Home | Register Login | Wanted Manuals | MarketPlace | Members Area | Manuals Manufacturer Directory | UPC Lookup | Information Pages | Policy


Back To Craftsman Garage Door Opener       Model: 139.53776 or 13953776 Craftsman Garage Door Touch Code Transmitter
Regular Text Search or Search by Model Number

Register / log-in to add to your Hammerwall Collection.
Manual Location

Videos About This Item
Loading...

This is a partial text extraction from the pdf, to download the pdf, click the Manual tab. If you want to search this text, hold control and F, and type the word you are looking for.

Page: 1

TOUCH CODE TRANSMITTER MODEL 139.53776 OWNERS MANUAL FCC . rules prohibit adfustments to or modification of receiver and transmitter circuitry except for changing the code setting and replacing the transmitter battery . THERE ARE NO OTHER USER SERVICEABLE PARTS . Manufactured under " 1 _ m _ e of the following U S . patents : RE29 , . 525 ; 4,037 " , 201 ; 4,750,118 ; 4,806,930 FEATURES OF THE TOUCH CODE TRANSMITTER Personalized Code : Upto 10,000 possible combinations , Keypad will Illuminate for 10 seconds at the first push of Code can easily be changed if desired . ANY number key , Keypad will remain illuminated for 20 seconds after code Operation : Opener activates when programmed code is keyed into transmitter and ENTER button is pressed , is transmitted ° During that time you can STOP or REVERSE door travel just by pressing the ENTER key . The user has 10 seconds to key in the 4 - digit code and Power Supply : 12Volt battery . press the ENTER button . tf wrong numbers are accidentally pressed , correction can Installation : Simple to install , Fastening screws and plug be made immediately . The ENTER key will transmit only are provided _ the last four digits ° All 53000SR Sedes Receivers have two memory channels ; This transmitter can be used with any 5B000SR Series one for the Touch Code Transmitter and the other for all garage door opener and / or Light Control . portable transmitters used to operate an opener or to turn on lights . INSTALL TRANSMITTER Open the transmitter cover and remove the battery compartment screw . Set cover aside and remove battery . NOTE BATTERY POLARITY AS MARKED ON COMPARTMENT Follow the mounting instructions which apply to your type of door as described below . NOTE : If you want the transmitter ' in a location different from the one illustrated , it is recommended that you program the code into the receiver and test the operation of the transmitter before mounting it . A metal door , foil - backed insula - lion or aluminum siding will lessen transmission range . ON _ = - PIECE DOOR INSTALLATION : Install the SECTIONAL DOOR INSTALLATION : Center the trans - mitter on garage jamb face at eye level as shown ( Figure 1 ) . transmitter on exterior front wall of a FRAME garage . Be sure to position it away from the door opening to avoid injury as Hold the transmitter firmly against jamb with cover half open door swings out and up ( Figure 2 ) . NOTE : If the garage is so both top and bottom mounting holes are visible _ Use a constructed of material other than wood ( brick , stone or punch to mark each hole . Drill two 1 / 8 " pilot holes , Fasten aluminum siding ) , install transmitter on door jamb with transmitter securely with screws provided . this important exception : LOCATE TRANSMITTER ON insert the plug provided into top hoTe to cover the fastening OUTSIDE EDGE OF DOOR JAMB TO AVOID INJURY AS screw . W l'len installing the battery , be sure to observe DOOR SWINGS OUT AND UP . polarity ( refer to illustration ) , Re - fasten compartment Mark fastening holes , drilt and install the transmitter as cover . instructed for sectional door _ NOTE BATTERY POLARITY . FIGURE t FIGURE 2 Keyboard Garage ! b Side 1
Page: 2

SETTING THE CODE 1 . Open the Touch C . ode Transmitter cover to access the key - pad . Decide on a 4 - digit code number using numbers from 0 to 9 . You can use a number more than once . ( For example , 4 , 0 , 4 , 1 ) . 2o Press the ' SR ' code button on the opener panel . The indicator light atongside the push button will turn ON . 3 _ STAND AWAY FROM THE DOOR . Press the selected code numbers on the keypad and then press the ENTER key . The indicator light on the opener panel wiil turn OFF and the door witl begin to move , The opener receiver has been . _ programmed with your code selection . ( _ NOTE 1 " If the indicator light turns OFF before the code _ . " _ _ ' digits and ENTER key are pressed , repeat Steps 2 and 3 . _ . _ t , _ - _ J t _ NOTE 2 ' During programming , be sure the , k / _ ca _ i _ n push : - - - ' - " _ " button ( if your opener has that feature ) is OFF and the Infrared Sensor ( if you have installed that accessory ) isE free of obstruction . THE DOOR WILL NOT MOVE AND TH INDICATOR LIGHT WILL NOT TURN OFF in either case . To change your code at any time , repeat Steps 1 , 2 and 3 . T BATTERY : The 12 Volt battery should produce power for at least one year . As long as there is adequate power , the key - pad will illuminate and receiver will operate when code and ENTER keys are pressed . Replace the battery when keypad illumination becomes dim . GARAGE DOOR OPENER RECEIVER 0 & _ " SR ' Code Button ) RED WHT BLK YEL % " 1989 , Sears Roebuck & Company 114At155 All Rights Reserved Printed in Mexico
Page: 3

SEARS MOOEL ! 39.53776 TOUCH CODE TRANSMITTER PARTS LIST 12 Volt Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10A14 NO OTHER USER SERVICEABLE PARTS
Search in Garage Door Opener on ebay
"