1 / 2 - 13 ( approx . dia . of hole 1 / 2 in . ) 4 Leveling feet . Assemble the legsasshown . , . END 1 . Insert the Truss Head Screws through the holes in the STIFFENER " legs , then through the holes in the stiffeners . MAKE SURE THE SCREWS GO THROUGH THE HOLES IN THE SIDE STIFFENERS MARKED " × " . 2 . Install the Iockwashers . . . screw on the nuts but do not tighten until completely assembled . 3 . Install leveling feet . IN . HEX NUTS _ LEVELING FOOT
Page: 9

MOUNTINSGAW 1 . From among the loose parts , find the following hardware : 4 Hex Head Screws . 5 / 16 - 18 x 1 - 1 / 4 in . long . 4 Hex Nuts , 5 / 16 - 18 ( approx . dia . of hole 5 / 16 in . ) 4 Lockwashers , 5 / 16 in . External Type ( approx . dia . of hole , 5 / 16 in . ) 8 Flat Washers , ( dia . of hole 11 / 32 in . ) 2 . Place saw on legsso that holes in bottom of saw line up with holes in top of legs . 3 . Install screws , washers , Iockwashers and nuts asshown . / / SAW BASE 17 ENDTIFFENER " S _ t FLAT WASHER - - - _ _ ' 13 LOCKWASHER " _ ' _ ' . Ex If you mount the saw on any other bench , make sure that there is an opening in the / top of the bench the same size as the opening in the bottom of the saw so that the sawdust can drop through . Recommended working height is 33 to 37 inches from the top of the saw table to the floor . ATTACHING AND ASSEMBLING TABLE EXTENSIONS If you received Table Extensions with your saw ( two furnished with Model No . 113.298031 ) or one furnished with Model No . 113.298151 ) attach them at this time . If you have only one Table Extension , it may be attached to either side . NOTE : When the Table Extension is attached to the left side , it offers more support to the workpiece , especially when crosscutting or mitering long boards . When attached to the right side , it offers more support when curing wide panels . If you attach the Extension to the left side , be sure to construct the Auxiliary Fence / Work Support and Push Block shown in " Basic Saw Operation " section . 1 . From among the loose parts find the following hardware . NOTE : Double number of hardware if assemblingextensions for Model 113.298031 . BLOCK OF WOOD 2 Corner Support Brackets \ 2 Corner Stiffener Brackets 8 Truss Hd . Screws 1 / 4 - 20 x 1 8 Ext . Lockwashers 1 / 4 8 Hex Nut 1 / 4 - 20 / 4 Hex Hd . Screws 5 / 16 - 18 x 1 - 1 / 4 4 Ext , Lockwasher 5 / 16 4 Hex Nut 5 / 16 - 18 Align front edge of extension with front edge of saw table . Assemble brackets with hardware as listed . Pull Extension UPWARDS above table surface . . . SLIGHTLY TIGHTEN SCREWS using 1 / 2 in . wrench . Insert 5 / 16 - 18 x 1 - 1 / 4 in . long screws through holes in EXTENSION then through table . Install flat washer , Using small block of hardwood and hammer , l : ap extension DOWNWARDS at front , center & rear , unti it is EVEN Iockwasbers , and screw on the nuts . . . DO NOT with table surface . . . TIGHTEN SCREWS . TIGHTEN .
Page: 10

LayREARFENCE GUIDE BAR on table to act as a straightedge . If outer edge of extension is higher or lower than table surface ; A . Slightly loosen nuts holding bracket to extension using 7 / 16 in . wrench . B . Move end of extension up or down until outer edge is even with table surface . . . check with GUIDE BAR . . , tighten nuts . C . Recheck INNER edge of extension to make sure it has not moved . . . readjust , if necessary . INSTALLING RIP FENCE GUIDE BARS AND SWITCH BOX 1 . From among the loose parts find the following hardware : 2 Hex . Head Screws , 5 / 16 - 18 x 1 - 3 / 4 in . long 2 Hex Head Screws , 5 / 16 - 18 x 1 in . long 1 Hex , Head Screw , 5 / 16 - 18 x 3 / 4 in . long 5 External Lockwashers , 5 / 16 in , ( approx . dia . of hole 5 / 16 in , ) 5 Hex . Nuts . 5 / 16 - 18 ( approx . die . of hole 5 / 16 in . ) / 2 Flat washers ( dia . of hole 21 / 64 in , I 2 Spacers , 3 / 4 in . dia . x 1 / 2 in . long ! 2 Self - threading nuts 1 Fence Guide Bar Rod then through the hole at EXTREME LEFT SIDE OF 2 . Lay guide bars on sawtable . SWITCH then through SEVENTH hole in bar . Hold NOTE : The various holes in the bar allow them to be them in place with a piece of masking tape . . . Insert positioned on this saw and also makes them adaptable the 3 / 4 in . long screw through a flat washer and then to other models . through hole at RIGHT SIDE OF SWITCH and then through the EIGHT hole in bar . Install a Iockwasher 3 . Insert a 1 - 3 / 4 in . long screw through the THIRD hole and nut and tighten . from the LEFT IN THE FRONT BAR . . . insert another 1 - 3 / 4 in . long screw through a flat washer and 4 . Place spacers on screws . Insert bolts through holes in middle and on right sideof front of saw table . . . install Iockwashers and nuts . DONOr SCREW NUTS ON ALL THE WAY , just get them started on the screws . 6 = Remove the 3 screwsfrom rear of table extension . 7 . Insert 1 in . long screws in SECOND and FOURTH holes of rear bar and attach to table the same way . Insert ends of FENCE GUIDE BAR ROD through round holes at outer end of bars , NOTE : The ends of the ROD are not threaded . . , the SELF THREADING NUTS will cut threads on the rod asthey are screwed on . \ 10
Page: 11

9 , Nold rod with one hand and with a 1 / 2 in . wrench or pliers start screwing on ONE of the nuts only A TURN OR TWO . . . screw on other nut the same way . 10 . Using TWO 1 / 2 in . wrenches or pliers tighten both of the nuts . 1 I . Slide the bars so that screws are in the MIDDLE of the slotted holes . 12 . Position rip fence over miter gauge groove , holding up the rear end while engaging front end with bar . . , lower fence onto table . 8 THICKNESSES 13 . Raise blade all the way up . OF PAPER 14 . Carefully move fence against blade . 15 . Move front bar until " ' 0 " " mark on rip scale is approximately at tip of pointer , 16 . Move FRONT bar upwards until fence is approximately 1 / 32 in . above table . . . tighten screw at left end of bar . NOTE : Fold a piece of newspaper making 8 thicknesses and place between rip fence and table to act as a spacer . This will hold the fence off of the table approx . 1 / 32 in . 17 . Adjust rear bar so that the fence is approximately 1 / 32 in . above table make sure it is square with fence guide bar rod . . . tighten screw at end of bar . \ 18 . Replace screws in rear of table extension . . . be sure top surface of extension is PARALLEL to top surface \ of rear guide bar . 8 THICKNESSES OF PAPER 19 . Move fence to RIGHT edge of table . . . make sure it is approx . 1 / 32 in . above table at front and rear and tighten screws . 11
Page: 12

ALIGNING RIP FENCE The fence should slide easily along the bars and always remain in alignment ( parallel to sawblade and miter gauge grooves ) . The alignment is maintained by a spring underneath the fence which bears against the front guide bar , To move the fence , loosen the lock handle and grasp the fence with one hand at the front . For very close adjustments , grasp the guide bar with both hands and move the fence with your thumbs . F Place fence on saw but DO NOT LOCK IT . Move the REAR END of the fence slightly to the right or left . . . when you release it , the fence should " spring " back to its original position . If it does not , the spring pressure must be INCREASED . 1 . Loosen the screws . 2 . Move Spring slightly toward front of fence . 12
Page: 13

If the fence does not slide easily along the bars , the pressure of the spring can be REDUCED . 1 . Loosen the screws . 2 . Move spring slightly toward rear of fence . . . tighten screws . HEX SCREWS 3 , The rip fence must be PARALLEL with the sawblade ( seepage 29 ) and miter Gauge grooves . . . Move fence FENCE HEAD until it is along side of groove . Do NOT LOCK IT . It should be parallel to groove . If it is not ; A . Loosen the two " Hex . Head Screws . " B . Hold fence head tightly against bar . . . move end of fence so that it is parallel with groove , C . Altemately tighten the screws . ADJUSTING RIP SCALE POINTER 1 . Turn ELEVATION HANDWHEEL clockwise until blade is up as high as it _ will go . LOCK HAi ' _ DLE IMPORTANT : BLADE must be SQUARE ( 90 ° ) to TABLE , in order to ALIGN rip fence . 2 . Position fence on right side of sawblade so that it touches the sides of the teeth . . . tighten lock handle . 3 . Loosen screw holding the pointer . . . adjust pointer so that it points to " 0 " . . . tighten screw . NOTE : If you cannot adjust pointer so that it points to " 0 " , loosen the _ crews holding the front guide bar and move the guide bar . 13
Page: 14

INSTALLING BLADE GUARD 1 . From among the loose parts , find 2 Hex Head Screws , 1 / 4 - 20 x 5 / 8 in . long 2 Hex Head Screws , 5 / 16 - 18 x 5 / 8 in . long 2 Hex Head Screws , 5 / 16 - 18 x 1 in . long GUARD SUPPORT 2 Hex Nuts , 1 / 4 - 20 5 / 16 - 18 X ( approx . dia . of hole 1 / 4 in . ) 5 / 8 iN . 2 Lockwashers , 1 / 4 in , External Type HEXCREW ( approx . dia . of hole 1 / 4 in . ) S 2 Lockwashers , 5 / 16 in . External Type ( approx , dia . of hole 5 / 16 in . } 1 Thumbscrew Guard Support CRADLE 5 / 16 - 18 X t IN . Spreader Support HEX HD . SCREW Spreader Rod 2 . Lower the blade . 5f16 - 1Bk 5 / 8 . 3 . Screw the two MOTOR BASE CLAMP SCREWS part HEX HD . SCREWS way into cradle . 4 . Attach GUARD SUPPORT . . , DO NOT TIGHTEN screws . THUMB SCREW • SPREADER Insert SPREADER ROD into SPREADER SUPPORT ROD until pin fits into notch , Insert Thumbscrew and tighten \ it FLAT SURFACE SPREADER SUPPORT ( INTO SUPPORT ) II u 1 / 4 - 20 HEX HD . SCREW 1 / 41N . LOCKWASHEI 1 / 4 - 20 flEX NUT 6 . Slide SPREADER ROD into GUARD SUPPORT until left end of ROD extends approximately 1 / , inch beyond edge of SUPPORT . . . Snug up Hex Head Screw in SUPPORT . 7 . Attach SPREADER to SPREADER SUPPORT so that screws are all the way back in the SLOTS of SUPPORT _ _ _ tighten screws . 8 . Raise ANTIKICKBACK PAWL ( hold it in place with a piece of masking tape ) • . . align spreader SQUARE to table END OF ROD NOTE : The framing { or combination ) square must be I / 4 INCH TO LEF " true " - - see start of " assembly and alignment " section OF EDGE OF on page 6 for checking method , SUPPORT . . . Tighten both 5 / 16 - 18 x 1 in . HEX HEAD SCREWS . GUARD SUPPOR ' j - 18 x I IN . HEX HD . SCREWS SCREWS ALL THE I t BACK IN SLOTS [ IN SUPPORT 14
Page: 15

9 . Raise blade all the way up . . . make sure it is _ quare with table . 10 . Raise Blade Guard . . . lift up both ANTIKICKBACK PAWLS . . . insert one of the SETSCREW WRENCHES in the notches to hold the pawls out of the way , 11 . Lay blade of square or other straightedge alongside of blade . 12 . Loosen Hex Head Screw in GUARD SUPPORT and move spreader so that it touches blade of square . . . tighten screw . 13 . NOTE : The spreader s now square with the table and approximately in line with the sawblade . The spreader requires further adjustment to align it PARALLEL to the blade and in the MIDDLE of the cut ( KERF ) made by the sawblade . SPACE EQUAL TO APPROX . 3 THICKNESSES OF PAPER KERF WOOD 14 . IMPORTANT : The SPREADER must always be BLADE PARALLEL to the sawblade and in the MIDDLE of the I cut ( KERF ) made by the sawblade , \ / NOTE : The spreader is thinner than the width of the KER F by approximately six thicknesses of paper . SPACE EQUAL TO APPROX . LOOKING DOWN ON SAW 3 THICKNESSES OF PAPER 15 . Make two folds in a small piece ( 6 x 6 in . ) of ordinary NEWSPAPER maki ng three thicknesses . The folded paper will be used as a " spacing gauge " . 15
Page: 16

FOLDED PAPER 16 . PlacReIPFENCE on table . . . CAREFULLY move it against blade so that it is parallel to the blade , and just TOUCHES tips of saw teeth . . . tighten RIP FENCE LOCK KNOB HANDLE . 17 . Insert folded paper between SPREADER and FENCE . . . hold spreader flat against fence . . , tighten screws using 7 / 16 in . wrench , Now tighten Hex Hd . Screws in Support . 7 / ' 16 IN . WRENCH 18 . To remove BLADE GUARD AND SPREADER , loosen THUMBSCREW . , . DO NOT LOOSEN OTHER SC R EWS . MOUNTING THE MOTOR NOTE : Motor is included with Model 113.298031 and KEY 113.2981 51 . / CHECK MOTOR ROTATION 1 . The motor must rotate CLOCKWISE when viewed from the 5 / 8 in . shaft . 2 . MAKE ' SURE " KEY " IS REMOVED FROM SHAFT . 3 . Place the motor on your we rkbench or on the floor . 4 , Plug the cord into a properly grounded outlet ( See 5 / 8 IN . " Motor Specifications and Electrical Requirements " DIA . SHAFT Section ) Notice the rotation of the shaft , If t is not turning CLOCKWISE , REMOVE the plug from the WARNING : FOR YOUR OWN SAFETY , MAKE SURE outlet , and change the rotation of the motor according PLUG IS NOT CONNECTED TO POWER SOURCE to the instructions furnished with the motor , OUTLET WHEN CHANGING MOTOR ROTATION . 5 . From among the loose parts , find the following hardware : LOCKWASHER THESE I " VVO CARRIAGE BOLT 4 Carriage Bolts , 5 / 16 - 18 x 3 / 4 in . long 5 / 16 IN . EDGES EVEN 5 / 16 - 18 X 3 / 4 [ _ J . 4 Hex , Nuts , 5 / 16 - 18 ( approx . dia . of hole 5 / 16 in . ) 5 / 16 - 18 4 Lockwashers , 5 / 16 in . External Type NUT ! ( approx . dia . of hole 5 / 16 in , ) SHAF - _ 4 . ( _ ti / " GUARD 6 . Remove Blade Guard and Spreader . \ / 7 . Place motor on MOTOR BASE . . . insert bolts through ( holes in base . . . then through the motor . Install / . Iockwashers , and nuts . MOTOR BASE B . Position motor so that edge of MOTOR FOOT and MOTOR BASE are even . . . slide motor all the way to MOTOR MOUNTING the RIGHT . . . tighten the four nuts . BASE 9 , Loosen set screw in motor pulley using 6 / 32 in . setscrew wrench . Slide pulley on shaft with HUB away PULLEY from motor . DO NOT TIGHTEN SETSCREW , KEY 10 . Install 3 / 16 in . square key ( furnished with motor ) in grooves in pulley and motor shaft , DO NOT TIGHTEN SETSCREW . 16
Page: 17

11 . Lift motor and insert the TWO PINS on motor base into HOLES in cradle . . . push motor in asfar as it will go . 12 . Lower the blade . . . install belt on saw pulley and motor pulley . 13 . Sight along edges _ of both pulleys arid move motor pulley so that belt is parallel to the edges of both EDGE OF WASHER pulleys . . . tighten the setscrew in the motor pulley . EVEN WITH END 14 . IMPORTANT : Measure the distance from end of motor OF SLOT shaft to pulley . . . mark this dimension down ; you will need it later when reinstalling the pulley . 15 . Make sure blade is 90 ° to table . . . raise i _ all the way MOTOR BASE up . CLAMP SCREWS _ 16 . Lift motor until edge of washer is even with end of slot . . . tighten pivot screw . In this ! _ osition , pull motor toward you ( pins will slide out of cradle ) until belt is TIGHT . . . tighten the two MOTOR BASE CLAMP SCREWS . 17 . Loosen Pivot Screw slightly . 18 . Lower the saw blade all the way down . 19 . IMPORTANT ; Motor should pivot freely downward as blade is lowered . If it does not , LOOSEN the PIVOT SCREW some more . MOTOR PULLEY 20 . Pivot screw must be adjusted only tight enough to allow motor to pivot FREELY as blade is raised or lowered , This will maintain constant tension on belt . CAPACITOF COVER 21 . Loosen the two MOTOR CLAMP SCREWS on each end \ of motor . Rotate the motor so that the CAPACITOR COVER is on top . . . tighten the screws . The ventilation holes are now facing downward which will help prevent sawdust from entering motor , VENTILATION \ MOTOR HOLES CLAMPSCREW ( BOTH ENDS ) 17 /
Page: 18

TOGETHER _ _ - _ TWO HOLES CLOSEST INSTALLING BELT GUARD BELT GUARD 10 - 32 X 1 / 2 IN . SUPPORT BRACKET SE L . F - THREADING 1 . Remove the belt and motor pulley . SCREW \ 2 . Screws furnished witli guard are " self threading " . . . \ screw them into holes in BELT GUARD SUPPORT BELT GUARD SUPPORT BRACKET , then remove them . 3 . Position BELT GUARD SUPPORT BRACKET and BELT GUARD SUPPORT as shown and install the BELT GUARD screws . . . make sure motor shaft is in CENTER of hole in SUPPORT . \ PIVOT SCREW / / CENTERED OPENING 4 . Install three CLIPS ( furnished with guardi 90 ° apart starting with one clip at the end of the guard as shown • . . LONG END of cl p facingAWAY from you . BELT GUARD j _ _ , _ CLIPS N LONG END BELT . 5 . Reinstall , motor pulley the same way it was when you aligned the belt , 6 . Place belt on SAW'PULLEY , . . insert end of belt through opening in END of guard , 7 . Slip belt over motor pulley . 18
Page: 19

Press guard onto support so that bottom of guard is approximately 3 / 4 in . away from belt . NOTE : To remove guard , lift up on LONG TABS of cl ps . . . pull guard outward . The clips should remain on the BELT GUARD SUPPORT . 1 3 / _ IN . PLUGGING IN MOTOR 1 . From among the loose parts , find two wire ties 2 . Route motor cord along right side of cabinet and snap ties in 1 / 4 " hole in side of cabinet . Secure two cords in w _ re ties . 3 . Plug motor cord into outlet on side of switch box . NIRE TIES 19
Page: 20

GETTING TO KNOW YOUR SAW _ 1 SAWSLADE 7 " BLADE GUARD TABLEINSERT MITER GAUGE | 0 EXACT - I - CUT ANTIKICKBACK \ PAWLS LOCK HANDLE 6 MITER GAUGE RiP FENCE RIP FENCE LOCK HANDLE 4 TILT LOCK HANDLE ( UNDERNEATH TABLE ) 2 ELEVATION HANDWHEEL \ 1 ON - OFF SWITCH 1 ON - OFF SWITCH CAUTION : Before turning switch on , make sure the blade guard is correctly installed and operating properly . The On - Off Switch has a locking feature . THIS FEATURE IS INTENDED TO PREVENT UNAUTHORIZED AND @ POSSIBLE HAZARDOUS USE BY CHILDREN AND OTHERS _ KEY B . TO turn saw ON . . . stand to either side of the ( YELLOWPLASTIC ) blade never in line with it . . . insert finger under switch lever and pull END of lever out . After turning switc _ h ON , always allow the blade to come up to full speed before cutting . Do not cycle the motor switch on and off rapidly , as this may cause the sawblade to loosen . ! n the event this should ever occur , allow the sawblade to come to a complete stop and retighten the arbor nut normally , not excessively , Never leave the saw while the power is " ' ON " . C . TO turn saw OFF . . . PUSH lever in . Never leave the saw until the cutting tool has come to a complete stop . D . TO lock switch in OFF position . . . hold switch IN with one hand . . . REMOVE key wi _ other hand . WARNING : FOR YOUR OWN SAFETY , LOWER BLADE OR OTHER CUTTING TOOL BELOW TABLE SURFACE . ( IF BLADE IS TILTED , RETURN IT TO VERTICAL ( 90 ° ) POSITION ) . ALWAYS LOCK THE SWITCH " OFF " , WHEN SAW IS NOT IN USE . . . REMOVE KEY AND KEEP IT IN ASAFE PLACE . . . ALSO , . . IN THE EVENT OF A POWER FAILURE ( ALL OF YOUR LIGHTS GO OUT ) TURN SWITCH OFF . . . LOCK IT AND REMOVE THE KEY . THIS WILL PREVENT THE SAW FROM STARTING UP AGAIN WHEN THE POWER COMES BACK ON , 2O
Page: 21

2 ELEVATIOHNANDWHEEL . e . . levateosrlowertshe Select a suitable piece of smooth straight wood . . , drill bladeT . urnclockwisteo elevat . e . . counterclockwise two holes through it and attach it with screws . tolower , NOTE ; When bevel crosscutting , attach facing so that it extends to the right of the miter gauge and use the 3 TILT HANDWHEE . L . . tilts the bladefor bevel miter gauge in the groove to the right of the blade . ' cutting . Turn clockwiseto tilt towardleft . . . counterclockwise to tilt toward right , When the blade is tilted to the LEFT asfar asit will go , it should be at 45 ° to the table and the bevel pointer should point 45 ° . NOTE : There are LIMIT STOPS inside the saw which prevent the blade from tilting beyond 45 ° to the LEFT and 90 ° to the RIGHT . ( See " Adjustments " section " Blade Tilt , or Squareness of Blade to Table " ) , 4 TILT LOCK HANDLE . . . locks the blade in the AUXIELIARY FACING STOP PIN 45 ° SLOT " \ desired tilt position . To loosen , turn counterclockwise , FOR STOP PIN Push handle in and turn it to another position if \ necessaryin order to tighten or loosen . 5 RIP FENCE . . is locked in place by tightening the BLADEGUARD must always be in place and working lock knob . To move the fence , loosen the knob and properly for all thru - sawing cuts . That is , all cuts grasp the fence with one hand at the front . whereby the blade cuts completely through the Holes are provided in the rip fence for attaching a wood workpiece . facing when using the dado head , or molding head . To remove the guard for special operations , loosen the Select a piece of smooth straight wood approx . 3 / 4 in . thumbscrew and slide the guard off of the rod . DO NOT DISTURB THE SETTING OF THE ROD . thick and the same size as the rip fence . Attach it to the fence with three Round Head # # 10 When replacing the guard , make sure the PIN in the rod Wood Screws 2 in . long . To remove the facing , loosen engageswith the NOTCH in the spreader support , Make the screws , slide the facing forward and pull the screws sure thumbscrew is tightened securely , through the round holes . 8 TABLE INSERT is removable for removing or installing WOOD FACING blades or other cutting tools . \ \ \ ROUND HEAD / / / # ! 0 WOOD SCREWS / SCREW 6 MITER GAUGE . . . head is locked in position for crosscutting or mitering by tightening the lock knob . ALWAYS LOCK IT SECURELY WHEN NUSE . There are two slots for the stop pin at the 45 degree WARNING : FOR YOUR OWN SAFETY , TURN right and left positions for conveniently setting the SWITCH " OFF " AND REMOVE PL . UG FROM Vliter Gauge to cut miters . POWER SOURCE OUTLET BEFORE REMOVING INSERT . NOTE : The slots for the stop pin and the graduations are manufactured to very close tolerances which A , Lower the blade below the table surface . provide accuracy for average woodworking . In some B . Raise blade guard . caseswhere extreme accuracy is required , when making C . Loosen Screw . angle cuts , for example , make a trial cut and then recheck it . D . Lift in _ ert from front end , and pull toward front of saw . If necessary , the miter gauge head can then be swiveled slightly to compensate and then locked . NEVER OPERATE THE SAW WITHOUT THE PROPER INSERT IN PLACE . USE THE SAW BLADE Slots are provided in the miter gauge for attaching an INSERT WHEN SAWING . . . USE THE AUXILIARY FACING to make it easier to cut long p = eces . Be positive facing does not interfere with the COMBINATION DADO MOLDING INSERT WHEN proper operation of the sawblade guard . DADOING OR MOLDING . 21
Page: 22

9 REMOVING AND INSTALLING SAWBLADE . WARNING : FOR YOUR OWN SAFETY , TURN SWITCH " OFF " AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE REMOVING OR INSTAL LING SAWBLADE . A . Raise Blade Guard . . . remove insert . B . To REMOVE blade , place a block of wood / against front of blade . . . PULL arbor wrench / OR NUT WOOD BLOCK toward you to LOOSEN arbor nut . BLADE GUARD NOT SHOWN FOR PICTURE CLARITY BLADE GUARD NOT SHOWN FOR PICTURE CLARITY C . To TIGHTEN arbor nut , place a block of wood against rear of blade ; . . PUSH wrench away from you . When installing the blade . . . make sure the teeth are pointing toward the front of the saw . . . and that the blade and collars are clean , and free from any burrs . The HOLLOW side of the collar must be against the blade . Always tighten the arbor nut securely . NOTE : When using the Dado or Molding Head , itis not necessary to install the loose collar . NUT To replace insert . LOOSE Place insert into insert opening n table and push COLLAR keyslot in insert will drop over screw . Tighten screw . _ , toward rear of saw to engage spring clip and unt , I AR , OR ff _ , _ Do not tighten screw to the point where it will deflect ( _ " / / _ \ ARBORNUT the insert , r _ _ _ _ _ _ TEEFTOH , NTT , O . O ' • FRONT OF SAW h _ , v 1 0 EXACT - I - CUT The ' yellow " plastic disc imbedded n the table in front of the sawb ! ade , is provided for marking the location of the sawcut on the workpiece . A . Check disc . . . if it is above table surface , place a piece of hardwood on top of it and tap it down . B . With blade 90 ° ( square to table ) cut off a piece of wood . C . Pull miter gauge back until wood is over disc . Using very sharp pencil , mark a line on disc . D With miter gauge in right hand groove , follow same procedure and mark another line on disc BLADE GUARD NOT SHOWN FOR PICTURE CLARITY E . These I in es " mdlc " ate the " " path " " of the cut ( kerf ) made by the sawblade . F . When cutting the workpiece , ine up mark on workpiece with line on disc . 22
Page: 23

BASIC SAW OPERATION WORK HELPERS AUXILIARY FENCE / WORK SUPPORT Make one using a piece of 3 / 8 in and 3 / 4 in . plywood . Before cutting any wood on your saw , study all of the Fasten together with glue and woodscrews . " Basic Saw Operations " . NOTE : Since the Push Block is used with the Auxiliary Notice that in order to make some of the cuts , it is Fence , the 4 - 3 / 4 in . dimensions must be held identical on necessary to use certain devices " ' Work Helpers " like the both the pieces . Push Stick , the Push Block and the Auxiliary Fence / Work THESE EDGES MUST Support , which you can make yourself . BE PARALLEL 3 / 4 PLYWOOD After you have made a few practice cuts , make up these / " helpers " before starting any projects . Make the " Push Stick " first . _ / 1 _ 4 - 3 / 4 - 4 \ _ ' - 4 PUSH STICK AND PUSH BLOCK Make the Push Stick using a piece of 1 x 2 , or rip one from a wide board , say 11 - 1 / 2 in . wide , and set the rip fence 9 - 7 / 8 in . from the sawblade . Make the Push Block using a piece of 3 / 8 in . and 3 / 4 in . 2 - I / 2 7 " - plywood . The small piece of wood 3 / 8 in . x 3 / 8 in . x 2 - 1 / 2 in . should _ 5 - / 8 _ be GLUED to the plywood . . . DO NOT USE NAILS . This 3 / 8 I is to prevent dulling the sawblade in the event you PUSH BLOCK I mistakingly cut into the push block . NOTE : All dimensions in inches 3 / 8 PLYWOOD Position the handle in the center of the plywood and fasten together with glue and woodscrews . 3 / 4 PLYWOOD 27 1 - 1 / 4 45 ° NOTCH 1 - 5 / 8 = IECE END THIS FACE AND THIS _ ' _ 30 1 / _ 1 / 4 EDGE MUST BE PARALLEL PUSH STICK AUXILIARY PENCE / 3 / 8 PLYWOOD NOTE : All dimensions in inches WORK SUPPORT - . _ \ Jj . 5 - 1 / 2 NOTE : All dimensions in inches _ ' _ . USING THE MITER GAUGE CROSSCUTTING , MITER CUTTING . BEVEL CUTTING . 6 . Do not stand directly in front of the blade n case of a COMPOUND MITER CUTTING , DADOING and when THROWBACK ( Small cut - off piece caught by the back RABBETTING AND MOLDING across the end of a narrow of the blade and thrown toward the operator ) . Stand to workpiece , THE MITER GAUGE IS USED , either side of the blade . 7 . Keep your hands clear of the blade and out of the path WARNING : FOR YOUR OWN SAFETY , ALWAYS of the blade . OBSERVE THE FOLLOWING SAFETY PRECAUTIONS IN ADDITION TO THE SAFETY INSTRUCTIONS ON 8 . If blade stalls or stops while cutting , TURN SWITCH PAGES 2 , 3 , and 4 , OFF before attempting to free the blade . 1 . Never make these cuts freehand ( without using the g . Do not reach over or behind the blade to pull the miter gauge or other auxiliary devices ) because the workpiece through the cut . . . to support long or blade could bind in the cut and cause a KICKBACK or heavy workpieces . . . to remove cut - off pieces of cause your tinge rs or hand to slip into the blade . material or FOR ANY OTHER REASON . 2 , Always lock the miter gauge securelv when in use . 10 . Do not pick up small pieces of cut - off material from the 3 . Remove rip fence from table . table . REMOVE them by pushing mere OFF the table with along stick _ Otherwise they could he thrown back 4 . Make sure blade guard is installed for all " ' thru - sawmg ' " at you by the rear of the blade , operations ( when sawblade cuts entirely thru the 11 . Do not remove sinai pieces of cut - off material that may thickness of the workpieee . ) Replace guard become TRAPPED inside the blade guard while the saw IMMEDIATELY after completion of dadoing , molding is RUNNING . THIS COULD ENDANGER YOUR or rabbeting cuts . HANDS or cause a KICKBACK . 5 . Have blade extend approximately 1 / 8 in . above top of Turn the saw OFF . After the blade has stopped turnin g , workpiece . Additional blade exposure would increase lift the guard and remove the piece . the hazard potential . 23
Page: 24

CROSSCUTTING CROSSCUTTING is known as cutting wood across the grain , at 90 ° , or square with both the edge and the flat side of the wood , This is done with miter gaugeset at " ' O " . The graduations on the miter gauge provide accuracy for average woodworking . In some cases where extreme accuracy is required , when making angle cuts , for example , make a trial cut and then recheck it with an accurate square , or protractor . If necessary , the miter gauge head can be swiveled slightly to compensate for any inacurracy , NOTE : The space between the miter gauge bar and the groove in the table is held to a minimum during manufacturing . For maximum accuracy when using the miter gauge , always " favor " one side of the groove in the table , In other words , don't move the miter gauge from side to sidewhile cutting , The miter gauge may be used in either of the grooves in the table . Make sure it is locked . but keep one side of the bar riding against one side of the groove . When using the miter gauge in the LEFT hand groove , hold NOTE : Glue a piece of sandpaper to the face of the miter the workpiece firmly against the miter gauge head with gauge head , This will help prevent the workpiece from your left hand , and grip the lock handle with your right . " creeping " while it is being cut . When using the RIGHT Hand groove , hold the workpiece The Hold - Down Clamp ( Optional Accessory ) should be with your right hand and the Iockhandle with your left hand . used on the miter gauge for greater accuracy . When cutting long workpieces , invert AUXILIARY FENCE / WORK SUPPORT and position it on top of the guide bars to support the workpiece as near to the end as AUXILIARY P [ NCEI possible . If this does not adequately support the workpiece , WORK SUPPORT you can make a simple support by clamping a piece of plywood to a sawhorse . Use the Hold - Down Clamp ( Optional Accessory ) on the miter gauge for greater accuracy . STOP RODS REPETITIVE CUTTING REPETITIVE CUTTING is known as cutting a quantity of pieces the same length without having to mark each piece , 1 . Use the Stop Rods ( optional accessory ) only forcutting duplicate pieces6 in . long and longer . 2 . DO NOT FEED workpiece with RIGHT Hand , hmerelye guide it , making sure that it does not bind or pinch t sawblade . When making repetitive cuts from a long workpiece , make sure it is adequately supported . Use the Hold - Down Clamp ( Optional Accessory ) on the miter gauge for greater accuracy . ! NCE / WORK SUPPORT 24
Page: 25

\ / / 1 . NEVER USE THE RIP FENCE AS A LENGTH STOP \ BECAUSE THE CUTOFF PIECE COULD BIND BETWEEN THE FENCE AND THE BLADE CAUSING BLOCK A KICKBACK , 2 . When making repetitive cuts shorter than 6 in . , clamp a block of wood 2 in . long to the table to act as a length stop . Do not clamp directly to the bottom edge of the table because the " swivel " of the clamp will not grip properly . Place a small block of wood between the bottom edge of the table and the " C " clamp . CAUTION : When clamping the block , make sure thate the end of the block is well in front of the sawblade . B sure it is clamped securely . 3 . Slide the workpiece along the miter gauge until it touches the block . . . hold it securely or clamp it with the Hold - Down Clamp ( Optional Accessory ) . 4 . Make the cut . . . pull the workpiece back . . . push the cut off piece off the table with a long push stick . . . CUT OFF DO NOT ATTEMPT TO PICK IT UP AS THIS COULD PIECE ENDANGER YOUR HANDS . ! t _ , % \ MITER CUTTING MITER CUTTING is known as cutting wood at an angle other than 90 ° with the edge of the wood . Follow the same procedure asyou would for crosscutting . Adjust the miter gaugeto the desired angle , and lock it . The miter gauge may be used in either of the grooves in the table . When using the miter gauge in the LEFT Hand groove , I _ old the workpiece firmly against the miter gauge head with your left hand , and grip the lock knob with your right . When using the RIGHT hand groove , hold the workpiece with your right hand and the knob with your left hand . Use the Hold - Down Clamp ( Optional Accessory ) on the miter gauge for greater accuracy . BEVEL CROSSCUTTING BEVEL CROSSCUTTING is the same as crosscutting \ except that the wood is also cut at an angle . . . other than \ 90 ° with the flat side of the wood . \ Adjust the blade to the desired angle . Use the Miter Gauge in the groove to the RIGHT of the \ blade . It cannot be used in the groove to the LEFT because \ the blade guard wilt interfere . Hold the workpiece with your right hand and the Iockhandle with _ / our left hand . Use the AUXILIARY FENCE / WORK SUPPORT for additional support of the workpiece . Lay it acrossthe guide bars to support the workpiece as near to the end as possible . Use the Hold - Down Clamp ( Optional Accessory ) on the miter gauge for greater accuracy . COMPOUND MITER CUTTING COMPOUND MITER CUTTING is a combination of miter cutting and bevel crosscutting . The cut is made at an angle other than 90 ° to both the edge and the flat side of the wood . Adjust the miter gauge and the blade to the desired angle . . . Make sure miter gauge is locked , 25
Page: 26

USING THE RIP FENCE RIPPING , BEVEL RIPPING , PLOUGHING , MOLDING , not DIG into the workpiece and HOLD it . . . the pawls RESAWING AND RABBETING are performed using the must be SHARPENED . See " Maintenance " section . RIP FENCE together with the AUXILIARY 5 . Have blade extend approximately 1 / 8 n . above top of FENCE / WORK SUPPORT , PUSH STICK OR PUSH workpiece . Additional blade exposure would increase BLOCK . the hazard potential . WARNING : FOR YOUR OWN SAFETY , ALWAYS 6 . Do not stand directly in front of the blade in case of a OBSERVE THE FOLLOWING SAFETY PRECAUTIONS KICKBACK . Stand to either side of the blade . IN ADDITION TO THE SAFETY INSTRUCTIONS ON 7 . Keep your hands clear , of the blade and out of the path of the blade . PAGES 2 , 3 . and 4 . 8 . If the blade stalls or stops while , cutting . TURN SWITCH OFF before attempting to free the blade . Never make these cuts FREEHAND ( without using the 9 . Do not reach over or behind the blade to pull the rip fence or auxiliary devices when required ) because workpiece through the cut . . . to support long or the blade could bind in the cut and cause a heavy workpieces . . . . to remove small cut - off pieces of KICKBACK . material or FOR ANY OTHER REASON . 2 , Always lock the rip fence securely when in use . 10 . Do not pick up small pieces of cut - off material from the 3 . Remove miter gauge from table . table , REMOVE them by pushing them OFF the table 4 . Make sure blade guard is installed for all thru - sawing with a long stick , Otherwise they could be thrown back type cuts . Replace the guard IMMEDIATELY following at you by the rear or the blade . completion of resawing , rabbeting , dadoing , or molding 11 . Do not remove small pieces of cut - off materia that may operations . become TRAPPED ns de the blade guard while the saw Freouently check the action of the ANTIKICKBACK is RUNNING . THIS COULD ENDANGER YOUR PAWLS by passing the workpiece alongside of the HANDS or cause a KICKBACK . spreader while saw is OFF . Turn the saw OFF . After the blade has stopped turning , Pull the workpiece TOWARD you , If the PAWLS do lift the guard and remove the piece . RIPPING ALWAYS SUPPORT LONG WORKPIECES RIPPING is known as cutting a piece of wood with the grain , or lengthwise . This isdone using the rip fence . Position [ he fence To the desired WIDTH OF RIP and lock in place , Before starting to rip , be sure A . Rip Fence is parallel to sawblade . B . Spreader is properly aliqned with sawblade . C . Antiklcl < bac < pawls are functioning properly . When ripping LONG BOARDS or LARGE PANELS , always use a work support . A simple one can be made by clamping a piece of plywood to a sawhorse , BEVEL RIPPING When bevel ripping material 6 in . or narrower , use fence on the right side of the blade ONLY . This wil provide more space between the fence and the sawblade for use of a push stick . If the fence is mounted to the left . the sawblade guard may interfere with prc per use of a push stick . / / ' When " WIDTH OF RIP " is 6 in , and WIDER use your RIGHT Hand to feed the workpiece until it is clear of the table . Use LEFT hand ONLY to guide the workpiece , . . do not FEED the workpiece with the left hand . 3 / ° i ! ) 26 / ,
Page: 27

When " WIDTH OF RIP " is 2 in . to 6 in , wide USE THE PUSH STICK to feed the work . When WIDTH OF RIP is NARROWER than 2 in . , the push stick CANNOT be used because the guard will interfere . _ . USE the AUXILIARY FENCE _ WORK SUPPORT and PUSH BLOCK . Attach Auxiliary Fence / Work Support to rip fence with two " ' C ' " clamps . Feed the workpiece by qand along the AUXILIARY FENCE unti the end is approx . 1 in . past the front edge of the table . Continue to feed using the PUSH BLOCK . Hold the workplece in position and install the PUSH BLOCK by sliding it on top of the AUXILIARY FENCE ; WORK SUPPORT ( This May Raise Guard ) . 3AFFLE Narrow stri # s thicker than the Auxiliary Fence / Work Support may enter the guard and strike the baffle . CAREFULLY raise guard only enough to clear the workpiece . Use PUSH BLOCK to complete cut . PLOUGHING AND MOLDING MOLDING is shaping the workpiece with the grain tne long PLOUGHING is grooving with the grain the long way of the way of the workpiece , using the fence . Use proper workDiece , using the fence . USE proper holddowns and holddowns and feed devices . feed devices . 2 ? '
Page: 28

RESAWING RESAWING is known as ripping a piece of wood through its thickness . Do not attempt to resaw BOWED or WARPED material . NOTE : To RESAW a piece of wider than 3 - 3 / 8 in . . . . it will be necessa blade guard . . . and use the AUXILIARY FENCE / WORK SUPPORT . ( See " Work Helpers " ) . Clamp it to the table so that the workpiece wil SLIDE EASILY but not TILT or MOVE SIDEWAYS without SMALL BLOCK BINDING between the two fences . OF WOOD Do not clamp directly to the bottom edge of the table because the " swivel " of the clamp will not grip properly . Place a small block of wood between the bottom edge of RESAWlNG BECAUSE THIS COULD CAUSE A the table and the " C " clamp . KICKBACK . WARNING : FOR YOUR OWN SAFETY . . . 2 - INSTALL BLADE GUARD IMMEDIATELY UPON 1 . DO NOT " ' BACK UP " ( REVERSE FEEDING ) WHILE COMPLETION OF THE RESAWlNG OPERATION . CUTTING PANELS When cutting panels ( whenever fence is positioned outside of table surface ) , ALWAYS use the AUXILIARY FENCE / WORK SUPPORT . 1 . Unlock fence and raise rear end . 2 . Position AUXILIARY FENCE / WORK SUPPORT as shown and attach it with two " ' C ' " clamps . RABBETING Rabbeting is known as cutting out a section of the corner of a piece of material , across an end oralong an edge . To make a RABBET requires cuts which do not go all the way through the material . Therefore the blade guard must be removed . 1 . Remove blade guard . 2 . For rabbeting along an edge ( long way of workpiece ) as shown , add facing to rip fence ( see 5 . RIP FENCE , p . narrower make the rabbet cut with the board flat on 21 ) approximately as high as the workpiece is wide . operations , including feather boards and push stick , etc . Adjust rip fence and blade to required dimensions : then the table using the miter gage fitted w _ th a facing ( per make first cut with board flat on table as any rip ( type ) " 6 . MITER GAUGE " on p . 21 ) . DO NOT use the rip cut : make second cut with workpiece on edge . Follow fence . all precautions , safety instructions , and operational 4 . INSTALL BLADE GUARD IMMEDIATELY UPON instructions as for ripping , or rip type operations , COMPLETION OF RABBETING OPERATION . including feather boards and push stick , etc . Rabbet cuts can also be made using the dado head or 3 . For rabbeting across an end , for workpieee 101 / = " and molding head . DADOING SAW TABLE Instructions for operating the Dado Head are contained in booklet furnished with the Dado Head . \ The Recommended Dado Head is listed under Recommended Accessories in this manual . The arbor on the saw , is only long enough so that the widest cut that can be made is 13 / 16 " wide . It is not necessary to install the outside loose col ar before _ R NUT screwing on the arbor nut . Make sure the arbor nut is tight . ALWAYS USE DADO INSERT LISTED UNDER RECOMMENDED ACCESSORIES . When using . the dado head it will be necessary to remove the Blade Guard and Spreader . USE CAUTION . USE FEATHERBOARDS AND PUSH STICKS AS REQUIRED . ALWAYS REPLACE THE BLADE , GUARD AND SPREADER WHEN YOU ARE FINISHED DADOING . MOLDING CUTTING When using the molding heat it will be necessary to remove Instructions for operating the Molding Head are contained the Blade Guard and Spreader . USE CAUTION . USE in a booklet furnished with the Molding Head . FEATHERBOARDS AND PUSH STICKS , etc AS The recommended molding head is listed under REQUIRED . Recommended Accessories m this manual . ALWAYS REPLACE THE BLADE GUARD AND Always use Molding Insert Listed Under Recommended SPREADER WHEN YOU ARE FINISHED MOLDING . Accessories . 2a
Page: 29

ADJUSTMENTS LOCK KNOB WARNING : FOR YOUR OWN SAFETY , TURN SWITCH " OFF " AND REMOVE PLUG FROM POWER SOURCE STOP BAR OUTLET BEFORE MAKING ANY ADJUSTMENTS . PIN MITER GAUGE NOTE : The slots for the stop pin and the graduations are manufactured to very close tolerances which provide accuracy for average woodworking . In some cases where extreme accuracy is required , when making angle cuts , for example , make a trial cut and then recheck it . SQUARE _ INDICATOR If necessary , the miter gauge head can be swiveled slightly to compensate for any inaccuracy . 1 . Loosen the " knob " and pull " stop pin " OUT . _ 18LOCK 2 . Swivel the head . . . position it at " 0 " . . . push the stop pin IN . . . lock the handle . I 3 . The HEAD should be square with the Bar and the pointer should point to " 0 " . Readjust the pointer if necessary . 4 . If the head is not square with the bar , adjustments are required . A . Loosen the " knob " ( 1 ) and the " two screws " ( 2 ) B . Position the HEAD square with the BAR using a combination square . C . PUSH the STOP PIN into the slot in the head at " 0 " . . . push the pin into the slot and twist it . Lock the knob . D . Recheck with the square . If the head is still not square , loosen the screws ( 2 ) and readjust the INDICATOR BLOCK . 1 / 8 IN . SETSCREW E . With the head square with the bar and the pin WRENCH 2 " = = _ pushed into the slot adjust the pointer ( 3 ) to point tO " 0 " . adjusted by tightening or loosening the setscrew ( 4 ) • . . usingthe 1 / 8 in . setscrew wrench . F . The miter gauge head must rest on top of the bar NOTE : The setscrew is located inside of the head . without being able to move up and down . . . yet it must swivel freely . To reach it , swivel the head to 60 degrees anaiturn the miter gauge upside down . G . The swiveling movement of the head can be HEELING ADJUSTMENT or PARALLELISM OF SAWBLADE TO MITER GAUGE GROOVE While cutting , the material must move in a straight hlinee PARALLEL to the SAWBLADE . . . therefore both t miter gauge GROOVE and the RIP FENCE must be PARALLEL to the SAWBLADE . If the sawblade IS NOT parallel to the miter gauge groove , HARK I'XI ' ON TOOTH the blade will bind at one end of the cut . ( This is known as " HEELING " ) . To check for parallelism : WARNING - FOR YOUR OWN SAFETY , TURN SWITCH " OFF " AND REMOVE PLUG FROM POWER SOURCE OUTLET . 1 . Raise blade all the way up . . . raise blade guard . 2 . Mark as " x ' " on one of the teeth which is SET ( bent ) to the LEFT . 3 . Place the head of a combination square in the GROOVE . . . ad ) ust blade of square so that it just touches the tip of of the MARKED tooth . 4 . Move square to REAR , rotate blade to see if MARKED tooth again touches blade of square . 5 . If tooth touches square at FRONT and REAR . . . sawblade is PARALLEL to MITER GAUGE GROOVE . 29
Page: 30

6 . If tooth does not touch the same amount . . . the mechanism underneath must be adjusted to make the blade PARALLEL to GROOVE . REAR TRUNNION FRONT TRUNNION A . Rear trunnion must be moved TOWARD the combination square if there is a space between marked tooth and end of square in step 4 , B , Rear trunnion must be moved AWAY from the square if marked tooth pushes square out of position in the groove . REAR - TRUNNION SCREWS 7 . Loosen all three screws that hold the rear trunnion and all three screws that hold the front trunmon . NOTE : All six screws can be reached through back of saw . Use a 9 / 16 - in . wrench , To reach left - hand front trunnion screw , tilt blade to 45 ° . After loosening screws reposition blade at 90 ° . / l FRONT - TRUNNION SCREWS EDGE OF TRUNNION OCK Using a wood block and mallet as shown , move rear trunnion to right or left as required to realign the blade . If necessary , shift front trunnion in similar manner ; but do NOT move front trunnion unless necessary . Recheck _ 1 the alignment w th the square , then secure y ret ghten all six trunmon screws . ' PLACE BLOCK HERE - - OR HERE EDGE OF REAR OF SAW CRADLE BLADE TILT , OR SQUARENESS OF BLADE TO TABLE gO ° ( SQUARE ) and 45 ° ( BEVEL ) STOP COLLARS . When the bevel oointer is pointing directly to the " 0 " mark on the bevel scale , the sawblade should make a SQUARE cut 90 ° to the table . To check for SQUAR EN ESS : WARNING : FOR YOUR OWN SAFETY , TURN SWITCH " OFF " AND REMOVE PLUG FROM POWER SOURCE OUTLET . 1 . Raise blade all the way UP . . . raise blade guard 2 . Place the square against blade . Make sure square is not touching the TIP of one of the saw TEETH . 3O
Page: 31

3 . Operate the tilt - lock handle ( COUNTERCLOCKWISE ) to loosen the tilt clamp screw . 4 . NOTE : Handle is spring loaded for engagement with screw head - must be pushed inward for disengagement whenever necessary to obtain a new grip on screw head . 5 . Rotate tilt handwheel CLOCKWISE a few turns to till blade . Now rotate handwheel COUNTERCLOCKWISE until it stops . Blade should now be square with table and pointer should point to " 0 " . If blade is SQUARE to table ; A . Check pointer F POINTER DOES NOT point to the " O " mark on the bevel scale ; A . Remove Elevation Handwheel . B . Loosen screw and adjust pointer . . . using medium screwdriver . C . Install Elevation Handwheel . If blade is NOT SQUARE to table . . , the 90 ° LIMIT STOP must be ADJUSTED . 1 . Using a medium size screwdriver , loosen BOTH setscrews in 90 ° STOP COLLAR . NOTE : If you can't reach the setscrews , turn the TILT NANDWHEEL slightly . 2 . ROTATE the STOP COLLAR moving it all the way to the end of TILT SCREW . ( to the right ) . 3 . TILT blade RIGHT or LEFT . . . checking with your square until blade is square to table . COLLAR 4 . ROTATE STOP COLLAR moving it to the right until it stops . . . TIGHTEN the setscrews . 5 . Check POINTER . If it DOES NOT point to the " O " mark on the bevel scale . . . A . Remove Elevation Handwheel . B . Loosen screw and ad ) ust pointer . . . using medium screwdriver . C . Install Elevation Handwheel . 45 ° POSITION TILT blade to LEFT as far as it will go . It will stop when the PIVOT NUT is against the 45 ° STOP COLLAR . A , Place an ACCURATE square against blade . Make sure square is not touching the TIP of one o { the saw TEETH . If blade is 45 ° to table ; A . Check pointer . If POINTER DOES NOT point to the 45 ° mark on the scale ; POINTER points to 45 ° mark . A . Remove Elevation Handwheel . C . Install Elevation Handwheel . B , Loosen two screws on scale and adjust scale until 31
Page: 32

If b ! ade is NOT 45 ° to table . . , the 45 ° STOP COLLAR and SCALE must be ADJUSTED , _ 1 Remove Elevation Handwheel . _ 0 ° 2 . Using a small size screwdriver , reach thru curved slot in front trim panel and loosen BOTH setscrews in 45 ° STOP COLLAR . 3 . ROTATE the STOP COLLAR moving it IN or OUT TILTNOthTeE'Hf : AYN ° uDWcHaEnE'tLsre , , agchht , y . the setscrews ' turn _ _ _ i ! _ and TILT blade RIGHT or LEFT . . . checking with your square until blade is 45 ° to table . NOTE : If you can't reach the setscrews , turn TILT 4 . TIGHTEN the setscrews . _ _ _ l _ I _ . . _ . jI - _ Y HANDWHEEL slightly . 5 . Loosen two screws on scale and adjust scale until _ \ _ ' _ T - _ / fj POINTER points to 45 ° mark . \ / 6 . Install Elevation Handwheel . TI LT MECHANISM The handwheel should turn freely without binding . The turning action can be adjusted by tightening or loosening the screws in the bearing retainer . NOTE : Tilt'Handwheel must be removed to adjust . When adjusting the screws in the bearing retainer , hold the nut inside using a 3 / 8 in . wrench . / t iO SCREWS I II IIII IIIII MAINTENANCE WARNING : FOR YOUR OWN SAFETY , TURN SWITCH 2 . Rotate pawl toward rear of spreader so that teeth are " OFF " AND REMOVE PLUG FROM POWER SOURCE above top of spreader . OUTLET BEFORE MAINTAINING OR LUBRICATING 3 . Hold spreader with left hand and place pawl over corner YOUR SAW . of workbench . Do not allow sawdust to accumulate inside the saw . 4 . Using a small round file ( Smooth Cut ) sharpen the teeth Frequently blow out any dust that may accumulate inside the saw cabinet and the motor . Frequently clean your cutting tools with Craftsman Gum and Pitch Remover . , ) A coat of automobile - type wax applied to the table will help to keep the surface clean and allow workpieces to slide more freely . If the power cord is worn or cut , or damaged in any way . have it replaced immediately . Make sure the teeth of the ANTIKICKBACK pawls are always sharp . To sharpen : 1 . Remove blade guard . 32
Page: 33

LUBRICATION The following parts should be oiled occasionally with SAE No . 20 or No . 30 engine oil . 1 . Tilt screw threads and pivot nut . ( First Clean with Craftsman Gum & Pitch Remover . ) 2 . Elevation screw threads and pivot nut . ( First Clean with Craftsman Gum & Pitch Remover . ) 3 . Cradle bearing points . 4 . Bearing points in guard assemblv , miter gauge and rip fence . . = j _ l ; , GUARD Q , _ _ ITER GUAGE i BEARING POINTS RECOMMENDED ACCESSORIES ITEM CAT . NO . ITEM CAT . NO . Work Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 2481 Steel Legs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 22235 Steel Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 22214 7 In . Dia . Adjustable Dado Head . . . . . . . . . . . . . . 9 - 3263 7 In . Dia . Dado Head . . . . . . . . . . . . . . . . . . . . . . . 9 - 3257 Retractable Caster Set . . . . . . . . . . . . . . . . . . . . . 9 - 22208 Sanding Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 22723 Solid Table Extension . . . . . . . . . . . . . . . . . . . . . . 9 - 29957 Miter - Gauge Stop Rods . . . . . . . . . . . . . . . . . . . . . 9 - 29924 7 In . Molding Head Set . . . . . . . . . . . . . . . . . . . . . . 9 - 3217 Miter - Gauge Hold - Down Clamp . . . . . . . . . . . . . . 9 - 29928 7 In . Molding Head Set . . . . . . . . . . . . . . . . . . . . . . 9 - 3218 Taper Jig . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 3233 7 In . Molding Head . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 3214 Universal Jig . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 3235 Molding / Dado Insert for 7 In , Power Tool Know How Handbooks Dia . Molding or Dado Head . . . . . . . . . . . . . . . . . 9 - 29997 Table Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 2918 Work Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 2480 33
Page: 34

TROUBLE SHOOTING WARNING : FOR YOUR OWN SAFETY , TURN SWITCH " OFF " AND ALWAYS REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE TROUBLESHOOTING . TROUBLE SHOOTING - - GENERAL REMEDY TROUBLE , PROBABLE CAUSE 1 . Discard Blade and use a different blade . Excessivevibration . 1 _ Blade outof balance . | 2 . Replace as Indicated . 2 . Damaged V - Belt Pulleys or poor belt . I . See " Adjustments " section " Miter Gauge , " Cannot make square ' 1 . Miter gauge not adjusted Cut when crosscutting , properly . Cut binds , burns or 1 . Dull blade with improper 1 . Sharpen or replace blade . stalls motor when tooth set . ripping , 2 . Blade is Heeling . 2 . See " Adjustments " section , " Heeling Adjustment . 3 . Make sure concave or hollow side is facing 3 . Warped board . " down , " feed slowly . 4 . See " Assembly " section , " Aligning Rip Fence " 4 . Rip fence not parallel to blade , 5 . Spreader out of 5 . See " ' Assembly ' " section " Installing Blade Guard . ' " alignment Cut nottrue at 90 ° 1 . Stop collars not properly 1 . See " Adjustments " section , " Blade Tilt , or " Squareness of Blade to Table . " or 45 ° positions , adjusted . 1 . See " ' Maintenance and Lubrication " section . Tilt and elevating 1 . Sawdust on threads of tilt handwheel turn hard . screw or elevating screw . 2 . See " Maintenance " section 2 . Bearing retainers " Tilt and Elevation Mechanism , " to tight . TROUBLE SHOOTING - - MOTOR NOTE : Motors used on wood - working tools are particularly susceptible to the accumulation of sawdust and wood chips and should be blown out or " ' vacuumed " _ frequently to prevent interference with normal motor ventilation . TROUBLE PROBABLE CAUSE REMEDY Excessive noise , 1 . Motor . 1 . Have motor checked by qualified service technician . Repair service is available at your nearest Sears store . 1 . Circuit overloaded with 1 . Do not use other appliances or motors on Motor fails to develop same circuit when using the saw . full power . NOTE : lights , appliances and other motors . LOW VOLTAGE : ( Power output of motor decreases 2 . Undersize wires or cir _ , uit 2 . Increase wire sizes , or reduce length of wiring . rapidly with decrease in voltage at motor terminals . tOOlong . See " Motor SpeCification and Electrical For example , a reduction Requirements " section , of 10 % in voltage causes 3 . General overloading of 3 . Request a voltage check from the power company . a reduction of 19 % in power company facilities . maximum power output of which the motor is capable , and a reduction of 20 % in voltage causes a reduction of 36 % in maximum power output . } 34
Page: 35

TROUBLE SHOOTING - - MOTOR ( Continued ) TROUBLE PROBABLE CAUSE REMEDY Motor starts slowly 1 , Low voltage will not 1 . Request voltage check from the power company . or fails to come up trip relay . to full speed . 2 . Windings burned out 2 . Have motor repaired or replaced . or open . 3 . Starting relay not 3 . Have relay replaced . I operating . Motor overheats . 1 . Motor overloaded . 1 . Feed work slower into blade . 2 . I mproper cooling . ( Air 2 . Clean out sawdust to provide normal air circulation restricted circulation through motor . See " Maintenance and Lubrication " section , , through motor due to sawdust , accumulating inside of saw ) . 1 . Burned switch contacts Starting switch in 1 . Have switch replaced and request a voltage ( ' heck motor will not ( due to extended from the power company , operate . hold - in periods caused by low line voltage , etc , ) 2 . Shorted capacitor 2 . Have capacitor tested and replace if defective . ( when equipped ) 3 . Loose or broken 3 . Have wiring checked and repaired . connections . Motor stalls 1 . Starting switch not 1 . Have switch replaced . ( resulting in blown operating . fuses or tripped 2 . Voltage too low to permit 2 . Request voltage check from the power company . circuit breakers ) . motor to reach operating speed . 3 . Fuses or circuit breakers 3 . Install proper size fusesor circuit breakers . do not have sufficient capacity . 1 . Motor overloaded , 1 . Feed work slower into blade . Frequent opening of fusesor circuit 2 . Fusesor circuit breakers 2 , Install proper size fuses or circuit breakers . breakers . do not have sufficient capacity . 3 . Have switch replaced . 3 . Starting switch not operating ( motor does not reach speed ) , 35
Page: 36

PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAW MODEL NO . 113.298141 , 113.298031 & 113.298151 1 7 8 9 14 10 16 6 3 20 19 i o , 36 35 - I 28 29 30 31 32 31 ! 27 26 25 Figure I 33
Page: 37

PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAW MODEL NO . 113.298141 , 113.298031 & 113.298151 Always order by Part Number - not by Key Number . FIGURE 1 PARTS LIST Key Part Key Part No . No . Description No . No . Description 25 STD 511107 * Screw , Pan I - i _ l . 10 - 32 x 3 / 4 1 62579 Guard Assembly ( See Fig . 5 ) 26 STD 551210 * Lockwasher , External No . 10 2 STD 522506 * Screw , Hex Hd . 1 / 4 - 20 x 5 / 8 27 62689 3 STD 551225 * Lockwasher , External 1 / 4 Handwheel Assembly 28 STD 511103 * Screw , Pan Hd . 10 - 32 x 3 / 8 4 STD 541025 * Nut , Hex 1 / 4 - 20 29 60354 Nut , Speed No . B 5 STD 523110 * Screw , Hex 5 / 16 - 18 x 1 30 62701 6 62541 Bar , Fence Rear Panel , Front 31 STD 810805 * Screw , Pan Hd . Ty " AB " No . 8 x I / 2 7 STD 551231 * Lockwasher , External 5 / 16 32 62702 Scale , Adjustable Bevel 8 STD 541031 * Nut , Hex 5 / 16 - 18 33 62700 Base 9 60388 Nut , Self - threading 34 60252 Guard , Belt 10 62703 Insert Assembly , ( Includes Key No . 11 & 12 ) 35 60255 Clip , " S ' " 11 62718 Clip , Retaining 36 STD 601105 * Screw , Pan Hd . Ty " T " 10 - 32 x 1 / 2 12 STD 501102 * Screw , Locking Set 10 - 32 x 3 / 16 ( , } 37 60253 Support , Belt Guard 13 133645 Screw , Flat Hd . 10 - 32 x 1 Bracket , Support 14 62748 Rod , Separation ( Includes Key No . 9 ) 38 60254 39 454896 * Screw , Hex Hd . , 3 / 8 - 16 x 1 / 2 15 62493 Insert , Exact - I - Cut 40 STD 551237 * Lockwasher , External 3 / 8 16 62705 Fence Assembly , Rip ( See Fig . 3 ) 41 71165 Tie , Wire 17 62710 Tape , Fence 42 STD 541411 Nut , Lock 10 - 32 18 62709 Bar Assembly , Fence Guide 43 62618 + Motor ( Model 113.298031 ) ( Includes Key No , 17 ) _ Screw , Hex Hd . 5 / 16 - 18 x 3 / 4 43 62680 + Motor ( Model 113.298151 ) 19 STD 523107 62750 _ Washer , 21 / 64 x 5 / 8 x 1 / 16 Bag of Loose Parts ( Not Illustrated ) 20 STD 551031 62539 ( Includes Bag62751 ) 21 Spacer , Fence Guide Bar 62751 60381 Switch Assembly , Box ( See Fig . 6 ) Bag of Loose Parts ( Not Illustrated ) 22 62753 Owners Manual ( Not Illustrated ) * Screw , Hex , 5 / 16 - 18 x 1 - 3 / 4 23 STD 523117 24 62704 GaugeAssembly , Miter ( See Fig . 4 ) * Standard Hardware Item - - May Be Purchased Locally . NOTE : Shippmg and handling charges for standard hardware items ( identified by * ! such as nuts , screws , washers , etc . , make buying these items by mail uneconomical . To avoid shipping and handling charges , you may obtain most of these locally . Stock Item - - May be secured through the hardware department of most Sears Retail Stores or Catalog Order Houses .
Page: 38

PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAW MODEL NO . 113.298141 , 113.298031 & 113.298151 4 5 6 7 1 2 3 9 10 18 19 20 12 13 65 I 14 21 64 1 62 u t 25 I 45 31 41 4O 44 38 37 36 43 Figure 2
Page: 39

PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAW MODEL NO . 113.298141 , 113.298031 & 113.298151 FIGURE 2 PARTS LIST Key Part Key Part No . No . Description No . No . Description 34 STD 302111 * O - Ring 62587 Support , Spreader 1 35 62697 Screw , Lift 60204 Screw , Thumb 5 / 16 - 18 x 1 2 36 62699 Pointer 3 STD 571812 * Pin , Roll 3 / 16 x 1 - 1 / 4 37 8TD 601103 * Screw , Pan Hd . Ty " ' T ' " 10 - 32 x 3 / 8 4 STD 523106 * Screw , Hex Hd . 5 / 16 - 18 x 5 / 8 38 STD 551210 * Lockwasher , External No . 10 5 STD 523110 * Screw , Hax Hd . 5 / 16 - 18 x 1 39 62489 Cradle ( Includes Key No's . 42 and 43 ) * Lockwasher , External 5 / 16 6 STD 551231 40 30509 _ Washer , End Play ( . 005 Thick ) 7 62292 Support , Guard 41 30767 Washer , End Play ( . 610 Thick ) 8 STD 541031 * Nut , Hex 5 / 16 - 18 Link 42 62312 * Bolt , Carriage 5 / 16 - 18 x 3 / 4 9 STD 532507 43 6527 Ring , Retaining 3 / 4 10 60206 * Screw , Hex Ind . Wash . Hd . 44 STD 328022 1 / 4 - 20 x 1 - 1 / 2 * Pulley , 5 / 8 Bore ( Includes Set Screw ) 45 STD 304410 60205 Spring * Belt , V 1 / 2x 41 11 * Washer , 380 x 47 / 64 x 3 / 32 46 30419 Housing , Arbor Assembly ( Includes Key No's . 12 STD 551037 44 , 47 , 49 , 50 , 51,52 , 53 , 54 ) 63011 13 Washer , Knob Clamp 47 STD 600803 * Screw , Pan Hd . Ty " T " 8 - 32 x 3 / 8 62295 Spacer 14 _ O 30426 Table , Trunnion 15 49 3508 Retainer , Arbor Bearing 16 62696 Table , 10 In . Saw 50 37158 Ring , Retaining 5 / 8 17 60175 + Blade ; Saw 10 In . 51 3509 Bearing , Saw Arbor 18 62498 Collar , Blade 52 30420 Housing , Arbor 6362 Nut , Arbor 19 53 STD 580025 * Key , Woodruff 3540 Wrench , Arbor 20 54 6532 Arbor ( Includes Key No's . 31 , 50 , 53 ) 21 62437 Retainer , Bearing 55 37825 22 62698 Screw , Tilt Support , Motor Base 56 37824 Base , Motor 37900 23 Collar , Stop 57 37823 Pin , Hinge STD 523710 Screw , Hex Hd . 3 / 8 - 16 x 1 24 58 STD 581037 Ring , Retaining 3 / 8 STD 551237 Lockwasher , External 3 / 8 25 59 37836 Wrench , Hex L 3 / 32 37899 Nut , Tilt 26 60 37887 Wrench , Hex L 1 / 8 63054 Ring , Retaining 314 27 6t 37837 Wrench , Hex L 5 / 32 Spring , Clamp Screw ' . , 28 37828 62 30628 Screw , Pivot Arm Handle , Clamp Screw 29 18 63 6423 Washer , Spring 37829 Screw , Clamp 30 64 STD 551025 * Washer , 17 / 64 x 47 / 64 x 1 / 16 STD 581062 Ring , Retaining 5 / 8 31 65 62585 Rod , Spreader Washer . 629 x 7 / 8 x 1 / 64 32 37838 60178 Washer , Spring 33 Stock Item - May be secured through the Hardware Department Standard Hardware Item - May Be Purchased Locally . of most Sears Retail Stores or Catalog Order Houses .
Page: 40

PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAW MODEL NO . 113.298141 , 113.298031 & 113.298151 9 10 11 4 5 2 3 I 13 FIGURE 3 - - 62705 FENCE ASSEMBLY Key { Part No . No . Description - 62705 Fence Assembly , Rip 1 62693 Plug , Button 2 62692 Knob ( Includes Key No . 1 ) 3 STD 551031 * Washer , 21 / 64 I . D . 4 62711 Indicator , Fence 5 60049 * Screw , Pan Hd . Type " ' T ' " 4 - 40 x 3 / 16 Head , Fence 6 62527 423350 Screw , Seres 3 / 8 _ 16 x I / 2 8 62582 Channel , Fence 9 STD 600805 * Screw , Pan Hd . Type " T " & 32x 1 / 2 10 62528 Spring , Fence Lock Lock , Rear Fence 11 3625291 12 625 Roller , Rear Fence 1 _ 625 _ 3 Rod , Pence Lock 14 • 62533 , Spring , Head Alignment ( Includes Key No . 17 ) 15 STD 551210 * Lockwasher , External No . 10 16 STD 611005 _ Screw , Type " A ' , Hex Ind . SI . Wash . Hd . No . 10 x 1 / 2 17 62532 • Pad , Alignment * Standard Hardware Item - May Be Purchased Locally . 4O
Page: 41

PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAW MODEL NO . 113.298141 , 113.298031 & 113.298151 5 1 3 1 12 14 11 1 \ 10 9 FIGURE 4 - - 62704 MITER GAUGE ASSEMBLY FIGURE 5 - 62579 GUARD ASSEMBLY . = Part Keyo . Key Part N DescriptiOn No . No . Description 62579 _ Guard Assembly , Saw - 62704 + Gauge Assembly , Miter 60297 _ ' _ . _ lut , Push 1 62693 Plug , Button 62391 _ q 1 / 4 x 1 - 1 / 2 " 2 62692 Knob , Miter Gauge 62395 Support , Guard ( Includes Key No . 1 ) 62389 Guard , Saw 3 STD 551031 * Washer , Plain , 21 / 64 x 1 x 1 / 16 5 62390 Pin , 1 / 4 x 1 - 3 / 4 " 37893 Gauge , Miter 6 STD 551025 * Washer , 17 / 64 x 5 / 8 x 1 / 16 " STD 510803 * Screw , Pan Hd . 8 - 32 x 5 / 16 62520 Sp _ er , Pawl 135 Indicator Pawl 62396 37895 Block , Miter Gauge Indicator 62580 Spreader , Assembly Blade 8 37896 Pin , Miter Gauge Stop 6241O Pin , I / 4 x 1 " 9 9417295 * screw , Pan Hd . , STD 571810 * Pin , Roll , 3 / 16 x 15 / 16 " w / Lockwasher , 8 - 32 x 5 / 8 1 62519 Spring , Pawl 62230 10 Rod Assembly , Miter Gauge , Consisting of Items 11 , 12 , 13 11 8TD 541231 * Nut , Hex . , 5 / 16 - 18 12 62225 Stud , Clamp 13 62383 Stud , Pivot 14 60288 Screw , Locking Set 1 / 4 - 20 x 3 / 8 Standard Hardware Item - May Be Purchased Locally . + Stock Item - May be secured through the Hardware Department of most Sears Retail Stores or Catalog Order Houses . 41
Page: 42

PARTS LJST FOR CRAFTSMAN 10 INCH TABLE SAW MODEL NO . 113.298141 , 113.298031 & 113.298151 5 6 1 3 4 2 \ \ FIGURE 6 - - ON / OFF POWER OUTLET 60381 Kevl • Paff - No . No . Description J 60381 • On / Off Power OutletComplete 1 60375 Cord , Molded 2 60380 Housing , Switch : 3 60256 Key , Switch 60374 _ i 4 Switch , Locking 5 60377 Cover , Switc h 6 448007 Screw , pn Hd . No . 6 x 3 / 4 = Does Not Include Kev No . 3 Order Separately If Required . ; 42 • . . . . . . . . . . . :
Page: 43

PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAW MODE L NO . 113.298141 , 113.298031 & 113.298151 4 5 5 4 2 12 2 , ' / / 4 . " - - - . 3 7 8 9 - FIGURE 9 - TABLE EXTENSION SUPPLIED WITH MODEL 113.298031 AND 113.298151 FIGURE 8 - - LEGS SUPPLIED WITH 113.298031 AND 113.298151 ONLY Key Part No . No . Description Part Key i i = = No , - 62589 No . Description tExtension Assembly , Complete 1 60323 Screw , Serrated Truss Hd . , 1 60314 Screw , Serrated Truss Hd . 1 / 4 - 20 x 5 / 8 1 / 4 - 20 x 1 " " 2 62552 Leg 2 62590 Extension 3 62554 Stiffener , Side 3 62549 Bracket , Corner Support 4 STD 551225 * Lockwasher , Ext . 1 / 4 4 STD 541025 * Nut , Hex 1 / 4 - 20 5 STD 541025 * Nut , Hex 1 / 4 - 20 5 STD 551225 * Lockwasher , Ext . 1 / 4 6 62553 Stiffener , End 6 62550 Bracket , Corner Stiffener 7 STD 541250 * Nut , Hex 1 / 2 - 13 7 STD 523112 * Screw , Hex Hd . 5 / 16 - 18 x 1 - 1 / 4 8 803835 Foot , Leveling 8 STD 551131 * Lockwasher , Ext . 5 / 16 HARDWARE FOR ATTACHING LEGS TO SAW . 9 STD 541O31 * Nut , Hex 5 / 16 - 18 9 STD 523112 * Screw , Hex Hd . 5 / 16 - 18 x 1 - 1 / 4 62745 Bag of Loose Parts ( not illustrated ) 10 STD 551031 Washer , 11 / 32 I . D . 11 STD 551131 * Lockwasher , Ext . 5 / 16 12 STD 541031 * Nut , Hex 5 / 16 - 18 62752 Bagof Loose Parts For Legs ( not illust . * Standard Hardware Items May be Purchased Locally . • Bag contains all Loose Parts for Extensions . t Stock Item - May be secured through the Hardware Department of most Sears retail stores or catalog order house . 43
Page: 44

Sears I owners 10 INCH TABLE SAW manual SERVICE Now that you have purchased your 10 - inch table saw should a need ever exist for repair parts or service , simply contact any Sears Service Center and most Sears , Roebuck and Co . stores . Be sure to provide all pertinent facts when you call or visit . MODEL NO . 113.298141 SAW ON LY The model number of your 10 - inch table saw will be found on a plate attached to your saw , at the left - hand side of the base . 113.298031 SAW WITH LEGS TWO TABLE EXTENSIONS AND MOTOR 113.298151 SAW WITH LEGS WHEN ORDERING REPAIR PARTS , ALWAYS GIVE THE ONE TABLE EXTENSION FOLLOWING INFORMATION : AND MOTOR PART NUMBER PART DESCRIPTION HOW TO ORDER MODEL NUMBER NAME OF ITEM REPAIR PARTS 10 - INCH TABLE SAW 113.298141.113.298031 or113 . 298151 All parts listed may be ordered from any Sears Service Center and most Sears stores . If the parts you need are not stocked locally , your order will be electronically transmitted to a Sears Repair Parts Distribution Center for handling . ! I Sold by SEARS , ROEBUCK AND CO . , Chicago , IL . 60684 U . S . A . Part No . 62753 Form No , SP4445 - 4 Printed in U . S . A . 10180
Search in Table Saw on ebay
"