Home | Register Login | Wanted Manuals | MarketPlace | Members Area | Manuals Manufacturer Directory | UPC Lookup | Information Pages | Policy


Back To Craftsman Miter Saw       Model: 315.212040 or 315212040 Craftsman 10 Inch Compound Miter Saw
Regular Text Search or Search by Model Number

Register / log-in to add to your Hammerwall Collection.
Manual Location


This is a partial text extraction from the pdf, to download the pdf, click the Manual tab. If you want to search this text, hold control and F, and type the word you are looking for.

Page: 1

Operator's Manual II : RRFrSMRN I 10 in . COMPOUND MITER SAW Double Insulated Model No . 315.212040 o O _ , WARNING : To reduce the risk of injury , the user must read and under - stand the operator's manual before using this product . Customer Help Line : 1 - 800 - 932 - 3188 Sears , Roebuck and Co . , Hoffman Estates , IL 60179 USA Visit the Craftsman web page : www . sears . com / craftsman 0Q0s 983000 - 471 Save this manual for future reference 2 - 04
Page: 2

• Warranty and Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 • General Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 4 • Specific Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 5 • Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 7 • Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 • Glossary of Terms for Woodworking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 • Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 12 • Unpacking and Tools Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 • Loose Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 • Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 - 21 • Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 - 28 • Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 - 30 • Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 • Exploded View and Repair Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 - 39 • Parts Ordering / Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 FULL ONE YEAR WARRANTY If this product fails due to a defect in material or workmanship within one year from the date of purchase , Sears will repair it free of charge . Contact a Sears Service Center for repair . If this product is used for commercial or rental purposes , this warranty applies only for 90 days from the date of pur - chase . This warranty gives you specific legal rights , and you may also have other rights which vary from state to state . Sears , Roebuck and Co . , Dept . 817WA , Hoffrnan Estates , IL 60179 Your saw has many features for making cutting operations more pleasant and enjoyable . Safety , performance and de - pendability have been given top priority in the design of this saw making it easy to maintain and operate .
Page: 3

• ALWAYS WEAR SAFETY GLASSES WITH SIDE _ WARNING : Read and understand all instruc - tions . Failure to follow all instructions listed below , SHIELDS . Everyday eyeglasses have only impact - may result in electric shock , fire and / or serious resistant lenses , they are NOT safety glasses . personal injury . • SECURE WORK . Use clamps or a vise to hold work when practical . It's safer than using your hand and READ ALL INSTRUCTIONS frees both hands to operate tool . • KNOW YOUR POWER TOOL . Read the operator's • DON'T OVERREACH . Keep proper footing and bal - manual carefully . Learn the saw's applications and limi - ance at all times . tations as well as the specific potential hazards related to this tool . • MAINTAIN TOOLS WITH CARE . Keep tools sharp and clean for better and safer performance . Follow instruc - • GUARD AGAINST ELECTRICAL SHOCK BY PRE - tions for lubricating and changing accessories . VENTING BODY CONTACT WITH GROUNDED SURFACES . For example , pipes , radiators , ranges , • DISCONNECT TOOLS . When not in use , before ser - refrigerator enclosures . vicing , or when changing attachments , blades , bits , cutters , etc . , all tools should be disconnected . • KEEP GUARDS IN PLACE and in good working • AVOID ACCIDENTAL STARTING . Be sure switch is off order . Never operate the tool with any guard or cover removed . Make sure all guards are operating properly when plugging in any tool . before each use . • USE RECOMMENDED ACCESSORIES , The use of • REMOVE ADJUSTING KEYS AND WRENCHES . improper accessories may risk injury . Form habit of checking to see that keys and adjusting • NEVER STAND ON TOOL . Serious injury could occur wrenches are removed from tool before turning it on . if the tool is tipped or if the cutting tool is unintention - • KEEP WORK AREA CLEAN . Cluttered areas and ally contacted . benches invite accidents . DO NOT leave tools or • CHECK DAMAGED PARTS . Before further use of pieces of wood on the saw while it is in operation . the tool , a guard or other part that is damaged should • AVOID DANGEROUS ENVIRONMENTS . Don't use be carefully checked to determine that it will operate power tools in damp or wet locations or expose to rain . properly and perform its intended function . Check for Keep the work area well lit . alignment of moving parts , binding of moving parts , breakage of parts , mounting and any other conditions • KEEP CHILDREN AND VISITORS AWAY . All visitors that may affect its operation . A guard or other part that should wear safety glasses and be kept a safe dis - is damaged must be properly repaired or replaced by tance from work area . Do not let visitors contact tool or an authorized service center to avoid risk of personal extension cord while operating . injury . • MAKE WORKSHOP CHILDPROOF with padlocks and • USE THE RIGHT DIRECTION OF FEED . Feed work master switches , or by removing starter keys . into a blade or cutter against the direction of rotation of • DON'T FORCE TOOL . It will do the job better and blade or cutter only . safer at the feed rate for which it was designed . • NEVER LEAVE TOOL RUNNING UNATTENDED . • USE RIGHT TOOL . Don't force the tool or attachment TURN THE POWER OFF . Don't leave tool until it to do a job it was not designed for . Don't use it for a comes to a complete stop . purpose not intended . • PROTECT YOUR LUNGS . Wear a face or dust mask if • MAKE SURE YOUR EXTENSION CORD IS IN GOOD the cutting operation is dusty . CONDITION . When using an extension cord , be sure • PROTECT YOUR HEARING . Wear hearing protection to use one heavy enough to carry the current your during extended periods of operation . product will draw . An undersized cord will cause a drop • DON'T ABUSE CORD . Never yank cord to disconnect in line voltage resulting in loss of power and overheat - from receptacle . Keep cord from heat , oil , and sharp ing . A wire gage size ( A . W . G . ) of at least 14 is recom - mended for an extension cord 25 feet or less in length . edges . If in doubt , use the next heavier gage . The smaller the • USE OUTDOOR EXTENSION CORDS . When tool is gage number , the heavier the cord . used outdoors , use only extension cords with ap - proved ground connection that are intended for use • DRESS PROPERLY . Do not wear loose clothing , outdoors and so marked . gloves , neckties , or jewelry . They can get caught and draw you into moving parts . Rubber gloves and • KEEP BLADES CLEAN , SHARP , AND WITH nonskid footwear are recommended when working SUFFICIENT SET . Sharp blades minimize stalling and outdoors . Also wear protective hair covering to contain kickback . long hair . • BLADE COASTS AFTER BEING TURNED OFF .
Page: 4

• NEVER USE IN AN EXPLOSIVE ATMOSPHERE . • NEVER TOUCH BLADE or other moving parts during use . Normal sparking of the motor could ignite fumes . • NEVER START A TOOL WHEN ANY ROTATING COM - • INSPECT TOOL CORDS PERIODICALLY . If damaged , PONENT IS IN CONTACT WITH THE WORKPIECE . have repaired by a qualified service technician at an authorized service facility . The conductor with insula - • DO NOT OPERATE A TOOL WHILE UNDER THE tion having an outer surface that is green with or with - INFLUENCE OF DRUGS , ALCOHOL , OR ANY out yellow stripes is the equipment - grounding conduc - MEDICATION . tor . If repair or replacement of the electric cord or plug • POLARIZED PLUGS . To reduce the risk of electric is necessary , do not connect the equipment - grounding shock , this tool has a polarized plug ( one Made is conductor to a live terminal . Repair or replace a dam - wider than the other ) . This plug will fit in a polarized aged or worn cord immediately . Stay constantly aware outlet only one way . If the plug does not fit fully in the of cord location and keep it well away from the rotating outlet , reverse the plug . If it still does not fit , contact a blade . qualified electrician to install the proper outlet . Do not • INSPECT EXTENSION CORDS PERIODICALLY and change the plug in any way . replace if damaged . • WHEN SERVICING use only identical replacement • KEEP TOOL DRY , CLEAN , AND FREE FROM OIL parts . Use of any other parts may create a hazard or AND GREASE . Always use a clean cloth when clean - cause product damage . ing . Never use brake fluids , gasoline , petroleum - based • CHECK WITH A QUALIFIED ELECTRICIAN or service products , or any solvents to clean tool . personnel if the grounding instructions are not com - • STAY ALERT AND EXERCISE CONTROL . Watch pletely understood or if in doubt as to whether the tool what you are doing and use common sense . Do not is properly grounded . operate too ] when you are tired . Do not rush . • USE ONLY RECOMMENDED ACCESSORIES listed • DO NOT USE TOOL IF SWITCH DOES NOT TURN IT in this manual or addendums . Use of accessories ON AND OFF . Have defective switches replaced by an that are not listed may cause the risk of personal authorized service center . injury . Instructions for safe use of accessories are included with the accessory . • USE ONLY CORRECT BLADES . Do not use blades with incorrect size holes . Never use blade washers or • DOUBLE CHECK ALL SETUPS . Make sure blade is blade bolts that are defective or incorrect . The maxi - tight and not making contact with saw or workpiece mum blade capacity of your saw is 10 in . ( 254 mm ) . before connecting to power supply . • BEFORE MAKING A CUT , BE SURE ALL ADJUST - • MAKE SURE THE WORK AREA HAS AMPLE LIGHT - MENTS ARE SECURE . ING to see the work and that no obstructions will in - terfere with safe operation BEFORE performing any • AVOID CUTTING NAILS . Inspect for and remove all work using the table saw . nails from lumber before cutting . • BE SURE THE BLADE CLEARS THE WORKPIECE . • FIRMLY CLAMP OR BOLT your miter saw to a work - bench or table at approximately hip height . Never start the saw with the blade touching the workpiece . Allow motor to come up to full speed • DO NOT REMOVE THE SAW'S BLADE before starting cut . GUARDS , Never operate the saw with any guard or • MAKE SURE THE MITER TABLE AND SAW ARM cover removed . Make sure all guards are operating properly before each use . ( BEVEL FUNCTION ) ARE LOCKED IN POSITION BEFORE OPERATING YOUR SAW . Lock the miter • KEEP HANDS AWAY FROM CUTTING AREA . Do not table by securely tightening the miter lock handle . Lock reach underneath work or in blade cutting path with the saw arm ( bevel function ) by securely tightening the your hands and fingers for any reason . Always turn the bevel lock knob . power off . • NEVER USE A LENGTH STOP ON THE FREE SCRAP • ALWAYS SUPPORT LONG WORKPIECES while cut - END OF A CLAMPED WORKPIECE . NEVER hold ting to minimize risk of blade pinching and kickback . onto or bind the free scrap end of the workpiece in any Saw may slip , walk or slide while cutting long or heavy operation . If a work clamp and length stop are used boards . together , they must both be installed on the same side • ALWAYS USE A CLAMP to secure the workpiece of the saw table to prevent the saw from catching the when possible . loose end and kicking up .
Page: 5

• NEVERcutmorethanonepieceat atime . DONOT occur , stand clear and allow the saw blade to come to STACKmorethanoneworkpieceonthesawtableat a a complete stop . Disconnect your saw from the power time . supply and securely retighten the blade bolt . • NEVERPERFORMANYOPERATIOFNREEHAND , • IF ANY PART OF THIS MITER SAW IS MISSING or Alwaysplacetheworkpieceto becutonthemiter should break , bend , or fail in any way , or should any tableandpositionitfirmlyagainstthefenceasaback - electrical component fail to perform properly , shut off stop . Alwaysusethefence . the power switch , remove the miter saw plug from the power source and have damaged , missing , or failed • NEVERhandholdaworkpiecethatistoosmallto be parts replaced before resuming operation . clampedK . eephandsclearof thenohandszone . • ALWAYS STAY ALERT ! Do not allow familiarity ( gained • NEVERreachbehindu , ndero , arwithinthreeinchesnd from frequent use of your saw ) to cause a careless of thebladeanditscuttingpathwithyourhands mistake . ALWAYS REMEMBER that a careless fraction fingersforanyreason . of a second is sufficient to inflict severe injury . • NEVERreachto pickupaworkpiecea , pieceof scrap , • MAKE SURE THE WORK AREA HAS AMPLE LIGHT - oranythingelsethatisinornearthecuttingpathofthe ING to see the work and that no obstructions will inter - blade . fere with safe operation BEFORE performing any work • AVOIDAWKWARDOPERATIONASNDHANDPO - using your saw . SITIONSwhereasuddenslipcouldcauseyourhandvee • ALWAYS TURN OFF THE SAW before disconnecting to moveintotheblade . ALWAYSmakesureyouhath it to avoid accidental starting when reconnecting to goodbalanceN . EVERoperateyourmitersawon power supply . NEVER leave the saw unattended while floororinacrouchedposition . connected to a power source . • NEVERstandorhaveanypartof yourbodyinlinewith • NEVER lift this tool by gripping the sliding miter fence . thepathofthesawblade . • SAVE THESE INSTRUCTIONS . Refer to them • ALWAYSreleasethepowerswitchandallowtheofthe frequently and use to instruct other users . If you loan sawbladeto stoprotatingbeforeraisingit out someone this tool , loan them these instructions also . workpiece . • DO NOT TURN THE MOTOR SWITCH ON AND OFF RAPIDLY . This could cause the saw blade to loosen and could create a hazard . Should this ever _ WARNING " Some dust created by power sanding , sawing , grinding , drilling , and other construction activities con - tains chemicals known to cause cancer , birth defects or other reproductive harm . Some examples of these chem - icals are : • lead from lead - based paints , • crystalline silica from bricks and cement and other masonry products , and • arsenic and chromium from chemically - treated lumber . Your risk from these exposures varies , depending on how often you do this type of work . To reduce your exposure to these chemicals : work in a well ventilated area , and work with approved safety equipment , such as those dust masks that are specially designed to filter out microscopic particles .
Page: 6

Someof thefollowingsymbolsmaybeusedonthistool . PleasestudythemandlearntheirmeaningP . roper interpretatioonfthesesymbolswillallowyouto operatethetoolbetterandsafer . SYMBOL NAME DESIGNATION / EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequenc ( ycyclespersecond ) W Watt Power min Minutes Time " % , Alternating Current Type of current Direct Current Type or a characteristic of current no No Load Speed Rotational speed , at no load [ ] Class II Construction Double - insulated construction . . . / min Per Minute Revolutions , strokes , surface speed , orbits etc . , per minute Wet Conditions Alert Do not expose to rain or use in damp locations . Read The Operator's Manual Tooperreadtourc'se tmheanruisakl obfeifnojruery , usuinsegr thmisuspt roredaudct . and understand Protection Eye O Always wear safety goggles or safety glasses with dsideuct . shields and a full face shield when operating this pro Safety safety . your , _ Alert Precautions that involve No Hands Symbol serious personal injury . Failure to keep your hands away from the blade will result in Symbol No Hands Failure to keep your hands away from the blade will result in serious personal injury . No Hands Symbol Failure to keep your hands away from the blade will result in serious personal injury . No Hands Symbol Failure to keep your hands away from the blade will result in serious personal injury . Hot Surface To reduce the risk of injury or damage , avoid contact with ® any hot surface .
Page: 7

The following signal words and meanings are intended to explain the levels of risk associated with this product . SYMBOL SIGNAL MEANING Indicates an imminently hazardous situation , which , if not avoided , will , _ DANGER : result in death or serious injury . Indicates a potentially hazardous situation , which , if not avoided , could , _ WARNING : result in death or serious injury . Indicates a potentially hazardous situation , which , if not avoided , may CAUTION : result in minor or moderate injury . CAUTION : ( Without Safety Alert Symbol ) Indicates a situation that may result in property damage . SERVICE , _ WARNING : To avoid serious personal injury , do not attempt to use this product until you read Servicing requires extreme care and knowledge and should be thoroughly and understand completely the performed only by a qualified service technician . For service operator's manual . Save this operator's manual we suggest you return the product to your nearest AUTHO - and review frequently for continuing safe opera RIZED SERVICE CENTER for repair . When servicing , use tion and instructing others who may use this only identical replacement parts . product . , _ ls WARNING : The operation of any power tool can result in foreign objects being thrown into your eyes , which can result in severe eye damage . Before beginning power tool operation , always wear safety goggles or safety glasses with side shields and a full face shield when needed . We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields . Always use eye protection which is marked to comply with ANSI Z87 . 1 . SAVE THESE INSTRUCTIONS
Page: 8

DOUBLE INSULATION EXTENSION CORDS Double insulation is a concept insafety in electric power tools , When using a power tool at a considerable distance from which eliminates the need for the usual three - wire grounded a power source , be sure to use an extension cord that has power cord . All exposed metal parts are isolated from the the capacity to handle the current the tool will draw . An internal metal motor components with protecting insulation . undersized cord will cause a drop in line voltage , resulting Double insulated tools do not need to be grounded . in overheating and loss of power . Use the chart to deter - mine the minimum wire size required in an extension cord . Only round jacketed cords listed by Underwriter's Labora - _ WARNING : The double insulated system is tories ( UL ) should be used . intended to protect the user from shock resulting from a break in the tool's internal insulation . Observe When working outdoors with a tool , use an extension all normal safety precautions to avoid electrical cord that is designed for outside use . This type of cord is shock . designated with " WA " on the cord's jacket . Servicing of a tool with double insulation requires extreme Before using any extension cord , inspect it for loose or care and knowledge of the system and should be performed exposed wires and cut or worn insulation . only by a qualified service technician . For service , we sug - * * Ampere rating ( onteelfaceplate ) 0 - 2.0 2.1 - 3.4 3.5 - 5.0 5.1 - 7.0 7.1 - 12.0 12.1 - 16.0 gest you return the tool to your nearest authorized service center for repair . Always use original factory replacement Cord Length Wire Size ( A . W . G , ) parts when servicing . 25 ' 16 16 16 16 14 14 ELECTRICAL CONNECTION 50 ' 16 16 16 14 14 12 This tool has a precision - built electric motor . It should be 100 ' 16 16 14 12 10 - - connected to a power supply that is 120 volts , 60 Hz , AO * * Used on12gage - 20ampcircuit . only ( normal household current ) . Do not operate this tool NOTE : AWG = American Wire Gauge on direct current ( DC ) . A substantial voltage drop will cause a loss of power and the motor will overheat . If your tool does _ WARNING : Keep the extension cord clear of the not operate when plugged into an outlet , double - check the working area . Position the cord so that it will not power supply . become entangled in the rotating foam pad or caught on lumber , tools or other obstructions while you are working with a power tool . Failure to do so can result in serious personal injury . WARNING : Check extension cords before each A use . If damaged replace immediately . Never use tool with a damaged cord since touching the dam - aged area could cause electrical shock resulting in serious injury .
Page: 9

Arbor Set Theshaftonwhicha bladeorcuttingtoolismounted . The distance that the tip of the sawblade tooth is bent ( or set ) outward from the face of the blade . BevelCut Throw - Back A cuttingoperationmadewiththebladeat anyangle otherthan90 ° to themitertable . Throwing of a workpiece in a manner similar to a kick - back . Usually associated with a cause other than the kerf Crosscut closing , such as a workpiece not being against the fence , A cutting or shaping operation made across the grain of being dropped into the blade , or being placed inadver - the workpiece . tently in contact with the blade . Compound Miter Cut Through Sawing A compound miter cut is a cut made using a miter angle Any cutting operation where the blade extends completely and a bevel angle at the same time . through the thickness of the workpiece . Freehand Workpiece Performing a cut without using a fence , miter gage , The item on which the cutting operation is being done . fixture , work clamp , or other proper device to keep the The surfaces of a workpiece are commonly referred to as workpiece from twisting or moving during the cut . faces , ends , and edges . Gum Zero Clearance Throat Plate A sticky , sap based residue from wood products . A plastic throat plate inserted in the miter table that al - Miter Cut lows for blade clearance . When you make your first cut A cutting operation made with the blade at any angle with your compound miter saw , the saw blade cuts a other than 90 ° to the fence . slot through the throat plate the exact width of the blade . Resin This provides for a zero clearance kerf that minimizes A sticky , sap base substance that has hardened . workpiece tear - out . No Hands Zone Revolutions Per Minute ( RPM ) The area between the marked lines on the left and right The number of turns completed by a spinning object in one minute . side of the miter table base . This zone is identified by no hands zone labels placed inside the marked lines on the Saw Blade Path miter table base . The area over , under , behind , or in front of the blade . As it applies to the workpiece , that area which will be , or has been , cut by the blade .
Page: 10

Product Specifications : When the miter angle ( miter table ) is set at 0 ° and the bevel angle is set at 0 ° : Blade Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . 10 in . Maximum nominal lumber sizes : 4 x 4 , 2 x 6 Blade Arbor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 / 8 in . When the miter angle ( miter table ) is set at 45 and the bevel No Load Speed . . . . . . . . . . . . . . . . . . . . . . . 5500 / min . angle is set at 0 ° : Input . . . . . . . 120 Volts , 60 Hz - AC Only , 14 Amperes Maximum nominal lumber sizes : 2 x 4 Net Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Ibs . When the miter angle ( miter table ) is set at 0 ° and the bevel angle is set at 45 : Maximum nominal lumber sizes : 2 x 6 When the miter angle ( miter table ) is set at 45 " and the bevel angle is set at 45 ° : Maximum nominal lumber sizes : 2 x 4 UPPER BLADE GUARD SAW ARM DUST GUIDE SWITCH TRIGGER LOWER BLADEGUARD BEVEL LOCKKNOB MITERTABLE BEVEL SCALE " NO HANDS ZONE " LABEL " NO HANDSZONE " BOUNDARYLINE FENCE MITER SCALE ZERO CLEARANCE THROATPLATE MITER LOCKPLATE WORKCLAMP MITER CONTROL BASE LOCKHANDLE POSITIVESTOP ( S ) ARM Fig . 1 10
Page: 11

KNOW YOUR COMPOUND MITER SAW SPINDLE LOCK BUTTON See Figure 1 . See Figure 3 . Before attempting to use this product , familiarize your - A spindle lock button has been provided for locking the self with all operating features and safety requirements . spindle which keeps the blade in your saw from rotating . Depress and hold the lock button while installing , changing , 14 AMP MOTOR or removing blade . Your saw has a powerful 14 amp motor with sufficient power to handle tough cutting jobs . It is made with all SPINDLE ball bearings , and has externally accessible brushes for LOCKBUTTON ease of servicing . 10 in . BLADE A 10 in . saw blade is included with your compound miter saw . It will cut materials up to 2 in . thick or 6 in . wide , depending upon the angle at which the cut is be - ing made . CARRYING HANDLE See Figure 2 . SWITCH For convenience when carrying or transporting your TRIGGER miter saw from one place to another , a carrying handle has been provided on top of the saw arm as shown in figure 2 . To transport , turn off and unplug your saw , then LOCK lower the saw arm and lock it in the down position . Lock PIN saw arm by depressing the lock pin . CARRYING o HANDLE Fig . 3 TRIGGER LOCK See Figure 4 . SAW To prevent unauthorized use of your compound miter saw , ARM we suggest that you disconnect it from the power supply and lock the switch in the off position . To lock the switch , install a padlock ( not included ) through the hole in the switch trigger . A lock with a long shackle up to 17 / 64 in . diameter may be used . When the lock is installed and locked , the switch is inoperable . Store the padlock key in another loca - tion . SWITCH TRIGGER MITERLOCK HANDLE PADLOCK SAWARM LOCKEDIN DOWNPOSITION Fig . 2 MITER LOCK HANDLE See Figure 2 . The miter lock handle securely locks your saw at de - sired miter angles . Fig . 4 11
Page: 12

POSITIVE STOPS ON MITER TABLE Tighten all four bolts securely . Positive stops have been provided at 0,15,22 - 1 / 2 , The hole pattern for mounting to a workbench is shown in 30 , and 45 ° . The 0,15,22 - 1 / 2,30 ° , and 45 positive figure 5 . Carefully check the workbench after mounting to stops have been provided on both the left and right side make sure that no movement can occur during use . If any of the miter table . tipping , sliding , or walking is noted , secure the workbench to the floor before operating . BEVEL LOCK KNOB The bevel lock knob securely locks your compound , _ WARNING : Always make sure your compound miter saw at desired bevel angles . A positive stop ad - miter saw is securely mounted to a workbench or an justment screw has been provided on each side of the approved workstand . Failure to do so could result in an saw arm . These adjustment screws are for making fine accident resulting in possible serious personal injury . adjustments at 0 and 45 . ELECTRIC BRAKE ELECTRICAL CONNECTION An electric brake has been provided to quickly stop Your saw has a precision built electric motor . It should be blade rotation after the switch is released . connected to a power supply that is 120 volts , 60 Hz , AC only ( normal household current ) . Do not operate this tool FENCE on direct current ( DC ) . A substantial voltage drop will cause The fence on your compound miter saw has been a loss of power and the motor will overheat . If your tool does provided as a support to hold your workpiece securely not operate when plugged into an outlet , double - check the against when making all cuts . power supply . SELF - RETRACTING LOWER BLADE WARNING : The operation of any saw can result in A GUARD foreign objects being thrown into your eyes , which can The lower blade guard is made of shock - resistant , see - result in severe eye damage . Before starting power through plastic that provides protection from each side tool operation , always wear safety goggles or safety of the blade . It retracts over the upper blade guard as glasses with side shields and a full face shield when the saw is lowered into the workpiece . needed . We recommend wide vision safety mask for use over eyeglasses or standard safety glasses with MOUNTING HOLES side shields . See Figure 5 . Your compound miter saw should be permanently WARNING : Do not attempt to modify this tool orth A mounted to a firm supporting surface such as a work - create accessories not recommended for use wi bench . Four bolt holes have been provided in the saw this tool . Any such alteration or modification is misuse base for this purpose . Each of the four mounting holes and could result in a hazardous condition leading to possible serious personal injury . should be bolted securely using 3 / 8 in . machine bolts , lock washers , and hex nuts ( not included ) . Bolts should be of sufficient length to accommodate the saw base , lock washers , hex nuts , and the thickness of the work - bench . TRACEHOLES ATTHESELOCATIONSFOR HOLEPATTERN ATTHESELOCATIONSFOR TRACEHOLES HOLEPATTERN BASE \ MOUNTINGSURFACE Fig . 5 12
Page: 13

Thisproducthasbeenshippedcompletelyassembled • Donotdiscardthepackingmateriaul ntilyouhaveetool . exceptfortheblade , miterlockhandled , ustbag , and carefullyinspectedandsatisfactoriloyperatedth dustguide . • Thesawisfactorysetforaccuratecutting . Afterasures • Carefulllyift sawfromthecartonbythecarryinghandle assemblinigt , checkfor accuracyI . fshippinghed andthesawbase , andplaceit onalevelworksurface . influencetdhesettingsr , eferto specificproc explainedinthismanual . NOTET : hissawisheavyT . oavoidbackinjury , liftwithd . yourlegs , notyourback , andgethelpwhenneede • Ifanypartsaredamagedormissingp , leasecall 1 - 800 - 932 - 318fo8rassistance . • Yoursawhasbeenshippedwiththesawarmsecured inthedownpositionT . oreleasethesawarm , pushpa , downonthetopof thesawarm , cutthetie - wra nd _ k WARNING : Do not attempt to modify this tool or create accessories not recommended for use with pulloutonthelockpin . this tool . Any such alteration or modification is • LiftthesawarmbythehandleH . andpressureshould misuse and could result in a hazardous condition remainonthesawarmto prevenst uddenriseupon leading to possible serious personal injury . releaseofthetiewrap . • Inspectthetoolcarefullyto makesurenobreakageor _ k WARNING : If any parts are missing , do not operate damageoccurredduringshipping . this tool until the missing parts are replaced . Failure to do so could result in possible serious personal injury . The following tools ( not included ) are needed for checking adjustments of your saw or for installing the blade : \ COMBINATIONWRENCH ( 2 ) 17 mm , 10 mm COMBINATIONSQUARE FRAMINGSQUARE Fig . 6 13
Page: 14

ThefollowingitemsareincludedwithyourCompoundMiterSaw : • SawBlade - 10in . • 5mmHexKey • MiterLockHandle • 8 mmHexKey • DustBag • 6mmBladeWrench • DustGuide • Operator'sManual SAWBLADE 6 mm BLADEWRENCH WORKCLAMP DUSTBAG DUSTGUIDE / HEXKEYS ( 2 ) 5 mm , 8 mm U _ IITER LOCKHANDLE Fig . 7 _ k WARNING : The use of attachments or accessories not listed might be hazardous and could cause serious per - sonal injury . 14
Page: 15

DUST GUIDE , _ WARNING : Do not connect to power supply until assembly is complete . Failure to comply could See Figure 9 . result in accidental starting and possible serious To install the dust guide , place the end marked INSERT personal injury . over the exhaust port in the upper blade guard . Turn the guide so that the open end is facing down or toward the As mentioned previously , your saw has been factory as - rear of the saw . sembled and adjusted . The miter lock handle , dust guide , and blade are the only parts that have to be installed . EXHAUST MITER LOCK HANDLE PORT See Figure 8 . Cut the tie - wraps holding the saw arm and the miter lock in place . To install the miter lock handle , place the thread - ed stud into the threaded hole in the control arm . Turn clockwise to tighten . DUST GUIDE Fig . 9 DUST BAG See Figure 10 . A dust bag is provided for use on your miter saw . It fits over the dust guide on the upper blade guard . To install , TO squeeze the two metal clips to open the mouth of the bag LOOSEN and slide it on to the dust guide . Release the clips . The metal ring in the bag should lock in between the grooves on the dust guide . To remove the dust bag for emptying , simply reverse the TO above procedure . TIGHTEN MITER MITER TABLE LOCKHANDLE CONTROL ARM DUSTGUIDE Fig . 8 DUSTBAG Fig . 10 15
Page: 16

WORK CLAMP TO INSTALL BLADE See Figure 11 , See Figures 12 , 13 , and 14 . The work clamp provides greater control by clamping the WARNING : A 10 in . blade is the maximum blade A workpiece to the fence or the saw table . It also prevents the capacity of your saw . Never use a blade that is too workpiece from creeping toward the saw blade . This is very thick to allow outer blade washer to engage with helpful when cutting compound miters . the flats on the spindle . Larger blades will come in Depending on the cutting operation and the size of the contact with the blade guards , while thicker blades workpiece , it may be necessary to use a C - clamp instead will prevent the blade screw from securing the blade of the work clamp to secure the workpiece prior to making on the spindle . Either of these situations could result the cut . in a serious accident and can cause serious personal injury . _ WARNING : In some operations , the work clamp • Unplug your saw . assembly may interfere with the operation of the blade guard assembly . Always make sure there is no interference with the blade guard prior to begin - _ hb WARNING : Failure to unplug your saw could result in accidental starting causing possible serious ning any cutting operation to reduce the risk of personal injury . serious personal injury . • Loosen the phillips screw on the blade bolt cover until Follow these directions to install the work clamp : blade bolt cover can be raised . See Figures 12 and 13 . • Place the shaft of the work clamp in either hole on the • Gently raise the lower blade guard bracket , releasing saw table base . lower blade guard from notch so that lower blade • Rotate the knob on the work clamp to move it in or out guard and blade bolt cover can be rotated up and back as needed . to expose the blade bolt . See Figures 12 and 13 . • Depress the spindle lock button and rotate the blade bolt until the spindle locks . See Figure 13 . _ WARNING : When using any clamp with a stop block , install the clamp on the same side as the stop • Using the blade wrench provided , loosen and remove block . This will eliminate the possibility of trapping the blade bolt . the workpiece , resulting in the saw blade and NOTE : The blade bolt has left hand threads . Turn blade workpiece kicking up . Failure to heed this warning bolt clockwise to loosen . can result in serious personal injury . PHILLIPS SCREW LOWER BLADEGUARD WORKCLAMP NOTCH Fig . 11 LOWERBLADE GUARDBRACKET Fig . 12 16
Page: 17

LOWER _ WARNING : If inner blade washer has been BLADEGUARD removed , replace it before placing blade on spindle . PHILLIPS SCREW Failure to do so could cause an accident since blade will not tighten properly . BLADE BOLTCOVER • Fit saw blade inside lower blade guard and onto spindle . The blade teeth point downward at the front of saw as shown in figure 13 . _ CAUTION : Always install the blade with the blade teeth and the arrow printed on the side of the blade FLAT ( S ) TO pointing down at the front of the saw . The direction ON SPINDLE LOOSEN of blade rotation is also stamped with an arrow on the upper blade guard . INNERBLADE WASHERWITH • Replace outer blade washer . The double " D " flats on DOUBLE " D " FLATS TO the blade washers align with the flats on the spindle . TIGHTEN • Depress spindle lock button and replace blade bolt . BLADE See Figure 14 . BLADEBOLT OUTERBLADEWASHER NOTE : The blade bolt has left hand threads . Turn blade WITH DOUBLE " D " FLATS bolt counterclockwise to tighten . Fig . 13 • Tighten blade bolt securely . • Remove outer blade washer . Do not remove inner • Remove the hex key and store it in rubber grommet behind left - hand fence . blade washer . • Replace the lower blade guard and blade bolt cover . • Wipe a drop of oil onto inner blade washer and outer blade washer where they contact the blade . • Retighten phillips screw securing blade bolt cover . Tighten screw securely . See Figure 13 . SPINDLE LOCK _ WARNING : Make sure the spindle lock button is BUTTON not engaged before reconnecting saw into power source . Never engage spindle lock button when blade is rotating . Your compound miter saw has been adjusted at the fac - tory for making very accurate cuts . However , some of the components might have moved out of alignment during shipping . Also , over a period of time , readjustment will probably become necessary due to wear . After unpacking your saw , check the following adjustments before you be - gin using saw . Make any readjustments that are necessary and periodically check the parts alignment to make sure that your saw is cutting accurately . WARNING : Your saw should never be connected n to a power supply when you are assembling parts , making adjustments , installing or removing blades , or when not in use . Disconnecting your saw will Fig . 14 prevent accidental starting that could cause serious injury . 17
Page: 18

NOTE : nManyoftheillustrationisnthismanuaslhowonlyal FENCE MITERTABLE portionsof yourcompoundmitersaw . Thisisintentioeil - sothatwecanclearlyshowpointsbeingmadeinthguards lustrationsN . everoperateyoursawwithoutallition , securelyinplaceandingoodoperatingcond SQUARING THE MITER TABLE TO THE FENCE See Figures 15 - 18 . • Unplug your saw . _ , WARNING : Failure to unplug your saw could result FRAMING ZEROCLEARANCE in accidental starting causing possible serious SQUARE THROATPLATE personal injury . VIEW OFMITERTABLENOTSQUAREWITH • Push down on the saw arm and pull out the lock pin to FENCE , ADJUSTMENTSAREREQUIRED release the saw arm . Fig . 16 • Raise saw arm to its full raised position . • Loosen the miter lock handle approximately one - half FENCE MITERTABLE turn . • Depress the miter lock plate and rotate the miter table until the pointer on the control arm is positioned at 0 . • Release the miter lock plate and securely tighten the miter lock handle . • Lay a framing square flat on the miter table . Place one leg of the square against the fence . Place the other leg of the square beside the zero clearance throat plate in the miter table . The edge of the square and the zero FRAMING clearance throat plate in the miter table should be par - ZEROCLEARANCE SQUARE allel as shown in figure 15 . THROATPLATE • If the edge of the framing square and the zero clear - VIEWOF MITERTABLENOTSQUAREWITH ance throat plate in the miter table are not parallel as FENCE , ADJUSTMENTSAREREQUIRED shown in figures 16 and 17 , adjustments are needed . Fig . 17 • Using the blade wrench , loosen the socket head FRAMING FENCE SQUARE screws securing the fence . See Figure 18 . Adjust the MITERTABLE fence left or right until the framing square and zero clearance throat plate are parallel . • Retighten the screws securely and recheck the fence - to - table alignment . SOCKETHEAD MITER LOCKPLATE F _ Eq _ N % _ EJ / / / _ II ' - ' II O - ZEROCLEARANCE THROATPLATE MITER LOCKHANDLE VIEWOF MITERTABLESQUAREWITH FENCE CORRECTLYADJUSTED Fig . 18 Fig . 15 18
Page: 19

CUTTING A SLOT IN THE ZERO CLEARANCE FENCE THROAT PLATE BLADE In order to use your compound miter saw , you must cut a slot through the zero clearance throat plate to allow for blade clearance . To cut the slot , set your saw at 0 miter , turn saw on and allow the blade to reach full speed , then MITER carefully make a straight cut as far as it will go through LOCK PLATE the throat plate . Turn your saw off and allow the blade to come to a complete stop before raising the saw arm . Next , adjust the bevel angle to 45 , turn your saw on and FRAMING allow the blade to reach full speed , then carefully make SQUARE BASE MITER another cut through the zero clearance throat plate . The LOCKHANDLE slot in the throat plate will then be wide enough to allow VIEW OFBLADE the blade to pass through it at any angle from 0 ° to 45 . SQUAREWITH FENCE Fig . 19 SQUARING THE SAW BLADE TO THE FENCE See Figures 19 - 22 , • Unplug your saw . BLADE FENCE _ WARNING : Failure to unplug your saw could result in accidental starting causing possible serious personal injury . • Remove the screws securing the throat plate then re - move the throat plate . Save the screws and throat plate for later reinstallation . • Pull the saw arm all the way down and engage the lock pin to hold the saw arm in transport position . MITER FRAMING TABLE SQUARE • Loosen the miter lock handle approximately one - half turn . VIEWOF BLADENOTSQUAREWITH • Depress the miter lock plate and rotate the miter table FENCE , ADJUSTMENTSAREREQUIRED until the pointer on the control arm is positioned at 0 . Fig . 20 • Release the miter lock plate and securely tighten the miter lock handle . • Lay a framing square flat on the miter table . Place one BLADE leg of the square against the fence . Slide the other leg FENCE of the square against the flat part of saw blade . NOTE : Make sure that the square contacts the flat part of the saw blade , not the blade teeth . • The edge of the square and the saw blade should be parallel as shown in figure 19 . • If the front or back edge of the saw blade angles away from the square as shown in figures 20 and 21 , adjust - ments are needed . FRAMING • Using a 8 mm hex key , loosen the socket head screws MITER SQUARE that secure the mounting bracket to the miter table . TABLE See Figure 22 , VIEWOF BLADENOTSQUAREWITH • Rotate the mounting bracket left or right until the saw FENCE , ADJUSTMENTSAREREQUIRED blade is parallel with the square . Fig . 21 • Retighten the screws securely and recheck the blade - to - fence alignment . • Reinstall the throat plate and securely tighten the screws . 19
Page: 20

8 mm SCOKET SQUARING THE BLADE TO THE HEADSCREW ( S ) MITER TABLE See Figures 23 - 25 . • Unplug your saw . _ , WARNING : Failure to unplug your saw could result in accidental starting causing possible serious personal injury . • Pull the saw arm all the way down and engage the lock pin to hold the saw arm in transport position . • Loosen the miter lock handle approximately one - half turn . MITER 8 mm HEXKEY MOUNTING • Depress the miter lock plate and rotate the miter table TABLE BRACKET WRENCH until the pointer on the control arm is positioned at 0 . Fig . 22 • Release the miter lock plate and securely tighten the miter lock handle . • Loosen bevel lock knob and set saw arm at 0 bevel ( blade set 90 to miter table ) . Tighten bevel lock knob . BLADE • Place a combination square against the miter table and the flat part of saw blade . NOTE : Make sure that the square contacts the flat part of the saw blade , not the blade teeth . MITER • Rotate the blade by hand and check the blade - to - table LOCK alignment at several points . PLATE • The edge of the square and the saw blade should be parallel as shown in figure 23 . MITER • If the top or bottom of the saw blade angles away from COMBINATION TABLE the square as shown in figures 24 and 25 , adjustments MITER SQUARE are needed . LOCKHANDLE • Using a 10 mm wrench or adjustable wrench , loosen CORRECTVIEW OFBLADE the lock nut securing positive stop adjustment screw . SQUAREWITH MITERTABLE Also loosen bevel lock knob . See Figure 36 . Fig . 23 • Adjust positive stop adjustment screw to bring saw blade into alignment with the square . FENCE BLADE • Retighten bevel lock knob . Next , retighten lock nut securing the positive stop adjustment screw . Recheck \ blade - to - table alignment . NOTE : The above procedure can be used to check blade squareness of the saw blade to the miter table at both 0 ° and 45 angles . MITER TABLE COMBINATION SQUARE VIEW OFBLADENOTSQUAREWITH MITER TABLE , ADJUSTMENTSAREREQUIRED Fig . 24 2O
Page: 21

BLADE Yoursawhasthreescaleindicatorst , wooneithersideof - thebevesl caleandoneonthemiterscaleA . ftersquarrtyo ingadjustmenthsavebeenmade , it maybenecessa loosentheindicatorsscrewsandresetthemtozero . MITER COMBINATION TABLE SQUARE VIEW OFBLADENOTSQUAREWITH MITER TABLE , ADJUSTMENTSAREREQUIRED Fig . 25 CUTTING WITH YOUR COMPOUND MITER your , _ WARNING : Do not allow familiarity with tool SAW to make you careless . Remember that a careless fraction of a second is sufficient to inflict severe _ Ib WARNING : When using a work clamp or C - clampne injury . to secure your workpiece , clamp workpiece on o side of the blade only . The workpiece must remain _ lh WARNING : Always wear safety goggles or safety free on one side of the blade to prevent the blade glasses with side shields when operating tools . from binding in workpiece . The workpiece binding Failure to do so could result in objects being thrown the blade will cause motor stalling and kickback . into your eyes , resulting in possible serious injury . This situation could cause an accident resulting in possible serious personal injury . APPLICATIONS CROSSCUTTING This product has been designed only for the purposes listed below : See Figure 26 . • Cross cutting wood and plastic . A crosscut is made by cutting across the grain of the workpiece . A straight crosscut is made with the miter • Cross cutting miters , joints , etc . for picture frames , table set at the 0 position . Miter crosscuts are made with moldings , door casings , and fine joinery . the miter table set at some angle other than zero . NOTE : The blade provided is fine for most wood cutting operations , but for fine joinery cuts or cutting plastic , use one of the accessory blades available from your nearest Sears store . , _ WARNING : Before starting any cutting operation , clamp or bolt your compound miter saw to a workbench . Never operate your miter saw on the floor or in a crouched position . Failure to heed this warning can result in serious personal injury . STRAIGHT CROSSCUT Fig . 26 21
Page: 22

TO CROSSCUT WITH YOUR MITER SAW • Before turning on the saw , perform a dry run of the cut - ting operation just to make sure that no problems will • Pull out the lock pin and lift saw arm to its full height . occur when the cut is made . • Loosen the miter lock handle . Rotate the miter lock • Grasp the saw handle firmly then squeeze the switch handle approximately one - half turn to the left to trigger . Allow several seconds for the blade to reach loosen . maximum speed . • Press the miter lock plate down with your thumb and • Slowly lower the blade into and through the workpiece . hold . See Figure 26 . • Rotate the control arm until the pointer aligns with the • Release the switch trigger and allow the saw blade to desired angle on the miter scale . stop rotating before raising the blade out of workpiece . • Release the miter lock plate . Wait until the electric brake stops blade from turning NOTE : You can quickly locate 0 ° , 15 ° , 22 - 1 / 2,30 ° , left before removing the workpiece from the miter table . or right , and 45 ° left or right by releasing the lock plate BEVEL CUT as you rotate the control arm . The lock plate will seat See Figures 27 and 28 . itself in one of the positive stop notches , located in the base . A bevel cut is made by cutting across the grain of the workpiece with the blade angled to the workpiece . A • Tighten the miter lock handle securely . straight bevel cut is made with the miter table set at the zero degree position and the blade set at an angle be - _ I = WARNING : To avoid serious personal injury , always tween 0 and 45 ° . tighten the miter lock handle securely before making a cut . Failure to do so could result in movement of LEFTSIDE I RIGHTSIDE the control arm or miter table while making a cut . I LEFT RIGHTTOR SCALE INDICATOR INDICA • Place the workpiece flat on the miter table with one POINT POINT edge securely against the fence . If the board is warped , place the convex side against the fence . If the concave edge of a board is placed against the fence , the board could collapse on the blade at the end of the cut , jam - ming the blade . • When cutting long pieces of lumber or molding , sup - port the opposite end of the stock with a roller stand or with a work surface level with the saw table . See Figure 31 . • Align cutting line on the workpiece with the edge of SCALE MOUNTINGBRACKET saw blade . Fig . 27 • Grasp the stock firmly with one hand and secure it against the fence or use the optional work clamp or a C - clamp to secure the workpiece . See Figure 26 . _ IL WARNING : To avoid serious personal injury , keep n your hands outside the no hands zone ; at least 3 in . from blade . Never perform any cutting operation freehand ( without holding workpiece against the fence ) . The blade could grab the workpiece if it slips or twists . 22
Page: 23

TO BEVEL CUT WITH YOUR MITER SAW • Pull out the lock pin and lift saw arm to its full height . BEVELCUT • Loosen the miter lock handle . Rotate the miter lock handle approximately one - half turn to the left to loosen . • Press the miter lock plate down with your thumb and hold . • Rotate the control arm until the pointer aligns with zero on the miter scale . • Release the miter lock plate . NOTE : You can quickly locate zero by releasing the lock plate as you rotate the control arm . The lock plate will seat itself in one of the built - in positive stop notches , located in the base . • Tighten the miter lock handle securely . A WARNING : To avoid serious personal injury , always N tighten the miter lock handle securely before making a cut . Failure to do so could result in movement of the control arm or miter table while making a cut . Fig . 28 • Loosen the bevel lock knob and move the saw arm to WARNING : To avoid serious personal injury , keep the left to the desired bevel angle . your hands outside the no hands zone ; at least 3 in . from blade . Never perform any cutting operation • Bevel angles can be set from 0 to 45 . freehand ( without holding workpiece against the • For your convenience there is a double scale located fence ) . The blade could grab the workpiece if it slips on the mounting bracket . See Figure 27 . If one side or twists . becomes difficult to read as you move the saw arm to the left , simply refer to the other side . Align the • Before turning on the saw , perform a dry run of the cut - indicator point for the side you choose with the desired ting operation just to make sure that no problems will angle . occur when the cut is made . • Once the saw arm has been set at the desired angle , • Grasp the saw handle firmly then squeeze the switch securely tighten the bevel lock knob . trigger . Allow several seconds for the blade to reach • Place the workpiece flat on the miter table with one maximum speed . edge securely against the fence . If the board is warped , • Slowly lower the blade into and through the workpiece . place the convex side against the fence . If the concave See Figure 28 . edge of a board is placed against the fence , the board • Release the switch trigger and allow the saw blade to could collapse on the blade at the end of the cut , jam - stop rotating before raising the blade out of workpiece . ming the blade . See Figures 33 and 34 . Wait until the electric brake stops blade from turning • When cutting long pieces of lumber or molding , sup - before removing the workpiece from miter table . port the opposite end of the stock with a roller stand or with a work surface level with the saw table . See Figure 31 . • Align the cutting line on the workpiece with the edge of saw blade . • Grasp the stock firmly with one hand and secure it against the fence or use the optional work clamp or a C - clamp to secure the workpiece . See Figure 28 . 23
Page: 24

COMPOUND MITER CUT • Once the saw arm has been set at the desired angle , securely tighten the bevel lock knob . A compound miter cut is a cut made using a miter angle and a bevel angle at the same time . This type of cut is • Recheck miter angle setting . Make a test cut in scrap material . used to make picture frames , cut molding , make boxes with sloping sides , and for certain roof framing cuts . • Place the workpiece flat on the miter table with one edge securely against the fence . If the board is warped , To make this type of cut the control arm on the miter table place the convex side against the fence . If the concave must be rotated to the correct angle and the saw arm edge of a board could collapse on the blade at the end must be tilted to the correct bevel angle . Care should al - of the cut , jamming the blade . See Figures 33 and 34 . ways be taken when making compound miter setups due to the interaction of the two angle settings . • When cutting long pieces of lumber or molding , sup - port the opposite end of the stock with a roller stand Adjustments of miter and bevel settings are interde - or with a work surface level with the saw table . See pendent with one another . Each time you adjust the miter Figure 31 . setting you change the effect of the bevel setting . Also , • Align the cutting line on the workpiece with the edge of each time you adjust the bevel setting you change the ef - saw blade . fect of the miter setting . • Grasp the stock firmly with one hand and secure it It may take several settings to obtain the desired cut . The against the fence or use the optional work clamp or a first angle setting should be checked after setting the C - clamp to secure the workpiece when possible . See second angle , since adjusting the second angle affects Figure 29 . the first . NOTE : When making a 45 ° left miter and a bevel angle Once the two correct settings for a particular cut have greater than 30 ° , you must use a C - clamp to secure the been obtained , always make a test cut in scrap material workpiece or move clamp to the right side of the base . before making a finish cut in good material . TO MAKE A COMPOUND CUT WITH YOUR _ i , WARNING : To avoid serious personal injury , always keep your hands outside the no hands zone ; at least MITER SAW 3 in . from blade . Never perform any cutting opera - • Pull out the lock pin and lift saw arm to its full height . tion freehand ( without holding workpiece against the • Loosen the miter lock handle . Rotate the miter lock fence ) . The blade could grab the workpiece if it slips handle approximately one - half turn to the left to or twists . loosen . • Press the miter lock plate down with your thumb and • Before turning on the saw , perform a dry run of the cut - hold . ting operation just to make sure that no problems will occur when the cut is made . • Rotate the control arm until the pointer aligns with the desired angle on the miter scale . • Grasp the saw handle firmly then squeeze the switch • Release the miter lock plate . trigger . Allow several seconds for the blade to reach NOTE : You can quickly locate 0 ° , 15 ° , 22 - 1 / 2 ° , 30 ° , left maximum speed . or right , and 45 ° left or right by releasing the miter lock plate as you rotate the control arm . The miter lock plate will seat itself in one of the positive stop notches , located in miter table frame . • Tighten the miter lock handle securely . COMPOUND WARNING : To avoid serious personal injury , MITER CUT _ IL always tighten the miter lock handle securely before making a cut . Failure to do so could result in movement of the control arm or miter table while making a cut . Loosen the bevel lock knob and move the saw arm to the left to the desired bevel angle . Bevel angles can be set from 0 ° to 45 ° . For your convenience there is a double scale located on the mounting bracket . See Figure 27 . If one side be - comes difficult to read as you move the saw arm to the left , simply refer to the other side . Align the indicator point for the side you choose with the desired angle . Fig . 29 24
Page: 25

• Slowly lower the blade into and through the work - piece . See Figure 29 . • Release the switch trigger and allow the saw blade to stop rotating before raising the blade out of workpiece . Wait until the electric brake stops blade from turning before removing the workpiece from miter table . SUPPORT LONG WORKPIECES See Figure 31 . Long workpieces need extra supports . Supports should be placed along the workpiece so it does not sag . The support should let the workpiece lay flat on the base of the saw and work table during the cutting operation . Use the optional work clamp or a C - clamp to secure the workpiece . , _ WARNING : To avoid serious personal injury , aalwaysst keep your hands outside the no hands zone ; at le 3 in . from blade . Never perform any cutting operation freehand ( without holding workpiece against the fence ) . The blade could grab the workpiece if it slips or twists . 45 ° X 45 ° COMPOUNDMITER CUT Fig . 30 LONGWORKPIECE WORKPIECESUPPORTS Fig . 31 25
Page: 26

CUTTING COMPOUND MITERS To aid in making the correct settings , the compound angle setting chart below has been provided . Since compound cuts are the most difficult to accurately obtain , trial cuts should be made in scrap material , and much thought and planning made , prior to making your required cut . NUMBER OF SIDES PITCH OFSIDE 4 I 5 I 6 I 7 8 I 9 I 10 M - 45.00 ° M - 36.00 ° M - 30.00 ° M - 25.71 ° M - 22.50 ° M - 20.00 ° M - 18.00 ° 0o B - 0.00 ° B - 0.00 ° B - 0.00 ° B - 0.00 ° B - 0.00 ° B - 0.00 ° B - 0.00 ° M - 44.89 ° M - 35.90 ° M - 29.91 ° M - 25.63 ° M - 22.42 ° M - 19.93 ° M - 17.94 ° 5 ° B - 3.53 ° B - 2.94 ° B - 2.50 ° B - 2.17 ° B - 1.91 ° B - 1.71 ° B - 1.54 ° M - 44.56 ° M - 35.58 ° M - 29.62 ° M - 25.37 ° M - 22.19 ° M - 19.72 ° M - 17.74 ° 10 ° B - 7.05 ° B - 5.86 ° B - 4.98 ° B - 4.32 ° B - 3.81 ° B - 3.40 ° B - 3.08 ° M - 44.01 ° M - 35.06 ° M - 29.15 ° M - 24.95 ° M - 21.81 ° M - 19.37 ° M - 17.42 ° 15 ° B - 10.55 ° B - 8.75 ° B - 7.44 ° B - 6.45 ° B - 5.68 ° B - 5.08 ° B - 4.59 ° M - 43.22 ° M - 34.32 ° M - 28.48 ° M - 24.35 ° M - 21.27 ° M - 18.88 ° M - 16.98 ° 20 ° B - 14.00 ° B - 11.60 ° B - 9.85 ° B - 8.53 ° B - 7.52 ° B - 6.72 ° B - 6.07 ° M - 42.19 ° M - 33.36 ° M - 27.62 ° M - 23.56 ° M - 20.58 ° M - 18.26 ° M - 16.41 ° 25 ° B - 17.39 ° B - 14.38 ° B - 12.20 ° B - 10.57 ° B - 9.31 ° B - 8.31 ° B - 7.50 ° 30 ° M - 40.89 ° M - 32.18 ° M - 26.57 ° M - 22.64 ° M - 19.73 ° M - 17.50 ° M - 15.72 ° ° B - 20.70 ° B - 17.09 ° B - 14.48 ° B - 12.53 ° B - 11.03 ° B - 9.85 ° B - 8.89 M - 39.32 ° M - 30.76 ° M - 25.31 ° M - 21.53 ° M - 18.74 ° M - 16.60 ° M - 14.90 ° 35 ° B - 23.93 ° B - 19.70 ° B - 16.67 ° B - 14.41 ° B - 12.68 ° B - 11.31 ° B - 10.21 ° M - 37.45 ° M - 29.10 ° M - 23.86 ° M - 20.25 ° M - 17.60 ° M - 15.58 ° M - 13.98 ° 40 ° B - 27.03 ° B - 22.20 ° B - 18.75 ° B - 16.19 ° B - 14.24 ° B - 12.70 ° B - 11.46 ° M - 35.26 ° M - 27.19 ° M - 22.21 ° M - 18.80 ° M - 16.32 ° M - 14.43 ° M - 12.94 ° 45 ° B - 30.00 ° B - 24.56 ° B - 20.70 ° B - 17.87 ° B - 15.70 ° B - 14.00 ° B - 12.62 ° M - 32.73 ° M - 25.03 ° M - 20.36 ° M - 17.20 ° M - 14.91 ° M - 13.17 ° M - 11.80 ° 50 ° B - 32.80 ° B - 26.76 ° B - 22.52 ° B - 19.41 ° B - 17.05 ° B - 15.19 ° B - 13.69 ° M - 29.84 ° M - 22.62 ° M - 18.32 ° M - 15.44 ° M - 13.36 ° M - 11.79 ° M - 10.56 ° 55 ° B - 35.40 ° B - 28.78 ° B - 24.18 ° B - 20.82 ° B - 18.27 ° B - 16.27 ° B - 14.66 ° M - 26.57 ° M - 19.96 ° M - 16.10 ° M - 13.54 ° M - 11.70 ° M - 10.31 ° M - 9.23 ° 60 ° B - 37.76 ° B - 30.60 ° B - 25.66 ° B - 22.07 ° B - 19.35 ° B - 17.23 ° B - 15.52 ° M - 22.91 ° M - 17.07 ° M - 13.71 ° M - 11.50 ° M - 9.93 ° M - 8.74 ° M - 7.82 ° 65 ° B - 39.86 ° B - 32.19 ° B - 26.95 ° B - 23.16 ° B - 20.29 ° B - 18.06 ° B - 16.26 ° M - 18.88 ° M - 13.95 ° M - 11.17 ° M - 9.35 ° M - 8.06 ° M - 7.10 ° M - 6.34 ° 70 ° B - 41.64 ° B - 33.53 ° B - 28.02 ° B - 24.06 ° B - 21.08 ° B - 18.75 ° B - 16.88 ° 75 ° M - 14.51 ° M - 10.65 ° M - 8.50 ° M - 7.10 ° M - 6.12 ° M - 5.38 ° M - 4.81 ° ° B - 43.08 ° B - 34.59 ° B - 28.88 ° B - 24.78 ° B - 21.69 ° B - 19.29 ° B - 17.37 M - 9.85 ° M - 7.19 ° M - 5.73 ° M - 4.78 ° M - 4.11 ° M - 3.62 ° M - 3.23 ° 80 ° B - 44.14 ° B - 35.37 ° B - 29.50 ° B - 25.30 ° B - 22.14 ° B - 19.68 ° B - 17.72 ° M - 4.98 ° M - 3.62 ° M - 2.88 ° M - 2.40 ° M - 2.07 ° M - 1.82 ° M - 1.62 ° 85 ° B - 44.78 ° B - 35.84 ° B - 29.87 ° B - 25.61 ° B - 22.41 ° B - 19.92 ° B - 17.93 ° M - 0.00 ° M - 0.00 ° M - 0.00 ° M - 0.00 ° M - 0.00 ° M - 0.00 ° M - 0.00 ° 90 ° B - 45.00 ° B - 36.00 ° B - 30.00 ° B - 25.71 ° B - 22.50 ° B - 20.00 ° B - 18.00 ° Each B ( Bevel ) and M ( Miter ) Setting is Given to the Closest 0.005 ° . COMPOUND - ANGLE SETTINGS FOR POPULAR STRUCTURES 26
Page: 27

CUTTING CROWN MOLDING When setting the bevel and miter angles for compound miters , remember that the settings are interdependent ; Your compound miter saw does an excellent job of cutting changing one angle changes the other angle as well . crown molding . In general , compound miter saws do a better job of cutting crown molding than any other tool Keep in mind that the angles for crown moldings are very made . precise and difficult to set . Since it is very easy for these angles to shift , all settings should first be tested on scrap In order to fit properly , crown molding must be compound molding . Also most walls do not have angles of exactly mitered with extreme accuracy . 90 , therefore , you will need to fine tune your settings . The two contact surfaces on a piece of crown molding When cutting crown molding by this method the bevel that fit flat against the ceiling and the wall of a room are at angle should be set at 33.85 The miter angle should be angles that , when added together , equal exactly 90 . Most set at 31.62 either right or left , depending on the desired crown molding has a top rear angle ( the section that fits cut for the application . See the chart below for correct flat against the ceiling ) of 52 and a bottom rear angle ( the angle settings and correct positioning of crown molding section that fits flat against the wall ) of 38 ° . on miter table . LAYING MOLDING FLAT ON THE The settings in the chart below can be used for cutting All Standard ( U . S . ) crown molding with 52 ° and 38 angles . MITER TABLE The crown molding is placed flat on the miter table using See Figure 32 . the compound features of your miter saw . To use this method for accurately cutting crown molding for a 90 inside or outside corner , lay the molding with its broad back surface flat on the miter table and against the fence . 52 ° CEILING 38 _ WL INSIDE L FENCE CORNER OUTSIDE TOPEDGEAGAINSTFENCE = FENCE CORNER LEFTSIDE , INSIDECORNER BOTTOMEDGEAGAINSTFENCE = RIGHTSIDE , OUTSIDECORNER • RIGHTSIDE , INSIDECORNER • LEFTSIDE , OUTSIDECORNER MITERTABLE MITERTABLE 0 0 CROWNMOLDINGFLATONMITERTABLE Fig . 32 27
Page: 28

Bevel Angle Type of Cut Settin £ Left side , inside corner 1 . Top edge of molding against fence 33.85 2 . Miter table set right 31.62 3 . Save left end of cut Right side , inside corner 1 . Bottom edge of molding against fence 33.85 2 . Miter table set left 31.62 3 . Save left end of cut Left side , outside corner 1 . Bottom edge of molding against fence 33.85 2 . Miter table set left 31.62 3 . Save right end of cut WRONG Fig . 34 Right side , outside corner _ , WARNING : To avoid a kickback and to avoidoncave 1 . Top edge of molding against fence serious personal injury , never position the c 33.85 : 2 . Miter table set right 31.62 edge of bowed or warped material against the fence . 3 . Save right end of cut CLAMPING WIDE WORKPIECES See Figure 35 . CUTTING WARPED MATERIAL When cutting wide workpieces such as a 2 in . x 6 in . , boards should be clamped with a C - clamp as shown in See Figures 33 and 34 . figure 35 . When cutting warped material , always make sure it is positioned on the miter table with the convex side against the fence as shown in figure 33 . If the warped material is positioned the wrong way as shown in figure 34 , it will pinch the blade near the comple - tion of the cut . WIDE BOARD RIGHT Fig . 33 Fig . 35 28
Page: 29

BEVEL PIVOT ADJUSTMENT _ i , WARNING : Beforeperforminganyadjustment , makesurethetoolisunpluggedfromthepower • Your compound miter saw should bevel easily by loos - supplyandtheswitchisintheOFF ( I ) position . ening the bevel lock knob and tilting the saw arm to the Failureto heedthiswarningcouldresultinserious left . personailnjury . • If movement is tight or if there is play in the pivot , have saw repaired by a qualified service technician at your nearest Sears store or repair center to avoid risk of personal injury . POSITIVESTOP DEPTH STOP ADJUSTMENT See Figure 37 , SCREWFOR The depth stop limits the blade's downward travel . It 45 ° ANGLES allows the blade to go below the miter table enough to maintain full cutting capacities . The depth stop positions LOCKNUT ( S ) the blade 1 / 4 in . from the miter table support . NOTE : The miter table support is located inside miter table . The depth stop is factory set to provide maximum cut - ting capacity for the 10 in . saw blade provided with your saw . Therefore , the saw blade provided should never need adjustments . However , when the diameter of the blade has been re - \ duced due to sharpening , it may be necessary to adjust the depth stop to provide maximum cutting capacity . Also , when a new blade is installed , it is necessary to check the Fig . 36 clearance of the blade to the miter table support before starting the saw . Make adjustments if needed . PIVOT ADJUSTMENTS NOTE : These adjustments were made at the factory and normally do not require readjustment . TRAVEL PIVOT ADJUSTMENT • The saw arm should rise completely to the up position by itself . • If the saw arm does not raise by itself or if there is play in the pivot joints , have saw repaired by a qualified service technician at your nearest Sears store or repair center to avoid risk of personal injury . 29
Page: 30

• Use a 5 mm hex key wrench to adjust the depth stop ° EPSTT . OP adjustment screw . The saw blade is lowered by turning A ° J ° ST . E . T BEVEL the screw counter - clockwise and raised by turning the screw clockwise . SCREW _ ' _ ' / " _ LOCKKNOBMITRE • Lower the blade into the zero clearance throat plate of the miter table . Check blade clearance and maximum cutting distance ( distance from fence where blade enters ) to front of miter table slot . • Readjust if necessary . • Tighten the hex nut with a 17 mm wrench or adjustable wrench . • To prevent the depth stop adjustment screw from turn - ing while tightening the hex nut , carefully hold it with the hex key wrench while tightening the hex nut . ! POSITIVE STOPADJUSTMENT SCREWFOR0 ° ANGLES Fig , 37 _ k WARNING : Do not start your compound miter sawde without checking for interference between the bla and the miter table support . Damage could result to the blade if it strikes the miter table support during operation of the saw . DEPTH STOP ADJUSTMENTS See Figure 37 , • Unplug your saw . _ k WARNING : Failure to unplug your saw could result in accidental starting causing possible serious personal injury . • To adjust the depth stop use a 17 mm wrench or ad - justable wrench and loosen the hex nut at the rear of the miter saw arm . 30
Page: 31

_ k WARNING : Whenservicingu , seonlyidentical t _ . , , . . , . . . , . . . B , , R . _ USH Craftsmanreplacemenptarts . Useof anyotherpart CAP maycreatea hazardorcauseproductdamage . BRUSH _ , WARNING : Always wear safety goggles or tsafetyion glasses with side shields during power tool opera ASSEMBLY or when blowing dust . If operation is dusty , also wear a dust mask . GENERAL Avoid using solvents when cleaning plastic parts . Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use . Use clean cloths to remove dirt , carbon dust , etc . _ , WARNING : Do not at any time let brake fluids , gasoline , petroleum - based products , penetrating BRUSH BRUSH oils , etc . come in contact with plastic parts . ASSEMBLY CAP Chemicals can damage , weaken or destroy plastic which may result in serious personal injury . Fig . 38 It has been found that electric tools are subject to acceler - BRUSH REPLACEMENT ated wear and possible premature failure when they are See Figure 38 . used on fiberglass boats , sports cars , wallboard , spack - Your saw has externally accessible brush assemblies that ling compounds , or plaster . The chips and grindings from should be periodically checked for wear . these materials are highly abrasive to electric tool parts such as bearings , brushes , commutators , etc . Conse - Proceed as follows when replacement is required : quently , it is not recommended that this tool be used for • Unplug your saw . extended work on any fiberglass material , wallboard , your spackling compounds , or plaster . During any use on these _ WARNING : Failure to unplug saw could result in accidental starting causing serious injury . materials it is extremely important that the tool is cleaned frequently by blowing with an air jet . • Remove brush cap with a screwdriver . Brush assembly is spring loaded and will pop out when you remove LUBRICATION brush cap . All of the bearings in this tool are lubricated with a suffi - • Remove brush assembly . cient amount of high grade lubricant for the life of the unit • Check for wear . Replace both brushes when either has under normal operating conditions . Therefore , no further less than 1 / 4 in . length of carbon remaining , Do not lubrication is required . replace one side without replacing the other . • Reassemble using new brush assemblies . Make sure ensure safety reliability , _ k WARNING : To and all curvature of brush matches curvature of motor and repairs - - with the exception of the externally that brush moves freely in brush tube , accessible brushes - - should be performed by a qualified service technician at a Sears store to avoid • Make sure brush cap is oriented correctly ( straight ) and risk of personal injury . replace . • Tighten brush cap securely , Do not overtighten . 31
Page: 32

CRAFTSMAN COMPOUND MINTER SAW - MODEL NUMBER 315.212040 NGURE A 24 23 - - 22 19 27 12 32
Page: 33

CRAFTSMAN COMPOUND MINTER SAW - MODEL NUMBER 315.212040 The mode , number , A4Hbe found On a p , ate attached to the motor hous , ng . Ak _ ays mention the mode , ] number in all correspondence regarding your Oompound Miter Saw or when ordering repair parts . / J PARTS LiST - FIGURE A Key Part No . Number Description Qty . $ 51100300 Base and Table Assembly 1 511106000 Fence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 A07103080457 * Socket Head Cap Screw ( M8 x 45 ram ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 A36030814204 * Lock Washer ( M8 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4 A19003040093 * Screw ( M4 x 9 mm Pan Hd . ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 5 518106300 Table Sp , ndle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 6 A35031025153 * Flat Washer ( M10 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 7 A36131020100 * Lock Washer ( M10 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 8 A31703010008 * Lock Nut ( M10 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 9 A36030612157 * Spring Washer ( M6 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 10 A07003060257 * Socket Head Oap Screw ( M6 x 25 mm Pan Hd . ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 11 518104200 Oontrol Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 12 511107000 Lock Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 13 580114000 Po , nter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 14 A35030410018 * Flat Washer ( M4 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 15 A10003040107 * Screw ( M4 x 10 mm Pan Hd . ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 16 518105400 Lock Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 17 A49001020056 R , vet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 18 511108000 Miter Scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 19 511105000 Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 20 580120000 Fixed Oap ( Grommet ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 21 511104000 Table Hold Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 22 518A08130 Vise Olamp Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 23 512106000 Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 24 589027202 Throat Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 25 A16003040083 * Screw ( M4 x 8 mm Flat Hd . ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 26 588072000 No Hands Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 27 588071004 Line Warning Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 28 511109000 Insert Plate Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 * Standard Hardware Item - May Be Purchased Locally 33
Page: 34

CRAFTSMAN COMPOUND MINTER SAW - MODEL NUMBER 315.212040 FmGURE B 3 SEE NOTE " " 12 11 17 NOTE : The assembly shown represents an important part of the double insulated system . To avoid the possibility of alteration or damage to the system , service should be performed by your nearest Sears Repair Center . Contact your nearest Sears retail store for service center information . 34
Page: 35

CRAFTSMAN COMPOUND MINTER SAW - MODEL NUMBER 315.212040 number in all correspondence regarding your Compound Miter Saw or when ordering repair parts . I he model number will be found on a plate attached to the motor housing . Always mention the model 1 J PARTS LmST - FmGURE B Key Part No . Number Description Qty . 1 528311004 Brush Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 A10003060160 * Screw ( M6 x 16 mm Pan Hd . ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3 588006100 Brush Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 4 A47000060002 E - Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 5 511328000 Carry Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 6 578310008 Warning Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 7 511329000 Data Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 8 A30003010007 * Hex Nut ( M10 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 9 A18003100206 * Set Screw ( M10 x 20 ram ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 10 A30003012194 * Hex Nut ( M12 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 11 A36031226023 * Flat Washer ( M12 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 12 588026106 Spind } e Lock Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 13 A47000040006 E - Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 14 588027005 Compression Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 15 511X03040 Arbor Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 16 588031004 * Special Screw ( M5 x 10 mm ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 17 588021203 Rubber Sleeve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ! 18 A90003040167 * Screw ( M4 x 16 mm Pan Hd . ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 19 588022300 Stop Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 20 A6300000005 ! O - Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 21 588023001 Stop Pin Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 * Standard Hardware item - May Be Purchased Locally 35
Page: 36

CRAFTSMAN COMPOUND MINTER SAW - MODEL NUMBER 315.212040 FmGURE C 3 17 2 ½ 36
Page: 37

CRAFTSMAN COMPOUND MINTER SAW - MODEL NUMBER 315.212040 number in all correspondence regarding your Compound Miter Saw or when ordering repair parts . I he model number will be found on a plate attached to the motor housing . Always mention the model ] J PARTS UST - FmGURE C Key Part No . Number Description Qty . 1 511D04020 Support Bracket Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 A30003006003 * Hex Nut ( M6 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3 578206000 * Hex Bolt ( M6 x 16 ram ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 4 A49001020056 Rivet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 5 511203000 Bevel Scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 6 A07003100256 * Socket Head Oap Screw ( M10 x 25 ram ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 7 A36031018255 * Lock Washer ( M10 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 8 578203007 Pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 9 A35030410018 * Flat Washer ( M4 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 10 A10003040107 * Screw ( M4 x 10 mm Pan Hd . ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 11 578205106 Pivot Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 12 588058103 Lock Bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 13 589011308 Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 14 589010200 Pivot Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 15 A35031025153 * Flat VVasher ( M ! 0 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 16 511202000 Bevel Lock Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 17 580319000 Tension Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 983000 = 471 Operator's Manual * Standard Hardware item - May Be Purchased Locally 37
Page: 38

CRAFTSMAN COMPOUND MINTER SAW - MODEL NUMBER 315.212040 PARTS UST - FmGURE D 13 21 25 26 27 12 22 23 2 29 12 11 4 10 / / 5 6 38
Page: 39

CRAFTSMAN COMPOUND MITER SAW - MODEL NUMBER 315o212040 The model number wit ! be found on a plate at ached to the motor housing . AMtays mention the mode 1 number in all correspondence regarding your Compound Miter Saw or when ordering repair parts . J PARTS LmST - FmGURE D Key Part No . Number Description Qty . 1 $ 51100200 Lower Guard Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 511D06010 Retaining Spring Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3 511406000 Lower Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 4 A35010616105 * Flat Washer ( M6 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 5 A31703006004 * Lock Nut ( M6 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 6 976740 = 001 Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 7 589015108 Shoulder Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 8 538417000 Retaining Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 9 566407000 Roller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 10 589021300 Retract Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 11 580412000 Hex Washer Hand Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 12 588035105 Flange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 13 511512000 Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 14 555412000 Cover Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 15 A10003050106 * Screw ( M5x 10 mm Pan Hd . ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 16 A19001040091 * Screw ( M4 x 9 mm Pan Hd . ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 17 595015001 Logo Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 18 $ 51100100 Upper Guard Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 19 A63020000428 O = Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 20 595026002 Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 ! A10003050105 * Screw ( M5 x 10 mm Pan Hd . ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 22 589034005 Deflector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 23 A35030519105 * Flat Washer ( M5 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 24 A31703004006 * Lock Nut ( M4 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 25 A31703005005 * Lock Nut ( M5 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 26 589032207 Stopper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 27 A10003040152 * Screw ( M4x 15 mm Pan Hd . ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 28 581410003 Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 29 511516000 Dust Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 30 A07910520000 * Hex Key ( 5 ram ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 31 A07810622000 * Blade Wrench ( 6 ram ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 32 A079 ! 0820000 * Hex Key ( 8 mm ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 * Standard Hardware Item - May Be Purchased Locally 39
Page: 40

Your Home For repair - in your home - of all major brand appliances , lawn and garden equipment , or heating and cooling systems , no matter who made it , no matter who sold it ! . . . . . . . . . . . . . . . . . . For the replacement parts , accessories and owner's manuals that you need to do - it - yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . For Sears professional installation of home appliances and items like garage door openers and water heaters . . . . . . . . . . . . . . . . . . . 1 - 8 00 - 4 - MY - H 0 ME ® ( 1 - 800 - 469 - 4663 ) oaa , , n t , o , o , oht soOd aoada . . . . . . . . . . . . . . . . . . www . sears . com www . sears . ca OuHr ome For repair of carry - in items like vacuums , lawn equipment , and electronics , call or go on - line for the location of your nearest Sears Parts & Repair Center . 1 - 800 - 488 - 1222 Call anytime , day or night ( U . S . A . only ) www . sears . com To purchase a protection agreement ( U . S . A . ) or maintenance agreement ( Canada ) on a product serviced by Sears : 1 - 800 - 827 - 6655 ( U . S . A . ) 1 - 800 - 361 - 6665 ( Canada ) Pard pedir servicio de reparacien Au Canada pour service en frangais : a domicilio , y para ordenar piezas . 1 - 800 - LE - FOYER Mc 1 - 8 88 - S U - HOGAR sM ( 1 - 800 - 533 - 6937 ) ( 1 - 888 - 784 - 6427 ) www . sears . ca . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SEARS SM ® Registered Trademark / TMTrademark / Service Mark of Sears , Roebuck and Co . TM SM ® Marca Registrada / Marca de F _ brica / Marca de Servicio de Sears , Roebuck and Co . MC MD Marque de commerce / Marque d6pos6e de Sears , Roebuck and Co . ® Sears , Roebuck and Co .
Search in Miter Saw on ebay
"
* Clicking the part number will send you to Sears Parts Direct.
0S51100300 Base and table assembly
0983000-471 Owners manual
0983000-471R Repair sheet
1511106000 Fence
10A07003060257 Screw
11518104200 Control arm
12511107000 Lock handle
13580114000 Pointer
14A35030410018 Flat washer (m4)(standard hardware item-may be ...
15A10003040107 Screw
16518105400 Lock plate
17A49001020056 Rivet (3)
18511108000 Miter scale
19511105000 Base
2A07103080457 Socket head cap screw (m8 x 45mm)(4)(standard h...
20580120000 Fixed cap (grommet)
21511104000 Table hold down
22518A08130 Miter clamp assembly
23512106000 Table
24589027202 Throat plate
25A16003040083 Screw
26588072000 No hands label (2)
27588071004 Line warning label (2)
28511109000 Insert plate label
3A36030814204 Lock washer (m8)(4)(standard hardware item-may ...
4A19003040093 Screw
5518106300 Spindle
6A35031025153 Flat washer (m10)(2)(standard hardware item-may...
7A36131020100 Lock washer (m10)(standard hardware item-may be...
8A31703010008 Nylon lock nut (m10) (standard hardware item - ...
9A36030612157 Spring washer (m6)(2)(standard hardware item-ma...
0983000-471 Owners manual
0983000-471R Repair sheet
1528311004 Brush cap (2)
10A30003012194 Hex nut (m12)(2)(standard hardware item-may be ...
11A36031226023 Flat washer (m12)(standard hardware item-may be...
12588026106 Spindle lock pin
13A47000040006 E-ring (e4)
14588027005 Compression spring
15511X03040 Arbor assembly
16588031004 Special screw (m5 x 10mm)(2)(standard hardware ...
17588021203 Sleeve
18A90003040167 Screw (m4 x 16mm pan hd.)(standard hardware ite...
19588022300 Stop pin
2A10003060160 Screw
20A63000000051 O-ring
21588023001 Stop pin cap
3588006100 Brush assembly (2)
4A47000060002 E-ring (e6)(2)
5511328000 Carry handle
6578310008 Warning label
7511329000 Data plate
8A30003010007 Hex nut (m10)(standard hardware item-may be pur...
9A18003100206 Set screw (m10 x 20mm)(standard hardware item-m...
0983000-471 Owners manual
0983000-471R Repair sheet
1511D04020 Bracket
10A10003040107 Screw
11578205106 Pivot support
12588058103 Stop bolt
13589011308 Washer
14589010200 Pivot shaft
15A35031025153 Flat washer (m10)(standard hardware item-may be...
16511202000 Bevel lock knob
17580319000 Spring
2A30003006003 Hex nut (m6)(2)(standard hardware item-may be p...
3578206000 Hex bolt (m6 x 16mm)(2)(standard hardware item-...
4A49001020056 Rivet (3)
5511203000 Bevel scale
6A07003100256 Socket head cap screw (m10 x 25mm)(2)(standard ...
7A36031018255 Lock washer (m10)(3)(standard hardware item-may...
8578203007 Bevel indicator (left)
9A35030410018 Flat washer (m4)(2)
0983000-471 Owners manual
0983000-471R Repair sheet
1S51100200 Lower guard assembly
10589021300 Retract spring
11580412000 Hex washer hand screw
12588035105 Blade flange
13511512000 Blade
14555412000 Warning label, upper guard
15A10003050106 Screw (m5 x 10mm pan hd.)(4)(standard hardware ...
16A19001040091 Screw
17595015001 Logo plate
18S51100100 Upper guard assembly
19A63020000428 O-ring
2511D06010 Retaining spring holder
20595026002 Elbow
21A10003050105 Screw
22589034005 Deflector
23A35030519105 Flat washer (m5)(standard hardware item-may be ...
24A31703004006 Self-locking nut (m4) (standard hardware item--...
25A31703005005 Lock nut (m5)(standard hardware item-may be pur...
26589032207 Stopper
27A10003040152 Screw
28581410003 Screw
29511516000 Dust bag
3511406000 Lower guard
30A07910520000 Hex key (5mm)(standard hardware item-may be pur...
31A07810622000 Wrench
32A07910820000 Allen wrench (8mm) (standard hardware item--may...
4A35010616105 Washer
5A31703006004 Nut
6976740-001 Label (1)
7589015108 Shoulder screw
8538417000 Retaining ring (1)
9566407000 Roller (1)
0983000-471 Owners manual
0983000-471R Repair sheet
1511325000 Power cord
10A10003040250 Screw (m4 x 25mm pan hd.)(2)(standard hardware ...
11511323000 D-handle, upper
12511308000 Spring
13511307100 Trigger
14A30003004005 Hex nut (m4)(standard hardware item-may be purc...
159053X02000 Field
16A90101050603 Screw
17511324000 Fan case
18A50006080049 Ball bearing
199053X01000 Armature
2588004100 Strain relief
20A46000150008 C-ring (s-15)(2)
21A50060020056 Bearing
22A63020000320 O-ring
23511327000 Arm
24A30003010007 Hex nut (m10)(standard hardware item-may be pur...
25A18003100206 Screw (m10 x 20mm)(standard hardware item-may b...
26578313006 Cord clamp
27A90003040125 Screw
28S51100400 Motor assembly (not shown)
3A19003050302 Screw (m5 x 30mm pan hd.)(4)(standard hardware ...
4511322000 Motor housing
5A18003050054 Set screw (m5 x 5mm)(2)(standard hardware item-...
6A95001050060 Set screw (m5 x 6mm)(2)(standard hardware item-...
7528312100 Brush roller (2)
8580302000 Switch
9A10003040307 Screw (m4 x 30mm pan hd.)(2)(standard hardware ...
0983000-471 Owners manual
0983000-471R Repair sheet