Home | Register Login | Wanted Manuals | MarketPlace | Members Area | Manuals Manufacturer Directory | UPC Lookup | Information Pages | Policy


Back To Craftsman Garage Door Opener       Model: 139.53675SRT2 or 13953675SRT2 Craftsman 1/2 HP Garage Door Opener
Regular Text Search or Search by Model Number

Register / log-in to add to your Hammerwall Collection.
Manual Location


This is a partial text extraction from the pdf, to download the pdf, click the Manual tab. If you want to search this text, hold control and F, and type the word you are looking for.

Page: 1

Owner's Manual Model No . 139.53662SRT2 139.53670SRT1 139.53675SRT2 For Residential Use Only CRRFTSMRN GARAGE DOOR OPENER 1 / 2 HP [ ] Safety Precautions Caution : [ ] Assembly Read and follow all [ ] Installation safety rules and [ ] Adjustment operating instructions before first use of this [ ] Care and Maintenance product . [ ] Operation [ ] Troubleshooting Fasten the manual [ ] Parts List near the garage door after installation . Complies with UL 325 fllll _ regulations effective January 1 , 1993 Sears , Roebuck and Co . , Hoffman Estates , IL 60179 U . S . A .
Page: 2

Contents Page Contents Page A review of safety alert symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Install the lights and lenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 You'll need tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Attach emergency release rope and handle . . . . . . . . . . . 19 Safety information regarding garage door Electrical requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 locks and ropes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety reversing sensor information . . . . . . . . . . . . . . . . . . . . . . . . 21 Testing your garage door for sticking , Install the safety reversing sensor . . . . . . . . . . . . . . . . . . . . . 22 , 23 binding and balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Fasten door bracket ( sectional door ) . . . . . . . . . . . . . . . . . . . . . . . 24 Illustration of sectional door installation . . . . . . . . . . . . . . . . . . . . . 4 Fasten door bracket ( one - piece door ) . . . . . . . . . . . . . . . . . . . . . 25 Illustration of one - piece door installation . . . . . . . . . . . . . . . . . . . . 5 Connect door arm to trolley ( sectional door ) . . . . . . . . . . . 26 Carton inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Connect door arm to trolley ( one - piece door ) . . . . . . . . . . 27 Hardware inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Adjustment section - pages 28 - 30 Assembly section - pages 8 - 11 Travel limit adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Assemble T - rail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Force adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Attach cable pulley bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Test the safety reversing sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Install trolley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Test the safety reverse system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Fasten T - rail to opener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Operation safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Install chain / cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Care of your opener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Attach sprocket cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Maintenance schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Tighten the chain and cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Operation of your opener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Installation section - pages 11 - 27 Receiver and remote control programming . . . . . . . . . . . . . . . 33 Installation safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Having a problem ? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 , 35 Determine header bracket location Repair parts , rail assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Sectional door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Repair parts , installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 One - piece door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Repair parts , opener assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Install the header bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Attach the T - rail to header bracket . . . . . . . . . . . . . . . . . . . . . . . . . 15 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Position the opener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 How to order repair parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Hang the opener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Maintenance agreement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Install the door control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Start by Reviewing these Important Safety Alert Symbols When you see these Safety Symbols on the following pages , they will alert you to the possibility of serious injury or death if you do not comply with the corresponding instructions . The hazard may come from something mechanical or from electric shock . Read the instructions carefully . Mechanical Electrical When you see this Safety Symbol on the following pages , it will alert you to the possibility of damage to your garage door and / or the garage door opener if you do not comply with the corresponding instructions . Read the instructions carefully . This garage door opener is designed and tested to offer safe service provided it is installed , operated , maintained and tested in strict accordance with the safety instructions contained in this manual .
Page: 3

You'll Need Tools During assembly , installation and adjustment of the opener , instructions will call for hand tools shown below . Pencil _ oooo o I _ Level Hack Saw Tape Measure Wire Cutters Ctaw Hammer _ 3 / 16 " , 5 / 16 " and 5 / 32 " DritI Bits = = 0 07 ) Stepladder ts Screwdriver Adjustable End Wrench An unbalanced garage door might not reverse To avoid damage to the garage door and when required and someone under the door opener , disable locks before installing and could be seriously injured or killed . operating the opener . Use a wood screw or nail to hold locks in the " open " ( unlocked ) If your garage door binds , sticks or is out of position . balance , call for professional garage door service . Garage doors , door springs , cables , Operation at other than 120V 60 Hz will cause pulleys , brackets and their hardware are under opener malfunction and damage . extreme tension and can cause serious injury or death . Do not try to loosen , move or adjust them yourself ! Ropes left on a garage door could cause Before you begin , complete the following test to someone to become entangled and killed . make sure your door is balanced , and is not Remove all ropes connected to the door before sticking or binding : installing and operating the opener . • Lift the door about halfway as shown . Release the door . It should stay in place , supported entirely by its springs . Identify the type and height of your door and any special conditions that exist and any additional • Raise and lower the door to see if there is any materials that may be required by referring to the lists binding or sticking . on page 4 or page 5 . ONE - PIECE DOOR
Page: 4

Before you begin , survey your garage area to see whether any of the conditions below apply FINISHED CEILING to your installation . Support bracket & fastening hardware is required . Horizontal and vertical reinforcement See page 17 is needed for lightweight garage doors Slack in Chain Tension ( fiberglass , steel , aluminum , door is Normal When with glass panels , etc ) . See page 24 for detaits . Garage Door is Ctosed Header Walt Extension Spring OR Access Door " _ Torsion Spring 0 Safety Sensor Ftoor must be level across width of door Safety Reversing Sensor Header Cable Pulley Closed Position B [ acket f Bracket / ' _ Trolley Rail Assembly Based on your particular requirements , there are , , / _ Cable I J several installation steps which might call for materials and / or hardware not included in the carton . • Step 1 , page 12 - Look at the wall or ceiling above ' _ O _ Y " Door / / the garage door . The header bracket must be Spring / / EmRorgen _ YRae _ as e securely fastened to structural supports . / i ; J Straight P • Step 5 , page 17 - Do you have a finished ceiling in / _ / Door your garage ? If so , a support bracket and additional fastening hardware may be required . , _ / _ Curved LJ _ Doocr • Safety reversing sensor , page 21 - Depending upon garage construction , wood blocks may need to be fastened to mounting locations before DXccoBr racket Arm sensors are installed . • Step 10 , page 22 - Alternate floor mounting of the • The opener can be installed within 2 feet to the left safety reversing sensor will require hardware not or right of the door center if there is a torsion spring provided . or center bearing plate in the way of the header • Step 11 , page 24 - Do you have a steel , aluminum , bracket or door bracket area . If your door has fiberglass or glass panel door ? If so , horizontal extension springs , the opener must be installed and vertical reinforcement is required . in the center of the door . See pages 12 and 24 . • Look at the garage door where it meets the floor . • Do you have an access door in addition to the It must close on the floor all the way across . garage door ? If not , Model 53702 Emergency Otherwise , the safety reverse system may not Key Release is required . See page 38 . work properly . See page 30 . Floor or door should • If your door is more than 7 feet high , see the rail be repaired . extension kits listed on page 38 . You may find it helpful to refer back to this page as you proceed with the installation of your opener .
Page: 5

One - Piece Door without Track Before you begin , survey your garage area to FINISHED CEILING see whether any of the conditions below apply Support bracket & fastening to your installation . hardware is required . See page 17 . Slack in chain tension is normal when garage door is closed , Header Wall Closed Position Cable Putley Bracket Cable Trottey Access Door 0 Emergency Release Rope & Handle Door Door Arm Arm eader Wall Door Reversing between floor and bottom Sensor Safety of door must not exceed 1 / 4 " . Reversing Sensor One - Piece Door with Track Based on your particular requirements , there are several installation steps which might call for materials and / or hardware not included in the carton . • Step 1 , page 13 - Look at the wall or ceiling above the garage door . The header bracket must be securely fastened to structural supports . • Step 5 , page 17 - Do you have a finished ceiling in your garage ? tf so , a support bracket and additional fastening hardware ( not supplied ) may be required . • Safety reversing sensor , page 21 - Depending on garage construction , wood blocks may need to be securely fastened to mounting locations before sensors are installed . Reversingr • Step 10 , page 22 - Alternate floor mounting of the Senso across width of door safety reversing sensor will require hardware that g Sensor is not provided . • Step 11 , page 25 - Generally , a one - piece door Closed Position does not require reinforcement . If your door is Cabie Cable Trolley Chain lightweight , you can refer to the information Pulley Bracket I I relating to sectional doors on page 24 . • Step 11 , page 25 - Depending on your door's eodeCrurved I construction , you might need additional mounting Hwa ' r BrackUeotorArm / I T - r i , hardware for the door bracket . _ % ° ° ° ° ° ° ° l ° ° ° ° _ J II I EmergencRyelease • Do you have an access door in addition to the Y / " / / I _ Door Straight _ Rope & Handle garage door ? If not , Model 53702 Emergency Key Garage - - _ / / ' _ Bracket Door Door Release is required . See page 38 . Arm • The gap between the bottom of the garage door and the floor cannot exceed 1 / 4 " . You may find it helpful to refer back to this page Otherwise , the safety reverse system may not as you proceed with the installation of your work properly . See page 30 . The floor or the door opener . should be repaired .
Page: 6

Carton Inventory Your garage door opener is packaged in two cartons which contain parts illustrated below . Accessories will depend on model purchased . If anything is missing , carefully check the packing material . Parts may be " stuck " in the foam . Hardware for assembly and installation is shown on page 7 . AII Models ModeI 53675 only ModeIs 53662 ( 2 ) , 53670 ( 1 ) , 53675 ( 2 ) SECURITY + Three - Function Remote Control with Visor Clip SECURITY + Premium Controt Console Multi - Function Keytess Entry Light Lens ( 2 ) White & White / Red 2 - Conductor Bell Wire Trotley Cable Putley Bracket Hanging Brackets Chain and Cable Header Bracket Door Bracket Safety Reversing Sensor Mounting Bracket With Square Holes ( 2 ) " C " Wrap ( 2 ) ol Curved Door Arm Section ol Safety LabeIs J ( 2 ) Safety Reversing Sensors and ( 1 Sending Eye and 1 Receiving Eye ) Literature I with Straight Door Safety Reversing Sensor 2 - Conductor White & White / Black Betl Wire Arm Section Mounting Bracket attached With Slot ( 2 )
Page: 7

Separate all hardware from the packages in the rail carton and the opener carton , as shown below , for the assembly and installation procedures . Assembly Hardware Washered Screw Hex Screw Nut Carriage Bolts 5 / 161 - 18xl / 2 " ( 2 ) 5 / 16 " - 18x7 / 8 " ( 3 ) 5 / 16 " - 18 ( 5 ) Master Link ( 2 ) 1 / 4 " - 20xl / 2 " ( 4 ) ( mounted in opener ) © © Lock Nut Lock Washer Trolley 1 / 4 " - 20x7 / 16 " ( 4 ) Threaded Shaft ( 1 ) 5 / 16 " ( 4 ) Installation Hardware Rail Grease _ IIH : xlLl _ eIlwI _ l 0 5 / 16 " - 18x7 / 8 " ( 4 ) Ring Fastener ( 3 ) © 1 I I I I I I I I I I I _ © Lag Screw Lock Washer 5 / 16 " ( 6 ) 5 / 16 " - 18xl - 7 / 8 " ( 2 ) Handle Nut 5 / 16 " - 18 ( 6 ) Rope _ lll , l , llllllllllllll > Screw Carriage Bott Dry Wall Anchors ( 2 ) 6ABxl " ( 2 ) 5 / 16 " - 18x2 - 1 / 2 " ( 2 ) ol oD Clevis Pin Clevis Pin Clevis Pin Insulated 5 / 16 " x2 - 3 / 4 " ( 1 ) 5 / 16 " x1 - 1 / 4 " ( 1 ) 5 / 16 " xl " ( 1 ) Staples ( 10 ) Safety Reversing Sensor Installation Hardware © Wing Nut ( 2 ) Lock Nut Carriage BoIts 1 / 4x1 - 1 / 2 " ( 4 ) 1 / 4 " - 20 ( 4 ) 1 / 4 " - 20xl / 2 " ( 4 ) © Hex Screw Lock Nut insulated Screw 1 / 4 - 20x1 - 1 / 2 " ( 2 ) : # 10x32 ( 4 ) Staples ( 20 ) # 10 - 32x3 / 8 " ( 4 )
Page: 8

Assembly Section : Pages 8 - 11 To avoid installation difficulties , do not run the garage door opener until instructed to do so . Make sure bolt necks are Assembly Step 1 seated in the square holes and rails are Assemble the T - rail & aligned before you Attach the Cable Pulley Bracket tighten lock nuts . ( See right and wrong views ) . @ Improper assembly can • Place the 3 T - rail sections on a flat surface for cause jerky trolley assembly . The end sections are identical . Make operation , noise and / or nuisance door reversals . Right Wrong sure the " arrow label " on the center section is pointing toward the door . • Insert the carriage bolts so the square bolt necks T - RAIL BACK seat in the square holes in the T - rail end sections ( TO OPENER ) and pass through the round holes in T - rail center section . Assemble lock nuts , ensure alignment and T - rait ( End Section ) tighten . 1 / 4 " Lock Nut \ \ @ Brace T - rait If T - rail is not assembled ( Center Section ) EXACTLY as shown , trolley will not travel smoothly along length of rail or it will hit against Brace the nuts . Hex Screws 5 / 16 " - 18x7 / 8 " T - rail ( End Section ) % \ Cable pulley bracket X attaches to FRONT Square Carriage END of T - rail Bolt Holes O T - RAIL FRONT Lock Washer ( TO DOOR ) 5 / 16 " Nut 5 / 16 " • Position the cable pulley bracket on the front end of the T - rail as shown . Fasten securely with the hardware . Hardware Shown Actual Size When © tightening the screws , be Lock Nut Carriage BoIts 1 / 4 " - 20x7 / 16 " 1 / 4 " - 20xl / 2 " sure to keep bracket parallel to the rail . Otherwise , the rail may bow when opener is Right Wrong Hex Screw Nut Lock Washer operated . 5 / 16 " - 18x7 / 8 " 5 / 16 " - 18 5 / 16 "
Page: 9

Hardware Shown Assembly Step 2 Actual Size Install the Trolley on the T - rail © • Attach the threaded shaft to the trolley with the lock washer and nuts as shown . Lock Washer Nut 5 / 16 " 5 / 16 " - 18 Lock Washer Outer Nat r _ Trotley Threaded Shaft Inner Nut 5 / 16 " Trolley Temporary Stop Screwdriver • As a temporary stop , insert a screwdriver into the \ hole in the front end of the T - rail . • Slide the trolley assembly along the rail to the screwdriver stop . If trolley hits against any nuts on the T - rail , the bolts and nuts were attached from the wrong side and must be repositioned . Review Step 1 . Assembly Step 3 Fasten the T - rail to the Opener I • Place the opener on packing material to protect the cover . For convenience , put a support under the cable pulley bracket . • Remove the ( 2 ) 5 / 16 " - 18x1 / 2 " washered screws mounted in the top of the opener . Washered Screw 5 / 16 " - 18xl / 2 " • Align the holes in the back section of the T - rail with Hex Screw the holes in the opener . 5 / 16 " - 18x7 / 8 " • Fasten the rail with the ( 2 ) washered screws Cover Protection previously removed . Tighten securely . Bott Hole Remember to use only these screws ! Any other screws will cause serious damage to the opener . T - raiI ( Back Section • Insert a 5 / 16 " - 18x7 / 8 " hex screw into the cover protection bolt hole in the T - rail as shown . Tighten securely with a 5 / 16 " lock washer and nut . NOTE : This screw prevents trolley over - travel . Keep a 2 " minimum between the trolley and this screw when adjusting travel limits ( see page 28 ) . Hardware Shown Actual Size Hex Screw Nut Lock Washer 5 / 16 " - 18x7 / 8 " 5 / 16 " 5 / 16 "
Page: 10

Assembly Step 4 Install the Chain / Cable & Serious injury can result if fingers become Attach the Sprocket Cover entangled in moving opener sprocket . Attach sprocket cover securely . Never operate opener while your hand is near the opener sprocket . Dispensing Carton Opener Figure 2 Sprocket Leave Chain and Cable Inside Dispensing Carton to Prevent Kinking . Keep Chain and Cable Taut When Dispensing • Detach the cable loop from the carton and fasten it to the trolley with a master link from the hardware bag . See master link procedure , Figure 1 . • With the trolley against the screwdriver , dispense Figure 3 the cable around the pulley . Master Link • Proceed back around the opener sprocket , Ctip - On Spring _ ' _ i Figure 2 . Be sure sprocket teeth engage the chain . Master Continue forward to the trolley threaded shaft , Link Cap _ Figure 3 . Master Link Flat End • Use the second master link to connect the Clip - On Spring of Trolley chain to the flat end of the shaft . Check Threaded Shaft i to make sure the chain is not Mast Link Cap ; _ Chain twisted . • Remove the screwdriver . T - rail Cable Loop Trolley Master Link Bar Figure 1 Cable Pulley Master Link Procedure : Install Chain and Cable Push pins of master link bar In This Direction through cable loop and hole in front end of trolley . Push cap Sprocket over pins and past notches . Cover Slide clip - on spring over cap Back Tab Slot and into notches until both pins are securely locked . Top of Opener To attach the sprocket cover : Front Tab Slot • Insert the back tab in the opener slot . Squeeze the Mounting cover slightly and insert the front tab in the slot on Plate the mounting plate . 10
Page: 11

Assembly Step 5 Tighten the Chain & Cable Lock Outer Nut Washer Inner Nut • Spin the inner nut and lock washer down the \ / 4 \ / threaded shaft , away from the trolley . To Tighten Outer Nut _ _ - " - _ _ _ , / • To tighten the chain , turn outer nut in the direction shown . As you turn the nut , keep the chain ° 2r thte from twisting . • When the chain is approximately 1 / 2 " above the base of the T - rail at its midpoint , re - tighten the inner nut to secure the adjustment . Sprocket noise can result if chain is either too loose or too tight . Chain When installation is complete , you may notice some chain droop with the door closed . This is normal . If the chain returns to the position shown when the I / 2 Inch door is open , do not re - adjust the chain . NOTE : During future maintenance , ALWAYS Base of T - rail pull the emergency release handle to disconnect trolley before adjusting chain . You have now finished assembling your garage door opener . Please read the following warnings before proceeding to the installation section : IMPORTANT INSTALLATION INSTRUCTIONS To reduce the risk of severe injury or death to persons : 1 . READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS . 2 . Install only on a properly balanced and lubricated garage door . An improperly balanced door may not reverse and could result in severe injury or death . Repairs to cables , spring assemblies and other hardware must be made by a professional service person before installing opener . 3 . Disable all locks and remove all ropes connected to the garage door before installing the opener . Ropes connected to a garage door can cause entanglement and death . 4 . If possible , install door opener 7 feet or more above floor with the emergency release handle mounted 6 feet above the floor . 5 . Do not connect the opener to power source until instructed to do so . 6 . Locate the Door Control within sight of the door at a minimum height of 5 feet where small children cannot reach , and away from all moving parts of the door . 7 . Install the User Safety Instruction Label on the wall adjacent to the door control and the Maintenance Instruction Label in a prominent location on the inside of the garage door . 8 . Upon completion of the installation , the door must reverse when it comes in contact with a one - inch high object or a 2x4 laid fiat on the floor . 9 . Do not wear watches , rings or loose clothing while installing or servicing an opener . Jewelry or loose clothing can be caught in the mechanism of the garage door or the opener . 11
Page: 12

Installation Section : Pages 12 - 27 Installation Step 1 Determine Header Bracket Location If the header bracket is not rigidly fastened to Installation procedures vary according to a structural support on the header wall or garage door types . Follow the instructions ceiling , the safety reverse system may not which apply to your door . work properly ( see page 30 ) . The door might not reverse when required , and could cause serious injury or death . The garage door springs , cables , pulleys , brackets and their hardware are under extreme tension . Do not attempt to loosen , move or adjust them yourself . Serious personal injury or death could result . Call for professional Finished Vertical garage door service . Ceiting Guideline Header Wall 2x4 Structural • Close the door and mark the inside Supports vertical centerline of the garage door . • Extend the line onto the header wall above the door . Remember , you can fasten the header bracket within 2 feet of the left or right of the door center only if a torsion spring or center bearing plate is in the way ; or you can attach it to the ceiling ( refer to page 14 ) when clearance is minimal . ( It may be mounted on the wall upside down if necessary , to gain approximately 1 / 2 " . ) If you need to install the header bracket on a 2x4 ( on wall or ceiling ) , use lag screws ( not supplied ) to securely fasten the 2x4 to structural supports as shown here and on page 13 . Ceiling Wall Header • Open your door to the highest , , 2 " Track _ WaII Track point of travel as shown . Draw Header 1 2 ' ' i an intersecting horizontal line Highest Point on the header wall 2 " above of Travel Highest Point the high point . This height will of TraveI provide travel clearance for the top edge of the door . Door Door clearance brackets are available for sectional doors when headroom clearance is less than 2 " . See accessory page 38 . Sectional door One - piece door with curved track with horizontal track Proceed to Step 2 , page 14 . 12
Page: 13

Read the Safety instructions on page 12 . They also apply to doors without tracks . Unfinished Header Wall Vertical Centedine 2x4 • Close the door and mark the inside vertical centerline of your garage door . Extend the line onto the header wall above door . If headroom clearance is minimal , you can install the header bracket on the ceiling . OPTIONAL CEILING MOUNT See page 14 . FOR HEADER BRACKET • If you need to instafl the header bracket on a 2x4 ( on wall or ceiling ) , use lag screws ( not supplied ) to securely fasten the 2x4 to structural supports as shown . Header Wall Header Highest Point . . . . - - - Wall of TraveI Highest Point of Travel _ jamb III / c i c _ Hardware One - piece door without track One - piece door without track jamb hardware pivot hardware EXAMPLE • Open your door to the highest point of travel as shown . Measure the distance from the top of the Distance from top of door door to the floor . Subtract the actual height of the ( at highest point of travel ) to floor . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 " door . Add 8 " to the remainder . ( See Example ) . Actual height of door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 88 " • Close the door and draw an intersecting horizontal Remainder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 " line on the header wall at the determined height . Add . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . + 8 " If the total number of inches exceeds the height Bracket height on header wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . = 12 " available in your garage , use the maximum height possible , or refer to page 14 for ceiling ( Measure UP from top of CLOSED door . ) installation . Proceed to Step 2 , page 14 . 13
Page: 14

You can attach the header bracket either to the Installation Step 2 wall above the garage door , or to the ceiling , Follow the instructions which will work best for Install the Header Bracket your particular requirements . Fasten the Header Bracket to the Wall • Center the bracket on the vertical guideline with • Mark either set of bracket holes ( do not use the the bottom edge of the bracket on the horizontal holes designated for ceiling mount ) . Drill 3 / 16 " pilot line as shown ( with the arrow pointing toward the holes and fasten the bracket securely to a structural ceiling ) . support with the hardware provided . Wall Mounting Holes / / Header / Wall Lag Screws 5 / 16 " x9x1 - 5 / 8 " 2x4 Structural Door Support Spring The nail hole is for positioning only . You must use lag screws to mount the header bracket Optional Wall Mounting Holes / / / / em Door Hardware Shown Actual Size - 1 Highest Point of Travel Vertical ( of Garage Door ) Center Line " > 5 / 16 " - 9xl - 5 / 8 " Fasten the Header Bracket to the Ceiling • Extend the vertical guideline onto the ceiling as shown . • Center the bracket on the vertical mark , no more than 6 " from the wall . Make sure the arrow is pointing toward the wall . The bracket can be mounted flush against the ceiling when clearance is minimal . • Mark holes designated for ceiling mount only . Drill 3 / 16 " pilot holes and fasten bracket securely to a structural support with the hardware provided . Door Ceiting Mounting Holes Spring Header Wall The nail hole is for positioning only You must use lag screws to mount the header bracket 14
Page: 15

Installation Step 3 Attach the T - rail to the Header Bracket • Position the opener on the garage floor below the header bracket . Use packing material as a protective base . Header If the door spring is in the way you'll need help . Bracket Have someone hold the opener securely on a temporary support to allow the T - rail to clear the Cable spring , Bracket • Position the cable pulley bracket against the header bracket . • Align the bracket holes and join with a clevis pin as shown . • Insert a ring fastener to secure . Ring Fastener Header Bracket ' 0 i J Ctevis Pin 5 / 16 " x2 - 3 / 4 " Cable Putley Bracket Door Temporary Support Hardware Shown Actual Size o ] O Clevis Pin 5 / 16 " x2 - 3 / 4 " Ring Fastener 15
Page: 16

Installation Step 4 Position the Opener Follow instructions which apply to your door type as illustrated . A 2x4 laid fiat is convenient for setting an ideal door - to - T - rail distance . 2x4 Laid Fiat • Raise the opener onto a stepladder . You will need help at this point if the ladder is not tall enough . • Open the door all the way and place a 2x4 laid fiat Door on the top section beneath the T - rail . If the top panel hits the trolley when you raise the door , pull down on the trolley release arm to disconnect the inner and outer sections . The trolley can remain disconnected until Step 12 is completed . _ [ _ ' - @ _ ' / _ @ _ Trolley Trol _ ase Arm • With the door fully open and parallel to the floor , Top of Opener measure the distance from the floor to the top of the door . 1I . . . . . • Using a stepladder as a support , raise the opener to the same distance as the door from the floor ( it Top will be at a slight angle as shown ) . • The top of the door should be level with the top of the opener . Do not position the opener more than i of Door 2 " above this point . 16
Page: 17

Installation Step 5 Hang the Opener Two representative installations are shown . Yours may be different . Hanging brackets should be angled , Figure 1 , to provide rigid support . On Figure 1 finished ceilings , Figure 2 , attach a sturdy metal bracket to structural supports before installing the opener . The bracket and fastening hardware are not supplied . See accessory page 38 . i / ' Supports • Measure the distance from each side of the opener to the structural support . • Cut both pieces of the hanging bracket to required Measure Lag Screws Distance 5 / 16 " - 18xl - 7 / 8 " lengths . 5 / 16 " - 18x7 / 8 " Screw • Drill 3 / 18 " pilot holes in the structural supports . • Attach one end of each bracket to a support with 5 / 18 " - 18xl - 7 / 8 " lag screws . • Fasten the opener to the hanging brackets with 5 / 16 " - 18x7 / 8 " screws , lock washers and nuts . • Check to make sure the T - rail is centered over the door ( or in line with the header bracket if the bracket is not centered above the door ) . • Remove the 2x4 . Operate the door manually . If the Figure 2 door hits the rail , raise the header bracket . 5 / 16 " - 18x7 / 8 " Screw \ 5 / 16 " Lock Washer \ 5 / 16 " - 18 Hardware Shown Actual Size Lag Screw 5 / 16 " - 18xl - 7 / 8 " O , , , , , , © , , , , D © Hex Screw 5 / 16 " - 18x7 / 8 " Nut 5 / 16 " - 18 Lock Washer 5 / 16 " 17
Page: 18

Installation Step 6 Install the Premium Control Console Do not connect to five electrical wiring . Connect only to 24 Volt low voltage wires . Connection to Locate the door control within sight of the door five wires or higher voltage may cause serious at a minimum height of 5 feet where small injury from shock , burn or electrocution . children cannot reach , and away from all moving Children operating or playing with a garage parts of the door and door hardware . door opener can injure themselves or others . The garage door could close and cause The door control is typically attached directly to the serious injury or death . wall . If installing into drywall , drill 5 / 32 " holes and use the anchors provided . For pre - wired installations Install the door control ( or any additional push ( as in new home construction ) , Console models buttons ) out of the reach of children and away from all moving parts of the door and door may be mounted to a standard single gang box hardware , but where the garage door is visible . ( Figure 2 ) . Do not allow children to operate the push 1 . Strip 1 / 4 " of insulation from one end of the bell button ( s ) or the remote control ( s ) . wire and connect it to the two screw terminals on A moving garage door could injure someone the back of the door control : white to 2 , and under it . Activate the opener only when the white / red to 1 . door is properly adjusted , you can see it 2 . Pry off cover along one side with a screwdriver clearly , and there are no obstructions to door blade ( see Figure 1 ) . Fasten with 6ABx1 - 1 / 4 " self - travel . tapping screws ( standard installation ) or 6 - 32x1 " machine screws ( pre - wired installation ) as follows : Hardware Shown Actual Size • Install bottom screw , allowing 1 / 8 " to protrude above wall surface . • Position bottom of door control on screw head and _ ] I I 1161AI _ I ! I ! II i _ , 1 , Is ! rl ! IvII ] _ Insulateds slide down to secure . Adjust screw for snug fit . Stapte Control Console ( std installation ) • Drill and install top screw with care to avoid cracking plastic housing . Do not overtighten . • Insert top tabs and snap on cover . Control Console ( pre - wired ) Dry Wall Anchors 3 . ( For standard installation ) Run the bell wire up the wall and across the ceiling to the opener . Use Figure 1 Figure 2 insulated staples to secure the wire in several REMOVE & REPLACE COVER PRE - WIRED places . Be careful not to pierce the wire with a INSTALLATION To Replace , To Remove , staple , creating a short . Insert Twist Top Tabs Here 4 . Connect the bell wire to the terminal screws on the opener panel : white to 2 ; white / red to 1 . 5 . Position the antenna wire as shown . 24 Volt ' 2 - Conductor Belt Wire 2 - Conductor Opener Bell Wire Top Lighted Mounting O Push Button Hole [ ] - erminal _ > Screws / Bottom Mounting Hole Lig BACK VIEW Lock PREMIUM CONTROL CONSOLE 18
Page: 19

6 . AttachtheUserSafetyInstructionlabeltothewall Do NOT connect the power and operate the nearthedoorcontrola , ndtheMaintenance opener at this time . The trolley will travel to the Instructionlabelina prominenlot cationonthe full open position but will not return to the insideof thegaragedoor . close position until the sensor beam is connected and properly aligned . Page 32 explains how to use the door control . See Safety Reversing Sensor instructions beginning on page 21 . Installation Step 7 Install the Lights and the Lenses I Install the lights : • Install a 75 watt maximum light bulb in each socket . The lights will turn ON and remain lit for 75 Watt Max approximately 4 - 1 / 2 minutes when power is Lens Light Bulb Tab connected . Then the lights will turn OFF . Lens • If the bulbs burn out prematurely due to vibration , Guide replace them with standard neck " Garage Door Lens Opener " bulbs . Slot Install the lenses : Lens Tab • Apply slight pressure on the sides of each lens and slide the tabs into the slots in the side panels . Lens f • For convenience , the lenses may be installed Tab after Adjustment Step 4 on page 30 . • Reverse the procedure to remove the lenses . Installation Step 8 Attach the Emergency Release Rope and Handle Do not use the red handle to pull the door open or closed . The rope knot could become untied and you could fall . Use the emergency • Thread one end of the rope through the hole in release only to disengage the trolley and , if the top of the red handle so " NOTICE " reads right possible , only when the door is closed . side up as shown . Secure with an overhand knot . Garage doors are heavy . If the door is open The knot should be at least 1 " from the end of when the handle is pulled , the door could the rope to prevent slipping . close inadvertently if it is not properly balanced . Serious injury may result to persons • Thread the other end of the rope through the hole under the door . Make sure the doorway is clear in the release arm of the outer trolley . of persons and obstructions before pulling • Adjust rope length so the handle is 6 feet above handle when door is open . the floor . Secure with an overhand knot . If it is necessary to cut the rope , heat seal the cut end with a match or lighter to prevent Overhand unraveling . Knot Trotle _ _ T _ olley Rope Release Arm _ " Emergency _ Release Handle Overhand Knot 19
Page: 20

Installation Step 9 Electrical Requirements To prevent electrocution or fire , installation and wiring must be in compliance with local electrical and building codes . To reduce the risk of electric shock , your garage Do NOT use an extension cord , 2 - wire adapter , door opener has a grounding type plug with a third or change the plug in any way to make it fit grounding pin . This plug will onlyfit into a grounding your outlet . type outlet . If the plug doesn't fit into the outlet you have , contact a qualified electrician to install the proper outlet . II To avoid installation difficulties , do not run the opener at this time . I Right Wrong If permanent wiring is required by your local code , refer to the following procedure : Permanent Wiring To make a permanent connection through the Connections 7 / 8 " diameter hole in the top of the opener ( according to local code ) : Ground Tab • Remove the opener cover screws and set the cover aside . Green Ground • Remove the attached 3 - prong cord . Screw • Connect the black ( line ) wire to the screw on the Black brass terminal ; the white ( neutral ) wire to the Wire Wire screw on the silver terminal ; and the ground wire to the green ground screw . The opener must be grounded . • Reinstall the cover . White Wire Black Wire I To avoid installation difficulties , I do not run the opener at this time . I 2O
Page: 21

The Safety Reversing System Information you'll need before you begin the installation of the safety reversing sensor . The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction . This is a required safety device and cannot be disabled . Without a properly working safety reversing sensor , persons ( particularly children ) could be injured or killed by a closing garage door . Installation procedures are the same for sectional Read and follow all instructions . and one - piece doors . To protect small children , install the safety reversing sensor so that the beam will be no higher than 4 " - 6 " above the garage floor . Disconnect power to the garage door opener before installing the safety reversing sensor . Be sure power to the opener is disconnected . The brackets must be securely fastened to a solid surface such as the studs on either side of the door , The sending eye transmits an invisible light beam to or add a piece of wood at each location if installing in the receiving eye . The units can be installed on masonry construction . either side of the garage door as long as the sun never shines directly into the receiving eye lens . The invisible light beam path must be unobstructed . Look at the label on the connector end of each case No part of the garage door ( or door tracks , springs , hinges , rollers or other hardware ) can interrupt the to identify the sensors . beam while the door is closing . If it does , use a piece The brackets must be connected and fastened so of wood to build out each sensor mounting location to that the sending and receiving eyes face each other the minimum depth required for light beam clearance . as shown in Figure 1 . If an obstruction breaks the light beam while the garage door is closing , the door will stop and reverse to full open position and the opener lights will flash for 5 seconds . Sensor Beam 4 - 6 " max above floor / Figure 1 : Facing the door from inside the garage 21
Page: 22

Installation Step 10 Install the Safety Reversing Sensor I Figures 2 and 3 show assembly of brackets and Figure 2 Mounting Bracket " C " wrap based on the recommended installation of With Square Holes the sensors as shown on page 21 . . J " C " Wrap However , Figures 4 and 5 are variations which may i / , ii fit your installation requirements better . Make sure the wraps and brackets are aligned so the # 10 - 32 sensors will face each other across the garage Lock Nuts door . # 10 - 32x3 / 8 " • Fasten the " C " wraps to the mounting brackets Screws having square holes , using the hardware shown in Figure 2 . • Connect each assembly to a slotted bracket , using Figure 3 the hardware shown in Figure 3 . Note the alignment of the brackets for left and right sides of the door . 1 / 4 - 20xl / 2 " Carriage Bolts ( with square shoulder ) • Finger tighten the lock nuts . • Use bracket mounting holes as a template to locate and drill ( 2 ) 3 / 16 " diameter pilot holes on both sides of the garage door , 4 " - 6 " above the floor but not exceeding 6 ' : ( See warning on page 21 . ) • Attach bracket assemblies with 1 / 4 " x1 - 1 / 2 " lag J screws as shown in Figure 3 . j Bracket " C " Wrap with Slot • Adjust right and left side bracket assemblies to the / _ M . ounting Bracket same distance out from the mounting surface . Make sure all door hardware obstructions are f _ / 1 / 4 " - 20 _ uare Holes _ OCKNuts cleared . Tighten the nuts securely . Hardware Shown Actual Size © © # 10 - 32x3 / 8 " # 10x32 1 / 4 " - 20xl / 2 " 1 / 4 " - 20 Screw Lock Nut Lock Nut Lag Screw Staples Carriage Bolts Figure 4 Figure 5 Alternate Wall Mount Alternate Floor Mount Inside Inside Garage Garage Sensor with wire Wall T Wall , / Indicat ° r Light Mounting Bracket with Slot Mounting Bracket with Square Holes _ Mounting eBrackets with Square Hol Mounting Bracket j with Stot Attach with concrete anchors with wire ( not provided ) indicator Light Garage Floor 22
Page: 23

• Centereachsensorunitina " C " wrapwithlenses Figure 6 " c " wrap _ _ W _ ntg pointingtowardeachotheracrossthedoor ( see Figure6 ) . Indicator _ : • Securesensorswiththehardwareshown . Finger Light _ tightenthewingnutonthereceiving eye to allow for final adjustment . Securely tighten the sending 1 / 4 _ 20 / _ X 1 _ 1 / _ ith W ! re _ eye wing nut . Hex Bolt I _ • Run the wires from both sensors to the opener . Use insulated staples to secure wire to wall and Trouble Shooting ceiling . 1 . If the sending eye indicator light does not glow • Strip 1 / 4 " of insulation from each set of wires . steadily after installation , check for : Separate white and white / black wires sufficiently to • Electric power to the opener . connect to the opener terminal screws : white to 2 • A short in the white or white / black wires . These and white / black to 3 . can occur under staples or at screw terminal Aligning the Safety Sensors connections . • Plug in the opener . Green indicator lights in both • Incorrect wiring between sensors and opener . the sending and receiving eyes will glow steadily if • An open wire ( wire break ) . wiring connections and alignment are correct . 2 . If the sending eye indicator light glows steadily but The sending eye indicator light will glow regardless the receiving eye indicator light doesn't : of alignment or obstruction . If the indicator light is • Check alignment . off , dim , or flickering in the receiving eye ( and the invisible light beam path is not obstructed ) , • Check for an open wire to the receiving eye . alignment is required . 3 . If the receiving eye indicator light is dim , realign • Loosen the sending eye wing nut and readjust , either sensor . aiming directly at the receiving eye . Lock in place . NOTE : When the invisible beam path is obstructed or • Loosen the receiving eye wing nut and adjust misaligned while the door is dosing , the door will sensor vertically and / or horizontally until it receives reverse . If the door is already open , it will not close . the sender's beam . When the green indicator light The opener lights will flash 10 times . ( ff bulbs are not glows steadily , tighten the wing nut . installed , 10 clicks are audible . ) See page 21 . Hardware Shown Actual Size Figure 7 1 / 4 - 20x1 - 1 / 2 " Hex Bott Connect Wire to Opener TerminaIs Bell Wire Door Control Sensor Connections - - _ _ . Connections . _ Bell Wire ( dotted line ) OPENER TERMINAL SCREWS / Sensor Invisible Light Beam Sensor Protection Area 23
Page: 24

Installation Step 11 Fasten Door Bracket To prevent damage to steel , aluminum , Follow instructions which apply to your door fiberglass or glass panel doors , always type as illustrated below or on page 25 . reinforce the inside of the door both vertically and horizontally with an angle iron . A horizontal brace should be long enough to be secured to 2 vertical supports . A vertical brace should cover the height of the top panel . The illustration shows one piece of angle iron as the horizontal brace . For the vertical brace , 2 pieces of angle iron are used to create a " U " - shaped support . The best solution is to check with your garage door manufacturer for an opener installation door reinforcement kit . Header Bracket is needed for lightweight garage doors ( fiberglass , aluminum , steeI , Figure 1 doors with glass panel , etc ) . Reinforcement Vertical GuideIine Door e / / Location uP Carriage Bolt 5 / 16 ' L18x21 / 2 ' Door Bracket Washer 5 / 16 " Nut 5 / 16 " - 18 Figure 2 Inside Edge of Door or Reinforcement Board _ UP . . . . . • Center the door bracket on the previously marked Door Bracket vertical guideline used for the header bracket installation . Note correct UP placement , as stamped inside the bracket . • Position the bracket on the face of the door within the following limits : Hardware Shown Actual Size A ) The top edge of the bracket 2 " - 4 " below the top edge of the door . B ) The top edge of the bracket directly below any © © structural support across the top of the door . Nut 5 / 16 - 18 Lock Washer 5 / 16 " • Mark and drill 5 / 16 " left and right fastening holes . Secure the bracket as shown in Figure 1 if there is vertical reinforcement . If your installation doesn't require vertical reinforce - ment but does need top and bottom fastening holes Carriage Bolt 5 / 16 ' L18X2 - 1 / 2 " for the door bracket , fasten as shown in Figure 2 . 24
Page: 25

Please read and comply with the warnings and reinforcement instructions on page 24 . They apply to one - piece doors also . Header Walt - - Finished Ceiling - - 2x4 Support Header Horizontal and vertical Bracket Door reinforcement is needed for Bracket Placement lightweight garage doors of Door ( fiberglass , aluminum , steel , Bracket _ _ door with glass panet , etc ) _ _ - - - - - - Vertical ® Nut Garage Door 5 / 16 " 5 / 16 " - 18 Top of Door ( Inside Garage ) Bracket Top rEdge of Doo _ _ Optional Door Placement For a door with no _ Carriage Bolt the optional instaIlation , exposed framing or for _ _ - 5 / 16 " - 18x2 - 1 / 2 " use 5 / 16 " xl - 1 / 2 " lag screws ( not supplied ) to fasten • Center the bracket on the top of the door , in line with the header bracket as shown . Mark holes . Hardware Shown Actual Size • Drill 5 / 16 " pilot holes and fasten the door bracket with hardware supplied . If the door has no exposed framing , drill 3 / 16 " pilot holes and fasten the bracket with 5 / 16 " x1 - 1 / 2 " lag © © screws ( not supplied ) to the top of the door . Nut 5 / 16 " - 18 Lock Washer 5 / 16 " The door bracket may be installed on the top edge of the door if required for your installation . ( Refer to the dotted line optional placement drawing . ) Drill 3 / 16 " pilot holes and substitute Carriage Bolt 5 / 16 " - 18x2 - 1 / 2 " 5 / 16 " x1 - 1 / 2 " lag screws ( not supplied ) to fasten the bracket to the door . 25
Page: 26

Installation Step 12 Connect Door Arm to Trolley Follow instructions which apply to your door type as illustrated below and on page 27 . Make sure garage door is fully closed . Pull the emergency release handle to disconnect the outer trolley from the inner trolley . Slide the outer trolley back ( away from the door ) about 2 " as shown in Figures 1 , 2 and 3 . Figure 1 : Figure 2 : • Fasten straight door arm section to outer trolley • Bring arm sections together . Find two pairs of holes with the the 5 / 16 " xl " clevis pin . Secure the that line up and join sections . Select holes as far connection with a ring fastener . apart as possible to increase door arm rigidity . • Fasten curved door arm to the door bracket in the same way , using the 5 / 16 " x1 - 1 / 4 " clevis pin . Inner Trotley / Outer Tro Lock / / II I I _ clevisP _ n . . . _ , , , , Iol , - , Ik Emergency r _ u [ s _ _ _ Release 5 / 16 " - 18 \ / _ / v - - Handte _ . , ° Ooor Straioht _ , \ oo / o / I Do _ Bracket Figure 2 ; rr % Figure1 Hole Alignment Alternative Figure 3 : • If holes in curved arm are above holes in straight arm , disconnect straight arm . Cut about 6 " from the solid end . Reconnect to trolley with cut end down as shown . • Bring arm sections together . • Find two pairs of holes that line up and join with screws , lock washers and nuts . Hardware Shown Actual Size Screws % 5 / 16 " - 18x7 / 8 " O © © Cut This End Nut 5 / 16 " - 18 Lock Washer 5 / 16 " Ring Fastener ] O Figure 3 Clevis Pin Hex Screw Clevis Pin 5 / 16 " xl " ( Trolley ) 5 / 16 " x1 - 1 / 4 " ( Door Bracket ) 5 / 16 " - 18x7 / 8 " Proceed to Adjustment Step 1 , page 28 . Trolley will re - engage automatically when the opener is operated . 26
Page: 27

Assemble the Door Arm : Door Ring • Fasten the straight and curved door arm sections Bracket _ 1 _ - - - - Fastener Nuts together to the longest possible length , with a 2 or 3 Lock , , _ _ " _ " ' _ , _ - _ W ashe rs 5 / 16 - 18 hole overlap . ' 5 / 16 , , I • With the door closed , connect the straight door arm ClevPiins Straight % e - I I , ' 1 section to the door bracket with the 5 - 16 " x 1 - 1 / 4 " clevis pin . Screws / ' a _ . _ . _ - _ > _ 4 ] _ v j \ 5 / 16 , L18x7 / 8 z _ _ Curved • Secure with a ring fastener . Door Arm On one - piece doors , before connecting the door arm to the trolley the travel limits must be adjusted . Limit adjust - ment screws are located on the left side panel as shown on page 28 . Follow adjustment procedures below . FullyClosed Trolley I Closed Door Arm I Door Open Door Door with I I Backward Slant Adjustment Procedures for One - Piece Doors Open Door Adjustment : Closed Door Adjustment : Decrease UP limit Decrease DOWN limit • Turn the UP limit adjustment screw counter - • Turn the DOWN limit adjustment screw clockwise clockwise 5 - 1 / 2 turns . 5 complete turns . • Press the Wall Control push bar . The trolley will • Press the Wall Control push bar . The trolley will travel to the fully open position . travel to the fully closed position . • Manually raise the door to the open position • Manually close the door and lift the door arm to the ( parallel to the floor ) , and lift the door arm to the trolley . The arm should touch the trolley just ahead trolley . The arm should touch the trolley just in of the door arm connector hole . Refer to the fully back of the door arm connector hole . Refer to the closed trolley / door arm positions in the illustration . If fully open trolley / door arm positions in the the arm is behind the connector hole , adjust the limit illustration . If the arm does not extend far enough , further . One full turn equals 2 " of trolley travel . adjust the limit further . One full turn equals 2 " of trolley travel . Connect the door arm to the trolley . • Close the door and join the curved arm to the connector hole in the trolley with the remaining clevis pin . It may be necessary to lift the door slightly to make the connection . • Secure with a ring fastener . • Run the opener through a complete travel cycle . If the door has a slight " backward " slant in full open position as shown in the illustration , decrease the UP limit until the door is parallel to the floor . 27
Page: 28

Adjustment Section : Pages 28 - 30 Adjustment Step 1 Adjust the UP and DOWN Limits Do not make any limit adjustments until the Improper adjustment of the travel limits will safety reversing sensors are completely interfere with the proper operation of the installed . safety reverse system . The door might not reverse properly when required and could seriously injure or kill someone under it . Test the safety reverse system following all Limit adjustment settings regulate the points at adjustments to the travel limits . See page 30 . which the door will stop when moving up or down . The door will stop in the up direction if anything interferes with door travel . The door will reverse in the down direction if anything interferes with the door travel ( including binding or unbalanced doors ) . To operate the opener , press the Door Control push button . Run the opener through a complete travel cycle . • Does the door open and close completely ? • Does the door stay closed and not reverse unintentionally when fully closed ? Cover / If your door passes both of these tests , no limit _ ; . . . . i _ _ " O Le % St _ ideC ) iaOil _ l Protection adjustments are necessary unless the reversing test Bolt fails ( See page 30 ) . Limit Adjustment Adjustment procedures are outlined below . Run Screws the opener through a complete travel cycle after each adjustment . Repeated operation of the opener during adjustment procedures may cause the motor to Adjustment Label overheat and shut off . Simply wait 15 minutes and try again . Read the procedures carefully before proceeding to Adjustment Step 2 . Use a screwdriver to make limit adjustments . How and When to Adjust the Limits • If the door does not open completely , but If you have adjusted the door arm to the maximum opens at least five feet : length and the door still will not close completely , lower the header bracket . See Installation Step 1 , Increase up travel . Turn the UP limit adjustment pages 12 and 13 . screw clockwise . One turn equals 2 " of travel . NOTE : To prevent the trolley from hitting the • If the opener reverses in fully closed position : cover protection bolt , keep a minimum distance Decrease down travel . Turn the DOWN limit of 2 - 4 " between the trolley and the bolt . adjustment screw clockwise . One turn equals 2 " of travel . • If door does not open at least 5 feet : Adjust the UP ( open ) force as explained in • If the door reverses when closing and there is Adjustment Step 2 . no visible interference to travel cycle : If the opener lights are flashing , the Safety Reversing • If the door does not close completely : Sensors are either not installed , misaligned , or Increase down travel . Turn the DOWN limit obstructed . See Troubleshooting , page 23 . adjustment screw counterclockwise . One turn Test the door for binding : Pull the manual release equals 2 " of travel . handle . Manually open and close the door . If the door If the door still won't close completely and the trolley is binding , call for garage door service . If the door is bumps into the pulley bracket ( see page 4 or 5 ) , try not binding or unbalanced , adjust the DOWN ( close ) lengthening the door arm , ( see page 26 ) . force . See Adjustment Step 2 . 28
Page: 29

Adjustment Step 2 Adjust the Force Too much force on the door will interfere with the proper operation of the safety reverse Force adjustment controls are located on the right system . The door might not reverse properly side panel of the opener . Force adjustment settings when required and could seriously injure or regulate the amount of power required to open and kill someone under it . Do not increase the close the door . force beyond the minimum amount required to close the door . Do not use the force The door will stop in the up direction if anything adjustments to compensate for a binding or interferes with its travel . The door will reverse in the sticking garage door . Test the safety reverse down direction if anything interferes with its travel system following all adjustments to force ( including binding or unbalanced doors ) . levels . See page 30 . If the forces are set too light , door travel may be interrupted by nuisance reversals in the down direction and stops in the up direction . Weather Force Adjustment conditions can affect the door movement , so Controls occasional adjustment may be needed . The maximum force adjustment range is 260 degrees , 000 about 3 / 4 of a complete turn . Do not force controls beyond that point . Turn force adjustment controls with a screwdriver . Right Side Panel Adjustment Labet How and When to Adjust the Forces Test the DOWN ( close ) force Make 10 degree turn adjustments until the door stops easily . After each adjustment , run the opener through Grasp the door bottom when the door is about a complete travel cycle . halfway through DOWN ( close ) travel . The door should reverse . Reversal halfway through down If the door doesn't open at least 5 feet travel does not guarantee reversal on a one - inch Increase UP ( Open ) force by turning the control obstruction . See page 30 . tf the door is hard to clockwise . Make 10 degree turn adjustments until hold or doesn't reverse , decrease the DOWN ( close ) door opens completely . Re - adjust the UP limit if force by turning the control counterclockwise . necessary . After each adjustment , run the opener Make 10 degree turn adjustments until the door through a complete travel cycle . reverses normally . After each adjustment , run the opener through a complete cycle . If the door reverses during the down ( close ) cycle and the opener lights aren't flashing Test the UP ( open ) force Increase DOWN ( close ) force by turning the control Grasp the door bottom when the door is about clockwise . Make 10 degree turn adjustments until the halfway through UP ( open ) travel . The door should door completes a close cycle . After each adjustment , stop . If the door is hard to hold or doesn't stop , run the opener through a complete travel cycle . Do decrease UP ( open ) force by turning the control not increase the force beyond the minimum counterclockwise . amount required to close the door . 29
Page: 30

Adjustment Step 3 Test The Safety Reversing Sensor Without a properly working safety reversing sensor , persons ( particularly children ) could be • Press the remote control push button to open the seriously injured or killed if trapped by a closing door . garage door . Repeat this test once a month , • Place the opener carton in the path of the door . • Press the remote control push button to close the door . The door will not move more than an inch , and the opener light ( s ) will flash . Professional service is required if the opener closes the door when the safety reversing sensor is obstructed . The garage door opener will not close from a remote control if the indicator light in either sensor is off ( alerting you to the fact that the sensor is misaligned or obstructed ) , The garage door can be closed by pressing and holding the Door Control push button until down f travel is completed . Safety Reversing Sensor Safety Reversing Sensor Adjustment Step 4 Test the Safety Reverse System Failure to test and adjust the safety reverse system may result in serious injury or death to persons trapped by a closing garage door . Repeat this test once a month and adjust as needed . Test : GARAGE DOOR • Place a one - inch board ( or a 2x4 laid flat ) on the floor , centered under the garage door . • Operate the door in the down direction . The door must reverse on striking the obstruction . Adjustment : If the door stops on the obstruction , it is not traveling far enough in the down direction . • Increase the DOWN limit by turning the DOWN limit adjustment screw counterclockwise 1 / 4 turn . • Repeat the test . On a sectional door , make sure limit adjustments do not force the door arm beyond a straight up and down position . See the illustration on page 26 . • When the door reverses on the one - inch board , remove the obstruction and run the opener through 3 or 4 complete travel cycles to test adjustment . Important safety check If the door will not reverse after repeated Repeat Adjustment Steps 1 , 2 and 4 after : adjustment attempts , call for professional garage door service . • Each adjustment of door arm length , force controls or limit controls . • Any repair to or adjustment of the garage door ( including springs and hardware ) . • Any repair to or buckling of the garage floor . • Any repair to or adjustment of the opener . 30
Page: 31

IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of severe injury or death to persons : 1 . READ AND FOLLOW ALL INSTRUCTIONS . 5 . If possible , use the emergency release only when the door is in a closed position . Cautionord 2 . Do not permit children either to operate or to should be taken whenever the disconnect c play with the opener . Keep remote control in a is actuated with the door open . Weak or broken location inaccessible to children . springs may cause the door to fall rapidly , 3 . Operate opener only when the door is in full causing injury or death to persons . view and free from any obstruction . Keep the 6 . KEEP GARAGE DOORS PROPERLY door in sight until it is completely closed . NO BALANCED . See page 3 . An improperly ONE SHOULD CROSS THE PATH OF THE balanced door may not reverse when required MOVING DOOR . and could result in severe injury or death . 4 . Check safety reversal system monthly . See Repairs to cables , spring assemblies and other page 30 . The garage door MUST reverse on hardware must be made by a professional contact with a one - inch ( or a 2x4 board laid garage door person . fiat ) object placed on the floor . If an adjustment 7 . Disconnect the electric power to the garage is made to either the force or the limit of travel , door opener before making any repairs or both adjustments may be needed and the removing the covers . safety reversal system must be checked . Failure to properly adjust the opener may 8 . SAVE THESE INSTRUCTIONS . result in severe injury or death . Care of Your Opener 3 - FUNCTION The remote control Limit and force adjustment controls Open this end The lithium batteries should first to avoid / _ L . . _ _ . _ j ¢ - _ Limit Controls Force Controls crackin _ g " _ = _ - _ - _ / produce power for up to 5 years . To replace batteries , hous _ use the visor clip or screwdriver blade to pry open the case as COMPACT _ Twist tier e _ , 7 ' _ _ _ C > _ 7 shown . ( " Open " location is Adjustment Labet Adjustment Label to open _ - - _ stamped on back of remote ( Located on the teft side panel ) ( Located on the right side panel ) control case . ) Insert batteries positive side down . Weather conditions may cause some minor Replace cover as follows . 3 - Function remote : Insert changes in door operation requiring some re - the 3 tabs at the opposite end and snap shut . adjustments , particularly during the first year of Compact 3 - Function remote : Snap shut along both sides . operation . Pages 28 and 29 refer to the limit and force Dispose of old batteries properly . adjustments . Only a screwdriver is required . Follow the instructions carefully . Repeat the safety reverse test ( page 30 ) after any adjustment of limits or force . Maintenance Schedule Once a Month Twice a Year Manually operate door . If it is unbalanced or Check chain tension . Disconnect trolley first . binding , call for professional garage door service . Adjust if necessary ( See page 11 ) . Once a Year Check to be sure door opens and closes fully . Adjust limits and / or force if necessary . Oil door rollers , bearings and hinges . The opener ( See pages 28 and 29 . ) does not require additional lubrication . Do not Repeat the safety reverse test . Make any grease the door tracks . necessary adjustments ( See page 30 ) . 31
Page: 32

Operation of Your Opener Activate the opener with any of the following : • The Remote Control : Hold push button down until the door starts to move . • The Door Control : Hold push button down until Weak or broken springs could allow an open the door starts to move . door to fall ( either rapidly or unexpectedly ) , resulting in serious injury , death or property • The Outdoor Key Switch or Keyless Entry : ( See damage . If possible , use the emergency Accessories ) release rope and handle only when the door is When the opener is activated with the safety fully closed . reversing sensor installed and correctly aligned : 1 . If open , the door will close , tf closed , the door will open . To open the door 2 . If closing , the door will reverse . manually : k Troley The door should be 3 . If opening , the door will stop ( allowing space for entry and exit of pets and for fresh air ) . fully closed if possible . , easeArm Pull down on the red 4 . If the door has been stopped in a partially open Trolley ! emergency release position , it will close . handle and lift the door 5 . If obstructed while closing , the door will reverse . manually . To 6 . If obstructed while opening , the door will stop . reconnect the door to Emergency 7 . The garage door will reverse in the closing cycle the opener , press the Release Handte when the invisible beam is broken , tf fully open , ( Pull Down ) Door Control push the door will not close when the beam is broken . Manual disconnect button . The sensor has no effect in the opening cycle . position If the sensor is not installed , or is not aligned The lockout feature correctly , the door won't close from any remote transmitter . You can close the door with the Door reconnecting automatically . - y Control , the Outdoor Key Switch , or Keyless Entry , prevents the trolley from _ F ' " q Pull the emergency handle / e _ ase Arm however , if you activate them until down travel is down and back ( toward the complete . If you release them too soon , the door will opener ) . The door can then TroIley j , ' _ reverse . be raised and lowered _ 11 _ , _ . , , _ ' The opener lights will blink for 5 seconds when the manually as often as safety reversing sensor causes the door to reverse . necessary . To disengage Emergency The Opener Lights will turn on under the following the Lockout Feature , pull ReIease Handte conditions : When the opener is initially plugged in ; ( Putt Down & Back the emergency handle Towards Opener ) when the power is interrupted ; when the opener is straight down . The trolley activated . They will turn off automatically after 4 - 1 / 2 will reconnect on the next Lockout position minutes or provide constant light when the Light UP or Down operation . feature on the Premium Control Console is activated . SECURITY + models : Lights will also turn on when someone walks through the open garage door . Bulb size is 75 watts maximum . Operation of the Door Controls ( see page 18 ) ( SECURITY + models : See additional programming features , next page . ) Press the lighted push button to open or close the Premium Console ( cont . ) : door . Lock Feature - The Lock feature is designed to Press again to reverse the door during the closing prevent operation of the door from remote controls . cycle or to stop the door while it's opening . However , the door will open and close from the Door Control , the Outdoor Key Switch and the Keyless Entry Premium Console : Accessories . Light Feature - Press the large round Light button . If To Activate : Press and hold the small round Lock the opener lights are off , they will turn on . If the button for 2 seconds . The push button light will flash opener lights are on , ( even in the 4 - 1 / 2 minute as long as the Lock feature is on . automatic cycle ) they will turn off To turn off . Press and hold the Lock button again But if you use the Light button to turn the lights on for 2 seconds . The push button light will stop and then activate the opener , the lights will turn off flashing . The Lock feature will also turn off whenever after 4 - 1 / 2 minutes . the " SRT " button on the opener panel is activated . The Light button will not control the opener lights when the door is in motion . 32
Page: 33

Receiver and Remote Control Programming To comply with FCC rules , adjustment or modifications of this receiver SEI IJRll and / or transmitter are prohibited , except for changing the code setting or replacing the battery THERE ARE NO OTHER USER SERVICEABLE PARTS . Your garage door opener receiver and remote control have been pre - set at the factory . The door will open when you press the LARGE remote control push button . The code between the remote control and the receiver changes with each use , randomly accessing over 100 billion new codes . Children operating or playing with a garage The 3 - function remote control can also activate door opener can injure themselves or others . The garage door could close and cause serious additional SECURITY + garage door openers and / or injury or death . Do not allow children to operate light controls . the door push button ( s ) or remote control ( s ) . Your SECURITY + opener will operate with : A moving garage door could injure or kill • several SECURITY + remote controls ( with blue someone under it . Activate the opener only push buttons ) utilizing up to 8 functions . when you can see the door clearly , it is free of • one SECURITY + Keyless Entry System ( Model obstructions , and is properly adjusted . 139.53684 ) . Follow the instructions below to program your opener Figure 1 to match any additional remotes you may purchase . See Accessories on page 38 . _ l _ < t _ rewrotecont _ puH ' _ To Add A Remote Control If you have a Premium Control Console : 1 . With the door closed , press and hold a remote 8ECURI ' IY " I " control push button . See Figure 1 . Figure 2 3 - Functien 2 . Press and hold the Light button on the door Remote ¢ onb ' ol control . SECURITY + 3 . Press and hold the door control push button . Garage Door Opener 4 . After the opener light flashes , release all buttons . Test by pressing the remote push button . If you do not have a Premium Control Console : 1 . Press and hold the selected remote control push button . See Figure 1 . " SRT " ( learn ) indicator RIGHT Button Light PANEL 2 . Then press and release the SRT ( learn ) button on the back panel of the opener , Figure 2 . The indicator light on the panel will begin to blink and To Control the Opener Light ( Premium Consoles ) the opener light will flash once . With SECURITY + remote controls , a push button can 3 . Release the remote push button . be programmed to operate the opener light without Test by pressing the remote push button . opening the door . 1 . With the door dosed , press and hold the remote To Erase All Remote Control Codes button that you want to control the light . Press and hold the SRT button on the opener panel 2 . Press and hold the Light button on the door until the indicator light turns off ( about 6 seconds ) . All control . remote control codes are now erased . Then follow 3 . Press and hold the Lock button on the door control . the steps above to re - program each remote control . 4 . After the opener light flashes , release all buttons . Test by pressing the remote push button . The opener light should turn on or off but the door should not move . 33
Page: 34

Having a Problem ? Situation Probable Cause and Solution 1 . Does the opener have electric power ? Plug a lamp into the outlet . If it doesn't light , The opener doesn't check the fuse box or the circuit breaker . ( Some outlets are controlled by a door switch . ) operate from either the Door Control or 2 . Have you disabled all door locks ? Review installation instruction warnings on Page 11 . the remote control : 3 . Is there a build - up of ice or snow under the door ? The door may be frozen to the ground . Remove any restriction . 4 . The garage door spring may be broken . Have it replaced . 5 . Repeated operation may have tripped the overload protector in the motor . Wait 15 minutes . Try again . Opener operates 1 . Is the Door Control lit ? If not , remove the bell wire from the opener terminal screws . from the remote Short the red and white terminals by touching both terminals at the same time with a control , but not from piece of wire . If the opener runs , check for a faulty wire connection at the Door the Door Control : Control , a short under the staples , or a broken wire . 2 . Are the wiring connections correct ? Review Step 6 , page 18 . . Is any door push button flashing ? If your model has the Lock feature , make sure the The door operates from the Door lock is Off . Control , but not from 2 . Your opener needs to re - learn a remote control code . Refer to Instructions on the the remote control : opener panel . 3 . Program the receiver to match the remote control code . 4 . Repeat the receiver programming procedure with all remote controls . The remote control 1 . Change the location of the remote control in your car . has short range : 2 . Check to be sure the antenna on the side or back panel of opener extends fully downward . 3 . Some installations may have shorter range due to a metal door , foil backed insulation , or metal garage siding . ( Antenna Extender Kit 41A3504 ) Opener noise is If operational noise is a problem because of proximity of the opener to the living disturbing in riving quarters , the Vibration Isolator Kit 41A3263 can be installed . This kit was designed to quarters of home : minimize vibration to the house and is easy to install . 1 . Be sure that all remote control push buttons are off . The garage door opens and closes 2 . Remove the bell wire from the Door Control terminals and operate from the remote by itself : control only . If this solves the problem , the Door Control is faulty ( replace ) , or there is an intermittent short on the wire between the Door Control and the opener . 3 . Clear memory and reprogram all remote controls . The door doesn't 1 . Is something obstructing the door ? Remove the obstruction or repair the door . open completely : 2 . If the door has been working properly but now doesn't open all the way , increase the up force . See page 29 . 3 . If door opens at least 5 feet , the travel limits may need to be increased . One turn equals 2 inches of travel . See page 28 . Repeat the safety reverse test after the adjustment is complete . The door stops but Review the travel limits adjustment procedures on page 28 . doesn't close Repeat the safety reverse test after any adjustment of door arm length , close completely : force or down limit . 34
Page: 35

Having a Problem ? ( continued ) Situation Probable Cause & Solution The door opens but 1 . If the opener lights blink , check the safety reversing sensor . See page 23 . won't close : 2 . If the opener lights do not blink and it is a new installation , check the down force . See Adjustment Step 2 , page 29 . For an existing installation , see below . Repeat the safety reverse test after the adjustment is complete • The door reverses for 1 . Is something obstructing the door ? Pull the red emergency release handle . Operate no apparent reason the door manually . If it is unbalanced or binding , call for professional garage door service . and opener lights don't blink : 2 . Clear any ice or snow from the garage floor area where the door closes . 3 . Review the force adjustment procedures on page 29 . 4 . If door reverses in the fully closed position , decrease the travel limits ( page 28 ) . Repeat safety reverse test after adjustments to force or travel limits • The need for occasional adjustment of the force and limit settings is normal Weather conditions in particular can affect door travel The door reverses for Check the safety reversing sensor . Remove any obstruction or align the receiving eye . no apparent reason See page 23 . and opener nlightsds blink for 5 seco after reversing : The opener lights : • . . don't turn on : Replace the light bulbs ( 75 watts maximum ) . Use a standard neck garage door opener bulb if regular bulb burns out . • . . don't turn off : Is the Light feature on ? Turn it off The door may be out of balance or the springs are broken . Close the door and use the The opener strains or maximum force is emergency release to disconnect the trolley . Open and close the door manually . A properly needed to operate balanced door will stay in any point of travel while being supported entirely by its springs , tf it door : does not , disconnect the opener and call a professional garage door serviceman . Do not increase the force to operate the opener . The opener motor 1 . The garage door springs are broken . See above . hums briefly , then 2 . If the problem occurs on the first operation of the opener , door may be locked . Disable won't work : the doorlock . If the chain was removed and reinstalled , the motor may be out of phase . Remove the chain ; cycle the motor to the down position . Observe the drive sprocket . When it turns in a clockwise direction and stops in the down position , reinstall the chain . Repeat the safety reverse test after the adjustment is complete •
Page: 36

Repair Parts 7 DESCRIPTION Master link kit 2 41A3489 Complete trolley assembly 3 1B3117 T - rail - center section 4 183Bl10 T - rail - end section 5 41B2616 Cable pulley bracket assembly 6 41A3473 Chain and cable 7 83A4 Rail grease NOT SHOWN 41A3534 Rail assembly hardware kit ( includes hardware illustrated on page 7 ) . 3 / 9 4 Installation _ 1Parts _ ) _ _ 8 / _ 0 i KEY PART _ 1 NO , NO . DESCRIPTION 1 1 41A4884 Premium control console 2 41A5032 3 - function remote control housing 3 10A19 3V 2016 Lithium battery ( 2 required ) 1 3 4 29B134 Visor clip / 2 5 31D431 Keyless entry keypad cover ( no circuit board ) _ _ - _ \ _ X O1 6 31B430 Keyless entry battery cover 7 10A2 12Volt battery 8 41A2828 Emergency rope & handle assembly 9 41A4353 Header bracket w / clevis pin & fastener 10 217A238 2 - conductor bell wire - white & white / red 17 11 178B35 Curved door arm section 14 12 41A5047 Door bracket w / clevis pin & fastener 18 13 41A4373A Safety sensor kit ( receiving and sending eyes ) with 3 ' 2 - conductor bell wire attached 1 5 14 12B483 " C " Wrap Bracket _ . . _ / 15 12B484 Square Hole Bracket 16 12B485 Slotted Bracket 17 12B350 Hanging brackets 18 178B34 Straight door arm section 41A3475 - 4 Installation hardware bag ( includes hardware NOT SHOWN illustrated on page 7 ) . 16 J 41A4116 Safety sensor hardware 114A2122 Owner's manual 36
Page: 37

Repair Parts Opener Assembly Parts I 5 20 8 19 18 13 5 17 _ _ 14 ( Down ) LIMIT SWITCH 16 Btown Contact ASSEMBLY Contact Contact Wire KEY PART KEY PART NO . NO . DESCRIPTION NO . NO . DESCRIPTION 1 31D380 9 108D48 - 2 Lens Sprocket cover 2 41 C4220A 10 30B363 Gear and sprocket assembly Capacitor - 1 / 2HP Complete with : 11 12A373 Capacitor bracket Spring washer 12 41A3150 Terminal block w / screws Thrust washer 13 41D3058 Universal replacement motor & Retaining ring bracket assembly Bearing plate Complete with : Motor , worm , Roll pins ( 2 ) bracket , bearing assembly , Drive gear and worm gear RPM sensor Helical gear w / retainer and grease 14 41D0328 - 7 Cover 41A2817 Drive / worm gear kit w / grease 15 41A2818 Helical gear & retainer w / grease Roll pins ( 2 ) 16 41D3452 Limit switch assembly 4 41 B4245 Line cord 17 41C4398A RPM sensor assembly 5 41C4253 Wire harness assembly w / plug 18 41A2826 Shaft bearing kit 6 41A5021 - 2 Receiver logic board assembly 19 41A2822A Interrupter cup assembly Complete with : Logic board 20 41A4352 End panel End panel w / all labels NOT SHOWN 7 41A4351 End panel w / all labels 41A2825 Opener assembly hardware kit 8 175B88 Light socket ( includes screws not designated by a number in illustration ) . 37
Page: 38

Accessories Sears offers many useful accessories for your garage door opener . They are illustrated below with Sears model numbers and descriptions . 139.53702 139.53681 SECURITY + 3 - Function Remote Emergency Key Release : Control : Required for a garage with NO Includes visor clip . access door . Enables homeowner to open garage door manually from / outside by disengaging trolley . 139.53680 SECURITY + Compact 139.53703 Outdoor Key Switch : 3 - Function Remote Control : Operates the garage door With loop for attaching key ring . automatically from outside when ( Available April , 1997 ) remote control is not handy . 139.53684 SECURITY + Keyless Entry : Enables homeowner to operate garage 139.53704 8 Foot Rail Extension door opener from outside by entering a password . Also can add a temporary To allow an 8 foot door to open fully password for visitors or service persons . This temporary password can be limited to a programmable number of hours or entries . 139.53705 10 Foot Rail Extension : 139.53686 Plug - In Light Control : Enables homeowner to turn on a To allow a 10foot door to open fully . lamp , television or other appliance from car , bedside , or anywhere in the home with a remote . ( Available April , 1997 ) 139.53709 Door Clearance Brackets : 53885 Support Brackets : ( For Sectional Doors Only ) For finished ceilings or where Replaces top brackets and rollers on additional support is required , door to reduce height of door travel . based on garage construction . For use when installing opener in Includes brackets and fastening hardware . garage with low headroom clearance . To Add the Keyless Entry We recommend that you program your password If you do not have a Premium Control Console : before you install the Keyless Entry . You will not 1 . Choose a 4 - digit password using numbers from need assistance , and you can test the reception at 0 to 9 ( a number can be used more than once , for the mounting location before installation . example , 4 , 0 , 4 , 1 ) . If you have a Premium Control Console : 2 . Press the four buttons for the password , then press and hold the Enter button . The indicator light on 1 . With the door closed , press the four digit password the door opener panel will blink . desired , then press and hold Enter . 3 . Press and release the SRT ( learn ) button on the 2 . Press and hold the light button on the door control . opener panel . After the opener light flashes , 3 . Press and hold the door control push bar . release the Enter button . 4 . After the opener light flashes , release all buttons . Test by pressing the password , then press Enter . The door should begin to move . 38
Page: 39

Index Chain Tension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 , 5 , 11 Electrical Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 , 20 , 31 Garage Door Testing for balance , binding and sticking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 , 28 , 31 Determining high point of travel : Sectional door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 One - piece door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Disabling existing locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 , 11 Door clearance brackets ( for garages with low headroom ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Force controls Adjustment procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 , 29 Problems that might require force adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 , 35 Safety warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 , 31 Door hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 , 9 , 11 , 12 , 18 , 31,32 Maintenance instruction label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 , 28 Reinforcement requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 , 24 Removing of all ropes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 , 11 Possible door damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 , 24 Travel limits Adjustment procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Problems that might require limit adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 , 35 Safety warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 , 31 Manual ( Emergency ) Release Rope & Handle Lockout feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Manual disconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Safety warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 , 19 , 31,32 Opener Terminals Door control connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Safety reversing sensor connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Operational Noise Sprocket noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Vibration noise ( isolator kit ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Receiver and Remote Control Programming the receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Erasing all codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Activating other openers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Safety warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Problems with remote control operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Safety Reverse Test Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Testing required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11,30 , 34 , 35 Safety reverse system problems Securing header bracket to wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Adjusting travel limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Applying excessive force on the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Buckling or uneven floor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 , 5 Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 , 3 , 9 , 11 , 12 , 16 , 18 , 19 , 20 , 21 , 24 , 28 , 29 , 30 , 31 , 32 , 33 User Instruction Label for garage wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 , 18 39
Page: 40

For professional installation Call 24 hours a day , 7 days a week 1 - 800 - 865 - 6500 For the repair or replacement parts you need Call 7 am - 7 pm , 7 days a week 1 - 8OO - 366 - PART ( 1 - 800 - 366 - 7278 ) For in - home major brand repair service Call 24 hours a day , 7 days a week 1 - 800 - 4 - REPAI R ( 1 - 800 - 473 - 7247 ) For the location of a Sears Repair Service Center in your area Call 24 hours a day , 7 days a week 1 - 800 - 488 - 1 222 For information on purchasing a Sears Maintenance Agreement or to inquire about an existing Agreement Call 9 am - 5 pm , Monday - Saturday 1 - 800 - 827 - 6655 The model number label is located under the light lens on the front end panel of your opener . When requesting service or ordering parts , always give the following information : * Part Number * Product Type * Model Number * Part Description America's Repair Specialists SEARS WARRANTY FULL 90 - DAY WARRANTY ON GARAGE DOOR OPENER For 90 days from the date of purchase , Sears will repair this Garage Door Opener , free of charge , if defective in material or workmanship . LIMITED WARRANTY From the 91 st day until one year from the date of purchase , Sears wilt furnish replacement parts for any defective parts , free of charge . You pay for labor . LIMITED WARRANTY ON MOTOR I / 2HP MOTOR : After 1 year and through 5 years , if the motor on this Garage Door Opener is defective , Sears wilt furnish a replacement motor , free of charge . You pay for labor . LIMITATION ON LIABILITY SEARS WILL NOT BE LIABLE FOR LOSS OR DAMAGE TO PROPERTY OR ANY INCIDENTAL OR CONSEQUENTIAL LOSS OR EXPENSE FROM PROPERTY DAMAGE DUE DIRECTLY OR INDIRECTLY FROM THE USE OF THIS PRODUCT . Some states do not allow the exclusion or limitation of incidental or consequential damages , so the above limitation or exclusion may not apply to you . This warranty does not cover light bulbs or repair parts necessary because of operator abuse or negligence , including the failure to install , adjust and operate this garage door opener according to instructions contained in the owner's manual . WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS CENTER / DEPARTMENT IN THE UNITED STATES . This warranty applies only while this product is in use in the United States . This warranty gives you specific legal rights , and you may also have other rights which vary from state to state . Sears , Roebuck and Co . , Dept . 817WA , Hoffman Estates , IL 60179 114A2122D © 1997 , All Rights Reserved Printed in Mexico
Search in Garage Door Opener on ebay
"