Home | Register Login | Wanted Manuals | MarketPlace | Members Area | Manuals Manufacturer Directory | UPC Lookup | Information Pages | Policy


Back To Craftsman Table Saw       Model: 152.221040 or 152221040 Craftsman 2 HP 3450 RPM 10 Inch Table Saw
Regular Text Search or Search by Model Number

Register / log-in to add to your Hammerwall Collection.
Manual Location


This is a partial text extraction from the pdf, to download the pdf, click the Manual tab. If you want to search this text, hold control and F, and type the word you are looking for.

Page: 1

Owner's Manual CRRFr MRH 1.5 Horsepower ( continuous duty ) 2 Horsepower ( maximum developed ) 3450 R . P . M . ( no load R . P . M . ) 10 - in . LE SAW Model No . 152.221040 Customer Helpline 1 - 800 - 897 - 7709 CAUTION : Please have your Model No . and Serial No . available . FOR YOUR OWN SAFETY ; Read and follow all of the Safety and Operating Instructions before Operating this Table Saw . Sears , Roebuck and Co . , Hoffman Estates , IL 60179 U . S . A . Part No . OR91550 Revision : D EspaRolpg . 45
Page: 2

SECTION PAGE Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guidelines for Extension Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Grounding instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Specific Safety instructions for Table Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Accessories and Attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Carton Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Know Your Table Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Assembly instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Operations and Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Part List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Espanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Service information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 FULL ONE YEAR WARRANTY If this product fails due to a defect in material or workmanship within one year from the date of purchase , return it to the nearest Sears Service Center for repair , free of charge . If this product is used for commercial or rental purposes , this warrant y applies only for 90 days from date of purchase . This warranty gives you specific legal dghts , and you may also have other dghts , which vary , from state to state . Sears , Roebuck and Co . , Dept 817 WA , Hoffman Estates , IL 60179 Table in front of blade at max Motor type Induction 12 - 1 / 2 - in . depth - of - cut Continuous duty HP 1.5 Max dado width 13 / 16 - in . Maximum developed HP 2 Max . dado blade diameter 8 - in . Amps 15 / 7.5 Left and right table wing 8 - in , Stamped Steel Volts 120 / 240 350 Ibs . Weight of table saw Hertz 60 RPM 3450 R . P . M . ( no load R . P . M . ) Blade tilt Left tilt Blade drive Poly - V Belt Blade diameter 10 - in . To avoid electrical shock to yourself and damage to the Blade arbor 5 / 8 - in . Table Saw , use proper circuit protection . Do not expose to rain , or use in a damp environment . Number of teeth 40 Blade speed 3450 R . P . M . The Table Saw is factory wired for 120V , 60 Hz , operation . Fence type Front locking , Extruded Connect to a 120V , 15 amp branch circuit and use a 15 aluminum Fence and Rails amp time delay fuse or circuit breaker . The electrical circuit Max depth - of - cut at 90 - degree 3 - 3 / 8 - in . cannot have any wire size less than # 14 . To avoid shock Max depth - of - cut at 45 - degree 2 - 1 / 4 - in . or fire , replace power cord immediately if it is damaged in Max rip to the right of the blade 25 - in . any way . Max rip to the left of the blade 12 - in .
Page: 3

Anti - KickbacFkingers - Asafetydeviceattachedtothe Kerf - Themateriarlemovebdythebladeinthework - bladeguardandsplittear ssembldyesignetdostopa pieceduringanycuttingoperation . workpiecferombeingthrownbackduringacuttingopera - tion . Kickback - Whentheworkpieciesthrownbacktowards theoperatodruringa cuttingoperatiownhentheworkpiece Arbor - Theshaftonwhichthebladeoraccessorcyut - initiallycontactsthebladeorif theworkpiecpeinchetshe ting - tooisl mounted . bladeK . ickbaciksdangerouasndcanresulitnserious injury . BevelCut - Theoperatioonfmakinganycutwiththe bladesetonadegreeotherthan90degrees . MiterCut - Theoperatioonfmakingacutusingthemiter gaugeatanyangleotherthanzerodegrees . CompoundCut - Theoperatioonfmakingbotha bevel anda mitercutatonetime . PushStick - Anaccessordyevicethatcanbemadeor purchasetdohelppushtheworkpiectehroughtheblade . Apushstickisusedtokeeptheoperator'hsandsaway Crosscu - t Theoperatioonfmakingacutacrossthe fromthebladewhenrippinganarrowworkpiece . grainorwidthofaworkpiece . Rabbe - t Asquarenotchintheedgeoftheworkpiece . Dado - Anon - througchutthatproduceassquarenotch . A dadoistypicallyfrom1 / 8 - int . o 13 / 16 - inw . ide . Adado requireasspeciasletofbladesn , otincludewd iththis Resaw - Theoperatioonfmakingacuttoreducethe tablesaw . thicknesosftheworkpiece . RipCut - Theoperatioonf makingacutwiththegrainof Featherboar - dAnaccessordyevicethatcanbemadeorg purchasetdohelpguideorholddownaworkpiecdeurin theworkpiece . cuttingoperations . SawBladePath - iTheareathatisdirectlyinlinewiththet . Freehand - Averydangerouosperatioonfmakingacut bladei , ncludinagreaover , underb , ehindandinfrontof withouutsingthefenceormitergaugeinacuttingopera - tion . FreehancdutsmustneverbeperformeodnaTable Saw . Setof theSawBlade - Thedistanctehatthetipsofthehe sawbladeareangledoutwardfsromthethicknesosft blade . Thesetofthesawbladeteethallowsfortheblade Gum , Pitchor Resin - Astickys , apbasedresiduethat bodytopasssafelythroughallcuts . comesfromwoodproducts . Table / WorAkrea - Thetotalsurfaceofthetopofthetable Hee - l Themisalignmeonftthebladetothemiterslots ; sawonwhichtheworkpiecreestswhileset - uporcutting whenthebladeisnotparalletlothemiterslots . operationasrebeingperformed .
Page: 4

9 . GENERAL SAFETY INSTRUCTIONS ALWAYS WEAR EYE PROTECTION . Any power tool can throw debris into the eyes during opera - Operating a Table Saw can be dangerous if safety and tions , which could cause severe and permanent common sense are ignored . The operator must be eye damage . Everyday eyeglasses are NOT safety familiar with the operation of the tool . Read this manual glasses . ALWAYS wear Safety Goggles ( that to understand this Table Saw . DO NOT operate this comply with ANSi standard Z87 . t ) when operating Table Saw if you do not fully understand the limitations power tools . Safety Goggles are available at Sears of this tool . DO NOT modify this Table Saw in any way . Retail Stores . Hearing equipment should comply REMEMBER : Your personal safety is your with ANSi S3 . t 9 Standards . responsibility . BEFORE USING THE TABLE SAW To avoid serious injury and damage to the tool , read and follow all of the Safety and Operating Instructions 10 . ALWAYS UNPLUG THE TOOL FROM THE ELEC = before operating the Table Saw . TRICAL RECEPTACLE when making adjustments , changing parts or performing any maintenance . 1 . READ the entire Owner's Manual . LEARN how to use the tool for its intended applications . 11 . KEEP PROTECTIVE GUARDS iN PLACE AND iN WORKING ORDER . 2 . GROUND ALL TOOLS . If the tool is supplied with a 3 - prong plug , it must be plugged into a 3 - contact 12 . AVOID ACCIDENTAL STARTING . Make sure that electrical receptacle . The 3rd prong is used to the power switch is in the " OFF " position before plug - ground the tool and provide protection against ging in the power cord to the electrical receptacle . accidental electric shock . DO NOT remove the 3rd prong . See Grounding Instructions . 13 . REMOVE ALL MAINTENANCE TOOLS from the immediate area prior to turning the tool " ON " . 3 . AVOID A DANGEROUS WORKING ENVIRON = MENT . DO NOT Use electrical tools in a damp 14 . USE ONLY RECOMMENDED ACCESSORIES . environment or expose them to rain . Use of incorrect or improper accessories could cause serious injury to the operator and cause 4 . DO NOT use electrical tools in the presence of damage to the tool . If in doubt , check the instruction flammable liquids or gasses . manual that comes with that particular accessory . 5 . ALWAYS keep the work area clean , well lit , and 15 . NEVER LEAVE A RUNNING TOOL UNATTENDED . organized . DO NOT work in an environment with Turn the power switch to the " OFF " position . DO floor surfaces that are slippery from debris , grease , NOT leave the tool until it has come to a complete and wax . stop . 6 . KEEP ViSiTORS AND CHILDREN AWAY from the 16 . DO NOT STAND ON A TOOL . Serious injury could table saw . DO NOT permit people to be in the result if the tool tips over or you accidentally contact immediate work area , especially when the electrical the tool . tool is operating . 17 . DO NOT store anything above or near the tool 7 . DO NOT FORCE THE TOOL to perform an opera - where anyone might try to stand on the tool to tion for which it was not designed . It will do a safer reach it . and higher quality job by only performing operations for which the tool was intended . 18 . MAiNTAiN YOUR BALANCE . DO NOT extend yourself over the tool . Wear oil resistant rubber - 8 . WEAR PROPER CLOTHING . DO NOT wear loose soled shoes . Keep floor clear of debris , grease , clothing , gloves , neckties , or jewelry . These items and wax . can get caught in the machine during operations and pull the operator into the moving parts . Users 19 . MAiNTAiN TOOLS WITH CARE . Always keep tools must wear a protective cover on their hair , if the clean and in good working order . Keep all blades hair is long , to prevent it from contacting any mov - and tool bits sharp . ing parts .
Page: 5

20 . EACHAND EVERY TIME , CHECK FOR DAM = GUIDELINES FOR AGED PARTS PRIOR TO USING THE TOOL . EXTENSION CORDS Carefully check all guards to see that they operate properly , are not damaged , and perform their The smaller the gauge - number , the larger diameter of intended functions . Check for alignment , binding or the extension cord . If in doubt of the proper size of an breaking of moving parts . A guard or other part that extension cord , use a shorter and thicker cord . An is damaged should be immediately repaired or undersized cord will cause a drop in line voltage result - replaced . ing in a loss of power and overheating . USE ONLY A 3 - WIRE EXTENSION CORD THAT HAS A 3 - PRONG 21 . CHILDPROOF THE WORKSHOP AREA by remov - GROUNDING PLUG AND A 3 - POLE RECEPTACLE ing switch keys , unplugging tools from the electrical THAT ACCEPTS THE TOOL'S PLUG . receptacles , and using padlocks . If you are using an extension cord outdoors , be sure it 22 . DO NOT OPERATE TOOL iF UNDER THE is marked with the suffix " W - A " ( " W " in Canada ) to indi - iNFLUENCE OF DRUGS OR ALCOHOL . cate that it is acceptable for outdoor use . 23 . SECURE ALL WORK . When it is possible , use Be sure your extension cord is properly sized , and in clamps or jigs to secure the workpiece . This is safer good electrical condition . Always replace a damaged than attempting to hold the workpiece with your extension cord or have it repaired by a qualified person hands . before using it . 24 . STAY ALERT , WATCH WHAT YOU ARE DOING , Protect your extension cords from sharp objects , exces - AND USE COMMON SENSE WHEN OPERATING sive heat , and damp or wet areas . A POWER TOOL . DO NOT USE A TOOL WHILE TIRED OR UNDER THE iNFLUENCE OF DRUGS , ALCOHOL , OR MEDICATION . A moment of inattention while operating power tools may result 120 VOLT OPERATION ONLY in serious personal injury . 25 ' LONG 50 ' LONG 100 ' LONG 18 AWG 16 AWG 16 AWG 0 to 6 Amps 25 . Use of this tool can generate and disburse dust or other airborne particles , including wood dust , 18 AWG 16 AWG 14 AWG 6 to 10 Amps crystalline silica dust and asbestos dust . Direct 16 AWG 16 AWG 14 AWG 10 to 12 Amps particles away from face and body . Always operate 14 AWG 12 AWG Not 12 to 15 Amps tool in well ventilated area and provide for proper recommended dust removal . Use dust collection system wherever possible . Exposure to the dust may cause serious and permanent respiratory or other injury , including silicosis ( a serious lung disease ) , cancer , and death . Avoid breathing the dust , and avoid pro - 240 VOLT OPERATION ONLY longed contact with dust . Allowing dust to get into your mouth or eyes , or lay on your skin may 25 ' LONG 50 ' LONG 100 ' LONG promote absorption of harmful material . Always use properly fitting NIOSH / OSHA approved respiratory 18 AWG 18 AWG 16 AWG 0 to 6 Amps protection appropriate for the dust exposure , and 18 AWG 18 AWG 14 AWG 6 to 10 Amps wash exposed areas with soap and water . 16 AWG 16 AWG 14 AWG 10 to 12 Amps 26 . USE A PROPER EXTENSION CORD iN GOOD 14 AWG 12 WG Not 12 to 15 Amps recommended CONDiTiON . When using an extension cord , be sure to use one heavy enough to carry the current your product will draw . Please see " MiNiMUM RECOMMENDED GAUGE FOR EXTENSION CORDS ( AWG ) " table for correct sizing of an extension cord . If in doubt , use the next heavier gauge . 27 . DiRECTiON OF FEED . Feed work into a blade or cutter against the direction of rotation of the blade or cutter only .
Page: 6

THIS TOOL MUST BE GROUNDED WHILE IN USE USE ONLY A 3 = WIRE EXTENSION CORD THAT HAS TO PROTECT THE OPERATOR FROM ELECTRIC A 3 = PRONG GROUNDING PLUG AND A 3 - POLE SHOCK . RECEPTACLE THAT ACCEPTS THE TOOL'S PLUG . IN THE EVENT OF A MALFUNCTION OR BREAK - REPLACE A DAMAGED OR WORN CORD IMMEDI = ATELY . DOWN , grounding provides the path of least resistance for electric current and reduces the risk of electric FOR GROUNDED , CORD = CONNECTED MACHINES shock . This tool is equipped with an electric cord that iNTENDED FOR USE ON A SUPPLY CiRCUiT HAVING has an equipment - grounding conductor and a ground - A NOMINAL RATING LESS THAN 150 VOLTS . ing plug . The plug MUST be plugged into a matching This tool is intended for use on a circuit that has an electrical receptacle that is properly installed and grounded in accordance with ALL local codes and electrical receptacle as shown in FIGURE " IA ' . ordinances . FIGURE " IA " shows a 3 - wire electrical plug and elec - trical receptacle that has a grounding conductor . If a DO NOT MODIFY THE PLUG PROVIDED . If it will not properly grounded electrical receptacle is not available , fit the electrical receptacle , have the proper electrical an adapter as shown in FIGURE " IB " can be used to receptacle installed by a qualified electrician . temporarily connect this plug to a 2 - contact ungrounded receptacle . The adapter has a rigid lug extending from it IMPROPER ELECTRICAL CONNECTION of the equip - that MUST be connected to a permanent earth ground , ment - grounding conductor can result in risk of electric such as a properly grounded receptacle box . THIS ADAPTER IS PROHiBiTED iN CANADA . shock . The conductor with the green insulation ( with or without yellow stripes ) is the equipment - grounding CAUTION : In all cases , make certain the electrical conductor . DO NOT connect the equipment - grounding conductor to a live terminal if repair or replacement of receptacle in question is properly grounded . If you are not sure have a certified electrician check the electrical the electric cord or plug is necessary . receptacle . CHECK with a qualified electrician or service personnel if you do not completely understand the grounding The motor supplied with your Table Saw is a dual volt - instructions , or if you are not sure the tool is properly age , 120 / 240 volt , single phase motor . If it is desired grounded . to operate your table saw at 240 volts , it is necessary to reconnect the motor leads in the motor junction box by The motor supplied with your Table Saw is a dual voltage following the wiring diagram on the junction box cover . 120 / 240 volts , 60 hertz alternating current , single phase motor . It is shipped wired for 120 volts application . Never connect the green or ground wire to a live terminal . MAKE CERTAIN the motor is disconnected from power source before reconnecting motor leads . Fig . 1A Fig . 1B grounding adapter lug 120 VOLT 120 VOLT grounding conductor grounding conductor electrical receptacle 2 - prong electrical 3 - wire electrical cord 3 - wire electrical cord receptacle
Page: 7

It is also necessary to replace the 120 volt plug , sup - MAKE CERTAIN that masks or respirators are plied with the motor , with a UL / CSA Listed plug suitable MSHA / NIOSH approved . for 240 volts and rated current of the saw . Contact a The operation of any Table Saw can result in debris local qualified electrician for proper procedures to install being thrown into your eyes , which can result in severe the plug . The table saw must comply with all local and eye damage . ALWAYS wear Safety Goggles ( that com - national electrical codes after the 240 volt plug is ply with ANSi standard Z87 . 1 ) when operating the Table installed . Saw . Safety Goggles are available at Sears Retail The table saw with a 240 volt plug should only be con - Stores . Keep your thumbs and fingers away from the nected to an outlet having the same configuration as blade while it is spinning . the plug shown in Figure " 1C " . No adapter is available or should be used with the 240 volt plug . Fig . 1 C grounded outlet box current Basic precautions should always be followed when 240 VOLT carrying using your Table Saw . To reduce the risk of injury , prongs electrical shock or fire , comply with the safety rules listed below : © 1 . READ and understand the instruction manual e before operating the Table Saw . 2 . DO NOT OPERATE THiS MACHINE until it is assem - © bled and installed according to the instructions . grounding blade is 3 . OBTAIN ADVICE FROM YOUR SUPERVISOR , longest of the 3 blades instructor , or another qualified person if you are not familiar with the operation of this machine . 4 . DO NOT leave the Table Saw plugged into the elec - trical outlet . Unplug Table Saw from the outlet when not in use and before servicing , changing blades MAKE CERTAIN the receptacle in question is properly grounded . If you are not sure have a qualified electri - and cleaning . cian check the receptacle . 5 . ALWAYS turn the power switch " OFF " before unplugging the Table Saw . 6 . TO REDUCE THE RISK OF ELECTRICAL This Table Saw is for indoor use only . Do not expose to SHOCK , do not use outdoors . Do not expose to rain or use in damp locations . rain . Store indoors . 7 . FOLLOW all electrical and safety codes , including SPECIFIC SAFETY INSTRUCTIONS the National Electric Code ( NEC ) and the FOR TABLE SAWS Occupational Safety and Health Regulations ( OSHA ) . All electrical connections and wiring should CALIFORNIA PROPOSITION 65 be made by qualified personnel only . 8 . DO NOT handle the plug or Table Saw with wet hands . SOME DUST CREATED BY POWER SANDING , 9 . USE only as described in this manual . USE acces - SAWING , GRINDING , DRILLING AND OTHER CON = sories only recommended by Sears . STRUCTION ACTiViTiES contains chemicals known to 10 . DO NOT pull the Table Saw by the power cord . cause cancer , birth defects or other reproductive harm . NEVER allow the power cord to come in contact Some examples of these chemicals are : with sharp edges , hot surfaces , oil or grease . • lead from lead - based paints , 11 . DO NOT unplug the Table Saw by pulling on the • crystalline silica from bricks and cement and other power cord . ALWAYS grasp the plug , not the cord . masonry products , and 12 . REPLACE a damaged cord immediately . DO NOT • arsenic and chromium from chemically - treated lumber . use a damaged cord or plug . If the Table Saw is not Your risk from these exposures varies , depending on operating properly , or has been damaged , left out - how often you do this type of work . To reduce your doors or has been in contact with water , return it to exposure to these chemicals : work in a well ventilated a Sears Service Center . area , and work with approved safety equipment , such 13 . DO NOT use the Table Saw as a toy . DO NOT use as those dust masks that are specially designed to filter near or around children . out microscopic particles .
Page: 8

14 . TheTableSawisdesignedforhomeuseorlight 27 . NEVERperformlayouta , ssemblyorset - gupworkon . commerciadlutyONLY . thetable / worakreawhenthemachineis runnin 28 . NEVER reset the thermal - overload button before 15 . CONNECTTableSawtoa properlygroundedoutlet only . Seegroundinginstructions . you have turned the table saw " OFF " . 29 . 16 . ALWAYSUSEtheguardswheneveprossible . PROPERLY SUPPORT long or wide workpiece . Checktoseethattheyareinplace , securedand 30 . TURN THE SAW " OFF " and unplug from power workingcorrectly . source . Clean off the table / work area before leav - 17 . AVOIDKICKBACKby : ing the saw . LOCK the START / STOP switch with padlock provided to prevent unauthorized use . • Keepingbladesharpandfreeof rustandpitch . • Keepingripfenceparalletlo sawblade . 31 . ALWAYS position auxiliary fence at least 2 - inches • Usingsawbladeguardandsplitterassemblyfor - in front of saw blade when using auxiliary fence as everypossibleoperationi , ncludingallthrough a stop when cross cutting . sawing . 32 . The right extension wing MUST BE completely • Pushingtheworkpiecepastthesawbladepriorto assembled and motor cover closed and fastened release . before table saw is to be connected to the power • Neverripaworkpiecethatis twistedorwarped , source . ordoesnothavea straighet dgetoguidealong thefence . 33 . ADDiTiONAL iNFORMATiON regarding the safe • Usingfeatherboardwshenthebladeguardand and proper operation of this product is available splitterassemblycannotbeused . from the National Safety Council , 1121 Spring Lake Neversawinga largeworkpiecethatcannotbe Drive , Itasca , IL 60143 - 3201 in the Accident controlled . Prevention Manual for Industrial Operation and also in the Safety Data Sheets provided by the NSC . Neverusingthefenceasaguidewhencross - Please also refer to the American National cutting . Standards Institute ANSi 01.1 Safety Requirements • Neversawingaworkpiecewithlooseknotsor for Woodworking Machinery and the U . S . otherflaws . Department of Labor OSHA 1910.213 Regulations . 18 . REMOVEcut - offpiecesanddebrisfromthetable 34 . SAVE THESE iNSTRUCTiONS . Refer to them beforestartingthesaw . Thevibrationofthesaw frequently and use them to instruct other users . maycausethemto moveintothesawbladeandbe thrownout . Aftercuttingt , urnthesawoff . When thebladehascometoa completestop , unplugthe Information regarding the safe and proper operation of sawandremovealldebris . this tool is available from the following sources : 19 . NEVERSTARTthesawwiththeworkpieceagainst Power Tool Institute theblade . 1300 Summer Avenue Cleveland , OH 44115 - 2851 20 . NEVERperform " free - hando " perations . Useeither thefenceor mitergaugeto positionandguidethe www . powertoolinstitute . org workpieceH . oldtheworkpiecefirmlyagainstthe mitergaugeorfence . National Safety Council 1121 Spring Lake Drive 21 . USEa pushstick ( s ) for rippinga narrowworkpiece . Itasca , IL 60143 - 3201 22 . AVOID AWKWARD OPERATIONS AND HAND American National Standards Institute POSITIONS where a sudden slip could cause a 25 West 43rd Street hand to move into the blade . 4th floor New York , NY 10036 23 . KEEP arms , hands and fingers away from the blade . www . ansi . org 24 . NEVER have any part of your body in line with the path of the saw blade . ANSi 01.1 Safety Requirements for Woodworking Machines , and the U . S . Department of Labor regulations 25 . NEVER reach around or over the blade . www . osha . gov 26 . NEVER attempt to free a stalled blade without first turning the machine " OFF " and unplugging it from the power source .
Page: 9

AVAILABLE ACCESSORIES Sears may recommend other accessories not listed in this manual . Visit your Sears Hardware Department or see the Sears Power and Hand Tool Catalog for the following acces - See your nearest Sears Hardware Department or Sears sories . Power and Hand Tool Catalog for other accessories . ITEM STOCK NUMBER Do not use any accessory unless you have completely * Auxiliary Fence , Rip fence 29878 read the Owner's Manual for that accessory . * Miter Gauge Extension & Stop 29879 * Stock Clamp , Miter Gauge 29880 * Dust Chute with Dust Port 22102 * Micro - Adjustment Assembly 29881 Use only accessories recommended for this table saw . * Table Insert - Standard 29882 Using other accessories may cause serious injury and * Table Insert - Dado 29885 cause damage to the table saw . * Table Insert - Molding Cutterhead 29887 * Saw Blade - Leitz ; 10 - in . x 40 tooth 29888 variable pitch blade * Fence Guide System 32371 CONSTRUCTING A FEATHERBOARD Fig . 2A 24 " ' 5 " _ 1 Figure 2A illustrates dimensions for making a typical Fig . 2B featherboard . The material , which the featherboard is constructed of , should be straight piece of wood that is free of knots and cracks . Featherboards are used to keep the work in contact with the fence and table and help prevent kickbacks . Clamp the featherboard to the fence and table so that the leading edge of the feather - board will support the workpiece until the cut is com - pleted . Use featherboards for all non - through cutting opera - tions where the guard and splitter assembly must be removed . Always replace the guard and splitter assembly when the non - through cutting operations are finished . See figure 2B .
Page: 10

CONSTRUCTING A PUSHSTICK When ripping work less than 4 inches wide , a pushstick should be used to complete the feed and could easily be made from scrap material by following the pattern shown in figure 2C . Fig . 2C The Pushstick should be made of 3 / 4 or 1 / 2 inch wood or a thickness less than the width of the workpiece to be cut . Figure 2C should be copied and scaled so the grids are 1 / 2 inch square . This copy can be used to make your pushstick . 10
Page: 11

UNPACKING AND CHECKING CONTENTS Fig . 3 - 1 The table saw is a heavy machine , two people are required to unpack and lift the table saw . This table saw w [ [ [ require some amount of assembly . This table saw and fence is shipped in one carton . This carton also contains a box of saw parts . 1 . Remove parts from all of the cartons and lay them on a clean work surface . 2 . Two or more people are required to lift the table saw off of the shipping pallet . 3 . Remove any protective materials and coatings from all of the parts and the table saw . The protective coatings can be removed by spraying WD - 40 on them and wiping it off with a soft cloth . This may need redone several times before all of the protec - tive coatings are removed completely . CAUTION : DO NOT use acetone , gasoline or lacquer thin - ner to remove any protective coatings on your table saw . 12 4 . After cleaning , apply a good quality paste wax to any unpainted surfaces . Make sure to buff out the wax before assembly . 5 . Compare the items to figures below ; verify that all items are accounted for before discarding the ship - ping box . If there are any missing parts , call Customer Helpline 1 - 800 - 897 - 7709 . The right extension wing must be completely assem - bled and motor cover closed and fastened before table saw is to be connected to the power source . If any parts are missing , do not attempt to plug in the power cord and turn " ON " the table saw . The table saw can only be turned " ON " after all the parts have been obtained and installed correctly . 10 TABLE SAW \ \ 1 . Table saw assembly \ \ \ 2 . Extension wing , stamped steel ( 2 ) \ \ \ \ 3 . Handwheel ( 2 ) \ \ \ 4 . Handwheel lock knob ( 2 ) \ \ \ \ 5 . Splitter mounting rod \ 6 . Splitter bracket assembly 7 . Wrench hook 8 . Fence hook ( 2 ) 9 . Poly - V belt 10 . Blade guard and splitter assembly / 11 . Leg assembly ( 2 ) 7 \ 12 . Tie bar ( 2 ) 5 13 . Switch 14 . Saw blade ( not shown ) 11
Page: 12

Fig . 3 = 2 20 21 22 23 24 28 FENCE 25 . Fence rear rail connector 20 . Rip fence assembly 26 . Front rail end cap , right 21 . Fence front rail , right 22 . Fence front rail , left 27 . Front rail end cap , left 28 . Fence front rail alignment bar ( 2 ) 23 . Fence rear rail , right 24 . Fence rear rail , left Fig . 3 = 3 4O MITER GAUGE 40 . Miter gauge 12
Page: 13

Hardwarepacksarenotidentifiedorlabeled . Seehardwarediagramto helpinfindingthecorrectpart . Seefigure3 - 4 . Fig . 3 = 4 © @ El HEX HEAD SCREW _ Sx | . a5 x a5ete _ HEX NUT _ 8xl.a5 @ @ 8 HEX HEAD SCREW MSxl . a5 × 30rtt , , HEX NUT 5116 " - 18 @ ® u EARRIA6E HEAD SCREW 5 / | 6 - | 8 X 5 / 8 " SOuARE HEAD SCREW _ BxL25 X 35 _ @ I ® @ FLAT WASHER _ 8 HEX SOCKET HEAD CAP SCREW MBx | . 25 x 25 _ ® © © l HEX SOCKET HEAD CAP SCREW NSx | , 25 x 35 _ e _ FLAIr WASHER 5 / | 6 " HEX HEAD SCREW M6 x 12Be _ LOCK WASHER N8 ROUND HEAD SELF - TAP SCREW _ F4 x B _ ROUND HEAD SELF - TAP SCREW _ × | 6 _ e _ LOCK WASHER 9 / | 6 " Hardware Pack for Cabinet Legs ( # 0R92020 ) Hardware Pack for Extension Wings ( # 0R92013 ) includes : includes : Flat Washer M8 ( 8 ) Flat Washer M8 ( 16 ) Flat Washer 5 / 16 " ( 8 ) Lock Washer M8 ( 8 ) Hex Head Screw M8xl . 25 x 30mm ( 8 ) Lock Washer M8 ( 8 ) Lock Washer 5 / 16 " ( 8 ) Hex Head Screw M8x1 . 25 x 25mm ( 8 ) Hardware Pack for Rear Rail ( # 0R92016 ) includes : Carriage Head Screw 5 / 16 - 18 x 5 / 8 " ( 8 ) Flat Washer M8 ( 8 ) Hex Nut M8 ( 8 ) Hex Nut 5 / 16 " ( 8 ) Lock Washer ( 6 ) Button Head Cap Screw M8x1 . 25 x 25mm ( 4 ) Hardware for ON / OFF Switch : Button Head Cap Screw M8x1 . 25 x 35mm ( 2 ) ( Hardware finish is Black Oxide ) Hex Nut M8 ( 2 ) Hex Head Screw M6 x 12mm ( 2 ) Hardware Pack for Front Rail ( # 0R92017 ) Square Nut M6 ( 2 ) includes : Miscellaneous Hardware : Flat Washer M8 ( 4 ) Lock Washer M8 ( 4 ) Sheet Metal Screw M4 x 8mm ( 6 ) Sheet Metal Screw M4 x 16mm ( 4 ) Square Head Screw M8x1 . 25 x 35mm ( 4 ) Hex Nut M8 ( 4 ) 13
Page: 14

2 4 5 6 7 8 10 11 12 23 13 15 22 16 17 18 21 20 19 9 . Rear rail 18 . Cabinet leg 1 . Splitter assembly 19 . Rubber foot 2 . Blade guard 10 . lO - in , stamped steel wing 11 . Front rail with scale 20 . Fence hook 3 . Anti - kickback fingers 4 . Blade 21 . On / Off switch 12 . Rip fence lock handle 13 . Motor cover 22 . Bevel handwheel 5 . Align - a - cut insert 6 . Rear fence hold down 14 . Bevel scale 23 . Bevel handwheel lock knob 7 . Table surface 15 . Blade height handwheel 24 . Miter gauge 16 . Handwheel lock knob 8 . Rip fence 25 . Miter gauge groove 17 . 3 / 4 Cabinet 14
Page: 15

TOOLS REQUIRED 2 . Attach leg assemblies ( A ) to the front ( B ) and rear ( C ) of the table saw cabinet by placing ( D ) eight The following tools are needed for assembly and align - M8 x 25mm hex head screws and eight M8 flat ment . Note : Two blade wrenches and five hex wrenches washers down through the mounting holes in the are provided with your table saw . The remaining tools leg assembly and cabinet ( E ) . Place an M8 flat are typical shop tools and are not included with your washer , M8 lock washer and M8 hex nut onto each table saw . of the eight screws attaching leg assembly to cabi - net . Do not completely tighten hardware at this 18mm wrench 8mm wrench time . See figure 4 - 1 . 13mm wrench 3 / 16 - in . hex wrench 3 . Attach two tie bars ( F ) inside and between front and 10mm wrench # 2 Phillips screwdriver rear legs already attached to the cabinet with ( G ) eight 5 / 16 - 18 x 5 / 8 " carriage head screws , 5 / 16 " flat washers , 5 / 16 " lock washers and 5 / 16 - 18 hex nuts and securely tighten all hardware . See figure 4 - 1 . • The table saw is a heavy machine ; two people are required for certain assembly operations . POLY = V BELT ASSEMBLY • DO NOT assemble the table saw until you are sure the tool is unplugged . MAKE CERTAIN the table saw is disconnected from • DO NOT assemble the table saw until you are sure the power switch is in the " OFF " position . the power source . • For your own safety , DO NOT connect the machine to Figure 5 = 1 the power source until the machine is completely assembled and you read and understand the entire Owner's Manual . / A CABINET LEG ASSEMBLY MAKE CERTAIN the table saw is disconnected from the power source . 1 . Turn the table saw upside down onto its cast iron table . CAUTION : The table saw is heavy ; two peo - ple are required for this operation . Be sure to lay cardboard on the floor to protect the table surface . Figure 44 o " ll 1 . Make sure all packaging material has been removed from inside the cabinet . 2 . Open the motor cover and place the motor Poly - V belt ( A ) over the blade pulley ( B ) . See figure 5 - 1 . 3 . Carefully lift the motor ( C ) and place the belt under C the motor pulley ( not shown ) . Make sure all the v - F notches in the belt are mated with the v - notches of the blade and motor pulley . See figure 5 - 1 . 4 . Carefully let the motor down and close motor cover . 15
Page: 16

EXTENSION WiNG ASSEMBLY HANDWHEEL ASSEMBLY MAKE CERTAIN the table saw is disconnected from MAKE CERTAIN the table saw is disconnected from the power source . the power source . Figure 7 = 1 The right extension wing must be completely assem - bled and motor cover closed and fastened before table saw is to be connected to the power source . C Figure 64 A o _ B 1 , Place one of the handwheels ( A ) onto the bevel shaft ( B ) located on the side of the cabinet . Align CAUTION : The extension wings are heavy ; two the groove ( C ) in the back of the handwheel with people are required to assemble both extension the pin ( D ) . See figure 7 - 1 . wings to the table saw . 2 , Assemble one of the extension wings ( A ) to the left side of the table saw . Align the four holes ( B ) in the extension wing with the four holes in the left side of Figure 7 = 2 the saw table . Use four M8 x 30mm hex head screws , M8 lock washers and M8 flat washers . Do not completely tighten hardware at this time . See figure 6 - 1 . Figure 6 = 2 2 , Thread the locking knob ( E ) onto the threaded end of the shaft ( F ) . See figure 7 - 2 . 3 , Repeat the steps above to assemble the remaining handwheel and locking knob onto the blade raise / 3 . Lay a straight edge ( C ) across the saw table ( D ) lower shaft located on the front of the cabinet . and extension wing ( E ) . Make sure that the front face of the extension wing ( F ) is flat to the front face of the saw table ( G ) . Adjust the extension wing so that its top surface is exactly flat to the saw table and securely tighten hardware . See figure 6 - 2 . 4 . Repeat steps 2 and 3 above to assemble the other extension wing to the right side of the table saw . 16
Page: 17

WRENCH AND FENCE HOOK ASSEMBLY Figure 9 = 2 MAKE CERTAIN the table saw is disconnected from the power source . Figure 84 3 . Place the splitter bracket assembly ( C ) onto the mounting splitter rod . See figure 9 - 2 and 9 - 3 . A i Figure 9 = 3 1 . Assemble both of the fence hooks ( A ) to the left H side of the cabinet ( B ) using four M4 x 8mm sheet metal screws , not shown . See figure 8 - 1 . 2 . Assemble the wrench hook ( C ) above the fence hooks using two M4 x 8mm sheet metal screws , not shown . See figure 8 - 1 . BLADE GUARD AND SPLITTER ASSEMBLY G MAKE CERTAIN the table saw is disconnected from the power source . E 1 . Loosen table insert retainer bolt and remove table insert . 4 , Place the front attachment point ( D ) of the blade Figure 94 guard and splitter assembly ( H ) down into the tool - less front attachment point ( E ) and the rear attach - ment slot ( F ) onto the threads of the splitter bracket knob ( G ) ; securely tighten splitter bracket knob . B Note : The splitter bracket assembly will need to be positioned to fit the blade guard and splitter assem - bly on the mounting splitter rod . See figure 9 - 3 . 5 , Remove the hex nut ( K ) and outer flange ( J ) from the blade arbor ( I ) . Note : The arbor has a right hand thread ; to loosen the hex nut , turn it counterclock - 2 . Place the threaded end of the mounting splitter rod wise . See figure 9 - 4 . ( A ) through the hole ( B ) in the rear of the cabinet . Place a M12 hex nut ( not shown ) onto the threaded end of the mounting splitter rod inside of the cabi - net and tighten securely . See figure 9 - 1 and 9 - 2 . Note : Place an 18mm wrench on 12mm hex nut and a 13mm wrench on flats of the splitter rod and tighten . 17
Page: 18

Figure 9 = 4 Figure 9 = 6 Z M u \ \ \ \ K 8 . Lay a straight edge ( R ) against the left side of the saw blade ( S ) . Align the splitter ( T ) so that it is in a straight line with the blade and tighten the one hex 6 . Place 10 " saw blade ( Z ) onto blade arbor ( I ) ; make socket head screw ( U ) on top of the splitter bracket sure the teeth of the blade are pointing down in the assembly . See figure 9 - 6 . front of the table saw . Place the outer flange ( J ) and hex nut ( K ) onto the blade arbor and snug hex 9 . Replace table insert and tighten table insert retain - nut by hand . Place the open - end blade wrench ( L ) ing bolt removed in step 1 . on the flats of the inner blade flange ( not shown ) and the box - end blade wrench ( M ) onto the hex nut 10 . If there is any problem with the front splitter attach - and securely tighten . Note : The blade arbor has a ment bracket being out - of - square to the saw table right hand thread ; to tighten the hex nut turn it or blade alignment , see " AMGNING SPLITTER clockwise . See figure 9 - 4 . BRACKET " in the Operations and Adjustments section of this manual . Figure 9 = 5 RiP FENCE ASSEMBLY O MAKE CERTAIN the table saw is disconnected from Q the power source . \ \ Figure 10 = 1 \ \ \ C \ C A \ \ \ " D \ 7 . Place a square ( N ) onto the saw table and against the splitter assembly ( 0 ) behind the kickback fingers ( P ) . Make adjustments to the splitter bracket assembly ( Q ) so that the splitter is square E to the saw table . Once square , tighten the two hex A socket head screws on the bottom of the splitter B bracket assembly . See figure 9 - 5 . 18
Page: 19

Alignment bars ( B ) have set screws ( A ) already 1 . Figure 10 = 3 installed . Make sure set screws are flush with face of alignment bar . See figure 10 - 1 . H 2 . Place both fence front rails ( C ) on the saw table upside down . Make certain that the right fence rail is on the right - hand side and the left front rail is on the left - hand side . Check that both scales on the front rails have the 1 - inch marking closest to each other . See figure 10 - 1 . 3 . Insert both alignment bars halfway into the back ( D ) and bottom ( E ) square nut grooves in the right front rail and slightly snug set screws to hold alignment bar into the front rail . See figure 10 - 1 . 4 . Slide the left front rail onto alignment bars and against other half of front rail . Make sure both sec - tions of the front rails are flat and straight to each other . Slightly snug set screws in both alignment bars . Recheck that the front rail is flat and straight , then securely tighten all set screws . Figure 10 = 2 F / 0 7 . Raise saw blade ( H ) and place a straight edge ( I ) against right side of saw blade extending out over front of saw table . Align the edge of the right front rail ( J ) with right side of saw blade using the straight edge . See figure 10 - 3 . G Figure 10 = 4 G 5 . Slide the heads of four M8 x 35mm square head screws ( F ) , two from each end of the front rail into the front rail . Note : The front rail is still positioned upside down on the saw table . Position the screws so that they will align with the two holes in the front of the saw table and one hole ( G ) in each extension wings . See figure 10 - 2 . 6 . Place front rail against front of saw table with the four screws going through the four holes in the saw table and extension wings . Place an one M8 flat washer , M8 lock washer and M8 hex nut onto each of the four screws on the back side of the saw table and extension wings . Do not completely tighten the four hex nuts at this point . 8 . Using a combination square ( K ) , make sure the front rail ( L ) is level across the saw table and exten - sion wings , and then securely tighten the four hex nuts . See figure 10 - 4 . 19
Page: 20

Figure 10 = 5 Figure 10 = 7 AB s M AC \ W V 9 , Assemble the left side rear rail ( M ) to the left rear side of the table saw ( N ) . Attach rear rail ( M ) to table ( N ) with two M8 x 25mm hex button head screws , M8 flat washers , and M8 Iockwashers ( O ) . 13 . Assemble the two cursors ( U ) to the rip fence Attach rear rail to extension wing with one M8 assembly ( V ) using four M5 x 16mm pan head x 35mm hex button head screw , M8 flat washer , screws and M5 lock washers ( W ) . See figure 10 - 7 . M8 Iockwasher , and M8 hex nut ( P ) . Make sure 14 . Lift up on the rip fence handle ( X ) and place the that the rear rail is below the bottom of the miter fence down onto the saw table with the fence body gauge slots ( R ) in the saw table . See figure 10 - 5 into front rail . With the rip fence lock handle up , and 10 - 6 . you can slide the fence back and forth across the saw table . Pushing the rip fence lock handle down , 10 . Slide rear rail connector ( S ) into the left rear rail this will lock the fence from moving . See figure 10 - 7 . already assembled . See figure 10 - 5 . 15 . Align left fence side ( AB ) at a distance from the right side ( AC ) of the right miter gauge groove and Figure 10 = 6 lock the fence . See figure 10 - 7 . 16 . Use a measuring tape to measure the distance T R from the saw blade right side to the left fence side . 17 . Assemble the cursor ( U ) to the right side of fence cross arm with two M5 x 16mm pan head screws and M5 Iockwashers ( W ) . Do not completely tighten screws . See figure 10 - 7 . 18 . Align cursor with the scale ( Z ) so that the thin black line ( Y ) is on the same number as the distance measured in step 16 . Tighten the cursor screws . 19 . Remove fence from table and reposition it on left side of saw blade . Align right fence side at a dis - tance from the left side of left miter gauge groove and lock the fence . 11 . Slide the right side rear rail ( T ) onto rear rail con - nector . Assemble the right rear rail with two M8 x 20 . Use a measuring tape to measure the distance 25mm hex button head screws to the saw table from the saw blade left side to the right fence side . and one M8 x 35mm hex button head screw , M8 21 . Assemble the second cursor to left side of fence flat washer , M8 lock washer and M8 hex nut to the cross arm with two M5 x 16mm pan head screws extension wing . See figure 10 - 6 . and M5 Iockwashers . Do not completely tighten screws . 12 . Using a combination square , make sure the rear rail 22 . is level to the saw table and extension wings and Align cursor with the scale so that the thin black line is on the same number as the distance measured in below the bottom of the miter gauge slots , then step 20 . Tighten the cursor screws . securely tighten all hardware . 20
Page: 21

3 . Slide the M6 square nuts and switch assembly ( E ) Figure 10 = 8 into the left end of the front rail ( F ) . See figure 11 - 1 . 4 . Position the switch assembly to desired location and tighten hardware . CAUTION : Keep switch out of saw blade path . Most common switch location is to the left side of the saw blade . AA Figure 11 = 2 23 . Note : The rip fence comes with a rear hold down ( AA ) built into the end of the fence , to keep the rear of the fence from lifting while using a feather board . Engage the rear hold down by simply flipping down on the hold - down arm so that it is under the rear rail , as shown . See figure 10 - 8 . 24 . Check and make sure the rip fence is square to the saw table and is parallel to the miter groove . If any 5 . Place the left front rail end cap ( A ) into the end adjustments are needed see " FENCE ADJUST - of the front rail ( B ) . Attach end cap to rail with MENTS " in the Operation and Adjustments section two M4 x 16mm sheet metal screws ( C ) . in this manual . See figure 11 - 2 . ON / OFF SWITCH AND 6 . Repeat step above to attach right side front rail END CAP ASSEMBLY end cap . CONNECTING SWITCH CORD MAKE CERTAIN the table saw is disconnected from TO MOTOR CORD the power source . Figure 11 = 1 MAKE CERTAIN the table saw is disconnected from the power source . C Figure 12 = 1 A E J 1 . Place two M6 x 12mm hex head screws ( A ) up through the two holes ( B ) in the switch support ( C ) . See figure 11 - 1 . 1 . Place the switch cord ( A ) through hole ( B ) in front 2 . Thread two M6 square nuts ( D ) onto M6 x 12mm hex of cabinet . See figure 12 - 1 . head screws about three turns . See figure 11 - 1 . 21
Page: 22

2 . Open motor cover , plug switch cord ( C ) into motor BOLTING TABLE SAW TO THE FLOOR cord ( D ) . See figure 12 - 2 . MAKE CERTAIN the table saw is disconnected from Fig . 12 - 2 the power source . If you wish , the table saw can be permanently mounted to the floor . To attach to the floor , see instructions below . Fig . 12A - 1 B 3 . Pull slack in switch cord into the cabinet . 4 . Make a loop ( E ) from the slack of the switch cord and place it behind cord retaining bar ( F ) . See figure 12 - 2 . B A 1 . Remove the four rubber footpads ( A ) from the table saw legs ( B ) . See Figure 12A - 1 . 2 . Position the table saw where you want it perma - nently mounted . 3 . Mark the floor through the holes in the bottom of legs . 4 . Move the table saw out of the way and drill pilot holes at the four locations marked . 5 . Attach the table saw to the floor using appropriate hardware ( not included ) . 22
Page: 23

CAUTION 2 . To turn the table saw on , press the green " ON " button ( A ) in one - half inch . Note : There is a safety • A separate electrical circuit should be used for your feature on the switch to insure that the switch must table saw . The table saw comes pre - wired for 120 - volt use . The circuit should not be less than # 14 AWG wire be completely pressed before the saw will START . See figure 13 - 1 . and should be protected with a 15 - amp time lag fuse . • Have a qualified electrician repair or replace damaged 3 . To turn the table saw off , press the large red " OFF " or worn cord immediately . paddle ( B ) or lift the paddle and press directly on the red " OFF " button . See figure 13 - 1 . • Before connecting the motor to the power line , make certain the switch is in the " OFF " position and be sure that the electric current is of the same characteristics LOCKING ON / OFF SWITCH as the motor nameplate . All line connections should make good contact . 1 . When the table saw is not in use , the " ON " button should be locked so that it cannot be started . • Running on low voltage or long extension cords will damage the motor . 2 . Using the padlock included with your table saw , lift the red " OFF23 " paddle and place the padlock through the holes ( C ) in the side of the " ON " button and then lock the padlock . Make sure keys have been removed from padlock and placed where no children can get them . See figure 13 - 1 . • DO NOT expose the table saw to rain or operate the in damp locations . 3 . To use the table saw , unlock and remove the pad - lock from the " ON " button . • MAKE SURE all parts have been assembled correct - ly and are in working order . • KEEP table surface clear of tools and debris before THERMAL = OVERLOAD PROTECTION starting table saw . • Turn the power switch " OFF " and unplug the power STARTING AND STOPPING THE SAW cord from its power source prior to doing or perform - ing any maintenance . Figure 13 = 1 • Make certain that the OFF button has been depressed before pushing the thermal overload reset button . C The motor supplied with your table saw has a resettable thermal - overload relay ( D ) , see figure 13 - 1 . If the motor shuts off during an operation ( cutting a workpiece too fast or using a dull blade , using the saw beyond its capacity , or low voltage ) press the OFF button and let A the motor cool three to five minutes . Push the reset thermal - overload button on the side of the ON / OFF switch assembly . Make certain that the saw blade and work area has been cleared of debris before restarting saw . The motor can now be turned on again . 1 . The ON / OFF switch is located under the front rail on the table saw . 23
Page: 24

RAiSiNG AND LOWERING THE BLADE ADJUSTING BLADE BEVEL POSITIVE STOPS Figure 14 = 1 Figure 15 = 1 The blade height adjustment handwheel and handwheel lock knob are located on the front of the cabinet above the blade bevel scale . To raise the saw blade , loosen the handwheel lock knob ( A ) ( counter - clockwise ) and turn the handwheel ( B ) clockwise . When the saw blade 1 . To adjust blade 90 - degree blade bevel positive is at its desired height , tighten the handwheel lock knob stop , raise the saw blade ( A ) to its highest position . ( clockwise ) until it is securely tightened . See figure 14 - 1 . See figure 15 - 1 . 2 . Using a combination square ( B ) check that the To lower the saw blade , loosen the handwheel lock knob blade is 90 - degrees to the saw table ( zero degrees ( counter - clockwise ) and turn the handwheel counter - on bevel scale ) . See figure 15 - 1 . clockwise . When the saw blade is at its desired height , tighten the handwheel lock knob ( clockwise ) until it is 3 . If the blade will not tilt to 90 - degree , turn ( counter - securely tightened . clockwise ) the set screw ( C ) in the left hand side of the saw table until the blade can be positioned to 90 - degrees . Tighten bevel handwheel lock knob , located on the left side of the cabinet . This will keep TILTING THE BLADE the blade from further tilting and check that the set The blade bevel handwheel and handwheel lock knob screw is contacting positive stop . See figure 15 - 1 . is located on the left side of the cabinet . To increase 4 . If the blade has been tilted to 90 - degrees , tighten the saw blade - bevel , loosen the handwheel lock knob bevel handwheel lock knob , located on the left side ( A ) ( counter - clockwise ) and turn the handwheel ( B ) of the cabinet . This will keep the blade from further clockwise . When the saw blade is at its desired tilting . Turn the set screw clockwise until it comes degree , tighten the handwheel lock knob ( clockwise ) in contact with the positive stop . until it is securely tightened . See figure 14 - 1 Figure 15 = 2 To return the saw blade bevel to zero degrees , loosen the handwheel lock knob ( counter - clockwise ) and turn the handwheel counter - clockwise . When the saw blade is back to zero degrees it will come into contact with the adjustable positive stop which will cause the blade to stop . Tighten the handwheel lock knob ( clockwise ) until it is securely tightened . To tilt the blade bevel to 45 - degrees , loosen the hand - wheel lock knob ( counter - clockwise ) and turn the hand - wheel clockwise . When the saw blade is at 45 - degrees it will come into contact with the adjustable positive stop which will cause the blade to stop , tighten the hand - wheel lock knob ( clockwise ) until it is securely tightened . 24
Page: 25

BLADE HEEL ALIGNMENT 5 . Toadjustblade45 - degreebladebevelpositiveon . stop , raisethesawbladeto itshighestpositi CHECKING BLADE ALIGNMENT 6 . Usinga combinatiosnquare ( D ) checkthatthe bladeis 45 - degreetso thesawtable ( 45 - degrees Blade heel is the misalignment of the blade to the miter onbevelscale ) . Seefigure15 - 2 . slots . This means when the blade is not parallel to the 7 . Ifthebladewillnottiltto 45 - degreestu , rn ( counter - miter slots it is heeling . The blade is set parallel at the clockwiset ) hesetscrew ( E ) intherighthandside factory and should not need any adjustments . You can ofthesawtableuntilthebladecanbepositionedto check this by using a dial indicator ( not included ) or a 45 - degreesT . ightenbevelhandwheelol ckknob , combination square ( not included ) . It is recommended locatedontheleftsideofthecabinetT . hiswillkeep to check the alignment before initial operation as thebladefromfurthertiltingandcheckthattheset follows : screwiscontactingpositivestop . Seefigure15 - 2 . 8 . Ifthebladehasbeentiltedto45 - degreesti , ghtenide bevelhandwheelol ckknob , locatedonthelefts MAKE CERTAIN the table saw is disconnected from ofthecabinet . Thiswillkeepthebladefromfurther the power source . tilting . Turnthesetscrewclockwiseuntilit comes incontacwt iththepositivestop . Fig . 16A - 1 BEVEL ARROW ADJUSTMENT 1 . Make certain that the blade is at 90 - degrees to the table surface with a combination square . See figure 16 - 1 . Figure 16 = 1 / A 1 , Raise the saw blade to its highest point . 2 . Place a combination square ( A ) on the saw table with one edge ( B ) of the square against the left 2 . Check that the bevel arrow ( A ) is pointing to the miter slot ( C ) . See Figure 16A - 1 . zero degree mark on the bevel scale ( B ) located on the front of the cabinet . See figure 16 - 1 . 3 , Adjust the square so the rule ( D ) just touches the saw blade about 1 inch in from the outer diameter . 3 . To adjust arrow , loosen the Philips head screw ( C ) Make sure the rule is not touching any of the car - and reposition the bevel arrow and tighten screw . bide tips of the saw blade . See figure 16 - 1 . 4 , Lock the rule in this position . 5 . This dimension should be around 5 - 1 / 2 inch , plus or minus 3 / 32 of an inch . 25
Page: 26

Fig . 16A - 2 Fig . 16B = 1 \ A A 6 , Rotate the saw blade back so that you take the measurement from the same spot on the saw 1 , To align the blade parallel to the miter slot , first blade . See Figure 16A - 2 . loosen two hex head screws ( A ) under the left side of the table saw . This is the same side as the bevel 7 , Take a reading at the rear of the blade ( E ) with the handwheel ( B ) . See figure 16B - 1 . combination square . If there is a difference of more than four pieces of standard printer paper between Fig . 16B = 2 the rule and the blade then adjustment will have to be made . C 8 , If an adjustment is necessary see " ADJUSTING BLADE ALIGNMENT " . ADJUSTING BLADE ALIGNMENT Blade alignment is factory set and should not need adjustment . All saw blades have some runout . Therefore , readjusting the blade alignment should only be attempted if it becomes necessary ( see checking blade alignment ) . 2 , Open motor cover located on the right side of the table saw . Loosen two hex head screws ( C ) locat - MAKE CERTAIN the table saw is disconnected from ed directly above the opening . See Figure 16B - 2 . the power source . 3 , The saw table is now loose and can be reposi - tioned until the blade is parallel to the miter slot . Repeat steps in " CHECKING BLADE ALIGNMENT " . 4 , When blade is parallel to miter slot tighten all four hex head screws . 5 . Recheck blade alignment . 6 . Tilt the blade to 45 degrees , and rotate the saw blade by hand . Make sure the blade does not contact the table insert . 26
Page: 27

RiP FENCE OPERATIONS ADJUSTING FENCE SLIDE AND ADJUSTMENTS MAKE CERTAIN the table saw is disconnected from MAKE CERTAIN the table saw is disconnected from the power source . the power source . To make sure your fence slides smoothly there are The rip fence can be used on either side of the saw several items to check . blade . The most common location is on the right hand side . This fence is a front locking fence , meaning it Fig . 17 = 2 only clamps on the front rail . The fence slides across the front and rear rails . B A Figure 17 = 1 B c G D F B A H 1 , Make sure that the nylon set screws ( A ) and nylon glide pads ( B ) are in place and are not damaged , gouged or have sharp edges . See figure 17 - 2 . Note : Some models do not have the Micro - H Adjustment Assembly as shown in figure 17 - 2 . Fig . 17 = 3 To move the rip fence , lift up on the fence handle ( A ) and slide the fence back and forth across the saw table . Note : The fence handle is spring loaded and will stay in the up position until press down on . See figure17 - 1 . D 2 , To lock the fence from sliding side to side , push down on the fence handle . C 2 . Make sure that both the front and rear rails ( C ) are parallel to the saw table ( D ) . Use a combination square ( E ) to check parallel . See figure 17 - 3 . 27
Page: 28

Fig . 17 = 4 Fig . 17 = 6 G F Clean and wax \ MAKE CERTAIN you read and follow all directions and warnings on the cleaner . 4 . Clean the front and rear rail with rubbing alcohol or automotive brake cleaner . Make sure not to get 3 . Make sure there is a consistent gap between the cleaner on any painted surfaces . After cleaning , bottom of the fence ( F ) and the saw table ( G ) . wax the entire front and rear rail . For models that This gap should be same as the thickness of a have the Micro - Adjustment assembly , do not wax dime , around 0.050 " . To adjust the gap at the front the area of the front rail where the rubber wheel of the fence turn nylon set screws ( H ) evenly . from the micro - adjust contacts . See figure 17 - 4 . To adjust the gap at the rear of the fence , loosen two ADJUSTING RIP SCALE screws ( I ) . The screws are located inside of the fence 1 . To adjust the right scale , align left fence side ( B ) at end cap ( J ) . The fence hold down ( K ) will have to be a distance from the right side ( C ) of the right miter rotated down to access the two screws . Reposition the gauge groove and lock the fence . See figure 17 - 1 . fence end cap to set the gap and tighten the two screws . See figure 17 - 5 . 2 . Use a measuring tape to measure the distance from the saw blade right side to the left fence side . Fig . 17 = 5 3 . Loosen two screws attaching the cursor ( E ) to the right side of fence cross arm . See figure 17 - 1 . 4 . Align cursor with the scale ( F ) so that the thin black line ( D ) is on the same number as the distance measured in step 4 . Tighten the cursor screws . 5 . To adjust the left scale , remove fence from table and reposition it on left side of saw blade . Align right fence side at a distance from the left side of left miter gauge groove and lock the fence . 6 . Use a measuring tape to measure the distance from the saw blade left side to the right fence side . 7 . Loosen two screws attaching the cursor to the left side of fence cross arm . 8 . Align cursor with the scale so that the thin black line is on the same number as the distance measured in step 6 . Tighten the cursor screws . K 28
Page: 29

Figure 17 = 7 K Theripfencemustbeproperlyalignedto themiter gaugegrooveinordertoprevent " kickbackw " hen ripping . ADJUSTING RiP FENCE PARALLEL : 1 . To adjust the rip fence parallel to the miter gauge groove , position the rip fence ( B ) along the right side ( C ) of the right hand miter gauge groove and lock the fence . The rip fence should be parallel to the miter gauge groove . If an adjustment is neces - sary , proceed to the next step . See figure 17 - 1 . 2 . Lift the fence handle and slightly loosen hex head screw ( G ) . Lightly tap on the rear of the fence until the rip fence is parallel to the miter gauge groove . Lock the fence and retighten hex head screws . REAR HOLD DOWN : Unlock the fence and move it side to side . Lock and recheck it for parallel . See figure17 - 1 . To minimize the amount the rear of the fence ( K ) comes off the saw table , simply flip down the rear hold down ADJUSTING RiP FENCE SQUARE : ( L ) so that it is under the rear rail . This limits the amount that the rear of the fence will lift . To adjust the rip fence square to the table surface , lock the fence in place and place a square on the TABLE INSERT ADJUSTMENT saw table and against the side of the rip fence . If the rip fence is out - of - square , proceed to the next step . MAKE CERTAIN the table saw is disconnected from 2 . Unlock the rip fence handle and adjust one or both the power source . set screws ( H ) to make the rip fence square to the saw table . Lock the rip fence handle and recheck . Figure 18 = 1 CAUTION : Keep about lmm gap between saw table and bottom of fence . Ten sheets of printer paper are about lmm . See figure 17 - 1 . C ADJUSTING CLAMPING PRESSURE : After the rip fence is parallel to the miter gauge groove , check to see if there is adequate clamping force to hold the rip fence in place . If you can lift the rip fence up off the front rail while it is locked , it needs adjusted . 2 , To adjust the clamping pressure of the rip fence , slightly loosen two hex socket head screws under - neath fence body d ) . To increase clamping pres - sure turn set screw ( J ) clockwise ; to decrease 1 , The table insert ( A ) must always be level with the clamping pressure turn set screw counter - clockwise saw table ( B ) . To adjust the table insert , loosen and tighten both hex socket head screw . Note : and remove table insert retaining bolt ( C ) . See fig - ure 18 - 1 . Only make small adjustments to set screw ( J ) and recheck . See figure 17 - 1 . 2 , Place a straight edge across the front and rear of the table insert . Check that the insert is perfectly level with the saw table . 3 . To level the table insert , turn the one or more adjusting set screws ( D ) as needed and recheck . See figure 18 - 1 . 4 . Once the insert is level , secure the insert with the retaining bolt removed in step 1 . 5 . The table insert is equipped with a finger hole ( E ) for easy removal . See figure 18 - 1 . 29
Page: 30

CHANGING MOTOR VOLTAGE CHANGING THE SAW BLADE • MAKE CERTAIN the table saw is disconnected from • Turn the power switch " OFF " and unplug the power the power source . cord from its power source . • Have a certified electrician make all electrical connec - • USE ONLY lO - in , diameter blades with 5 / 8 - in . arbor tions . All local and state codes must be maintained . holes , rated at or higher than 3800 R . P . M . The motor supplied with the table saw is a dual voltage 120 / 240 - volt , single phase motor . The motor is wired Figure 20 = 1 from the factory for 120 - volt operation . To change to 240 - volt operation for your table saw , proceed with the following instructions . It is also necessary to replace the 120 volt plug , supplied with the table saw , with a UL / CSA Listed plug ( not included ) suitable for 240 volts and the rated current of the motor . The table saw with a 240 volt plug should only be connected to an outlet having the same configuration as the plug . No adapter is available or should be used with the 240 volt plug . Figure 19 = 1 A C B 1 . Remove blade guard and splitter . 2 . Remove the table insert retaining bolt and remove the table insert . 3 . Unlock the raise / lower handwheel lock and raise saw blade to maximum height . 4 . Two wrenches are supplied with the table saw . Place one open - end wrench ( A ) on the flat of the saw arbor to keep it from turning . Place the closed - end wrench ( B ) on the arbor nut ( C ) . Turn the arbor nut wrench toward the front of saw to loosen it . Remove arbor nut , blade flange ( D ) and saw blade ( E ) . See figure 20 - 1 . 1 . Make sure switch is " OFF " and disconnect power 5 . Assemble the new saw blade , make certain the cord from power source . teeth point down at the front of the saw table and 2 . Open motor cover and verify on the motor tag ( A ) assemble the blade flange and arbor nut . Using that motor is dual voltage . See figure 19 - 1 . both blade wrenches as previously mentioned , tighten arbor nut in the opposite direction from 3 . If motor tag states that it is dual voltage remove junc - which it was loosened . tion box cover ( B ) on motor ( C ) . See figure 19 - 1 . 6 . Replace table insert and tighten the table insert 4 . Using wiring diagram on inside of junction box retaining bolt . cover , reconnect motor leads for 240 - volt operation . 5 . Replace junction box cover and close motor cover . 7 . Replace blade guard and splitter . 6 . Replace 120 volt plug with a UL / CSA Listed 240 volt plug rated for current of the motor . 7 . The ON / OFF switch is 4 - pole and does not need modified . 30
Page: 31

ALiGNiNG SPLITTER BRACKET Fig . 20A - 2 MAKE CERTAIN the table saw is disconnected from the power source . Fig . 20A = 1 A \ 2 , Place a straight edge ( C ) along the left side of blade ( D ) and adjust the front splitter bracket to align the splitter ( E ) with the blade . See figure 20A - 2 . 3 , Retighten the two hex socket head cap screws after the splitter has been aligned . 4 , If necessary , adjust the rear splitter bracket ( F ) make certain that entire splitter is in line with the B saw blade . See figure 20A - 2 . 5 , Recheck to make certain the splitter is still square To adjust front splitter bracket ( A ) , loosen the two to the saw table . If adjustments are necessary , see hex socket head cap screws ( B ) . See Fig 20A - 1 BLADE GUARD AND SPMTTER ASSEMBLY . 31
Page: 32

MITER GAUGE OPERATION 7 . Push in plunger and make adjustments to stop screw ( G ) so that it touches the plunger and tighten AND ADJUSTMENT lock nut . See figure 22 - 2 . 8 . Recheck the positive stop angel to the saw blade . insert the guide bar into the miter gauge groove MAKE CERTAIN the table saw is disconnected from and slide the miter gauge up to the saw blade . the power source . 9 . To check , place a square against the saw blade Figure 21 = 1 and miter gauge body . If any more adjustments are need repeat steps above . B _ 3o _ A 10 . To set both 45 - degree positive stops , repeat steps above . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ; - 12 - 221 22 3 CROSSCUTTING Crosscutting requires the use of the miter gauge ( A ) to position and guide the workpiece ( B ) . See figure 23 - 1 . C 1 . The miter gauge has adjustable positive stops at 0 - The use of non - Craftsman attachments and acces - degree and plus or minus 45 - degrees or it can be sories may result in risk of injury or damage to the manually set at any angle between plus or minus table saw . 60 - degrees . 2 . To rotate miter gauge body ( A ) , loosen knob ( B ) Figure 23 = 1 and pull out plunger ( C ) and rotate miter gauge body to desired angle and tighten knob . See figure D A 21 - 1 . 3 . To rotate to the next positive stop pull plunger out , rotate miter gauge body then push plunger back in and continue rotating miter gauge body until it stops against next positive stop . 4 . To adjust 0 - degree positive stops , loosen knob , pull out on plunger and turn miter gauge over . Figure 22 = 2 G D TO CROSSCUT : 1 . Place the workpiece against the miter gauge and advance both the miter gauge and workpiece toward the saw blade ( C ) . See figure 23 Note : The miter gauge may be used in either one of the miter gauge grooves . When bevel cutting ( blade tilted ) , use the right hand miter gauge groove so that the blade tilts away from the miter gauge and your hands . 2 . Start the cut slowly and hold the workpiece firmly against the miter gauge and the table . To avoid serious injury , NEVER hang onto or touch the 5 , Loosen the lock nut ( D ) 3 or 4 turns . See figure 22 - 2 . part of the workpiece that is going to be cut off ( D ) . 6 . Place a square against the guide bar ( E ) and front 3 . Continue cutting until the workpiece is cut in two . of the miter gauge body ( F ) . Square the miter gauge body to the guide bar and tighten knob . See 4 . Slide the miter gauge and workpiece back to the figure 22 - 2 . starting point . 32
Page: 33

CAUTION Note : Beforeslidingtheworkpieceback , givethework - piecea littlesidewaysshifttomoveit slightlyawayfrom When using the block as a cut - off gauge , it is very thesawblade . important that the rear end of the block be positioned so the workpiece is clear of the block before it enters the blade . See figure 23 - 3 . NEVERpickupanyshortcutoffscrappiecesfromthe tablewhilethesawis running . Wait until the saw blade has come to a complete stop . Never use the fence as a cut - off gauge when crosscutting . Figure 23 = 2 When cross - cutting a number of pieces to the same length , a block of wood can be clamped to the fence and used as a cut - off gauge as shown . It is important that this block of wood always be positioned in front of the saw blade as shown . Once the cut - off length is determined , secure the fence and use the miter gauge to feed the work into the blade . This block of wood allows the cut - off piece to move freely along the table surface without binding between the fence and the saw table , thereby lessening the possibility of kickback and injury to the operator . See figure 23 - 3 . Note : This block allows the cut - off scrap piece to move freely along the table surface without binding between the fence and the blade , thereby lessening the possibil - ity of kickback and injury to the operator . AUXILIARY FENCE 2 . Once the cut - off length is determined , lock the For added safety and convenience , the miter gauge can fence and slide the workpiece across the table be fitted with an auxiliary fence ( E ) if not already sup - surface until it contacts the block . Use the miter plied with one . If the auxiliary fence is not provided with gauge ( K ) to feed the workpiece into the blade . your saw , one can be purchased as an accessory or one can be made from a dimensional piece of hard - wood . This auxiliary fence can be fastened to the front of the miter gauge by using two screws ( not included ) To avoid kickback when using the block ( F ) as a cut - off through the slots ( not shown ) in the miter gauge body . gauge , it is very important that the rear end of the block See figure 23.2 . ( G ) be positioned so the workpiece ( H ) is clear of the block before it enters the blade ( I ) . Never use the fence Figure 23 = 3 ( J ) as a cut - off gauge when crosscutting . See figure 23 - 3 . F H K CUT - OFF GAUGE 1 . When cross - cutting a number of pieces to the same length , clamp a block ( F ) of wood to the fence ( J ) to use as a cut - off gauge . It is important that this block of wood always be positioned in front of the saw blade . See figure 23 - 3 . 33
Page: 34

CAUTION RIPPING When ripping a workpiece longer than three feet , it is recommended that the workpiece be supported at the rear of the table saw to keep it from falling . A roller o NEVER stand in the line of the saw blade path when stand can be purchased to support long workpieces to ripping . the rear of a table saw . • ALWAYS keep hands and fingers away from the saw CAUTION blade . If the workpiece is to be cut less than 4 - inches wide , a push stick ( E ) or guide should always be used to keep Figure 24 = 1 your hands away from the saw blade . See figure 24 - 2 . Figure 24 = 2 A C D Ripping is the operation of making a cut with the grain of the workpiece ; the rip fence ( A ) is used to position An accessory Craftsman Fence Guide can be purchased and guide the workpiece . Since the workpiece is to assist when making narrow cuts . See " ACCESSOR - pushed along the fence , it must have a straight edge IES AND ATTACHMENTS " section in this manual . and make solid contact with the saw table . The blade guard ( B ) and splitter assembly ( C ) must be used . The DADO BLADE SET splitter has anti - kickback fingers ( D ) to prevent the workpiece from kicking back , and the splitter assembly to prevent the wood kerf from closing and binding on the blade . See figure 24 - 1 . The blade guard and splitter assembly cannot be used when dadoing or molding and must be swung to the 1 . With the workpiece clear of the saw blade , start the rear of the saw . Blade guard must be reassembled motor . when finished dadoing or molding . 2 . Place the workpiece on the saw table with the straight edge against the fence . Figure 25 = 1 3 . Advance the workpiece slowly , holding it down and against the fence , then into the saw blade . Note : The workpiece can be fed through the saw blade with one or two hands depending on the size . 4 . Affter the workpiece is beyond the saw blade and anti - kickback fingers , you can remove your hand from the workpiece . When this is done , the work - piece will either stay on the table , tilt up slightly and be caught by the rear end of the guard , or slide off the table to the floor . Alternately , the feed can con - tinue to the end of the table , after which the work - piece is lifted and brought back along the outside edge of the fence . 5 . The cut - off part of the workpiece remains on the table and is not touched until the saw blade has come to a complete stop . A 34
Page: 35

Whenthedadobladeis 13 / 16 - incwhide , theoutside Dadoingiscuttinga non - ethrougchutthatproducesasets squarenotchintotheworkpieceM . ostdadoblad arborflange ( F ) cannotbeused . Onlythearbornut ( G ) ( notincludeda ) remadeupoftwooutsidedadoblades shouldbeused ; tightenthearbornutagainstthedado ( A ) andfourorfiveinsidechippers ( B ) . Shims ( E ) can bladebody . Donotlosetheoutsidearborflange , forit beplacedbetweenbladesandchipperstoslightlyvary willbeneededwhenreattachinagbladetothesawrt ( thewidthofa dado . Nomorethantwoshimsshouldbe arbor . Also , anaccessorydadobladetableinse H ) placedtogethebr etweenonesetof bladesorchippers . ( notincludedm ) ustbeusedinplaceofthestandard Shimscanbemadeof heavypaperb , rassormetal . tableinsert . Seefigure25 - 4 . Variouscombinationosfthedadobladesandchippers areusedto cutgroovesfrom1 / 8 " to 13 / 16 " forusein Figure 25 = 4 shelvingm , akingjoints , tenonsg , roovinge , tc . See figures25 - 1,25 - 2 , and25 - 3 . Figure 25 = 2 C H o ( NOT INCLUDED ) The blade guard and splitter assembly cannot be used when dadoing and must be swung to the rear of the saw . Dado blades and chippers have a set to their teeth . The teeth of the dado blades and chippers must be arranged so that the set of each tooth overlaps the next Figure 25 = 5 tooth . The set of the dado blade ( C ) and chipper ( D ) overlap as shown in Figure 26 - 3 . A shim ( E ) can be used as needed to control the exact width of a dado . \ \ See figures 25 - 2 and 25 - 3 . Figure 25 = 3 \ jD Figure 25 - 5 , shows a typical dado operation using the miter gauge . • Never use the dado head in a bevel position . • Always install blade guard and splitter assembly after dado operation is completed . 35
Page: 36

MOLDING HEAD CUTTER Figure 26 - 2 shows the molding cutterhead is assembled to the saw arbor as shown . Molding is cutting a shape on the edge or face of the workpiece . Cutting moldings with a molding cutterhead If the outside arbor flange ( D ) cannot be used with the ( not included ) on the circular saw is a fast , safe and molding cutterhead , tighten the arbor nut ( E ) against clean operation . The many different knife shapes avail - the cutterhead body . Do not lose the outside arbor able make it possible for the operator to produce almost flange , for it will be needed when reattaching a blade to any kind of molding , such as various styles of corner the saw arbor . Also , an accessory molding cutterhead moulds , picture frames , table edges , etc . table insert ( F ) ( not included ) must be used in place of the standard table insert . See figure 26 - 2 . Figure 26 = 1 Figure 26 = 3 G H C The molding head consists of a cutterhead ( A ) in which It is necessary when using the molding cutterhead to you can mount various shapes of steel knives ( B ) . add a wood facing ( G ) to the face of the rip fence ( H ) . Each of the three knives in a set is fitted into a groove The wood facing is attached to the fence with fasteners . in the cutterhead and securely clamped with a screw . A 3 / 4 - inch facing is suitable for most work although an The knife grooves ( C ) should be kept free of sawdust , occasional job may require 1 - inch facing . See figure which would prevent the cutter from seating properly . 26 - 3 . See figure 26 - 1 . Position the wood facing over the cutterhead with the cutterhead below the surface of the table . Turn the saw on and raise the cutterhead slowly . The cutterhead will • The blade guard and splitter assembly cannot be cut its own groove in the wood facing . used when dadoing or molding and must be swung to the rear of the saw . Blade guard must be reassem - bled when finished . • Never use molding cutterhead in a bevel position . Figure 26 = 2 • Never run the workpiece between the fence and the molding cutterhead as irregular shaped wood will cause kickback . CAUTION • When molding end grain , the miter gauge must be used . The feed should be slowed up at the end of the cut to prevent splintering In all cuts , pay attention to the grain , making the cuts in the same direction as the grain whenever possible . NOTINCLUDED 36
Page: 37

BACKLASH ADJUSTMENTS FOR mar or rust , so it is important to conduct routine mainte - nance to keep your table saw looking new . Cleaning BLADE RAISING / LOWERING AND and waxing the cast iron surfaces on a regular mainte - BLADE TILTING ASSEMBLIES nance schedule is recommended as follows : If any play is detected in the blade raising / lowering or To clean and maintain the unpainted cast iron surfaces : blade tilting assemblies , the following adjustments should be made . • Apply a heavy coat of WD - 40 onto the unpainted cast iron surface . Use a fine steel wool pad to buff the unpainted cast iron . Make sure to buff in a " front to rear " direction Turn the power switch " OFF " and unplug the power only . A side - to - side buffing motion will show in the cord from its power source when making adjustments . finely ground cast iron as a flaw , defect or scratches . NOTE : In the illustration below , the table saw has been • Reapply WD - 40 and buff the unpainted cast iron sur - faces until the stains or rust is removed . Make sure turned upside down and the blade removed for clarity . you use the same front - to - rear buffing direction to Figure 27 = 1 avoid scratching or marring the cast iron surface . • After all stains and / or rust have been removed , clean all eil and dirt from the table saw using a soft cloth or rag . Lastly , you need to apply a good automotive paste wax to all unpainted cast iron surfaces . This will help to protect the saw from rusting from further contact with moisture or oily hands . LUBRICATION The table saw has sealed lubricated bearings in the motor housing that do not require any additional lubrica - tion from the operator . A 1 , To adjust the blade raising / lowering assembly , CLEANING loosen lock - nut ( A ) and turn the eccentric sleeve With the table saw unplugged , blow off motor with low - ( B ) until all play is removed in the assembly , then pressure air to remove dust or dirt . Air pressure above tighten lock - nut . See figure 27 - 1 50 P . S . I . should not be used as high - pressured air may damage insulation . The operator should always 2 , To adjust the blade tilting assembly , loosen lock - nut wear eye protection when using compressed air . ( C ) and turn the eccentric ( D ) until all play is removed in the assembly , then tighten the lock - nut . Do not allow chips and dust to accumulate under table See figure 27 - 1 . saw . Keep area clean and in safe order . PROTECTING CAST IRON TABLE CAUTION : DO NOT USE FLAMMABLE MATERIALS FROM RUST to clean table saw . MAKE CERTAIN to turn the power " OFF " and unplug Only trained personnel should perform repairs to the the power cord from its power source . table saw . Contact your nearest Sears Service Center for authorized service . Unauthorized repairs or replace - The environment and frequency of human contact can ment with non - factory parts could cause serious injury have a very detrimental impact on unpainted cast iron to the operator and damage to the table saw . surfaces . Moisture , humidity and oils ( from human hands ! ) can cause the unpainted cast iron surfaces to 37
Page: 38

TOPREVENTINJURYTOYOURSELF or damage to the table saw , turn the power switch to the " OFF " position and unplug the power cord from the electrical receptacle before making any adjustments . PROBLEM LIKELY CAUSE ( S ) SOLUTION Motor does not 1 , 1 , Switch not pressed in far enough or switch Depress switch in 1 / 2 inch or make sure switch is in the start : in the " OFF " position . " ON " position . 2 . Defective switch . 2 . Have switch replaced . 3 . Defective capacitor . 3 . Have capacitor replaced . 4 . Low line voltage . 4 . Correct low line voltage condition . If saw is plugged into an extension cord , plug saw directly into wall outlet . 5 . Defective motor . 5 . Have motor replaced . NOTE : 3 and 4 must be done by a qualified service technician . 1 . Circuit overload . Motor stalls , 1 . Reduce circuit load ( turn off other appliances ) thermal - overload 2 . Low line voltage . 2 . Correct low line voltage condition . Check line voltage with a trips or circuit multi - meter . If saw is plugged into an extension cord , breakers open unplug saw from extension cord and plug saw directly to frequently : wall outlet . 3 . Motor overload . 3 . Reduce load on motor , slow down feed rate of workpiece being pushed into blade . 4 . Incorrect fuses on circuit breakers . 4 . Have correct fuses on circuit breakers installed by a quali - fied electrician . 5 . Short circuit in motor ; loose connections or 5 . Inspect terminals in motor for damaged insulation and worn insulation on lead wires . shorted wires and have them replaced . Check all power lead connections . Motor starts 1 . Low line voltage . 1 . Correct low line voltage condition . Check line voltage with a slowly or fails to multi - meter . If saw is plugged into an extension cord , come to full speed : unplug saw from extension cord and plug saw directly to wall outlet . 2 . Defective motor windings . 2 . Have motor replaced . 3 . Defective capacitor . 3 . Have capacitor replaced 1 . Restricted air circulation due to dust 1 . Clean dust and restore normal air circulation around motor . Motor running too hot : accumulation . 2 . Reduce load on motor . 2 . Motor overload . Handwheels are hard 1 . Handwheel Lock Knob has not been loosened . 1 . Loosen Handwheel Lock Knob . to turn : 2 . Dust accumulation on tilting or beveling gears . 2 . Clean off tilt and bevel gear assemblies . inside of cabinet . Miter gauge does not 1 . Miter gauge groove and miter gauge bar are 1 . Clean miter gauge groove and bar . move smoothly : dirty . 2 . Adjust set - screws in miter gauge bar . 2 . Set - screws in miter gauge bar are out of adjustment . 1 . Blade is dull . Workpiece binds , 1 . Sharpen or replace blade . burns or stalls motor 2 . Board is warped or twisted . 2 . Replace board . when ripping : 3 . Rip fence is not parallel to blade . 3 . See " Fence Alignment " in Operation and Adjustment Section . Saw blade does not 1 . Blade is dull . 1 . Sharpen or replace blade . cut true at 90 or 45 2 . Indicator arrow is not properly adjusted . 2 . Adjust bevel indicator arrow . degrees : 3 . Positive stops are not set properly . 3 . Adjust 90 and 45 - degree positive stops . Rip fence does not 1 . Rip fence is not mounted properly . 1 . See " Fence Alignment " in Operation and Adjustment Section . move smoothly : 2 . Rails are dirty or sticky . 2 . Clean and apply paste wax to rails . Saw vibrates 1 . Blade is warped . 1 . Replace blade . excessively : 2 . Drive belt is damaged . 2 . Replace drive belt . 3 . Reposition saw on a flat surface . Adjust leveling feet , if 3 . Work surface is uneven . supplied with saw . 4 . Saw is not mounted securely . 4 . Tighten all hardware . 38
Page: 39

10 - iN . TABLESAW MODEL NO . 152.221040 When servicing , use only CRAFTSMAN replacement parts . Use of any other parts may create a HAZARD or cause product damage . Any attempt to repair or replace electrical parts on this table saw may create a HAZARD unless a qualified service technician does repairs . Repair service is available at your nearest Sears Service Center . Always order by PART NUMBER , not by key number . * AVAILABLE AT MOST RETAIL STORES Key No . PART No . Description Qty . Key No . PART No . Description Qty . N / A OR91550 OWNER'S MANUAL - # 22104 10 " Table Saw 1 121 OR91783 PIN 1 / 4 " x 3 / 4 " 1 N / A OR91710 122 OR91774 PAN HEAD SCREW M4 x 10ram 2 BLADE GUARD ASSEMBLY , ( NOT SHOWN ) N / A CONSISTS OF REF # : 1,2 , 3 , 3a , 3b 4 , 5 , 6 , 7 , 16 , 24 & 25 123 OR91080 PLUNGER 1 N / A OR91711 SPLITTER BRACKET ASSEMBLY , ( NOT SHOWN ) 124 OR91081 PLUNGER BLOCK 1 N / A CONSISTS OF REF # : 9 , 9a , 10 , 11 , 12 , 13,14 , 15 & 17 125 OR91082 CURSOR 1 1 OR91785 PUSH NUT ( CHROME ) 126 OR91775 PAN HEAD SCREW M4 x 16ram 1 2 OR91781 PIN 127 OR91776 PAN HEAD SCREW M4 x 20ram 3 3 OR91027 " SEE THRU " BLADE GUARD 127A STD840407 HEX NUT M4 3 3A OR91574 WARNING LABEL 128 OR91756 HEX SOCKET HEAD SCREW M5 x 20ram 2 3B OR91575 WARNING LABEL PICTORAL 129 STD851005 FLAT WASHER M5 2 4 OR91782 PIN 130 OR91673 MITER SCALE 1 5 OR91008 GUARD BRACKET 1 131 OR91084 SPECIAL WASHER , MITER HANDLE 6 OR91834 PUSH NUT ( BLACK ) 132 OR91085 MITER GAUGE KNOB 1 7 OR91745 GUARD SPRING 200 OR91767 JAM NUT 5 / 8 - 18 - LH 1 8 OR91031 SPLITTER MOUNTING ROD 201 OR91020 ARBOR PULLEY 1 9 OR91812 HEX SOCKET HEAD SCREW M6 x 22ram 202 OR91824 KEY 5mm x 5mm x 15mm 1 9A STD852006 LOCK WASHER M6 203 OR91734 BEARING CLOSURE NUT 1 10 OR91011 SPLITTER REAR MOUNT LOWER 203A OR91732 ARBOR SPACER 1 11 OR91051 SPLITTER MOUNT SQUARE NUT 204 OR91733 BALL BEARING < 6203 LLB > 1 12 OR91012 SPLITTER REAR MOUNT UPPER 205 OR91004 ELEVATING BRACKET 1 13 OR91820 SPECIAL FLAT WASHER ( ID : 6.4mm , OD : 18mm ; T : 1.6mm 206 OR91024 ARBOR SLEEVE 1 14 STD852006 LOCK WASHER M6 207 OR91801 WAVE WASHER < BWW 6203 > 1 15 OR91758 HEX SOCKET HEAD SCREW M6 x 16ram 208 OR91733 BALL BEARING < 6203 LLB > 1 16 OR91015 SPLITTER 209 OR91022 ARBOR SHAFT 1 17 OR91048 SPLITTER KNOB 1 210A OR91720 10 " BLADE , 40 TOOTH , A . T . B . , 5 / 8 " BORE 18 OR91760 HEX SOCKET HEAD SCREW M6 x 6ram 211 OR91026 BLADE FLANGE 1 19 OR91820 SPECIAL FLAT WASHER ( ID : 6.4mm , OD : 18mm ; T : 1.6ram 212 OR91050 BLADE HEX NUT - RH 1 20 OR91758 HEX SOCKET HEAD SCREW M6 x 16ram 213 STD836045 HEX HEAD SCREW M10x1 . 5 x 45mm 2 21 OR91010 SPLITTER FRONT MOUNT 214 STD851010 FLAT WASHER M1O 2 21A OR91791 SPRING PIN 3ram x 10ram 215 OR91003 REAR BRACKET 1 22 OR91013 SPLITTER SPRING CLIP 216 STD851010 FLAT WASHER M1O 2 23 OR91753 SPECIAL HEX NUT M12 217 STD852010 LOCK WASHER M10 2 24 OR91795 SPRING PIN 4ram x 22ram 218 STD841015 HEX NUT M10xl . 5 2 25 OR91009 ANTI - KICKBACK FINGER 1 220 OR91721 BELT ( 28 " 6Rib Jsection PoIyV ) 30 OR91789 SET SCREW 1 / 4 - 28 x 3 / 8 " , NYLOCK 221 OR90263 HEX SOCKET SET SCREW M6 x 12mm 1 31 OR91014 TABLE INSERT - STANDARD 222 OR91023 MOTOR PULLEY 1 32 OR91052 TABLE INSERT RETAINING BOLT 223 OR91770 KEY 5mm x 5mm x 36ram 1 33 OR91815 TABLE 224B OR91722 MOTOR ASSEMBLY 1.5 HP 1 34 OR91821 HEX SOCKET SET SCREW M8 x 20ram 224C OR91723 START CAPACITOR 1 35 OR91021 ALIGN - A - CUT INSERT 224D OR91724 RUN CAPACITOR 1 36 STD851008 FLAT WASHER M8 225B OR91576 MOTOR SPEC PLATE 1.5 HP 1 37 STD852008 LOCK WASHER M8 225C OR91576 MOTOR WIRING DIAGRAM LABEL 1 38 STD835030 HEX HEAD SCREW M8x1 . 25 x 30ram 226 STD835030 HEX HEAD SCREW MSx1 . 25 x 30ram 4 39C OR91092 EXTENSION WING 10 " STAMPED STEEL 226A STD851008 FLAT WASHER M8 4 40 OR91817 SPECIAL FLAT WASHER 227 STD861008 FLAT WASHER M8 4 41 STD852008 LOCK WASHER M8 228 OR91001 MOTOR BRACKET 1 42 STD835025 HEX HEAD SCREW M8x1 . 25 x 25ram 229 STD852008 LOCK WASHER M8 4 60 OR91040 SWITCH PADDLE 230 STD840812 HEX NUT M8x1 . 25 4 60A 0R90375 PADLOCK AND KEY 231 OR91825 SPRING PIN 8mm x 35mm 1 61A OR91712 SWITCH ASSEMBLY 232 OR91771 LOCK NUT 1 / 2 - 13UNC 3 63A OR91579 SWITCH RESET LABEL 233 OR91784 PLATE WASHER 1 65 OR91822 SQUARE NUT M6 ( 11mm Square ) 234 OR91802 WAVE WASHER 1 67 STD833012 HEX HEAD SCREW M6 x 12ram 235 OR91064 MOTOR MOUNT STUD 1 114 OR91076 MITER GAGE BODY 236 OR91056 MOTOR SPRING 1 115 OR91077 SPECIAL WASHER , ] - SLOT 237 OR91057 STUD 1 116 OR91074 SPECIAL SCREW 240 OR91790 SHAFT 1 119 OR91079 GUIDE BAR 2 241 OR91757 HEX SOCKET HEAD SCREW M5 x 20mm , NYLOK 120 OR91763 HEX SOCKET SET SCREW M4 x 16ram 39
Page: 40

1O - IN . TABLE SAW MODEL NO . 152.221040 PART No . Key No . PART No . Description Qty . Key No . Description Qty . 243 OR91116 ELEVATING SHAFT ASSEMBLY 416C STD852008 LOCK WASHER M8 2 244 OR91793 SPRING PIN 3ram x 20ram 416D STD851008 FLAT WASHER M8 4 245 STD541231 JAM NUT 5 / 8 - 18 416E OR91164 REAR RAIL 1 248 OR91803 TRUNNION ASSEMBLY 416F OR91809 HEX BUTTON HEAD CAP SCREW M8 x 1.26 x 35ram 2 249 OR91800 WAVE WASHER 416G STD852008 LOCK WASHER M8 4 251 OR91028 RAISE / LOWER SLEEVE 416H STD851008 FLAT WASHER M8 4 252 OR91029 RAISE / LOWER SPACER 417 OR91828 PAN HEAD SELF TAP SCREW M4 x 16ram 4 253 OR91019 POINTER 418 OR91194 1 END CAP , RIGHT HAND 254 OR90059 FLAT WASHER M6 419 OR91705 1 FRONT RAIL WITH SCALE , RIGHT HAND ( 26 " ) ASSEMBLY 255 OR91826 CHEESE HEAD SCREW M6 x 16mm 419A OR91813 SQUARE HEAD SCREW M8 x 35ram 4 N / A OR91804 419B STD840812 HEX NUT M8xl . 28 4 HANDWHEEL ASSEMBLY , ( NOT SHOWN ) CONSISTS OF : 256,256A , 256B & 256C N / A 419C STD852008 LOCK WASHER M8 4 256 OR91045 HANDWHEEL 419D STD851008 FLAT WASHER M8 4 256A OR91041 ELEVATING KNOB ASSEMBLY 420A OR91569 1 SCALE , RIGHT HAND - 25 - inch 256B OR91038 KNOB BOLT 422 OR91764 HEX SOCKET SET SCREW M6 x 10ram 1 256C OR91044 KNOB END CAP 426 OR91196 HANDLE PIVOT SHAFT 1 258 OR91046 HANDWHEEL LOCK KNOB 427 OR91736 CLAMP CAM 1 261 OR91117 TILT SHAFT ASSEMBLY 428 OR91191 FENCE KNOB ASSEMBLY 1 261A OR91793 SPRING PIN 3ram x 20ram 430 OR91812 HEX SOCKET HEAD SCREW M6 x 22mm 2 262 OR91738 ECCENTRIC 431 STD852006 LOCK WASHER M6 2 263 OR91006 FRONT BRACKET 432 OR91830 2 SPECIAL FLAT WASHER ( ID : 6.4 , OD : 186 , T : 1.6 ) 264 STD851010 FLAT WASHER M10 433 OR91739 E - RING # 8 2 265 STD836045 HEX HEAD SCREW M10x1 . 5 x 45ram 434 OR91189 BRACKET 1 266 OR91018 TILT COLLAR 435 OR91188 TENSION CLIP 1 266A OR91740 FIBER WASHER 3 / 8 " 436 STD852006 LOCK WASHER M6 1 268B OR91137 COLLAR 437 OR91755 HEX SOCKET BUTTON HEAD SCREW M6 x 12mm 1 266C OR91762 HEX SOCKET SET SCREW 1 / 4 - 20 X 1 / 4 " 438 OR91731 SPECIAL SCREW M8 x 20mm 2 267 OR91816 HEX SOCKET SET SCREW M6 x 8ram 439 OR91183 HEAD CASTING 1 268 STD840508 HEX NUT M6 439A OR91571 DEBRIS WARNING LABEL 1 268A OR91827 SPECIAL FLAT WASHER ( ID : 5.3 , OD : 18 , T : 3 ) 439B OR91572 LIFTING WARNING LABEL 1 269 OR91017 TILT BRACKET 440 OR91730 SPECIAL PLASTIC SET SCREW M8 x 16ram 2 270 OR91786 ROUND HEAD SCREW M5 x 25ram 441 OR91192 1 END CAP , LEFT HAND 271 OR91045 HANDWHEEL 442 OR91139 1 REAR RAIL ( SHORT ) 271A OR91041 TILTING KNOB ASSY 443 OR91707 1 FRONT RAIL WITH SCALE , LEFT HAND ( 12 " / ASSEMBLY 271B OR91038 KNOB BOLT 443A OR91567 1 SCALE , LEFT HAND - 12 - inch 271C OR91044 KNOB END CAP 444 OR91138 ALIGNMENT BAR 2 273 OR91046 HANDWHEEL LOCK KNOB 445 OR90239 HEX SOCKET SET SCREW M6 X 6ram 8 274 OR91768 , JAM NUT 9 / 16 - 18 446 OR91748 HEX HEAD SCREW M6 X 22mm 2 275 STD851010 FLAT WASHER M10 447 OR91831 INTERNAL TOOTH LOCK WASHER M6 2 276 STD852010 LOCK WASHER M10 448 STD851006 FLAT WASHER M6 2 277 STD841015 HEX NUT M10xl . 6 449 OR91136 GLIDE PAD 2 280 OR91726 BOX END WRENCH 450 STD840610 HEX NUT M6 2 281 OR91727 OPEN END WRENCH 501 OR91200 CABINET ASSY WELDMENT 282 OR90289 2 . Smm ALLEN WRENCH 501A OR91561 SPEC TAG 283 OR90290 3ram ALLEN WRENCH 501B OR91565 BEVEL SCALE 284 OR90291 4ram ALLEN WRENCH 501C OR91560 NAMEPLATE 285 OR91728 5ram ALLEN WRENCH 501D OR91566 BLADE ELEVATION AND TILT LABEL 286 OR91729 6ram ALLEN WRENCH 502 OR91103 HINGE ASSEMBLY 287 OR91808 1 / 8 " ALLEN WRENCH 502A STD840508 HEX NUT M6 4 290 OR91814 CABLE CLAMP 502B STD851005 FLAT WASHER M6 4 291 OR91787 ROUND HEAD TAP SCREW 1 / 4 - 20 x 3 / 8 " 503 OR91787 ROUND HEAD TAP SCREW 1 / 4 - 20 x 3 / 8 " 3 N / A OR91714 FENCE ASSEMBLY ( NOT SHOWN ) CONSISTS OF : 504 OR91123 MOTOR COVER 1 404 , 405,406 , 406A , 407,408 , 409,410 , 411,412,413,414 , 504A OR91564 WARNING LABEL 1 422,426,427 , 428,430 , 431,432,433 , 434,435 , 436,437 , 505 OR91777 PAN HEAD SCREW M5 X 15ram 4 N / A 438 , 439,439A , 439B , 440,446 , 447,448,449 & 450 506 OR91058 LATCH BLACK SWELL ASSEMBLY 2 404 OR91828 PAN HEAD SELF TAP SCREW M4 x 16ram 527 OR91134 WRENCH HOOK 1 405 OR91168 FENCE TOP 528 OR91135 FENCE HOOK 2 405A OR91570 CRAFTSMAN LABEL , VERTICLE 529 OR91832 SHEET METAL SCREWS M4 x 8mm 6 406 OR91169 FENCE END CAP 529A OR91832 TRIANGLE TAP SCREW M4 x 8ram 2 408A OR91764 HEX SOCKET SET SCREW M5 x 10ram 530 OR91177 LEG ASSEMBLY WELDMENT 2 408B OR91828 PAN HEAD SELF TAP SCREW M4 x 16ram 531 OR91174 RUBBER FOOT PAD 4 407 OR91199 FENCE HOLD DOWN 534 STD840812 HEX NUT M8xl . 25 8 408 OR91197 PIVOT PIN 535 STD852008 LOCK WASHER M8 8 409 OR91198 PIVOT BUSHING 536 STD851008 FLAT WASHER M8 8 410 OR91162 FENCE EXTRUSION 539 OR91179 TIE BAR 2 411 OR91761 HEX SOCKET HEAD SCREW M8x1 . 25 x 25ram 540 OR91181 CARRIAGE HEAD SCREW 5 / 16 - 18 x 5 / 8 " 8 411A OR90311 FLAT WASHER M8 541 STD551031 FLAT WASHER 5 / 16 " 8 412 OR91778 PAN HEAD SCREW M5 x 16mm 542 STD551131 LOCK WASHER 5 / 16 " 8 413 OR90462 FLAT WASHER M6 543 STD541031 HEX NUT 5 / 16 " - 18 8 414 OR91182 CURSOR 544 STD835025 HEX HEAD SCREW M8xl . 26 x 26mm 8 415 OR91195 REAR RAIL CONNECTOR 545 STD851008 FLAT WASHER M8 8 416A OR91806 HEX BUTTON HEAD CAP SCREW M8 x 1.25 x 25mm 416B STD840812 HEX NUT M8xl . 26 40
Page: 41

? Z _ D p . m 39c ( 2 ) . - - . fj _ 3a ( 81 @ 37 ( 8 ) / - 38 ( 8 ) J * ( 2 ) 25 ( 2 , 223 65 ( 2 > 122 ( 2 ) 0 7 ( 2 ) ill F - Z . o o4 _ o
Page: 42

? Z Wr " m bO 282 _ 83 0 _ 84 mr - 285 a _ 6 z P o o
Page: 43

oZ W m 60 441 487 485A 409 ( 2 ) 443A 410 439B ( 4 ) ( 4 ) 4 £ 0A ( 4 ) 0 I " TI Z 418 P I , O o o
Page: 44

%
Page: 45

anuai dei Proprietario CRRFr MRH 1.5 caballos de fuerza ( servicio continuo ) 2 caballos de fuerza ( ma × imo desarrollado ) 3450 R . P . M . ( R . P . M . sin carga ) de 1 puig . No . de Modelo 152.221040 ! L [ nea de Ayuda al Cliente PRECAUCION : PARA SU SEGURIDAD PERSONAL ; 1 - 800 - 897 - 7709 Lea y obedezca todas las Instrucciones Sirvase tenet listo su No . de de Seguridad y Funcionamiento antes Modelo y No . de Serie . de accionar esta Sierra de Mesa . Sears , Roebuck and Co . , Hoffman Estates , IL 60179 U . S . A . No . de Pieza OR91550 Revisado : REV . D 45
Page: 46

SECCl0N PAGINA Garantfa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Especificaciones del producte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Glesario de t _ rminos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Instrucciones de seguridad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Directrices para las e × tensiones el _ ctricas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Instrucciones de conexi6n a tierra . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Instrucciones especfficas de seguridad para las sierras de mesa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Accesorios y aditamentos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Contenido de la caja . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Conozca su sierra de mesa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Instrucciones de montaje . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Operaciones y ajustes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Mantenimiento . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Guia de Iocalizaci6n de averias . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Infermaci6n de servicio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 GARANT [ A COMPLETA DE UN ANO Si este producto Ilegara a fallar debido a defectos materiales o de elaboraci6n dentro de un aRo desde la fecha de compra , devuelvalo a su Centro de Servicio Sears mas cercano para repararlo sin costo alguno . Si se hace uso de este producto para fines comerciales o de alquiler , esta garantia se aplica s61o por espacio de 90 d [ as desde la fecha de compra . Esta garantia le concede derechos legales especfficos , y tambien podr _ tener otros derechos que variaran de un estado a otro . Sears Roebuck and Co . , Dept 817 WA , Hoffman Estates , IL 60179 Tipo de motor Inducci6n Mesa frente a la hoja a HP de servicio continuo 1.5 la profundidad maxima de corte 12 - 1 / 2 pulg . HP mb , ximo desarrollado 2 Ancho maximo de la Amperios 15 / 7.5 fresa rotativa de ranurar 13 / 16 pulg . Voltios 120 / 240 Diametro maximo de la Hertz 60 hoja de fresa rotativa 8 pulg . RPM 3450 R . RM . ( R . P . M . sin carga ) Ala de mesa Inclinaci6n de la hoja Inclinaci6n izquierda zquierda y derecha 8 pulg . , hacero estampado Marcha de la hoja Correa Poly - V Peso de la sierra de mesa 350 Ibs . Diametro de la hoja 10 pulg . Eje de la hoja 5 / 8 pulg . Numero de dientes 40 Velocidad de la hoja 3450 R . RM . Haga uso de la protecci6n de circuitos correcta para evitar los choques electricos a sf mismo y el daRo a la Sierra de Mesa . Tipo de guia Guia y rieles de enclavamiento No la exponga a la Iluvia ni haga uso de ella en entornos frontal de aluminio extruido humedos . Profundidad maximae de corte a 90 grados 3 - 3 / 8 pulg . La Sierra de Mesa viene cableada de fabrica para el fun - Profundidad maxima cionamiento a 120 V , 60 Hz . Conectar a un circuito ramal de de corte a 45 grados 2 - 1 / 4 pulg . 120 V , 15 amperios y utilice un fusible o disyuntor de circuitos de retardaci6n de tiempo de 15 amperios . El circuito electrico Corte a Io largo maximo no podr & tener un tama5o de cable menor al # 14 . Para evitar a la derecha de la hoja 25 pulg . choques o incendios , reponga el cord6n de energia inmedia - Corte a Io largo maximo tamente siesta da5ado en cualquier manera . a la izquierda de la hoja 12 pulg . 46
Page: 47

Alefriz - Muesca cuadrada en el borde del material . Fresa rotativa de ranurar - Corte no directo que produce una muesca cuadrada . Una fresa rotativa tiene , tfpicamente , un ancho de 1 / 8 a 13 / 16 pulg . Una fresa rotativa requiere un Contragolpe - Cuando el material es arrojado hacia el conjunte especial de hojas que no estan incluidas con esta operario durante una operaci6n de corte en el momento que sierra de mesa . el material hace contacto inicial con la hoja , o si el material hace constricci6n sobre la hoja . Los contragolpes son pelf grosos y pueden resultar en heridas graves . Goma , alquitr _ in o resina - Residuo pegajoso y basado en la savia producido por los productos de madera . Corte a Io largo - La operaci6n de hacer un corte a Io largo del grano del material . Gradaci6n de la hoja de la sierra - La distancia en que las puntas de la hoja de la sierra estan anguladas hacia afuera desde el grosor de la hoja . La gradaci6n de los dientes de la Corte compuesto - La operaci6n de hacer cortes tanto de hoja de la sierra permite que el cuerpo de la hoja atraviese biselado come de ingletes a la misma vez . todos los cortes con seguridad . Corte de biselado - La operaci6n de realizar cualquier corte Ladeo - El mal alineamiento de la hoja con las ranuras de con el conjunto de hojas en cualquier grade que no sea ingletes , o cuando la hoja no esta paralela con las ranuras de 90 grados . ingletes . Corte de ingletes - La operaci6n de hacer un corte Mano libre - Una operaci6n muy peligrosa para efectuar un utilizando la escuadra de ingletes a cualquier angulo que corte sin hacer uso de la gufa de corte ni la escuadra de no sea de cero grades . ingletes durante una operaci6n de corte . Los cortes a mano libre jam _ s deben realizarse con una Sierra de Mesa . Corte repetido - La operaci6n de realizar un corte para reducir el grosor del material . Mesa / zona de trabajo - La superficie total de la parte superior de la sierra de mesa sobre la que descansa el material mientras que se realizan operaciones de montaje o Corte transversal - La operaci6n de realizar un corte a Io de certe . ancho del grano o el ancho del material . Refrentado - Dispositivo accesorio que puede hacerse o Dedos anti - contragolpe - Dispositivo de seguridad comprarse para ayudar a la gufa o sujetar un material durante conectado al protector de hoja y al ensamblado del hendidor las operaciones de corte . dise5ado para evitar la expulsi6n de un material durante las operaciones de corte . Trayecto de la hoja de la sierra - La zona que est _ directa - mente en Ifnea con la hoja , incluyendo la zona per encima , Eje - El eje sobre el cual esta montada la hoja o la herra - por debajo y per delante de la misma . mienta cortante de accesorio . Vara de empuje - Dispositivo accesorio que puede hacerse o Entalladura - La pieza removida del material per la hoja comprarse para ayudar a empujar el material a traves de la durante cualquier operaci6n de corte . hoja . Se hace use de una vara de empuje para evitar que las manos del operario entren en contacto con la hoja durante el corte a Io largo de materiales angostos . 47
Page: 48

9 . INSTRUCCIONES GENERALES DE UTILICE PROTECCION OCULAR SIEMPRE . Cualquier herramienta mecanica puede arrojar escombros hacia los SEGURIDAD ojos durante el funcionamiento , pudiendo esto resultar en El funcionamiento de una Sierra de Mesa puede resultar heridas oculares graves y permanentes . Los anteojos de peligroso si se hace caso omiso de la seguridad y del sentido uso cotidiano NO son gafas de seguridad . Utilice Gafas com0n . El operario debe estar familiarizado con el fun - de Protecci6n SIEMPRE ( que cumplan con la normativa cionamiento de la herramienta . Lea este manual para enten - Z87 . 1 de ANSI ) durante la operaci6n de herramientas der su Sierra de Mesa . NO OPERE esta Sierra de Mesa si no mec & nicas . Las Gafas de Protecci6n est & n disponibles entiende plenamente las limitaciones de dicha herramienta . en las tiendas Sears de ventas al detal . El equipo auditi - NO haga modificaciones de ning0n tipo a esta Sierra de vo debe cumplir con la Normativa $ 3.19 de ANSI . Mesa . RECUERDE : Usted es responsable de su propia seguridad . ANTES DE UTILIZAR LA SIERRA DE MESA 10 . SIEMPRE DESENCHUFE LA HERRAMIENTA DEL TOMACORRIENTES cuando vaya a realizar ajustes , Para evitar las heridas graves y el dare a la herramienta , lea cambiar piezas o realizar cualquier clase de manteni - y obedezca todas las instrucciones de Seguridad y Operaci6n miento . antes de operar la Sierra de Mesa . MANTENGA LOS ESCUDOS DE PROTECCION EN SU 11 . 1 . LEA a conciencia el Manual del Propietario . APRENDA SlTIO Y EN BUEN ESTADO DE FUNCIONAMIENTO . a c6mo hacer use de esta herramienta para sus aplicaciones diseRadas . 12 . EVITE EL ARRANQUE ACCIDENTAL . Asegurese de que el interrupter de potencia se encuentre en la posici6n 2 . CONECTE TODAS LAS HERRAMIENTAS A TIERRA . de " APAGADO " antes de enchufar el cord6n de potencia Si la herramienta se suministra con un enchufe de 3 en el tomacorrientes . machos , se le debe enchufar a un tomacorrientes que disponga de 3 contactos electricos . El tercer macho se 13 . QUITE TODAS LAS HERRAMIENTAS DE MANTENI - utiliza para conectar la herramienta a tierra y ofrecer MIENTO de la zona inmediata antes de encender la protecci6n contra los cheques electricos accidentales . herramienta . NO quite el tercer macho . Vea las Instrucciones de Conexi6n a Tierra . 14 . SOLO UTILICE ACCESORIOS RECOMENDADOS . El use de accesorios incorrectos o poco apropiados puede 3 . EVITE UN ENTORNO LABORAL PELIGROSO . NO ocasionar heridas graves al operario y ocasionar dare a utilice las herramientas eleetricas en un entorno h0medo , la herramienta . Si tiene dudas , consulte el manual de ni tampoco las exponga a Iluvia . instrucciones que se adjunta con el accesorio especffico . 4 . NO utilice herramientas electricas si hay gases o Ifquidos JAMAS DEJE UNA HERRAMIENTA EN FUNCIONA - 15 . inflamables presentes . MIENTO SIN ATENDER . Conmute el interruptor de energfa a la posici6n de apagado . NO abandone la 5 . MANTENGA SIEMPRE su zona de trabajo limpia , bien herramienta hasta que esta se haya detenido per alumbrada y organizada . NO TRABAJE en un entorno complete . con superficies de piso resbalosas a consecuencia de los escombros , la grasa y la cera . 16 . NO SE PARE SOBRE LA HERRAMIENTA . Pueden pro - ducirse heridas graves si la herramienta se vuelca o si 6 . MANTENGA ALEJADOS A LOS NINOS Y VISITANTES . usted hace contacto con la herramienta accidentalmente . NO permita que haya personas en la zona inmediata de trabajo , particularmente cuando la herramienta electrica 17 . NO ALMACENE nada por encima ni cerca de la maquina se encuentre en funcionamiento . en donde alguien pueda intentar pararse en la herra - mienta para alcanzarlo . 7 . NO DEBE FORZAR LA HERRAMIENTA a realizar operaciones para las que no fue diseRada . Realizar & una 18 . MANTENGA SU EQUILIBRIO . NO se extienda sobre la labor m & s segura y de mejor calidad si se le utiliza para herramienta . Haga use de zapatos con suela de caucho realizar operaciones para las que fue diseRada . resistente al aceite . Mantenga el piso libre de escombros , grasa o cera . 8 . UTILICE VESTIMENTA APROPIADA . NO vista ropa holgada , guantes , corbatas ni artfculos de joyerfa . Estos 19 . MANTENGA SUS HERRAMIENTAS CUIDADOSA - artfculos pueden quedar atrapados en la maquina MENTE . Mantenga sus herramientas limpias yen buen durante las operaciones y tirar del operario , atrayendolo estado . Mantenga afiladas todas las hojas y brocas . haeia las piezas en movimiento . El usuario debe Ilevar una cubierta protectora sobre el cabello , si tiene cabellera larga , para impedir el contacto con cualquier pieza en movimiento . 48
Page: 49

20 . REVISE SI HAY PIEZAS DA _ IADAS ANTES DE CADA DIRECTRICES PARA USO DE LA HERRAMIENTA . Revise todos los protec - LAS EXTENSIONES ELleCTRICAS tores cuidadosamente para comprobar que funcionan correctamente y que no estan dahados , y que realizan Mientras menor sea el n0mero de calibre , mayor sera el sus funciones diseRadas correctamente . Revise el diametro de la extensi6n electrica . Si tiene dudas sobre las alineamiento , la fijaci6n o la ruptura de las piezas en dimensiones correctas de una extensi6n electrica , utilice un movimiento . Cualquier protector u otra piezas que se cord6n mas corto y mas grueso . Una extensi6n de dimen - encuentre daRada debe repararse o reemplazarse siones insuficientes producira una caida en el voltaje de linea , inmediatamente . resultando en una perdida de potencia y el sobrecalenta - miento . SOLO UTIMCE UNA EXTENSION ELC : CTRIOA DE 3 21 . HAGA SU TALLER A PRUEBA DE NIl _ lOS quitando las HILOS QUE DISPONGA DE UN ENCHUFE DE CONEXION Ilaves del interrupter , desenchufando las herramientas de A TIERRA DE 3 MACHOS , Y UN RECEPTACULO DE 3 los tomacorrientes y haciendo uso de candados . POLOS QUE ACEPTE EL ENCHUFE DE LA M , _ , QUINA . 22 . NO OPERE LA HERRAMIENTA BAJO LA INFLUENClA Siesta haciendo use de una extensi6n electrica a la intern - DE LAS DROGAS O DEL ALCOHOL . perle , este seguro de que la extensi6n se encuentre marcada con " W - A " ( " W " en el CanadA ) , Io que indica que su use a la 23 . AFIANCE TODO EL MATERIAL . Siempre que resulte intemperie es aceptable . posible , utilice abrazaderas o plantillas para asegurar el material . Esto ofrece mayor seguridad que intentar Aseg0rese de que las dimensiones de su extensi6n electrica sujetar el material con sus propias manes . sean las correctas y que se encuentre en buen estado electrico . Repare siempre una extensi6n electrica daRada , 24 . MANTI _ NGASE ALERTA , ESTI _ CONSClENTE DE LO o procure que una persona experta la repare antes del use . QUE HACE , Y UTILICE SENTIDO COMON CUANDO VAYA A OPERAR UNA HERRAMIENTA MEC , _ , NICA . Proteja sus extensiones electricas contra los objetos filosos , NO UTILICE LA HERRAMIENTA SI ESTA CANSADO O el calor en exceso y de los lugares mojados o h0medos . BAJO LA INFLUENClA DE DROGAS , ALCOHOL O MEDICAMENTOS . Un momento de descuido durante el uso de herramientas electricas puede resultar en lesiones personales graves . FUNCIONAMIENTO A 120 VOLTIOS SOLAMENTE 25 . El use de esta herramienta puede generar y dispersar 25 PiES DE 50 PIES DE 100 PIES DE polvo u otras partfculas aereas , incluyendo polvo de LARGO LARGO LARGO madera , polvo de silice cristalino y polvo de asbesto . 18AWG 16AWG 16AWG Dirija las part [ culas en la direcci6n opuesta a la cara y el 0 a 6 Amperios cuerpo . Opere la herramienta siempre en un lugar con 18AWG 16 AWG 14 AWG 6 a 10 Amperios buena ventilaci6n y proporcione la eliminaci6n correcta de polvo . Utilice un sistema de recolecci6n de polvo 16AWG 16AWG 14 AWG 10 a 12 Amperios siempre que sea posible . La exposici6n al polvo puede 14 AWG 12 AWG No se 12 a 15 Amperios ocasionar dare respiratorio grave y permanente u otros recomienda dares , incluyendo silicosis ( una enfermedad pulmonar grave ) , cancer y la muerte . Evite respirar el polvo y evite el contacto prolongado con el polvo . El permitir la entrada del polvo en su boca u ojos , o dejar que permanezca sobre su piel , podra promover la absorci6n de materiales daRinos . Utilice siempre la protecci6n respiratoria NIOSH FUNCIONAMIENTO A 240 VOLTIOS SOLAMENTE / OSHA que sea apropiada para la exposici6n al polvo y lave las zonas afectadas con jab6n y agua . 25 PIES DE 50 PIES DE 100 PIES DE LARGO LARGO LARGO 26 . UTILICE UNA EXTENSION ELI _ CTRICA CORRECTA Y EN BUEN ESTADO . Cuando vaya a hacer uso de una 18AWG 18AWG 16 AWG 0 a 6 Amperios extensi6n electrica , aseg0rese de utilizar una que sea Io 18AWG 18 AWG 14 AWG 6 a 10 Amperios suficientemente fuerte come para transportar la corriente a ser utilizada per su herramienta . Tenga la bondad deDO 16AWG 16 AWG 14 AWG 10 a 12 Amperios referirse a la tabla " CALIBRE MJNIMO RECOMENBA 14 AWG 12 AWG No se PARA LAS EXTENSIONES ELI _ CTRICAS ( AWG ) " para 12 a 15 Amperios recomienda el dimensionamiento correcto de la extensi6n electrica . Si tiene dudas , utilice la siguiente extensi6n de mayor calibre . 27 . DIRECCION DE LA ALIMENTACION . Alimente el material hacia la hoja o cortadora s61o contra el sentido de la rotaci6n de la hoja o cortadora . 49
Page: 50

REPONGA CUALQUIER CORDON DAI _ IADO O GASTADO ESTA HERRAMIENTA DEBE ESTAR CONECTADA A TIERRA DURANTE EL USO PARA PROTEGER AL INMEDIATAMENTE . OPERARIO CONTRA LOS CHOQUES ELECTRICOS . PARA LAS MAQUINAS CONECTADAS A TIERRA Y CON EN EL CASO DE UN MALFUNCIONAIVllENTO O AVERiA , la CORDON DISEI _ IADAS PARA EL USO EN UN CIRCUITO conexi6n a tierra ofrece el trecho de menor resistencia para la DE SUMINISTRO CON UNA POTENCIA DE RFtGIMEN corriente electrica y reduce el riesgo de los choques electri - MENOR A LOS 150 VOLTIOS . cos . Esta herramienta viene equipada con un cord6n electrico que dispone de un conductor de conexi6n a tierra para el equipo asf como un enchufe de conexi6n a tierra . El enchufe Esta herramienta esta diseRada para el uso en un circuito DEBE estar enchufado a un tomacorrientes coincidente que que disponga de un tomacorrientes como el que se ilustra en haya sido correctamente instalado y conectado a tierra de la FIGURA " IA " . La FIGURA " IA " muestra un enchufe elec - acuerdo con TODOS los c6digos y ordenanzas municipales . trico de 3 hilos y un tomacorrientes electrico con conductor de conexi6n a tierra . Si no se encuentra disponible un toma - corrientes debidamente conectado a tierra , se puede hacer NO MODIFIQUE EL ENCHUFE SUMINISTRADO . Haga que uso de un adaptador , segun Io ilustrado en la FIGURA " IB " , un electricista calificado instale el tomacorrientes apropiado si para conectar dicho enchufe provisionalmente al toma - el enchufe no cabe en el tomacorrientes . corrientes de 2 contactos que no est & conectado a tierra . El adaptador cuenta con una orejeta rfgida que DEBE ser conectada a una conexi6n a tierra permanente , tal como Io es LA CONEXION ELI _ CTRICA INCORRECTA del conductor de una caja de tomacorrientes debidamente conectada a tierra . conexi6n a tierra para el equipo puede resultar en el riesgo SE PROHiBE EL USO DE ESTE ADAPTADOR EN EL de choques electricos . El conductor con el aislamiento verde CANADb , . ( con o sin rayas amarillas ) es el conductor de conexi6n a tierra para el equipo . NO conecte el conductor de conexi6n a tierra para el equipo a una terminaci6n viva si resulta nece - PRECAUCION : En todos los casos , aseg0rese de que el sario reparar o reemplazar el cord6n electrico o el enchufe . tomacorrientes en cuesti6n este debidamente conectado a tierra . Si no esta seguro , haga que un electricista certificado revise el tomacorrientes . CONSULTE con un electricista calificado o personal de servicio si no entiende las instrucciones de conexi6n a tierra completamente , o si no esta seguro que la herramienta esta El motor suministrado con su Sierra de Mesa es un motor debidamente conectada a tierra . monofb . sico de voltaje doble , 120 / 240 voltios . Si desea operar su sierra de mesa a 240 voltios , sera necesario reconectar los avances del motor dentro de la caja de empalmes del El motor suministrado con su Sierra de Mesa es un motor motor , siguiendo el diagrama de cableado que aparece en la monofasico de corriente alterna y voltaje doble de 120 / 240 cubierta de la caja de empalmes . voltios , 60 hertzios . Se envfa cableado para las aplicaciones a 120 voltios . Jamas conecte el alambre verde ( de tierra ) a un terminal vivo . ASEGORESE de que el motor este desconectado de la SOLO UTILICE UNA EXTENSION ELC : CTRICA DE 3 HILOS fuente de energfa antes de reconectar los avances del motor . QUE DISPONGA DE UN ENCHUFE DE CONEXION A TIERRA DE 3 IVlACHOS , Y UN RECEPTACULO DE 3 POLOS QUE ACEPTE EL ENCHUFE DE LA MAQUINA . Fig . 1A Fig . 1B orejeta del adaptador 120 VOLTIOS 120 VOLTIOS de conexi6n a tierra conductor de conexi6n conductor de conexi6n a tierra a tierra ( _ tomacorrientes para tres tomacorrientes para machos dos machos cord6n el _ sctrico cord6n el _ ctrico de tres hilo de tres hilos 50
Page: 51

ASEGURESE de que las mascaras o respiradores tienen Tambien serA necesario reemplazar el enchufe de 120 voltios suministrado con el motor per un enchufe clasificado per aprobaci6n MSHA / NIOSH . UL / CSA come apropiado para los 240 voltios y la corriente clasificada de la sierra . Comunfquese con un electricista local El funcionamiento de cualquier sierra de mesa puede tener competente acerca de los procedimientos correctos para come consecuencia la expulsi6n de escombros hacia sus instalar el enchufe . La sierra de mesa debe cumplir con todos ojos , Io que puede resultar en heridas oculares graves . los c6digos electricos en el ambito local y nacional tras la UTILICE SIEMPRE Gafas de Protecci6n ( que cumplan con la instalaci6n del enchufe de 240 voltios . normativa Z87 . 1 de ANSI ) cuando vaya a hacer use de la sierra de mesa . Las Gafas de Seguridad estan disponibles en La sierra de mesa con el enchufe de 240 voltios s61o debe las tiendas Sears de ventas al detal . Mantenga los pulgares y conectarse a un tomacorrientes que disponga de la misma los dedos alejados de la hoja mientras que esta se encuentre configuraci6n que el enchufe ilustrado en la Figura " 1C " . No girando . hay adaptadores disponibles para el enchufe de 240 voltios ni tampoco debe usarse ninguno . Fig . 1 C tomacorrientes conectado a tierra Debe observar siempre las precauciones basicas cuando 240 VOLTIOS machos utiliza su Sierra de Mesa . Para reducir el riesgo de lesiona - portadores miento , cheque electrico o incendio , cumple con las reglas de de corriente seguridad que siguen : © 1 , LEA y entienda el manual de instrucciones antes de poner la sierra de mesa en funcionamiento . e 2 . NO OPERE ESTA MAQUINA hasta que se encuentre ensamblada e instalada conforme a las instrucciones . © 3 . ASESORESE CON SU SUPERVISOR , instructor u otra el macho de conexidn a persona experta si no esta familiarizado con el use de tierra es el mdtslargo de esta maquina los 3 machos 4 , NO PERMITA que la sierra de mesa permanezca enchu - fada al tomacorrientes . La sierra de mesa debe desen - chufarse del tomacorrientes cuando no se encuentre en use y antes de rendir servicie , cambiar hojas y limpiar . ASEGURESE de que el tomacorrientes en cuesti6n este debidamente conectado a tierra . Si no esta seguro , haga que 5 . COLOQUE el interrupter de energfa en " APAGADO " un electricista competente revise el tomacorrientes . antes de desenchufar la sierra de mesa . 6 . PARA REDUCIR EL RIESGO DE CHEQUES ELleCTRI - COS , no utilice la sierra a la intemperie . No la exponga a La Sierra de Mesa es para el use en interiores exclusiva - la Iluvia . Almacenela puertas adentro . mente . No la exponga a la Iluvia , ni haga use de ella en lugares ht _ medos . 7 , OBEDEZCA todos los c6digos electricos y de seguridad , incluyendo el C6digo Electrico Nacional ( NEC ) y las INSTRUCCIONES DE SEGURIDAD Normas de Salud y Seguridad en el Trabajo ( OSHA ) . Todas la conexiones y cableado electrico deben ser ESPECiFICAS PARA LAS SIERRAS realizadas s61o per personal competente . DE MESA 8 , NO manipule el enchufe ni la sierra de mesa con las manes mojadas . REGLAMENTO " PROPOSITION 65 " DE CALIFORNIA UTILICELA s61o come se describe en este manual . 9 . Utilice accesorios recomendaos per Sears solamente . 10 . JAMAS tire de la Sierra de Mesa per su cord6n de EL POLVO GENERADO MEDIANTE LIJADO MEC _ , NICO , energ [ a . NUNCA permite que el cord6n de energia entre ASERRADO , RECTIFICACION , PERFORACION Y OTRAS en contacto con bordes filosos , superficies calientes , ACTIVIDADES DE CONSTRUCCJON contiene productos aceite o grasa . qufmicos conocidos come fuentes de cancer , defectos de nacimiento u otros dares reproductivos . AIgunos ejemplos 11 . NO desenchufe la sierra de mesa tirando del cord6n de de estos qufmicos incluyen los siguientes : energfa . AGARRE siempre el enchufe y no el cord6n . • plomo proveniente de pinturas con base de plomo , o silice cristalino de ladrillos y cemento y otros productos de 12 . REPONGA un cord6n daflado inmediatamente . NO mamposterfa , y utilice un cord6n o enchufe que esten da5ados . Si la • arsenico y creme de las maderas tratadas con qufmicos . sierra de mesa funciona debidamente , o si ha side Su riesgo proveniente de dichas exposiciones podrA variar da5ada , dejada a la intemperie o si ha entrado en contac - segtin que tan a menudo realice dicha clase de trabajo . Para to con el agua , devuelvala a un Centre de Servicio Sears . reducir su exposici6n a estos qufmicos : trabaje en un sitio que goce de buena ventilaci6n y trabaje con equipo de 13 . NO utilice la sierra de mesa come juguete . NO LA seguridad aprobado , tal come las caretas de polvo diseSadas UTIMCE si hay niBos presentes . especialmente para filtrar las partfculas microsc6picas . 51
Page: 52

27 . JAMAS realice labores de trazado , ensamblado o men - 14 . La Sierra de Mesa esta diseRada para el use dom4stico o el use comercial ligero SOLAMENTE . taje sobre la mesa / zona de trabaje cuande la maquina se encuentre en funcionamiento . 15 . CONECTE la sierra de mesa a un tomacorrientes debidamente conectado a tierra . Vea las instrucciones de 28 . JAMAS reestablezca el bot6n de sobrecarga termica sin conexi6n a tierra . haber apagado antes la sierra de mesa . 29 . 16 . UTILICE SlEMPRE los protectores cuando resulte APOYE los materiales largos o anchos correctamente . posible hacerlo . Revise que esten en su sitio , afianzades 30 . y funcionando correctamente . APAGUE LA SIERRA y desenchL ] fela de la fuente de energfa . Limpie la mesa / zona de trabajo antes de 17 . EVITE LOS CONTRAGOLPES haciendo Io siguiente : abandonar la sierra . BLOQUEE el interruptor de ARRANQUE / PARADA ( START / STOP ) con el candado • Manteniendo la hoja afilada y libre de oxidaci6n y suministrado para impedir el uso desauterizado . alquitr _ n . • Manteniendo la gufa de corte a Io largo paralela con la 31 . POSICIONE SlEMPRE la gufa auxiliar per Io menos 2 heja de la sierra . pulgadas en frente de la hoja de la sierra cuando vaya a • Usande el protector de la hoja de la sierra y el ensam - usar la gufa auxiliar come tope de parada durante el blade del hendidor para todas las eperaciones posibles , corte transversal . incluyendo el aserrado directo . • Empujando el material mas all & de la hoja de la sierra 32 . El ala de extensi6n derecha DEBE ESTAR plenamente antes de soltarlo . ensamblado y la cubierta del motor debe estar cerrada y • No cortando a Io largo jam & s ningun material que este afianzada antes de que se conecte la sierra de mesa a la torcido o alabeado , o que no disponga de un borde fuente de energfa . recto para guiarlo a Io largo de la gufa de corte . 33 . INFORMACION ADIClONAL sobre el funcionamiento • Usando tablas de refrentado cuando no pueda utilizarse seguro y correcto de este producto est & disponible de el protector de hoja y el ensamblado del hendidor . parte del National Safety Council , 1121 Spring Lake • No aserrande jamb . s una pieza de material grande que Drive , Itasca , IL 60143 - 3201 en el Manual de Prevenci6n no pueda controlarse . de Accidentes para Operaciones Industriales asf como • No usando jamas la guia durante el corte transversal . en las Hojas de Dates de Seguridad suministradas por • No aserrando jamAs un material con nudos sueltos u el NSC . Tenga la bondad de referirse tambien a los otras imperfecciones . Requisitos de Seguridad para la Maquinaria de Ebanisterfa ANSI 01.1 de la American National Standards 18 . RETIRE las piezas troceadas y los escombros de la Institute y el Reglamento OSHA 1910.213 del U . S . mesa antes de arrancar la sierra . La vibraci6n de la Department of Labor . sierra puede hacer que se muevan hacia la hoja de la 34 . GUARDE ESTAS INSTRUCCIONES . Refierase a elias sierra , expulsandolas . Despues de realizar el corte , apague la sierra . Cuando la hoja se haya detenido por con frecuencia y utilfcelas para instruir a los demos . completo , desenchufe la sierra y retire los escombros . 19 . JAMAS ARRANQUE la sierra con el material contra la Las fuentes que aparecen a continuaci6n tienen informaci6n hoja . disponible acerca de la venta y funcionamiento correcto de esta herramienta : 20 . JAMAS realice operaciones " a mane libre " . Haga use de la gufa de corte o de la gufa de ingletes para orientar y Power Tool Institute guiar el material . Sujete el material firmemente contra la 1300 Summer Avenue escuadra de ingletes o la gufa de corte . Cleveland , OH 44115 - 2851 www . powertoolinstitute . org 21 . UTILICE una varilla o varillas de empuje para cortar materiales angostos a Io largo . National Safety Council 1121 Spring Lake Drive 22 . EVITE OPERACIONES Y POSICIONES MANUALES Itasca , IL 60143 - 3201 TORPES en las que un deslizamiento repentino puede hacer que su mano haga contacto con la hoja de la American National Standards Institute sierra . 25 West 43rd Street 4th floor 23 . MANTENGA brazos , manes y dedos alejados de la hoja . New York , NY 10036 www . ansi . org 24 . JAMAS ponga ninguna parte de su cuerpo en Ifnea con el trayecto de la hoja de la sierra . ANSI 01.1 Safety Requirements for Woodworking Machines ( Requisites de Seguridad para la Maquinaria de 25 . JAM _ , S intente alcanzar alrededor ni por encima de la Ebanisterfa ANSI 01.1 ) y los reglamentos del U . S . hoja . Department of Labor www . osha . gov 26 . JAMAS intente liberar una hoja atascada sin primero apagar y desenchufar la hoja de la fuente de energfa . 52
Page: 53

ACCESORIOS DiSPONiBLES Sears podrarecomendarotros accesorios nolistados en este manual . Visite su Departamento de Ferreteffa de Sears o consulte el Consulte su Departamento de Ferreteffa de Sears mas cer - Catalogo de Herramientas Electricas y de Mano de Sears cano o el Catalogo de Herramientas Electricas y de Mano de para los siguientes accesorios : Sears para otros accesorios . ARTJCULO NOMERO DE EXiSTENCiA No utilice ning0n accesorio a menos que haya lefdo cabal - * Guia Auxiliar , mente el Manual del Propietario para dicho accesorio . 29878 Gufa de Corte a Io Largo * Extensi6n y Tope de Parada 29879 de la Escuadra de Ingletes * Abrazadera de Material , $ 61o utilice accesorios recomendados para esta Sierra de Escuadra de Ingletes 29880 Mesa . El uso de otros accesorios puede ocasionar lesiones * Conducto de Polvo con Puerto de Polvo 22102 graves y producir daffo a la Sierra de Mesa . * Ensamblado de Micro - Ajuste 29881 * Inserci6n de Mesa - Estandar 29882 * Inserci6n de Mesa - Fresa Rotativa 29885 * Inserci6n de Mesa - Cabezal de Corte para Moldura 29887 * Hoja de Sierra - Leitz ; Hoja de Paso Variable , 10 pulg . x 40 dientes 29888 * Sistema de Gufas 32371 CONSTRUYENDO UNA TABLA DE B [ SELADO Fig . 2A 24 " I La entalladura debe guardar una distancia aproximada de 1 / 4 de pulg . 14 s - [ Fig . 2B La Figura 2A ilustra las dimensiones para hacer una tabla de biselado tfpica . El material del cual esta hecho la tabla de biselado debe ser una pieza de madera recta que este libre de nudos y grietas . Las tablas de biselado se utilizan para mantener el trabajo en contacto con la gufa y la mesa para impedir los contragolpes . Afiance la tabia de biselado a la gufa y la mesa de manera que el borde delantero de la tabla de biselado apoye el material hasta que se haya realizado el corte . Utilice tablas de biselado para todas las operaciones de corte que no sean de paso y en las que debe retirarse el protector y el ensamblado del hendidor . Reponga siempre el protector y el ensambiado del hendidor una vez completadas las opera - ciones de corte que no sean de paso . Ver figura 2B . 53
Page: 54

CONSTRUYENDO UNA VARA DE EMPUJE Durante el corte a Io largo de materiales con menos de 4 pulgadas de ancho , se debe hacer uso de una vara de empuje para com - pletar la alimentaci6n . Puede construirse f _ cilmente utilizando material descartado y siguiendo el patr6n ilustrado en la Figura 2C Fig . 2C La vara de empuje debe estar hecha con madera de 3 / 4 6 1 / 2 pulgada o con un grosor inferior al ancho del material a cortarse . La figura 2C debe copiarse y hacerse a escala , de tal manera que las rejillas sean de 1 / 2 pulgada cuadrada . Esta copia puede emplearse en la construcci6n de su vara de empuje . 54
Page: 55

DESEMPACANDO Y Fig . 3 - 1 REVISANDO EL CONTENIDO La sierra de mesa es una maquina pesada . Se requieren dos personas para desempaquetarla y levantar la sierra de mesa . Esta sierra de mesa requerira cierta cantidad de ensamblado . Esta sierra de mesa y su gufa se envfan en una sola caja . Esta caja tambien incluye una caja de piezas para la sierra . 1 . Remueva las piezas de todas las cajas y col6quelas sobre una superficie de trabajo limpia . 2 . Se requieren dos o mas personas para levantar la sierra de mesa de la paleta de embarque . 3 . Remueva cualquier material y revestimiento protectivo de todas las piezas y de la sierra de mesa . El revestimiento de las piezas puede quitarse con rociar WD - 40 sobre elias y limpiandolas con un patio suave . Podra ser nece - \ sario repetir este proceso varias veces antes de poder quitar todo el revestimiento protectivo . \ \ PRECAUCION : NO utilice acetona , gasolina ni diluyente de \ laca para quitar ningun revestimiento protectivo de su sierra de mesa . 4 . Tras la limpieza , aplique una cera en pasta de buena 12 calidad sobre cualquier superficie sin pintar . Asegt ] rese de pulir la cera antes del montaje . 5 . Compare los artfculos con las figuras que aparecen abajo . Verifique que todos los artfculos esten presentes antes de desechar la caja de envfo . Si faltan piezas , Ilame a la Lfnea de Ayuda al Cliente al 1 - 800 - 897 - 7709 . El ala de extensi6n derecha debe estar plenamente ensam - blado y la cubierta del motor debe estar cerrada y afianzada antes de que se conecte la sierra de mesa a la fuente de 11 energfa . Si Ilegara a faltar cualquier pieza , no intente enchufar el cord6n de potencia y encender la sierra de mesa . La sierra de mesa s61o podra encenderse despues de que se hayan obtenido todas las piezas y estas hayan sido instaladas correctamente . SIERRA DE MESA 10 1 . Ensamblado de sierra de mesa \ \ 2 . Ala de extensi6n , hierro estampado ( 2 ) \ \ \ \ \ \ \ 3 . Volante de mane ( 2 ) \ \ \ \ \ \ 4 . Perilla de cierre del volante de mane ( 2 ) \ \ \ \ 5 . Vara de montaje del hendidor \ \ \ 6 . Ensamblado del soporte del hendidor \ \ \ 7 . Gancho para Ilaves \ 8 . Gancho de la gufa ( 2 ) 9 . Correa Poly - V 10 . Ensamblado del protector de hojas y del hendidor 11 . Ensamblado de patas ( 2 ) 12 . Tirante de tracci6n ( 2 ) 13 . Interruptor 14 . Hoja de la sierra ( no ilustrada ) 9 5 4 55
Page: 56

Fig . 3 = 2 20 21 22 23 24 28 GUiA 20 . Ensamblado de la gufa de corte a 1olargo 25 . Conector al riel posterior de la gufa 21 . Riel delantero de la gufa , derecho 26 . Tapa de extremo del riel delantero , derecho 22 . Riel delantero de la gufa , izquierdo 27 . Tapa de extremo del riel delantero , izquierdo 23 . Riel trasero de la gufa , derecho 28 . Barra de alineaci6n del riel delantero de la gu / a ( 2 ) 24 . Riel trasero de la gufa , izquierdo Fig . 3 = 3 40 ESCUADRA DE INGLETES 40 . Escuadra de ingletes 56
Page: 57

Los estuches de ferreteria no est _ n identificados ni etiquetados . Consulte el diagrama de ferreteria para ayudar a Iocalizar la pieza correcta . Ver figura 3 - 4 . Fig . 3 = 4 © B TUERCAHEXM8x 1.25 TORNILLODECABEZAHEXM8x 1.25x 25mm © B © TORNILLODE CABEZAHE × M8x 1.25 x 30 mm TUERCAHEX5 / 16pulg . - 18 PERNO DE CARROCERiA5 / 16 - 18 x 5 / 8 pulg . TUERCACUADRADAM6 TORNILLODE CABEZACUADRADAM8x 1.25 x 35 mm © l © ARANDELAPLANAM8 TORNILLODE CABEZAHUECAHE × M8x 1.25 x 25 mm © B TORNILLODE CABEZAHUECAHE × M8x 1.25 x 35 mm ARANDELAPLANA5 / 16pulg . TORNILLODE CABEZAHE × M6x 12 mm ARANDELADECIERREM8 TORNILLOAUTOROSCADORDECABEZAREDONDA M4x8 mm TORNILLOAUTOROSCADORDECABEZAREDONDA ARANDELADECIERRE5 / 16pulg . M4x16 mm Estuehe de Ferreteria para Alas de Extensi6n Estuche de Ferreteria para Patas de Gabinete ( OR92013 ) Incluye : ( OR92020 ) Incluye : Arandela Plana M8 ( 8 ) Arandela Plana M8 ( 16 ) Arandela de Cierre M8 ( 8 ) Arandela Plana 5 / 16 pulg . ( 8 ) Tornillo de Cabeza Hexagonal M8 x 1.25 x 30 mm ( 8 ) Arandela de Cierre M8 ( 8 ) Arandela de Cierre 5 / 16 pulg . ( 8 ) Estuche de Ferreteria para Riel Posterior ( OR92016 ) Tomillo de Cabeza Hexagonal M8 x 1.25 x 25 mm ( 8 ) Incluye : Pemo de Carroceria 5 / 16 - 18 x 5 / 8 pulg . ( 8 ) Arandela Plana M8 ( 8 ) Tuerca Hexagonal M8 ( 8 ) Arandela de Cierre ( 6 ) Tuerca Hexagonal 5 / 16 pulg . ( 8 ) Tornillo de Cabeza de Bot6n M8 x 1.25 x 25 mm ( 4 ) Tornillo de Cabeza de Bot6n M8 x 1.25 x 35 mm ( 2 ) Ferreteria para Interruptor ON / OFF ( encendido apagado ) ( Ferreteria aeabado en Oxido Negro ) : Tuerca Hexagonal M8 ( 2 ) Tomillo de Cabeza Hexagonal M6 x 12 mm ( 2 ) Eetuche de Ferreteria para Riel Delantero ( OR92017 ) Tuerca Cuadrada M6 ( 2 ) Incluye : Ferreteria Varia : Arandela Plana M8 ( 4 ) Arandela de Cierre M8 ( 4 ) Tornillo de Chapa Met & lica M4 x 8 mm ( 6 ) Tornillo de Cabeza Cuadrada M8 x 1.25 x 35 mm ( 4 ) Tornillo de Chapa Metalica M4 x 16 mm ( 4 ) Tuerca Hex M8 ( 4 ) 57
Page: 58

2 4 5 6 7 8 24 25 3 _ . 10 11 12 23 13 15 22 16 17 18 21 2O 19 1 . Ensamblado del hendidor 14 . Escala de biselado 2 . Protector de hoja 15 . Volante de mano de elevaci6n de hoja 16 . Perilla de cierre del volante de mano 3 . Dedos anticontragolpe 17 . Gabinete de 3 / 4 4 . Hoja 5 . Pieza de inserci6n para alinear cortes 18 . Pata del gabinete 19 . Pie de caucho 6 . Reten de la gufa trasera 7 . Superficie de la mesa 20 . Gancho de la gufa 8 . Gufa de corte a Io largo 21 . Interruptor de arranque / parada 9 . Riel trasero 22 . Volante de mano de biselado 23 . Perilla de cierre del volante de mano de biselado 10 . Ala de acero estampado de 10 pulg . 11 . Riel delantero con escala 24 . Escuadra de ingletes 12 . Agarradera de cierre de la gufa de corte a Io largo 25 . Ranura de la escuadra de ingletes 13 . Cubierta del motor 58
Page: 59

arandela de cierre M8 y tuerca hexagonal M8 sobre cada HERRAMIENTAS REQUERIDAS uno de los ocho tornillos que conectan el ensamblado de Se requieren las siguientes herramientas para el montaje y el patas al gabinete . No apriete la ferreteria del todo en alineamiento . Aviso : Se suministran dos Ilaves de hoja y cinco este memento . Ver la figura 4 - 1 . Ilaves hexagonales con su sierra de mesa . Las herramientas restantes son herramientas tfpicas de taller y no se incluyen 3 , Conecte dos tirantes de tracci6n ( F ) por dentro y entre con su sierra de mesa . las patas delanteras y traseras ya conectadas al gabinete con ( G ) echo pernos de carrocerfa 5 / 16 - 18 x 5 / 8 pulg . , Llave de 18 mm Llave de 8 mm arandelas planas de 5 / 16 pulg . , arandelas de cierre de Llave de 13 mm Llave hexagonal de 3 / 16 pulg . 5 / 16 pulg . y tuercas hexagonales 5 / 16 - 18 y afiance toda Llave de 10 mm Destornillador Phillips # 2 la ferreteria de manera segura . Ver la figura 4 - 1 . MONTAJE DE LA CORREA POLY = V • La sierra de mesa es una maquina pesada . Podran requerirse dos personas para ciertas operaciones de montaje . • NO monte la sierra de mesa hasta que este seguro que ASEGURESE de que la sierra de mesa este desconectada la herramienta este desenchufada . de la fuente de energfa . • NO monte la sierra de mesa hasta que este seguro que el interrupter de energfa est _ en la posici6n de " apagado " Figura 5 = 1 ( OFF ) . • Para su seguridad personal , NO conecte la maquina a la fuente de energia hasta que la m _ quina se encuentre / completamente montada y haya lefdo y entendido este Manual del Operario cabalmente . A MONTAJE DE LAS PATAS DEL GABINETE ASEGURESE de que la sierra de mesa este desconectada de la fuente de energfa . Coloque la mesa boca abajo para que descanse sobre la mesa de hierro fundido . PRECAUClON : La sierra de mesa es pesada ; se requieren dos personas para esta operaci6n . Este seguro de colocar cart6n sobre el suelo para proteger la superficie de la mesa . 2 , Conecte los ensamblados de pata ( A ) al frente ( B ) y parte posterior ( C ) del gabinete de la sierra de mesa colocando ( D ) echo tornillos de cabeza hexagonal M8 x 25 mm y echo arandelas planas M8 hacia abajo a traves de los agujeros de montaje en el ensamblado de patas y el gabinete ( E ) . Coloque una arandela plana M8 , Figura 44 1 , A Aseg0rese de que todo el material de embalaje haya sido removido del interior del gabinete . G E 2 . Abra la cubierta del motor y coloque la correa Poly - V ( A ) o " li del motor sobre la polea de la hoja ( B ) . Ver la figura 5.1 3 . Levante el motor ( C ) cuidadosamente y coloque la correa debajo de la polea del motor ( no ilustrada ) . Aseg0rese de que las muescas en " V " en la correa coincidan con las muescas en " V " de la polea de la hoja y el motor . Ver figura 5 - 1 . 4 . Baje el motor cuidadosamente y cierre la cubierta del motor . g 59
Page: 60

MONTAJE DE LAS ALAS DE EXTENSION MONTAJE DEL VOLANTE DE MANO ASEGORESE de que la sierra de mesa este desconectada ASEGURESE de que la sierra de mesa este desconectada de la fuente de energfa . de la fuente de energia . Figura 7 - 1 El ala de extensi6n derecho debe estar plenamente ensam - blado y la cubierta del motor debe estar cerrada y afianzada antes de que se conecte la sierra de mesa a la fuente de energfa . Figura 64 A J o B B 1 , Coloque uno de los volantes de mano ( A ) sobre el eje de biselado ( B ) Iocalizado en el lade del gabinete . La ranura ( C ) en el dorso del volante debe alinearse con el pasador PRECAUC [ ON : Las alas de extensi6n son pesadas . Se ( D ) . Ver la figura 7 - 1 . requieren dos personas para ensamblar ambas alas de extensi6n a la sierra de mesa . 2 , Figura 7 - 2 Monte una de las alas de extensi6n ( A ) al lado izquierdo de la sierra de mesa . Los cuatro agujeros ( B ) en el ala de extensi6n deben ser alineados con los cuatro agu - jeros en el lade izquierdo de la sierra de mesa . Utilice cuatro tornillos de cabeza hexagonal M8 x 30 mm , aran - E delas de cierre M8 y arandelas planas M8 . No apriete el herramental completamente en este momento . Ver la \ figura 6 - 1 . Figura 6 - 2 2 . Enrosque la perilla de cierre ( E ) sobre el extremo roscado del eje ( F ) . Ver la figura 7 - 2 . 3 . Repita los pasos anteriores para montar el volante restante y la perilla de cierre sobre el eje de elevaci6n y bajada de la hoja , Iocalizado al frente del gabinete . 3 . Coloque una regla ( C ) a Io ancho de la mesa de la sierra ( D ) y el ala de extensi6n ( E ) . Asegurese de que la cara frontal del ala de extensi6n ( F ) este plana con el frente de la mesa de la sierra ( G ) . Ajuste el ala de extensi6n de tal manera que se encuentre perfectamente plana con la mesa de la sierra . Apriete la ferreteffa de manera segura . Ver la figura 6 - 2 . 4 . Repita los pasos 2 y 3 arriba para montar la otra exten - si6n al lade derecho de la sierra . 60
Search in Table Saw on ebay
"