Home | Register Login | Wanted Manuals | MarketPlace | Members Area | Manuals Manufacturer Directory | UPC Lookup | Information Pages | Policy


Back To Craftsman Table Saw       Model: 113.299310 or 113299310 Craftsman Rails and Fence System
Regular Text Search or Search by Model Number

Register / log-in to add to your Hammerwall Collection.
Manual Location


This is a partial text extraction from the pdf, to download the pdf, click the Manual tab. If you want to search this text, hold control and F, and type the word you are looking for.

Page: 1

Owner's Manual II : RRFTSMRN'I RAILS AND FENCE SYSTEM FOR CRAFTSMAN 10 in . TABLE SAWS MODEL NOS . 315.228310 , 315.228410 , 315.228510 , 113.299310 , 113.299410 , 113.299510 Item No . _ 929993 TABLE SAWNOT INCLUDED Save this manual for future reference . • SAFETY _ , CAUTION : Read and follow • LOOSE PARTS all Safety Rules and Operating Instructions before first use of • PREPARATION this product . • INSTALLATION • ALIGNMENT Customer Help Line : 1 - 800 - 932 - 3188 Sears , Roebuck and Co . , Hoffman Estates , IL 60179 USA Visit the Craftsman web page : www . sears . com / craftsman 972000 - 662 3 - 99
Page: 2

READ ALL INSTRUCTIONS • ALWAYS WEAR SAFETY GLASSES . Everyday eyeglasses have only impact - resistant lenses ; • READ THESE INSTRUCTIONS AND THE they are NOT safety glasses . INSTRUCTIONS FOR YOUR TABLE SAW • ALWAYS DISCONNECT SAW FROM POWER THOROUGHLY before using accessories . SUPPLY BEFORE MAKING ADJUSTMENTS KNOW YOUR POWER TOOL . Read the owner's OR ADDING ACCESSORIES . Make sure the manual for the Table Saw carefully . Learn the switch is off when reconnecting to power supply , saw's applications and limitations as well as the • SAVE THESE INSTRUCTIONS . Refer to them specific potential hazards related to this tool . frequently and use to instruct other users . If you KEEP THE WORK AREA CLEAN . Cluttered loan someone this tool , loan them these instruc - work areas and work benches invite accidents . tions also . DO NOT leave tools or pieces of wood on the saw while it is in operation . Look for this symbol to point out important safety precautions . It means attention . q ! Your safety is involved . These included parts make up the the fence and rails accessory 9P9993 . Fasteners are shown actual size . 1 . Fence 2 . Rails A , Fence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 A . Front rail end cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 B . Screw ( 1 / 4 - 20 x 3 / 8 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 B . Screw for end caps ( 5 / 32 - 32 x 1 / 2 in . ) . . . . . . . . . . . 4 C . Fine Adjustment Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 C , Rear rail end cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 D . Front rail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 E . Rear rail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 © O A . C . B . A . B . C . Fig . 1 2
Page: 3

SLOTFORBOLT TABLEEXTENSION REMOVING THE SWITCH AND RAILS • Remove the front rail end caps . • Under the front rail , loosen the switch screws and slide the switch off of the rail . See Figure 2 . Note : Do not remove the switch screws completely . Loosening the screws will allow you to slide the switch off the front rail and the switch will be ready to install on the new front rail , REARRAIL _ _ FRONTRAIL _ TABLE SQUAREHEAD BOLT HEXNUT EXTENSION FLATWASHER Fig . 3 • Remove the rear rail end caps . • Under the table , loosen all of the hex nuts on the SWlTCHSCREW square head bolts that hold both front and rear rails . See Figure 3 . SWITCH SQUARENUT Note : Do not remove the hex nuts completely . Loosening the nuts will allow you to slide the L . _ rails off the table and the square head bolts will be ready for the new rails . • Carefully slide the rails off of the bolts and the table . Fig . 2
Page: 4

INSTALLING THE REAR RAIL • Position rail so that the right hand edge extends 2 - 1 / 2 in . beyond the table extension . A ' _ WARNING : Front and rear rails must be Note : Instructions are given from the operator's carefully aligned to reduce the risk of kickback , position in front of the saw . which can cause serious injury . • Push the rail against table and tighten each hex nut with a 12 mm wrench . If the rail jams or does • From the carton , remove the rear rail and the not slide easily over the bolts , re - align the table following hardware : extensions according to the instructions in the table Right and left end caps for rear rail saw owner's manual . 2 screws ( 5 / 32 - 32 x 1 / 2 in . ) for end caps Note : Make sure there are no gaps between the rail Note : The square head bolts , washers , and hex nuts and edge of table or extensions . shown at the top of figure 3 should still be on the • Put the end caps on the rail ends . Insert the table saw . If you mistakenly removed them , put screws and tighten with a phillips screwdriver . them back on the table . Do not tighten . • Carefully slide the rail onto the square head bolts . SQUAREHEAD BOLT HEXNUT FLAT WASHER SCREW Fig . 4 4
Page: 5

INSTALLING THE FRONT RAIL RAILSLOT HEXNUT • Locate the front rail and the following hardware : Right and left end caps for front rail 2 screws ( 5 / 32 - 32 x 1 / 2 in . ) for end caps • Set aside the end caps and two screws until the switch has been installed . Note : The square head bolts , washers , and hex nuts shown at the bottom of figure 6 should still be on the table saw . If you mistakenly removed them , put them back on the table . Do not tighten . • The back of the rail has two slots . See Figure SWITCHSLOT Carefully slide the upper slot over the bolts . ( Bottom slot is for switch . ) Fig . 7 • Align the rail left to right - Match the 7 - 1 / 8 in . mark TABLETOP VIEWEDFROMABOVE on the right scale to the right edge of the saw base ( main table ) . See Figure 8 . TABLE SAWTABLE • Snug the rail against table . Finger - tighten each nut EXTENSION on the table and extensions . SCALE SCALE FRONTRAIL \ . FRONTRAIL 7 - 1 / 8 in , MARKRIGHTSCALE HEIGHT Fig . 8 HANDWHEEL SQUAREHEAD HEXNUT FLATWASHER Fig . 6
Page: 6

P • Insert the two remaining pan head screws into \ FRONTRAIL holes in the fine adjustment knob bracket . TABLE • Attach the fine adjustment knob bracket to the EXTENSION bottom of the fence head on the right or the left side of the fence handle . Securely tighten the two screws . SWITCHSCREW BRACKET SWITCH ASSEMBLY SCREWS _ _ Fig . 10 Fig . 9 MOUNTING THE SWITCH ENDCAP • Locate the switch assembly , The fasteners should still be attached . Note : If the fasteners were removed from the switch , SCREW see instructions in your table saw Owner's Manual for mounting the switch or refer to Figure 10 . • Holding the switch to the front , insert and slide the two square nuts into the lower slot of the front rail . Fig . 11 _ I , WARNING : Place the switch out of the immedi - ate work area to avoid accidentally turning it off during operation . • Slide the switch assembly to a convenient position , leaving ample clearance for the handwheel . Tighten securely with a screwdriver . • Attach the front rail end caps and screws with a phillips screw driver . See Figure 11 .
Page: 7

ALIGNING THE RIP FENCE AND FRONT RAIL • Remove the rip fence and repeat on the other side of the blade . When the fence rides smoothly , The rip fence scale indicator is installed on the right tighten all rail hex nuts with a 12 mm wrench . side of the rip fence but can be removed and rein - Push in the micro - adjust knob and turn it . The gear stalled on the left side if needed . If a cutting operation • on the shaft assembly will engage the rack teeth requires placing the rip fence on the left side of the on the rack and will move the fence assembly left blade , and you find relocating the indicator necessary , or right . simply unscrew and re - attach it . Push down on the rip fence handle to lock the rip • Hook the back of the rip fence over the rear rail . • fence in place . See Figure 12 . Lowper the front of the rip fence into the groove on the front rail . See Figure 13 . • Slide the rip fence back and forth . It should move TO INSTALL freely with about 1 / 16 in . clearance below the rip INDICATOR ON LEFT fence . If it doesn't , loosen the nuts holding the front SIDE rail and adjust the rail up or down . See Figure 6 . RIPFENCE HOOKOVER REARRAIL HERE REARRAIL Fig . 12 RIP FENCEHANDLE Fig . 13
Page: 8

MITERGAUGEGROOVE FRAMING CHECKING RIP FENCE AND . SQUARE BLADE ALIGNMENT The rip fence is self - aligning but should be checked before first use . _ . WARNING : Failure to align the rip fence to the blade can cause jams and kickback , resulting in serious personal injury . • Slide the rip fence to the miter gauge groove , which is parallel to blade . Do not lock the rip fence . • Place a framing square against the blade , with the long end under the rip fence at the front . See Figure 14 . Note the distance . • Move the square to the back and measure the length from other end of the fence . See Figure 15 . • If the distances are different , loosen the four screws around the rip fence handle with a 6 mm hex key . Alternate the order ( remove the screw opposite , not next to the first one ) . See Figure 16 . ADJUSTMENTSCREWS • Hold the fence handle against the front rail and align the rip fence with the blade . Fig . 15 • Retighten the screws in alternating order and check the alignment . RIPFENCE • Repeat until the rip fence is aligned . MITERGAUGEGROOVE ADJUSTMENT BLADE RIPFENCE SCREWS ( 4 ) RIPFENCE HANDLE Fig . 16 Note : To insure proper self alignment when position - ing rip fence , push sides of scale indicator housing against front rail before locking rip fence handle . MITERGAUGE GROOVE Fig . 14 8
Search in Table Saw on ebay
"