Home | Register Login | Wanted Manuals | MarketPlace | Members Area | Manuals Manufacturer Directory | UPC Lookup | Information Pages | Policy


Back To Craftsman Table Saw       Model: 137.248850 or 137248850 Craftsman 10 In. Table Saw Stand
Regular Text Search or Search by Model Number

Register / log-in to add to your Hammerwall Collection.
Manual Location


This is a partial text extraction from the pdf, to download the pdf, click the Manual tab. If you want to search this text, hold control and F, and type the word you are looking for.

Page: 1

Operator's Manual ® 10 in . TABLE SAW WiTH STAND Model No . 137.248850 e Safety Instructions CAUTION : • Installation Before using this Table Saw , o Operation read this manual and follow e Maintenance all its Safety Rules and • Parts List Operating instructions Sears Parts & Customer Help Line For Technical Support Repair Center 1 - 800 , . 843 - 1682 1 - 800 - 488 - 1222 Sears , Roebuck and Co . , Hoffman Estates , IL 60179 USA Visit our Craftsman website : www . sears . com / craftsman Part No . 137248850001
Page: 2

SECTION PAGE SECTION PAGE Know Your Table Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Power Tool Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Assembly and Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Table Saw Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Electrical Requirements and Safety . . . . . . . . . . . . . . . . . . . . . . 5 Accessories and Attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Tools Needed For Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Carton Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Push Stick Plan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 ONE = YEAR FULL WARRANTY ON CRAFTSMAN TOOL if this Craftsman tool fails due to a defect in material or workmanship within one year from the date of purchase , CALL 1 = 800 = 4 - MY - HOME ® TO ARRANGE FOR FREE REPAIR ( or replacement if repair proves impossible ) . tf this tool is used for commercial or rental purposes , this warranty will apply for only ninety days from the date of purchase . This warranty applies only while this tool is in the United States . This warranty gives you specific legal rights , and you may also have other rights , which vary , from state to state . Sears , Roebuck and Co . , Hoffman Estates , IL 60179 WARNIING Some dust created by power sanding , sawing , grinding , drilling and other construction activities contains chemicals known to cause cancer , birth defects or other reproductive harm . Some examples of these chemicals are : • Lead from lead - based paints • Crystalline silica from bricks , cement and other masonry products • Arsenic and chromium from chemically treated lumber Your risk from these exposures varies , depending on how often you do this type of work . To reduce your exposure to these chemicals , work in a well ventilated area and work with approved safety equipment such as dust masks that are specially designed to filter out microscopic particles . MOTOR SAW Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Universal Rip Capacity With Extension . . . . . . . . 30 in . Right & 18 in . Left Blade Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 in . Amps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Blade Arbor Size . . . . . . . . . . . . . . . . . . . . . . . . . 5 / 8 in . Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Maximum Cut Depth @ 90 ° . . . . . . . . . 3 in . RPM ( no load ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5000 Maximum Cut Depth @ 45 ° . . . . . . . . . 2 - 1 / 2 in . Maximum Diameter Dado . . . . . . . . . . . 6 in . ( Stackable only ) Maximum Dado Cut Width . . . . . . . . . . 1 / 2 in . [ A WARNINI G To avoid electrical hazards , fire hazards or damage to the tool , use proper circuit protection . This tool is wired at the factory for 110 = 120 Volt operation . It must be connected to a 110 = 120 Volt / 15 Ampere time delay fuse or circuit breaker . To avoid shock or fire , replace power cord immediately if it is worn , cut or damaged in any way . Before using your tool , it is critical that you read and understand these safety rules . Failure to follow these rules could result in serious injury to you or damage to the tool .
Page: 3

GENERAL SAFETY iNSTRUCTiONS Read and understand all the instructions below before using the power tool . These safety instructions are not meant to cover every possible condition that could occur . As with any power tool , common sense , vigilance and due care must be used . NEVER LEAVE TOOL RUNNING UNATTENDED . 1 . READ and become familiar with the entire Operator ' 17 . TURN THE POWER " OFF " . Do not leave the tool s Manual . LEARN the tool's application , limitations and possible hazards . before it comes to a complete stop . NEVER STAND ON TOOL . Serious injury could 2 . [ _ k WARNING ] Look for this symbol that 18 . occur if the tool is tipped or if the cutting tool is identifies important safety precautions , it means unintentionally contacted . CAUTION ! Become alert , your safety is involved DO NOT OVERREACH . Keep proper footing and if you do notfollow the safety instructions . 19 . balance at all times . MAiNTAiN TOOLS WiTH CARE . Keep tools sharp 3 . [ _ ' DANG ER _ Look for this symbol that 20 . and clean for most efficient and safest performance . identifies important safety precautions , it means Follow instructions for lubricating and changing CAUTION ! Become alert , your safety is involved accessories . if you do not follow the safety instructions . 21 . CHECK FOR DAMAGED OR LOOSE PARTS . 4 . NEVER OPERATE THiS MACHINE WITHOUT Before further use of the tool , a guard or other THE SAFETY GUARD iN PLACE FOR ALL part that is damaged should be carefully checked THROUGHSAWING OPERATIONS . to ensure it will operate properly and perform its 5 . DO NOT USE iN A DANGEROUS ENVIRONMENT intended function . Check for alignment of moving such as damp or wet locations or exposure to rain . parts , binding of moving parts , loose mounting Keep work area well lighted . and any other conditions that may affect its safe 6 . operation . A guard or other part that is loose or DO NOT use power tools in the presence of damaged should be properly adjusted repaired or flammable liquids or gases . replaced . 7 . KEEP WORK AREA CLEAN . Cluttered areas and benches invite accidents . 22 . MAKE WORKSHOP CHILD PROOF with padlocks , master switches or by removing starter keys . 8 . KEEP CHILDREN AWAY . All visitors should be 23 . DO NOT operate the tool if you are under the kept at a safe distance from the work area . influence of any drugs , alcohol or medication that 9 . DO NOT FORCE THE TOOL . It will do the job could impair your ability to use the tool safely . better and safer at the rate for which it was 24 . USE A DUST COLLECTION SYSTEM wherever designed . possible . Dust generated from certain materials can 10 USE THE RIGHT TOOL . Do not force the tool or be hazardous to your health and in some cases , a attachment to do a job for which it is not designed . fire hazard . Always operate the power tool in a well 11 . WEAR PROPER APPAREL . DO NOT wear loose ventilated area with adequate dust removal . clothing , gloves , neckties , rings , bracelets or other 25 . ALWAYS WEAR EYE PROTECTION . Any power jewelry that may get caught in moving parts . tool can throw foreign objects into your eyes which Nonslip footwear is recommended . Wear protective could cause permanent eye damage . ALWAYS hair covering to contain long hair . wear safety goggles ( not glasses ) that comply with 12 . WEAR A FACE MASK OR DUST MASK . Sawing , ANSI safety standard Z87 . 1 . Everyday glasses cutting and sanding operations produce dust . have only impact resistant lenses . They ARE NOT safety glasses . NOTE : Glasses or goggles not in 13 . DISCONNECT TOOLS before servicing and when compliance with ANSI Z87 . 1 could cause serious changing accessories such as blades , cutters , etc . injury when they break . 14 . REDUCE THE RiSK OF UNiNTENTiONAL 26 . DiRECTiON OF FEED . Feed work into a blade or STARTING . Make sure the switch is in the OFF cutter against the direction of rotation of the blade or position before plugging into the power supply . cutter only . 15 . USE ONLY RECOMMENDED ACCESSORIES . 27 . DO NOT AUTHORZE ADDiTiONAL USERS to Consult the Operator's Manual for recommended operate this power tool without the accompanying accessories . The use of improper accessories may operators manual for which the user must read and cause injury to you or damage to the tool . adjusting understand . wrenches are removed from the tool before turning ON . 16 . REMOVE ADJUSTING KEYS AND WRENCHES . Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning ON .
Page: 4

12 . PROVIDE ADEQUATE SUPPORT to the rear ALWAYS USE SAW BLADE GUARD , splitter and anti - kickback pawls for every through - sawing and the sides of the saw table for long or wide operation . Through - sawing operations are those workpieces . in which the blade cuts completely through the 13 . workpiece when ripping or crosscutting . Always be AVOID KICKBACKS ( work thrown back towards sure blade guard is tightened securely . you ) by keeping the blade sharp , the rip fence parallel to the saw blade and by keeping the splitter , 2 . ALWAYS HOLD WORK FIRMLY against the miter anti - kickback pawls and guards in place , aligned gauge or rip fence . and functioning . Do not release work before passing it completely beyond the saw blade . Do not rip work 3 . ALWAYS USE a push stick , especially when ripping that is twisted , warped or does not have a straight narrow stock . Refer to ripping instructions in this edge to guide it along the fence . Do not attempt to Operator's Manual where the push stick is covered reverse out of a cut with the blade running . in detail . A pattern for making your own push stick is included on page 28 . 14 . AVOID AWKWARD OPERATIONS and hand positions where a sudden slip could cause your 4 . NEVER PERFORM ANY OPERATION hand to move into the saw blade . FREEHAND , which means using only your hands to support or guide the workpiece . Always use 15 . NEVER USE SOLVENTS to clean plastic parts . either the fence or the miter gauge to position Solvents could possibly dissolve or otherwise and guide the work , damage the material . Only a soft damp cloth should be used to clean plastic parts . I , _ k DANGER ] FREEHAND CUTTING iS THE MAJOR CAUSE OF 16 . MOUNT your table saw on a bench or stand KICKBACK AND FINGER / HAND AMPUTATIONS , before performing any cutting operations . Refer to NEVER USE THE MITER GAUGE AND FENCE ASSEMBLY on page 10 . SIMULTANEOUSLY , NEVER CUT METALS or materials that may make 5 . NEVER STAND or have any part of your body in 17 . hazardous dust . line with the path of the saw blade . Keep your hands out of the saw blade path . 18 . ALWAYS USE IN A WELL = VENTILATED AREA . 6 . NEVER REACH behind or over the cutting tool for Remove sawdust frequently . Clean out sawdust from the interior of the saw to prevent a potential fire any reason . hazard . 7 . REMOVE the rip fence when crosscutting . 19 . NEVER LEAVE THE SAW RUNNING 8 . DO NOT USE a molding head with this saw . UNATTENDED . Do not leave the saw until the blade comes to a complete stop . 9 . FEED WORK INTO THE BLADE against the direction of rotation only . 20 . FOR PROPER OPERATION follow the instructions in this Operator's Manual entitled OPERATION 10 . NEVER use the rip fence as a cut - off gauge when ( Page 17 ) . crosscutting . NOTE : On machines with no stand or if stand is not 11 . NEVER ATTEMPT TO FREE A STALLED SAW being used , a hole approximately 11 in . square must BLADE without first turning the saw OFF . Turn be cut under saw to allow sawdust to fall through . power switch OFF immediately to prevent motor Failure to cut this hole will allow sawdust to build damage . up in the motor area , resulting in a fire hazard and potential motor damage .
Page: 5

or a # 14 wire with a 15 A time - lag fuse . NOTE : When GROUNDING iNSTRUCTiONS using an extension cord on a circuit with a # 14 wire , the IN THE EVENT OF A MALFUNCTION OR extension cord must not exceed 25 feet in length . Before connecting the motor to the power line , make sure the BREAKDOWN , grounding provides a path of least resistance for electric currents and reduces the risk of switch is in the off position and the electric current is rated the same as the current stamped on the motor electric shock . This tool is equipped with an electrical nameplate . Running at a lower voltage will damage the cord that has an equipment - grounding conductor motor . This tool is intended for use on a circuit that has and a grounding plug . The plug must be plugged a receptacle like the one illustrated in Fig . 1 . into a matching receptacle that is properly installed and grounded in accordance with all local codes and ordinances . Fig . 1 shows a three - pronged electrical plug and receptacle that has a grounding conductor . If a properly DO NOT MODIFY THE PLUG PROVIDED . tf it will not grounded receptacle is not available , an adapter ( Fig . 2 ) can be used to temporarily connect this plug to a two - fit the receptacle , have the proper receptacle installed contact grounded receptacle . The adapter ( Fig . 2 ) has a by a qualified electrician . rigid lug extending from it that MUST be connected to a permanent earth ground , such as a properly grounded IMPROPER CONNECTION of the equipment grounding conductor can result in risk of electric shock . The receptacle box . conductor with the green insulation ( with or without CAUTION yellow stripes ) is the equipment grounding conductor . In all cases , make certain the receptacle is properly tf repair or replacement of the electrical cord or plug is grounded , if you are not sure , have a qualified necessary , do not connect the equipment grounding conductor to a live terminal . electrician check the receptacle . CAUTION CHECK with a qualified electrician or service person This tool is for indoor use only . Do not expose to if you do not completely understand the grounding rain or use in damp locations . instructions , or if you are not certain the tool is properly grounded . Fig . 1 Three - Pronged Plug USE only three - wire extension cords that have three - q7 pronged grounding plugs with three - pole receptacles that accept the tool's plug . Repair or replace damaged or worn cords immediately . _ 1 _ ) 1 Properly Grounded { _ _ . . g Prong GUIDELINES FOR EXTENSION CORDS Three - Pronged Receptacle USE THE PROPER EXTENSION CORD . Make sure Grounding Lug _ - # . . . . . . Fig . 2 your extension cord is in good condition . Use an / I _ ! Make sure this is extension cord heavy enough to carry the current your I _ . _ - _ connected to a product will draw . An undersized cord will cause a drop _ - [ _ . . _ , _ I known ground . - _ , in line voltage resulting in loss of power , _ . L _ _ _ Two - Pronged overheating and burning out of the motor . The table on the right shows the correct size to use depending on _ } 4 _ J Adapter - ' - _ Receptacle cord length and nameplate ampere rating , tf in doubt , use the next heavier gauge . The smaller the gauge CAUTION number , the heavier the cord . This tool must be grounded while in use to protect the operator from electric shock . Make sure your extension cord is properly wired and in ' O " • O'm ' good condition . Always replace a damaged extension ( When using 120volts only ) cord or have it repaired by a qualified technician before Ampere Rating Total length of Cord using it . Protect your extension cords from sharp MoreThan NotMoreThan 25ft . 50ft . 100ft . 150ft . objects , excessive heat and damp or wet areas . 0 6 8 16 16 14 6 10 8 I6 14 12 Use a separate electrical circuit for your tool . This circuit 10 12 6 16 14 12 must not be less than # 12 wire with a 20 A time - lag fuse
Page: 6

RECOMMENDED ACCESSORIES Separate all parts from packing materials . Check each part with the illustration on the next page and the " Table WARNIING of Loose Parts " to make certain all items are accounted Visit your Sears Hardware Department or see the for , before discarding any packing material . Craftsman Power and Hand Tools Catalog to purchase recommended accessories for this power tool . [ A WARNINIG IA WARNINGI To avoid the risk of personal injury : if any part is missing or damaged , do not attempt • Do not use adjustable ( wobble ) type dadoes or to assemble the table saw , plug in the power cord , carbide tipped dado blades . or turn the switch ON until the missing or damaged = Only use atackable dadoes . pert is obtained and is installed correctly . To avoid • Maximum dado width is 1 / 2 " . electric shock , use only identical replacement • Do not use a dado with a diameter larger than 6 " . parts when servicing double insulated tools . Call • Do not use molding head set with this saw . 1 = 800 = 4 - MY = HOME ® for replacement parts . • Do not modify this power tool or use accessories not recommended by Sears . TABLE OF LOOSE PARTS ITEM DESCRIPTION QUANTITY A Table saw assembly 1 B Rear table extension 1 C Rear table extension tube 2 NOT SUPPLIED SUPPLIED D Hardware bag assembly 1 E Blade guard and splitter assembly 1 F Hardware bag assembly 1 each Blade wrench G Handwheel 2 Medium screwdriver H Dome nut 2 t Rip fence 1 J Hex key 1 K Blade 1 # 2 Phillips screwdriver L Blade wrench 2 Blade wrench M Right extension wing table 1 N Miter gauge 1 [ II II II III II I O Hardware bag assembly 1 Straight edge P Left table extension 1 Q Upper tube 2 3 mm Hex key R Dust bag 1 STAND 1 S Floor plate Adjustable wrench T Stand door 1 U Stand base 1 NOTE : To make assembly easier , keep contents of box together . Apply a coat of automobile wax to the table . Combination square Wipe all parts thoroughly with a clean dry cloth . This will reduce friction when pushing the workpeice . To avoid injury , the styrofoam block should be removed between the motor and table .
Page: 7

UNPACKING YOUR TABLE SAW l . . . . J , Jl _ 1 B D A C \ J K L M N 0 P R T
Page: 8

Bladeguard Tableinsert Sidetableextensionwing MitergaugeX fence Extensiown inglockinglever Bladetiltscale Bevetliltinghandwheel Bladetiltpointer Bladebevellockknob Overloadresetswitch ON / OFFswitchwithsafetykey Bladeelevationhandwheel Ripfenceandmiter gaugestorage Toolsstorage
Page: 9

OVERLOADRESETSWITCH - Resetsthe ANTFKICKBACPKAWLS - fPreventtsheworkpiece thermocoupalendprovidesa wayto restartthesaw frombeingkickedupwardorbacktowardthefronto the motorif it overloadosroverheats . tablesawbythespinningblade . ARBOR - Theshaftonwhichthebladeordadois PUSHSTICK - Usedtopushworkpiecewshen performingrippingoperations . mounted . RESIN - A stickysapthathashardened . BEVELCUT - Ananglecutmadethroughthefaceof theworkpiece . REVOLUTIONPSERMINUTE ( RPM ) - Thenumberof turnscompletedbyaspinningobjectinoneminute . BLADEBEVELSCALE - Measuretsheangletheblade istiltedwhensetfora bevecl ut . RiPFENCE - A guideusedforripcuttingwhichallows theworkpiecetocutstraight . BLADEELEVATIONHANDWHEE - LRaisesand lowerstheblade . RiPPiNG - Cutting with the grain of the wood or along the length of the workpiece . BLADEGUARD - Clearplasticcoverthatpositions itselfoverthebladewhilecutting . SAW BLADE PATH - The area of the workpiece or table top directly in line with the travel of the blade or the COMPOUNCDUT - Asimultaneoubsevelandmiter part of the workpiece that will be cut . cut . SET - The distance between two saw blade tips , bent CROSSCUT - A cut made across the width of the outward in opposite directions to each other . The further workpiece . apart the tips are , the greater the set . DADO - Special cutting blades that are used to cut SPLITTER - Keeps the workpiece split apart after being grooves in a workpiece . cut to prevent binding on the blade and workpiece . FREEHAND - Performing a cut without using a rip TABLE iNSERT - Insert that is removed from the table fence , miter gauge , hold down or other proper device to to install / remove blades , tt is also removed for dado prevent the workpiece from twisting during the cutting cutting . When dado cutting , a dado insert plate must be operation . used . GUM - A sticky sap from wood products . THROUGH SAWING - Making a cut completely through the length or width of a workpiece . HEEL - Misalignment of the blade . WORKPIECE - Material to be cut . JAMB NUT - Nut used to lock another nut in place on a threaded rod or bolt . Saw blade path Leading edge KERF - The amount of material removed by the blade Kerf cut . Surface MITER CUT - An angle cut made across the width of the workpiece . Trailing edge MITER GAUGE - A guide used for crosscutting Workpiece operations that slides in the table top channels ( grooves ) located on either side of the blade , it helps make accurate straight or angle crosscuts .
Page: 10

ASSEMBUNGSTAND ( FIG . A ) INSTALUNG A SHELF ( NOT iNCLUDED ) ( FIG . A - 2 ) 1 . Unpackallpartsandgroupbytypeandsize . Refer NOTE : Attach shelf before assembling the floor plate . tothepartslistforcorrecqt uantities . 1 . Turn the stand upside down . 2 . Attachthestanddoor ( 3 ) tothefrontofthestand 2 . Rest the shelf board against the 4 shelf support fins located on the side of the cabinet . base ( 5 ) usingthreescrewsM5 " 12 - 12 ( 4 ) . 3 . Attachthefloorplate ( 1 ) tothestand ( 5 ) using 3 . Drill 4 apporpiately sized holes , two on each side , tenscrewsM5 " 12 - 12 ( 2 ) . SeePARTSLISTAND through the cabinet into the shelf endgrain . SCHEMATIFCORSTANDSECTION . 4 . Secure the shelf with four wood screws ( not NOTE : Ashelf ( notincluded ) canbeaddedtothe included ) . standbase ( seenextsectionpriorto installingthe 5 . Tighten the four wood screws . floorplate ( 1 ) ) . 4 . Tightenhardware . Fig . A - 2 1 5 . Placethestandona levelsurfaceandadjustthe rear - lefat djustablfeoot , sothestandiscontacting thefloor . Fig . A ASSEMBLE TABLE SAW TO STAND ( FIG . B ) 1 . Place the saw ( 6 ) on the stand ( 5 ) . 2 . Line up the four holes in saw base and stand ( 5 ) . 3 . Fasten saw to stand using four hex bolts ( 7 ) . 4 . Tighten all four hex bolts ( 7 ) . NOTE : DO NOT OVER TIGHTEN . THiS MAY DAMAGE THE SAW BASE . I , WARNINIG IF THE STAND WILL NOT BE USED , DO NOT OPERATE THE TABLE SAW ON THE FLOOR . THiS IS A VERY DANGEROUS POSiTiON . Fig . B SHELF CONSTRUCTION ( FIG . A - l ) • Use good quality plywood or solid wood • The shelf must be installed before the floor plate ( 1 ) ( Fig . A ) . Fig . A - 1 p , 22 - 1 / 2 in , _ J 83 " / , I3 / 4 t
Page: 11

MOUNTSAWONWORKSURFACE RIP FENCE ( FIG . D ) 1 . tfthestandwillnotbeused , thesawmustbe 1 . Lift upward on the rip fence handle ( 1 ) so the rear properlysecuredtoasturdyworkbencuhsingthe holding clamp ( 2 ) is fully extended . fourmountingholesat thebaseofthesaw . 2 . Place the rip fence on the saw table , and attach the 2 . Squarethesawonthemountingsurfaceandmark set plate ( 3 ) under the fence handle ( 1 ) to the rail first . thelocationofthefour3 / 8in.mountingholes . 3 . Drillthefour3 / 8in.holesintothemountingsurface . 3 . Push down on the fence handle ( 1 ) to lock . 4 . Placethesawontheworksurfacea , ndalignthe mountingholesofthesawwiththosedrilledthrough Fig . D thesurface . 5 . Fastenthesawtotheworksurface . Usinghardware suchas1 / 2in.lugboltswithwasher . [ A WAR " IN1G Do not operate this machine on the floor . This is very dangerous and may cause serious injury . [ A WARNINI G Always keep your work area clean , uncluttered and well lit . INSTALLING AND CHANGING THE BLADE BLADE RAISING HANDWHEEL ( FIG . C ) ( FIG . E , F , G ) 1 . Attach the up - down handwheel ( 1 ) to the elevation rod ( 2 ) at the front of the saw . Make sure the slots ( 3 ) I , _ WARNING I in the hub of the handwheel ( 1 ) engage with the pins * To avoid injury from an accidental start , make ( 4 ) . sure the switch is in the OFF position and the plug is not connected to the power source outlet . 2 . Attach and tighten the dome nut ( 5 - Fig . C - 1 ) . , , To avoid serious injury , the rear of the table insert must be level with the table . To adjust rear of Fig . C table insert , adjust the screw ( 3 ) in or out until the rear of the insert is level to or slightly above the table . To raise the insert , turn the screw counterclockwise , to lower the insert , turn the screw clockwise . NOTE : A rubber adjusting spacer ( 4 ) is provided under rear of insert for this purpose . 1 1 . Remove the table insert ( 1 ) by removing the two BLADE TILTING HANDWHEEL ( FIG . C = f ) screws ( 2 , 3 ) . Be careful not to lose the rubber 1 . Attach the bevel 0 ° - 45 ° handwheel ( 6 ) to the blade adjusting spacer ( 4 ) that is on the back screw ( 3 ) tilting rod on the right side of the saw in the same beneath the table insert ( Fig . E ) . manner as above . 2 . Attach and tighten the handwheel dome nut ( 5 ) . Fig . E Fig . C = 1 _ _ = = = = = = t { _ 3 8 - - - 2 / / 11
Page: 12

2 . Raisethebladearbor ( 4 - Fig . F ) tothemaximuml IA WARNIN ! G heightbyturningthebladeraisinghandwhee To avoid injury from a thrown workpiece , blade counterclockwise . parts , or blade contact , never operate saw without 3 . Placetheopen - endwrench ( 8 ) jawsontheflatsof . the proper insert in place . Use the original installed thesawarborto keepthearborfromturning ( Fig G ) insert for all through = sawing operations except dado andplacethebox - endwrench ( 9 ) onthearbornut cuts . A special dado insert plate must be installed ( 5 ) , andturncounterclockwise . when using a dado blade . 4 . Removethearbornut ( 5 ) andouterflange ( 6 - Fig . F ) . 5 . InstaltlhesawbladeontothearborwiththeBLADE BLADE GUARD ASSEMBLY ( FIG . H , I , J ) TEETHPOINTINGTOWARDTHEFRONTOFTHE 1 . Set the blade to maximum height and the tilt to zero SAW . degrees on the bevel scale with the hand wheels . 6 . Instaltlheflange ( 6 ) againstthebladeandthreadtheate Lock the blade bevel lock knob . arbornut ( 5 ) asfaraspossiblebyhand . Ensurethad 2 . Place the spring washer ( 2 ) , flat washer ( 3 ) , external thebladeisflushagainsttheinnersideof thebl tooth lock washer ( 4 ) onto the blade guard mounting flange . bolt ( 1 ) ( Fig . H ) . 3 . Insert bolt and washer assembly through splitter [ A WARNINI G bracket ( 5 ) . To avoid possible injury and damage to the workpiece , be sure to iNSTALL THE BLADE WiTH Fig . H THE TEETH POiNTiNG TOWARD THE FRONT OF TABLE in the direction of the rotation arrow on the blade guard . 5 4 J Blade guard _ Fig . F 4 7 6 5 1 and splitter ass'y 12 7 . To tighten the arbor nut , ( 5 ) place the open - end wrench ( 8 ) on the flats of the saw arbor to keep the 4 . Install the blade guard and splitter assembly ( 6 ) into arbor from turning ( Fig . G ) . the rear of the saw table . Thread the bolt ( 1 - Fig . H ) 8 . Place the box - end wrench ( 9 ) on the arbor nut ( 5 ) , into the internally threaded pivot rod ( 7 ) until snug . and turn clockwise ( to the rear of the saw table ) . 9 . Replace the blade insert in the table recess , insert Fig . I the screws through the front and rear holes and tighten remembering the rubber adjusting spacer ( 4 - Fig . E ) under the rear of the insert and leveling the rear of the insert to the table . Fig . G 8 - - 5 . Lift blade guard arm ( 8 ) up and using a straight edge , align the blade guard and splitter ass'y ( 9 ) with the saw blade ( 10 ) ( Fig . J ) . 6 . Shift the splitter bracket assembly to right or left until parallel alignment to the blade is achieved . 12
Page: 13

7 . Whenthesplitterisproperlyalignedwiththesaw INSTALLING TABLE SIDE EXTENSIONS ( FIG . L , L = I ) blade , tightentheboltsecurely . 1 . Identify the right hand table extension . NOTE : The splitter bracket must always be NOTE : For illustration purposes the view in Fig . L correctly aligned so the cut workpiece will pass looks " through " the saw table to the under side of the on either side without binding or twisting , table . The right hand table extension is the one with the measuring scale visible from the front of the saw [ A WARNIINa when it is installed to the right hand side of the saw table . See Fig . I - 1 flat washer ( 11 ) must be under knob ( 12 ) . NOTE : Be sure to tighten knob very tight and 2 . Unlock both front and rear cam locking levers ( 4 ) on periodically check tightness . the right hand side of the saw base by flipping the lever over . 3 . Insert the table extension mounting tubes ( 2 ) into the Fig , I - 1 two matching holes in the cam lever assemblies . NOTE : Make sure the front mounting tube has the measuring scale visible from the front of the saw . 4 . Slide the table extension toward the table until it rests against the saw table . 5 . Lock both cam locking levers by pushing them in toward the cam locking lever assemblies . AVOID KICKBACKS ( FIG . J ) 6 . tf the extension is not level to the table , adjust by ( Work thrown back towards you ) by keeping the blade inserting the spacers ( Carton Contents D ) between sharp , the rip fence parallel to the saw blade and by the extension and the tube it mounts onto . See page 17 . keeping the splitter , anti - kickback pawls and guards 7 . Make sure the screw ( 1 ) into the matching hole ( 2 ) in place , aligned and functioning . Do not release work of the extension mounting tube ( 3 ) . 8 . Install the left hand table extension the same manner before passing it completely beyond the saw blade . Do not rip work that is twisted , warped or does not have a NOTE : straight edge to guide it along the fence . Do not attempt • Make sure the screw ( 1 ) into the matching hole ( 2 ) to reverse out of a cut with the blade running . of the extension mounting tube ( 3 ) ( Fig . L - 1 ) . • For illustration purposes , the view in Fig . L looks [ , A WARNING I " through " the saw table to the under side of the table . Improper splitter alignment can cause " kickback " and serious injury . Fig , L Fig , J 8 10 Anti - kickback Pawl INSTALLING RIGHTSIDE TABLE EXTENSION WING 2 \ ( FIG . K ) 1 4 3 1 . Insert the two extension mounting tubes ( 3 ) into the side table extension wing ( 2 ) . NOTE : Make sure the front mounting tube has the Fig . L = I measuring scale visible from the front of the saw . 2 . Insert the screws ( 1 ) through the mounting tubes ( 3 ) into the side table extension wing ( 2 ) . 3 . Tighten the screws ( 1 ) . Fig . K z _ 2 3 13
Page: 14

5 . tf fence is loose when the handle is in the locked INSTALLING REAR TABLE EXTENSION ( FIG , M ) 1 . Place the rear table extension onto the two rear table ( downward ) position , do the following : extension tubes ( 1 ) . = Move the handle ( 2 ) upward and turn the adjusting nut ( 5 ) clockwise until the rear clamp is snug . 2 . Snap two long location seats ( 2 ) over the two rear = Over - tightening the adjusting screw will cause the table extension tubes ( 1 ) . Make sure the locating pin fence to come out of alignment . in the location seat fits into the matching hole ( 3 ) in the extension tube . 3 . Insert rear table extension tubes ( 1 ) into the two ] , _ WARNING I holes in the rear of the saw table and into extension Failure to properly align fence can cause " kickback " tube brackets under the table . Position rear table and serious injury . support so instruction labels are facing up . 4 . Snap one short location seat ( 4 ) over the end of the Fig , N left rear table extension tubes ( 1 ) . Make sure the locating pin in the location seat fits into the matching hole in the extension tube . Fig . M 5 4 2 7 RIP FENCE INDICATOR ADJUSTMENT ( FIG . N ) 1 . The rip fence indicator ( 6 ) points to the measurement scale . The scale shows the distance from the side of ADJUSTING REAR TABLE EXTENSION the fence to nearest side of the blade . 1 . Rear table extension should be positioned as close 2 . Measure the actual distance with a rule . tf there as possible to the rear of the table when ripping short is a difference between the measurement and the work pieces . indicator , adjust the indicator ( 6 ) . 2 . Rear table extension should be pulled out fully until 3 . Loosen the screw ( 7 ) and slide the indicator to the the location seat prevents it from moving outward correct measurement on the scale . Tighten the screw when ripping long work pieces that require extra and remeasure with the rule . support as you are completing the cut . RIP FENCE ADJUSTMENT ( FIG . N ) ] A WARNING ! 1 . The fence ( 1 ) is moved by lifting up on the handle ( 2 ) To avoid injury from an accidental start , make sure and sliding the fence to the desired location . Pushing the switch is in the OFF position and the plug is not down on the handle locks the fence in position . connected to the power source outlet . 2 . Position the fence on the right side of the table and along the edge miter gauge groove . ADJUSTING THE 90 ° ( 0 ° ) AND 45 ° POSITIVE STOPS 3 . Lock the fence handle . The fence should be parallel ( FIG . O , P , Q ) with the miter gauge groove . Your saw has positive stops that will quickly position the 4 . tf adjustment is needed to make the fence parallel to saw blade at 90 ° ( 0 ° ) to the table . Make adjustments the groove , do the following : only if necessary . = Loosen the two screws ( 3 ) and lift up on the handle ( 2 ) . = Hold the fence bracket ( 4 ) firmly against the front of the saw table . Move the fence until it is parallel with the miter gauge groove . • Push the handle down and tighten both screws . 14
Page: 15

90 ° ( 0 ° ) Stop 4 . Loosenthebladebevellockknob , turntheblade 1 . Disconnecthtesawfromthepowersource . tiltinghandwheetol movethebladeuntilit is45 ° to 2 . Turnthebladeelevationhandwheealndraisethe thetableandtightenthebladebevellockknob . bladetothemaximumelevation . 5 . Adjustthecollar ( 5 ) soitcontactsthebracke ( t3 ) whenthebladeis45 ° tothetable . Tightenthetwo 3 . Loosenthebladebevellockknob ( 1 ) andmovethe setscrews . bladetothemaximumverticapl ositiont , hentighten thelockknob ( 1 ) . 4 . Placeacombinatiosnquareonthetableandagainst BLADETiLTiNGPOINTER theblade ( 2 ) todetermineif thebladeis90 ° ( 0 ° ) to 1 . Whenthebladeispositioneadt90 ° ( 0 ° ) , adjustthe thetable . ( Fig . P ) bladetiltpointerto read0 ° onthescale . 5 . tfthebladeisnot90 ° ( 0 ° ) tothetable , loosenthetwo 2 . Loosenthemountingscrew , positionpointerover0 ° setscrews ( 4 ) , locatedonthecollar ( 5 ) underneath andtightenthescrew . thetablesaw ( Fig . Q ) withthehexkey ( Carton NOTE : Makeatrialcutonscrapwoodbeforemaking ContentsJ ) andbackoffthecollar . criticacl uts . Measureforexactness . 6 . Loosenthebevellockknob , turnthebladetilting handwheetol movethebladeuntilitis90 ° ( 0 ° ) tothe Fig . Q 4 tableandtightenthebevellockknob . 7 . Adjustthecollar ( 5 ) soitcontactsthebracke ( t3 ) whenthebladeis90 ° ( 0 ° ) tothetable . Tightenthe twosetscrews ( 4 ) ( Fig . Q ) . 450 Fig . O 90o 3 BLADEPARALLELTOTHEMITERGAUGEGROOVE ( FIG . R , S ) IA WARNIN ! G Fig . P This adjustment was made at the factory , but it should be rechecked and adjusted if necessary . 900 ( 0 ) 0 450 ] , A WARNING ] To prevent personal injury : = Always disconnect plug from the power source when making any adjustments . • This adjustment must be correct or accurate cuts can not be made . Also inaccurate adjustment can result in kickback and serious personal injury . 1 . Remove the safety switch key and unplug the saw . 2 . Remove the blade guard for this procedure but 45 ° Stop reinstall and realign after adjustment . 1 . Withthebladeintheupright90 ° ( 0 ° ) positionl , oosen 3 . Raise the blade to the highest position and set at the thebevellockknobandmovethebladetothe 0 ° angle ( 90 ° straight up ) . 4 . Select and mark , with a felt tip maker , a blade tooth maximumbevelangle . having a " right set " and rotate the blade so the 2 . Placethecombinatiosnquareonthetableasshown marked tooth is Y2in . above the table . inFig . Ptocheckif thebladeis45 ° tothetable . 5 . Place the combination square base ( 1 ) into the right 3 . tfthebladeisnot45 ° tothetable , loosenthetwoset side miter gauge groove ( 2 ) . ( Fig . R ) screws ( 4 ) , locatedonthecollar ( 5 ) underneatthhe 6 . Adjust the rule so it touches the front marked tooth tablesaw , ( Fig . Q ) withthehexkey ( CartonContents and lock ruler so it holds its position in the square J ) , andbackoffthecollar . assembly . 15
Page: 16

Fig . S 7 . Rotatethebladebringingthemarkedtoothtothe rearandaboutYzin . above the blade . 8 . Carefully slide the combination square to the rear until the ruler touches the marked tooth . 9 . tf the ruler touches the marked tooth at the front and rear position , no adjustment is needed at this time . tf not or the base of the rule is no longer parallel with the edge of the miter gauge groove , perform adjustment procedure described in next section . 2 3 1 4 Fig . R BLADE TILTING INDICATOR ( FIG . T ) , , _ , = = = = = = = = = = = = = = = = = = = = = = = = = = = = 1 . When the blade is positioned at 90 ° , adjust the blade tilt pointer to read 0 ° on the scale . j2 2 . Remove the magnifier , position the pointer over 0 ° 1 and replace the magnifier . Fig . T ADDITIONAL BLADE ADJUSTMENTS ( FIG . S ) NOTE : The adjusting lock nuts are 8 ram . The adjusting mechanism is located above the blade height adjusting hand wheel under the tabletop , tf the front and rear measurements are not the same . MITER GAUGE ADJUSTMENT ( FIG . T = I ) If the blade is partial to right aide : 1 . Loosen the lock handle ( 1 ) to allow miter body ( 2 ) to 1 . Loosen the two lock nuts ( 1 ) and turn the left rotate freely ( Fig . T - 1 ) . Position the miter body at adjustment screw ( 2 ) counterclockwise , then adjust 90 ° so the positive detent secures its position . the right side adjustment screw ( 3 ) clockwise . Tighten the lock handle to hold the miter body in 2 . Remeasure , as described in steps 4 to 9 in the position . prior section . 2 . tf the pointer ( 3 ) requires adjustment , loosen the 3 . When alignment is achieved , turn the left adjustment screw under the pointer with a hex key . Adjust the screw ( 2 ) until it touches the pivot rod ( 4 ) then tighten pointer to 90 ° on the scale then firmly tighten the both lock nuts ( 1 ) . adjustment screw . 3 . To change angles on miter gauge , loosen the lock if the blade is partial to left aide : handle ( 1 ) and rotate the miter body to desired angle 1 . Loosen the two lock nuts ( 1 ) and turn the right as indicated by the scale . Secure in position by adjustment screw ( 3 ) counterclockwise , then adjust tightening the lock handle . the left side adjustment screw ( 2 ) clockwise . 2 . Remeasure , as described in steps 4 to 9 in the Fig . T - 1 prior section . 3 . When alignment is achieved , turn the right adjustment screw ( 3 ) until it touches the pivot rod ( 4 ) 2 then tighten both lock nuts ( 1 ) . 1 3 16
Page: 17

OVERLOAD PROTECTION ( FIG . V ) BASICSAWOPERATIONS This saw has an overload relay button ( 3 ) that resets RAISETHEBLADE ( FIG . U ) the motor after it shuts off due to overloading or low To raise or lower the blade , turn the blade elevation voltage , tf the motor stops during operation , turn the ON handwheel ( 1 ) to the desired blade height , and then / OFF switch to the OFF position and unplug the saw . tighten lock handle ( 2 ) to maintain the desired blade Wait about five minutes for the motor to cool . Plug in the angle . saw , push in the reset button ( 3 ) and turn the switch to the ON position . Fig . U IA WARNINGI To avoid injury , the ON / OFF switch should be in the OFF position and the plug removed from the power source while the cool down takes place , to prevent accidental starting when the reset button is pushed . Overheating may be caused by misaligned parts or a dull blade or undersized extensing cord . TiLTiNG THE BLADE ( FIG . U ) inspect your saw for proper setup before using it 1 . To tilt the saw blade for bevel cutting , loosen the again . bevel lock knob ( 2 ) and turn the tilting handwheel ( 3 ) . 2 . Tighten the bevel lock knob ( 2 ) to secure . USING THE TABLE EXTENSION ( FIG . W , X ) tf the table extension is not parallel with the table , ON / OFF SWITCH ( FIG . V ) remove the bolts ( 1 ) and position the extension leveling The ON / OFF switch has a removable safety key . With spacers ( 2 ) between the table extension and tube until it the key removed from the switch , unauthorized and is parallel with the table , then tighten the bolts . hazardous use by children and others is minimized and NOTE : See page 6 for table of loose parts ITEM : D the saw will not turn on . Fig . W 1 . To turn the saw ON , insert key ( 1 ) into the slot in the switch ( 2 ) . Move the switch upward to the ON position . 2 . To turn the saw OFF , move the switch downward . 3 . To lock the switch in the OFF position , grasp the sides ( or yellow part ) of the switch toggle ( 1 ) , and pull it out . 4 . With the switch key removed , the switch will not 1 . Release the extension cam locking levers . operate . 2 . Slide the extension out until the correct measurement 5 . tf the switch key is removed while the saw is running , is displayed on the tube scale . The user sights the it can be turned OFF but cannot be restarted without scale off the edge of the table . re - inserting the switch key ( 1 ) . 3 . Tighten all extension lock handles . Fig . V Fig . X Right sidesca _ e of table e × tens _ on Left side scale of table extension 17
Page: 18

USINGTHE DUST CHUTE ( FIG . Y ) the fence and must not be warped , twisted , or bowed . Do not allow familiarity or frequent use of your IA WARNINI G table saw to cause careless mistakes . Remember To prevent fire hazard , clean and remove sawdust that even a careless fraction of a second is from under the saw frequently . enough to cause a severe injury . To prevent sawdust buildup inside the saw housing , 1 . Remove the miter gauge . Secure the rip fence to the attach a vacuum hose ( 1 ) to the dust chute ( 2 ) at the table at the desired rip measurement . rear of the table saw . Do not operate the saw with 2 . Raise the blade so it is about 1 / 8 in . higher than the the hose in place unless the vacuum is turned on . top of the workpiece . 3 . Place the workpiece fiat on the table and against Fig . Y the fence so the larger portion of the workpiece is between the blade and the fence . Keep the workpiece about 1 in . away from the blade . 4 . Turn the saw ON and wait for the blade to come up to speed . 5 . Slowly feed the workpiece into the blade . To feed workpiece into blade , only push against the back of the workpiece on the part ( 1 ) that will pass between the blade and the fence . Use a push stick at all times . CUTTING OPERATIONS la , WARNINI G AVOID KICKBACK To avoid kickback , only push There are two basic types of cuts : ripping and crosscutting . Ripping is cutting along the length and the against the back of the workpiece on the part ( 1 ) grain of the workpiece . Crosscutting is cutting either that will pass between the blade and fence . Use a across the width or across the grain of the workpiece . push stick at all times . Neither ripping nor crosscutting may be done safely freehand . Ripping requires the use of the rip fence , and Fig . AA crosscutting requires the miter gauge . NEVER USE THE TWO AT THE SAME TIME . [ A WARNI " IG Before using the saw each and every time , check the following : 1 . Blade is tight on the arbor . 2 . Bevel angle lock knob is tight . 3 . if ripping , fence knob is tight and fence is parallel to the miter gauge grooves . 4 . Blade guard is in place and working properly . 6 . Keep your thumbs off the table top . When your hand 5 . Safety glasses are being worn . reaches the front edge of the table ( 2 ) , finish the cut The failure to adhere to these common safety rules , with a push stick ( 3 ) ( Fig . BB ) . You can make a push and other printed within this manual , can stick using the pattern on page 28 . greatly increase the likelihood of injury . 7 . The push stick ( 3 ) should always be used for any ripping operations . ( Fig . BB ) RIPPING ( FIG . AA , BB ) 8 . Continue pushing the workpiece with the push stick ( 3 ) until it passes the blade guard and clears the [ A WARNINGI rear of the table . To prevent serious injury : • Never use the miter gauge when ripping . = Never use more than one rip fence during a single cut . = Keep both hands away from the blade and path of the blade . • The workpiece must have a straight edge against 18
Page: 19

Never attempt to pull the workpiece backwards [ _ , WARNING I during a cutting operation . This will cause Never attempt to pull the workpiece backwards kickback and serious injury to the user can during a cutting operation , This will cause Occur , kickback and serious injury to the user can occur , When the blade completely stops raise the 1 . Remove the rip fence and place the miter gauge a anti - kickback pawls ( 4 ) on each side of the splitter miter gauge groove on the table . and slide the workpiece out , 2 . Adjust the blade height so it is 1 / 8 in . higher than the top of the workpiece . Fig , BB 3 . Hold the workpiece firmly against the miter gauge with the blade path in line with the desired cut 4 location . Move the workpiece to one inch distance from the blade . 4 . Start the saw and wait for the blade ( 1 ) to come up to full speed . Never stand directly in line of the saw blade path , but always stand to the side of the blade 1 that you are cutting on . 5 . Keep the workpiece ( 2 ) against the face of the miter gauge ( 3 ) and flat against the table . Then slowly push the workpiece through the blade . BEVEL RIPPING 6 . Do not try to pull the workpiece back with the blade This cut is the same as a rip cut except the blade bevel turning . Turn the switch OFF , and carefully slide the angle is set to an angle other than " 0 " . workpiece out when the blade is completely stopped . [ _ , WARNING i I A , WARNING ! Cut only with the workpiece and the fence on the Always position the larger surface of the workpiece right side of the blade . on the table when crosscutting and / or bevel crosscutting to avoid instability . RiPPiNG SMALL PIECES Fig , CC 1 [ A WARNINGI Avoid injury from the blade contact . Never make through = saw cuts narrower than 3 / 4 in . wide . 1 . it is unsafe to rip small pieces , instead , rip a larger piece to obtain the size of the desired piece . 2 . When a small width is to be ripped , your hand cannot u be safely put between the blade and the rip fence , therefore , use one or more push sticks to pass the workpiece completely through and past the blade . BEVEL CROSSCUTTING ( FIG . DD ) 0o ~ 45 ° BLADE BEVEL & 90 ° MITER ANGLE CROSSCUTTING 90 ° MITER ANGLE ( FIG . CC ) This cutting operation is the same as crosscutting except the blade is at a bevel angle other than 0 ° [ _ , WARNING I To prevent serious injury : I , A WARNING I = Do not allow familiarity or frequent use of your Always work to the right side of the blade during table saw to cause careless mistakes , Remember this type of cut . The miter gauge must be in the right that even a careless fraction of a second is side groove because the bevel angle may cause the enough to cause a severe injury , blade guard to interfere with the cut if used on the • Keep both hands away from the blade and the left side groove . path of the blade . 19
Page: 20

MiTERiNG 0o - 45 ° MITER ANGLE ( FIG . FF ) 1 . Adjusttheblade ( 1 ) tothedesiredangle , andtighten thebladebevellockknob . This sawing operation is the same as crosscutting except the miter gauge is locked at an angle other 2 . Tightenmiterlockhandle ( 2 ) at 90 ° . than 90 ° . 3 . Hold workpiece firmly against the face of the miter gauge throughout the cutting operation . 1 . Set the blade ( 1 ) to 0 ° bevel angle and tighten the blade bevel lock knob . Fig , DD 2 . Set the miter gauge ( 3 ) at the desired miter angle and lock in position by tightening the miter gauge locking handle . 3 . Hold the workpiece ( 2 ) firmly against the face of the miter gauge throughout the cutting operation . Fig . FF COMPOUND MITER CROSSCUTTING ( FIG . EL ) 0o - 45 ° BLADE BEVEL & 0o - 45 ° MITER ANGLE This sawing operation is combining a miter angle with a bevel angle . [ 4 WARNINI G 14 WARNIN ! e Always work to the right side of the blade during ABRASIVE AND METAL CUTTING BLADES MUST this type of cut . The miter gauge must be in the right NOT BE USED WiTH THiS SAW side groove because the bevel angle may cause the This saw was not made to cut metals or masonry blade guard to interfere with the cut if used on the materials . Doing so may result in injury , tt will also void left side groove . the warranty . 1 . Set the miter gauge ( 3 ) to the desired angle . USING WOOD FACING ON THE RiP FENCE 2 . Place the miter gauge in the right side groove of ( FIG . GG ) the table . When performing some special cutting operations , you can add a wood facing ( 1 ) to either side of the rip 3 . Set the blade ( 1 ) bevel to the desired bevel angle fence ( 2 ) . and tighten the blade bevel lock knob . NOTE : Before using wood facing on the rip fence , 4 . Hold workpiece firmly against the face of the miter make sure the auxiliary fences are lowered flush to the gauge throughout the cutting operation . table top . 1 . Use a smooth straight 3 / 4 in . thick wood board ( 1 ) Fig . EE that is as long as the rip fence . 2 . Attach the wood facing to the fence with wood I 3 screws ( 3 ) through the hole in the fence . A wood fence should be used when ripping material such as thin paneling to prevent the material from catching between the bottom of the fence and the table . 3 Fig . GG 2 1 2O
Page: 21

DADOCUTS ( FIG . HH ) • Only Stackable dado blades can be used on this saw . • DO NOT use Adjustable or Wobble type dadoes . • Maximum dado cut width is Y2in . 1 . A dado table insert must be purchased separately for this saw to accept a dado blade . Remove saw blade and blade guard for dado cuts ONLY . Reinstall and realign blade guard for all through - sawing operations . Install a dado not exceeding 6 in . in diameter and Y2 in . in width 2 . Install the dado table insert making sure the rear of the insert is flush with the table . A rubber adjusting spacer is provided under the rear of the insert for this purpose . 3 . Instruction for operating the dado is packed with the separately purchased dado set . 4 . The arbor ( 1 ) on this saw restricts the maximum width of the cut to Y2in . 5 . tt is not necessary to install the outside flange ( 2 ) before threading on the arbor nut ( 3 ) for maximum Y2in . dado cuts . Make sure that the arbor nut ( 3 ) is tight , and that at least one thread of the arbor sticks out past the nut . 6 . Use only the correct number of round outside blades and inside chippers as shown in the dado set's instruction manual . Blade / chippers must not exceed F2in . total in width . 7 . Check saw to ensure that the dado will not strike the housing , insert , or motor when in operation . [ _ WARNINIG For your own safety , always replace the blade , blade guard assembly , and doda insert when you are finished with the dado operation . You must also realign the blade guard assembly . Fig . HH - - - - 1 I | 111
Page: 22

MAiNTAiNING YOUR TABLE SAW Fig . FF GENERAL MAINTENANCE [ A WARNINI G Before maintaining or lubricating the saw , turn switch off , remove the switch key , and unplug the 1 SaW . 1 . Clean out all sawdust that has accumulated inside the saw cabinet and the motor . 2 . Polish the saw table with an automotive wax to keep it clean and to make it easier to slide the workpiece . 3 . Clean cutting blades with pitch and gum remover . 4 . Immediately replace a worn , cut , or damaged power You can place a small amount of dry lubricant on cord . bevel angle adjustment rod also . This rod ( 1 ) must be kept clean and free of sawdust , gum , pitch , and other WARNINI G contaminants for smooth operation . All electrical or mechanical repairs should be attempted only by a trained repair technician . tf excessive looseness is observed in any parts of the Contact the nearest Sears Service Center for blade raising mechanism or tilting mechanism , take the service . Use only identical replacement parts . Any complete unit to a Sears Service Center . other parts may create a hazard . 5 . Use liquid dish washing detergent and water to clean LUBRICATION all plastic parts . All motor bearings are permanently lubricated at the NOTE : Certain cleaning chemicals can damage factory and require no additional lubrication . plastic parts . On all mechanical parts of your table saw where a pivot 6 . Avoid use of the following cleaning chemicals or or threaded rod are present , lubricate using graphite or solvents : ammonia and household detergents silicone . These dry lubricants will not hold sawdust as containing ammonia . would oil or grease . BLADE RAiSiNG AND TiLTiNG MECHANISM ( FIG . FF ) After each five full hours of operation , the blade raising mechanism and tilting mechanism should be checked for looseness , binding , or other abnormalities . With the saw disconnected from the power source , turn the saw upside down and alternately pull upward and downward on the motor unit . Observe any movement of the motor mounting mechanism . Adjusted looseness or play in the blade raising screw ( 1 ) ( Fig . FF ) . As follows : 1 . Using a 14 mm wrench , loosen the check - nut ( 2 ) . 2 . Adjust nut ( 3 ) until it is finger - tight against the bracket ( 4 ) , and then back off the nut ( 3 ) 1 / 6 turn . 3 . Tighten nut ( 2 ) with a second 14 mm wrench , while holding nut ( 3 ) with the first wrench in place . Maximum allowable play of screw rod ( 1 ) is 0.16 in . ( 4 ram ) . 22
Page: 23

[ A WARNINI O To avoid injury from an accidental start , turn the switch OFF remove the switch key and always remove the plug from the power source before making any adjustments , = If for any reason the motor will not run , contact Sears Service Center at f = 800 = 4 - MY = HOME ® , SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION Saw will not start . 1 . Saw not plugged in . 1 . Plug in saw . 2 . Fuse blown or circuit breaker tripped . 2 . Replace fuse or reset circuit breaker . 3 . Cord damaged . 3 . Replace power cord . 4 . Debris in on / off switch 4 . Unplug and remove switch from saw . Separate switch in half and clean any debris within . Does not make accurate 45 ° 1 . Positive stop not adjusted correctly . 1 . Check blade with square and adjust and 90 ° rip cuts . positive stop . 2 . Tilt angle pointer not set accurately . 2 . Check blade with square and adjust to zero . Material pinched blade when 1 . Rip fence not aligned with blade . 1 . Check and align rip fence and blade ripping . 2 . Warped wood , edge against fence is to miter gauge groove . not straight . 2 . Select another piece of wood . Material binds on splitter . 1 . Splitter not aligned correctly with blade . 1 . Check and align splitter with blade . 1 . Dull blade . Saw makes unsatisfactory 1 . Replace blade . cuts . 2 . Blade mounted backwards . 2 . Turn the blade around . 3 . Remove blade and clean with 3 . Gum or pitch on blade . 4 . Incorrect blade for work being done . turpentine and coarse steel wool . 5 . Gum or pitch on blade causing erratic 4 . Change the blade . feed . 5 . Remove blade and clean table with turpentine and steel wool . Material kicked back from 1 . Rip fence out of adjustment . 1 . Align rip fence with miter gauge blade . 2 . Splitter not aligned with blade . groove . 3 . Feeding stock without rip fence . 2 . Align splitter with blade . 4 . Splitter not in place . 3 . Install and use rip fence . 5 . Dull blade . 4 . Install and use splitter . ( with guard ) 6 . The operator letting go of material 5 . Replace blade . before it is past saw blade . 6 . Push material all the way past saw 7 . Miter angle lock knob is not tight . blade before releasing work . 7 . Tighten knob . Blade does not raise or tilt 1 . Sawdust and dirt in elevation / tilting 1 . Brush or blow out loose dust and dirt . freely , mechanisms . Blade does not come up to 1 . Extension cord too light or too long . 1 . Replace with adequate size cord . speed . Reset trips too easily . 2 . Low house voltage . 2 . Contact your electric company . Machine vibrates excessively . 1 . Saw not mounted securely to 1 . Tighten all mounting hardware . workbench . 2 . Reposition on flat level surface . 2 . Bench on uneven floor . 3 . Replace blade . 3 . Damaged saw blade . Does not make accurate 45 ° 1 . Miter gauge out of adjustment . 1 . Adjust miter gauge . and 90 ° crosscuts .
Page: 24

10 in . TABLE SAW MODEL NO . 137.248850 [ A WARNINI G When servicing use only CRAFTSMAN replacement parts , Use of any other parts many create a HAZARD or cause product damage , Any attempt to repair or replace electrical parts on this Table Saw may create a HAZARD unless repair is done by a qualified service technician . Repair service is available at your nearest Sears Service Center , PARTS LiST FOR TABLE SAW SCHEIV1ATIC QTY I . D . Description Size QTY LD , Description Size 08VH CORD CLAMP 0KMS HEX NUT M6 0T 5 09JK WRENCH 0KMY HEX . NUT M8 25T 65 0B23 SADDLE 0KQJ CROWN NUT M8 25T 125 0B24 SPRING 0KRX HEXAGON NUT AND FLAT WASHER M6 _ 0 0B27 POINTER BRACKET 0KSW STRAIN RELIFF 0B2B NEEDLE POINTER 0LS CIRCUIT BREAKER SWITCH 0B2E SWFCH BOX 0SZY SLID NG BASE ASS'Y 0B3H INSERT # 23 0SZZ SLID NG BASE ASS'Y 0B3R WRENCH 0WFV KNOB 0BBA WARNING STICK LABE 118N CR RE PAN HD SCREW M6 0 55 0B99 SPACER 20WQ HEX HD BOLT M6 * 0 50 0B9C PLUNGFR HOUSING 2149 KNOB 0B9P CLAMP 23PP BLAD F 0BA4 SPACER 275F LOCAT ON SEAT 0BA9 SPACER 275R LOCAF ON SEAT 0BAA CLAMP 275U SPACER 0BAB SHIM 27A ROCKER SWITCH 0BAC S _ T NUT 27A2 SWITCH KEY 0BAF ARBOR COLLAR 28CY HAND WHEE ASSY 0BAU SUPPORTING PLATE 28CZ HAND WHEEL ASSY 0BC2 LOCATION SPAT 29PD WARNING LABEL 0BPA LOCK KNOB 29R2 WARNING LABEL 0J3U HEX WRENCH 2BYT HEX NUT 2BYZ BRACKET 0J4F FLAT WASHER @ 8 " 16 25 2EPP MOTOR 0J4H FLAT WASHER @ 030 02 0J4M FLAT WASHER ( p 2 _ 21 I 2ERP HEIGHT REGULATING BOLT ASS'Y 2EST EXTENTION WING 0J5L FLAT WASHER ( p5 " 10 03 10 2ESU EXTENTION WING # AW 0J6T FLAT WASHER 3 / 163 / 4 1 / 16 4 2ESV TABLE # AW 0J6U FLAT WASHER 3 / 161 / 2 3 / 64 1 2ESW COVER 0J6V FLAT WASHER 3 / 163 / 8 0022 8 0J70 FLAT WASHER 1 / 4 " 3 / 4 7 / 64 2 2ESX NEEDL E POINTER 0J76 FLAT WASHER 1 / 4 " 3 / 4 1 / 1B 2 2ESZ SPECIAL BOLT 0J78 FLAT WASHER 1 / 4 " 1 / 2 3 / 32 1 2ET2 EXTENTION WING # AW 0J8D FLAT WASHER 3 / 83 / 4 5 / 64 2 2ET4 UPPER TUBE 2ET5 UPPER TUBE 0J95 SPRING WASHER ( p6 1 2ET6 BODY SHEL 0JAA WASHFR 98 1 2ET9 ANGLE ROD 0JAE EXTERNAL TOOTH LOCK WASHER @ 4 2 2ETB ROLLING WHEE 0JAF EXTERNAL TOOTH LOCK WASHER @ 5 1 0JED C RING 1 2ETE PLASTIC GUARD 0JP9 HEX HD BOLT M5 * 0B 12 2 2ETG UPPER TUBE 0JXL HEX SOC SET SCREW M10 " 1 5 12 1 2ETJ UPPER TUBE 0KOZ HEX HD SCREW AND WASHER M8 " 1 25 1B 4 2ETK UPPER TUBE 0K15 HEX HD SCREW AND WASHER M6 _ 1 0 20 3 2ETL DUST BAG 0K16 HEX HD SCREW AND WASHER M8 " 1 25 1B 1 2ETU SCALE 0K25 HEX SOCKET HDCAP SCREW M5 " 08 20 1 2ETV SCALE 0K3G CR RE PAN HD SCRFW & WASHER M5 " 08 12 1 2ETW SCALE 0K57 CR RE COUNT HD SCRFW M5 " 08 1B 1 2ETX SCALE 0K7F CR RE ROUND WASHER HD SCREW M5 " 08 8 2 2ETY SCALE 0K7H CR RE ROUND WASHER HD SCREW M5 " 08 25 8 2ETZ LABEL 0K7K CR RE ROUND WASHER HD SCREW M6 _ 1 0 12 2 2EVG RIP FENCE ASS'Y 0K8C CR RECOUNT HD TAPPING SCREW M4 " 18 10 6 2EVJ MITER GAUG E ASS'Y 0K9T HEX HD TAPP NG SCREW M5 " 1B 1B 6 2EV SLID NG BASE ASS'Y 0K9U HEX HD TAPPNG SCRFW M5 " 1B 25 4 2EW3 BLADF GUARD ASS'Y 0KA4 CR RE PAN HD TAPPING SCREW M4 " 1B 1B 2 2F6F RETA NING CLIP 0KAP CR RE PAN HD TAPPING SCREW M5 " 08 10 1 2F6U COLLAR 0KC8 CR RE TRUSS HD TAPPING SCREW M41B 1B 2 2F9E INSTRUCTIONS MANUAL 0KCA CR RE TRUSS HD TAPPING SCREW M5 " 12 12 2 2FLK LEAD WiRE ASSY 0KCH CR RE PAN HFAD TAPPING & WASHER SCRFW M5 " 08 12 2 2FST POWER CABLE ASS'Y 0KCX CR RE PAN HD PLAIN WASHER TAPPING SCREW M5 " 08 10 6 2GBJ CR RE PAN HD SCREW M5 " 08 2 0KCY CR RE PAN HD PLAIN WASHER TAPPING SCREW M5 " 08 12 8 2GHL RETA NING CLIP 0KDR CR RE PAN HD SCRFW M5 " 08 10 1 2G J9 SPACER 0KFB CR RE PAN HD SCRFW M4 " 07 8 2 2GK F BRACKET GROUP ASS'Y 0KHZ CAP HD SQ NECK BOLT M6 " 1 0 12 2 2GRU BEVEL ANGL E ADJUSTMENT ASS'Y 0K J2 CAP HD SQ NECK BOLT M6 " 1 0 25 1 2GYV SLID NG BASE ASS'Y 0K J4 CAP HD SQ NECK BOLT M6 " 1 0 35 1 2H4C PULEY ASS'Y 0K J5 CAP HD . SQ NECK BOLT M6 _ 1 0 80 1 2H4D MOVAB E COVER ASS'Y 0KMR HEX NUT M5 _ 08 F 4 1 2H4E FRONT COVER ASS'Y
Page: 25

10 in . TABLE SAW MODEL NO . 137.248850 / SCHEMATIC / 2EST 2ETJ 2ETV 2ET4 2ET2 / / 2GRU , 0J76 / ODPA < / ZGKE 0JED _ KOZ4 0BAU / _ 0KMR \ - - / OKRX OKSG
Page: 26

10 in . TABLE SAW MODEL NO . 137.248850 PARTS LiST AND SCHEMATIC FOR MOTOR Size QTY I . D . Descirpfion 0HV8 BALL BEARING 6201Z LU 1 0HVU BALL BEARING 6200ZZ 1 0HX9 NEEDLE BEARING HK - 1010 1 0JAL EXT . TOOTH LOCK WASHER 4 cp4 0JX3 HEX . SOC . SETSCREW M5 " 0.8 - 8 2 0K3A CR . RE . PAN HD . SCREW & WASHER M5 " 0.8 - 30 4 0K5V CR . - RE . COUND . HD . SCREW M4 " 0.7 - 8 4 0KCP CR . RE . PAN HEAD TAPPING & WASHER SCREW M5 . 12 - 60 2 0KTH STRAIN RELIEF 1 0QEC ARBOR SHAFT ASS'Y 1 0QM2 BRUSH HOLDER ASS'Y 2 0QQT BRUSH ASS'Y 2 2 0QR0 BRUSH COVER 0R1Q MOTOR HOUSING 1 0R1S BEARING BUSHING 1 0R1Y ARMATURE ASS'Y 1 0R20 BAFFLE 1 28TR RETAINING CLIP 1 2DY4 BRACKET 1 1 2EQS MOTOR NAMEPLATE 2FLP FIELD ASS ' Y 1 0HgV OHV8 OR20 2FLP ORIS / ! \ ORIQ \ \ \ OH _ OqEC / _ \ \
Page: 27

10 in . TABLE SAW MODEL NO . 137.248850 PARTS LiST AND SCHEMATIC FOR STAND LB . QTY Description SIZE 0J68 3 FLAT WASHER cp5 _ 10 - 1 0K82 CR . RE . COUNT HD . TAPPING SCREW M5 " 12 - 16 3 0KB3 CR . RE . PAN HD . TAPPING SCREW M4 " 18 - 8 2 0KBA CR . RE . PAN HD . TAPPING SCREW M5 " 16 - 12 3 0KMS HEX . NUT M6 " 1.0 T = 5 1 0KMY HEX . NUT M8 " 1.25 T = 6.5 1 0KRL U - TYPE NUT 3 0VJX HEX . HD . SCREW AND WASHER M8 " 1.25 - 30 4 27CC CR . RE . PAN HD . TAPPING SCREW M5 " 16 - 6 2 2ETN BOTTOM BRACKET DOOR 1 2ETP FLOOR PLATE 1 2ETQ PLUNGER HOUSING 1 2ETR BOTTOM BRACKET 1 2ETS CUSHION 3 2ETT SETPLATE 1 2EU3 LEVELING PAD 1 2EU4 LEVELING WASHER 1 2EW0 HARDWARE BAG ASS'Y 1 2FS2 CR . RE . TRUSS HD . TAPPING SCREW M5 " 12 - 12 13 2FYJ PLUNGER 1 2FYK HINGE 1 2FYL PiN 1 2FYN PLATE CLAMP 1 OVJX 4 2ETR _ FYL OKMS 2FYN OKMY
Page: 28

PUSH STICK CONSTRUCTION This is a full - size drawing ( actual size ) Use good quality plywood or solid wood Use 1 / 2 in . or 3 / 4 in . material Push stick MUST be thinner than the width / of material being cut Z / / Drill Hole For Hanging / / Notch To Prevent Hand From Slipping Cut Here To Push 1 / 2 in . Wood Cut Here To Push 3 / 4 in . Wood r
Page: 29

Your Home For repair - in your home - of all major brand appliances , lawn and garden equipment , or heating and cooling systems , no matter who made it , no matter who sold itt For the replacement parts , accessories and owner's manuals that you need to do - it - yourself . For Sears professional installation of home appliances and items like garage door openers and water heaters . 1 - 800 - 4 - 1VlY - HOIVlE ® ( 1 = 800 = 469 = 4663 ) Call anytime , day or night ( U . S . A . and Canada ) www . sesrs . oorn www . sesrs . c8 Our Home For repair of carry - in items like vacuums , lawn equipment , and electronics , call or go on - line for the location of your nearest Sears Parts & Repair Center . 1 - 800 = 488 - 1222 Call anytime , day or night ( U . S . A . only ) www . sears . oorn To purchase a protection agreement ( U . S . A . ) or maintenance agreement ( Canada ) on a product serviced by Sears : 1 - 800 - 827 - 6655 ( U . S . A . ) 1 - 800 - 361 - 6665 ( Canada ) Para pedir servicio de reparaci6n Au Canada pour service en frangais : I = 800 = LE = FOYER " ° a domicilio , y para ordenar piezas : l = 888 - SU = HOGAR _ ' ( 1 - 800 - 533 - 6937 ) www . sears . ca ( 1 - 888 - 784 - 6427 ) TM M ® Registered Trademark / Trademark / s Service Mark of Sears Brands , LLC TM Ms ® Marca Registrada / Marca de Fb . brica / Marca de Servicio de Sears Brands , LLC MD McMarque de commerce / Marque deposee de Sears Brands , LLC © Sears Brands , LLC
Search in Table Saw on ebay
"