Home | Register Login | Wanted Manuals | MarketPlace | Members Area | Manuals Manufacturer Directory | UPC Lookup | Information Pages | Policy


Back To Craftsman Table Saw       Model: 113.298762 or 113298762 Craftsman 10 Inch Table Saw
Regular Text Search or Search by Model Number

Register / log-in to add to your Hammerwall Collection.
Manual Location


This is a partial text extraction from the pdf, to download the pdf, click the Manual tab. If you want to search this text, hold control and F, and type the word you are looking for.

Page: 1

Save This Uanuam For Future Reference MODEL NO'S , 113o298722 113.298762 SAW WITH LEGS TWO CAST IRON TABLE EXTENSIONS MOTOR AND QUICK RELEASE RiP FENCE Serial Number Modelandserialnumbermaybefound SEAFW / CRRFTSMRH at theleft - handsideofthe base . You should record both model and serial number in a sale place for future use . IO . INCH TABLE SAW FOR YOUR • assembly SAFETY : Read ALL ooperating INSTRUCTIONS ° repair parts CAREFULLY . _ , , illll Sold by SEARS , ROEBUCK AND CO . , Chicago , IL . 60684 U . S . A . Part No . SP5627 Printed in U . S . A .
Page: 2

FULLONEYEARWARRANTYONCRAFTSMATNABLESAW If wlth | noneyearfromthedaleof purchaseth , isCraftsmaTnableSawfallsdueto a defect in mstedal orwo _ manshlp , Sears will repair it , free of charge . This warranty applies only while this product is in use inthe United States . WARRANTY SERVICE IS AVAILABLE BYSIMPLY CONTACTINGTHE NEAREST SEARS SERVICE CENTER / DEPARTMENT THROUGHOUT THE UNITED STATES . THIS WARRANTY APPLIES ONLY WHILE THiS PRODUCT iS USEDIH THE UNITED STATES . This warranty gives you specific legal rights , and you mayalso have other rightswhich vary from state to state . SEARS , ROEBUCK AND CO . , D / 817 WA Hoffman Estales , IL 60195 v . . . . . safety instructions for table saw 4 . GROUND THE SAW - This saw has an approved 3 - Safety is a combination of common sense , staying alert and knowing how your table saw works . Read this conductor cord and a 3 - prong grounding type plug . manual to understand this saw . The plugfits grounding type outlets desig ned for 120 volt 15 amp circuits . The green conductor inthe cord BEFORE USING THE SAW isthegrounding wire . To avoid electrocution , NEVER connect the green wire to a live terminal . serious , permanent Injury , do not plug the saw In 5 . To avoid injuryfrom electrical shock , make sure your until the following steps have been satisfactorily fingers do not touch the plug's metal prongs when completed . plugging in or unpluggingthe saw . 6 . To avoid back injury , get help or use recommended casters when you need to move the saw . Always get Guard , Spreader , Anti - Kickbackdevice , Miter Gauge , help if you need to lift the saw . Hold the saw close to Fence , Table Insert and Blade Elevation and Bevel your body . Bend your knees so you can liftwith your Controls . ( See page 25 ) legs , not your back . 7 . NEVER STAND ON TOOL . Serious injury could occur ifthe tool tips or you accidentally hitthe cutting 4 . Review of the maintenance methods for this saw . tool . Do not store anything above or near the tool ( See page 43 ) where anyone might stand on the tool to reach them . Read the DANGER label found onthe front of the saw , BEFORE EACH USE : anything . 2 . To avoid injury from unexpected saw movement : B . Check for alignment of moving parts , binding ofd A . Put the saw on a firm level surface where there is moving parts , breakage of parts , mounting , an i • _ ua r _ j . p gL , _ rd down and i _ 7 . When rtppixtg . use push stick when 9 . When riPPing , use push blOCk and 10 . Turn _ 0owex off and walt fo _ blade II : _ _ goggles that meet place f _ r through cut _ fence , Is set 2 _ nches or more from auxiliaw fence wherl fence _ s set to stop before adjusting or ANSI 2 : 871 standa _ s . 5 . Do not do freehamd cuts . bla6 _ . between V2 and 2 irt _ hes from E 3 . _ nottDroot macfi around Or over saw 6 . Keep hands out of path of saw 8 . Know how to reduce the risk af blade . Do not nlake rip cuts | narrower than _ / 2 inch _ _
Page: 3

E . REMOVE ADJUSTING KEYS AND WRENCHES . B . Dress for safety : Form habit of checking for and removing keys and 1 . Do not wear loose clothing , gloves , neckties or adjusting wrencheslrem tool before turning it on . jewelry ( dngs , wristwatches ) . They can get F . To avoid injury from jams , slips or thrown pieces caught and draw you into moving parts . ( kickback and throwback ) : 2 . Wear nonslip footwear . 1 . USE ONLY " RECOMMENDED ACCESSO - 3 . Tie back long hair . RIES " ( See page 43 ) . Follow the instructions 4 . Roll long sleeves above the elbow . that come with the accessories . Using other ac - 5 . Noise levels vary widely . To avoid possible cessories may be dangerous . hearing damage , wear ear plugs or muffs when 2 . Choose the right blade or cutting accessory for using saw for long periods of time . the material and the type of cutting you plan to do . 6 . Any power saw . can throw foreign objects into the eyes . This can cause permanent eye 3 . Never use grinding wheels , abrasive cut - off damage . Wear safety goggles ( not glasses ) wheels , friction wheels ( metal slitting blades ) that comply with ANSI Z87 . 1 ( shown on pack - wire wheels orbuffing wheel . They can fly apart age ) . Everyday eyeglasses have only impact explosively . resistant lenses . They are not safety glasses . 4 . Choose and inspect your cutting tool carefully . Safety goggles are available at Sears retail a . To avoid cuttingtoolfailureand thrownshrap - catalog stores . Glasses or goggles not in com - nel ( broken pieces of blade ) , use only 10 " or pliance with ANSI Z87 . 1 could seriously hurt smaller blades or other cutting tools marked you when they break . for speeds of 3450 rpm or higher . WEAR YOUR b . Always use unbroken , balanced blades designed to fit this saw's 5 / 8 inch arbor . c . When thru - sawing ( making cuts where the blade comes through the workpiece top ) , always use a 10 inch diameter blade . This keeps the spreader in closest to the blade . d . Do not overtighten arbor nut . Use arbor 7 . For dusty operations , wear a dust mask along wrenches to " snug " it securely . with the safety goggles . e . Use only sharpbladeswith properly setteeth . C . Inspect your workpiece . Make sure there are no Consult a professional blade sharpenerwhen nails or foreign objects in the part of the workplece in doubt . to be cut . f . Keep blades clean of gum and resin . D . Plan your cut to avoid KICKBACKS and THROW - 5 . Adjust table inserts flush with the table top . BACKS - when a part or all of the workpiece binds NEVER use the saw without the proper insert . on the blade and is thrown violently back toward the front of the saw . 6 . Make sure all clamps and locksare tight and no parts have any excessive play . 1 . Never cut FREEHAND : Always use either a Rip Fence , Miter Gauge or fixture to position 2 . Keep work area clean and guide the work , so itwon't twist , bind on the A . Cluttered areas and benches invite accidents . blade and kickback . Floor must not be slippery from wax or sawdust . 2 . Make sure there's no debris between 1ne work - B . To avoid burnsor other fire damage , never use the piece and its supports . saw near flammable liquids , vapors or gases . 3 . When cutting Irregularly shaped workpieces , C . To avoid injury , don't do layout , assembly , or setup plan your work so it will not slip and pinch the work on the table while the blade is spinning . It blade : could cut or throw anything hitting the blade . a . A piece of molding , for example , must lieflat Plan ahead to protect your eyes , hands , face , ears . or be held by a fixture or jig that wiU not let it AVOID ACCIDENTAL STARTING - Make sure twist , rock or slip while being cut . Use jigs or switch is " OFF " before plugging saw in . fixtures where needed to prevent workpiece 3 . Plan your work shifting . A . USE THE RIGHT TOOL - Don't force toot or b . Use a different , better suited type of toot for work that can't be made stable . attachmentto do a job it was not designed for .
Page: 4

or vibrates a lot , stop immediately . Turn the saw off . 4 . Use extra caution with large , , very small or awkwardworkpisces . Unplugthe saw . Do not restart untilfinding andfixing the problem . a . Use extra supports ( tables , sawhorses , block , etc . ) for any workpieces large enough to tip 2 . Make sure the top of the arbor or cutting tool turns toward the front of the saw . when not hell down to thetable top . NEVER uSe another person as a substitute for a 3 . Set the cutting tool as low as possible for the cut table extension , or as additional support fora you're planning . workpiece that is longer or wider than the 4 . KEEP CHILDREN AWAY . All visitorsshould be kept basic saw table , orto help feed , support or a safe distance fromwork . Make sure bystanders are pull the workpisce . clear of the saw and workplece . b . Never confine the piece being cut off , that is , 5 . Let the blade reach full speed before cutting . the piece NOT againstthe fence , mitergauge 6 . DON'T FORCE TOOL . It will do the job better and or fixture . Never hold it , clamp it , touch it , or safer at its designed rate . Feed the workpiece intothe use length stops against it . It must be free to blade only fast enough to let it cut without bogging move . Ifconfined , itcouldgetwedged against down or binding . the blade and cause a kickback or throw - 7 . Before treeing any jammed material back . A . Turn switch " OFF " . c . Never cut morethan one workpiece at a time . B . Unplug the saw . d . Never turn your table saw " ON " before clear - C . Wait for all moving pars to stop . ing everything except the workpiece and related support devices off the table . D . Check blade , Spreader and Fence forproper align - ment before starting , again . 4 , Planthawayyouwill pushtheworkplecethrough 8 . To avoid throwback of cut off pieces ; A . NEVER pull the workpleo _ through . Start and finishthe cut from the front of the table saw . A . Use the Guard assembly . B . NEVER put your fingers or hands in the path of B . To remove loose pieces beneath ortrapped inside the sawblade or other cutting tool . the guard : C . N EVER reach In back ofthe cuttingtoolwith either 1 . Turn saw " OFF " . hand to hold down or support the workpiece , 2 . Remove switch key . remove wood scraps , or for any other reason . 3 . Wait for blade to stop before liftingthe Guard . D . Avoid hand positions where a sudden slip could ADDITIONAL INSTRUCTIONS FOR cause fingers or hand to move into a sawblade or other cutting tool . RIPTYPE CUTS E . DON'T " OVERREACH . Always keep good footing 1 . NEVER use the Miter Gauge when ripping . and balance . 2 . Use a Push Stick whenever the fence is 2 or more F . Push the workpisce against the rotation of the inches from the blade . When thru - sawing , use an blade . NEVER feed material into the cutting tool AuxiliaryFence and Push Blockwhenever the Fence from the rear of the saw . mustbebetween 1 / 2 and2 inchesof the blade . Never G . Always push the workpiece all the way past the thru - saw rip cuts narrower than 1 / 2 inch . ( See = BA - sawblade . SIC SAW OPERATION - USING THE RIP FENCE " section . ) H . As much as possible , keep your face and body to one skJeof the sawblade , outof line with apossible 3 . Never rip anything shorter than 10 " long . kickback or throwback . 4 . When using a Push Stick or Push Block , the trailing end of the beard must be square . A Push Stick or I . NEVERtum the saw = ON " before cieadngthe table of all tools , wood scraps , etc . , except the work - Blockagainst an uneven end could slip off orpush the piece and related feed or support devices for the work away from the Fence . cutp nned . 5 . A FEATHERBOARD can help guide the workpiece . J . AVOID ACCIDENTAL STARTING - Make sure See " BASIC SAW OPERATION - USING THE RIP switch is = OFF " before plugging saw in . FENCE . " Always use Featherboards for any non thru rip type cuts . WHENEVER SAW BLADE iS SPINNING WARNING : Don't let familiarity ( gained from fie - I tion of a second Is enough to cause a Severe + + + o + , J 5 / 16 " APART Injury . 4 - 1 / 2 ' + - 5 " 1 . Before actually cuttingwith the saw , watcl _ it while it runsfor a short while , if it makes an unfamiliar noise 4
Page: 5

BEFORE STARTING 2 . An auxiliary wood facing attached to the Miter Gauge can help prevent workpiece twisting and throwbacks . 1 . To avoid kickbacks and slips into the blade , make Attach it to the holes provided . Make the facing long sure the Rip Fence is parallel to the sawblade . enough and big enough to support your worK . Make 2 . Check the anti - kickback pawls . ( See " BASIC SAW sure , however , it will not interfere with the Sawblade OPERATION - USING THE RIP FENCE . " ) The Guard . ( See page 26 ) Pawls must stop a kickback once it has started . 3 . Use jigs or fixtures to help hold any piece too small to Replace orsharpen Anti - Kickback Pawls when points become dull . extend across the full length of the Miter Gauge face during the cut . This lets you properly hold the Miter 3 . Plastic and composition ( like hardboard ) materials Gauge and workpiece and helps keep your hands may be cut on your saw . However , since these are away from the blade . usually quite hard and slippery , the Anti - Kickback WHILE CUTTING Pawls may notstop a kickback . Therefore , be espe - cially careful in your set - up and cutting procedures . 1 . To avoid blade contact , always hold the Miter Gauge as shown in the " BASIC SAW OPERATIONS - US - WHILE CUTTING ING THE MITER GAUGE . " 1 . To avoid kickbacks and slips into the blade , always BEFORE LEAVING THE SAW pushforward onthe section of the workpiece between 1 . Turn the saw off . the saw blade and the Rip Fence . Neverpushforward on the piece being cut off . . Wait for blade to stop spinning . ADDITIONAL iNSTRUCTiONS FOR 3 . Make workshop child - proof . Lock the shop . Discon - CROSSCUT TYPE CUTS nect master switches . Remove the yellow Switch Key . Store it away from children and others not BEFORE STARTING qualified to use the tool . 1 . NEVER use the Rip Fence when crosscutting . 4 . Unplug the saw . glossary of terms for woodworking KIckback Anti - Kickback Pawls ( AKP ) Device which , when properly maintained , is designed to Anuncontrolled grabbing and throwing of the workpiece back toward the front of the saw . stopthe workpiece from being kicked back at the opera - tor during ripping operation . Leading End Arbor The end of the workpiece which , during a rip type The shaft on which a cutting tool is mounted . operation , is pushed into the cutting tool first . Crosscut Molding A cuttingor shaping operation made across the width of A non through cutwhich produces a special shape inthe the workpiece . workpiece used for joining or decoration . Dado Push Stick A non through cut which produces a square sided notch A device used to feed the workpiece through the saw or trough inthe workpiece . during narrow ripping type operations and helps keep the operator's hands well away from the blade . Featherboard A device which can help guide workpieces during rip Push Block type operation . A device used for ripping type operations too narrow to allow use of a Push Stick . Freehand Performing a cut without using a Fence , Miter Gauge , Rabbet fixture , hold down or other proper device to keep the A notch in the edge of a workpiece . workpiece from twisting during the cut . Resin Gum A sticky , sap base substance that has hardened . A sticky , sap based residue from wood products . Ripping Heel A cutting operation along the length of the workpiece , Misalignment of the blade . Revolutions Per Minute ( RPM ) Kerr The number of turns completed by a spinning object in The amount of material removed by the blade in a one minute . throughcut or the slot produced by the blade in a non through or partial cut .
Page: 6

glossary of terms for woodworking Thru - Sawing Sawbisde Path Any cutting operation where the blade extends com - The area ofthe workpiece ortable topdirectly inline with pletely through the thickness of the workpiece . the part of the workpiece whichwill be , or has been , cut by the blade . Trailing End The workplace end last cut by the blade in a ripping Set operation . Thedistance that thetip of the sawblade tooth isbent ( or set ) outward from the face of the blade . Workploce The item on which the cutting operation is being done . Throw - Back The surfaces of a workplece are commonly referred to Throwing of pieces in a manner similar to a kickback . as faces , ends and edges . ii motor specifications and eiectrica ! requirements Thissawisdesignadtouse a3450RPM motoronly . Do WARNING : Failure to properly ground this power tool can cause electrocution or serious shock , not use any motor that runs faster than 3450 RPM . It is wired for operation on 120 volts , 60 Hz . , alternating partlcuisrly when used In damp locations , or near current . IT MUST NOT BE CONVERTED TO OPER - meta ! plumbing . If shocked , your reaction could ATE ON 230 VOLTS . cause your hands to hit the cutting tool . WARNING : Do not use blower or washing This saw is equipped with a 3 - conductor cord and chine motors or any motor with an automatic grounding type plug which has a grounding prong , reset overload protector . They can start up by approved by Underwriters ' Laboratories and the Cana - dian StandardsAssociation . The ground conductor has themselves and you could get Injured . a green lugand is attachedto the tool housing atone end CONNECTING TO POWER SOURCE and to the ground prong in the attachment plug at the OUTLET other end . This saw must be grounded while in use to protect the This plug requires a mating 3 - conductor grounding type operator from electrical shock . outlet as shown . It is recommended that you have a qualified electrician shock or fires . If the power cord is worn , cut or replace the TWO prong outlet witha properly grounded damaged In any way , have It replaced immedF THREE prong outlet . JWARNING : Damaged power cords can cause stely . GROUNDING LUG Your saw is wired for 120 volts and has a plugthat looks / _ - - like the one shown below . J J " _ , ' ! I MAKESURETHISIS 3 - PRONG _ ' _ _ _ , _ . - . _ - - CONNECTED TO A ADAPTER Atemporary adapter , as shown , isavailable forconnect - \ ing plugs to 2 - prong receptacles . The green grounding GROUNDING PRONG / fl g / lug extending from the adapter must be connected to a PROPERLY GROUNDED permanent ground suchas to a properlygrounded outlet 3 - PRONG OUTLET box . This adapter should be used only until a properly grounded outlet can be installed by a qualified electri - Plug power cord of fully assembled saw into a 120V cian . properly grounded type outlet protected by a 15 amp . WARNING : Avold electric shock , lftheoutlet you time delay or Circuit - Saver fuse or circuit breaker . are planning to use for this saw is of the two prong type , DO NOT REMOVE OR ALTER THE GROUND - ING PRONG IN ANY MANNER . Use an adapter , as your outlet Is properly g rounded , have It checked shown , and always connect the grounding lug to by a qualified electrician . a known ground , such as to a properly grounded outlet box . Not all outlet boxes are properly WARNING : To avoid electrical ShOCk , do not grounded , ff you are not sure the outlet box Is permit fingers to touch the terminals of the plug , properly grounded , have It checked by a qua llfled when Installing or removing the plug to or from eisctrlclan . the outlet .
Page: 7

NOTE : Theadapterillustratedis for use only if you 1 H . P . MOTR 110 - 120V already have a properly grounded 2 - prong receptacle . Extension Cord The use of any extension cord will cause some loss of Length Wire Size A . W . G . power . To keep this to a minimum and to prevent 0 - 25 Feet No . 16 overheating and motor burn - out , use the followingtable 26 - 50 Feet No . 14 to determine the minimum wire size ( A . W . G . ) extension 51 - 100 Feet No . 12 cord . CHECK MOTOR ROTATION Use only 3 wire extension cords which have 3 - prong grounding type plugs and 3 - prong receptacles which The motor must rotate CLOCKWISE when viewed from accept the plug on the saw . the shaft end to which you will mount the pulley . ( See page 21 . ) If it does not , do not assemble or use saw until motor with right rotation is installed . contents Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Rip Fence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Safety instructions for Table Saw . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Miter Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Additional Instructions for Rip Type Cuts . . . . . . . . . . . . . . . 4 Blade Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Additional Instructions for Cross Cut Type Cuts . . . . 5 Table Insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Removing and Installing Sawblade . . . . . . . . . . . . . . . . . . . . . . 27 Motor Specifications and Exact - I - Cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Safety Instructions for Basic Saw Operation . . . . . . 28 Connecting to Power Source Outlet . . . . . . . . . . . . . . . . . . . . . . 6 Basic Saw Operation - Using the Miter Gauge . . . . 30 Motor Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Work Helpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Unpacking and Checking Contents . . . . . . . . . . . . . . . . . . . . . . . . 8 Crosscutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Tools Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Repetitive Cutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 List of Loose Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Miter Cutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Bevel Crosscutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Installing Handwheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Compound Miter Cutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Checking Table Insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Using the Rip Fence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Checking Blade Squareness to Table . . . . . . . . . . . . . . . . . 10 Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Assembling Steel Legs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Bevel Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Mounting Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Using Featherboards for Thru - Sawing . . . . . . . . . . . . . . . . . 36 Attaching and Assembling Table Extensions . . . . . . . 12 Resawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Mounting Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Cutting Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Installing Right Front Rip Fence Guide Bar . . . . . . . . . 14 Rabbeting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Installing Rear Fence Guide Bar . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Ploughing and Molding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Aligning Rip Fence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Dadoing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Self Aligning Spring Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Molding Cutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Rip Fence Lock Lever Adjustment . . . . . . . . . . . . . . . . . . . . . . . 18 Using Featherboards for Non Thru - Sawing . . . . . . . . . 38 Rip Fence Alignment Adjustment . . . . . . . . . . . . . . . . . . . . . . . . 18 Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Adjusting Rip Scale Pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Miter Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Installing Blade Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Heeling Adjustment or Parallelism of Sawblade Mounting the Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 to Miter Gauge Groove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Installing Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Blade Tilt , or Squareness of Blade to Table . . . . . . . . 41 Installing Belt Guard Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Tilt Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Installing Belt Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Plugging in Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Lubrication . . . . : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Getting to Know Your Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Recommended Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 On - Off Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Elevation Handwheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Tilt Handwheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Tilt Lock Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Page: 8

unpacking and checking contents TOOLS NEEDED COMBINATION SQUARE MUST BE TRUE , Phillips Screwdriver STRAIGHT EDGE OF BOARD 3 , 4 " THICK . THIS EOGE MUST BE PERFECTLY STRAIGHT . Medium Scra _ dr | ver DRAW LIGHT LINE ON _ Small Screwdriver BOARD ALONG THIS EDGE ; ' _ _ / Plier SIZE Combination Square L _ / Set Screw Wrenches 3 / 32 In . SHOULD BE NO GAP OR OVERLAP HERE WHEN SQUARE IS FLIPPEO 1 / 8 In . Wrenchea OVER IN OOTTED POSITION . 5 / 32 In . 7 / 16 in , 1 / 2 in . 91 " 16 In . r Separate all parts from packing materials and check ITEM PART NAME QTY . each one with the illustrationand the listof Loose Parts A tO make certain all items are accounted for , before Blade Guard and Spreader . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 B discarding any packing material . Rip Fence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 C Owner's Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 D Cast Iron Table Extensions . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 tempt to assemble the table saw , plug in the E Miter Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 power cord or turn the switch on until the missing I WARNING : ff any parts are missing , do not at - H Rip Fence Guide Bar with Rip Scale ( Front ] . 1 parts are obtained and are in _ alle , ( : l correctly . M Support , Motor Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Remove the protective oil that is applied to the table top Q Rip Fence Guide Bar ( Rear ) . . . . . . . . . . . . . . . . . . . . . . . . . 1 andedges of the table . Use any ordinaryhouseholdtype R Side Stiffener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 S grease and spot remover . Leg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 T End Stiffener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 U Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 use gasoline , naptha , or similar highly volatile WARNING : To avoid fire or health hazard , never ] Bag of Loose Parts solvents . i ( Containing the following items ) Apply a coat of automobile wax to the table . G Outlet , On / Off with Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 J Handwheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Wipe all parts thoroughly with a clean , dry cloth , AM Bracket , " L " Mounting ( Model 113.298721 ) . . . 1 Bag of Loose Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 plug to power source outlet until all assembly Bag of Loose Parts stepsarecomplete , aad you have mad and under - WARNING : For your own safety , never con _ ! ( Containing the following items ) ! stand the safety and operating Instructions . F Wrench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 K Belt , " V " 1 / 2 x 41 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 L Pulley , 112dia . with 5 / 8 Bore . . . . . . . . . . . . . . . . . . . . . . . . . 1 N Spreader , Rod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 O Blade Guard Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 P Spreader Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 il / . . . . . . . . . . 14 £ @ ( MODEL 11 _ L29B762 ) H J u ( MODEL 113.298722 i 8
Page: 9

ITEM PARTNAME QTY BagofLoosePartsNo . ( Containintghefollowingitems ) V BeltandPulleyGuard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . . W BeltGuardClip " S " . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 X Screw , Pan Hd . 10 - 32 × 1 / 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Y Support , Belt Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Z Belt Guard Support Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Bag of Loose Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Bag of Loose Parts ( Containing the following items ) X Screw , Pan Hd . 10 - 32 × 3 / 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AA Screw , Hex Hd . 1 / 4 - 20 × 5 / 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AA Screw , Hex Hd . 5 / 16 - 18 x 5 / 8 . . . . . . . . . . . . . . . . . . . . . . . . . . 3 AA Screw , Hex Hd . 5 / 16 - 18 x 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 AA Screw , Hex Hd . 5 / 16 - 18 x 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 AA Screw , Hex Hd . 5 / 16 - I8 x 1 - 1 / 4 . . . . . . . . . . . . . . . . . . . . . . . 1 AA Screw , Hex Hd . 5 / 16 - 18 x 1 - 3 / 4 . . . . . . . . . . . . . . . . . . . . . . . 2 AB Nut , Hex 1 / 4 - 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AB Nut , Hex Jam 5 / 16 - 18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 AC Lockwasher , External # 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AC Lockwasher , External 1 / 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AC Lockwasher , External 5 / 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 AD Carriage Bolt , 5 / 16 - 18 × 3 / 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 AE . . Screw , Thumb 5 / 16 - 18 × 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 AF Washer , 21 / 64 x 5 / 18 x 1 / 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 AL Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AG AH A | AF Bag of Loose Parts ( Containing the following items ) AA Screw , Hex Hd . 5 / 16 - 18 x 1 - 1 / 4 . . . . . . . . . . . . . . . . . . . . . . . 4 AB Nut , Hex 1 / 4 - 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 AB Nut , Hex Jam 5 / 16 - 18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 AB Nut , Hex Jam 3 / 8 - 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 AC Lockwasher , External 1 / 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 AL AC Lockwasher , External 5 / 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 AK AF Washer , 11 / 32 x 11 / 16 x 1 / 16 . . . . . . . . . . . . . . . . . . . . . . . . . . 8 AG Screw , Truss Hd . 1 / 4 - 20 x 1 / 2 . . . . . . . . . . . . . . . . . . . . . . . . 24 AH Foot , Leveling 3 / 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Bag of Loose Parts ( Containing the following items ) AA Screw , He × Hd . 5 / 16 - 18 x 1 - 1 / 4 . . . . . . . . . . . . . . . . . . . . . . 8 AB Nut , Heavy Hex Jam 5 / 16 - 18 . . . . . . . . . . . . . . . . . . . . . . . . . . 8 AC Lockwasher , External 5 / 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 AF Washer , 11 / 32 x 11 / 16 x 1 / 16 . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Bag of Loose Parts ( Containing the following items ) AJ Spacer , Rip Fence Guide Bar . . . . . . . . . . . . . . . . . . . . . . . . . . 3 AK Tie , Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Page: 10

assembly Before mountingthe saw on legs , a standor a bench , the Table Insert and Blade Squareness must be checked at tt _ s time . LOCKWASHER INSTALUNG HANDWHEELS 1 . Line up FLAT SPOTS on shaft and Handwheel , Push Handwheelonto shaft . Install screw and Iockwasher 10 - 32 X 314 IN . to lock Handwheel on shaft . / PHILLIPS HEAD SCREW ELEVATION TIL'F HANDWHEEL HANDWHEEL CHECKING TABLE INSERT make sure switch Is " OFF " and plug is not con - i WARNING : To avoid Injury lrom accidental _ rt , nected to power source outlet . 1 . Insert should beflushwithtabletop , Chsck as shown . Loosen flat head screw that holds inert and adjust the four set screws as necessary . Tighten flat head screw . Do not tighten screw to the point where it deflects the insert . CAUTION : Insert must be even with the table surface , inserts too high or low can let the workplece " snag " or catch on uneven edges . Workplece could twist and kick back . i1 2 . To remove Insert A . Make sure saw is off and unplugged . B . Loosen Screw . C . Lift Insert from front end , and pull toward front of saw . 3 . To replace Insert . A . Make sure saw is off and unplugged . B . Place insert into insert opening in table and push toward rear of saw to engage springclip and until keyslot in Insert will drop over screw . Tigl'ten screw . C . Do not tighten screw to the point where it will deflect the Insert . CHECKING BLADE SQUARENESS TO TABLE IMPORTANT : BLADE must be SQUARE ( 90o ) " ¢ _ TABLE , in order to proceed with assembly . MAKE SURE SQUARE IS NOT TOUCHING 1 . Make sure saw is off and unplugged . TIP OF TOOTH / 2 . TurnElevation Handwheel clockwise until blade is up / / as highas it will go . 3 . Check for BLADE SQUARENESS . ff blade is not square to table , adjust it at thistime . NOTE : The combination square must be " true " - see start of * Unpacking and Checking Contents " section on page 6 for checking method . Refer to " Blade Tilt , or Squareness of Blade to Table " adjustment on page 39 . 10
Page: 11

© G ASSEMBLRNG STEEL LEGS 114IN EXTERNAL 1 / 4 - 20 1 . From among the loose parts , find the following hard - LOCKWASHER HEX NUT ware : 114 - 20 x 1 / 2 IN . * 24 Truss Head Screws , 1 / 4 - 20 x 1 / 2 " long TRUSS HEAD SCREW * 24 Lockwasher , 1t4 External * 24 Hex Nuts , 1 / 4 - 20 * 8 Hex Nuts , 3 / 8 - 16 * 4 Leveling Feet Items marked with an asterik ( * ) are shown actual size . 318 - 16 HEX NUT LEVELING FOOT 2 . Assemble the legs as shown . insert the Truss Head Screws through the holes in the legs , then through the holes in the Stiffeners . MAKE ASSEMBLE SCREWS SURE THE SCREWS GO THROUGH THE HOLES THROUGH HOLES IN THE SIDE STIFFENERS MARKED " X " . MARKED " X " 3 . Install the Iockwasher , screw on the nuts but do not SIDE STIFFENER tighten until completely assembled . 4 . Install Leveling Feet . END STIFFENER IN . HEX NUTS MOUNTING SAW 1 . From among the loose parts , find the following hard - ware : * 4 Hex Head Screws , 5 / 16 - 18 x 1ol14 " ! ong HEX HEAD SCREW 5tt6 - 18 * 4 Hex Nuts , 5t16 - 18 HEX NUT * 4 Lockwasher , 5 / 16 External Type * 8 Flat Washers , 11 / 32x 11 / 16 x 1 / 16 Items marked with an astedsk ( * ) are strewn actual size . WARNING : The saw Is heavy . To avoid back Q Injury , get help to lift the saw . Hold the saw close to your body . Bend your knees so you can liftwith t 5116 IN EXTERNAL FLAT WASHER your legs , not your back . LOCKWASHER ! 1
Page: 12

assembly SAW . _ IBASE t 2 . Place saw on legs so that holes in bottom of saw line HEX HEAD SCREW " ' - - _ l up with holes in top of legs . 3 . Install screws , washers , Iockwashers and nuts as FLAT WASHER _ _ shown . END _ . STIFFENER - _ i _ _ , " 1 LOCKWASHER " " _ ' ' ' / / / 7 / 16 DIA . HOLES / If you mount the saw on any other bench , make sure that F @ there is an opening in the top of the bench the same size 7 - as the opening in the bottom of the saw so that the sawdust can drop through _ Recommended working height is 33 to 37 inches fromthetopof the saw table to the floor . 13 16 / I , I , / " \ \ _ _ \ ® FRONT OF SAW - - ' _ 1 / 2 2 - 3 / 4 NOTE : All dimensions in inches ATTACHING AND ASSEMBLING TABLE EXTENSIONS @ 1 . Fromamongthe loose parts findthe following hard - ware : ( Quantity indicated isfor two extensions ) HEX HEAD SCREW 5t16 - 18 HEX NUT * 8 Hex Hd . Screw 5 / 16 - 18 x 1 - 1 / 4 * 8 Flat Washer * 8 External Lockwasher , 5 / 16 " 8 Hex Nut , 5t16 - 18 Items marked with an asterik ( * ) are shown actual size . O 5 / 16 IN EXTERNAL FLAT WASHER LOCKWASH ER 12
Page: 13

2 . Insert four ( 4 ) 5 / 16 - 18xl 114 in . long screws through hole in each Extension . 3 . Position extension against table so screws extend through hole in table . 4 . Install flat washers , Iockwashers , and nuts on the screws . . . DO NOT TIGHTEN . ! 5 . Line up the rear edge of extension with the rear edge of the table and top surface of the extension with the top of the table at the spots marked " X " in the drawing . Use a combination square to line - up these edges . SLIGHTLY TIGHTEN nuts with a 1 / 2 " wrench . CHECK WITH SQUARE AT 2 PLACESiTH MARKED W " X " 6 . If the side extension is lower in the center than each end , loosen the center two screws . Using a " C " clamp " C " CLAMP ( not provided ) , raise the side of the extension until it is even with the table surface as shown . Firmly tighten nuts . 7 . Repeat steps 2 thru 6 to install the other extension . I I MOUNTING SWITCH 1 . From among loose parts findthe following : * 2 Hex Head Screw 5 / 16 - 18 x 3 / 4 5116 - 18x 3 / 4 * 2 Flat washers . 21 / 64 x 5 / 8 x 1 / 16 HEX HEAD SCREW 21164 IN WASHER * 2 External Lockwashers , 5 / 16 * 2 Hex Nuts , 5 / 16 - 18 HE ) ( NUT LOCK WASHER 5 / 16 iN 5 / 16 IN EXTERNAL Items marked with an asterisk ( * ) are shown actual size . 13
Page: 14

JAM NUT 5 / 16 - 18 assembly 1 LOCKWASHER 2 . Position front guide bar upside down as illustrated . _ / " 7 5TH HOLE 3 . Insert two 3 / 4 inch screws through two flat washers then through holes in switch . J _ ' \ _ FRONT FENCE 4 . Insert screws through holesfive and six infrontfence 6TH HOLE ' , - \ _ . _ _ - _ GUIDE BAR ( UPSIDE DOWN ) guide bar as illustrated . % % " _ " " - W ASH E R 5 . Install two Iockwasher and nuts . Tighten nuts . HEX HEAD SCREW 5 / 16 - 18 x 3 / 4 IN . iNSTALLiNG RIGHT FRONT RIP FENCE GUIDE BAR 5 / 16 - 18 x 1 - t / 4 IN 1 . From among the loose parts , find the following hard - 5 / 16 IN HEX HEAD SCREW 5 / 16 IN EXTERNAL ware : HEX NUT LOCK WASHER * 2 Hex Head Screws , 5 / 16 - 18x 1 - 3 / 4 " 1 Hex Head Screws , 5 / 16 - 18x 3 / 4 * 4 Lockwashers , 5 / 16 External Type * 4 Hex Nuts 5 / 16 - 18 HEX HD . SCREW 5 / 16 - 18 x 3 / 4 IN " 3 Spacers , 3 / 4 diameterx 1 / 2 long " 1 Hex Head Screw 5 / 16 - 18 x 1 - 1 / 4 * 2 Flat Washers 5 / 8 x 1 / 16 1 Bracket HEX HEAD SCREW Items marked with an asterik ( * ) are shown actual size . 5 / 8 x 1 / 16 IN WASHER 314IN . DIA . X 112IN . SPACER = BRACKET 2 . Put the bracket against the right edge of the right " _ - - - - - " - - _ extension so the bracket is lined up with the FIRST hole near the front of the extension . Insert a 3 / 4 long screw through a flat washer , through top hole in the bracket , and throughthe FIRST hole inthe extension . Installa lockwasherand nuton thescrew , Tightenthe T _ , , _ _ , _ / _ _ 1WASHER nut only slightly . EXTERNAL LOCKWASHER HEX HEAD SCREW 5 / 16 - 18 x 3 / 4 IN NOTE : The various holes in the Bar allow them to be positioned on the saw and also makes them adapt - able to other models . t 3 . Insert a 1 - 314 inch long screw through the second hole from LEFT Inthe Front Bar . _ ' CENTER HOLE : ' \ IN TABLE 2ND HOLE IN BAR 5 . Turn front bar perpendicular and insert bolt through ; P center hole in middleof saw table as illustrated . Install lockwasher and nut . DON'T SCREW NUT ON ALL THE ' NAY , just get the nut started on the screw . _ f 6 . Rotate guide bar parallel to table . 14
Page: 15

4TH HOLE IN BAR 7 . Insert 1 - 1 / 4 inch long screw through slot in bar that NUT HEX HEAD SCREW matches hole in bracket . Install spacer , Iockwasher 5 / 16 - 8 X 1 - 3 / 4 IN . and nut . DON'T SCREW NUT ON ALL THE WAY , just get the nut started on the screw . 8 . Install spacer between guide bar and the last front table hole which aligns with the fourth hole inthe front scREW guide bar . 5 / 16 - 8 X 1 - 3 / 4 IN . 9 . Insert 1 - 3 / 4 inch long screw through the hole in bar , LOCKWASHER spacer and hole intable . Install Iockwasher and nut but do not tighten . iNSTALLiNG REAR FENCE GUIDE BAR 1 . From among the loose parts find the following : 5 / 16 - 18 x ! IN 5 / 16 - 18 x 3 / 4 1 Bracket HEX HD . SCREW HEx HEAD FLATWASHER * 2 Hex Head Screws 5 / 16 - 18 x 1 * 2 Hex Head Screws 5 / 16 - 18 x 3 / 4 * 4 Flat Washers 5 / 8 x 1 / 16 * 4 External Lockwashers 5 / 16 * 4 Hex Nuts , 5 / 16 - 18 1 Rear Fence Guide Bar 5 / 16 IN EXTERNAL 5 / 16 - N18UT Items marked with an astedk ( * ) are shown actual size . LOCKWASHER HEX REAR FENCE GUIDE BAR BRACKET REAR OF 2 . Put the bracket against the right rear edge of the right extension so the bracket is lined up with the FOURTH EXTENSION _ 4TH HOLE hole near the rear of the extension ( see illustration ) . 3 . Insert one of the 3 / 4 inch long screws through a flat washer , through the bracket , and through the FOURTH _ \ _ / _ WASHER hole in the extension . Install a Iockwasher and nut on the screw . Tighten the nut only slightly . LOCKWASHER 5 / 16 - 18 x 3 / 4 HEX HEAD SCREW 4 . Insert a 1 inch long screw through a flat washer and through the fourth hole of the rear fence guide bar . Turn rear bar perpendicular to table and insertscrew through the middle hole as illustrated . Install LOCKWASH _ UT _ , : OC \ KWA _ Iockwasher and nut loose to adjust guide bar to the horizontal position . 11TH HOLE _ , . , I - _ . _ " - 7 _ ' ' ' _ - _ - - - - - - _ - Vj - _ T - _ - 5 . Insert a 3 / 4 inchlong screwthrough a flat washer , bar , and bracket . Install Iockwasher and nut but do not tighten . HEX HEAD SCREW WASHER i HEX HEAD SCREW 6 . Insert 1 inch long screw through a flat washer and 5 / 16 - 18 X 3 / 4 HEX HEAD SCREW 5 / 16 - 18 X 1 5 / 16 - 18 X 1 IN . through the second hole of the rear fence guide bar plus through the matching hole in table . Install Iockwasher and nut loosely . 15
Page: 16

assembly 7 . Position Rip Fence over Miter Gauge Groove , holding up the rear end while engaging front end with Bar . Lower Fence onto table . 8THICKNESSES 8 . Raise blade all the way up , OF PAPER 9 . Carefully move Fence against blade . t0 , Move Front Bar until " 0 " mark on Rip Scale is approximately in line withtip of Pointer . 11 . Move Front Bar upwards until Fence is approxi - mately 1 / 32 inch above table , Tighten screw at left end of Bar . NOTE : Fold a piece of newspaper making 8 thick - nesses and place between Rip Fence and table to o act as a spacer . This will hold the Fence off of the table approximately 1 / 32 inch . 12 . Adjust Rear Barso thal the Fence is approximately 1132 inch above table , make sure it is square with MiterGauge Groove . Tighten screw atend of Bar . 8 THICKNESSES OF PAPER 13 . Move Fence to RIGHT edge of table . Make sure it is approximately 1 / 32 inch above table at front and rear and tighten screws . t6
Page: 17

ALIGNING RiP FENCE The Fence should slide easily alongthe Bars and always remain in alignment ( parallel to sawblade and Miter Gauge Grooves ) , The alignment is maintained by a spring underneath the Fence which bears against the Front Guide Bar . To move the Fence , loosen the Lock Handle and grasp the Fence with one hand at the front . For very close adjustments , grasp the Guide Bar with both hands and move the Fence with your thumbs . \ SELF ALIGNING SPRING ADJUSTMENT Place Fence on saw but DO NOT LOCK IT . Move the REAR END of the Fence slightlyto the rightor left . When yourelease it , the Fence should " spring " back to its original position . if itdoes not , the spring pressure must be INCREASED , 1 . Loosen the screws . 2 . Move spring slightly toward front of Fence . Tighten screws . backs and jams . To avoid injury , follow these instructions until the fence properly self aligns . 17
Page: 18

assembly If the Fence does not slide easily along the Bars , the pressure of the spring can be REDUCED . 1 . Loosen the screws . 2 . Move spring slightly toward rear of Fence . Tighten screws . WARNING : To avoid Injury from jams or kick - SPRING backs , be sure to push properly adjusted Lock Lever all the way down untllthe laver rests onthe stop before using the Rip Fence . SLIDE SPRING TO ADJUST PRESSURE RiP FENCE LOCK LEVER ADJUSTMENT The Rip Fence Lock Lever , when locked down , should holdthe Rip Fence securely , it should not be difficultto push down and lock . If LOCkLever does not Iockfence securely : 1 . Raise Lock Lever . 2 . Tighten the adjusting nut using a small screwdriver until the lever , when locked , holds the Rip Fence securely . If Lock Lever is difficultto push down : 1 . Raise Lock Lever . 2 . Loosen the adjusting nutusing a small screwdriver untilthe lever is easy to push down and holdsthe Rip Fence securely . RIP FENCE ALIGNMENT ADJUSTMENT 1 . The Rip Fence must be PARALLEL with the HEX SCREWS sawblade and Miter Gauge Grooves . Move Fence untilit is along side of Groove . DO NOT LOCK IT . It FENCE HEAD should be parallel to Groove . If it is not ; / A . Loosen the two Hex Hal . Screws . B . Hold Fenceheadtightlyagainst Bar . Move end of Fence sothat it is parallel with Groove . C . Altemately tighten the screws . D _ Recheck alignment . E . Repeat steps as needed . backs and jams . To avoid Injury , follow these \ i ARNING : A misaligned fence can cause kick - I Instructions until the fence is properly aligned . 18
Page: 19

ADJUSTmNG RiP SCALE POINTER 1 . Turn Elevation Handwheel clockwise untilblade is up as high as it will go . LOCK HANDLE F IMPORTANT : BLADE must be SQUARE ( 90 ° ) to TABLE , in order to ALIGN Rip Scale . 2 . Position Fence on right side of sawblade so that it touches the sides of the teeth , tighten Lock Handle . 3 . Loosen screw holding the Pointer , adjust so that it points to " 0 " on the Rip Scale , tighten screw . NOTE : Ityou cannot adjust Pointer so that it points to \ " 0 " , loosen the screws holding the Front Guide Bar \ \ and move the Guide Bar . \ \ INSTALLING BLADE GUARD 1 . From among the loose parts , find : © " 2 Hex Head Screws , 1 / 4 - 20 x 5 / 8 1 / 4 - 20 1 / 4 IN . * 3 Hex Head Screws , 5 / 16 - 18 x 5 / 8 HEX NUT EXTERNAL * 2 Hex Head Screws , 5 / 16 - 18 x 1 LOCKWASHER * 2 Hex Nuts , 1 / 4 - 20 k - - J _ ' _ " 2 Lockwashers , 1 / 4 External Type * 2 Lockwashers , 5 / 16 External Type " 1 Thumbscrew 1 Blade Guard Support 5 / 16 IN . 1 Spreader Support EXTERNAL BLADE GUARD 1 Spreader Rod LOCKWASHER THUMBSCREW SUPPPORT Items marked with an asterik ( * ) are shown actual size . LI 1 / 4 - 20 X 5 / 8 IN . SPREADER ROD 5 / 16 - 18 X5 / 8 IN . 5 / 16 - 18 X 1 IN . HEX HD . SCREW SPREADER SUPPORT HEX HD . SCREW HEX HD . SCREW 2 . Before installingthe BladeGuard , you mustcheckthe heeling adjustment ( parallelism of sawblade to Miter Gauge Groove ) . The procedurefor makingthischeck and adjusting it are found in the " ADJUSTMENTS " section of this manual . Refer to " Heeling Adjustment or Parallelism ofSaw Blade to Miter Gauge Groove . " WARNING : The blade must be parallel to Miter Gauge Groove . Mlsaligned blades could bind on workplace . Workplace could suddenly kick back . You could be cut or hit . 3 . Lower the blade . 4 . Screw the Motor Base Clamp Screws part way into cradle . Screw the 5 / 16 - 18 x 5 / 8 inch Hex Hd . screw intothe Blade Guard support . 5 . Attach Blade Guard Support . DO NOT TIGHTEN SCREWS . 19
Page: 20

assembly TH LIMB SCREW \ SPREADER _ 6 . Insert Spreader Rod into Spreader Support untilpin ROD fits into notch . Insert Thumbscrew and tighten it . \ \ FLAT SURFACE SPREADER SUPPORT ( INTO SUPPORT ) II 7 . Slide Spreader Rod into Blade Guard Support until end of Rod is even with edge of Support , Tighten Hex Head Screw in Support . 8 . Attach Spreader to Spreader Support so that the edge of the Spreader is ever _ with the edge of the Spreader Support . Tighten screws . 9 . Raise Anti - Kickback Pawls ( hold in place with a set - screwwrench - see below ) . AlignSpreaderSQUARE to table . 1 / 4 - 20 HE ] ( Tighten both 5 / 16 - 18 x I inch Hex Head Screws . HD . SCREW 1 / 4 IN . LOCKWASHER 1 ! 4 - 20 HEX NUT EVEN WITH SPREADER SUPPORT EDGE END OF ROD EVEN WITH EDGE OF SUPPORT J 5 / 16 - 18 X 1 IN . HEX HD . SCREWS 10 . Raise blade all the way up , make sure it is square with table . 11 . Raise Blade Guard . Lift up both Anti - Kickback Pawls . Insert one of the Setscrew Wrenches in the notches to hold the Pawls out of the way . 12 . Lay blade of square or other straightedge alongside of blade . 13 . Loosen Hex Head Screw in Guard Support and move Spreader so that it touches blade of square . Tighten screw . and approximately in line with the sawblade . The Spreader requires further adjustment to alignit PAR - ALLEL to the blade and in the MIDDLE of the cut SCREW ( KERF ) made by the sawblade .
Page: 21

KERF WOOD 15 . iMPORTANT : To work properly , the Spreader must always be adjusted so the cut workplece will pass on either side at the Spreader without binding or skewing to the side . NOTE : The Spreader isthinner than the width of the / cut ( KERF ) by approximately six thicknesses of SPREADER paper . LOOKING DOWN ON SAW 16 . Make two folds in a small piece ( 6 x 6 inch ) of ordinary NEWSPAPER making three thicknesses . The folded paper will be used as a " spacing gauge " . 17 . Place Rip Fence on table . CAREFULLY move it against blade so that it is parallel to the blade , and just TOUCHES tips of saw teeth . Tighten Rip Fence l FOLDED PAPER Lock Lever . 18 . Insert folded paper between Spreader and Fence . 19 . Using 7 / 16 wrench loosen the 114 - 20 hex head screws so the Spreader can slide sideways . 20 . Hold Spreader flat against Fence . Tighten screws using 7 / 16 inch wrench . 7 / 16 IN . WRENCH 21 . To remove Blade Guard and Spreader , loosen Thumbscrew . DO NOT LOOSEN OTHER SCREWS . This lets you remove and replace the Guard without disturbing the Spreader alignment . MOUNTING THE MOTOR Model 113.298722 & 113.298762 KEY 1 . The Motor must rotate CLOCKWISE when viewed _ J from the 5 / 8 inch shaft . , - 2 , MAKE SURE " KEY ' IS REMOVED FROM SHAFT . 3 . Place the Motor on your workbench or on the floor . / _ Check Motor Rotation _ / / _ _ , _ / " MOTOR SPECIFICATIONS AND ELECTRICALee 4 . Plug the cord into a properly grounded outlet ( S _ 0TAI.jON REQUIREMENTS " section ) Notice the rotation of 5 / 8 IN . DIA . SHAFT the shaft . If it is not turning CLOCKWISE , do not assemble or attempt to operate saw untilmotor with correct rotation is obtained . 21
Page: 22

assembty 5 . From among the loose parts , find the following ONLY hardware : BELT GUARD BELT GUARD MOTOR * 4 Carriage Bolts , 5116 - 18 x 3 / 4 " L " BRACKET SUPPORT BRACKET PULLEY * 4 He × Nuts 5 / 16 - 18 ° 4 Lockwashers , 5t16 External Type 1 Motor Pulley 1 Belt Guard " L " Bracket G 1 Belt Guard Support Bracket 5 / 16 - 18 5 / 16 IN EXTERNAL items marked with an astedsk ( * ) are shown actual size . 5 / 16 - 18 x 3 / 4 IN CARRIAGE BOLT HEX NUT LOCKWASHER i POSITIONING MOTOR ON MOTOR MOUNTING LOOSEN BOTH CRADLE CLAMP SCREWS BASE Modet 113.298762 1 . Put the motor mounting base against theflat sudace o ! a workbench . 2 . Position the motor so the end with terminal cover is facing you . 3 . Loosen both cradle clamp screws . 4 . Put a square against the LEFT side of the motor and against the top of the workbench . 5 . Turn the motor inside the cradle clamps until the top of both capacitors touch the square . 6 . Tighten both cradle clamp screws to holdthe motor in ' _ MOTOR M2 # NTING this position . SQUARE _ _ HAS _ , - _ - _ + _ 1 " _ 1 o I WORKBENCH let workpleca strike capacitor cover during bevel or compound miter cuts . Workpleca could biml I WARNING : Failure to properly InStall motor may and kick back . You could be cUt or hit . WELDED MOTORSE MOUNTING BA MOUNTING MOTOR ON MOTOR BASE I THESE TWO CARRIAGE BOLT EDGES EVEN 5t16 - 18 X 3 / 4 IN . Model 113.298722 & 113.298762 LOCKWASHER 5 / 16 IN , 1 . Place Motoron Motor Base so that shaft is pointingto N " l " _ ' N _ , _ . J " 3 the right . Insert bolls through holes in Base , then u _ . _ . = _ _ 5 / 16 - 18 throughthe Motor Mounting Base . Install Iockwashe _ and nuts , DO NOT TIGHTEN AT THIS TIME . 2 . Position Motor so that edge of Motor Foot and Motor 3ASE Base are even . Slide Motor allthe way tothe RIGHT . Slip the long part of the " L " Bracket fully under the Motor so the short part is just undershaft ( Model 113 . 298722 only ) . Tighten the four nuts . BELT GUARD INSERTED EVEN WITH MOTOR END HUB away from Motor . DO NOT TIGHTEN SETSCREW . grooves inPulley and rnotorshaft . DO NOTTIGHTEN SETSCREW . 4 . Install3 / 16 inch square key ( furnished with Motor ) in 2 . Lowerthe blade , install Belton Saw Pulley and Motor INSTALLING BELT Pulley . Model 113.298722 & 113.298762 3 . Sight along edges of both pulleys and move Motor 1 . Lift Motor and insert the TWO PINS on Motor Base Pulley so that belt is parallel to the edges of both into HOLES in Cradle . Push Motor inas far as it will Pulleys . Tighten the set screw in the Motor Pulley . go . 22
Page: 23

4 . iMPORTANT : Measure the distance from end of Motor sha _ to Pulisy . Mark this dimension down ; you will need It later when reinstalling the Pulley . 5 . Make sure blade is90 ° totable , raise italltheway up . 6 . Lift Motoruntiledge of washer iseven with end of slot tighten pivot screw . Inthisposition , pullMotortoward EDGE OF WASHER you ( pins will slide out of Cradle ) untilBell is TIGHT , EVEN WITH END OF SLOT tighten the two Motor Base Clamp Screws . 7 . Loosen Pivot Screw slightly . 8 . Lower the saw blade all the way down . . MOTOR BASE CLAMP SCREWS _ 9 . IMPORTANT : Motor should pivot freely down - ward as blade Is lowered , if it does not , LOOSEN the Pivot Screw some more . 10 , Pivot Screw must be adjusted only tight enough to allow Motor to pivot FREELY as blade is raised and lowered . Thiswill maintain constant tension on Belt . SCREW / 11 . Put your hand around the belt halfway between the " L " BRACKET two Pulleys and squeeze Belt untiltwo sides of Belt MOTOR PULLEY touch . The Motorshould move freely as you squeeze the Belt . If Motor does not move freely , Belt tension must be readjusted . INSTALLING BELT GUARD Model 113.298722 1 . Remove the Belt and Motor Pulley . PIVOT 2 . Screws furnished with Guard are " SerfThreading " . SCREW Screw them intoholes inBeltGuard Support Bracket , then remove them . 3 , Position Belt Guard Support Bracketand Belt Guard Support as shown and installthe screws . Make sure Motor shaft is in CENTER of hole in Support . TWO HOLES CLOSEST BELT GUARD SUPPORT BELT GU / _ RO SUPPORT BRACKEt 10 - 32 X 1 tt IN * SELF - THREADING BELT GUARO SUPPORT SCREW INSTALLING BELT GUARD Model 113.298762 BELT GUARD 1 . Remove the Belt and Motor Pulley . 2 . Screws furnished with Guard are Self Threading . " PIVOT Screw them intoholes in BeltGuard Support Bracket , SCREW then remove them . 3 . Position Belt Guard Support Bracket and Belt Guard Support as shown and installthe screws . Make sure Motor Shaft is in CENTER of hole in support . " _ TWO HOLES CLOSEST TOGETHER / CENTERED BELTGUARD SUPPORT BRACKET 23 j BELT GUARD SUPPORT
Page: 24

OPENING / - assembly INSTALUNG BELT GUARD Model 113.298722 & 113.298762 BELT GUARD _ CLIPS 1 . Install three Clips ( furnished with Guard ) 90 ' apart starting wHh one Clip at the end of the Guard as shown . LONG END of Clip facing AWAY from you . \ LONG END BELT 2 . Reinstall Motor Pulley thesame way it was when you aligned the Belt . 3 . Place Belt on Saw Pulley . insert end of Belt through opening in END of Guard . 4 . Slip Belt over Motor Pulley . 5 . Press Guard onto Support sothat bottom of Guard is approximately 3 / 4 inch away from Belt . NOTE : To remove Guard , liftupon LONG TABS of Clips , pull Guard outward . The Clips should remain on the Belt guard Support . 3 / 4 iN . PLUGGING IN MOTOR 1 . From among the loose parts find : 2 Wire Ties wire ties . WIRE TIES EXTENSION REMOVED FOR PICTURE CLARITY 24
Page: 25

geeing to know your saw 9 SAWeLADE J 7 BLADE GUARD 8 TABLE INSERT 10 EXACT - I - CUT ANTIKICKBACK PAWLS 6 MITER GAUGE RIP FENCE HOLES FOR ATTACHING FACING RiP FENCE LOCK HANDLE ' 4 TILT LOCK HANDLE ( UNDERNEATH TABLE ) \ 2 ELEVATION HANDWHEEL 3 TILT HANDWHEEL \ ON - OFF SWITCH 1 ON - OFSFWITCH sure the blade guard is correc . y Installed and CAUTION : Beforetuming switch " ON " , make operating properly . The On - Off Switch has a locking feature . THIS FEATURE IS INTENDED TO PREVENT UN - AUTHORIZED AND POSSIBLE HAZARDOUS USE BY CHILDREN AND OTHERS . A . To turn saw ON , stand to either side of the blade , never in line with it , insert finger under switch KEY lever and pull END of lever out . ( YELLOW PLASTIC ) AfterturningswitchON , always allowthe blade to come up to full speed before cutting . Do not cycle the Motor Switchon and off rapidly , as this may cause the sawblade to loosen . Inthe event this should ever occur , allow the sawblade f _ _ y to come to a complete stop and retighten the arbor nut normally , notexcessively . Never leave the saw while the power in " ON " . B . To turn saw OFF , PUSH lever in . Never leave the saw untilthe cuttingtool has come to a complete stop . C . To lockswitchinOFF position , hold switchIN with one hand , REMOVE key with other hand . WARNING : Foryourown safety , lower blacis or other cutting tool below table surface . ( if blade is tilled , return R to vertloal , 90 ° , posF tlon . ) Always lock the s _ ltch " OFF " . When saw Is not In use , remove key and keep it in a e place . Also , in the event of is power lure ( all of your lights go out ) turn switch oft , lock It and rentove the key . Tide w ! lll prevent the saw from starting up again when the power comes back on . 25
Page: 26

If necessary , the Miter Gauge head can then be getting to know your saw swiveled slightly to compensate and then locked , 2 ELEVATION HANDWHEEL . . . elevatesor Slots are provided in the Miter Gauge for attaching Iowersthe blade . Turnclockwiseto elevate , counter - an Auxiliary Facing to make it easier to cut long clockwise to lower . pieces . Be positive Facing does not interfere with 3 TILTHANDWHEEL . . . tiltsthebladfeorbevel the proper operation of the Sawblade Guard . cutting . Tum clockwise to tilt toward left , counter - Select a suitablepiece of smooth straight wood , drill clockwise to tilt toward right . two holes through it and attach it with screws When the blade is tilted to the LEFT as far as itwill NOTE : When bevel crosscutting , attach Facing so go , it should be at 45 ° to the table and the bevel that it extendslo the rightof the Miter Gauge and use pointer should point 45 ° . the Miter Gauge in the groove to the right of the blade . NOTE : There are LIMIT STOPS inside the saw which prevent the blade from tilting beyond 45 ° to the LEFT and 90 ° to the RIGHT . ( See " ADJUST - MENTSAND ALIGNMENTS " section " BLADE TILT . OR SQUARENESS OF BLADE TO TABLE " ) . 4 TILT LOCK HANDLE . . . locks thebladeinthe desired tilt position . To loosen , turn counterclock - wise . Push handle in and turn it to another position _ ' _ Ry FACING if necessary in order to tighten or loosen . 5 RIP FENCE . . . isk _ ckedinplace bypushingthe STOP Pill 450 SLOT \ . I J LockLeverdownuntilthe lever rests onthestop . To FOR STOP PIN _ J _ _ _ move the Fence , lift the Lock Lever and grasp the Fence with one hand at the front . 7 BLADEGUARD . . . must always be in place and Holes are provided in the Rip Fence for attaching a working properlyfor all thru - sawing cuts . That is , all wood facing when usingthe Dado Head , or Molding Head . cuts where the blade cuts completely through the workpiece . Select a piece of smooth straight wood approxi - mately 3 / 4 inch thick , and the same size as the Rip To remove the Guard for special operations loosen Fence . the Thumbscrew and slidethe Guard off of the Rod . Attach it to the Fence with three Round Head # 10 DO NOT DISTURB THE SETTING OF THE ROD . Wood Screws , 2 inches long . To remove the facing , When replacing the Guard , make sure the PIN inthe loosen the screws , slide the facing forward and pull Rod engages with the NOTCH in the Spreader the screws through the round holes . Support . Make sure Thumbscrew is tightened se - WOOD FACING curely . 8 TAB LE iNSERT . . . is removable for removing or installing blades or other cutting tools \ \ • " \ / . / / _ ROUND HEAD . _ # 10 WOOD SCREWS . / 6 MITER GAUGE . . . headis Iockedinpositionfor SCREW cmsscuttingor mitering bytightening the Lock Knob . ALWAYS LOCK IT SECURELY WHEN IN USE . ! WARNING : TO avoid Inj _ from accidental start , turn switch " OFF ' and remove plug I po , , r NOTE : The slots forthe Stop Pin andthe gradu - A _ . Lowerthe blade below the table surface . ations are manufactured to very close tolerances B . Raise Biade GUard . which provide accuracy for average woodworking . C . Loosen screw . In some cases where extreme accuracy is required , D . Lift insert from front end , and pull toward front of when making angle cuts , for example , make a trial cut and then recheck it . saw . 26
Page: 27

NEVER OPERATE THE SAW WITHOUT THE BLADE GUARD NOT SHOWN PROPER iNSERT IN PLACE . USE THE SAW - FOR PICTURE CLARITY BLADE INSERT WHEN SAWING . USE THE COMBINATION DADO MOLDING INSERT WHEN USING A DADO OR MOLDING HEAD . 9 REMOVIHG AND INSTALLING SAWBLADE WARNING : To _ wv _ d injury from accldentaI start , _ m _ Rch " OFF " and remove plug _ om pawmr _ ouUst _ m removing or WOOD BLOCK Installing _ . A . Raise Blade Guard , remove Insert . C . To TIGHTEN arbor nut , place a block of wood B . To REMOVE Blade , place a block of wood against front of Blade , PULL arbor wrench toward you to against rear of Blade , PUSH wrench away from LOOSEN arbor nut . you . When installing the Blade , make sure the teeth are BLADE GUARD NOT SHOWN pointing toward the front of the saw and that the PICTURE CLARITY Blade and Collars are clean , and free from any burrs . The HOLLOW side of the collar must be against the Blade . Always tighten the arbor nut securely . NOTE : When using the Dado or Molding Head , it is not necessary to install the loose Collar . To replace insert . OR NUT Place insert into opening in table and push toward rear of saw to engage Spring Clip and until keyslot LOOSE in insert will drop over screw . Tighten screw . COLLAR ARBOR Do not tighten screw to the point where it will deflect the insert . ARBOR NUT WARNING : To avoid injury from a thrown workplece , blade parts , or b _ ade contact , TEETH POINTING TO - . . _ . . . . . _ - _ FRONT OF SAW , , % . _ . NEVER operate saw withou _ the proper insert In place . Use the sa _ ie Ir _ sert when = aw - ing . Use the proper size Dado / Moldlng for dado blades and molding heads . 10 EXACT - I - CUT The " yellow " Plastic Disc imbedded in the table in front of the sawblade , is provided for marking the location of the ' sawcut " on the workpiece . A . Check Disc . If it is above table surface , place a piece of hardwood on top of it and tap it down . BLADE GUARD NOT SHOWN B . With blade 90 ° ( square to table ) cross cut a piece FOR PICTURE CLARITY of wood . C . Pull Miter Gauge back until wood is over Disc . Using a sharp pencil , mark a line on Disc . D . With Miter Gauge in right hand groove , follow same procedure and mark another line on Disc . E . These lines indicate the " ' path " of the cut ( kerr ) made by the sawblade . F . When cutting the workpiece , line up mark on workpiece with line on Disc . 27
Page: 28

safety instructions for basic saw operations BEFORE EACH USE : 1 . inspect your saw 5 . Adjust table inserts flush with the table top . NEVER use the saw without the proper insert . A . To avoid injurytram accidental starting , unplugthe saw , turnthe switchoff andremove the Switch Key 6 . Makesure allclamps and locksare tight and no before raising or removing the Guard , changing parts have any excessive play . the cutting tool , changing the setup or adjusting 2 . Keep work area clean anything . A . Cluttered areas and benches invite accidents . B . Check for alignment of moving parts , binding of FlOormust not be slippery from wax or sawdust . moving parts , breakage of parts , mounting , and B . To avoid burnsor other fire damage , never use the any other conditions that may affect the way it saw near flammable liquids , vapors or gases . works , tfany part ismissing , bent , or broken inany C . To avoid injury , don't do layout , assembly , or setup way , or any electrical parts don't work properly , work on the table while the blade is spinning . It turn the saw off and unplug the saw . could cut or throw anything hitting the blade . C . Replace damaged , missing , or failed parts before AVOID ACCIDENTAL STARTING - Make sure using the saw again . switch is " OFF " before plugging saw in . D . Use the Sawblade Guard , Spreader , and Anti - Plan ahead to protect your eyes , hands , face , ears . Kickback Pawls forany thru - sawing ( wheneverthe 3 . Plan your work blade comes through the top of the workpiece ) . Makesurethe Pawlsworkpmperly . Makesurethe A . USE THE RIGHT TOOL - Don't force tool or Spreader is in line with the sawblade . attachment to do a job it was notdesigned for . E . REMOVE ADJ USTING KEYS AND WRENCHES . B . Dress for safety : Form habit of checking forand removing keys and 1 . Do not wearloose clothing , gloves , neckties or adjusting wrenches from tool before turning it on . jewelry ( rings , wristwatches ) . They can get F . To avoid injury from jams , slips or thrown pieces caught and draw you into moving parts . ( kickback and throwback ) : 2 . VVearnonslip footwear . 1 . USEONLY RECOMMENDEDACCESSORIES 3 . Tie back long hair . ( See page 40 ) . Follow the instructions that 4 . Roll long sleeves above the elbow . come with the accessories . Using other acces - Noise levels vary widely . To avoid possible sories may be dangerous . 5 . hearing damage , wear ear plugs or muffs when 2 . Choose the rightblade orcutting accessory for using saw for long periods of time . the material and the type of cutting you plan to Any power saw can throw foreign objects into do . 6 . the eyes . This can cause permanent eye dam - 3 . Never use grinding wheels , abrasive cut - off age . Wear safety goggles ( not glasses ) that wheels , friction wheels ( metal slitting blades ) . . . . . . . . ANSI Z87 . 1 ( shown on package ) . wire wheels or buflingwheel . They can fly apart Everyday eyeglasses have only impact resis - explosively . tant lenses . They are notsafety glasses . Safety 4 . Choose and inspect your cutting tool carefully . goggles are available at Sears retail catalog a . Toavoid cuttingtool failure andt hrownshrap - stores . Glasses or goggles not in compliance nel ( broken pieces of blade ) , use only 10 " or with ANSI Z87 . 1 could seriously hurt you when smaller blades or othercutting tools marked they break . for speeds of 3450 rpmor higher . b . Always use unbroken , balanced blades de - signed to fit this saw's 5 / 8 inch arbor . c . When thru - sawing ( making cuts where the blade comes through the workpiece top ) , always use a 10 inch diameter blade . This keeps the Spreader inclosest to the blade . d . Do not overtighten arbor nut . Use arbor wrenches to " snug " itsecureiy . e . Use onlysharp blades withpropedy setteeth . . . . Consult a professional bladesharpenerwhen nailsor foreign objects inthe part of the workpiece in doubt . to be cut . f . Keep blades clean of gum and resin . 28
Page: 29

F . Push the workpiece against the rotation of the D . PlanyourcuttoavoidKICKBACKSandTHROW - blade . NEVER feed materiat into the cuttingtool BACKS - when a part or allof the workpiece binds from the rear of the saw . on the blade and is thrown violently back toward the front of the saw . G . Always push the workpiece all the way past the sawblade . 1 . Never cut FREEHAND : Always use either a Rip Fence , Miter Gauge or fixture to position H . As much as possible , keep your face and body to and guide the work , so it won't twist , bind onthe one side of the sawblade , outof linewith apossible blade and kickback . kickback or throwback . 2 . Make sure there's no debris between the work - WHENEVER SAW BLADE iS SPiNNiNG piece and its supports . WARNING : Do , ' t let familiarity ( gained from fre - 3 . Whencutting irregularly shaped workpleces , quent use of your table saw ) cause s careless plan your work so it will not slip and pinch the mistake . AJways remember that • careless frac - blade : tion of a second is enough to cause a severe a . A piece of molding , for example , must fieflat injury . or be held by a fixture or jig that will not let it 1 . Before actuafly cutting with the saw , watch it while it twist , rock or slipwhile being cut . Use jigs or runs for a short while . If it makes an unfamiliar noise fixtures where needed to prevent workpiece or vibrates a lot , stop immediately . Turn the saw off . shifting . Unplug the saw . Do not restart until finding and fixing b . Use a different , better suited type of tool for the problem . work that can't be made stable . 2 . Make sure the top of the arbor or cutting tool turns 4 . Use extra caution with large , very small or toward the front of the saw . awkward workpieces : 3 . Set the cutting tool as low as possible for the cut a . Use extra supports ( tables , saw horses , you're planning . blocks , etc . ) foranyworkpieces large enough 4 . KEEP CHILDREN AWAY . All visitors should be kept to tip when not held down to the table top . a safe distance from work . Make sure bystanders are NEVER use another person as a substitute clear of the saw and workpiece . for a Table Extension , or as additional sup - port for a workpiece that is longer or wider 5 . Let the blade reach full speed before cutting . than the basic saw table , or to help feed , 6 . DON'T FORCE TOOL . It will do the job better and support or pull the workpiece . safer at its designed rate . Feed the workpiece intothe b . Neverconfinethe piece being cutoff . That is , blade only fast enough to let it cut without bogging the pieceNOTagainstthe Fence , Miter Gauge down or binding . or fixture . Never hold it , clamp it , touch it , or 7 . Before freeing any jammed materiah use length stops against it . It must be free to A . Turn switch ' _ FF " . move . Ifconfined , itcouldgetwodgedagainst B . Unplug the saw . the blade and cause a kickback or throw - C . Wail for aft moving parts to stop . back . D . Check blade , Spreader and Fence for proper align - c . Never cut more than one workpiece at atirne . ment before starting , again . d . NEVER turn the saw " ON " before clearing 8 . To avoid throwback of cut off pieces ; the table or all tools , wood scraps , etc . , except the workpiece and related feed or A . Use the Guard Assembly . support devices for the cut planned . B . To remove loose pieces beneath or trapped inside 4 . Plan the way you will push theworkpiece through the Guard : 1 . Turn saw " OFF " . A . NEVER pug the worlkp | ece through . Start and finish the cut from the front of the table saw . 2 . Remove Switch Key . B . NEVER put your fingers or hands in the path of 3 . Wait for blade to stop before lifting the Guard . the sawblade or other cutting tool . BEFORE LEAVING THE SAW C . NEVER reach In back of the cuttingtoolwith either 1 . Turn the saw off . hand to hold - down or support the workpiece , re - 2 . Wait for blade to stop spinning . move wood scraps , or for any other reason . 3 , Make workshop child - proof . Lock the shop . Discon - D . Avoid awkward operations and hand positions nect master switches . Remove the yellow Switch where a sudden slipcould cause tinge rs orhand to Key . Store it away from children and others not move into a sawblade or other cutting tool . qualified to use the tool . E . DONT OVERREACH . Always keep good footing 4 . Unplug the saw . and balance . 29
Page: 30

basic saw operation - using the miter gauge WORK FEED DEVICES SLIGHTLY LESS THAN THICKNESS OF WORKPIECE Before cutting any wood on your saw , study all of the UP TO 3 / 8 " " Basic Saw Operation . " As you learn new table saw woodworking techniques , you'llsee that many types of cuts need different support and feedingdevices , known as jigsor fixtures . They can 45 ° NOTCH help you make cuts more accurately . By helping to steadythe workpiece andkeep you away fromthe blade , NOTE . Ai ! dimenstons in inches they can help you safely use your saw for certain cuts . PUSH STICK Many people custom build their own jigs and fixtures . THESE EDGES MUST Jigsand fixtures areoflen unique , designed fora particu - BE PARALLEL 3 / 4 PLYWOOD lar CUt . 4 - 3 / 4 You can use yourtable saw to easilymake many jigsand fixtures . To get you started , we've included instructions \ , for some simple ones . After you have made a few practice cuts , make up these jigs before sta _ ling any 3t8 _ 2 - 1 / projects . Make the push stick first . PUSH STICK AND PUSH BLOCK 5 - 1 / 8 3 / 8 3 / 8 PLYWOOD NOTE Atl Chmens = ons in inches Make the Push Stick using a piece of I x 2 . PUSH BLOCK Make the Push Block using a piece oi3 / 8 in . and 3 ! 4 in . plywood . 3 / 4 PLYWOOD The small piece of wood 3 / 8 x 3 / 8x 1 - 1 / 2 inches should be GLUED to the plywood . DO NOT USE NAILS . This is to prevent dulling the sawblade in the event you mistakenly cut into the Push Block . 1 - 1 / 4 Pos'dion the handle in the center of the plywood and fasten together with glue and woodscrews . THIS FACE AEID AUXILIARY FENCE / WORKSUPPORT EDGE MUST BE PARALLEL 3 / 8 PLYWOOD Make oneusing apiece of 3 / 8 inchand 3 / 4 inch plywood . 5 - 1 / 2 Fasten together with glue and flat head woodscrews . NOTE All dimension in inches Tighten the screws so the flat head is even with the bottom of the wood . WOODSCREWS AUXlUARY FENCE / WORK SUPPORT = = AUXILIARY PANEL WORK SUPPORT Make using a piece of 3 / 4 " x 3 / 8 " plywood . Fasten together with glue and wood screws . Use this Auxiliary Panel Work Supped only when cutting large panels that 3 - 5 / 8 require the Rip Fence to be positioned past the exposed side of the extension . MUST BE PARALLEL NOTE : All dimension in inches AUXILIARY PANEL / WORK S _ 3O
Page: 31

2 . An auxiliary wood facing attached to the Miter Gauge CROSSCUI - rlNG , MITER CUTTING , BEVEL CUT - can help prevent workpiece twistingand throwbacks . TING , COMPOUND MITER CUTTING and when RAB - Attach it to the holes provided . Make the facing long BETING across the end of a narrow workplece , the enough and big enough to support your work . Make MITER GAUGE IS USED . sure , however , it will not interfere with the sawblade WARNING : For your own safety , a _ ays observe I guard . the following safety precautions In addition to the 3 . use jigs or fixtures to help hold any piece too smallto I safety instructions on pages 2 , 3 , 4 , 5 , 29 , & 30 . extend across the full length of the Miter Gauge face during the cut . This lets you properly hold the Miter Gauge and workpiece and helps keep your hands ADDNIONAL SAFETY iNSTRUCTIONS FOR away from the blade . CROSS CUT TYPE CUTS V _ tlle Cutting : Before Starting : 1 . To avoid blade contact , always hold the Miter Gauge 1 . Never use the Rip Fence when crosscutting . as shown in the " BASIC SAW OPERATIONS - US - iNG THE MITER GAUGE . " CROSSCUTTING Crosscut - A cutting or shaping operation made across \ the width of the workpiece . The graduations on the Miter Gauge provide accuracy for average woodworking . In some cases where ex - treme accuracy is required , when making angle cuts , for example , make a trial cut and then re - check it with an accurate square , or protractor . If necessary , the Miter Gauge head can be swiveled _ DPAPER slightlyto compensate for any inaccuracy . NOTE : The space between the Miter Gauge Bar andthe groove inthe table is held to a minimum during manufac - turing . For maximum accuracy when using the Miter Gauge , always " favor " one side of the groove in the table . In other words , don1 move the Miter Gauge from side to side while cutting , but keep one side of the bar riding WARNING : To avoid blade contact or kickback , against one side of the groove . hold the Miter Gauge properly . NOTE : Glue a pieceof sandpaperto the face of the Miter When using the Miter Gauge in the LEFT hand groove , Gauge head . This will help prevent the workpiece from hold the workpiece firmly against the Miter Gauge head " creeping " while it is being cut . with your left hand , and gripthe lock handle with your The Hold - Down Clamp ( optional accessory ) should be right . used on the Miter Gauge for greater accuracy . When usingthe RIGHThandgroove , holdthe workpiece The Miter Gauge maybe used ineither of the grooves in with your right hand and the Lock Handle with your left the table . Make sure it is locked . hand . \ When cutting long workpieces , invert Auxiliary Panel / Work Support and position it on top of the Guide Bars to supportthe workplece as near to the end as possible , ff thisdoes notadequately supportthe workplace , youcan make a simple support by clamping a piece of plywood to a sawhorse . ( See illustrationsabove . ) Use the Hold - Down Clamp ( optional accessory ) on the Miter Gauge for greater accuracy . 31
Page: 32

basic saw operation LEFT HAND REMOVED \ FOR PICTURE CLARITY \ REPETITIVE CUTTING REPETITIVE CU'FI'ING isknown as cuttingaquantityof pieces the same length without having to mark each piece , 1 . Use the Stop Rods ( optional accessory ) only for cuttingduplicate pieces 6 inches long and longer . 2 . Follow allsafetyprecautions andoperationalinstruc - ti0ns for cross cutting . When making repetitive cuts from a long workpiece , make sure it is adequately supported . Use the Hold - Down Clamp ( optional accessory ) on the Miter Gauge for greater accuracy . _ AUXILIARY FENCE / WORK SUPPORT 3 . NEVER USE THE RIP FENCE AS ALENGTH STOP BECAUSE THE CUT - OFF PIECE COULD BIND BETWEEN THE FENCE AND THE BLADE CAUS - ING A KICKBACK . 4 . When making repetitive cuts shorter than 6 inches , clamp a block ofwood 2 inches longto the table to act as a length stop . Do not clampdimctly tothe bottom edge of the table because the " swivel " of the clamp will not grip properly . Piaceasmafl block of wood between the bottom edge of the table and the " ( 3 " clamp . CAUTION : Avoid kickback from twlstlngthe work - piece . When clamplngthe block , make sumthat theend of the block is well In front oftlte saw - blade . Be sure It is champed securely . 6 . Makethe cut , pull the workpiece back , turn the saw 5 . Slide the workpiece along the Miter Gauge until it off , wait for Blade to stop and remove cut off piece touchesthe block , held itsecurely orclamp itwiththe before continuing . Hold - Down Clamp ( optional accessory ) . MITER CUTTING MITER CUTTING is known as cuttingwood at an angle other than 90 ° withthe edge of the wood . Follow the sameprocedure as you would forcrosscutling . Adjustthe Miter Gauge to the desired angle , and lockit , The Miter Gauge may be used ineither of thegrooves in the table . right . Whenusingthe RIGHT hand groove , holdtheworkpiece with your right hand and the Knob with your left hand . Use the Hold - Down Clamp ( optional accessory ) on the Miter Gauge for greater accuracy . 32
Page: 33

BEVEL CROSSCUTTING BEVEL CROSSCUTTING is the same as crosscutting except that the wood is also cut at an angle , other than 900 with the flat side of the wood . Adjustthe blade to the desired angle . Use the Miter Gauge in the groove to the RIGHT of the blade . It cannot be used in the groove to the LEFT because the Blade Guard will interfere . Hold the work - piecewith your righthand and the LockHandle withyour left hand . Use the Auxiliary Fence / Work Support for additional support of the workpiece . Lay it across the Guide Bars to supportthe workpiece as near to the end as possible . Use the Hold - Down Clamp ( optional accessory ) on the Miter Gauge for greater accuracy . COMPOUND MITER CUTTING COMPOUND MITER CUTTING is a combination of mitercutting and bevel crosscutting . The cut is made at an angle other than 90 ° to both the edge and the flat side of the wood . Adjust the Miter Gauge and the blade to the desired angle . Make sure Miter Gauge is locked . 5 . A FEATHERBOARD can help guide the workpiece . using the rip fence 24 " _ RIPPING , BEVEL RIPPING , RESAWING AND RAB - BETING are performed using the RIP FENCE together withthe AUXILIARY FENCFJWORK SUPPORT , PUSH 5 / 16 " APART KERFS ABOUT 11 ' STICK OR PUSH BLOCK . the following safety precautions in addition to the Before starting : l WARNING : For your own safety , always observe I ] safety instructions on pages 2 , 3 , 4 , 5 , 28 , 29 & 30 . 1 . To avoid kickbacks and slips into the blade , make sure the Rip Fence is parallel to the sawblade . 2 . Check the Anti - Kickback Pawls . The Pawls must ADDITIONAL SAFETY INSTRUCTIONS FOR stop a kickback once it has started . Replace or RiP TYPE CUTS sharpen Anti - Kickback Pawls when points become dull , 1 . NEVER use the Miter Gauge when ripping . 2 . Use a Push Stick whenever the fence is 2 or more 3 . Plastic and composition ( like hardboard ) materials inches from the blade . When thru - sawing , use an may be cut on your saw . However , since these are usually quite hard and slippery , the Anti - Kickback Auxiliary Fence and Push Blockwhenever the Fence must be between 1 / 2 inch and 2 inches of the blade . Pawls may not stop a kickback . Therefore , be espe - cially careful in your set - up and cutting procedures . Never thru - saw ripcuts lessthan 1 / 2 inchwide . While cutting : 3 . When using a Push Stick or Push Block , the trailing 1 . To avoid kickbacks and slips into the blade , always end of the board must be square . A Push Stick or push forward onthe sectionof the workpiece between Block against an uneven end could slipoffor push the the sawblade andthe Rip Fence . Never push forward work away from the fence . on the piece being cut off . 4 . Never rip anything shorter than 10 inches long . 33
Page: 34

ALWAYS SUPPORT LONG WORKPIECES basic saw operation RIPPING Ripping - A cutting or shaping operation along the length of the workpiece . Positionthe Fence to the desired WIDTH OF RIP and lock in place . Before starting to dp , be sure : 1 . Rip Fence is parallel to sawblade : 2 . Spreader is properly aligned with sawblade . 3 . Anti - Kickback Pawls are functioning properly . When ripping LONG BOARDS or LARGE PANELS , always use a work support . A simple one can be made by clamping a piece of plywood to a sawhorse . USING FEATHERBOARDS FOR THRU SAWING Featherboards are NOT employed for thru - sawing operations when usingthe Miter Gauge . Featherbaords are used to keep thework in contact with the Fence and table as shown , and to help stop kick - backs . Add 7 - 1 / 2 inches highflat facing boardtothe Fence , the full length of the Fence . Mount Featherboards to Fence and table as shown , so that leading edges of Featherboards will support work - piece . the edge presses only on the uncut porUon ( for - " ' C " CLAMPS ward of the blade ) . It might otherwise Inch the I WARNING : Make sure the Featherboard against I FEATHERBOARD blade in the kerf and cause a kickback . S FEATHERBOARD Before starting the operation ( switch " OFF " and cutter WORK SUPPORT below table sudace ) : 1 . Install Featherboards so they exert pressure on the workpiece ; be positivetheyare secure , and 2 . Make sure by trialthat the Featherboards will stop a kickback if one should occur . 34
Page: 35

BEVEL RaPPBNG When bevel ripping material 6 inches or narrower , use Fence on the right side of the blade ONLY . This will provide more space between the Fence and the saw - blade for use of a Push Stick . if the Fence is mounted to the left , the Sawblade Guard may interferewithproper use of a Push Stick . Keep your hands out of the blade path . on the part of the workplece that wlil pass be - JWARNING : To avoid kickback , push forward only _ Neen the blade and the fence . Stop your thumbs at the front edge of the table . Finish the cut with the appropriate pusher . Once the trailing end is on the table : When " WIDTH OF RIP " is 2 incheswide or more , usethe Push Stick to finishpushingthe work allthe way past the blade . When thru - sawing a rip 1 / 2 inch to 2 inches wide , the Push Stick CANNOT be used because the Guard will interfere . USE the Auxiliary FencelWork Support and Push Block . Attach Auxiliary Fence / Work Support to Rip Fence with two " C " clamps . 35
Page: 36

basic saw operation Feed the workpiece by hand along the Auxiliary Fence until the end is approximately I inch past the front edge of the table . Continue to feed using the Push Block . Holdtheworkpiece in positionand installthe Push Block by sliding it on top of the Auxiliary Fence , NVork Support ( this may raise Guard ) . BAFFLE WARNING : To avoid blade contact , never thru - J I saw a rip less than 1 / 2 Inch wide . Narrow strips thicker than the Auxiliary Fence / Wod _ Support may enter the Guard and stake the Baffle . CAREFULLY raise Guard only enough to clear the workpiece . Use Push Block to complete cut . RESAWING RESAWING isknown as ripping apiece of wood through its thickness . Do not attempt to resaw BOWED or WARPED material . NOTE : To RESAW a piece of wood wider than 3 - 3 / 8 inches , it will be necessary to remove the blade guard andusetheAuXilia _ , Fence / WorkSupport . ( See " WORK OF WOOD Clamp it to the table so that the workpiece will SLIDE / EASILY but not TILT or MOVE SIDEWAYS without BINDING between the two Fences . Do not clamp directly to the bottom edge of the table because the " swivel " of the clamp will not grip properly . 2 . Make the first pass to a depth slightly more Place a small block of wood between the bottom edge of than 1 / 2 thewidth of the board . Keepthe same the table and the " C " clamp . face of the board against the fence for the second pass . 3 . Instal ! Blade Guard Immediately upon comple - 1 . Do not " Back up ( reverse feeding ) while WARNING : For your own safety : ! tion of the resawlng operation . resawlng because this COUldcause a kickback . 36
Page: 37

AUXILIARY PANEL / CUTTING PANELS When cutting panels ( whenever fence is positioned outside of table sudace ) , ALWAYS use the Auxiliary Fence / Work Suppod . 1 . Unlock Fence and raise rear end . 2 . Position Auxiliary Fence / Work Support as shown and attach it with two " C " clamps . RABBETING RABBETING is known as cutting out a section of the comer of a piece of material , across an end or along an edge . To make a RABBET requires cuts which do not go all the _ FIRST CUT 1 way through the material . Therefore , the Blade Guard RABi must be removed . SECOND CUT 1 . Remove Blade Guard . , f 2 . For rabbeting along an edge ( long way of work - piece ) as shown , add facing to Rip Fence approxi - / / mately as high as the workpiece is wide . Adjust Rip Fence and blade to required dimensions ; then make RABBL _ ' ING ALONG first cut with board flat on table as any rip ( type ) cut ; THE EDGE make second cut with workpiece on edge . Follow all precautions , safety instructions , and operational in - structions as for ripping , or rip type operations , includ - , J ing Featherboards and Push Stick , etc . / 3 . For rabbeting across an end , for workpiece 10 - 1 / 2 inches and narrower , make the rabbet cut with the / board flat on the table . Using the Miter Gauge fitted / with a Facing , follow the same procedures and in - / / structions for cross cutting making successwe cuts / t across the width o ! the workpiece to obtain the de - / / RABBETING sired width of cut . DO NOT use the Rip Fence for ACROSS THE END rabbeting across the end . guard Immediately upon completion of rabbeting I WARNING : For your own safety , Install blade operation , Rabbet cuts can also be made in one pass of the workpiece over the cutter using the Dado Head or Molding Head . PLOUGHING AND MOLDING MOLDING is shaping the workpiece with the grain the PLOUGHING is grooving with the grain the long way of long way ot the workpiece , using the Fence , Use the workpiece , using the Fence . USE featherboards featherboards and push sticks as required , and push sticks as required . MOLDtNG PLOUGHING 37
Page: 38

basic saw operation DADOING Instructionsfor operating the Dado Head are contained in booklet furnished with the Dado Head . The arbor on the saw , is only long enough so that the widest cut that can be made is 13 / 16 inch wide . It is not necessary So install the outside loose collar I before screwing on the artx > rnut . Make sure the arbor LOOSE COL ! . nut is tight . Ill ALWAYS USE DADO INSERT LISTED UNDER " REC - iU SAW ARBOR ARBOR OMMENDED ACCESSORIES . " When using the Dado Head it will be necessary to remove the Blade Guard and Spreader . USE CAU - TION . USE MITER GAUGE , FENCE , FEATHER - BOARDS OR PUSH STICKS , etc . AS REQUIRED . REMOVE SAWBLADE AND INSTALL DADO HEAD WARNING : For your own safety , always replace ] the blade , guard and spreader when you are BACK OF SAW I finished dadoing . MOLDING CUTTING Instructions for operating the Molding Head are con - remove the Blade Guard and Spreader . USE CAU - TION . USE MITER GAUGE . FENCE , FEATHER - tained in a booklet furnished with the Molding Head . BOARDS OR PUSH STICKS , ETC , AS REQUIRED . Always use the Molding insert listed under " RECOM - MENDED ACCESSORIES ' . the blade guard and spreader when you are fin - When using the Molding Head , it will be necessary to j WARNING : For your own safety , always replace I I I _ ted molding . " C " CLAMPS USING FEATHERBOARDS FOR NON - FEATHERBOARD THRU SAWING " C CLAMPS " C ' _ CLAMPS WORK Featherboards are not employed during non thru - saw - ing operations when using the Miter Gauge . Use Featherbaords for all other non thru - sawlng operations ( when sawbladeguard must be removed ) . Featherboards are used to keep the work incontact with the fence and table as shown and to stop kickbacks . Add 7 - 1 / 2 inch highflat facing board tothe fence , the full length of the fence . Mount Featherboard to fence and table as shown , so that leading edges of Featherbaords will support workpiece until cut is complete , and the Stick , as in ripping . Before starting the operation ( switch " OFF " and cutter belowtable surface ) : 1 . Install Featherboards se they exert pressure on the workpiece ; be positive they are secure and 2 . Make sure by trial that the Feathe _ boards will stop a kickback if one should occur . Replace the sawblade guard as soon as the non thnu - sawing operation is complete . 38
Page: 39

adjustments " OFF " and remove plug front POwer source outlet before making any adjustments , MITER GAUGE NOTE : The slots for the Stop Pin and the graduations are manufactured to very close tolerances which pro - videaccuracy foraveragewoodworking . In somecases wh _ e extreme accuracy is required , when making angle cuts , for example , make a tdal cut and then recheckit . If necessary , the Miter Gauge head can be swiveled slightlyto compensate for any inaccuracy . 1 . Loosen the " knob " and pull " Stop Pin " OUT . 2 . Swivel the head , positionit at " 0 " , push the Stop Pin _ 4 IN , lock the Handle . 3 . The HEAD should be square with the Bar and the Pointer should point to " 0 " . Readjust the Pointer if necessary . 4 . If the head is notsquarewith the Bar , adjustments are required . A . Loosen the " knob " ( 1 ) and the " two screws " ( 2 ) 1t8 IN . SETSCREW LH ' - WRENCH 2 B . Position the HEAD square with the Bar using a combination square . F . The Miter Gauge head must rest on top of the Bar C . PUSH the Stop Pin intothe slot in the head at " 0 " , without being able to move up and down , yet it push the Pin into the slot and twist it . Lock the Knob . must swivel freely . G . The swive | ing movement of the head can be ad - D . Recheck with the square . If the head is still not justed by tightening or loosening the setscrew ( 4 ) square , loosen the screws ( 2 ) and readjust the Indicator Blcok . using the 1 / 8 inch setscrew wrench . NOTE : The setscrew is located insideof the head . E . With the head square with the Bar and the Pin To reach it , swivelthe headto 60 ° andtumthe Miter pushed into the slot , adjust the Pointer ( 3 ) to point to " 0 " . Gauge upside down . i HEELING ADJUSTMENT OR PARALLELISM OF SAWB LADE TO MITER GAUGE GROOVE While cutting , the material must move in a straight line PARALLEL to the SAWBLADE . Therefore , both the Miter Gauge Groove and the Rip Fence must be PAR - ALLEL to the Sawblade . WARNING : The blade must be parallel to the miter gauge groove . Misallgned blades could bind on workplace . Workplece could suddenly kickback . You could be cut or hit . If the sawbiade IS NOT parallel to the Miter Gauge Groove , the blade will bind at one end of the cut . ( This is known as " HEELING ' ) . To check for parallelism : 1 . Raise blade aft the way up , raise Blade Guard . make sure switch is " OFF " and plug is not con - 2 . Mark an " X " on one of the teeth which is SET ( bent ) I WARNING : To = wold Injury front accidental start , nected to power source outlet . to the LEFT . 39
Page: 40

adjustments 3 . Place the head of a combination square in the tooth again touches blade of square . GROOVE . Adjust blade of square so that it just 5 . If tooth touches square at FRONT and REAR . touches the tip of the MARKED tooth . sawblade is PARALLEL to Miter Gauge Groove . 4 . Move square to REAR , rotate blade to see ifMARK ED o 6 . If tooth does not touch the same amount , the mecha - nism underneath must be adjusted to make the blade PARALLEL to GROOVE . A . Rear Trunnion must be moved TOWARD to com - REAR TRUNNION FRONT TRUNNION bination square ifthere is aspace between marked tooth and end of square in step 4 . B . Rear Trunnion must be moved AWAY from the square if marked tooth pushes square out of posi - tion in the groove . REAR - TRUNNION SCREWS 7 . Loosen all th tee screws that holdthe Rear Trunnion and all three screws that hold the Front Trunnion . ° NOTE : All six screws can be reached through back of saw . Use a 9 / 16 inch wrench . To reach left - hand Front Trunnion screw , tilt blade to 45 ° . After loosen - ing screws , reposition blade at 90 ° . RIGHT - HAND I CENTER ( BEHIND HERE ) ( BEHIND HERE ) / \ FRONT - TRUNNION SCREWS EDGE OF TRUNNION CLAW HAMMER 8 . Using a wood block and mallet , as shown , move Rear Trunnion to right Or left as required to realign the j WOOD BLOCK blade . If necessary , shift Front Trunnion in similar manner ; but do NOT move Front Trunnion unless necessary . Recheck the alignment with the square , then securely retighten all six Trunnion screws . PLACE BLOCK HERE EDGE OF REAR OF SAW CRADLE 4O
Page: 41

BLADE TILT , OR SQUARENESS OF BLADE TO TABLE When the Bevel Pointer is pointing directly to the " 0 " mark on the Bevel Scale , the sawblade should make a SQUARE cut 90 ° to the table . 90 ° Position To check for SQUARENESS : ' OFF " and remove plug from power source out - WARN , NG : For your own ufety , turn switch J let , 1 . Raise blade all the way UP , raise Blade Guard . 2 . TiLT blade a few degrees to the LEFT . Now , tilt blade back to the RIGHT as far as it will go . 3 . Place the square against blade . Make sure square is not touching the TIP of one of the saw TEETH . 4 . Operate the Tilt - Lock Handle ( COUNTERCLOCK - I ' " i JI ! WISE ) to loosen the Tilt Clamp screw . : LAMP SCREW 5 . NOTE : Handle is spdng loaded forengagementwith ; K HANDLE screw head - must be pushed inward fordisengage - ment whenever necessary to obtain a new gdp on screw head . 6 . Rotate Tilt Handwheel CLOCKWISE afewtumstotilt blade . Now , rotate Handwheel COUNTERCLOCK - WISE until it stops . Blade should now be square with table and Pointer should point to " 0 " . TILT HANDWHEEL BEVEL SCALE A . It blade is SQUARE to table ; POINTER , ADJUSTING SCREW 1 . Check Pointer , B . IF POINTER DOES NOT point to the " 0 " mark on the Bevel Scale ; 1 . Remove Elevation HandwheeL \ 2 , Loosen screw and adjust Pointer using medium SCALE ADJUSTING SCREW screwdriver 3 . Install Elevation Handwheel , POINTER AT " 9 " POSITION 41
Page: 42

adjustments C . If blade is NOT SQUARE to table . . , the 90 ° Stop Screw must be ADJUSTED , 1 . Unscrew 90 ° Stop Screw three to four turns using 3 / 16 inch Hex " L " wrench . 2 . Turn Tilt Handwheel clockwise one turn , then \ tum Handwheel counterclockwise untilblade is ! Q square with table . \ ! 90 ° \ 3 . Screw 90 ° Stop Screw IN until it stops . Check STOPSCREW \ once again for squareness and readjust screw , / necessary . 45o Posrrtion TILT blade to LEFT as far as it will go . 1 . Place an ACCURATE square against blade . Make sure square is nottouching the TIP of one of the saw TEETH . If blade is 45 ° to table ; 1 . Check Pointer . If blade is NOT 45oTO TABLE . . . STOP SCREW and SCALE must be ADJUSTED . 1 . LJnscrew 45 = Stop Screw three to fourturns using \ 3 / 16 inch setscrew wrench . \ \ 2 . Turn Tilt Handwheel until bladeis45 oto the table . ! © ! \ 3 , Screw 45 ° Stop Screw IN untilil stops . Check once 45 ° again and readjustscrew , if necessary . \ STOPSCREW ! \ If POINTER DOES NOT point to the 45 ° markon the scale ; 1 . Remove Elevation Handwheel . 2 , Loosen two screws on Scale and adjust Scale until Pointer pointsto 45 ° mark , 3 . Install Elevation Handwheel . o TILT MECHANISM The Handwheel shou TILT HANDWHEEL ADJUST THESE TWO SCREWS 42
Page: 43

maintenance WARNING : For your own safety , turn switch " OFF " and remove plug from power source outlet before maintaining or lubricating your saw . Do not allow sawdust to accumulate inside the saw . Frequently blow out any dust that may accumulate inside the saw cabinet and the motor . Frequently clean your cutting tools with a solvent recom - mended for gum and pitch removal . A coat of automobile - type wax applied to the table will help to keep the surface clean and allow workpieces to slide more freely . 2 . Rotate Pawl toward rear of Spreader so that teeth are If the power cord is worn or cut , or damaged in any way , above top of Spreader . have it replaced immediately . 3 . Hold Spreader with left hand and place Pawl over cor - Make sure the teeth of the Anti - Kickback Pawls are always ner of workbench . sharp . To sharpen : 4 . Using a small round file ( smooth cut ) sharpen the 1 . Remove Blade Guard . teeth . lubrication " / - - The following parts should be oiled occasionally with SAE No . 20 or No . 30 engine oil . 1 . Tilt screw threads and pivot nut . ( First clean with a sol - vent recommended for gum and pitch removal . ) 2 . Elevation screw threads and pivot nut . ( First clean with a solvent recommended for gum and pitch removal . ) 3 . Cradle bearing points . 4 . Bearing points in Guard Assembly , Miter Gauge and Rip Fence . 7 - f _ 0 BENRING POINTS sears recommends the following accessories ITEM CAT NO . Item CAT . NO . Miter Gauge Stop Rods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 29924 Caster Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 22222 or 9 - 22221 Miter Gauge Hold - Down Clamp . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 29928 7 In . Molding Head Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Catalog Taper Jig . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Catalog 7 In . Molding Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Catalog Universal Jig . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Catalog 8 In . Molding Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Catalog Power Tool Know How Handbook . . . . . . . . . . . . . . . . . . . . . . 9 - 29117 MoldingJDado Insert for 7 In . Dia . Molding or Dado Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 29997 Sears may recommend other accessories not listed in Molding / Dado Insert for 8 In . Dia . Molding manual . or Dado Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 22287 See your nearest Sears store for other accessories . Work Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Catalog Do not use any accessory unless you have receive _ 7 In . Dia . Adjustable Dado Head . . . . . . . . . . . . . . . . . . See Catalog and read complete instructions for its use . 7 In . Dia . Dado Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Catalog Sanding Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Catalog ' WARNING : Use only accessories recommended for this saw , Using other accessories may be dangerous . J 43
Page: 44

trouble shooting WARNING : For your own safety , turn switch " OFF " and always remove plug from power source outlet before troubleshooting . TROUBLE SHOOTING - GENERAL TROUBLE PROBABLE CAUSE REMEDY Excessive vibration 1 . Blade out of balance . 1 . Discard Blade and use a different blade . Cannot make square 1 . Miter gauge not adjusted 1 . See " Adjustments " section " Miter Gauge . " cut when crosscutting . properly . Cut binds , burns or 1 . Dull blade or improper 1 . Sharpen or replace blade . stalls motor when tooth set . npp = ng . 2 . Blade is Heeling . 2 . See " Adjustments " section , " Heeling Adjustment . . " 3 . Warped board , 3 . Make sure concave or hollow side is facing " down , " feed slowly . 4 . See " Assembly " section , " Aligning Rip Fence . " 4 . Rip Fence not parallel to blade . 5 . Spreader out of alignment . 5 . See " Assembly " section , " Installing Blade Guard . " Cut not true at 90 ° or 1 . See " Adjustments " section , " Blade Tilt , or 1 . Stop collars not properly 45 ° positions . adjusted . Squareness of Blade to Table . " 1 . See " Maintenance " and " Lubrication " sections , Tilt and elevating f . Sawdust on threads of tilt handwheel turn hard , screw or elevat = ng screw . • 2 . Bearing retainers too 2 . See " Maintenance " section , " Tilt and Elevation tight . Mechanism " TROUBLESHOOTING - MOTOR NOTE : Motors used on wood working tools ar particularly susceptible to the accumulation of sawdust and wood chips and should be blown out or " vacuurned " frequently to prevent interferencewith normal motor ventilation , reduction of 36 % in maximum power output . } 44
Page: 45

TROUBLESHOOTING . MOTOR ( Cont'd ) TROUBLE PROBABLE CAUSE REMEDY iiiiiii ill ii ii iiii . Motor starts slowly 1 . Low voltage . Request voltage check from the power company . 2 . or fails to come up 2 . Windings burned out Have motor repaired or replaced . to lull speed or open . 3 . Starting switch not 3 . Have switch replaced . operating . Motor overheats 1 . Motor overloaded , Feed work ' slower into blade . 2 . 2 . Improper cooling . ( Air Clean out sawdust to provide normal air circulation circulation restricted through motor . See " Maintenance " and " Lubrication " section . through motor due to sawdust , accumulating inside of saw . ) ' 11 " Burned switch contacts Starting switch in 1 . Have switch replaced and request a voltage check " motor will not ( due to extended hold - in from the power company . operate periods caused by low line voltage , etc . ) 2 . Shorted capacitor 2 . Have capacitor tested and replace it defective . ( when equipped ) 3 . Loose or broken 3 . Have wiring checked and repaired . connections . Motor sialls . 1 . Starting switch not 1 . Have switch replaced . ( resulting in blown operating . fuses or tripped 2 . Voltage too low to permit 2 . Request voltage check from the power company . circuit breakers ) motor to reach operating speed . 3 . Fuses or circuitbreakers 3 . Install proper size fuses or circuit breakers . do not have sufficient capacity . 1 . Motor overloaded 1 . Feed work slower into'blade . Fre'quent opening of fuses or circuit 2 . Fuses or circuitbreakers 2 . Install proper size fuses or circuit breakers . breakers do not have sufficient capacity , 3 . Have switch replaced . 3 . Starting switch not operating ( motor does not reach speed . ) 45
Page: 46

PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAW MODEL NO . 113 . 298722 AND 113.298762 4 . . - _ ) 8 7 4O 32 33 37 \ / / 41 31 3O FIGURE 1
Page: 47

PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAW MODEL NO . 113 , 298722 AND 113.298762 FIGURE 1 - PARTS LIST KEY PART PART NO . 1 ! O . DESCRIPTION NO . NO . DESCRIPTION ! 1 23 STD511107 * Screw , Pan Hd . 10 - 32 x 3 / _ t . . . . . . . Guard Assembly ( See Fig . 7 ) 2 STD522506 * Screw , Hex Hd . 1 / 4 - 20 x 5 / 8 24 STD551210 * Lockwasher , External No . 10 , STD551225 3 * Lockwasher , External1 / 4 25 820452 Handwheel 4 STD541025 * Nut , Hex ! t4 . 20 26 STD511103 " Screw , Pan Hd . 10 - 32 x 3 / 8 5 STD523110 * Screw , Hex 5 / 16 - 18 x 1 27 819435 Panel , Front 818315 Bar , Fence Rear 28 STD610805 Screw , Pan Hd . Ty " AB " No . 8 x 1 / 2 STD551231 * Lockwasher , External 5 / 16 29 818548 Scale , Adjustable Bevel 8 STD541231 * Nut , Hex 5 / 16 - 18 30 62700 Base 9 62703 31 60252 Insert Assembly ( Includes Key No . 11 & 12 ) Guard , Belt 10 62718 32 60255 Clip , Retaining Clip , " S " 11 33 STD601105 STD501102 * Screw , Locking Set 10 - , 32x 3 / 16 * Screw , PanHd , Ty ' T ' 10 - 32 x lf2 ! 2 447441 34 60253 Screw , FlatHd , 10 - 32x 1 SupportB , et'G { uard 13 62493 35 60254 Insert , Exact + Cut Bracket , Support 14 36 423567 Fence Assembry , Rip ( See Fig . 5 ) * Screw , Hex Hd . 3 / 8 - 16 x 112 15 62710 Tape , Fence 37 STD551237 Lockwasher , External 3 / 8 16 62709 Bar Assembly , Fence Guide 38 71165 Tie , Wire 39 STD541411 ( Includes Key No . 15 ) * Nut , Lock 10 - 32 17 62539 40 820176 Motor Spacer , Fence Guide Bar 18 40 820030 Switch Assembly , Box ( See Fig . 3 ) Motor ( Model 113 . 298762 only ) 19 STD523117 * Screw , Hex Hd . 5 / 16 - 18 x 1 - 3 / 4 41 69184 Bracket , " L " Mounting 20 STD551031 * Washer , 21 / 64 x 5 / 8 x 1 / 16 ( Model 113.298722 only ) 21 STD523107 * Screw , Hex , 5 / 16 - 18 x 3 / 4 SP5627 Owners Manual ( Not Illustrated ) 22 Gauge Assembly , Miter ( See Fig . 6 ) buying these items by mail uneconomical . To avoid shipping and * Standard Hardware Item - May be purchased locally . handling charges , you may obtain most of these locally . NOTE : Shipping and handling charges for standard hardware items ( identified by * ) such as nuts , screws , washers , etc . , make
Page: 48

( I ) PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAW " 0m MODEL NO . 113 . 298722 AND 113.298762 ml " 0 9.1 U ) 19 20 21 22 _ 4 15 16 co 25 / J 23 51 50 49 29 3O 38 37 36 35 34 34 49 \ 33 32 FIGURE 2
Page: 49

PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAW MODEL 113.298722 AND 113,298762 FIGURE 2 - PARTS LIST KEY PART PART KEY NO , NO . DESCRIPTION DESCRIPTION NO . NO . 3 " 1 STD581062 * Ring , Retaining5 / 8 . . . . . . . . . . Support , Spreader 32 37838 Washer , . 629 x 7 / 8 x 1 / 64 Screw , Thumb 5 / 16 - 18 x 1 2 160204 33 60178 Washer , Spdng * Pin , Roll 3 / 16x 1 - 1 / 4 3 I STD571812 34 STD302111 * O - Ring 4 I STD523106 Screw , Hex Hd . 5 / 16 - 18 x 5 / 8 35 62697 Screw , Lift Screw , Hex Hd . 5 / 16 - 18 x 1 5 I STD523110 36 62699 Pointer * Lockwasher , External 5 / 16 6 I STD551231 37 STD601103 * Screw , Pan Hd . Ty " T " 10 - 32 x 3 / 8 Support , Guard 7 162292 38 STD551210 * Lockwasher , External No . 10 * Nut , Hex 5 / 16 - 18 8 1STD541231 39 819442 * + Bolt , Carriage 5 / 16 - 18 x 3 / 4 Cradle ( Includes Key No . 40 ) 9 I STD533107 40 6527 Ring , Retaining 3 / 4 * Screw , Hex Ind . Wash . Hd . 1 / 4 - 20 x 1 - 1 / 2 10 160206 41 60384 Washer , 3 / 4 x 1 - 1 / 4 x . 090 Spring 11 16o2o5 * wasi _ er , . 380 x 47 / 64 x 3 / 32 12 I STD551037 43 508511 Arbor Washer , Knob Clamp 13 163011 44 60400 Ring , Retaining 5 / 8 Spacer 14 162296 45 STD580025 Table , Trunnion * Key , Woodruff ! 5 162833 46 819432 Table , 10 In . Saw Housing , Arbor 16 ] 818319 47 820015 Screw , Soc . Set 3 / 8 - 16 x 3t4 Bearing , Saw Arbor 17 1818463 48 37158 1 " Blade , Saw 10 In . Ring , Retaining 5 / 8 18 19 - 32138 49 STD326022 * Pulley , 5 / 8 Bore ( Includes Set Screw ) Collar , Blade 19162498 50 STD304410 Nut , Arbor * Belt , V 1 / 2 x 41 20 I 6362 51 STD581037 Wrench , Arbor Ring , Retaining 3 / 8 2113540 52 37823 Pin , Hinge Retainer , Bearing 22 162437 53 37824 Base , Motor 23 162898 . Screw , Tilt 54 37825 Support , Motor Base Screw , Hex Hd . 3 / 8 - 16 x 1 241ST0523710 55 30628 Screw , Pivot Arm * Lock'washer , Exterrlal 3 / 8 25ISTOSm237 56 6423 Washer , Spring Nut , Tilt 26 013789954 57 STD551025 * Washer , 17164 x 47164 x 1 / 16 27Im Ring , Retaining 3 / 4 58 162585 28 ! 37828 Rod , Spreader Spring , Clamp Screw 29 18 59 30767 Washer End Play ( . 010 Thick ) Handle , Clamp Screw Screw , Clamp 30 37829 * Standard Hardware Item - May be purchased locally 1 " Stock Item - May be secured through the Hardware Department o1 most Sears Retail Stores or Catalog Order Houses .
Page: 50

repair parts PARTS LiST FOR CRAFTSMAN 10 iNCH TABLE SAW MODEL 113.298722 AND 113.298762 ! 2 \ \
Page: 51

PARTS UST FOR CRAFTSMAN 10 iNCH TABLE SAW MODEL NO . 113 . 298722 AND 113.298762 5 \ FRONT GUIDE BAR ( REF ) 4 ! 4 \ REAR GUIDE BAR ( REF ) FIGURE 4 - TABLE EXTENSIONS KEY PART NO . NO . DESCRIPTION 1 9 - 22261 t Extension , Table 12 x 27 2 STD541231 * Nut , Hex 5 / 16 - 18 3 STD551231 * Lockwasher , External 5 / 16 4 STD523107 : * Screw , Hex Head 5 / 16 - 18 x 3 / 4 5 STD551031 * Washer , 21 / 64 x5 / 8 x 1 / 16 6 818308 Bracket 7 62539 Spacer , Fence Guide Bar 8 STD523112 * Screw , Hex Hd . 5 / 16 - 18 x 1 - 1 / 4 * Standard Hardware Item - May be purchased locally 1 " Stock Item - May be secured through the Hardware Department of most Sears Retail Stores or Catalog Order Houses . 51
Page: 52

repair parts PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAW MODEL NO . 113 . 298722 AND 113.298762 t Io , ' - - - - . / J 4 ° 11 17 It , . . - - - - - ts • . i _ FIGURE 5 - RiP FENCE ASSEMB LY KEY , - PART NO . * _ _ NO . • . " DESCRIPTION 1 62942 " , , - . : _ Hand ! e • 2 62945 ' _ Shoe 3 62775 " " Indicator 4 9404336 L " , Screw , Parl . CrossType - - r , No . 4 - 40 x 1 / 4 5 , 62941 : _ Hea _ Fence 6 423567 ' L i " . , _ rew , Sems3 / 8 - 16xli2 7 s2s4s , _ . _ _ , Ctm _ . Fence 8 ST _ 80 _ _ : SCm _ _ CIosstype'T ; 8 - 32x1 / 2 9 szs2a _ • , _ ; s _ pm _ , _ nce ; L . _ : k 13 ; . 508112 " ' ! _ ; _ ; , _ / UJgntne _ ( IncludesKey # 18 ) 15 ÷ STD61 . 100 _ : _ ' ; . : _ , J - k _ xH _ ' Type " A " No . t 0 x 1 / 2 i6 . . . . . . PacL ' _ _ gnrnent 17 62940 " - Cam _ : . . . . . 18 " : 6 , ' Z94 _ _ . ' . . f , b't _ A , djustment , . " • StandardHard , vats - item . May _ bepurchasedlocally . 52
Page: 53

PARTS LiST FOR CRAFTSMAN 10 iNCH TABLE SAW MODEL NO . 113 . 298722 AND 113.298762 - - - - - - - 3 _ 4 td . _ _ _ - - - 7 , o 9 9 FIGURE 6 - MITER GAUGE ASSEMBLY KEY PART . NO . ' NO . ' DESCRIPTION 1 62693 Plug , Button 2 62692 Knob , Miter Gauge ( Includes Key No . 1 ) 3 STD551031 * Washer , Plain , 21 / 64 x 1 x 1 / 16 4 37893 Gauge , Miter 5 STD510803 * Screw , Pan Hd . 8 - 32 x 5 / 16 6 135 Indicator 7 37895 Block , Miter Gauge Indicator 8 37896 Pin , Miter Gauge Stop 9 9417295 * Screw , Pan Hd . , w / Lockwasher , 8 - 32 x 5 / 8 10 62230 Rod Assembly , Miter Gauge , Consisting of Items 11 , 12 , 13 STD541231 11 12 62225 Stud , Clamp 13 62383 " Stud , Pivot 14 Screw , Locking Set 1 / 4 - 20 x 3 / 8 * Standard Hardware Item - May be purchased locally . 53
Page: 54

repair parts PAR'IS LiST FOR CRAF3SMAN 10 INCH TABLE SAW UODEL NO . 1 _ 3 . 298722 AND 113.298762 T 2 3 4 5 I FIGURE 7 ' - GUARD ASSEMBLY DESCRIPTION 54
Page: 55

PARTS UST FOR CRAFTSMAN 10 iNCH TABLE SAW MODEL NO . 113 . 298722 AND 113.298762 3 4 5 / 19 1 2 ® / 6 5 4 1 I t , / 1 6 2 I FIGURE 8 - LEG SET KEY " PART DESCRIPTION NO . NO . Screw , Serrated Truss Hd . 1 / 4 - 20 x 1 / 2 1 60314 2 819441 Leg 3 62554 Stiffener , Side 4 STD551225 * Lockwasher , Ext . 1 / 4 5 STD541025 * Nut , Hex 1 / 4 - 20 6 62553 Stiffener , End 7 STD541237 * Nut , Hex 3 / 8 - 16 8 803835 - 1 Foot , Leveling HARDWARE FOR ATrACHING LEGS TO SAW 9 STD523112 Screw , Hex Hd . 5 / 16 - 18 x 1 - 1 / 4 10 STD551031 Washer , 11 / 32 x 11 / 16 x 1 / ! 6 11 STD551231 * Lockwasher , Ext . 5 / 16 12 STD541231 * Nut , Hex 5 / 16 - 18 * Standard Hardware Item - May be purchased locally 55
Page: 56

10 - iNCH TABLE ; AW SERVICE Now that you have purchased your 10 Inch Table Saw , should a need ever exist for repair parts or service , simply contact any Sears Service Center and most Sears , Roebuck and Co . , stores . Be sure to provide all pertinent facts when you call or visit . MODEL NO'S The model number of your Table saw will be found at the left - hand side of the base . 113.298722 113.298762 WHEN ORDERING REPAIR PARTS , ALWAYS HOW TO ORDER GIVE THE FOLLOWING INFORMATION : REPAIR PARTS PART NUMBER PART DESCRIPTION MODEL NUMBER NAME OF ITEM 113.298722 10 Inch Table Saw 113.298762 All parts listed may be ordered from any Sears Service Center and most Sears stores . If the parts you need are not stocked locally , your order will be electronically transmitted to a Sears Repair Parts Distribution Center for handling . Sold by SEARS , ROEBUCK AND CO . , Chicago , IL 60684 U . S . A . Part No . SP5627 Form No . SP5627 - 2 Printed in U . S . A . 11 / 93
Search in Table Saw on ebay
"