Home | Register Login | Wanted Manuals | MarketPlace | Members Area | Manuals Manufacturer Directory | UPC Lookup | Information Pages | Policy


Back To Craftsman Tractors-Riding-Lawnmowers       Model: 917.251572 or 917251572 Craftsman Lawn Tractor Garden Mower
Regular Text Search or Search by Model Number

Register / log-in to add to your Hammerwall Collection.
Manual Location


This is a partial text extraction from the pdf, to download the pdf, click the Manual tab. If you want to search this text, hold control and F, and type the word you are looking for.

Page: 1

SWA / RS ® MODEL NUMBER 917.251572 OWNER'SMANUAL o Assembly o Operation o Customer Responsibilities o Service and Adjustments o Repair Parts CAUTION : Read and follow all safety rules and instructions before operating this equipment . FOR CONSUMER ASSISTANCE HOT LINE , CALL THIS TOLL FREE NUMBER : 1 - 800 - 659 - 5917
Page: 2

SAFETY RULES _ b Safe Operation Practices for Ride - On Mowers & IMPORTANT : THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH 111 . CHILDREN t . GENERAL OPERATION • Read , understand , and follow aUinstructions in the manual Tragic accidents can occur ' if the operator is not alert to the and on the machine before starting . presence of children ° Children are often attracted to the • Only allow responsible adults , who are familiar with the machine and the mowing activity ° Never ' assume that instructions , to operate the machine . children will remain where you last saw them . • Clear the area of objects such as rocks , toys , wire , etc , • Keep children out of the mowing area and under the watchful which could be picked up and thrown by the blade . care of another responsible adult • Be sure the area is clear of other people before mowing . Stop • Be alert and turn machine off if children enter the area . r machine if anyone enters the area . • Before and when backing , look behind and down for small • Never carry passengers . children • Do not mow in reverse unless absolutely necessary . Always • Never carry children . They may fall off and be seriously look down and behind before and while backing injured or interfere with safe machine operation . ° Be aware of the mower discharge direction and do not point • Never allow children to operate the machine it at anyone _ Do not operate the mower without either the • Use extra care when approaching blind corners , shrubs , entire grass catcher or the guard in place . trees , or other objects that may obscure vision • Slow down before turning . • Never leave a running machine unattended Afways turn off IV . SERVICE blades , set parking brake , stop engine , and remove keys • Use extra care inhandUng gasoline and other fuels They are before dismounting . flammable and vapors are explosive • Turn off blades when not mowing . Use only an approved container • Stop engine before removing grass catcher or unclogging Never remove gas cap or add fuel with the engine chute _ running Allow engine to cool before refueling . Do not • Mow only in daylight or good artificial light smoke • Do not operate the machine while under the influence of Never refuel the machine indoors alcohol or drugs _ Never store the machine or fuel container inside where • Watch for traffic when operating near or crossing roadways there is an open flame , such as a water heater . • Use extra care when loading or unloading the machine into • Never run a machine inside a closed area . a trailer or truck • Keep nuts and bolts , especially blade attachment bolts , tight and keep equipment in good condition . II . SLOPE OPERATION • Never tamper with safety devices . Check their proper Slopes are a major factor related to loss - of - control and operation regularly _ tipover accidents , which can result in severe injury or death . • Keep machine free of grass , leaves , or other debris build - up . All slopes require extra caution . If you cannot back up the Clean oil or fuel spillage . Allow machine to cool before storing . slope or if you feel uneasy on it , do not mow it . = Stop and inspect the equipment if you strike an object . DO : Repair , if necessary , before restarting . • Mow up and down slopes , not across . • Never make adjustments or repairs with the engine running . • Remove obstacles such as rocks , tree limbs , etco - Grass catcher components are subject towear , damage , and • Watch for holes , ruts , or bumps Uneven terrain could deterioration , which could expose moving parts or allownd overturn the machine . Tall grass can hide obstacles . objects to be thrown . Frequently check components a • Use slow speed . Choose a low gear so that you wilt not have replace with manufacturer's recommended parts , when nec - to stop or shift whlle on the slope . essary • Follow the manufacturer's recommendations for wheel Mower blades are sharp and can cut Wrap the blade ( s ) or weights or counterweights to improve stability wear gloves , and use extra caution when servicing them • Use extra care with grass catchers or other attachments . Check brake operation frequently Adjust and service as These can change the stability of the machine . required . • Keep all movement on the sfopes slowand gradual Do not make sudden changes in speed or direction _ tant safety precautions . It meansor - • Avoid starting or stopping on a slope . If tires lose traction , Look for this symbol to point out YimpOUR CAUTIONH ! BECOME ALERT ! H disengage the blades and proceed slowly straight down the SAFETY IS INVOLVED . slope . H H = = = i = iHi H , HHHH = DO NOT : CAUTION : Always disconnect spark plug • Do not turn on slopes unless necessary , and then , turn slowly wire and place wire where it cannot contact and gradually downhill , ifpossible . spark plug in order to prevent accidental • Do not mow near drop - offs , ditches , or embankments . The & starting when setting up , transporting , mower could suddenly turn over if a wheel is over the edge of a cliff or ditch , or if an edge caves in . adjusting or making repairs , • Do not mow on wet grass . Reduced traction could cause , HHHHHH = , sliding • , LWARNING A • Do not try to stabilize the machine by putting your foot on the ground The engine exhaust from this product con - • Do not use grass catcher on steep slopes . tains chemicals known to the State of Califor - nia to cause cancer , birth defects , or other reproductive harm . HH = = H = 2
Page: 3

PRODUCT SPECIFICATIONS CONGRATULATIONS on your purchase of a Sears Tractor . It has been designed , engineered and manufac - HORSEPOWER : 25.0 tured to give you the best possibte dependability and performance . GASOLINE CAPACITY 3 5 GALLONS AND TYPE : UNLEADED REGULAR Should you experience any problem you cannot easily remedy , please contact your nearest Sears Authorized OIL TYPE ( APFSF / SG ) : SAE 10W30 ( above 32 ° F ) Service CentedDepartment Department . We have com - SAE 5W - 30 ( below 32 ° F ) petent , wel ! - trained technicians and the proper tools to OIL CAPACITY : W / FILTER : 4 2 PINTS service or repair this tractor . WiO FILTER : 3.7 PINTS Please read and retain this manual The instructions wilt enable you to assemble and maintain your tractor properiy SPARK PLUG : CHAMPION RC12YC Always observe the " SAFETY RULES " . GAP : . 030 " ) VALVE CLEARANCE : NOT ADJUSTABLE MODEL NUMBER 917251572 GROUND SPEED ( MPH ) : FORWARD : O - 5 8 REVERSE : 0 - 21 SERIAL NUMBER TIRE PRESSURE : FRONT : 14 PSI REAR : 10 PSI DATEOFPURCHASE BATTERY : AMP / HR : 40 THE MODEL AND SERIAL NUMBERS WILL BE FOUND MIN CCA : 340 ON A PLATE UNDER TIdE SEAT , CASE SIZE : UtR YOUSHOULDRECORDBOTHSERfALNUMBERAND CHARGING SYSTEM ; 15 AMPS @ 3600 RPM DATE OFPURCHASEAND KEEPIN A SAFE PLACE BLADE BOLT TORQUE : 30 - 35 FT LBS = OR FUTURE REFERENCE . WARNING : This tractor is equipped with an internal MAINTENANCE AGREEMENT combustion engine and should not be used on or near any unimproved forest - covered , brush - covered or grass - cov - A Sears Maintenance Agreement is available on this prod - ered land unless the engine's exhaust system is equipped uct . Contact your nearest Sears store for details . with a spark arrester meeting applicable local or state laws ( if any ) If a spark arrester is used , it should be maintained CUSTOMER RESPONSIBILITIES in effective working order by the operator , • Read and observe the safety rules . In the state of California the above is required by law ( Section 4442 of the California Public Resources Code ) ° , Foflow a regutar schedule in maintaining , caring for and using your tractor . . Otherstates may have similar laws Federal laws apply on federal lands . A spark arrester for the muffler is available , Follow the instructions under " Customer Responsibili - through your nearest Sears Authorized Service Center / ties " and " Storage " sections of this owner's manual Department ( See REPAIR PARTS section of this manual ) . , . . . . . . . . . . . . . . . . . . . . . . . . . . , i i , . _ , H , , J , J , = . , , IT " H . . i = il I , LIMITED TWO YEAR WARRANTY ON CRAFTSMAN RIDING EQUIPMENT For two ( 2 ) years from the date of purchase , if this Craftsman Riding Equipment is maintained , lubricated and tuned up according to the instructions in the owner's manual , Sears will i'epair or replace , free of charge , any parts found to be defective in material or workmanship This Warranty does not cover : " Expendable items which become worn during normal use , such as blades , spark plugs , air cleaners , belts , etc • Tire replacement or repair caused by punctures from outside objects , such as nails , thorns , stumps , or glass - Repairs necessary because of operator abuse , negligence , improper storage or accident or the failure to maintain the equipment according to the instructions contained in the owner's manual • Riding equipment used for commercial or rental purposes LIMITED 90 DAY WARRANTY ON BATTERY For ninety ( 90 ) days from date of purchase , if any battery included with this riding equipment proves defective in material or workmanship and our testing determines the battery wiiFnot hotd a charge , Sears wilt replace the battery at no charge IN - HOME WARRANTY SERVICE ON YOUR CRAFTSMAN RIDING EQUIPMENT IS AVAILABLE AT NO - CHARGE FOR 30 DAYS FROM THE DATE OF PURCHASE PLEASE CONTACT YOUR NEAREST SERVICE CENTER . AFTER 30 DAYS FROM THE DATE OF PURCHASE , WARRANTY SERVICE IS AVAILABLE BY TAKING YOUR CRAFTSMAN RIDING EQUIP - MENT TO YOUR NEAREST SEARS SERVICE CENTER . ( IN - HOME WARRANTY SERVICE WILL STILL BE AVAILABLE AFTER 30 DAYS FROM THE DATE OF PURCHASE BUT A STANDARD TRIP CHARGE WiLL APPLY ) THIS WARRANTY APPLIES ONLY WHILE THiS PRODUCT iS IN THE UNITED STATES This Warranty gives you specific legal rights , and you may afso have other rights which may vary from state to state SEARS , ROEBUCK AND CO . , D / 817 WA , HOFFMAN ESTATES , tL 60179 . . . . . . . . . . . . . . . . . . , , , , , = r , , , i , , , n . . . . . . . . . . . . . . . . . = = . . . . . _ , _ , _ _ 3
Page: 4

TABLE OF CONTENTS SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 MAINTENANCE SCHEDULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 PRODUCT SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SERVICE AND ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 - 27 CUSTOMER RESPONSIBILITIES . . . . . . . . . . . . . . . . . . . . . 3 , 17 - 20 STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 TROUBLESHOOTING , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 - 30 TRACTOR ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 REPAIR PARTS - TRACTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 - 49 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 10 REPAIR PARTS - ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 - 57 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 16 PARTS ORDERINGISERVIOE . . . . . . . . . . . . . . . BACK COVER aNDEX A Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . 1 . . - . . 16 Electrical : Accessories . . . . . . . . . . . . . . . . . . . . . . . . 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating Mower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Interlocks and Relays . . . . . . . . . . . . . . . . . . . . . . 2631 Adjustments : Options : Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . 3 . Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Carburetor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Spark Arrester . . . . . . . . . . . . . . . . 3 . , 4.0 . . . . . . . . . . . . . Engine : Clutch Pulley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . 3 Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Gauge Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 P Air Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Mower Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Front - To - Back . . . . . . . . . . . . . . . . . . . . . . . . 22 Cooling Fins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Parts Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Side - To - Side . . . . . . . . . . . . . . . . . . . . . . . . . . . 2t Oil Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Oil Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Throttle Control Cable . . . . . . . . . . . . . . . . . . 27 Parts , Replacement / Repair . . . . . . . . . . . 32 - 49 Oil Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15,19 Air Filter , Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Air Screen , Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8 Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 - 57 R Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 . . - 10 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 - 49 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 B F S Battery : Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Filter : Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Starting with Weak Battery . . . . . . . . . . 25 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Service and Adjustments . . . . . . . . . . . . . . . 21 - 27 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Carburetor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Fuel : Clutch Pulley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Belt : Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . 6 Motion Drive Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Hood Removal / Installation . . . . . . . . . . . 26 Removal / Replacement . . . . . . . . . . . . . 24 Motion Drive Belt Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Mower Dd ce Removal ! Replacement . . . . . . . . . . . 22 Removal / Replacement . . . . . . . . . . . . 22 Mower Drive Belt H Mower Blade Drive Removal / Replacement . . . . . . . . . . . . . . 22 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Removal / Replacement . . . . . . . . . . . . . 23 Mower Blade Drive Belt Blade : Hood RemovaVInstallation . . . . . . . . . . . . . . . . . . . . . 26 Removal / Replacement . . . . . . . . . . . . . 23 Sharpening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Mower Adjustment Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Front4o - Back . . . . . . . . . . . . . . . . . . . . . . . . 22 Side - to - Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . 1 Brake Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 LevelingMower Deck . . . . . . . . . . . . . . . . . . . . . . . . . 22 Mower Remova ! / Installation . . . . . . . . . . 21 Lubrication : Tire Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8,16,25 C Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Slope Guide Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Carburetor Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . t 9 Spark Plug ( s ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Clutch Pulley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 M . : Specifications . . . . . . . . . . . . . . . . . . . . . . 3 . . . . . . . . . . . . . . . . . . . Controls , Tractor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Maintenance Schedule . Z : . . : ii _ . ; ; . . . . . . . . . . 17 Starting the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 15 - 16 Customer Responsibilities . . . . . . . . . . . . . . . 17 - 20 Mower : Steering Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7,24 Engine : Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Adjustment , Front - tooBack . . . . . . . . . 22 Stopping the Tractor . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Air Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.9 Adjustment , Side4mSide . . . . . . . . . . . . . . . 21 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Cooling Fins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Blade Replacement . . . . . . . _ . . . . . . . . . . . . . . . . . t 8 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15,19 Blade Sharpening . . . . . . . . . . . . . . . . . . . . . . . 18 T Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Cutting Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Throttle Control Cable Adjustment . . . . . . 27 tnstaflation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Spark Plug ( s ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Tractor : Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8,18,25 Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ; . . . . . . 21 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 . . 8 . . Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . 2 . 9 - 30 Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mowing Tips . . . . . . . . . . . . . . . . . . . . . . 1.6 . . . . . . . . . . . . . . . . . . Transaxte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Lubrication Chart . . . . . . . . . . . . . . . . . . . . . . . 17 Muffler . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0 . . . . . . . . . . . . . . . . . . . . . . . Maintenance Schedule . . . . . . . . . . . . 17 Spark Arrester . . . . . . . . . . . . . . . . . . . . . . . . . . . 3,40 W Tire Care . . . . . . . . . . . . . . . . . . . . . . . . . . 8,18,25.1 . . 9 Transaxle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 0 Cutting Height , Mower . . . . . . . . . . . . . . . . . . . . . . . . . . ! 3 Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 . . 2 Oil : Wiring Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Cold Weather Conditions . . . . . . . . 15,19 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 4
Page: 5

ACCESSORIES AN ATTACH aENTS These accessories and attachments were available through most Sears retail outlets and service centers when the tractor was purchased Most Sears stores can order these items for you when you provide the model number of your tractor . ENGINE MAINTENANCE SPARK PLUG GAS CAN ENGINE OIL FUEL STABILIZER A1R FILTER BLADES BELTS , I PERFORMANCE Sears offers a wide variety of attachments that fit your tractor Many of these are listed below with brief explanations of how they can help you . This list was current at the time of publication ; however , it may change in future years - more attachments may be added , changes may be made in these attachments , or some may no longer be available or fit your model Contact your nearest Sears store for the accessories and attachments that are available for your tractor _ Most of these attachments do not require additional hitches or conversion kits ( those that do are indicated ) and are designed for easy attaching and detaching . AERATOR promotes deep root growth for a healthy lawn Tapered SLEEVE CULXIVATOR is 43 inches wide . Prepares ground for 2 5 - inch steel spikes mounted on lO - inch diameter discs puncture seeding , helps weed control Steel frame holds 5 adjustable sweeps . holes in soil at c ! ose intervais to let moisture soak in Steelweight tray Adjusts vertically , horizontally ( Requires sleeve hitch ) Optional for increased penetration accessory : steel furrow opener for wider openings for potatoes , corn , and other deep - seeded crops BUMPER protects front end of tractor from damage SLEEVE HITCH for use with master lift system Single pin couples / CARTS make hauling easy Variety of sizes available , plus accesso - uncouples ties such as side panelkits , tool caddy , cart cover , protective mat and dolly . SNOWTHROWER has 42 - inch swath Drum - type auger handles powdery and wet / heavy snow Mounts easily with simple pin arrange - CORING AERATOR takes small plugs out of soi _ to allow moisture ment . Discharge chute adjusts lrom tractor seat 6 - inch diameter and nutrients to reach grass roots 36 - inchswath 24 hardened steel spout discharges snow 10 to 50 feet Lift controlled at tractor seat coring tips 150 Ib capacity weight tray ( Use with chains and wheel weights and / or rear drawbar weight . ) DISC HARROW has 2 gangs of 4 sfeel blades that angle from 10 to SPRAYERS use 12 - volt DC eleclric motor that connects to the tractor 20 degrees , 40 inches wide Can hook 2 units in tandem . ( Requires battery or other 12 _ volt source Includes booms for automatic sleeve hitch ) spraying and hand held wand for spot spraying Wand has adiustabfe DOZER BLADE removes snow ; grades dirt , sand and gravel 48 spray pattern . For applying herbicides , insecticides , fungicides and inches wide , 17incheshigh , clears 44finch path when angled Master liquid fertilizers lift control lever for operator ease Spring trip for snow removal on SPREADER / SEEDERS make seeding , fertilizing , and weed killing uneven pavement ; built - in float for blade to follow ground contour . easy Broadcast spreaders are also usetul for granular de - icers and Reversible , replaceable scraper bar ( Use with tire chains and wheet sand weights and ! or rear drawbar weight ) SWEEPERS let you collect grass clippings and teaves EASY OIL DRAIN VALVE makes oil changes easier , faster FRONT NOSE ROLLER canters in front of mower deck to reduce TILLER has 8 hp engine to prepare seed beds , cultivate , and compost garden residue Chain - drivetransmission Six11 - inchdiamelerone chances of " scalping " on uneven terrain piece heat - treated steel tines . Tills 30 - inch path ( Requires sleeve GANG HITCH lets you tow 2 or 3 pull - behind attachments at hitch ) Or use 5 hp tow - behind TILLER with 36qnch swath to prepare once , such as sweepers , dethatchers , aerators ( not for use with seed beds , cultivate and compost garden residue . Tiller has its own rollers , carts or other heavy attachments ) built - in lift and depth control system and does NOT require a sleeve MULCH RAKE / DETHATCHER loosens soil and flips thatch and hilch Fits any lawn , yard or garden tractor . Simply hook up to the matted leaves to lawn surface for easy pickup . Twenty spring fine tractor drawbar and go ! Optional accessories for 5 hp tiller convert teeth Useful to prepare bare areas for seeding . Available for front Gor unit for dethatching , aerating , hilling without tools rear mounting . HIGH PERFORMANCE REEL - ACTION SPRIN TIRE CHAINS are heavy duty ; closely spaced extra - large cross links TIN E DETHATCHER covers 36 - inch wide path and tosses thatchinto give smooth ride , outslanding traction large hopper Mounts behind tractor TRACTOR CAB has heavy duty vinyl fabric over tubular steel frame , PLOW turns soil 6 inches deep , cuts 10 - inch furrow Crank adjust - ABS plastic top ; clear plastic windshield offers 360 degree visibility ment controls depth , 3 - posilion yoke sets width Heavy steel landside Hinged metal doors with catch Keeps operator warm and dry for straight furrowing ( Requires sleeve hitch . ) Remove vinyl sides and windshields for use as sun protector in RAMP TOPS AND FEET let you load and unload tractor from a summer . Optional accessories include : tinted / tempered solid pickup truck Use with 2 x 8 or 2 x 10 lumber safety glass windshield with hand operated wiper ; 12 - volt amber caution Hght for mounting on cab top REAR GRADER BLADE is 42 incheswide and operated from driver's seat Reversible steel blade can be angled at 30 degrees for grading VACS for powerful collection of heavy grass clippings and leaves Reverses for pushing snow backwards ( Requires sleeve hitch ) Optional wand attachment to pick up debris in hard - to - reach places ROLLER for smoother lawn surface . 36 - inch wide , 18 - inch diameter VAC / CHIPPER includes a chipper - shredder water - tight drum holds up to 390 Ibs of weight . Rounded edges WEIGHT BRACKET for drawbar for snow removal applications . Can prevent harm to turf Adjustable scraper automatically cteans drum be mounted on front of fractor for plowing applications Uses ( 1 ) 55 Ib weight WHEEL WEIGHTS for rear wheels provide needed traction for snow removal or dozing heavy materials 5
Page: 6

u H i CONTENTS OF HARDWARE PACK L i Parts Bag contents shown full size Parts packed separately in carton ( 1 ) Shoulder Bolt 5 / 16 - 18 ( 1 ) Knob Seat Video | Cassette ( 1 ) Washer 17 / 32 x 1 - 3 / t6 x 12 Gauge Steering Wheel ner Springs ( single loop ) i - - Manual ( 4 ) Retainer Springs = r - q Parts bag contents not shown full size = _ / f - _ \ , _ ( 2 ) Washe3rs / 8 , Bolts \ _ . / / y ( 2 ) Gauge z _ . ( 2 ) Center - \ _ Wheels _ lock Nuts ( 2 ) Washers 17 / 32 x 7 / 8 x 16 Ga , _ ( 2 ) Front Link Assemblies : _ @ Nose Roller Steering Wheel insert ( 2 ) Hex Bolts 3 / 8 - 16 x t ( 2 ) Nylon Locknuts 3 / 8 - 16 Brackets ( 2 ) Hex Bolts 1 / 4 - 20 x 3 / 4 @ ( 2 ) Hex Nuts t / 4 - 20 ( 2 ) Keys 9 / 32 x 5 / 8 x 16 Gauge ( 2 ) Washers Steering Slope Sheet Sleeve • ( 2 ) Lock Washers 1 / 4 , , , , d 6
Page: 7

i . . . . . i . , Hi , , N _ 1II ASS LY Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes . To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely . . Use the correct tools as necessary to insure proper tightness . TOOLS REQUIRED FOR ASSEIVlBLY A socket wrench set will make assembly easier . Standard wrench sizes are listed . ( 2 ) 7 / 16 " wrenches Tire pressure gauge ( 1 ) 1 / 2 " wrench Utility knife ( 2 ) 9 / 16 " wrenches ( 1 ) 3 / 4 " wrench ( 1 ) 3 / 4 " socket with drive ratchet When right or left hand is mentioned in this manual , it means when you are in the operating position ( seated behind the steering wheel ) _ TO REMOVE TRACTOR FROM CARTON UNPACK CARTON o Remove all accessible loose parts and parts cartons from carton ( See page 6 ) . o Cut , from top to bottom , along lines on all four comers of carton , and lay panels flaL , Check for any additional loose parts or cartons and remove . BEFORE ROLLING TRACTOR OFF SKID ATTACH STEERING WHEEL ( See Fig . 1 ) FIG , 1 - Remove hex bolt , lock washer and large flat washer from steering shafL o Position front wheels of the tractor so they are pointing TO ROLL TRACTOR OFF SKID ( See Opera - straight forward , tion section for location and function of con - o Slide the steering sleeve over the steering shafl _ trols ) ° Position steering wheel so cross bars are horizontal = Press liftlever plunger and raise attachment lift lever to ( left to right ) and slide onto steering wheel adapter . its highest position . * Secure steering wheel to steering shaft with hex bolt , = Release parking brake by depressing clutch / brake lock washer and large flat washer previously removed . pedal Tighten securely . o Snap steering wheel insert into center of steering " disengafrgeeePw'ahceeeltransmissioi _ nfCre ° , n , _ trw ° l _ leTeRli _ l _ lPl _ tl _ ° _ , tin ° wheel the Operation section of this manual ) . o Remove protective plastic from tractor hood and grill o Roll tractor forward off skid . IMPORTANT : CHECK FOR AND REMOVEANY OSTAPLESR IN SKID THAT MAY PUNCTURE TIRES WHERE TRACT . Remove mower and packing materials . IS TO ROLL OFF SKID . • Remove ties from V - belts .
Page: 8

i Ul , , , ii , i , , , i i , , i i , , i u , , ii i , ii , , , lUl ii , , lllllllll , lllllll LY H _ INSTALL SEAT ( See Fig . 3 ) CONNECT BATTERY ( See Fig . 2 ) Adjust seat before tightening adjustment knob . Remove cardboard packing on seat pan , nals . Before connecting battery , re - • Place seat on seat pan and assemble shoulder bolt . move metal bracelets , wristwatch CAUTION : Do not short battery termi - bands , rings , etc _ = Assemble adjustment knob and fiat washer loosely , , Do not tighten , Positive terminal must be connected ° Tighten shoulder bolt securely , first to prevent sparking from acciden - tal grounding . • Lower seat into operating position and sit on seat ° • Sfide seat until a comfortable position is reached which • Lift hood to raised position , allows you to press clutch / brake pedat all the way down . o Open terminal access doors , remove terminal protec - tive caps and discard , . Get off seat without moving its adjusted position . = If this battery is put into service after month and year • Raise seat and tighten adjustment knob securely , indicated on label ( label located between terminals ) charge battery for minimum of one hour at 6 - t0 amps . SEAT = First connect RED battery cable to positive ( + ) battery terminal with hex bolt , flat washer , lock washer and hex nut as shown Tighten securely o Connect BLACK grounding cable to negative ( - ) bat - SHOULDER _ _ \ \ r'T " ' _ \ ' \ \ \ tery terminal with remaining hex bolt , fiat washer , lock washer and hex nut ° Tighten securely . ° Close terminal access doors , , Use terminal access doors for : o Inspection for secure connections ( to tighten hard - ware ) . - Inspection for corrosion . - Testing battery , , ADJUSTMENT KNOB • Jumping ( if required ) _ FIG . 3 Periodic charging , LOCK FLAT HEX NUT WASHER WASHER TO ATTACH NOSE ROLLER ( See Fig . 4 ) DISCARD TERMINAL HEX , " • Position brackets , 17 / 32 x 7 / 8 x 16 gauge washers , and _ ROTECTIVE CAPS BOLT nose rolter between deck mounting brackets as shown . Be sure to position brackets on correct side , as shown ° • Install 3 / 8 - 16 x 1 hex bolts and 3 / 8 - 16 crownlock nuts as shown _ Tighten hardware securely . NOTE : Be sure bracket tabs are positioned in tab holes in deck brackets . POSITIVE ( RED ) " B " BRACKETTAB CABLE , I NEGATIVE ( BLACK ) CABLE HEX FIG . 2 " A " CROWNLOCK BRACKET NUT TAB WASHER FIG . 4
Page: 9

, , n , = , H , , i = , = . = . . = . . . i . . . . . . . . . , , H , = , = = , ' " = = . . . . . . . . . . , , nu , n , = ASS LY . . . . , , , , , , nu , , , = , , , , n , , u , i , r , , , , i 1 , , , , , , r , r , , , , u , , , , , . . . . . . . . . . . . . . . . . . . . . . . . . INSTALL MOWER AND DRIVE BELT ° Connect anti - sway bar to chassis bracket under left footrest and retain with double loop retainer spring ° ( See Figs . 5 and 6 ) Turn height adjustment knob clockwise to remove Be sure tractor is on level surface and mower suspension ° slack from mower suspension , arms are raised with attachment lift control , Engage park - Raise deck to highest position , ing brake . ° • Cut and remove ties securing anti - sway bar and belts ° ° Assemble gauge wheel bars to brackets using clevis Swing anti - sway bar to left side of mower deck , pins and double loop retainer springs Assemble gauge wheels as shown using long shoulder o Slide mower under tractor with discharge guard to right ° side of tractor , . bolts , 3 / 8 washers , and 3 / 8 - 16 center locknuts . Tighten securely , IMPORTANT : CHECK BELT FOR PROPER ROUTING TINO ALL MOWER PULLEY GROOVES . INSTALL BELT IN - Adjust gauge wheels before operating mower as shown ELECTRIC CLUTCH PULLEY GROOVE in the Operation section of this manual . ° Install one front link in top hole of the L , H . front mower CHECK MOWER LEVELNESS bracket and L . H front suspension bracket . , Retain with two single loop retainer springs as shown . For best cutting results , mower should be properly leveled . See " TO LEVEL MOWER HOUSING " in the Service and , Install second front link in RH front suspension bracket only and retain with single loop retainer spring as Adjustments section of this manual ° shown CHECK FOR PROPER POSITION OF ALL , , Slide right side of mower back and install link in top hole BELTS of R , H . front mower brackeL Retain with single loop retainer spring as shown _ See the figures that are shown for replacing motion , mower - Turn height adjustment knob counterclockwise until it drive , and mower blade drive belts in the Service and stops , , Adjustments section of this manual , Verifythat the belts are routed correctly FRONT • Lower mower linkage with attachment lift control SUSPENSION . Place the suspension arms on inward pointing deck BRACKETS pins ° If necessary , rock and raise front of mower to align deck pins with the holes in suspension arms , FRONT Retain with double loop retainer springs LINKS SUSPENSION ELECTRIC CHASSIS DOUBLE LOOP ARMS CLUTCH BRAC ET ANTI - SWAY RETAINER SPRING PULLEY DOUBLE LOOP BAR ( inward pointing deck RETAINER pins ) SHOULDER SPRING BOLT Loll , GAUGE WHEEL BAR ! SINGLE LOOP RETAINER SPRINGS GAUGE WHEEL FRONT MOWER 318 BRACKET 3t8 - 16 WASHER CENTER LOCKNUT DISCHARGE GUARD CLEVIS PINS IDLER LOOP RETAINER SPRINGS FIG . 5
Page: 10

BLY i i CHECK TIRE PRESSURE / CHECKLIST The tires on your tractor were ovednflated at the factory for BEFORE YOU OPERATE AND ENJOY YOUR NEW shipping purposes _ Correct tire pressure is important for TRACTOR , WE WISH TO ASSURE THAT YOU ORECEIVEM best cutting performance . THE BEST PERFORMANCE AND SA TISFA CTION FR THIS QUALITY PRODUCT • Reduce tire pressure to PSI shown in " PRODUCT SPECIFICATIONS " on page 3 of this manual PLEASE REVIEW THE FOLLOWING CHECKLIST : _ " All assembly instructions have been completed . . CHECK BRAKE SYSTEM v " No remaining loose parts in carton . After you learn how to operate your tractor , check to see that the brake is properly adjusted . See " TO ADJUST , / Battery is properly prepared and charged . ( Minimum 1 hour at 6 amps ) . . BRAKE " in the Service and Adjustments section of this manual ° , / Seat is adjusted comfortably and tightened securely . , / NI tires are properly inflated . ( For shipping purposes , the tires were overinflated at the factory ) . # ' Be sure mower deck is propedy leveled side - to - side / front - to - rear for best cutting results . ( Tires must be properly inflated for leveling ) . . , / Check mower and drive belts . Be sure they are routed properly around pulleys and inside all belt keepers . , / Check wiring . See that all connections are still secure and wires are properly clamped ° , / Before driving tractor , be sure freewheel control is in drive position ° WHILE LEARNING HOW TO USE YOUR TRACTOR , PAY EXTRA ATTENTION TO THE FOLLOWING IMPORTANT ITEMS : • / Engine oil is at proper level , / Fuel tank is filled with fresh , clean , regular unleaded gasoline . , / Become familiar with all controls - their location and function . Operate them before you start the engine . . J Be sure brake system is in safe operating condition . , / tt is important to purge the transmission before operat . . ing your tractor for the first time . Follow proper starting and transmission purging instructions ( See " TO START ENGINE " and ' PURGE TRANSMISSION in the Op - eration section of this manual ) . 10
Page: 11

. . . . . . . . . ii1 , , 11 , , , iu i irlr i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OPERATUON . . . . . . . . . . . . n fill I ' Ull . . . . . . . . . . . . . . . . . . . nll , i iiii1 , 111 These symbols may appear on your tractor or in literature supplied with the product . Learn and understand their meaning , FORWARD FAST SLOW BATTERY CAUTION OR REVERSE WARNING ENGINE OFF OILPRESSURE CLUTCH LIGHTS ON LIGHTS OFF ENGINE ON MOWER HEIGHT DIFFERENTIAL PARKING BRAKE UNLOCKED FUEL CHOKE LOCK LOCKED REVERSE NEUTRAL HIGH LOW PARKING BRAKE MOWER LIFT ATTACHMENT ATTACHMENT IGNITION CLUTCH ENGAGED CLUTCH DISENGAGED HYDROSTATIC FREE WHEEL DANGER , KEEP HANDS AND FEET AWAY ( Hydro Models only ) 1I
Page: 12

. . . . . . . . . . . . . . . . . . . . . . . . . . ii . i . i , i . i . i i . . 11 . . = = 1 = = . . ! . . . r . I ' ' H ' , HI OPERATION ii iiiiiii . I . IIIII , H , I , I , i . . . , HI iii1 . i , . iiHm , ii ii , i . 111 KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR . Compale the illustratfonswith you rtractor to familiarize yourself with the location of Various controls and adjustments ° Save this manual for future reference _ THROTTLE CONTROL AMMETER ATTACHMENT LIFT LEVER CLUTCH SWITCH . UNGER CHOKECONTROL HOUR METER LIGHT SWITCH CLUTCHtBRAKE ATTACHMENT PEDAL LIFT LEVER IGNITION SWITCH HEIGHTADJUSTMENT KNOB PARKING BRAKE LEVER MOTION CONTROL LEVER SPEEDS : / FREE WHEEL CONTROL FIG . 6 Our tractors conform to the safety standards of the American National Standards Institute , THROTTLE CONTROL _ Used to control engine speed , ATTACHMENT CLUTCH SWITCH - Used to engage mower blades or other attachments mounted to your tractor ° FREEWHEEL CONTROL - Disengages transmission for pushing or slowly towing the tractor with the engine off , , ATTACHMENT LIFT LEVER - Used to raise and lower the mower ' deck or other attachments mounted to your tractor _ IGNITION SWITCH - Used to start and stop the engine ° CLUTCHIBRAKE PEDAL - Used for declutching and AMMETER - Indicates battery charging ( + ) or discharging braking the tractor and starting the engine . , ( - ) . MOTION CONTROL LEVER - Selects the speed and PARKING BRAKE LEVER - Locks clutch / bi " ake pedal into direction of tractor . the brake position _ CHOKE CONTROL - Used when starting a cold engine , HEIGHT ADJUSTMENT KNOB _ Used to adjust the mower HOURMETER - Indicates hours of operation . height ° LIGHT SWITCH - Turns the headlights on and off ° 12
Page: 13

OPERATION . . . . . . . . . . . . , , m , = . The operation of any tractor can result in foreign objects thrown into the eyes , which can result in severe eye damage . Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs . We recommend a wide vision safety mask over the i spectacles or standard safety glasses . , = , N , , , = , , , , , , , = ' = = . . . . . . . , , , , . , . . . . . . . . . . . . . . . . . . . . . HOW TO USE YOUR TRACTOR NOTE : Under certain conditions when unit is standing idle with the engine running , hot engine exhaust gases may TO SET PARKING BRAKE ( See Fig . 7 ) cause " browning " of grass . To eliminate this possibility , always stop engine when stopping tractor on grass areas . Your tractor is equipped with an operator presence sensing switch . When engine is running , any attempt by the _ stop tractor com - operator to leave the seat without first setting the parking _ _ letpely , as described above , before leav - brake will shut off the engine . = Depress clutch / brake pedal into full " BRAKE " position J _ , _ o _ rator _ position ; to empty and hold . _ cher _ etc _ • Place parking brake tever in " ENGAGED " position and release pressure from clutch / brake pedal . . Pedal should TO USE CHOKE CONTROL ( See Fig . 7 ) remain in " BRAKE " position _ Make sure parking brake witl hold tractor secure . Use choke control whenever you are starting a cold engine . Do not use to start a warm engine PUSH IN TO ATTACHMENT CLUTCH ° To engage choke control , pull knob ouL Slowly push THROTTLE " DISENGAGE " SWITCH PULL OUT TO knob in to disengage CONTROL LEVER " ENGAGE ' TO USE THROTTLE CONTROL ( See Fig , 7 ) CHOKE Always operate engine at full throttle . CONTROL , Operating engine at less than full throttle reduces the battery charging rate CLUTCH / BRAKE - Full throttle offers the best bagging and mower perfor - PEDAL " BRAKE " mance POSITION IGNITION TO iVlOVE FORWARD AND BACKWARD ( See Fig . 7 ) The direction and speed of movement is controlled by the motion control [ ever . MOTION ° Start tractor with motion control lever in neutral ( N ) CONTROL LEVER position . . • Release parking brake and clutch / brake pedal HEIGHT " DRIVE " ADJUSTMENT PARKING ° Slowly move motion control lever to desired position . POSITION KNOB BRAKE " DISENGAGED . . . . ENGAGED " TO ADJUST MOWER CUTTING HEIGHT ( See POSITION POSITION Fig . 7 ) FIG . 7 The cutting height is controlled by turning the height adjust - STOPPING ( See Fig . 7 ) ment knob in desired direction ° MOWER BLADES ° Turn knob clockwise ( f " _ ) to raise cutting height . ° Move attachment clutch switch to " DISENGAGED " , Turn knob counterclockwise ( V _ , ) to tower cutting position _ height GROUND DRIVE - The cutting height range is approximately 1 - 1 / 2 " to 4 - 1 / 2 " . • Depress clutch / brake pedal into full " BRAKE " position The heights are measured from the ground to the blade tip o Move motion control lever to neutral ( N ) position . with the engine not running . . These heights are approxi - IMPORTANT : THE MOTION CONTROL LEVER DOES mate and may vary depending upon soil conditions , height NOT RETURN TO NEUTRAL ( N ) POSITION WHEN THE of grass and types of grass being mowed . . CLUTCH / BRAKE PEDAL IS DEPRESSED . ENGINE - ° The average lawn should be cut to approximately 2 - 1 / 2 inches during the cool season and to over 3 inches = Move throttle control to slow ( , , _ . ) position during hot months For healthier and better looking NOTE : Failure to move throttle control to slow ( , _ ) lawns , mow often and after moderate growth position and allowing engine to idle before stopping may ° For best cutting performance , grass over 6 inches in cause engine to " backfire " . height should be mowed twice . Make the first cut , Turn ignition key to " OFF " position and remove key . relatively high ; the second to desired height . Always remove key when leaving tractor to prevent unauthorized use o Never use choke to stop engine 13
Page: 14

Hm , = 1 = OPERATION i TO OPERATE ON HILLS TO ADJUST GAUGE WHEELS ( See Fig , 8 ) Adjust gauge wheels with tractor on a fiat level surface _ _ rive - - _ p or'down i = Adjust mower to desired cutting height , i hills with slopes greater than 15 ° and I ° Lower mower with tift control . Remove rear retainer ! do not drive across _ any slope . I spring and clevis pin which secure each gauge wheel . o Choose the slowest speed before starting up or down o Lower gauge wheels to ground ° Raise gauge wheelsar hills . slightly to align holes in bracket and gauge wheel b o Avoid stopping or changing speed on hills . and insertclevis pins . Gauge wheels should be slightly off the ground ' • If slowing is necessary , move tt ] rottte control lever ' to slower position . . Replace retainer springs into clevis pins . ° If stopping is absolutely necessary , push clutch / brake _ edal quickly to brake position and engage parking RETAINER rake _ SPRING . Move motion control lever to neutral ( N ) position . IMPORTANT : THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL ( N ) POSITION WHEN THE GAUGE CLUTCH / BRAKE PEDAL IS DEPRESSED . WHEEL BAR • To restart movement , slowly release parking brake and clutch / brake pedal . Slowly move motion control lever to slowest setting . . Make all turns slowly GAUGE WHEEL ' TO TRANSPORT ( See Figs , 6 and 10 ) BRACKET When pushing or towing your tractor , be sure to disengage FIG . 8 ) transmission by placing freewheel control in freewheeling position . Free wheel control is located at the rear drawbar TO OPERATE MOWER ( See Figs . 6 and 7 ) of tractor ° Your tractor is equipped with an operator ' presence sens - ° Raise attachment lift to highest position with attach - ing switch . Any attempt by the operator to leave the seat ment lift control . with the engine running and the attachment clutch engaged . Remove retainer spring from freewheel control rod . will shut off the engine . o Push control rod in to disengage transmission andon - Select desired height of cut . reinsert retainer spring into control rod hole now • Lower mower ' with attachment lift control . back side of the bracket ° Start mower blades by engaging attachment clutch , Do not push or tow tractor at more than two ( 2 ) MPH . control . - To reengage transmission , reverse above procedure . . TO STOP MOWER BLADES - disengage attachment NOTE : To protect hood from damage when transporting clutch control . you r tractor on a truck or a traile r , be su re hood is closed and secured to tractor : . Use an appropriate means of tying hood CAUTION : Do not operate the mower I to tractor ( rope , cord , etc . ) . without either the entire grass catcher _ on mowers so equipped , or the dis - i charge guard in place . " ' RUNNER " DISCHARGE GUARD FIG , 9 14 FIG . 10
Page: 15

This engine on this product is designed for maximum CHECK ENGINE OIL LEVEL ( See Fig . 11 ) performance and life if operated with the choke ( l \ l ) fully open and the throttle control in the fast ( , _ ) position . To • The engine in your tractor has been shipped , from the open the choke fully requires an engine warm - up period of factory , already filled with summer weight oil several seconds to several minutes , depending on the • Check engine oil with tractor on level ground _ temperature ° • Unthread and remove oil fill cap / dipstick ; wipe oil off After starting the engine , first open the choke slowly until Reinsert the dipstick into the tube and rest oil fill cap on the engine just begins to run smoothly . . Then open the the tube . Do not thread the cap onto the tube . Remove choke in smal _ steps , allowing the engine to accept sma } i and read oil level If necessary , add oil until " FULL " changes in speed and load , until the choke is fully open . . mark on dipstick is reached . Do not overfill . During engine warm - up , the equipment can be operated = For cold weather operation you should change oil fore easier starting ( See " OIL V _ SCOSITY CHART ' in th When starting engine for the first time or if engine has run Customer Responsibilities section of this manual ) out of fuel , it will take extra cranking time to move fuel from , To change engine oil , see the Customer Responsibili - the tank to the engine . ties section in this manual , • Depress clutch / brake pedal and set parking brake . r • Place motion control lever in neutral ( N ) position . • Move attachment clutch to " DISENGAGED " position . . • Pull choke control out to choke ( N ) position for cold engine start . For warm engine start do not use choke control o Move throttle control to midway between fast ( , _ ) and slow ( , _ ) positions o Insert key into ignition and turn keyctockwiseto " START " position and release key as soon as engine starts . Do not run starter continuously for more than fifteen FIG . 11 seconds per minute , tf engine does not start after several attempts , move throttle control to fast ( , _ ) position , wait a few minutes and try again . ADD GASOLINE ° When engine starts , slowly push choke control in . . • Fil ! fuel tank . Use fresh , clean , regular unleaded gasoline with a minimum of 87 octane . . ( Use of leaded ° Move throttle control to fast ( , _ ) position _ gasoline will increase carbon and lead oxide deposits o Mow engine to warm up for a few minutes before and reduce valve rife ) . Do not mix oil with gasoline . engaging drive or attachments Purchase fuel in quantities that can be used within 30 days to assure fuel freshness IMPORTANT : COLD STARTING FOR HYDRO ( BELOWRE ( 40 ° F ) - AFTER STARTING ENGINE AND BEFOR IMPORTANT : WHEN OPERATING tN TEMPERATURES DRIVING , LET TRANSMISSION WARM UP FO 1 ) BELOW 32 ° F ( 0 ° C ) , USE FRESH , CLEAN WINTER GRADE MINUTE BY PLACING MOTION CONTROL LEVER IN GASOLINE TO HELP INSURE GOOD COLD WEATHER NEUTRAL AND RELEASING CLUTCH / BRAKE PEDAL STARTING . NOTE : If at a high altitude ( above 3000 feet ) or in cold WARNING : Experience indicates that alcohol blended temperatures ( below 32 ° F ) , the carburetor fuel mixture fuels ( called gasohol or using ethanol or methanol ) can may need to be adjusted for best engine performance . . See attract moisture which leads to separation and formation of " TO ADJUST CARBURETOR " in the Service and Adjust - acids during storage Acidic gas can damage the fuel ments section of this manual system of an engfne while in storage To avoid engine problems , the fuel system should be emptied before stor - age of 30 days or longer . Drain the gas tank , start the engine and let it run until the fuel lines and carburetor are empty . Use fresh fuel next season . See Storage Instruc - tions for additional information Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur . MI , , iH , , H filler neck . Do not overfill , Wipe off any spilled oil or fuel , Do not store , spill or ! _ CALITION : Fill to bottom of gas tank use gasoline near an open flame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hi I , H , 15
Page: 16

MOWING TiPS PURGE TRANSMISSION t , H = = ' H'H " ' H ' = = I ' I I = ' 1 = ' I ' I ' ' 11 " , 11 " • Tire chains cannot be used when the mower housing is attached to tractor freewheel lever while the engine is run - o Mower should be properly leveled for best mowing I _ CAUTION : Never engage or disengage ning , performance . See " TO LEVEL MOWER HOUSING " in the Service and Adjustments section of this manual To ensure proper operation and pedormance , it is recom - • Use the runner on the right hand side of mower as a mended that the transmission be purged before operating guide . The blade cuts approximately an inch outside tractor for the first time . This procedure will remove any the runner ( See Fig 9 ) . trapped air inside the transmission which may have devel - = The left hand side of mower should be used for ' trim - oped during shipping of your tractor . ming . IMPORTANT : SHOULD YOUR TRANSMISSION REQUIREIT o Drive so that clippings are discharged onto the areahe REMOVAL FOR SERVICE OR REPLACEMENT , that has been cut Have the cut area to the right of t SHOULD BE PURGED AFTER REINSTALLATION tractor . This wilt result in a more even distribution of BEFORE OPERATING THE TRACTOR . clippings and more uniform cutting - Place tractor safely on level surface with engine off and - When mowing large areas , start by turning to the right parking brake set , so that clippings will discharge away from shrubs , o Disengage transmission by placing freewheel control fences , driveways , etc . After one or two rounds , mow in freewheeling position ( See " TO TRANSPORT " in in the opposite direction making left hand turns until this section of manual ) . finished ( See Fig _ 12 ) o , Sitting in the tractor seat , start engine _ After the engine o If grass is extremely tail , it should be mowed twice top * is running , move throttle control to slow ( , _ ) position _ reduce load and possible fire hazard from dried cli With motion control lever in neutral ( N ) position , slowly pings . Make first cut relatively high ; the second to the disenqage clutch / brake pedal . desired height . = Move motion control lever to full forward position and • Do not mow grass when it is wet . Wet grass will plugto hold for ' five ( 5 ) seconds . Move lever to full reverse mower ' and leave undesirable clumps . Allow grass position and hold for five ( 5 ) seconds . Repeat this dry before mowing . procedure three ( 3 ) times . ° Always operate engine at full throttle when mowing itos - NOTE : During this procedure there will be no movement of assure better mowing performance and proper d drive wheels _ The air is being removed from hyd raulic drive charge of material Regulate ground speed by select - system ing a low enough gear to give the mower cutting performance as well as the quality of cut desired • Move motion control lever to neutral ( N ) position . Shut - off engine and set parking brake . ° When operating attachrnents , select a ground speed that will suit the terrain and give best performance of , Engage transmission by placing freewheel control in the attachment being used . driving position ( See " TO TRANSPORT " inthis section of manual ) . F • Sitting inthetractor seat , start engine . After the engine is running move throttle control to half ( 1 / 2 ) speed . With mot on contro lever in neutral ( N ) position , slowly disengage clutch / brake pedal . • Slowly move motion control lever forward , after the tractor moves approximately five ( 5 ) feet , slowly move motion control lever to reverse position , After the tractor moves approximately five ( 5 ) feet return the motion control lever to the neutral ( N ) position . Repeat this procedure with the motion control lever three ( 3 ) C times . ° Your tractor is now purged and now ready for normal operation _ FIG , 12 16
Page: 17

i , i , UlUllll , i , ii ilU iil , lrll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I iiii CUSTOMER RESPONSIBUUTIES . . . . . . . . . . . . . . . . . . . . . . . . i i i ii , ll ii , i i , iii " MAINTENANCE SCHEDULE / _ _ . - _ _ o _ _ . . . . . . . . . . . . . . . . . . . . FtLL iN DATES / _ _ , _ / _ + _ " _ REGULSAERRvlcE . . . . . . . . . . ATES Check Brake Operation 6 / _ # ' ! Check Tire Pressure 6 / 6 / T Check for Loose Fasteners 6 / - - _ - - _ 6 / 7 6 / R " Shar ; en / Replace Mower Blades 6 / ' 4 t ' Lubrication Chart 6 / I T Check Battery Level / Recharge 0 Clean Battery and Terminals 6 / 1 6 / a CheckTransaxie Cooling 6 / Adjust Blade Belt ( s ) Tension 6 # 15 Adjust Motion Diive Beit ( s ) Tension 6 / 5 Check Engine Oil Level " 6 # 4 ' ' 6 / . . . . ' . . . . . . . . . . . . " . . . . . . . . . _ = = = Change Engine Oil 6 / _ 1,2,3 6 / Clean Air Filter N Clean Air Screen . . . . . . . . . G inspect Muffler / Spark Arrester 6 / I Replace OilFilter ( ifequipped ) _ , 2 L J Clean Engine Cooling Fins i 6 / 2 i Replace Spark Ptug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 # 4 6 / . . . . . . . . . . . . . . Replace Air Filter Paper Cartridge _ _ _ _ 6 / 2 j ! Replace Fuel Filter ! 6 / , , , 1 - Change mare allen when operating under a heavy load er in high ambien _ temperalures 5 - g equipped wi _ hadjustable system 2 - Sen'ice more oflen when opmaling in dirly or dusty conditions 6 - No ] requi [ ed i : [ equipped with maintenance4ree battery 3 + I [ equipped with oil { flier , change oi _ ever , / 50 hours 7 + Tighten { runtaxle pivot boil to 35 I1 - _ bs maximum 4 + Replace b _ adesmore ellen when mowing in sandy soil Do not overtighten GENERAL RECOMMENDATIONS LUBRICATION CHART The warranty on this tractor does not cover items that have been subjected to operator abuse or negligence , . To ( _ ) TIE ROD BALL JOINTS receive full value from the warranty , operator must maintain tractor as instructed in this manual . . ( _ ) SPINDLEZERK f , q i _ _ _ / , - , , \ " _ SPtNDLEZERK ( _ ) Some adjustments will need to be made periodically to properly maintain your tractor ° ( _ ) FRONT WHEEL " _ _ . _ : _ : . , : ' _ FRONT WHEEL ( _ All adjustments in the Service and Adjustments section of . this manual should be checked at least once each season ® STEER , NG ? 1 % ' , Once a year you should replace the spark plug , clean SECTOR GEAR ENGINE ( _ ) or replace air filter , and check blades and belts for TEETH wear . . A new spark plug and clean air filter assure proper air - fuel mixture and help your engine run better and last longer . BEFORE EACH USE • Check engine oil level o Check brake operation . , Check tire pressure , Check for loose fasteners . ( _ ) SPRAY SILICONE LUBRICANT ( MOVE BOOTS TO LUBRICATE ) IMPORTANT : DO NOT OIL OR GREASE THE PIVOT POINTS ( _ ) GENERAL PURPOSE GREASE WHfCH HAVE SPECIAL NYLON BEARINGS VISCOUS LUBRi - CANTS W + LL ATTRACT DUST AND DIRT THAT WILL SHORTEN ® REFER TO CUSTOMER RESPONSIBILITIES ENGINE SECTION THE LiFE OF THE SELF - LUBRICATING BEARINGS . iF YOU FEEL THEY MUST BE LUBRICATED , USE ONLY A DRY , POW - DERED GRAPHITE TYPE LUBRICANT SPARINGLY 17
Page: 18

ii , , nnll ¸ I " i . . . . . . . . . . . . . . . . . . . . . ii RESPONSlBILITI CUSTOMER n ilnl , n nlnnl TRACTOR TO SHARPEN BLADE ( See Fig . 14 ) Care should be taken to keep the blade balanced . An Always observe safety rules when performing any mainte - unbalanced btade will cause excessive vibration and even - nance . tual damage to mower and engine _ BRAKE OPERATION • The blade can be sharpened with a file or on a grinding wheel Do not attempt to sharpen while on the mower . If tractor requhes more than six ( 6 ) feet stopping distance at high speed in highest gear , then brake must be adjusted . . To check blade balance , you will need a 5 / 8 " diameter steel bolt , pin , ora cone balancer . ( When using a cone ( See " TO ADJUST BRAKE " in the Service and Adjust - ments section of this manual ) . balancer , follow the instructions supplied with bal - ancer ) . TIRES , Stide blade on to an unth readed portion of the steel bolt . or pin and hold the bolt or pin parallel with the ground o Maintain proper air pressure in all tires ( See " PROD - " ' al If blade is balanced , it should remain in a horizontal UCT SPECIFICATIONS on page 3 of this manu ) . position . If either end of the blade moves downward , , Keep tires free of gasoline , oil , or insect control chemi - sharpen the heavy end until the blade is balanced . cals which can harm rubber . NOTE : Do not use a nai ! for balancing blade . The lobes of * Avoid stumps stones , deep ruts , sharp objects and the center hole may appear to be centered , but are not . other hazards that may cause t re damage . CENTER HOLE 7 / BLADE CARE / / For best results mower blades must be kept sharp _ Re - place bent or damaged blade & BLADE BLADE REMOVAL ( See Fig . 13 ) 5t8 " BOLT , Raise mower to highest position to allow access to J bfades _ , Remove hex bolt , lock washer and flat washer securing blade . , Install new or resharpened blade with trailing edge up FIG , 14 towards deck as shown . , Reassemble hex bolt , lock washer and flat washer in BATTERY exact order as shown . Your tractor has a battery charging system which is suffi - , Tighten bolt securely ( 30 - 35 Ft . Lbs . torque ) . cient for normal use . However , periodic charging of the IMPORTANT : BLADE BOLT IS GRADE 8 HEATTREATED . battery with an automotive charger will extend its life . NOTE : We do not recommend sharpening blade - but if you . Keep battery and terminals clean do , be sure the blade is balanced . • Keep battery bolts tight . MANDREL BLADE _ L _ , _ _ ASSEMBLY . Keep small vent holes open ° • Recharge at 6 - 10 amperes for 1 hour _ TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to " leak " power . FLAT WASHER _ . _ , _ % _ I / • Remove terminal guard , , LOCK WASHER _ _ _ _ _ / • Disconnect BLACK battery cable first then RED bat - tery cable and remove battery from tractor ° . Rinse the battery with plain water ' and dry ° HEX BOLT ( GRADE 8 ) _ • Clean terminals and battery cable ends with wire brush • AGRAD8EHEATTREATEBDOLCTANBE IDENTIFIED BY SiX LINES ON THE BOLT HEAD , until bright . • Coat terminals with grease or petroleum jelly . FIG . 13 o Reinstall battery ( See " CONNECT BATTERY " in the Assembly section of this manual ) . 18
Page: 19

, , Ulll n lU U , l , , , nuli ii , CUSTOMER RESPONS BUL ES . . . . . . . . . . . . . ulll , . . . . . . . . . . . . . . . . . TO CHANGE ENGINE OIL ( See Figs , 15 and 16 ) TRANSAXLE COOLING Determine temperature range expected before oil change The fan and cooting fins of transmission should be kept All oil must meet APf service classification SF or SG , c { ean to assure proper cooling . . Be sure tractor is on level surface , Do not attempt to clean fan or transmission while engine is . Oil will drain more freely when warm _ running or while the transmission is hot ° To prevent possible damage to seals , no not use high pressure water - Catch oil in a suitable container , or steam to clean transaxle o Remove oil fill cap / dipstick , Be careful not to allow dirt o Inspect cooling fan to be sure fan blades are intact and to enter the engine when changing oi ! , clean . • Remove drain plug , = Inspect cooling fins for dirt , grass clippings and other o After oil has drained completely , replace oil drain plug materials ° To prevent damage to seals , do not use and tighten securely , compressed air or high pressure sprayer . ° Refill engine with oil through oil fill dipstick tube . Pour TRANSAXLE PUMP FLUID slowly . Do not overfill , For approximate capacity seeis " PRODUCT SPECIFICATIONS " on page 3 of th The transaxle was sealed at the factory and fluid mainte - manual nance is not required for the life of the transaxle . Should o Use gauge on oil fill cap / dipstick for checking level . Be the transaxle ever leak or require servicing , contact your sure dipstick is in all the way for accurate reading ° nearest authorized service center / department . Keep oil at " FULL " line on dipstick , V - BELTS OIL DRAIN PLUG Check V - belts for deterioration and wear after 100 hours of operation and replace if necessary . The be _ ts are not AIR SCREEN adjustable . Replace belts if they begin to slip from wear . ENGINE LUBRICATION Only use high quality detergent oit rated with API service classification SF or SG . Select the oil's SAE viscosity grade according to your expected operating temperature . . . . . . . . SAE VISCOSITY GRADES ENGINE OIL FILL CAP1DIPSTICK aF " 20 _ 0 " 30 ° 32 ° 40 _ 60 " B0 _ 100 ° FIG . 16 ° c . _ o " . _ oo . _ o _ 0o ; o ' 20 , _ 0o 4o _ TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE FIG . 15 CLEAN AIR SCREEN ( See Fig . 16 ) Air screen must be kept free of dirt and chaff to prevent NOTE : AIthough muttFviscosity oifs ( 5W30 , 10W30 , etc . . ) engine damage from overheating , Clean with a wire brush improves starting in cold weather , these multi - viscosity oils or compressed air to remove dirt and stubborn dried gum will result in increased oil consumption when used above fibers . 32 ° C . Check your engine oil level more frequently to avoid possible engine damage from running low on oil . Change the oil after the first two hours of operation and every 50 hours thereafter or at beast once a year if the tractor is not used for 50 hours in one year Check the crankcase oil level before starting the engine and after each eight ( 8 ) hours of continuous use . 19
Page: 20

CLEAN AIR INTAKE / COOLING AREAS ENGINE OIL FILTER To insure proper cooling , make sure the grass screen , Replace the engine oil filter every season or every other oil cooling fins , and other external surfaces of the engine are change if the tractor is used more than 100 hours in one kept clean at all times . year . MUFFLER Every 100 hours of operation ( more often under extremely dusty , dirty conditions ) , remove the blower housing and inspect and replace corroded muffler and spark attester ( if other cooling shrouds . . Clean the cooling fins and external equipped ) as it could create a fire hazard and / or damage . surfaces as necessary . Make sure the cooling shrouds are reinstalled ° SPARK PLUGS NOTE : Operating the engine with a blocked grass screen , Replace spark plugs at the beginning of each mowing dirty or plugged cooling fins , and / or cooling shrouds re - season or after every 100 hours of operation , whichever moved will cause engine damage due to overheating . occurs first . Spark plug type and gap setting are shown in AIR FILTER ( See Fig . 17 ) " PRODUCT SPECIFICATIONS " on page 3 of this manual . Your engine will not run properly using a dirty air filter . IN - UNE FUEL FILTER ( See Fig , 18 ) Clean the foam pre - cleaner after every 25 hours of opera - tion or every season . Service paper cartridge every 100 The fuel filter shoutd be replaced once each season _ If fuel hours of operation or every season , whichever occurs first . filter becomes clogged , obstructing fuel flow to carburetor , replacement is require & Service air ' cleaner more often under dusty conditions . o Loosen knob and remove cover . " With engine cool , remove filter and plug fuel line sections . TO SERVICE PRE - CLEANER o Slide foam pre - cleaner off cartridge . o PLace new fuel filter in position in fuel line with arrow pointing towards carburetor _ = Wash it in liquid detergent and water _ o Squeeze it dry in a clean cloth . = Be sure there are no fuel line teaks and clamps are properly positioned . o Saturate it in engine oil Wrap it in clean , absorbent cloth and squeeze to remove excess oil . Immediately wipe up any spilled gasoline . TO SERVICE CARTRIDGE o Remove nut and cartridge plate _ o Gently tap the flat side of the paper cartridge to dis - lodge dfrL Do not wash the paper cartridge or use pressurized air , as this will damage the cartridge ° Replace a dirty , bent , or damaged cartridge . • Reinstall the pie * cleaner ( cleaned and oiled ) over the paper cartridge . . Check rubber seal for damage and proper position around stud , Replace if necessary . FIG . 18 o Reassemble air cleaner , cartridge plate , and nut . o Reinstafl air cleaner cover and secure by tightening knob . CLEANING o Clean engine , battery , seat , finish , etc . of all foreign matter _ CARTRIDGE o Keep finished surfaces and wheels free of all gasoline , oil , etc . FOAM PRE - CLEANER • Protect painted surfaces with automotive type wax . We do not recommend using a garden hose to clean your CARTRIDGE tractor unless the electrical system , muffler , air filter and PLATE \ \ RUBBER carburetor'are covered to keep water ouL Water in engine SEAL can result in a shortened engine Iife . FIG . 17 20
Page: 21

SERVICE AND ADJUSTMENTS i CAUTION : BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS : o Depress clutch / brake pedal fully and set parking brake , • Place motion control lever in neutral ( N ) position , o Place attachment clutch in " DISENGAGED " position . o Turn ignition key " OFF " and remove key ° o Make sure the blades and all moving parts have completely stopped . o Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug . TO LEVEL MOWER HOUSING TRACTOR Adjust the mower while tractor is parked on level ground or TO REMOVE MOWER ( See Fig . 19 ) driveway Make sure tires are properly inflated ( See " PRODUCT SPECIFICATIONS " on page 3 of this manual ) . • PTaceattachment clutch in " DISENGAGED " position _ Iftires are over or underinfiated , you wilt not properly adjust ° Turn height adjustment knob to lowest setting . your mower . o Lower mower to its lowest position . SIDE - TO - SIDE ADJUSTMENT ( See Figs , 19 and 20 ) ° Remove retainer spring holding anti - swaybar to chas - o Raise mower to its highest position , sis bracket and disengage anti - swaybar from bracket . - Measure height from bottom of deck curl to ogroundth ° Remove retainer springs from suspension arms at level at front corners of mower _ Distance " A " on b deck and disengage arms from deck ° sides of mower should be the same o Raise attachment lift to its highest position , ° If adjustment is necessary , make adjustment on one o Remove two retainer springs from each front link and side of mower only remove links . ° To raise one side of mower , tighten lift link adjustment o Slide mower forward and remove belt from electric nut on that side , clutch pulley . , To lower one side of mower , loosen lift link adjustment nut on that side , - Slide mower out from under right side of tractor . IMPORTANT : IF AN ATTACHMENT OTHER THAN THER , NOTE : Each half turn of adjustment nut will change mower MOWER DECK 1STO BE MOUNTED ON THE TRACTO height about 3 / 16 " . REMOVE THE FRONT LINKS o Recheck measurements after adjusting TO INSTALL MOWER BOTTOM BOTTOM OF CURL OF CURL Follow procedure described in " INSTALL MOWER AND DRIVE BELT " in the Assembly section of this manual FRONT SUSPENSION LIFT BRACKET , LINKS SUSPENSION ARMS ADJUSTMENT NUTS CHASSIS ELECTRIC CLUTCH PULLEY FRONT SUSPENSION BRACKET RETAINER RETAINER SPRING FRONT MOWER BRACKET ANTI - SWAY RETAINER BAR SPRINGS FIG . 19 21
Page: 22

TO REPLACE MOWER DRIVE BELT FRONT - TO - BACK ADJUSTMENT ( See Figs . 21 and 22 ) - IMPORTANT : DECK MUST BE LEVEL SIDE - TO - SIDE . IFtSSE MOWER DRIVE BELT REMOVAL ( See Fig . 23 ) - THE FOLLOWING FRONT - TO - BACK ADJUSTMENTLINKD NECESSARY , BE SURE TO ADJUST BOTH FRONTO - • Park tractor ' on a level surface . Engage parking brake . EQUALLY SO MOWER WILL STAY LEVEL SIDE - T SI ' , o Remove four screws from Loll , mandrel cover ' and To obtain the best cutting results , the mower housing remove cover . should be adjusted so the front is approximately 1 / 8 " to 1 / 2 " ° Roll belt over the top of L H , , mandrel pulley , , lower than the rear when the mower is in its highest position , o Remove belt from electric clutch pulley , = Remove belt from idler pulleyso Check adjustment on right side of tractor . Measure dis - tance " F " directly in front of and behind the mandrel at o Remove any dirt or grass clippings which may have bottom edge of mower housing as shown . accumulated around mandrels and entire upper deck sudace . • Before making any necessary adjustments , check that both front links are equal in length . , Check primary idler arm and two idlers to see that they o If links are not equal in length , adjust one link to same rotate freely . length as other link _ • Be sure spring is securely hooked to primary idler ' arm • Tolowerfront of mower housing , loosen nut " G " on both and bolt in mower housing , , front links an equal number of turns . - When distance " F " is 1 / 8 " to 1 / 2 " lower at front than MOWER DRIVE BELT INSTALLATION ( See Fig . 23 ) - e rear , tighten nut " H " against trunnion on both front links ° Install belt in both idlers . Make sure belt is in both belt • To raise front of mower housing , loosen nut " H " from keepers at the idlers as shown trunnion on both front tinks _ Tighten nut " G " on both * Install new belt onto electric clutch pulley . front links an equal number of turns . . Roll belt into upper groove of L . Ho mandrel pulley , - When distance " F " is t / 8 " to 1 / 2 " lower at front than rear , tighten nut " H " against trunnion on both front - Carefully check belt routing making sure belt is in the links . grooves correctly and inside belt keepers . NOTE : Each full turn of nut " G " will change dim . " F " by o Reassemble L . H . mandrelcover , approximately 3 / 8 " . o Recheck side - to - side adjustrnent . SCREWS L . H . ELECTRIC SPRING MANDREL ECLUTCHY MANDREL COVER PULL IDLER PULLEYS \ PRIMARY IDLER ARM FIG . 21 BOLT IN BOTH FRONT LINKS SHOULD BE EQUAL IN LENGTH HOUSING MANDREL \ \ MOWER \ \ DRIVE BELT BELT KEEPER FIG . 23 NUT " H " _ FRONT LINKS FIG . 22 22
Page: 23

SERVnCE AN ADJUSTMENTS i , i , , , i ii , , i ii1 , , i i iiipi , i1 _ 1111illllll i . . . . . . . . . . . . . . . . . . NOTE : After instalting a new electric clutch , run tractor at TO REPLACE MOWER BLADE DRIVE BELT full throttle and engage and disengage electric clutch 10 ( See Fig . 24 ) cycles to wear in clutch p _ ate _ Park the tractor on level surface _ Engage parking brake . , . Remove mower drive belt ( See " TO REPLACE MOWER DRIVE BELT " in this section of this manual ) ° RO _ CLUTCH PLATE o Remove mower ( See " TO REMOVE MOWER " in this o012 " section of this manual ) , SLOT { 3 . Remove four screws from R . H mandrel cover and remove cover ° Unhook spring from bolt on mower housing . • Carefully rol ! belt off RH _ mandrel pulley / - Remove belt from center mandrel pulley , idler pulley , NYLON LOCKNUT ( 3 ) BRAKE PLATE and L , , H . mandrel pulley . o Remove any dirt or grass which may have accumu - FIG . 25 lated around mandrels and entire upper deck surface , , . Check secondary idler arm and idfer to see that they rotate freely TO ADJUST BRAKE ( See Fig . 26 ) o Be sure spring is hooked in secondary idler arm and Your tractor is equipped with an adjustable brake system sway - bar bracket . which is mounted on the side of the transaxle • Install new belt in lower groove of L , , H . mandrel puUey , If tractor requires more than six ( 6 ) feet stopping distance idler pulley , and center mandrel pulley as shown . at high speed in highest gear , then brake must be adjusted . • Roll belt over R . H . mandrel puliey - Make sure belt is in ° Depress clutch / brake pedal and engage parking brake . all grooves properly , . Reconnect spring to bolt in mower housing and rein - • Measure distance between brake operating arm and stall RH mand [ el cover . nut " A " on brake rod , - Reinstall mower to tractor ( See " INSTALL MOWER , , tfdistance is other than 1 - 1 / 2 " , loosen jam nut and turn AND DRIVE BELT " in the Assembly section of this nut " A " until distance becomes t - 1 / 2L Retighten jam manual ) ° nut against nut " A " . • Reassemble mower drive belt ( See " TO REPLACE - Road test tractor for proper stopping distance as stated MOWER DRIVE BELT " in this section of this manual ) , above Readjust if necessary , if stopping distance is LH , MOWER BLADE still greater than six ( 6 ) feet in highest gear , further DRIVE BELT CENTER maintenance is necessary . Contact your nearest au - MANDREL thorized service centeddepartment . . MANDREL WITH PARKING BRAKE " ENGAGED " COVER NUT " A " / SCREW JAM NUT SECONDARY " / " ' " i I IDLER ARM _ , OPERATING , J L . , TO ADJUST ATTACHMENT CLUTCH ( See Fig . 25 ) The electric clutch should provide years of service , The FIG . 26 clutch has a built - in brake that stops the pulley within 5 seconds . Eventually , the internal brake will wear which may cause the mower blades to not engage , or , to not stop as required , Adjustments should be made by your nearest authorized service center / department , o Make sure attachment clutch and ignition switches are in " OFF " position , , . Adjust the three nylon tocknuts until space between clutch plate and rotor measures . , 012 " at all three slot locations cut in side of brake plate . 23
Page: 24

= , , , Hf SERVICE AN ADJU ENT $ TO REPLACE MOTION DRIVE BELT TO ADJUST , MOTION CONTROL LEVER ( See Fig . 28 ) ( See Fig . 27 ) Park the tractor on fevet surface ° Engage parking brake . The motion control lever has been preset at the factory and For ease of service there is a belt installationguide decal on adjustment should not be necessary . . bottom of left footrest , If for any reason the motion control lever wilt not hold its o Remove mower ( See " TO REMOVE MOWER " in this position while at a selected speed , it may be adjusted at the section of this manual . ) friction pack located on the right side of chassis . BELT REMOVAL = Park tractor on level surface ° Stop tractor by turning ignition key to " OFF " position and engage parking • Engage parking brake ( creates slack in belt ) o brake . ° Remove belt from clutching and fan idler pulleys . = Place motion control lever in neutral ( N ) position . o Remove belt from transaxle pulley . = While holding Iocknut , loosen jam nut • Remove belt from engine pulley and front V - idler • Tighten locknut 1 / 4turn . pulley . , While holding Iocknut , tighten jam nut securely . o Pull belt out of all belt keepers and remove from tractor _ NOTE : If for ' any reason the effort to move the motion BELT INSTALLATION - control lever becomes too excessive , reverse the above ° Place V part of belt into grooves on engine pulley and adjustment procedure by loosening tocknut 1 / 4 turn . front V - idler , making sure to route belt inside of all belt Road test tractor after adjustment and repeat procedure if keepers . necessary . , Route belt on right side , coming from V - idler , towards back of tractor , above midspan belt keeper and to top of transaxle pulley . LOCKNUT • Route belt on left side , coming from engine pulley , towards back of tractor and through loop in midspan JAM NUT belt keeper ' . , Place V part of belt into grooves on transaxle and fan idler pulleys , making sure to route belt inside of all belt keepers ° o Place belt around clutching idlers as shown , making sure to rou _ e belt inside of all belt keepers , o Check to be sure belt is positioned correctly and is on proper side of all belt keepers ° ° Reinstall mower . IMPORTANT : CHECK BRAKE ADJUSTMENT , TRACTOR V - BELT DRIVE SCHEMATIC VIEWED FROM L , H , SIDE OF TRACTOR CLUTCHING TRANSAXLE FIG . 28 CLUTCHING | DLER _ BELT ENGINE ABOVE TRANSMISSION REMOVAL / REPLACEMENT PULLEY VJDLER KEEPER Should your transmission require removal for service or replacement , it should be purged after reinstallation before operating the tractor ° See " PURGE TRANSMISSION " in Operation section of this manual BELT TWISTS BELT KEEPER TO ADJUST STEERING WHEEL ALIGNMENT FAN IDLER tf steering wheel crossbars are not horizontal ( left to right ) when wheels are positioned straight forward , rernove steer - ing wheel and reassemble per instructions inthe Assembty section of this manual AS VIEWED FROM BOTTOM FIG . 27 24
Page: 25

FRONT WHEEL TOE - IN ADJUSTMENT Front wheei toe - in is required for proper stee ring operation _ RETAINING Toe - in was set at the factory and adjustment should not be RING necessary . , If parts in the front axle or steering mechanism have been replaced or damaged , check toe - in and adjust AXLE ( ; OVER if necessary . " - , . . , . TO CHECK TOE - IN ( See Fig . 29 ) - o Position front wheels straight ahead , FIG , 31 . Measure distance between wheels at front and rear of tires ( dimensions " A " and " B " ) ° REAR WHEEL - , Front dimension " A " should be 1 / 8 " to 1 / 4 " less than - Block rear axle securely rear dimension " B " , . Remove five ( 5 ) hub bolts to allow wheel removal TO ADJUST TOEqN ( See Figs . 29 and 30 ) - o Repair tire and reassemble . Replace and tighten hub belts securely , - Loosen jam nuts at adjustment sleeves on tie rod . . Adjusttieroduntildimension " A " ist ! 8 " tol / 4 " Iessthan TOSTART ENGINE WITH A WEAK BATTERY dimension " B'L See Fig . 32 ) • Tighten jam nuts securely . _ d batteries gener * " _ _ - . Keep sparks , flame I _ _ ls away from bat * I protectionI " " , _ , wwhheenn aarroouunndd bbaatttteerriieessl , . . . . I If your battery is too weak to start the engine , it should be recharged , If " jumper cables " are used for emergency starting , follow this procedure : FIG . 29 IMPORTANT : YOUR TRACTOR iS EQUIPPED WITH A t 2REOR VOLT NEGATIVE GROUNDED SYSTEM THE OTHEVT VEHICLE MUST ALSO BE A 12 VOLT NEGATI GROUNDED SYSTEM . DO NOT USE YOUR TRAC BATTERY TO START OTHER VEHICLES TO ATTACH JUMPER CABLES ° Connect each end of the RED cable to the POSITIVE ( ¥ ) terminal of each battery , taking care not to short against chassis - Connect one end of the BLACK cable to the NEGA - TIVE ( - ) terminal of fully charged battery - Connect the other end of the BLACK cable to good FIG . 30 CHASSIS GROUND , away from fuef tank and battery . , TO REMOVE CABLES , REVERSE ORDER - • BLACK cable first from chassis and then from the fully FRONT WHEEL CAMBER charged battery . The front wheel camber is not adjustable on your tractor ° If RED cable Iast from both batteries , . damage has occurred to affect the front wheel camber , contact your nearest authorized service center / depart - ment . TO REMOVE WHEEL FOR REPAIRS " POSITIVE " ( + ) " NEGATIVE " ( - ) FRONT WHEEL ( See Fig 3I ) - o Block up axle securely . . o Remove axte cover , retaining ring and washers to allow wheel removal ° . Repair tire and reassembfe . • Replace washers and snap retaining ring securely in axle groove • Replace axle cover . . 25 Pit = . 32
Page: 26

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i , , , u . . . . . ADJUSTMENTS , i n , , lu , , , nnni TO REMOVE HOOD AND GRILL ASSEMBLY ( See Fig . 34 ) • Raise hood . Pull bulb holder out of the hole in the backside of the grill ° Unsnap headlight wire connector . Replace bulb in holder and push bulb holder securely • Stand in front oftractor , Grasp hood at sides , tilt toward back into the hole in the backside of the grill . engine and lift off of tractor . Close hood . • To replace , reverse above procedures . INTERLOCKS AND RELAYS Loose or damaged wiring may cause your tractor to run poorly , stop running , or prevent it from starting ° HEADLIGHT WIRE o Check wiring . See electrical wiring diagram in the CONNECTOR Repair Parts section of this manual HOOD TO REPLACE FUSE \ Replace with 30 amp automotive - type p ! ug - in fuse _ The ) , , fuse holder is located behind the dash . • ( , TO ADJUST ATTACHMENT LIFT SPRING ( See Fig . 33 ) o White holding spring bushing with wrench , loosenjam nut . , Turn adjustment bolt clockwise to extend spring and reduce lift effort for heavier attachments . = Turn adjustment bolt counterclockwise for lighter at - tachments FIG . 34 , Retighten jam nut against spring bushing . IMPORTANT : DO NOT ADJUST FOR MAXIMUM SPRINGCHING , TENSION WHEN USING LIGHT ATTACHMENTS RSUIDIN AS A MOWER . ADJUST LIFT LEVER SPRING TO AP LIFTING ATTACHMENT . DO NOT OVERPOWER S WHEN REMOVING ATTACHMENT , ALWAYS ADJUST SPRING TENSION TO ITS LOWEST POSITION . ADJUSTMENT SPRING BUSHING e ATTACHMENT JAMNUT LIFTSPRING o o FIG . 33 26
Page: 27

SERVmCE AND ADJUSTMENTS . . . . . . . . . . . . . . . . . . . I , NII , m i1 , , i , ii , i . . . . . . . . . . . . . . . . . ENGINE CLOSEFDOR TO ADJUST THROTTLE CONTROL CABLE ( See Fig . 35 ) The throttle control has been preset at the factory and adjustment should not be necessary . Check adjustment as described below before loosening cable . If adjustment is necessary , proceed as follows : • With engine not running , move throttle control lever to fast ( , _ ) position . • Check that speed control lever is against stop screw . If it is not , ! oosen casing clamp screw and pull throttlew cable until lever is against screw . . Tighten clamp scre securely . CLAMP SCREWS CHOKE CONTROL CABLEj FIG . 36 TO ADJUST CARBURETOR ( See Fig . 35 ) The carburetor has been present at the factory and adjust - ment should not be necessary . However , minor adjustment may be required to compensate for differences in fuel , THROTTLE temperature , altitude or load If the carburetor does need CONTROL adjustment , proceed as follows : CABLE • Be sure you have a clean air filter and the throttle control cabfe is adjusted property ( see above ) ° , Start engine and allow to warm for five minutes . Make finaf adjustments with engine running and shift / motion control lever in neutral ( tt ) position ° The high idle is set at the factory and cannot be adjusted . ° ld { e speed settinq - With throttle control tever in slow IDLE SPEED ( , _ ) position , _ ngine should idle at 1200 RPM If ADJUSTMENT engine idles too slow or fast , turn idle speed adjusting SCREW screw in or out until correct idle is attained FIG . 35 NOTE : The carburetor on this engine is Iow emission it is equipped with an idle fuel needle with a limiter cap and is not adjustable . Do not attempt to remove the fimiter cap . TO ADJUST CHOKE CONTROL The iimiter cap cannot be removed without breaking the ( See Figs . 35 and 36 ) adjusting needle . The choke control has been preset at the factory and High speed stop is factory adjusted Do not adjust - damage adjustment should not be necessary , check adjustment as may result . described below before loosening cable _ tf adjustment is IMPORTANT : NEVER TAMPER WiTH THE ENGINE necessary , proceed as follows : GOVERNOR , WHICH IS FACTORY SET FOR PROPERVEBE * With engine not running , move choke control ( located ENGINE SPEED . . OVERSPEEDING THE ENGINE NABO THE FACTORY HiGH SPEED SETTING CA on dash panel ) to fu ! l choke ( N ) position . . DANGEROUS iF YOU THINK THE ENGINE - GOVERNED - Remove air cleaner cover , filter and cartridge plate to HIGH SPEED NEEDS ADJUSTING , CONTACT YOUR / expose carburetor choke ( See " AIR FILTER " in the NEAREST AUTHORIZED SERVICE CENTER Customer Responsibilities section of this manual ) . DEPARTMENT , WHICH HAS PROPER EQUIPMENT YAND ° Choke should be dosed , if it is not , loosen casing EXPERIENCE TO MAKE ANY NECESSAR clamp screw and move choke cable until choke is ADJUSTMENTS completely closed . Tighten casing clamp screw se - curely . . - Reassemble air cleaner , 27
Page: 28

, i , iii1 , 1,1111 . . . . i iii , i , , , i STORAGE Immediately prepare your tractor for storage at the end of ENGINE the season or ' if the tractor will not be used for 30 days or more ° FUEL SYSTEM i ii , , i i , ii iiii I I I IMPORTANT : IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUELR , gasoline in the tank inside a building SYSTEM PARTS SUCH AS CARBURETOR , FUEL FILTELSO , where fumes may reach an open flame FUEL HOSE , OR TANK DURING STORAGE . AENDED CAUTION : Never store the tractor with or spark , Allow the engine to cool EXPERIENCE INDICATES THAT ALCOHOL BL before storing in any enclosure . FUELS ( CALLED GASOHOL OR USING ETHANOL OR , i , ii i ii iii IH , , METHANOL ) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURINGEL STORAGE . ACIDIC GAS CAN DAMAGE THE FU TRACTOR SYSTEM OF AN ENGINE WHILE IN STORAGE . , , Drain the fuet tank . Remove mower from tractor for winter storage ° When mower ' is to be stored for a period of time , clean it thor - . Start the engine and let it run until the fuel lines and oughly , remove all dirt , grease , leaves , etc . Store in a carburetor are empty . clean , dry area . • Never use engine or carburetor cleaner products inthe o Clean entire tractor ( See " CLEANING " inthe Customer fuel tank or permanent damage may occur . Responsibilities section of this manual ) . ° Use fresh fuel next season . • Inspect and replace belts , if necessary ( See belt re - NOTE : Fuel stabilizer is an acceptable alternative in placement instructions in the Service and Adjustments minimizing the formation of fuel gum deposits during stor - section of this manual ) _ age . Add stabilizer to gasoline in fuel tank or storage • Lubricate as shown in the Customer Responsibilities container _ Always follow the mix ratio found on stabilizer section of this manual . container . Run engine at least 10 minutes after adding • Be sure that all nuts , bolts and screws are securely stabilizer to allow the stabilizer to reach the carburetor . Do fastened . Inspect moving parts for damage , breakage not drain the gas tank and carburetor if using fuel stabilizer , and wear _ Replace if necessary . ENGINE OIL o Touch up all rusted or chipped paint surfaces ; sand lightly before painting . Drain oil ( with engine warm ) and replace with clean engine oil . ( See " ENGINE " in the Customer ' Responsibilities BATTERY section of this manual ) . • Fully charge the battery for storage _ CYLINDERS = After a period of time in storage , battery may require ° Remove spark plug ( s ) . recharging . ° To help prevent corrosion and power leakage durng , Pour one ounce of oil through spark plug hole ( s ) into long periods of storage , battery cables should be cylinder ( s ) o disconnected and battery cleaned thoroughly ( see " TO Turn ignition key to " START " position for a few seconds CLEAN BATTERY AND TERMINALS in the Cus - to distribute oil . tomer Responsibilities section of this manual ) . • Replace with new spark plug ( s ) . o After cleaning , leave cables disconnected and place cables where they cannot come in contact with battery OTHER terminals . = Be sure battery drain tube is securely attached , • Do not store gasoline from one season to another _ . If battery is removed from tractor for storage , do not • Replace your gasoline can if your can starts to rust . store battery directly on concrete or damp surfaces . Rust and / or dirt in your gasoline will cause problems . • If possible , store your tractor indoors and cover ' it to give protection frorn dust and dirt ° • Cover your tractorwith a suitable protective cover thatcid does not retain moisture . Do not use plastic . rPlasti cannot breathe which allows condensation to form a will cause your tractor to rusL IMPORTANT : NEVER COVER TRACTOR WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM . . 28
Page: 29

TROU LESHOO'F NG POINTS PROBLEM CAUSE CORRECTION Will not start ! Out of fuel 1 Fill fuel tank 2 Engine not " CHOKED " properly 2 See ' q'o START ENGINE " in Operation section 3 Engine flooded 3 Wait several minutes before attempting to start 4 Bad spark ptug 4 , Replace spark plug 5 Dirty air filter 5 Clean / replace air filter 6 Didy fuelfilter , 6 Replace fuel filter 7 Water in fuel 7 Drain fuel tank and carburetor , refill tank with fresh gasoline and replace fuel filter 8 , Loose or damaged wking 8 Check allwiring 9 Carburetor out of adjustment 9 , Contact an authorized service center ! department ! 0 Engine valves out of adjustment 10 Contact an authorized service center / department i , , , , U , lU , l , , n , u i Hard to start 1 Dirty air filter , 1 Clean / replace air filter 2 , Bad spark plug 2 Replace spark ptug 3 Weak or dead battery 3 Recharge or replace baflery 4 , Dirty fuel filter 4 Replace fuel filter 5 Stale ordirty fuel 5 Drain fuel tank and refill with fresh gasoline 6 , Loose or damaged wiring 6 Check al _ wiring 7 , Carburetor out of adjustment 7 Contact an authorized service center / department 8 Engine valves out of adjustment 8 Contact an authorized service center / department , , , , llU , , nl , , Engine will not turn over 1 Clutch / brake pedal not depressed 1 Depress clutch / brake pedal 2 Attachment clutch is engaged 2 Disengage attachment clutch 3 Weak ordead battery 3 Recharge or replace battery 4 Blown fuse 4 Replace fuse 5 Corroded batten / terminals 5 Clean battery terminals 6 Loose or damaged wiring 6 Check all wiring 7 Faulty ignition switch 7 ChecWreplace ignition switch 8 Faulty solenoid or starter 8 Checidreplace solenoid or starter g Faulty operator presence switch ( es ) 9 Contact an authorized service center / department Engine clicks but will not 1 Weak or dead battery I Recharge or replace battery start 2 Corroded battery terminals 2 Clean battery terminals 3 . Loose or damaged wiring 3 Check all wiring 4 Faulty solenoid or starter 4 , Check ! replace solenoid or starter 1 Loss of power Cutting too much grass / too fast t Set in " Higher Cut " position / reduce speed 2 Throttle in " CHOKE " position 2 Adiust throttle control 3 Build - up of grass , leaves and trash under mower , 3 Clean underside of mower housing 4 Dirty air filter 4 Clean ! replace air filter 5 Low oil level / dirty oil 5 Check oil level / change oil 6 Faulty spark plug 6 Clean and regap or change spark plug 7 Dirty fuel filter . 7 Replace fuel filter 8 Stale or dirty fuel 8 Drain fuel tank and refil ! with fresh gasoline g Water in fuel 9 Drain fuel tank and carburetor , refill tank with fresh gasoline and replace fuel filter 10 Spark plug wire loose 10 Connect and tighten spark plug wire 11 Dirty engine air screen / fins 11 Clean engine air screen / lids 12 Didyiciogged muffler t2 Clean ! replace muffler 13 Looseor damaged wiring ! 3 CheckaIt wiring 14 Carburetor oat of adjustment I4 Contact an authorized service center / department 15 Engine valves out of adjustment , 15 Contact an auIhorized service center / department i , , , , , llllll , nl , i Excessive vibration 1 Worn , bent or loose blade 1 Replace blade Tighten blade boll 2 , Bent blade mandrel 2 Replace blade mandrel 3 Loose ! damaged pad ( s ) 3 Tighten loose pad ( s ) Replace damaged parts 29
Page: 30

= = PROBLEM CAUSE CORRECTION H , H = = H ' 1 . . . . ' HLI , ' , , H N , = H ' Engine continues to run 1 , Faulty operator - safety presence control system , 1 Check wiring , switches and connections If not when operator leaves seat corrected , contact an authorized service canted with attachment clutch department engaged Poor cut - uneven 1 Worn , bent or loose blade 1 Replace blade Tighten blade bolt 2 . Mower deck not level , . 2 , Level mower deck . 3 Buildup of grass , leaves , and trash under mower 3 , Clean underside of mower housing 4 Bent blademandrei 4 Replace blade mandrel , 5 Clogged mower deck vent holes from buildup of 5 CJean around mandrels to open vent holes grass , leaves , and trash around mandrels , = , = 1,11,1 , , , Mower blades will not ! Obstruction in clutch mechanism 1 Remove obstruction rotate 2 Worn / damaged mower drive belt 2 Replace mower drive belt 3 . Frozen idler puitey , 3 . Replace idler pulley . 4 , Frozen blade mandrel 4 . Replace blade mandrel H = H , , ' 1 Poor ' grass discharge 1 Engine speed too slow 1 , Place throttie control in " FAST " position 2 , Travel speed too fast 2 , Shift to slower speed . 3 Wet grass 3 . Allow grass to dry before mowing , 4 Mower deck not level . 4 Level mower deck 5 Lowfuneven tire a _ rpressure . 5 Checktires for proper air pressure , 6 Worn , bent or loose blade 6 Replacetsharpen blade Tighten blade boil , 7 , Buildup of grass , leaves and trash under mower , 7 Clean underside of mower housing 8 Mower drive belt worn . 8 Reptace mower drive belt 9 . Blades impropedy installed , 9 Reinstall blades sharp edge down 10 improper blades used 10 Replace with blades listed in this manual 11 Clogged mower deck vent holes from buildup of 11 , Clean around mandrels to open vent holes grass , leaves , and trash around mandrels i = = l Headlight ( s ) not working 1 Switch is " OFF " . ! , Turn switch " ON " ( if so equipped ) 2 , Bulb ( s ) burned out . 2 Replace bulb ( s ) , 3 , Faulty light switch 3 Check / replace light switch . 4 Loose or damaged wiring 4 Check wiring and connections 5 . Blown fuse . 5 . Replace fuse Battery will not charge 1 . Bad battery cell ( s ) , 1 Replace battery 2 . Poor cable connections 2 . Check / clean aH connections 3 . Faulty regulator ( if so equipped ) . 3 Replace regulator 4 Faulty alternator , 4 Replace afternator = = = = = = = = = = = = = = = = = 1 HHHH = I = Loss of drive 1 . Freewheel control tn " disengaged " position . 1 Place freewheel contreJ in " engaged " position 2 Motion drive beE ! worn , damaged or broken , 2 , Replace motion drive belt . 3 Air trapped in transmission during shpmant 3 Purge transmission or servicing = = = = = = = = = = = = = = = = = = = = = HHH = = Eng | ne " backfires " Engine throttle control not set at " SLOW ' Move throtUe control to " SLOW " position and allow when turning engine position for 30 seconds before stopping engine . to idle for 30 seconds before stopping engine " OFF " H , rH , , = 1 = = = = = = = 1 = 1 I ' 1 " 3O
Search in Tractors-Riding-Lawnmowers on ebay
"
* Clicking the part number will send you to Sears Parts Direct.
1142874 Assembly, housing, lh
103142916 Washer
104142917 Vent cap
106142918 Fitting
108142919 Control arm
109142920 Set screw
110142921 Head filter
111150820 Hose 1/2"
112150823 Fitting
113150821 Fitting
117150822 Fitting
123150824 O-ring
124150825 Pinch clamp
129153771 Spring
16142876 Brake shaft
2142875 Housing
20142877 Axle
21142878 Washer 1.0 x 1.63 x .08
22142879 Washer 1.0 x 2.06 x .09
33142929 Brake
35142880 Brake
36142882 Puck
37142883 Brake
38142884 Washer
39142885 Nut, castle 5/16-24
40142886 Cotter pin
41142887 Brake
42142888 High pro key
43142889 Spacer
45142890 Brake
46142891 Bolt 1/4-20 x 1-1/2
47142892 Bolt
49153766 Differential assembly
63142894 Dowel pin
64150818 Reduction gear, 14 teeth to 38 teeth
65142897 Pinion
67142898 Jackshaft
68142899 O-ring
69142900 Washer
7153765 Oil seal
70142901 Washer
71142902 Bolt
72153767 Locknut, hex 5/16-18
73142904 Bolt, hex 5/16-18 x 1-1/2
74142905 Hex cap screw 5/16-18 x 1
76142907 Bolt
77142908 Actuating arm freewheel
78142909 Oil seal
79153768 Grease (10 oz. tube)
81142910 Bolt
82142911 Bolt
89142912 Filter, spin on
91153769 Pump assembly, complete
95142914 Plug
96153770 60 degree 7/18 sae x 5/16 fitting
1144569 Shaft pump
12122717X Seal, lip
13122748X Arm, trunnion
14122749X Guide, slot
15144571 Housing kit, transmission
17122770X Bearing, thrust, ball
19153801 Center section kit
2122716X Ring, retaining
21122722X Seal, lip (included in 59)
22144573 Shaft motor
23142978 Washer
25127148X Swashplate, variable
3122745X Bearing, ball
32142938 Block assembly
37122786X Pin, stainless, headless
38122718X Gasket
4122715X Spacer
42144578 Kit valve
43144578 Kit valve
44144579 Charge kit
47122752X Screw, socket head, cap
5122700X Seal, lip
53127153X Kit valve
6122699X Ring, retaining
60142977 Spring
62144581 Ring
63144582 Charge pump kit
64144583 Gerotor assembly
67144584 Screw, socket head, cap
8122767X Bearing, cradle
99153769 Pump assembly, complete
0144334 Sealant, tire (10 oz. tube)
08022J Plug
0154488 Manual, owner's (span)
0154487 Manual, owner's (eng)
0150073 Transaxle hydro
0145247 Fastener
0145245 Pad footrest
0143651 Mandrel
0141051 Mower service
033006 Tune-up kit (spark plug, oil, air filter, oil f...
1146142 Battery
10145211 Bolt wet btr 1/4-20 x 7.5 zinc
11145209 Hold down battery dash mount
12145769 Nut push nylon 1/4" wet battery
274760412 Bolt
21136850 Harness
224152J Bulb
26108824X Fuse
286508R Cable battery 4 gauge 12"
29121305X Seat switch
3STD551125 Washer, lock 1/4
30144921 Switch, ign
31140400 Nut, ignition switch
32141226 Cover key switch
33140403 Key ignition molded craftsman, delta
34110712X Switch
39109553X Interlock switch
4STD551025 Washer 9/32 x 5/8 x 16 ga
40150384 Harness ign.
45122822X Ammeter
46110940X Meter hour
4717011008 Screw
49153249 Pinned washer
50146283 Switch, pto
51140405 Retainer ring pto switch
5371031008 Screw hex washer hd no. 10-32 x 1
5473951000 Nut
6STD541025 Nut fin hex 1/4-20
77697J Tube plastic
87603J Tray
9109596X Hose clamp
0144334 Sealant, tire (10 oz. tube)
08022J Plug
0154488 Manual, owner's (span)
0154487 Manual, owner's (eng)
0150073 Transaxle hydro
0145247 Fastener
0145245 Pad footrest
0143651 Mandrel
0141051 Mower service
033006 Tune-up kit (spark plug, oil, air filter, oil f...
1150253 Rail, frame rh
1019092016 Washer
100124236X Cap by pass rod
10117490628 Screw
1024497H Retainer, spring
103142273 Lock, by pass
106138776 Bolt 5/16-18 type tt
11137270 Rivet, ratchet male
12137269 Washer
12019131616 Washer 13/32 x 1 x 16 ga.
13137271 Rivet
133150542 Skirt with insert fender vgt rh
134150543 Skirt with insert fender vgt lh
135152923 Screw hex head sems no. 10-24 x 3/4 gr. 2
14136673X558 Hood assembly, pnt
15136374 Lens, bar clear
16121794X Cover
1717490612 Screw, thdrol 3/8-16 x 3/4
18136373X428 Grille
1919131312 Washer
2140506 Drawbar, gt
20STD523710 Bolt, fin hex 3/8-16 x 1
21STD541437 Nut, crownlock 3/8-16 unc
22136670X558 Panel assembly, side rh
2317490616 Screw thdrol 3/8-16 x 1 ty-tt
24145243X558 Footrest, rh
28145244S558 Footrest, lh
29145349 Bracket, support dash
3136671X558 Panel assembly, side lh
30145052 Saddle
31145183 Brace, support steering
32141315 Bracket assembly, frame pivot, left hand
33141314 Bracket assembly, frame pivot, right hand
34142131 Bracket
3674780512 Bolt
37150672X558 Fender, pnt.
3819091216 Washer 9/32 x 3/4 x 16 ga.
39136961 Bracket, axle front
473800700 Nut
40142132 Bracket, support axle/engine
4117580408 Screw
4272140608 Bolt, carriage 3/8-16 x 1
43136939 Bracket
44136940 Bracket
45138460 Bracket assembly, susp chassis rh
4717490608 Screw
48142133 Bracket assembly, pivot hood lh
49142134 Bracket assembly, pivot hood rh
5145203 Dash, plastic black
50152728 Chassis bracket
52STD541431 Nut, crownlock 5/16-18
56138461 Bracket assembly, susp chassis lh
5773640400 Nut
58137113 Bracket
5974180412 Screw
6150273 Dash assembly, lower
6017490620 Screw thdrol 3/8-16 x 1-1/4
6319131614 Washer 13/32 x 1 x 14 ga.
64144283 Washer, serrated disc 13/32 x 1
6817490508 Screw
717720408 Screw
70137159 Guide, belt mid span
77137308 Shield, front
8145166 Support, battery
84142992 Stop
8674760716 Bolt, fin hex 7/16-14 unc x 1
9108067X Nut
9011050600 Washer, lock external tooth 3/8
91150851 Rail, frame lh
92146967X011 Plate, silkscreen dash
94100207K Clip
95105531X Nut
98140503 Bracket skid chassis
99140871 Rod
0144334 Sealant, tire (10 oz. tube)
08022J Plug
0154488 Manual, owner's (span)
0154487 Manual, owner's (eng)
0150073 Transaxle hydro
0145247 Fastener
0145245 Pad footrest
0143651 Mandrel
0141051 Mower service
033006 Tune-up kit (spark plug, oil, air filter, oil f...
100126881X Washer
10159285 Washer
10273560500 Nut hex nylok
10373350500 Nut, hex, jam 5/16 - 18 (standard hardware--pur...
104140480 Bracket
10517580408 Screw
106142576 Fitting vent hose
107142577 Vent hose
108142578 Cap vent hose
109140929 Spring return brake
11088652 Hinge screw
15STD551037 Washer 13/32 x 13/16 x 16 ga
17140921 Spring rod
27070E Key 1/4 x 2.5
2073940800 Nut
22140498 Shaft arm assembly
23130564 Knob pistol
28STD541237 Nut
29140494 Brake rod
37563R Washer
3019131616 Washer 13/32 x 1 x 16 ga.
3273220700 Nut
3312000053 Ring e #5133-100
34124236X Cap plunger
35137648 Park brake
36149412 Spring, drive, ground
37121749X Washer
38150035 Nyliner bushing
3974321016 Screw fin no. 10-24 x 1
405304J Actuator interlock switch
4173631000 Nut lock no. 10-24
428883R Pedal cover
4374760412 Bolt
44104601X Bracket interlock
4573800400 Lock nut
46145170 Retainer
47138228 Clutch rod
4872110614 Bolt carriage 3/8-16 x 1-3/4 gr 5
4919131413 Washer
5STD541437 Nut crownlock 3/8-16
50131494 Pulley idler flat
51STD541437 Nut crownlock 3/8-16 unc
52139123 Pulley
53207J Washer
54138390 Cluth arm assembly
55105706X Bearing
56140218 V-belt 84.5 x .490 vgth
5874760724 Bolt
6STD561210 Pin cotter 1/8 x 3/4
61140488 Pulley
64137649 Shaft assembly brake parking clutch
6567609 Bolt shoulder
66140296 Washer
6719131312 Washer
685142H Pin roll
69123800X Washer
7140507 Hub wheel
70151146 Console hydro fender
71151179 Plate console
72STD541431 Locknut hex with washer insert
7374780548 Bolt
74142432 Screw
7573800700 Nut
76140481 Bracket
7774760716 Bolt fin hex 7/16-14 x 1
7819111212 Washer
7972110505 Bolt carriage 5/16-18 x 5/8
80140484 Bracket
8117490612 Screw thdrol 3/8-16 x 3/4
82150586 Bracket mount torrque/fan
83140479 Strap
84140490 Spacer
8517541020 Screw
86140462 Fan
87140491 Adapter
88140492 Pulley idler
8973680700 Nut
9140080 Bolt
90140489 Keeper belt
9117490644 Screw hexwsh thdrol 3/8 - 16 x 2 - 3/4
9274760520 Bolt
93140502 Link
94133835 Fastener
9523200528 Screw
96141103 Washer
97126874X Bearing trust
98141004 Bracket
9917490624 Screw thdrol 3/8-16 x 1-1/2
0144334 Sealant, tire (10 oz. tube)
08022J Plug
0154488 Manual, owner's (span)
0154487 Manual, owner's (eng)
0150073 Transaxle hydro
0145247 Fastener
0145245 Pad footrest
0143651 Mandrel
0141051 Mower service
033006 Tune-up kit (spark plug, oil, air filter, oil f...
1121472X Wheel, steering
1074781044 Bolt
11136518 Spacer
1273901000 Nut
13121749X Washer
14STD551137 Washer, lcok hvy hlcl spr 3/8
1573610600 Nut, fin hex 3/8-24 unf
16145103 Shaft
17137347 Rod assembly, tie ball j abll vgt (inc. keyno. ...
18137155 Draglink, ball joint solid vgt
19146611 Support assembly, steering vgt
2137094 Axle assembly, front
20145182 Column, steering
21100711L Adapter, wheel steering
221554J Bushing, strg. blk
23152927 Screw, tt no. 10-32 x 5 x 3/8 flange
2419133808 Washer 13/32 x 2-3/8 x 8 ga.
25STD523710 Bolt, fin hex 3/8-16 x 1 gr. 5
26126805X Insert
273366R Bearing
2817490612 Screw, thrdrol 3/8-16 x 3/4
29104239X Bearings
36855M Zerk grease fitting
3012000034 Ring
31138136 Bushing
3219111610 Washer
33STD551131 Washer, lock hvy hlcl spr 5/16
34STD523107 Bolt, hex hd 5/16-18 x 3/4
35138059 Gear
36137156 Tie rod
3773360600 Nut
38109850X Joint assembly ball right hand thread
3973700600 Nut
4136960 Spindle assembly, lh
40109851X Joint assembly ball left hand thread
5136959 Spindle assembly, rh
66266H Thrust washer
7121748X Washer
812000029 Ring
9121232X Cap
0144334 Sealant, tire (10 oz. tube)
08022J Plug
0154488 Manual, owner's (span)
0154487 Manual, owner's (eng)
0150073 Transaxle hydro
0145247 Fastener
0145245 Pad footrest
0143651 Mandrel
0141051 Mower service
033006 Tune-up kit (spark plug, oil, air filter, oil f...
1N/P Engine, kohler, cv25s-69511 (div 71/501)
10105432X Bushing
11140923 Clutch electric
12143996 Pulley
15151346 Fuel tank
16109227X Pad idler
17106082X Pad
18151296 Cap assembly fuel with guage vented
1913290300 Cap
2150250 Pre muffler
20132756 Control throttle
2117720410 Screw hex thd cut 1/4-20 x 5/8
22132781 Choke control
2319132616 Washer
24STD551237 Lockwasher ext tooth 3/8
2573920600 Nut
263645J Bushing
27139277 Stem
287834R Fuel line
29132922 Arrestor
33STD541437 Nut lock hex with ins 3/8-16 unc
37123487X Clamp hose
3874780624 Hex bolt
3917490636 Screw
4017490664 Screw tt 3/8-16 x 2-1/4 unc
41126197X Washer
42STD551143 Washer lock 7/16
43150280 Bolt
45M73030800 Flange m nut
47142040 Spacer
4819132007 Washer
513200300 Elbow std 90 degree 3/8-18 npt
50143020 Duct air vgt sears kohler cv25
5217580408 Screw
53143528 Bracket
5419131414 Washer flat 13/32 x 7/8 x 14 ga.
5513090336 Nipple pipe 3/8 npt x 4-1/2
5613090308 Nipple
6417490612 Screw thdrol 3/8-16 x 3/4 ty-tt
6519131614 Washer 13/32 x 1 x 14 ga.
6717490512 Screw thdrol 5/16-18 x 3/4 tyt
7151396 Guard . muffler
72150249 Muffler vgt side mount 25hp
73153992 Shield heat
8121361X Pulley v-idler
9145109 Stop keeper assembly vgt
0144334 Sealant, tire (10 oz. tube)
08022J Plug
0154488 Manual, owner's (span)
0154487 Manual, owner's (eng)
0150073 Transaxle hydro
0145247 Fastener
0145245 Pad footrest
0143651 Mandrel
0141051 Mower service
033006 Tune-up kit (spark plug, oil, air filter, oil f...
1140124 Seat
10140552 Pan, seat
12121246X Bracket
13121248X Bushing
1472050411 Bolt, carriage 1/4-20 x 1-3/8
15121249X Split spacer
16123740X Compression spring
17123976X Nut, lock 1/4 lge flg gr. 5
1819171912 Washer
19120068X Knob, seat 1/2-13 unc
2140551 Bracket pivot
20124238X Spring cap
21153236 Bolt, shoulder 5/16-18 unc
22STD541431 Nut, crownlock 5/16-18 unc
3140675 Strap
4127018X Bolt
5145006 Clip push-in hinged (96012001102)
6STD541437 Nut, crownlock 3/8-16 unc
7124181X Spring
8150176 Bolt
0144334 Sealant, tire (10 oz. tube)
08022J Plug
0154488 Manual, owner's (span)
0154487 Manual, owner's (eng)
0150073 Transaxle hydro
0145247 Fastener
0145245 Pad footrest
0143651 Mandrel
0141051 Mower service
033006 Tune-up kit (spark plug, oil, air filter, oil f...
1121006X Lever rod
102876H Spring
11146704 Link lift
123146R Retainer, spring
13139868 Arm suspension
14140302 Bearing, pvt. lift spherical
15STD541437 Nut, crownlock 3/8-16 unc
16674A247 Spring - ass'y. - assist, lift
17STD541237 Nut, hex jam 3/8-16 unc
18143363 Bracket, spring asseist
19STD551037 Washer 13/32 x 13/16 x 16 ga.
2145542 Shaft assembly, lift vgt
205328J Bolt
21STD523710 Bolt, fin hex 3/8-16 x 1
22127218 Front Link
234939M Retainer, spring
2473350800 Nut, jam hex 1/2-13 unc
25130171 Trunnion
2673800800 Nut, lock with wsh 1/2-13 unc
29150233 Trunnion
3121002X Lever assembly, lift rh
30110807X Nut
3119131016 Washer
32137150 Spring
3376020308 Pin, cotter 3/32 x 1/2
34137167 Adjustable rod
35138057 Knob
3617490612 Screw, thdrol 3/8-16 x 3/4
37120529X Washer
38123933X505 Pointer
39123935X Hole plug
412000022 E - ring truarc #5133 - 87
4017490512 Screw thdrol 5/16-18 x 3/4
4173540600 Crownlock nut
4219112410 Washer
43123934X Scale, indicator, height
519292016 Washer
674780624 Hex bolt
7125631X Grip
70145212 Hex nut
8122365X Button, plunger
9122364X Plunger, lever lift
0144334 Sealant, tire (10 oz. tube)
08022J Plug
0154488 Manual, owner's (span)
0154487 Manual, owner's (eng)
0150073 Transaxle hydro
0145247 Fastener
0145245 Pad footrest
0143651 Mandrel
0141051 Mower service
033006 Tune-up kit (spark plug, oil, air filter, oil f...
1136457 Deck assembly, mower 50" vented
10140296 Washer
11137380 Blade
12129895 Bearing
13137553 Shaft
14137152 Housing
15110485X Bearing
16140329 Stripper, mower round
17106735X Rod
1819111016 Washer
19105304X Cap
2STD541431 Nut, crownlock 5/16-18
20123713X Spring
21137607 Deflector bracket
22110452X Push nut
23110509X Deflector
24136320 Runner - rh
2519111216 Washer
27STD551037 Washer 13/32 x 13/16 x 16 ga.
28132823 Spacer, spring stop idler
29STD541437 Nut, lock hex with wsh 3/8-16 unc
372110506 Bolt, carriage 5/16-18
30138776 Screw thdrol hex head
31137266 Nut, flg top lock cntr 9/16
32153532 Pulley, mandrel
33129963 Washer, spacer mower vented
3472140610 Bolt, carriage 3/8-16 x 1-1/4
3572110616 Bolt, carriage 3/8-16 x 2
3672110608 Bolt, carriage 3/8-16 x 1 gr. 5
37137166 Stiffener
38137554 Keeper, belt idler
39131494 Pulley, idler flat
47631J Runner, mower left hand
40136572 Pulley
42STD533107 Bolt, carriage 5/16-18 unc x 3/4
43136460 Arm
44122052X Spacer, retainer
45STD541437 Nut, crownlock 3/8-16 unc
4674760628 Bolt
47137200 Cover
48137729 Screw
49136574 Cover
5138457 Bracket
50137272 Arm
51137273 Spring
52139245 Pulley
53137789 Shield
54139573 Belt
55144959 Belt
56138687 Spring
57136577 Bar
58133957 Gauge wheel
59137644 Bolt, shoulder
64939M Retainer, spring
60139031 Clevis pin
61136573 Bracket
62133943 Washer hardened
6372110612 Bolt
6419121414 Washer 3/8 x 3/4 x 14 ga.
65151831 Pulley, flat, idler
66139622 Keeper, belt, idler
6773930600 Lock nut
7130832 Arm suspension, rear
8850857 Bolt blade
9STD551137 Washer, lock hvy 3/8 unplated
94STD523710 Bolt fin hex 3/8-16 unc x 1
95132274 Bracket assembly noseroller lh
96132273 Bracket assembly noseroller rh
9719171416 Washer
98132264 Roller/nose 38 and 42
9972110614 Bolt, carriage 3/8-16 x 1-3/4 gr. 5
0144334 Sealant, tire (10 oz. tube)
08022J Plug
0154488 Manual, owner's (span)
0154487 Manual, owner's (eng)
0150073 Transaxle hydro
0145247 Fastener
0145245 Pad footrest
0143651 Mandrel
0141051 Mower service
033006 Tune-up kit (spark plug, oil, air filter, oil f...
1138955 Decal, operating instruction
10137537 Decal, caution
114900J Decal, clutch/brake
12146790 Decal
13146711 Decal
14139346 Decal, v-belt schematic
15142241 Decal, panel side
16146709 Decal fender
17150333 Decal cap cnsmr help line srs
18146710 Decal, insert strg
19138047 Decal
20140837 Decal, brake parking slt saddle
21142336 Decal sdl cold start
22149516 Decal battery danger/poison english assembly
23106202X Reflector
24149918 Decal, fender auto trans srs, gld
26151448 Decal, grille garden tractor ipc
3146705 Decal, hood, craftsman, rh
4146706 Decal, hood, craftsman, rh
6133644 Decal
7138048 Decal, side panel
8146707 Decal, ins. hood
9142342 Decal
0144334 Sealant, tire (10 oz. tube)
08022J Plug
0154488 Manual, owner's (span)
0154487 Manual, owner's (eng)
0150073 Transaxle hydro
0145247 Fastener
0145245 Pad footrest
0143651 Mandrel
0141051 Mower service
033006 Tune-up kit (spark plug, oil, air filter, oil f...
159192 Valve cap
107154J Tube
11104757X Cap hub axle blk 1.50 x 1.00
265139 Valve stem
3148741 Tire, front
48134H Tube
5148736X427 Rim assembly, front
66856M Zerk grease fitting
79040H Flange bearing
8148738X427 Rim
9151607 Rear Tire
024-789-02-S Maintenance co kit
124-522-72 Cylinder block (use short block)
1024-012-05 Camshaft
1124-144-01 Shaft, governor cross
12X-25-63 Washer, plain 1/4
1312-032-01 Seal, governor cross
14X-25-102 Washer, plain 1/4
1512-380-04 Pin, hitch
16M-0545010 Screw, hex flange m5 x 0.8 x 10
1724-018-04 Retainer, reed
1824-402-05 Reed, breather
1924-032-01 Seal, oil, front
224-294-03 Fitting
2012-153-01 O-ring, lower oil fill tube
2112-123-04 Tube, oil fill
2224-126-19 Bracket, oil fill tube
23M-0545016 Screw, hex flange m5 x 0.8 x 16
2412-153-02 O-ring, upper oil fill tube
2524-038-04 Dipstick assembly (includes 26-27)
2625-755-13 Kit, oil fill cap (includes 27)
2712-153-03 O-ring, dipstick
324-067-05 Connecting rod (standard)
3A24-067-06 Connecting rod (.25)
412-380-03 Pin, dowel locating
553-139-09 Plug, cup
624-874-04 Piston with ring set (standard)
724-108-04 Ring set (standard)
824-018-01 Retainer, piston pin
912-422-10 Shim, camshaft, yellow
9A12-422-09 Shim, camshaft, red (as required)
9B12-422-13 Shim, camshaft, black (as required)
9C12-422-07 Shim, camshaft, white (as required)
9D12-422-08 Shim, camshaft, blue (as required)
9E12-422-11 Shim, camshaft, green (as required)
9F12-422-12 Shim, camshaft, grey (as required)
024-789-02-S Maintenance co kit
124-318-17 Head assembly, no. 1 cylinder
1024-326-14 Hose, breather
1112-755-03 Kit, retainer
1212-173-01 Cap, valve spring
1324-089-02 Spring, valve
14235011 Retainer, spring
1524-016-01 Valve, exhaust, standard size
15A24-016-02 Valve, exhaust, .25 oversize
1624-017-01 Valve, intake, standard size
16A24-017-02 Valve, intake, .25 oversize
1724-032-05 Seal, valve stem
1824-294-06 Fitting
1924-326-13 Hose, breather
224-755-76 Kit, valve cover, breather (includes key no. 3,...
2012-351-01 Lifter, valve
2124-411-05 Rod, push
2224-041-16 Gasket, cylinder head
2324-318-18 Head assembly, no. 2 cylinder
2424-755-66 Kit, valve train (includes key no. 21, 25-26)
2524-186-01 Arm, rocker
2624-599-01 Pivot, rocker arm
27M-0640034 Screw hex flange m6 x 1.0 x 34
2824-755-74 Kit, valve, cover, plain (includes key numbers ...
2924-153-12 O-ring
325-313-02 Grommet, rubber
3024-086-32 Screw, shoulder
3124-086-16 Screw hex flange m10 x 1.5 x 90
3224-445-01 Strap, lifting
3324-755-57 Kit, breather seprator (includes key numbers 34...
3424-112-12 Spacer
3524-126-44 Bracket, breather separator
3625-313-02 Grommet, rubber
3724-445-02 Strap, breather separator
38M-0545016 Screw hex flange m5 x 0.8 x 16
424-033-03 Kit, breather cover with gasket (includes key n...
524-041-23 Gasket, breather
624-096-15 Cover, breather
7M-0645020 Screw hex flange m6 x 1.0 x 20
8X-75-23 Plug, hex head, allen head 1/8 n. pipe
9X-426-9 Clamp, hose
024-789-02-S Maintenance co kit
124-162-17 Screen, grass
1025-403-03 Rectifier-regulator
1124-086-18 Screw, phillips head (2) 11-16 x 7/8
12236602 Connector, rectifier-regulator, 3 contact
1312-132-02 Spark plug
1448-154-02 Clip cable
1512-468-03 Washer, plain
1612-086-14 Screw, hex flange m10 x 1.5 x 46
1724-085-01 Stator, 15 amp
18M-0548025 Screw, hex cap m5 x 0.8 x 25
19X-25-63 Washer, plain 1/4
2M-0403025 Screw, hex cap m4 x 0.7 x 25
20X-25-92 Washer, plain 3/16
2147-154-01 Clip, cable
2224-584-03 Module, ignition, need (2) per engine
23M-0560025 Screw, hex socket head m5 x 0.8 x 25
24M-0448010 Screw, hex flange m4 x 0.7 x 10
2524-584-05 Module, speed advance
3X-25-92 Washer, plain 3/16
424-112-04 Spacer, fan
524-157-03 Fan
6M-0639016 Screw hex flange m6 x 1.0 x 16
712-112-01 Spacer, fan
824-025-08 Flywheel assembly
9X-42-15 Key
9924-176-27 Harness, wire
99A25-518-28 Lead, black (4", 18 gauge, insulated grip barre...
99B24-113-18 Decal, grass screen
99C24-468-12 Washer, graphite (4) 5 mm
99D24-063-27 Baffle, heat shield
024-789-02-S Maintenance co kit
124-755-91 Kit, knob with gasket (includes 2)
1024-041-13 Gasket, fuel spitback cup
1124-094-13 Base, air cleaner
1224-041-14 Gasket, air cleaner base
1324-164-06 Mainfold, intake
1424-041-01 Gasket, intake manifold
15M-0651055 Screw m6 x 1.0 x 18
225-341-02 Knob, cover
324-096-42 Cover, air cleaner
412-100-01 Wing nut
524-096-01 Cover, inner air cleaner
6230046 Seal
724-083-05 Element, pre-cleaner
824-083-03 Element, air cleaner
924-109-05 Cup, fuel spitback
9912-113-53 Decal, air cleaner
024-789-02-S Maintenance co kit
124-027-32 Housing, blower
10M-0545010 Screw hex flange m5 x 0.8 x 10
1124-063-14 Baffle, valley, no. 2 side
12M-0545016 Screw hex flange m5 x 0.8 x 16
1324-063-31 Baffle, cylinder barrel, no. 1 side
14M-0645016 Screw hex flange m6 x 1.0 x 16
1524-146-08 Plate, backing, no. 1 side
1624-100-02 Nut, plastic
1724-112-12 Spacer
1824-126-44 Bracket, breather separator
1924-445-02 Strap, breather
2M-0545016 Screw hex flange m5 x 0.8 x 16
2024-086-27 Screw
3SM-0645016 Screw hex flange m6 x 1.0 x 16
424-314-05 Guard, flywheel
524-146-11 Plate, backing, no. 2 side
6M-0545020 Screw hex flange m5 x 0.8 x 20
7M-0551016 Screw hex flange m5 x 0.8 x 16
824-063-28 Baffle, cylinder barrel, no. 2 side
924-063-23 Baffle, valley, no. 1 side
9924-100-01 Nut, plastic (3) (included with blower housing)
99A24-100-02 Nut, plastic (2) (included with blower housing)
99B25-139-16 Plug, button 9/16 (included with blower housing)
99C24-113-28 Decal, horsepower
1M-0839080 Screw
1012-239-01 Drive, pinion
1112-170-03 Armature, starter
212-098-03 Starter, solenoid shift (includes 4/18)
3M-0841080 Nut, hex flange m8 x 1.25
452-100-10 Nut, starter
552-435-02 Solenoid
652-100-09 Nut, starter
712-081-02 Drive, end cap
812-090-10 Lever, starter drive
924-755-84 Kit, starter repair
024-789-02-S Maintenance co kit
124-086-06 Screw, phillips hd. 11-16 x 3/4
1012-237-01 Clamp, cable
1124-126-47 Bracket, control
1224-144-11 Shaft, throttle
1324-126-17 Bracket, throttle shaft
1424-112-10 Spacer
1524-090-12 Lever, throttle control
1624-089-18 Spring, governor
17M-0641060 Nut, hex flange m6 x 1.0
18SM-0642025 Screw, hex flange m6 x 1.0 x 25
1924-090-14 Lever, governor
2M-0446030 Nut, hex m4 x 0.7
2025-158-11 Bushing, throttle linkage
2124-089-01 Spring, linkage
2224-079-04 Linkage, throttle
2325-158-08 Bushing, linkage retaining
24M-0645016 Screw, hex flange m6 x 1.0 x 16
2524-079-10 Linkage, choke
2625-158-11 Bushing, throttle linkage
27M-0647060 Nut, hex lock m6 x 1.0
28X-25-52 Washer, plain 1/4
2925-431-01 Spacer
3M-0647060 Nut, hex lock m6 x 1.0
3024-090-20 Lever, choke
31277341 Washer, spring 3/8
424-090-09 Lever, throttle control
5M-0401030 Screw, hex cap m4 x 0.7 x 30
6X-25-72 Washer, plain 1/4
724-089-20 Spring, throttle shaft
8M-0639016 Screw hex flange m6 x 1.0 x 16
9M-0545016 Screw hex flange m5 x 0.8 x 16
024-789-02-S Maintenance co kit
124-755-59 Kit, oil pan with gasket
1024-086-17 Screw, hex flange m8 x 1.25 x 45
1124-086-16 Screw, hex flange m8 x 1.25 x 45
1252-139-02 Plug, drain
1324-393-08 Oil pump assembly (includes 14)
1424-123-05-15 Tube, oil pickup
1512-144-02 Shaft, governor gear
1652-448-02 Tab, locking
1724-043-12 Kit, governor gear with pin (includes 18)
1812-380-01 Pin, governor regulating
19M-0645025 Screw, hex flange m6 x 1.0 x 25
224-086-12 Screw, hex cap m6 x 1.7 x 18
20M-0631005 Washer, plain 6mm
2125-162-07 Screen oil
2224-041-24 Gasket, oil pan
324-100-01 Nut, plastic
424-594-09 Oil cooler
524-136-03 Nipple, oil filter
612-050-01 Filter, oil
724-153-13 O-ring
8X-75-32 Plug, hex ctsk. 3/8
952-032-08 Seal, oil (pto end)
9924-422-03 Shim, thrust
99A24-113-25 Decal, oil cooler
0N/P Rpm settings: high speed: 3200-3400
024-789-02-S Maintenance co kit
124-041-02 Gasket, exhaust
2M-0829033 Stud, m8 x 1.25 x 33
3M-0841080 Nut, hex flange m8 x 1.25
9924-755-03 Gasket set
99A24-522-72 Short block
024-789-02-S Maintenance co kit
124-014-72 Crankshaft
252-139-09 Plug, cup
024-789-02-S Maintenance co kit
124-853-27 Carburetor with gaslet (incl. 2-4)
1024-393-04 Pump, fuel, pulse
1124-100-01 Nut, plastic
1224-353-03 Line, fuel, 10-5/8"
1325-050-03 Filter, fuel
1424-126-53 Bracket, throttle stop
15M-0259006 Screw throttle stop bracket
1A24-757-18 Overhall kit with gaskets
1B24-757-19 Choke repair kit with gaskets
1C24-757-20 Gasket repair kit
1D24-757-21 Accelerator pump with gaskets
1E24-757-22 Solenoid replacement kit with gaskets
224-041-15 Gasket, carburetor
324-053-27 Carburetor assembly (for information only, not ...
424-041-14 Gasket, air cleaner base
5X-426-9 Clamp, hose
625-353-03 Line, fuel, 13-1/2"
7M-0641060 Nut m6 x 1.0
8M-0629095 Stud m6 x 1.0 x 95
924-086-12 Screw, hex cap head