Home | Register Login | Wanted Manuals | MarketPlace | Members Area | Manuals Manufacturer Directory | UPC Lookup | Information Pages | Policy


Back To Craftsman Tractors-Riding-Lawnmowers       Model: 917.255741 or 917255741 Craftsman 12 HP 38 Inch Riding Lawn Tractor Mower
Regular Text Search or Search by Model Number

Register / log-in to add to your Hammerwall Collection.
Manual Location


This is a partial text extraction from the pdf, to download the pdf, click the Manual tab. If you want to search this text, hold control and F, and type the word you are looking for.

Page: 1

OWNERS MANUAL MODE L NO , 917 _ 255741 12 H . P . Caution : Read Rules for 38 " RIDING Safe Operations and Instruction LAWN TRAC TOR Carefully ELECTRIC START iAssemblyon Installat Operation Repair Parts Sears , Roebuck and Co , , Chicago , tL 60684 US A ,
Page: 2

CONGRATULATIONS on your purchase of a Sears Lawn Tractor It has been designed , engineered and manufactured MODE L to give you the best possible dependability and performance . NUMBER Should you experience any problem you cannot easily reme - SERIAL dy , please contact your nearest Sears Service DepartmenL NUMBER They have competent , well - trained technicians and the proper tools to service or repair this unit . THE MODEL AND SERIAL NUMBERS WILL BE FOUND ON THE MODEL PLATE ATTACHED TO Please read and retain this manual , The instructions will enable THE FENDER _ you to assemble , operate and maintain your TractoF properly . Always observe the " RULES FOR SAFE OPERATION " YOU SHOULD RECORD BOTH MODEL AND SERIAL NUMBERS AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE LIMITED TWO YEAR WARRANTY ON ELECTRIC START RIDING EOUIPMENT For two years from date of purchase , when this riding equipment is maintained , lubricated , and tuned up according to the operating and maintenance instructions in the owner's manual , Sears will repair free of charge any defect in material or workmanship in this electric start riding equip - ment . ' This warranty excludes blade ( s ) , blade adapter ( s ) , spark plug ( s ) , air cleaner ( s ) and belt ( s ) , which are expendable and become worn during normal use . This warranty does not cover : tire replacement or repair caused by punctures from outside objects ( such as nails , thorns , stumps , or glass ) ; and repairs necessary because of operator abuse or negligence , including the failure to main - tain the equipment according to instructions contained in the owner's manual ; and riding equipment used for commercial or ' rental purposes _ FULL 90 - DAY WARRANTY ON BATTERY For 90 days from the date of purchase , if any battery included with this riding equipment proves defective in material or ' workmanship and our testing determines the battery wilt not hold a charge , Sears will replace the battery at no charge , WARRANTY SERVICE IS AVAILABLE BY CONTACTING THE NEAREST SEARS SERVICE CENTER / DEPARTMENT IN THE UNITED STATES . , This warranty applies only while this product is in use in the United States , This warranty gives you specific legal rights , and you may also have other rights which vary from state to state _ . Sears , Roebuck and Co . , D / 698 - 731A , Sears Tower , Chicago , IL 60684 TABLE OF CONTENTS RULES FOR SAFE OPERATION . . . . . . . . . . . . . . . . 3 MAINTENANCE INSTRUCTIONS - MOWER . . . . . 12 ASSEMBLY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . 4 MAINTENANCE INSTRUCTIONS - TRACTOR . _ 14 OPERATION INSTRUCTIONS oTRACTOR . . . . . . . 8 TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . . . . . 21 OPERATION INSTRUCTIONS - MOWER . . . . . . . 11.2 - REPAIR PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Page: 3

FOR SAFE OPERAT O NARNING : This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest - covere6 , brush , covered or grass - covered land unless the engine's exhaust system is equipped with a spark arrestor meeting applicable Local or statelaws ( if any ) Ifasparkarrester is used . it should be maintained in effective working order by the operator tn the State of California the above is required by Iaw ( Section 4442 of the California Public Resources Code ) Other states may have similar laws Federal iaws apply on federat lands . See your Sears Authorized Service Center for spark arrester muffler part number 677V1 23 Use care when pulling loads or using heawyequipment , 1 . . Know the controls and how to stop quickly , READ eTHISd OPERATOR'S MANUAL and instructions furnish a _ Use only approved drawbar hitch points with attachments b Limit loadsto those you can safely control 2 . Do not allow children to operate the machine . Do not co Do not turn sharply Use care when backing allow adults to operate it without proper instruction . , do Use count _ erweight or wheel weights when suggestedin the owner s manual . 3 , Do not carry passengers . . Do not mow when children and others are around , 24 Watch out for traffic when crossing or near roadways 4 . AIways wear substantial footwear . Do not wear loose fitting 25 When using any attachments , never direct discharge ofe - material toward bystanders nor allow anyone near the v clothing that could get caught in moving parts . . hicle while in operation 5o Keep your eyes an _ mind on your tractor , mower and the area being cut . . Don t let other interests distract you ° 26 Handle gasoline with care it is highly flammable 6 . Do not attempt to operate your tractor or mower when a , Use approved gasoline containers not in the drivers seat . b , Never remove the fuel cap of the fuel tank or add gas - 7 . Always get on or off your tractor from the operators left oline to a running or hot engine or an engine that nhas - hand side , . not been allowed to cool for several minutes after ru 8 , Clear the work area of obiects ( wire , rocks , etc _ ) which ning , Never fill the tank indoors , always clean up spilled might be picked up and thrown , gasoline 9o Disengage all attachment clutches before attempting to c . Open doors if the engine is run in the garage - exhaust start the engine , fumes are dangerous . Do not run the engine indoors . 10 . Disengage power to att { chments and stop the engine be - 27 , Keep the vehicle and attachments in good operating con - fore leaving the operator s position dition , and keep safety devices in place and working . tio Disengage power to mower , stop the engine and kdisconnect - 28 . Keep al ! nuts , bolts and screws tight to be sure the equip = spark plug wire ( s ) from spark plug ( s ) before cleaning , ma ment is in safe working condition ing an adjustment or repairshments 29 Never store the equipment with gasoline in the tank inside 12 Disengage power to attac when transporting or not a building where fumes may reach an open flame or spark . in use . Allow the engine to cool before storing in any enclosure . 13 , Take all possible precautions when leaving the vehicle un - 30 To reduce fire hazard , keep the engine free of grass , leavesis attended . Disengage the power4ake - off , lower the attach - or excessive grease Do not clean product while engine merits , shift into neutral , set the parking brake , stop the runningt engine and remove the key ° 31 , Excep for adjustment ; DO NOT operate Engine if air 14 Do not stop or start suddenly when going uphill or down - cleaner or cover directly over carburetor air intake is re = • hill Mow up and down the face of slopes ( not greater than moved Removal of such part could create a fire hazard 15 ° ) ; never across the face Refer to page 43 32 Do not operate without a muffler or tamper with the 15o Reduce speed on slopes and make turns gradually to pre - exhaust system . Damaged mufflers or spark arrestors could vent tipping or loss of control Exercise extreme caution create a fire hazar & Inspect periodically and replace if when changing direction on slopes . necessary . 16o While going up or down slopes , place Gear Shift Control 33 The vehicle and attachments should be stopped and in - Lever in 1st gear position to negotiate the slope without spected for damage after striking a foreign object and the stopping damage should be repaired before restarting and operating 17o Never mow in wet or slippery grass , when traction is un - the equipment sureor at a speed which could causea skid 34 Do not change the engine governor settings or overspeed ! 8 Stay alert for holes in the terrain and other hidden hazards the engine ; severedamage or injury may result Keep away from drop offs , 35 _ When using the vehicle with mower , proceed as follows : 19o Do not drive too close to creeks , ditches and public high - a . Mow only in daylight or in good artificial light ways ° b . Shut the engine off when unclogging chute ° 20 , Exercise special care when mowing around fixed objectser c . Check the blade mounting bolts for proper tightness at in order to prevent the blades from striking them Nev frequent intervals . deliberately run tractor or mower into or over any foreign 36 . Do not operate the mower without the deflector shield in object , place 21 _ Never shift gears until tractor comes to a stop ° 37 . Disengage power to mower before backing up Do not mow 22 ° Never place hands or feet under the mower , in discharge in reverse unless absolutely necessary and then only after chute or near any moving parts while tractor or mower are careful observation of the entire area behind the mower running . Always keep clear of discharge chute , 38 Under normal usagethe grass catcher bag materiaf is subject to deterioration and wear It should be checked frequently for bag replacement Replacement bags should be checked to ensure compliance with the original manufacturer's recommendations or specifications PRECAUTIONS , IT MEANS - ATTENTION ! BECOME ALERTI LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY YOUR SAFETY IS INVOLVED * 3
Page: 4

To assemble your Tractor you will need : two 7 / 16 " wrenches , two 9 / 16 " wrenches , two 1 / 2 " wrenches , a 3 / 4 " wrench and a utility knife NOTE : RIGHT HAND ( R , H ) AND LEFT HAND ( LH . ) ARE DETERMINED FROM OPERATOR'S POSITION WHILE SEATED ON THE TRACTOR ASSEM6LY I , . Cut down carton at four corners , fold down carton , Re . UPPER move Bag of Parts , Remove tractor from skid , STEERING SHAFT 2 , Slide Upper Steering Shaft over Lower Steering Shaft until boil holes line up with slots in Lower Steering Shaft ( Fig , 1 ) , BOLTS 3 _ Use two Hex Bolts 3 / 8 - 16 x t . 1 / 4 and two Locknuts 3 / 8 - 16 to retain Upper Steering Shaft to Lower Steering Shaft Tighten securely . , 4o Stide Tube over Steering Shaft Assembly and over Steering Sleeve Bracket LOWER STEERING 5 _ Place Steering Wheel Adapter on Upper Steering Shaft , SHAFT 6 . With front wheels pointed straight ahead , place Steering SLEEVE Wheel on Steering Wheel Adapter - , Bars of Steering Wheel BRACKET should point straight across tractor , 7o Place 2 - 1 / 4 " Dia , Washer on Upper SteeringShaft and in - stall a 1 / 2 " Nut , Tighten securely , 8 Snap Insert into Steering Wheel , 9 Remove plastic on Tractor Hood FIGURE 1 SEAT iNSTALLATiON , Mount Seat Pivot Bracket to Fender using two Hex Bolts 3 / 8 - 16 x 3 / 4 , two Washers t3 / 32 x 3 / 4 x 10 Ga . and , two Crownlock Nuts 3 / 8 - 16 ( Fig , 2 ) . NOTE ; WASHERS _ SHOULD BE POSITIONED UNDER FENDER NEXT TO SEAT NUTS . Seat Pivot Bracket , Bolts , Washers and Nuts found in Bag of Parts ° Tighten Nuts securely . HEX BOLTS , WASHERS AND LOCK NUTS 2 . Mount Seat Pan to Seat Pivot Bracket using two Shoulder BOLT HE × SHOULDER BOLT BOlts 5 / 16 - 18 and two Lock Nuts 5 / 16 - 18 ( Fig . 2 ) ( head 5 / 16 - 18 & LOCK NUT 5t ! 6 - 18 & LOCK NUT of Bolts to outside ) _ Bolts and Lock Nuts found in Bag of FENDER SEAT Parts , Tighten Nuts secureFy , BRACKET 3 _ Place Seat on Seat Pan , . Screw Adjustment Bolts , Lock - / washers and Flat Washers into Seat ( Fig . 3 ) , Adjustment Bolts , Lockwashers and Flat Washers found in Bag of Parts , Tighten finger ' tight , FIGURE 2 4 _ Place Seat in operating position ° Sit on the Seat and press Clutch - Brake Pedal all , the way down . if operating position is not comfortable , adjust Seat , 5 . Raise Seat . Use 9 / t6 " wrench to loosen Adjustment Bolts ( Fig , 3 ) , When adjusted for ' comfortable operation , tighten Adjustment Bolts securel ¥ o J CLUTCH / BRAK E PEDAL / FIGURE 3 - 4 -
Page: 5

BATTERY ONSTALLATDON WEAR EYE AND FACE SHIELD . . CUT AWAY VIEW VENT CAP WASH HANDS OR CLOTHING IMMEDI - ATELY tF ACCIDENTALLY IN CONTACT WITH ELECTROLYTE ° BATTERY TUBE DO NOT SMOKE , FUMES FROM CHARG - ED ELECTROLYTE ARE EXPLOSIVE . BATTERY CELL 1 . Fill and charge Battery ( before installing ) , NOTE : SEE DETAILED iNSTRUCTIONS PACKAGED WITH BAT - TERY . FIGURE 4 ao Fill Battery with electrolyte to bottoms of tubes in cells ( Fig , 4 ) . NOTE : DO NOT OVERFILL . OVERFILLING WILL RESULT 1N DAMAGE TO TRACTOR . b . Check level of electrolyte after 30 minutes ° Add addi - SEAT tional electrolyte if necessary . NOTE : TIGHTEN VENT CAPS SECURELY _ c . Charge Battery at a rate not exceeding three amperes for about two and one half hours . do Neutralize excess electrolyte for disposal by adding it to four inches of water in a five gallon plastic contain - er . , Stir with a wooden or plastic paddle while adding baking soda until the addition of more soda causes no more foaming . FENDER DO NOT SHORT BATTERY TERMINALS . WELL BEFORE INSTALLING BATTERY , RE - MOVE METAL BRACELETS , WRIST - WATCH BANDS , RINGS , ETC . FROM YOUR PERSON , , POSITIVE NEGATIVE 2 Position Battery in tractor as foltows : BATTERY I BATTERY TERMINAL TERMINAL a . Lift Seat ( Fig . 5 ) , BATTERY b . , Lower Battery into Fender Wel ! with Battery Terminals FIGURE 5 toward front of tractor ( Fig , 5 ) , , Make sure Battery rests in Battery Tray ( Fig , , 6 ) . NOTE : BE SURE BATTERY DRAIN TUBE IS SECURE - LY ATTACHED TO BATTERY TRAY DRAIN . 3 . Connect Battery Cables using : two Hex Bolts , two Flat Washers , two Lockwashers and two Hex Nuts ( shown full size below ) found in Bag of Parts , POSITIVE TERMINAL MUST BE CON - NECTED FIRST TO PREVENT SPARKS FROM ACCIDENTAL GROUNDING a Connect RED Battery Cable to Positive ( + ) Battery Tero minal with Hex Bolt , Flat Washer . Lockwasher and Hex Nut ( Fig . 6 ) . Tighten securely . b . Connect BLACK Ground Cable to Negative ( - ) Battery Terminal with remaining Hex Bolt , Fiat Washer , Lock - washer and Hex Nut ( Fig ° 6 ) . Tighten securely ° - 5 -
Page: 6

4 , Install Battery using : two Int . / Ext Lockwashers , , two Wing WING Nuts ( shown full size below } and NUT INTERNALIEXTERNAL LOCKWASHE R TERMINAL GUARD WING q = D INTERNAL / EXTERNAL LOCKWASHER 0 \ BATTERY BOLT two Battery Bolts and one Terminal Guard found in Bag of Parts . ao Using the slot on one side of the Battery Support ( Fig . 6A ) slide Battery Bolt into Frame Slot ( head of Bolt down } . Fasten the Battery Bolt to the Terminal Guard using IntjExt ° Lockwasher and Wing Nut as shown in Fig . 6Ao b . Assemble the remaining Battery Bolt to other side of FIGURE 6A Battery Support and fasten Terminal Guard to it with re , maining Int , / E _ t _ Lockwasher and Wing Nut ° Tighten Wing Nuts securely by hand ( Fig . 6A ) . NOTE : USE TERMINAL ACCESS DOORS ( F tG . 6A ) FOR : 1 , Inspection for secure connections ( tighten hardware ) . 2 . inspection for corrosion , 3 , Testing battery , 4 , Jumping ( if required ) . 5 _ Charging ( if required ) . WHEN NOT IN USE , KEEP TERMINAL ACCESS DOORS CLOSED , NOTE : DO NOT START ENGINE UNTIL INITIAL SER - VICE HAS BEEN PERFORMED , INITIAL ADJUSTMENTS 1 . TIRE PRESSURE Reduce Tire pressure to t4 PSI in front tires ; 12 PSI in rear tires , ( Tires were overinflated for shippingL SCREW . HOOD / a . To raise Hood , lift at rear of Hood . FIGURE 7 b . Unsnap Headlight Connection ( Fig , 8 ) . c , . To remove Hood , Grill and Side Panels , raise Hood and loosen one screw on each Side Panel . ( The screw remains HEADLIGHT in the Side Panel ) ( Fig , 7 ) . _ CONNECTION d , Stand in front of Tractor _ Grasp Hood and titt forward and lift off ( Fig . 8 ) , e , To reinstall , reverse above procedure . . FIGURE 8 - 6 -
Page: 7

INaTIAL SERVnCE NOTE : BE CAREFUL NOT TO ALLOW DiRT TO ENTER THE ENGINE WHEN CHECKING OR ADDING OIL OR FUEL OIL FILLER I . , Open Hood . 2 . Check Engine Oil Leve ! with Tractor on level ground Re - move and wipe Dipstick ( Fig , 9 ) clean , screw it in tight for a few seconds , remove and read Oil Level if necessary , add FUEL Oil until " FUEL " mark is reached CAP RECOMMENDED SAE VISCOSITY GRADES L ! i , ! iiI ! ! . . z . . FUEL f . . s . w . . 2o0 . _ w3o ' TANK . . . . . . . " - - 4 1 : . . . . : . . . . . . . . . . I . . . , . . . I . . . t . i FIGURE 9 - 20 o 0 ° 32 ° 60 ° 80 ° 100 ° TEMPERATURE RANGE EXPECTED BEFORE NEXT OIL CHANGE ° ALL OILS MUST MEET A . P . L SERVICE CLAS - SIFICATION SD , SE , OR SF , . Capacity is 2 pints ° NOTE : DO NOT OVERFILL Dipstick assembly must be securely tightened into tube at all times when engine is operating . 3 . Fill Fuel Tank ( Fig . . 9 ) . Use fresh , clean , unleaded auto - motive gasoline ° ( Leaded " " " " Regular grade gasoline ts not an acceptable substitute ° Use of leaded gasoline wilt increase carbon and lead oxide deposits and reduce valve life ) . Capacity is 5 quarts . . WARNING : DO NOT USE GASOHOL OR METHANOL . These type fuels react with water content in the fuel and tend to form strong acids which can corrode metal parts and harm rubber and plastics . FILL TO BOTTOM OF GAS TANK FILLo ER NECK , DO NOT OVERFILL . WIPE OFF ANY SPILLED OIL OR FUEL , DO NOT STORE , SPILL OR USE GASOLINE NEAR AN OPEN FLAMEn - 7 -
Page: 8

CAUTION TO AVOID INJURY CHOKE I , Read owners manual , 2 , Know location and function of all controls ° FAST 3o Keep guards , safety shields and switches in place and work - ing , 4 . Remove objects that can be thrown by blades . . 5 . Do not mow when children and others are around . 6 _ Never carry chitdren or passengers , 7o Always look behind machine before backing , 8o Do not mow where machine can tip or slip , MOWERBLADE 9 , If machine stops going uphill , stop blade and back slowly CLUTCH " ENGAGED ' _ down , POSITION t0o Be sure blades and engine have stopped before placing " DISENGAGE D " hands or feet near the blades , POSITION HEADLIGHT 11 _ Remove key when leaving machine . PARKING BRAKE DO NOT ADD ADDITIONAL WEIGHT TO THROTTLE THE TRACTOR OTHER THAN THE OP - " tON TIONAL WHEEL WEIGHTS . EXCESSIVE _ CONTROL LEVER " DISENGAGED " WEIGHT MAY OVERLOAD AND DAM - POSITION AGE THE TRANSMISSION . / GEARSHIFT LEVER STARTING THE ENGINE _ I _ = CLUTCH ! BRAKE " CLUTCH " POSIT , ON " C LUTCH / BRAK E " 1 _ Disengage Mower Blade Clutch Lever ( Fig _ 10 ) _ POSITION FIGURE 10 _ " _ _ . 2 . Depress Clutch ! Brake Pedal fully . _ 3 . Place Gear Shift Lever in " NEUTRAL " position ( Fig . 10 ) o " _ LIFT LEVER 4 _ Move Throttle Controt Lever ( Fig . 10 ) to " FAST " detent , : _ / PLUNGER LIFT then to the right and upward for " CHOKE " position , At the " FAST " position the Lever has a stop . The stop is pro - vided so that you will know when you are at full throttle ttFASTt ' position and prevent over travel into choke posio tion , 5 _ Turn Ignition Key clockwise ( ( ' _ ) to " START " position and release Key as soon as engine starls ( Fig . 10 ) . tmmedi _ ately move Throttle Control Lever mid - way between " SLOW " " FAST " and positions . NOTE : DO NOT RUN STARTER CONTINUOUSLY FOR MORE THAN FIFTEEN SECONDS PER MINUTE . If Engine does not start after severalattempts , move Throttle Control Lever mid - way between " FAST " and " SLOW " FIGURE 11 positions , wait a few minutes and try again . OPERATION ALWAYS WEAR SUBSTANTIAL FOOT - NOTE : MOWER OPERATION IS LISTED ON PAGE tl . WEAR AND AVOID LOOSE FITTING CLOTHING THAT COULD GET CAUGHT IN MOVING PARTS . THIS TRACTOR IS EQUIPPED WITH INTERLOCK SWITCHES TO PREVENT STARTING OF THE TRACTOR ENGINE WHILE THE MOWER BLADE CLUTCH LEVER IS IN THE " ENGAGED " POSI - TION AND / OR THE FOOT PEDAL IS NOT FULLY DEPRESSED . IMMEDIATELY WARMING UP THE ENGINE REPLACE SWITCHES THAT ARE NOT Move Throttle Control Lever mid - way between " FAST " and IN PROPER WORKING ORDER . DO NOT " SLOW " positions ( Fig , 10 ) . As engine warms up , move Throt - ATTEMPT TO DEFEAT THE PURPOSE tle Control Lever to " FAST " position , NOTE : ALLOW EN - OF THESE SWITCHES ° GINE TO WARM UP FOR A FEW MINUTES BEFORE OPERATING . LEARN TO START , STOP AND REVERSE YOUR TRACTOR IN A LARGE , OPEN AREA When restarting a warm engine move Throttle Control Lever 11 $ ' _ • 11 , t r to FAST poszt4on , CHOKE may not have to be used , - 8 -
Page: 9

MOWER INSTALL . ATnO _ CLUTCH PARAt LEL RETAINER ROD RETAINER LINK FRONT SPRINGS Your 38 " Mower installs without the use of tools Raise Lift AXLE SPRING CLUTCH _ ' _ Lever ( Fig ° 11 ) to its highest position . Turn Depth Adjust - ment Knob to lowest position ( Fig 14 ) BRACKET ! o Instal ! Front Hinge Pin through Axle and Parallel Link ( Fig . 12 ) . Secure with Retainer Spring ° 2 Install Rear Hinge Pin through Mower Lift Brackets and Parallel Link ( Fig , 12 ) Secure with Retainer Spring 3 Install Clutch Rod in Clutch Lever ( Fig , 13 - Inset ) , FRONT 4 . Move Lift Lever ( Fig , 11 ) forward to lower Suspension HINGE Arms , Stide Trunnions through Lift Bracket holes and PiN REAR secure with Retainer Springs ( Fig . 13 ) HINGE P _ N FIGURE 12 5o Roll Belt over Mower Drive Pulley Make sure Belt is inside Belt Guides ( Fig . 14 ) , See Belt Drive Schematic Decal on Mower Housing CLUTCH LEVER 6 , Use Lift Lever ( Fig _ t ! ) to raise mower CLUTCH . ROD NOTE : SEE MOWER ADJUSTMENT , BELOW , 7 , Turn Depth Adjustment Knob clockwise ( ( ' _ , ) to the mid - die of it's travel _ SUSPENSION ARM RETAINER SPRING MOWER ADJUSTMENT FOR ANY ADJUSTMENTS , INSPECTION OR MAINTENANCE : PUSH TRACTOR CLUTCH - BRAKE PED - AL COMPLETELY INTO BRAKE POSI - TION , , MOVE GEAR SHIFT LEVER TO " N " NEUTRAL POSITION , PLACE PARK - RETAINER LIFT ING BRAKE IN " ENGAGED " POSITION . SPRING BRACKET SHUT OFF THE ENGINE . PLACE MOWER BLADE CLUTCH LEVER IN " ENGAGED " TRUNNION FIGURE 13 POSITION , , MAKE ABSOLUTELY SURE THE BLADES AND ALL MOVING PARTS HAVE COMPLETELY STOPPED , RE - MOVE THE IGNITION KEY , DISCON - MOWER NECT THE SPARK PLUG WIRE FROM DRIVE THE SPARK PLUG AND KEEP WIRE \ 3ELT PULLEY AWAY FROM THE PLUG TO PREVENT \ INJURY FROM ACCIDENTAL START - ING . NOTE : BEFORE CHECKING THE SIDE TO SIDE AND FRONT TO REAR ADJUSTMENTS , PAGE 10 , BE SURE PRESSURE IN FRONT TIRES IS 14 PSi AND PRESSURE IN REAR TIRES IS 12 PSI IF TIRES ARE OVER OR UNDER INFLATED YOU WILL NOT PROPERLY ADJUST YOUR MOWER , DEPTH ADJUSTMENT Adjustm # nt for mower height is made with the Depth Adjust - ment Knob , Raise Mower cutting height by turning Depth FIGURE 14 Adjustment Knob clockwise ( _ ) Lower Mower cutting height by turning Depth Adjustment Knob counterclockwise - 9 -
Page: 10

LEVEL MOWER FROM SIDE TO SiDE LIFT SEE MOWER ADJUSTMENT , PAGE 9 . PLUNGER t _ Park tractor on level surface _ Depress Lift Lever Plunger LIFT and use Lift Lever to raise mower to maximum cutting LEVER height , SI DE - TO - SI DE : 3JUSTMENT , Measure height of Top of Flange to level surface at front of , It _ t TOP OF mower . D _ stance A should be the same ( Fig . I5 ) o TOP OF FLANGE FLANGE m If distance " A " needs to be changed , snap out AccessHole Cover on LHo side above Footrest . Use 9 / 16 " wrench on Nuts " B " and " C " at Side - To - Side Adjustment Trunnion ( Fig 16 ) , A A 4 _ To raise left side of mower , loosen Nut m * Bma ' nd tighten FIGURE 15 Nut " Ctl _ e To lower left side of mower , loosen Nut " C " and tighten Nut " B'o NOTE : ONE ROTATION OF ADJUSTMENT NUTS IS EQUIVALENT TO APPROXIMATELY 3 / 16 " HEIGHT CHANGE , . Be sureall nuts are securely tightened ° NOTE : SEE MOWER ADJUSTMENT , FRONT - TO - REAR , SIDE - TO . SIDE BELOW _ ADJUSTMENT TRUNNION ADJUST MOWER FROM FRONT TO REAR FIGURE 16 , To obtain the best cutting results , your Mower Housing should be adjusted so the Front and Rear Flange distance " D " ( Fig _ 17 ) is 5 / 16 " lower in front when the mower is REAR positioned in the hinhest cutting position . _ NOTE : MEAS - SUSPENSION URE DISTANCE _ XD _ FROM SURFACE TO RIGHT ARM \ REAR FLANGE AND COMPARE TO DISTANCE " D " AT RIGHT FRONT FLANGE ° 2 , To raise rear of mower , loosen Nut " E " on both Rear SuE - pension Arms . Screw both Nuts " F " up EQUAL NUMBER i _ REAR OF TURNS ( Fig = 18 ) _ / FLANGE 3 . When distance " D " is 5 / 1B " lower at front than rear , tight _ en Nut " E'o D 4 . To lower rear of mower , loosen Nut " F " on both Rear Suspension Arms an EQUAL NUMBER OF TURNS ( Fig . 18 ) . REAR FRONT LIFT SUSPENSION FLANGE BRACKET TRUNNION 5 _ When distance S'D " is 5t16 " lower at front than rear , re = tighten Nuts _ ' E ' . FIGURE 17 NOTE : WHEN ADJUSTING REAR SUSPENSION TRUN - NIONS , ALWAYS ADJUST BOTH EQUALLY SO MOWER WILL STAY LEVEL . REAR NUT SUSPENSION ARM REAR SUSPENSION LIFT TRUNNION BRACKET NUT " F " FIGURE 18 . 10 -
Page: 11

OPERATUO = MOWER MOWER CLUTCH LEVER ' * DISENGAGED " POSITION READ THE " RULES FOR SAFE OPERA - MOWER CLUTCH LEVER DEPTH " ENGAGED " POSITION TION " CAREFULLY BEFORE OPERAT - ADJUSTMENT ING YOUR MOWER , KNOB LIFT LEVER LtFT THE MOWER MUST BE ADJUSTED PROPERLY FROM LEVER FRONT TO REAR AND LEVELED FROM SIDE TO StDE BEFORE OPERATING , , THtS IS NECESSARY FOR LEVEL AND EFFICIENT MOWING REFER TO PAGE 10 1 . Place Mower Blade Clutch Lever in " DISENGAGED " position ( Fig . 19 ) 2 , Push tractor Clutch - Brake Pedal fully into brake position 3 , Place Gear Shift Lever in _ ' NEUTRAL " position NOTE : TRACTOR MUST HAVE FOOT PEDAL DEPRES - SED AND MOWER BLADE CLUTCH LEVER IN " DIS - ENGAGED " POSITION BEFORE TRACTOR W1LL START 4 , Start tractor and set engine speed to about 1 / 3 to 1 / 2 throt - tle before engaging mower , After mower is " ENGAGED " _ ARGE and you have started forward travel , set to FULL THROT - GUARD TLE , NOTE : " ENGAGE " OR " DISENGAGE " MOWER BLADE CLUTCH LEVER SLOWLY , FIGURE 19 NEVER " ENGAGE " MOWER EXCEPT WHEN SITTING ON TRACTOR SEAT . , NOTE : ALWAYS MOW WITH THROTTLE CONTROL IN f " FAST " POSITION . THIS RESULTS IN BETTER GRASS CUT , BETTER ENGINE COOLING , AND BETTER FUEL ECONOMY ° T 5 , Use Lift Lever to iower mower into cutting position Start mowing in the first gear and increase ground speed as conditions will permit . Average cutting height is approxi - mately 2 - t / 2 to 2 - 3 / 4 inches , Height of cut can be adjust - ed by means of the Depth Adjustment Knob ( Fig ° 19 ) Moving the Knob clockwise ( _ ) raises the mower ( Fig . t4 - Inset ) . . Moving the Knob counterclockwise ( _ ) lowers the mower . 6 Drive so that clippings are discharged onto the area that has been cut , Have the cut area to the right of the machine FIGURE 20 This will result in a more even distribution of clippings and more uniform cutting . , When mowing large areas ( Fig , 20 ) start by turning to the right so that the clippings will be discharged away from shrubs , fences , driveways , etc After two or three rounds , mow in the opposite direction making left hand turns until finished , if grass is extremely tall , it should be mowed twice The first time cut relatively high . The second time to the desired height . The felt hand side of mower should be used for trimming , FLQP = UP DUSCNARGE GUARD Your mower has a flip - up Discharge Guard ( Fig . 19 ) for door or gate clearance when held in raised position MAKE SURE MOWER BLADE CLUTCH LEVER tS IN " DISENGAGED " POSITION AND BLADES HAVE STOPPED BEFORE RAISING DISCHARGE GUARD ( DEFLEC , TOR ) , NEVER OPERATE MOWER WITH - OUT DISCHARGE GUARD IN OPERAT - ING POSITION , , - ! I -
Page: 12

When grinding , care should be taken to maintain blade bal - ance and the blade should be checked for proper balance before reinstatlation on mower , Unbalanced or bent blade will cause excessive vibration when running , and eventual damage to mower or engine Replace bent , damaged or un - balanced blades , MANDREL ASSEMBLY To check Blade balance , drive a nail into a beam or wall . Leave about one inch of the straight nail exposed . Place Center Hole of clean Blade over the head of the nail ( Fig , 22 ) . NOTE : CENTER HOLE OF BLADE ON NAIL IF BLADE tS PROPERLY BALANCED , BLADE SHOULD _ _ i FLANGES REMAIN IN POSITION SHOWN IN FIG 22 . IF EITHER END OF THE BLADE MOVES DOWNWARD , BLADE IS NOT BALANCED AND MUST BE REPLACED . 2 To ensure satisfactory operation , it is recommended that before the start of each mowing season , the old blades be LOCKWASHER _ _ discarded and replaced with new blades . Mower blades can . ExeOLT / be purchased at any Sears Service Center / Departments and most Sears Retail Stores = FIGURE 21 DAI LY MAI NTENANCE Make sure all nuts on bolts are tight and cotter pins and retain , , er springs are secure ° Keep blades sharp . Observe all safety pre - J ! I CENTER I | ' HOLE cautions Keep mower well lubricated ( refer to page 22 } , t . . . . . . . . . . . / . . . i . . . . . . CLEANING MOWER DISCONNECT SPARK PLUG WIRE TO PREVENT ACCIDENTAL STARTING BE - FORE CLEANING . FIGURE 22 Water - pressure from a garden hose will remove fresh clippings from underside of mowen Clean mower after each mowing _ MAINTENANCE = MOWER BLADE REPLACEMENT FOR ANY ADJUSTMENTS , INSPECTION Raise Mower to highest position to permit access to Blades _ OR MAINTENANCE : 1 _ Remove Bolt , Lockwasher and Washer ( Fig . 2 ! ) ( turn PUSH TRACTOR CLUTCH = BRAKE PED - counterclockwise ( f ' _ } _ AL COMPLETELY INTO BRAKE POSI - TION , PLACE PARKING BRAKE IN 2 . Place new Blade between Flanges , ( the word " TOP " is " ENGAGED " POSITION . MOVE GEAR stamped on all Blades to assure proper installation ) , and SHIFT LEVER TO " NEUTRAL " POSI - secure with Washer , Lockwasher and Bolt previously re - TION , PLACE MOWER BLADE CLUTCH moved , TIGHTEN SECURELY . . LEVER IN " DISENGAGED " POSITION . TURN IGNITION KEY TO " OFF " POSI - TION . MAKE ABSOLUTELY SURE THE BLADES AND ALL MOVING PARTS ALWAYS USE GRADE 5 HEAT TREATED HAVE COMPLETELY STOPPED , RE - BOLTS TO ATTACH BLADES , CHECK BOLTS IN BLADES OCCASIONALLY TO MOVE THE IGNITION KEY , DISCON - NECT ' THE SPARK PLUG WIRE FROM MAKE SURE BOLTS ARE TIGHT ° TOR - THE SPARK PLUG AND KEEP WIRE QUE BOLTS 30 - 35 FTo LBS _ AWAY FROM THE PLUG TO PREVENT INJURY FROM ACCIDENTAL STARTING ° A GRADE 5 HEAT TREATED BOLT CAN BE IDENTIFIED BY THREE BLADE CARE LINES ON THE BOLT HEAD AS For best results mower blades must be kept sharp , The blades SHOWN AT LEFT ° can be sharpened with a few strokes of a file or on a grinding wheel ° We suggest they be sharpened after every 15 hours of mowing , Do not attempt to sharpen while on mower , _ 12 _
Page: 13

TRACTOR OPERATION LEVER PLUNGER 1 , Depress Lift Lever Plunger at top of Mower Lift Lever and MOWER LIFT LEVER move Lever rearward to its " HIGHEST " position ( Fig " HIGHEST - POSITION 23 ) . 2 , With engine running and warm , place Throttle Control Lever midway between " FAST " and " SLOW " position 3 , Move Gear Shift Lever to " 1ST " Gear ( Fig 24 ) \ 4 _ Release Clutch - Brake Pedal SLOWLY to start forward movement , 5 , tf ground travel is too slow , move Throttle Control Lever " * LOWEST " to AST posltmon or press Clutch - Brake Pedal to stop POSITION and shift to a different gear . NOTE : ALWAYS SELECT A GROUND TRAVEL SPEED THAT WILL SUIT THE TERRAIN AND THE ATTACHMENT BEING USED , NEVER CHANGE GEARS WHILE TRACTOR IS MOV - FIGURE 23 ING . MAKE SURE PARKING BRAKE WILL HOLD TRACTOR SECURE NEVER PLACE YOUR HANDS OR FEET IN OR UNDER ANY POWERED ATTACH - MENT OR NEAR ANY MOVING PART PARKING WHILE TRACTOR OR ANY POWERED BRAKE ATTACHMENT IS RUNNING , " ENGAGED ' " ' ION NOTE : ALWAYS OPERATE ENGINE AT FULL THROTTLE " DISENGAGED " " CLUTCH " POSITION WHEN MOWING TO ASSURE BETTER MOWING PER - POSITION FORMANCE , LONG ENGINE LfFE AND PROPER DIS - CHARGE OF CUT MATERIAL REGULATE GBOUND SPEED BY SELECTING A LOW ENOUGH GEAR ( FIG , 24 ) TO GtVE THE MOWER CUTTING PERFORMANCE PLUS QUALITY OF CUT DESIRED I GEARER / OUT THE DEFLECTOR SHIELD ( DIS - CLUTCH / BRAKE , , _ LEV . f _ DO NOT OPERATE THE MOWER WITH - CHARGE GUARD ) IN PLACE , " CLUTCH / BRAK E ' > ' " DRIVE " _ / . _ POSITION " _ POSITION 7 - FIGURE 24 STOPPING YOUR TRACTOR I Push ClutchoBrake Pedal completely into " BRAKE " posi - TRACTOR OPERATOON ON NIILLS tion , 2 , Move Gear Shift Lever to _ ' NEUTRAL " position , • . It II . , , 3 , Place Parking Brake m ENGAGED position = Raise Park - WITH SLOPES GREATER THAN 1 ing Brake Lever and hotd in " ENGAGED " position ( Fig , DO NOT DRIVE UP OR DOWN HILLS AND DO NOT DRIVE ACROSS ANY 24 ) , Release Clutch - Brake Pedal SLOPE , REFER TO PAGE 43 . CLUTCH - BRAKE PEDAL SHOULD RE - MAIN COMPLETELY DEPRESSED WHEN t Move Gear Shift Lever to " 1ST " Gear before starting up or FOOT PRESSURE IS RELEASED , down hills . 2 , AVOID STOPPING OR SHIFTING ON HILLS a , If slowing is necessary , move Throttle Control Lever to 4 Move Throttle Control Lever to " SLOW " position slower position 5 Disengage Mower Blade Clutch Lever 6 Turn Ignition Key to " OFF " position LEAVE ENOUGH ROOM WHEN STOP - REMOVE KEY WHEN LEAVING TRAC - SLIGHT TRACTOR ROLL DOWNHILL TOR TO PREVENT UNAUTHORIZED PING AND STARTING TO ALLOW AS CLUTCH - BRAKE PEDAL MOVES USE . THROUGH CLUTCH POSITION BRING TRACTOR TO COMPLETE STOP BEFORE SHIFTING GEARS b . If stopping is absolutely necessary , push Clutch - Brake Pedal quickly to brake position and engage Parking Brake = TRANSPORTIING YOUR TRACTOR c . , To restart tractor movement , make sure tractor is in the II ti For pushing or towing your tractor , place Gear Shift Lever lowest speed range ( 1ST Gear ) and that you have allowed room to roll slightly downhill . Depress Clutch - in " NEUTRAL " plosition ( Fig 24 ) Push Clutch - Brake : Pedal Brake fully , Disengage Parking Brake and release Clutch - down firmly to DISENGAGE Parking Brake ( Fig . - ' 2 ; _ } : Brake Pedal SLOWLY to start tractor movement . NOTE : DO NOT TOW YOUR TRACTOR FASTER THAN 3 , , Make all turns gradually - 13 - S ! X MILES PER HOUR _
Page: 14

STARTING YOUR TRACTOR WtTN MAINTENANCE = TIRACTOR . A LOW BATTERY MOWER MAINTENANCE iS LISTED ON PAGE t2 , To keep your tractor running better longer ; perform neces - if your " Battery is too tow to start the engine , it should be sary service using the following Maintenance Schedule recharged , If " Jumper Cables " are used for emergency starting follow this procedure NOTE : YOUR TRACTOR IS EQUIP . - PED WITH A 12 VOLT NEGATIVE GROUNDED SYSTEM , F _ EFER TO " STOPPING YOUR TRAC - THE OTHER VEHICLE MUST ALSO BE A 12 VOLT NEGA - TOR " PAGE 13 AND DISCONNECT TIVE GROUNDED SYSTEM SCPIDAERNKTALPLUSGTARWTIIRNEG TBOEFPORREEVEMNATKINAGC . LEAD - ACID BATTERIES GENERATE EX , . ANY INSPECTION , ADJUSTMENT OR REPAIR ( EXCEPT CARBURETOR ) , PLOSIVE GASES . KEEP SPARKS , FLAME , AND SMOKING MATERIALS AWAY FROM BATTERIES . ALWAYS WEAR EYE PROTECTION AROUND BATTERIES , BAILY MAINTENANCE 1 Connect each end of the RED Cable to the POSITIVE ( + ) Make sure all nuts on bolts are tight and cotter pins and terminals of each battery ( taking care not to short against retainer springs are secure Observe all safety precautions , chassis ) , Keep tractor well lubricated ( refer to page 22 ) 2 Connect one end of the BLACK Cable to the NEGATIVE ( , - ) terminal of futIy charged battery 3 . Connect the other end of the cable to ENGINE BLOCK FIRST _ HOURS or good CHASSIS GROUND on tractor ( away from Gas Tank or Battery ) I , CHANGE ENGINE OIL 4 , Disconnect cables in reverse order : Changing Oil after the first two hours will help eliminate a Engine Block or chassis of tractor break - in residue which might be damaging to your " Engine b . Negative terminal of fully charged battery , NOTE : BE CAREFUL NOT TO ALLOW DIRT TO ENTER c , Positive terminals THE ENGINE WHEN CHANGING OIL . a Drain Oil with Engine warm Loosen Oil Drain Wing Nut ( Fig . 25 ) and remove Dipstick . Catch Oil in a suit _ . TERY TO START OTHER VEHICLES , _ l DO NOT USE YOUR TRACTOR BAT . . able container . Tighten Oil Drain Wing Nut b , Refill Engine Oil . See oil chart , page 7 . Refill capacity is 2 pints . NOTE : DO NOT OVERFILL . Replace Dipstick FREOUENTLY AIR SCREEN 1 . CHECK BATTERY a Electrolyte solution tevet in each Battery CelI should be even with bottoms of tubes in cells ( Fig . 261 . Add dis = tilled water if necessary NOTE : DO NOT OVERFILL b Keep Battery and Terminals clean c . Keep Battery Bolts tight , d Keep Vent Caps tight and small Vent holes in Caps open , e Recharge SLOWLY at 3 amperes if necessary . FUEL FILLER 2 , CHECK TIRE PRESSURE CAP Tire pressure in front Tires should be t4 PSI ; rear Tires 12 PSI 3 , CLEAN AIR SCREEN Air Screen ( Fig . 25 ) must be kept free of dirt and chaff to prevent Engine damage from overheating . / / OIL DRAI wING NUT FIGURE 25 CUT AWAY VIEW VENT CAP • BATTERY FIGURE 26 - 14 -
Page: 15

4 , CHECK BRAKE OPERATION This tractor is equipped with an adjustable brake system mounted on the right side of the transaxle ( Fig . , 27 ) . BRAKE JAM NUT OPERATING ARM tF TRACTOR REQUIRES MORE THAN BRAKE ROD \ 0 . . . . . . . . SIX FEET STOPPING DISTANCE tN HIGHEST GEAR , THEN BRAKE MUST BE ADJUSTED , , NOTE : PARKING BRAKE MUST BE DISENGAGE D ANDG GEAR SHIFT LEVER IN NEUTRAL WHILE MAKIN 1.1 / 2 - ADJ USTM ENT . , ao Depress Clutch - Brake Pedal and engage Parking Brake ° 0 bo Measure distance between Brake Operating Arm and Nut " A " on Brake Rod . . I ) O , CBBAK c . if distance ts other than 1 - 1 / 2 , loosen Jam Nut ( Fiq . • is t _ . , / 3 27 ) and turn NUt A untd d _ stance becomes t - 1 / 2 . * irl j Retighten Jam Nut aga nst Nut A , , Road test tractor for proper stopping distance as stated above . . Readjust if necessary = F1GURE 27 G3 DAILY OR EVERY HOURS ENGINE OIL AIR FILLER CAP COVER CHECK ENGINE OIL LEVEL AND DIPSTICK \ DO NOT CHECK ENGINE OIL LEVEL WITH ENGINE RUNNING . Several minutes after stopping Engine , check Engine Oil FOAM Level with Tractor on level ground , , Remove and wipe Dip - ELEMENT stick clean ( Fig , 29 ) , screw it in tight for a few seconds , re - move slowly and read Oil level . If necessary , add Oil until " FULL " mark is reached DO NOT OVERFILL 6vs.v . = . . s AIR ( OPERATING IN DUSTY CONDITIONS MAY REQUIRE CLEANER MORE FREQUENT SERVICING ) BODY 1 . CLEAN AIR CLEANER ELEMENT ( FIG . 28 ) ao Open Hood , b . Snap off Air Cleaner Cover ° FIGURE 28 c , . Remove Foam Element from Air Cleaner Body . d . Wash Foam Element in liquid detergent and water to remove dirt . . eo Wrap foam in cloth and squeeze dry . f _ Saturate foam in clean engine oil Squeeze to remove excessoil = g , , Replace Foam Element and snap Cover on Air Clean - er Body , NOTE : NEVER RUN ENGINE WITH AIR CLEANER RE - MOVED . 2 . CHANGE ENGINE OIL The best time to change Engine Oi { is at the end of a day's operation when all dirt and foreign materiafs are suspended in the hot Oii _ See oil chart , page 7 - 15 -
Page: 16

3 . CLEAN ENGINE COOLING FINS Keep Engine Cooling Fins free of dust , dirt and oil to pre - vent Engine damage from overheating . AIR CLEANER COVER _ " _ - - _ _ a . Snap Cover off Air Cleaner ( Fig . 29L Remove Hex Head Screw from inside Air Cleaner . Remove two SCREW _ , Slotted Head Screws from rear of Air Cleaner . Pull Air k Cleaner ' off . BLOWER b , Remove two Hex Head Screws from front of Blower HOUSING SCREW % SCREW Housing _ Remove two Hex Head Screws from side of Blower Housing _ co Pull Blower Housing off . Cytinder Head Cover may also be removed ° Clean Engine Cooling Fins with a stiff bristled brush or compressed air ' _ . HEX HD WEAR SAFETY GLASSES IF USING COM - SCREW PRESSED AIRo COOLING d . To reassemble , reverse above procedure , HEX HD FINS SCREW NOTE : PRESS BREATHER TUBE INTO BOTTOM OF AIR CLEANER ( FIG . 29 ) . CYLINDER 4 . MUFFLER HEAD N COVER Do not operate the tractor without a Muffler or tamper with the exhaust system _ DO NOT TOUCH HOT MUFFLER , CY - PLUG LINDER OR FINS AS CONTACT MAY CAUSE BURNS , Periodically clean the muffler area to prevent grass , dirt and combustible material from accumulatingo Damaged Mufflers or spark arresters could create a fire hazard , , In , , spect periodically and replace if necessary , , tf your engine is equipped with a spark arrester screen assembly , remove every 50 hours for cleaning and inspection , , Replace if damaged ° FIGURE 29 fv = . vt ] @ @ . oo . s 1 . REPLACE SPARK PLUG Change the spark plug after every 100 hours of operation or at the beginning of each mowing season ° A Deep Well 13 / 16 _ socket is required to remove the Spark Plug . Set the Spark Plug gap at = 030 inch ( Fig , 30 ) . FIGURE 30 2 . REPLACE AIR CLEANER ELEMENT - 16 -
Page: 17

ASNEEDED PLATE 1 . CARBURETOR ADJUSTMENT % & DO NOT MAKE UNNECESSARYADJUSTMENTS FAC - TORY SETTINGS ARE SATISFACTORY FOR MOST APPLICATIONS AND CONDITIONS . tF ADJUSTMENTS ARE NEEDED , PROCEED AS FOLLOWS : THROTTLE a , Make sure Air Cleaner is clean ( see page 15 ) , LEVER THROTTLE CABLE b , , With engine not running , place Throttle at " FAST " * f ' i ' . * detent ( not m CHOKE position ) ° CLAMP SCREW C . Check that hole in Throttle Lever and hole in Plate line up ( Fig . 31 - Inset ) , If holes are not aligned , loosen Clamp Screw and move Throttle Cable until holes are aligned , Tighten Clamp Screw , d . Turn High Speed Adjusting Needle clockwise ( _ ) , clos - ing finger tight ONLY , and then turn counterclockwise | DLESPEEO ( t _ ) t - 1 / 2 turns ( Fig . 31 ) _ STOPSCREW . / e , Turn Idle Adjusting Needle clockwise ( ( ' _ ) closing finger tight ONLY , and then turn counterclockwise ( _ ) I turn . REFER TO " STARTING THE ENGINE " , PAGE 8 . FUEL LINE CLAMP f , Start Engine and allow to warm for five minutes , g , Make final adjustments with Engine running , Gear Shift Lever in " NEUTRAL " position and Parking Brake en - gaged , IDLE - - With Throttle Control Lever in " FAST " position , ADJUSTING turn High Speed Adjusting Needle counterclockwise NEEDLE ( f _ ) until engine runs rough " then turn clockwise _ , l FUEL ( F - _ ) until engine begins to miss , Turn Needle to a FILTER / point midway between these positions , HIGH SPEED - - With Throttle Control Lever in " SLOW " position , ADJUSTING NEEDLE hold Throttle Lever so that Idle Speed Adjusting Screw is against Carburetor , turn Idle Adjusting FIGURE 31 Needle counterclockwise ( f - _ ) until engine runs ' _ rough " and then turn clockwise ( f " _ ) until engine begins to die . Turn Idle Needle to a point midway between these positions . , NOTE : If enqine hesitates when moving Throttle Control tt _ . ' 1 It 1 , Lever from SLOW to RUN position , turn Idle Speed Adjusting Screw counterclockwise ( t ' - _ ) one - eighth turn . , 2 , , REPLACE FUEL FILTER a , Remove Clamps from fuel lines at front and rear of Fuel Filter ( Fig , 31 ) o b , PUll Fuel Filter out of fuel lines , c . Install new Fuel Filter with arrow pointing toward engine , do Ii ] stal ! new Fuel Line Clamps supplied with Fuel Filter ° BE SURE THERE ARE NO FUEL LINE LEAKS AND THAT FUEL LINE IS IN PROPER POSITION IN HOSE CLAMPS t7 -
Page: 18

REPLACE TRACTOR MOTION DRIVE BELT BELT The tractor Drive Belt may be replaced without tools , Park the tractor on level area , Engage Parking Brake , NOTE : TRANSAXLE BELT INSTALLATION DECAL UNDER LEFT FOOT - PULLEY REST . a , Remove mower . ( See Mower Section , page 20 ) . b . Remove two Retainer Springs from Belt Guide Bracket below Transaxte Pulteyo Remove Bracket ( Fig . 32 ) , . c Swing Belt Guides away from Belt , toward rear of trac - tor ( Fig 32 ) d Roll Belt over top of Transaxle Pulley e Roll Belt over Engine Pulley and off idler IFig 34 ) . f Release Parking Brake Pull Belt as far as possible over top of Clutch Pulfey g Reset Parking Brake ° Pull Belt over top of Clutch Putley ( Fig 34 ) h Pull Belt out through Shift Gate to remove from tree , tor ( Fig 33 ) Install Belt by reversing above procedure , NOTE : RE fl RETAINER PLACE ONLYWlTH BELT LISTED IN MANUAL , BELT GUIDE RETAINER SPRING BRACKET SPRING 4 . CLEAN BATTERY AND TERMINALS FIGURE 32 Corrosion and dirt on the Battery and Terminals cause the Battery to = _ leak " power LEAD - ACID BATTERIES GENERATE EX - PLOSIVE GASES , KEEP SPARKS , FLAME , AND SMOKING MATERIALS AWAY FROM BATTERIES ALWAYS SHIELD YOUR EYES AROUND BATTERIES , a Disconnect BLACK Battery Cable then RED Battery Cable and remove Battery from Tractor Wash Battery with four tablespoons of bak ; ng soda to one gallon of water . NOTE : BE CAREFUL NOT TO GET THE SODA SOLUTION INTO THE CELLS . Rinse the Battery with plain water , dry and reinstall on Tractor b , Clean Terminals and Battery Cable ends w : th a w : re brush unti ! bright , Replace Battery Cables , connecting RED Battery Cable to Pos ; tlve Term ; nal f rst ; hen BLACK Battery Cabie to Negat ve Term ha ! , Coat tet , . minal connections with VasoFne : SHIFT GATE FIGURE 33 ENGINE PULLEY / DRIVE BELT SCHEMATIC CLUTCH PULLEY L . H . SIDE BELT GUIDE REAR VIEWED FROM BOTTOM OF TRACTOR FIGURE 34 - 18 -
Page: 19

5 . TIRE CARE a . Maintain tire pressure in front tires at 14 PSi and rear tires at 12 PSi KL1P RING b Keep tires free of gasoline , oil . or insect control chemio cals which can destroy rubber c Avoid stumps , stones , deep ruts and other hazards that may cause tire damage d . Removing front wheel for tire repair ( Fig . 35 ) - - Block up front axle securely ° Puit off Dust Cap . - - Remove Klip Ring and Washer and remove wheel ° DUST - - Repair tire and reassembfeo Replace Washer , snap CAP Klip Ring securely in axle groove , RepIace Dust Cap e Removing rear wheel for tire repair ( Fig 36 ) . . - - Block up rear axle securely . P011 off Dust Cap - - Remove E - Ring and Washers ( 1 to 3 as required ) and FIGURE 35 remove wheel - - Repair tire and reassemble , Replace Square K . ey in Axle Shaft . - Replace Washers , E - Ring and Dust Cap BE SEATED . OVERINFLATION CAN WHEN MOUNTING TIRES , BEADS MUST CAUSE A FATAL EXPLOSION . 6 . FINISH Keep tractor finish and seat free of gasoline , oil , insect chemicals or battery electrolyte Protect painted surfaces with automotive type wax E _ IING MOWER BELT AGJUSTMENT WASHERS Your tractor has been manufactured with the ability to re - ad - DUST just mower drive belt to provide you with longer belt life , CAP FIGURE 36 If the Mower Clutch Lever ( Fig , 37 ) travels 3 - I / 2 " up the slot in the dash before spring tension resistance is evident , adjust - ment is necessary . NOTE : CHECK FOR PROPER SPRING TENSION WITH ENGINE OFF AND LIFT LEVER IN HIGH - EST POSITION MOWER CLUTCH LEVER " DISENGAGED * ' 1 . Remove mower deck from tractor POSITION IEST " 2 Remove Cotter Pins from both sides of the Rock Shaft DEPTH Assembly ( Fig . 38 ) ADJUSTMENT KNOB 37 Loosen the4 Locknuts on the RH and LH Pivot Brackets , \ ( Fig , 38 ) only unti ! Rock Shaft Assembly can be removed LIFT LEVER * ' LOWEST ' * POSITION 4 Remove Rock Shaft Assembly from R H . and L H Pivot Brackets NOTE : DO NOT DISASSEMBLE BRAKE ROD 5 , Remove Extension Spring from lower hole ( original posi - tion ) in Rock Shaft Assembly and insert in upper hole in Rock Shaft Assembly { Fig . 38 - Inset ) 6 Replace Rock Shaft Assembly between R H and L H Pivot B rac ket s 7 Tighten Locknuts securely making sure Carriage Bolts are seated in square holes of mower housing . 8 , Replace Cotter Pins on both sides of Rock Shaft Assembly NOTE : WHEN INSTALLING A NEW BELT , EXTENSION SPRING MUST BE RETURNED TO LOWER HOLE ( ORIGI - NAL POSITION ) ON ROCK SHAFT ASSEMBLY . FIGURE 37 • ! 9 . ,
Page: 20

TO REMOVE MOWER BELT ENGINE IDLER IDLER PULLEY _ - " • BELT GUIDE NOTE : MOWER BELT INSTALLATION DECAL LOCATED ON MOWER HOUSING , ROCK SHAFT R _ H . _ MANDREL L _ H , REPLACE ONLY WITH THE BELTS SPECIFIED IN THIS MAN [ MANUAL . 1 _ Place Mower Blade Clutch Lever in _ ' DISENGAGED " COTTER PIN position ( Fig ° 37 ) _ 2 . Turn Depth Adjustment Knob to lowest position ° Move Mower Lift Lever ( Fig . 37 ) forward to lower Mower to its lowest position , 3 . Roll Belt off Engine Pulley ( Fig . 38 ) , FIGURE 38 LOWER HOLE ( ORIGINAL 4 , Putt Belt off both Mandrels ° POSITION ) 5 . Spring Belt Guide away from idler Pulley and pull Belt UPPER HOLE _ 1 _ off Idler Pulley , R . H , PIVOT BRACKET 6o Slide Belt fiom under Extension Spring , SPRING TO REPLACE MOWER BELT BRACKET 1 , Slide Belt under Extension Spring ( Fig . 38 ) , _ 2 . Place Belt on rear side of both Mandrels , 3 , Spring Idler Belt Guide down and place Belt around rear side of Idler Pulley _ 4 , Roll Belt over Engine Pulley = R _ H , SUSPENSION RETAINER RETAINER SPRINGS SPRINGS TO REMOVE MOWER 1 . Remove mower ' Belt per instructions under " To Remove Mower Belt " , through step 3 , \ , Turn Depth Adjustment Knob to lowest position . Use Lift Lever to lower mower to its lowest position . . Remove Retainer Spring from Clutch Rod ; pull Clutch Rod out of Clutch BrackeL 4 . Pull Retainer Springs out of Rear Suspension Trunnions . Remove Rear Suspension Trunnions from Lift Brackets ( Fig _ 39 ) ° HINGE PINS ' . Pull Retainer Spring out of Rear Hinge Pin . Remove Rear REAR SUSPENSION Hinge Pin , TRUNNIONS LIFT 6 . Pull Retainer Spring out of Front Hinge Pin . Remove Front BRACKET Hinge Pin ( Fig . ' 39 ) . FIGURE 39 7 . Use Lift Lever to raise Suspension Arms = Slide mower out from under tractor , NOTE : IF AN ATTACHMENT OTHER THAN THE MOWER DECK IS TO BE MOUNTED ON THE TRACTOR , THE L . H . AND Roll , SUSPENSION ARMS ( FIG , 39 ) SHOULD BE REMOVED FROM TRACTOR . STORAGE When mower is to be stored for ' a period of time , clean it thoroughly , remove all dirt , grease , leaves , etc . Give blades and underside of housing a good coat of grease or rust pre , ventativeo Store in a clean dry area , - 20 -
Page: 21

OuBLESNOOTS G POSSIBLE REMEDY POSSIBLE CAUSE WILL NOT START Depress Foot Pedal fully Foot Pedal not depressed Mower Blade Clutch Lever engaged Disengage Lever ( Fig , 10 ) . Be sure Lever is in bottom of slot Fi { i Tank with Gasoline Check Fuel Line and Car - No gasoline in Fuel Tank , clogged Fuel buretor ( clean if necessary ) Replace Fuel Filter Line , or Fuel Filter Bfown Fuse Check for fault and replace Fuse Dead Battery Recharge or reptace Battery HARD TO START Place Throttle Control in " FAST " position ( Fig t0 } Choked improperly , flooded Engine and run starter severa _ times to clear out gas Remove and clean Tank and tines _ Replace Fuel Filter Ctogged Fuel System Remove and clean ( Fig , 28 ) Dirty Air Cleaner Clean , adjust gap or replace ( Fig . 30 ) Spark Plug dirty or improper gap Defective Battery Recharge or replace Defective ignition or loose wiring Check the wiring and Spark Plug Water in gasoline or old fuel Drain Fuel Tank and Carburetor , use fresh fuel and replace Spark Plug Improper Carburetor adjustment Make necessary adjustments ( Fig 31 ) ENGINE MISSES OR LACKS POWER Engine overload Shift to a lower gear { Fig 24 ) or reduce load Clogged Fuel Tank or Fuel Filter Remove and clean Tank ; replace Fuel Filter Partially plugged Air Cleaner Remove and clean ( Fig 28 } Improper Carburetor adjustment Make necessary adiustments ( Fig , 31 t Dirty Engine Air Screen Clean Air Screen ( Fig , 25 ) Low oil level or dirty oit Add or change oil ( page 14 ) Spark Plug dirty , improper gap or wrong type Replace Spark Plug ( Fig 30 ) Faulty ignition Check Spark Plug and for loose wires Poor compression Major Engine overhaul Drain Gas Tank and Carburetor and refill Oil in gasoline ENGINE OVERHEATS Clean Air Screen ( Fig , 25 ) Dirty Air Screen Add or change oil ( page 14 ) Low oil level or dirty oil Clean Engine Cooling Fins ( page 16 ) Dirty Engine Remove and clean Muffler or replace Partially plugged Muffler Remove and clean ( Fig 28 ) Partially plugged Air Cleaner Use fresh fuel and adjust Carburetor ( Fig , 31 } Stale fuel or improper Carburetor adjustment NO LIGHTS Check Fuse , Switch and wire connections Replace No Headlights with Light Switch on and Engine running Headlight Bulbs WON'T CHARGE Blown Fuse Check for fault and replace Replace Defective Battery Defective Diode Assembly Replace Defective Alternator Replace UNSATISFACTORY MOWER PERFORMANCE / UNEVEN DISTRIBUTION OF CLIPPINGS Check air pressure _ n tires ( page 6 ) Tires not inflated properly Mower improperly adjusted Check front to rear and side to side mower adjust - ment ( page 10 ) Grass high or wet Use a slower ground speed ( refer to Mowel Opelating Instructions , page 1 ! ) Incorrect engine RPM's Check engine RPM's ( refer to Carburetor Adjustment . page t7 _ Excessive wear to outer cutting tip of mower blade Replace mower blade Reinstall with top of blade up Improper mower blade installetion Incorrect mower blade Replace with proper mower blade Re - adjust mower drive belt ( page 19 ) Belt slippage b Pour one ounce of engine oil through spark plug hole STORAGE into cylinder I . FUEL SYSTEM c Turn ignition key to _ ' START " position foJ a few a . Drain fuel tank and carburetor by allowing the engine to seconds to distribute oil run out of gasoline , NOTE : GASOLINE LEFT _ N d Replace with new Spark Plug YOUR ENGINE WILL LEAVE GUM DEPOSITS CLOG - 4 , BATTERY GING FUEL SYSTEM . a . Remove battery if tractor is not used regularly during b Dispose of gasoline if not to be used , NOTE : GASO - winter months Store in cool , dry place ( above 50 ° F . ) . LINE STORED FOR SEVERAL MONTHS LOSES ITS b Re - charge each month if necessary . NOTE : BATTERIES VOLATILITY ( ABILITY TO BURN EFFECTIVELY ) , NOT IN USE FOR SEVERAL MONTHS AND NOT 2 . ENGINE OIL KEPT FULLY CHARGED , PRODUCE SULPHATE Drain ( with engine warm ) and replace with clean engine oils DEPOSITS ON PLATES WHICH CANNOT BE RE - ( See chart , page 7L MOVED BY RECHARGING , 3 , CYLINDER 5 , , GENERAL CLEANING a . Remove Spark Plug Clean engine , battery , finish , seat . etc , of all foreign matter - 21 -
Page: 22

LUBRICATIONCHART AXLE PIVOT ( _ ( _ SPINDLE / SPINDLE v - - = _ . . . . - - - - - - - - - - - FRONT WHEEL BEARING _ . . . . . . . , _ : _ , 4 . _ BEARING ( _ N - - - L . ( _ TIEROD " I - ' _ " , . y . _ _ " - - " - " TIE ROD ( _ ( _ STEERING ROD PIVOT . r - = " ' ° " _ CLUTCH PIVOT ( _ ) STEERING ROD PIVOT ( _ ) CLUTCH / BRAKE PIVOT _ CLUTCH / BRAKE ( _ ( _ ATTACAHRMMENTLIFT / PIVOT # AT ATTACHMENT LIFT ARM 1 _ MOWER CLUTCH PIVOT ( _ ( _ SAE 30 MOTOR OIL ( _ GENERAL PURPOSE GREASE SERVICE RECORD FILL IN DATES SERVICE DATES AS YOU COMPLETE REGULAR SERVICE Check EngineOil Level _ ItlP ! Change Engine Oil ( see chart , page 7 ) . . . . . . . . . . . . . . . . . . . _ . . . . . . . . . . . . . . LubricatePivot Points Check Brake Operation Clean Air Screen V i . . . . - Clean Air Cleaner Etement _ ' . . . . . . I . . . . . . . . . : : = . . . . ICfean Engine Cooling Fins ! Replace Spark Plug . . . . . . . . V . . . . . . . . . . . . . . . . . . Check Battery Level _ j I Check Tire Pressure • ' . . . . . . . . . . . . . . . . . . . . . . . . _ # . . . . . . . . . . . . I . . . . . . . . . . . I - 22 -
Page: 23

12 H . P ° 38 " RIDING LAWN TRACTOR - - MODEL NUMBER 917o255741 SCHEMATIC ; RED STARTER % NEUTRAL ATTACH WHITE WHITE RED INTER'K SW INTER'K SW SOLENOID % % SOLID STATE IGNITION ( _ IGNITION SWITCH M BLACK 7 B O SPARK PLUG 30 AMP a G BLACK IGNITION SWITCH STD365402 RECTIFIER CHARGING RED POSITION CIRCUIT ( DIODE ) COIL OFF M - G 3 AMPS , DC 20 VOLTS , AC ( MIN , ) ORANGE AT 3600 RPM , BATTERY IN LINE ON B * L N BROWN START B _ BROWN LIGHT SWITCH WIRING INSULATED CLIPS CHASSIS NOTE : IF WIRING INSULATED CLIPS GROUND AND CABLE TIESWERE REMOVED FOR SERVICING OF UNIT , THEY SHOULD BE REPLACED TO PROPERLY SECURE YOUR WIRING ° . 23 .
Page: 24

REPAHR PARTS 12 H . P . 38 " RIDING LAWN TRACTOR - MODEL NUMBER 917.255741 ELECTRICAL 29 9 % 20 17 ! 1 18
Page: 25

REPAIR PARTS 12 H . P . 38 " RIDING LAWN TRACTOR - - MODEL NUMBER 917.255741 ELECTR ICAL KEY PART DESCRIPTION KEY PART DESCRIPTION NO . NO . NO . NO . ! 7662J Bulb , L , ght 17 719J Cover , Termlnat 2 Cable , Battery 105386X Harness , Light Socket 18 5t14J 3 Cable , Battery 108865X Harness , Ignition 20 42073 4 105613X Key Set 21 STD522507 * Bolt , Hex , 1 / 4 - 20 x 3 / 4 5 * Washer 9 / 32 x 5t8 x t6 Ga . 105381X Switch , Light 22 STD551025 6 104445X Switch , Interlock 23 STD541025 * Nut , HEX 1 / 4 - 20 7 3258,1 Nut , Hex 5 / 8 - 32 24 9272R Battery , 12V . . Sears 8 11t51000 Washer , Lock , Int . Tooth , 5 / 8 25 102476X Terminal Guard 9 STD365402 Switch , Ignition 26 S _ D541625 * Wing Nut 1 / 4 - 20 10 108824X Fuse . 30 Amp . 27 11030400 int , / Ext . Tooth Lockwasher 1 / 4 11 STD551125 * Washer , Lock , 1 / 4 28 72240460 Battery Bolt ( Bolt - Carriage , Rd . Hd . 12 STD541225 * Nut , Hex Jam 1 / 4 - 20 Sqo Neck t / 4 - 20 x 7 • 1 / 2 ) 13 STD522505 * Bolt , Hex , 1 / 4 - 20 x 1 / 2 Gr . 5 29 2008J Solenoid 14 73510400 Nut , Keps 1 / 4 - 20 32 7192J Cable Tie t5 108423X Cable Assembtv - - - 101539X Sheet - Instruction , Tractor 15 ° Slope 16 11050400 Washer Lock , Ext . Tooth , 1 / 4 - - - 109034X Owners Manual * STANDARD HARDWARE - - PURCHASE LOCALLY A B _ ) 12 13
Page: 26

REPAIR PARTS 12 H , P . 38 " RIDING LAWN TRACTOR - - MODEL NUMBER 917.255741 ENCLOSURE 49 54 33 35 29 52 G _ L , 21 G 37 _ 29 20 4O 55
Page: 27

REPAIR PARTS ' 12 H . P . 38 " RIDING LAWN TRACTOR - MODEL NUMBER 917.255741 ENCLOSURE KEY PART DESCRIPTION KEY PART DESCRIPTION NO . NO . NO . NO . t t08446X Seat 33 105792X Hinge , Hood , R . H . 2 17490612 Screw , Hex Washer Thdo R _ tl 3 / 8 - 34 105682X Hood Assembly 16 x 3 / 4 Type TT 35 105678X Grill Assembly 3 17490616 Bracket , Frame , Pivot , R . H . Screw , Hex Washer Thd , Rolling 36 I08500X Bracket , Frame , Pivot , L , H , 3 / 8 - 16 x 1 37 I08501X 4 1055t3X Bracket - Pivot , Seat 38 106927X Side Panel , R . H . 5 t05529X Bolt . Shoulder , 5 / 16 - 18 39 106929X Side Panel , L . H . 6 73680500 Nut , Lock , 5 / 16 - 18 40 108967X Chassis Assembly 7 105512X Drawbar Spring * Compression 41 t02481X 8 105514X Pan - Seat Clamp , Spring 42 108176X 9 105274X Fender 48 105801X Decal - Reflective , Rear 10 19131312 Washer ! 3 / 32 x 13 / 16 x t2 Ga . 49 105802X Decal , Stripe , L . H . 1 ! STD523707 • Bolt , Hex , 3 / 8 - 16 x 3 / 4 50 105803X Decal , Stripe . R . H . , 12 73680600 Nut , Lock 3 / 8 - 16 51 ! 05806X Decal , Grill Craftsman 13 17490608 Screw , Hex Washer Thd . Roll 3 / 8 - 52 105807X Decal , Grill , Stripe 16 x 1 / 2 53 4900J Deca ! , Clutch / Brake " M 14 105753X Bracket . Fender 54 109165X Decal , 12 H . P = 16 105465X Footrest . L . H . 55 108428X Decal , 6 Speed , 38 " 17 Decal . V - Belt Schematic 105464X Footrest , R . H , 56 I05813X 18 STD533707 • Bolt , Carr , 3 / 8 - t6 x 3 / 4 59 10040600 Washer - Lock 3 / 8 19 ! 05466X Pad , Footrest 60 19131212 Washer 13 / 32 x 3 / 4 x t2 Ga . 20 108504X Bracket , Pivot , Grill , R . H . 61 STD523710 * Bolt , He × 3 / 8,16x 1 21 108506X Bracket , Pivot , Grill , L . H . 63 ! 06301X Guide - Belt , Lower , Eng . Pulley , L , H . 22 108067X Pal Nut 1 / 4,20 64 106300X Guide - Belt , Lower , Eng . Pulley , R , H . 24 108361X Lens , L . H . 65 106811X Decal • Stripe , Side Panel , L . H . 25 I08360X Lens , R . H . 66 106812X Decal _ Stripe . Side Panel , R . H . 26 19131210 Washer 13 / 32 x 3 / 4 x 10 Ga . , 67 106974X Decal , OPEl , Caution 27 7603J Washer 13 / 32 x 1 • 1 / 4 x 12 Ga , Tray , Battery 68 19132012 28 6999R Clamp - Hose 69 106909X Screw - Spema ] 29 t05268X Bezel 70 106910X Washer 3O 105685X Strap Assembly , Gril ! 71 106911X Clip 31 108631X Tube - Plastic Decal , II 72 105687X 32 105797X Hinge , Hood , L . H . * STANDARD HARDWARE - - PURCHASE LOCALLY A B C D E F G K L M N O 22 _ : ) 11 _ 61 ( _ 3 _ 61 _ U 11 @ s9o1 ° 068 _ 12 _ ) 6 @ 26 070 @ 12 12 @ 12 Qlz
Page: 28

REPAIR PARTS 12 H . P . 38 " RIDING LAWN TRACTOR - - MODEL NUMBER 917.255741 DRIVE 7O = - - 58 _ r _ ' _ 59 61 1661 90 OPTIONAL EQUIPMENT Spark Arrester Screen Assembly 677V1
Page: 29

; EPAU $ PARTS 12 H . P . 38 " RIDING LAWN TRACTOR - - MODEL NUMBER 917.255741 : ) RIVE KEY PART DESCRIPTION KEY PART DESCRIPTION NO NO . NO NO 49 19131312 Washer 13 / 32 x 13 / 16 x 12 Ga 108872X Engine , t2 HP Model Nor 143 - 366202 5O I05730X Keeper , Belt , Engine 2 51 105731X Pulley , Engine 106191X Keeper , Belt 3 52 9767H Valve , Drain Oil 4470J Spacer 4 53 4859J Idler , Flat STD551143 * Washer , Lock , 7 / t6 5 54 74770728 Bolt , Hex 7 / 16 - 20 x 1 - 3 / 4 106298X Pulley , Idler 6 55 I05705X Bellcrank Assembly ( Inc . Key No 92 ) I05732X V - Belt , Drive 56 STD523715 * Bolt , Hex 3 / 8 - 16 x 1 - 1 / 2 0 10t200K Spacer - Engine 1 108835X Muffler 57 I05709X Spring , Return , Clutch 74030510 Bolt , Filo Hd . Cross , Recess 5 / I6 - 18 x 58 13 207J Washer , Hardened 5 / 8 59 12000039 Ring , Klip 15 t7490632 Screw , Hex Washer Thd Roiling 60 105710X Link , Clutch 318 - 16 x 2 61 76020412 Pin , Cotter t / 8 x 3 / 4 16 19131316 Washer 13 / 32 x 13 / 16 x 16 Gao 62 105724X Bracket , Clutch 17 2949R Gasket , Muffler 63 109127X Rod , Brake 19 108868X Transaxle , 6 Speed , Model No ! 43.920 - 64 106888X Spring , Rod , Brake 002 ( See pages 36 and 37 for parts 65 73350600 Nut - Jam 3 / 8 - 16 breakdown ) • 66 STD551t31 * Washer - Lock 5 / 16 20 STD523127 * Bolt , Hex 5 / 16 - 18 x 2 - 3 / 4 67 105758X Rod , Brake , Parking 21 73680500 Nut , Lock 5 / 16 - 18 68 71673 Cap - Plunger 22 STD580025 * Key , Woodruff 69 t09037X Shaft , Foot Pedal 23 t05703X Pulley , Transaxle 7O 8883R Cover • Pedal 24 12000028 Ring , Retainer 71 19252016 Washer 25 / 32 x t - 1 / 4 x 16 Ga 25 3723J Bracket , Transaxte 72 STD571810 * Pin , Rotlf 3 / 16 x 1 26 STD523710 * Bolt , Hex 3 / 8 - 16 x t 73 106918X Arm , Brake 27 2751R Clip - Fuel Line 74 STD580025 * Key , Woodruff 28 17490512 Screw , Hex Washer Thread Roiling 75 STD580105 * Key , Square 3 / 16 x 2 5 / 16 - ! 8 x 3 / 4 76 104757X Cap , Hub , Rear 30 108171X Support , Battery 77 59192 Cap , Valve 31 109368X Keeper , Belt , L . H . 78 85 t39 Stem , Valve 32 4921H Retainer , Spring 79 106268X Tire , Rear o 18 x 9.50 x 8 33 106190X Clamp 7152J Tube , Tire { not furnished with tractor ) 34 STD523107 * Bolt , Hex 5 / 16 - 18 x 3 / 4 8O 106108X Rim Assembly , Rear 35 73680500 Nut , Lock 5 / t6 - 18 81 108870X Spacer , Split 36 109370X Strap , Locator 82 19252016 Washer 25 / 32 x 1 - 1 / 4 x 16Ga = 37 109369X Keeper , Belt , R . Ho 83 12000001 E - Ring 38 106360X Strap , Torque , Transaxle 88 STD533707 * Bolt , Carriage 3 / 8 - 16 x 3 / 4 39 STD523707 * Bolt , Hex 3 / 8 - 16 x 3 / 4 89 6404J Spacer , Engine , Pulley 40 19252616 Washer 25 / 32 x I - 5 / 8 x 16 Gao 90 73680600 Nut , Lock 3 / 8.16 41 106933X Knob , Shift 91 71040412 Bolt - Fin Hex 1 / 4 - 28 x 3 / 4 42 105699X Rod , Shift 92 105706X Bearing 43 19091210 Washer 9 / 32 x 3 / 4 x 10 Gao 93 106499X Retainer - Belt 44 106362X Washer - Shift , Plate 96 101326L Deflector , Muffler 45 STD561210 * Cotter Pin , 1 / 8 x 1 97 17210806 Screw , Hex Washer No . 8 : - 32 x 3 / 8 46 19151216 Washer 15 / 32 x 3 / 4 x ! 6 Ga . 98 13240300 Elbow ° Street 47 104777X Retainer , Belt 99 STD523727 * Bolt , Hex 3 / 8 - 16 x 2 - 3 / 4 48 17490612 Screw , Hex Washer Thd . Rolling 3 / 8 - 100 105700X Spring - Torsion t6x 3 / 4 101 I08843X Plate , Shift i 102 STD551 ! 25 * Washer - Lock 1 / 4 t03 STD551031 * Washer 11 / 32 X 11 / 16 x 16 Ga . • STANDARD HARDWARE - - PURCHASE LOCALLY N P Q B D E G H J L A 28 34 15 _ 66 35 @ , , @ , , _ 103 - 29 -
Page: 30

_ EPAaR PARTS 12 H , P , 38 " RIDING LAWN TRACTOR - - MODEL NUMBER 917.255741 STEERING AND FRONT AXLE , / - - 66 75 67 55 , 68 63 - 30 -
Page: 31

REPAaR PARTS 12 H . P , 38 " RIDING LAWN TRACTOR _ - MODEL NUMBER 917.255741 STEERING AND FRONT AXLE KEY , PAR T DESCRIPTION KEY PART DESCRIPTION NO NO NO . NO 1 105620X Dash 36 10t930X Washer Ha [ dened 2 74180512 Screw . . Truss Hd , Cross Recess 37 109068X Shaft - Steering - Lower 5 / 16 . . t8 x 3 / 4 38 2882J Pin - Drive 3 / 16 x 1 Spacer _ 627 x . 88 x 695 3 73510500 Nut - Keps 5 / 16 - 18 39 74580 4 105800X Decal - Dash Panel 40 71208 Bushing 5 108793X Control _ Throttle 41 108683X Rod - Steering 7 17720408 Screw . , Hex Thread Cut 1 / 4 . . 20 x 1 / 2 42 105663X Support - Saddle - Rear 8 108456X Decal _ Dash Lower 43 t05664X Support - Saddle - Front 9 105621X Dash - Lower 44 74761060 Bolt - Hex 5 / 8 - 11 x 3 - 3 / 4 Axle - Front ! 1 17190508 Screw . . Hex Washer Hd , Thread Cut 45 105669X Spacer - Axle 5 / 16 - 18 x ! / 2 46 105725X Bearing o Axle 12 108842X _ Saddle 47 t05726X Nut - Lock , Flange 5 / 8 - 11 13 17490608 Screw - Hex Washer Hd . Thread 48 73901000 Screw * Hex Washer Thread Rolling Rolling 3 / 8,16 x 1 / 2 49 17490508 5 / t6 * t8 x 1 / 2 Type TT 15 275tR Clip Klip Ring 16 t05810X Decal • Cap , Steering Wheel 50 12000029 Bearing 17 t00710L Insert - Steering Wheel 51 3366R7t5X Rod - Tie 18 STD541350 * Nut - Hex Jam ! / 2 _ 20 52 105 19 100712K Washer 53 102792X Bushing Washer 13 / 32 x 7 / 8 x 16 Ga . 20 1007 ! 3N Wheel - Steering 54 19131416 Pin - Cotter 1 / 8 x 3 / 4 21 100711L Adapter . , Steering Wheel 55 76020412 • Washer - Lock 3 / 8 22 105647X Sleeve - Steering 56 STD551137 • Nut - Hex 3 / 8 - 24 23 ! 05643X Shaft - Steering , . Upper 57 STD541137 Link - Drag 24 ST0523712 * Bolt _ , Hex 3 / 8 , , 16x 1 - 1 / 4 58 105727X Spindle - L , H . . 25 73680600 Nut . , Lock 3 / 8 - 16 59 t05656X Spindle - R , , H , . 26 17431008 Screw - Hex Self Tap . No . 10 • 16 x 1 / 2 60 I05654X Fitting - Grease 27 t05646X Bracket , _ Sleeve , Steering 6t 278H Bearing - Flangent 28 1554J Bushing - Steering 62 9040H Rim - 6 " . Fro 29 102531X Bracket - Steering 63 106732X Cap - Valve 31 17490612 Screw , . Hex Washer Thread Rolling 64 59192 Stem - Valve 3 / 8 _ 16 x 3 / 4 Type TT 65 65139 Tire - Rib 15 x 6.00 - 6 32 6266H Bearing - Thrust 66 106222X 33 108684X Gear - Sector - - - 59904 Tube . Front ( not furnished with tractor ) Washer 25 / 32 x 1 _ 1 / 4 x 16 Ga , 34 106126X Key - , Woodruff 67 19252016X 68 104757 Cap o Hub - Front 35 12000029 Klip Ring 74 11150500 Washer , Lock , lnt . Tooth 5 / 16 75 19252616 Washer 25 / 32 x I - 5 / 8 x 16 Gao 77 108685X Gear , Pinion * STANDARD HARDWARE , - PURCHASE LOCALLY A C D E F G K 1,1 ® 3 ( _ 74 83 25 31
Page: 32

REPAIIR PARTS 12 HoP . 38 " RIDING LAWN TRACTOR - . MODEL NUMBER 917,255741 , LIFT ADJUSTMENT 25 9 2O C 41 34 4O 22 A A 5 ! - 32 -
Page: 33

REPAIR PARTS 12 H . P . 38 " RIDING LAWN TRACTOR - - MODEL NUMBER 917.255741 LIFT ADJUSTMENT KEY PART DESCRIPTION KEY PART DESCRIPTION NO NO NO NO 1 t06448X Lever . Clutch , Mower 34 105754X Shaft , Lift 2 106932X Knob 35 105768X Lever , Assembly 3 I0645tX Bolt , Shoulder 36 105723X Plunger 4 73680600 Nut , Lock . 3 / 8 • t6 38 t06019X Grip , Handle 5 ! 06452X Bracket , Switch , Interlock 39 4939M Retainer , Spring 6 19171713 Washer 17 / 32 x t • t / 16x t3Ga , 40 ! 05856X Link , Lift 7 1702 t008 Screw , Hex , Tapping , No 10 _ 24 x 41 106204X Trunnion , Lift 1 / 2 42 105855X Link , Lift , Adjustable 8 106447X Support , Lever . Clutch 43 105862X Arm , Suspension , R H . 9 105965X Cap , Fuel 44 t05848X Bolt , Shoulder , 3 / 8 . , t6 t0 t05738X Tank . Fuet 45 I05863X Arm , Suspension , L , H t t 101335K Line . Fuel 46 106308X Trunnion , Lift , Lower ! 2 9151R Grommet 47 STD541250 * Nut , Hex , 1 / 2 - 13 t3 6999R Clamp , Hose 48 9135R Retainer , Spring 14 174906t2 Screw , Hex Washer Thd RolIing 49 19171416 Washer 17 / 32 x 7 / 8 x 16 Ga 3 / 8 - 16 x 3 / 4 50 4921 H Retainer , Spring 15 t0690tX Clamp , Tank , Fuel 51 ! 05864X Bracket , Suspension 20 106920X Panel , Dash , L . H 52 106444X Bracket , Beticrank 21 105505X Cover , Access 53 STD523707 " Bolt , Hex 3 / 8 - 16 x 3 / 4 22 10692 ! X Panel , Dash , R H 54 10644 tX Bettcrank Assembly 23 19292016 Washer 29 / 32 x 1 . . 1 / 4 x 16 Gao 55 76020412 Pin , Cotter , 1 / 8 x 3 / 4 24 12000029 Klip Ring 57 106446X Rod , Clutch , Primary 25 t00734K Knob 59 5320R Clip 26 STD541237 * Nut , Hex . Jam 3 / 8 - 16 6t I05764X Rod Assembly - Lever , Lift 27 105686X Rod , Adjust , Lift 62 105767X Pin - Groove 28 76020308 Pin , Cotter 3 / 32 x t / 2 63 t06810X Spring - Extension 29 2876H Spring 64 72140606 Bolt , Carriage 3 / 8 - 16 x 3 / 4 30 19131016 Washer t3 / 32 x 5 / 8 x 16 Ga 66 108236X Bracket , Switci _ 3t 10t272K Trunnion , Depth Adjustment * STANDARD HARDWARE - . PURCHASE LOCALLY 32 19151216 W3sher 15 / 32 x 3 / 4 x 16Ga 33 12000037 Klip Ring A B C D E _ 44 _ 53 ® 4 ® 4 - 33 -
Page: 34

12H , P , 38 " RIDINGLAWNTRACTOR - - MODELNUMBER917 . 255741 38 " MOWER - " - - t CC 22 A 55 I 56 12 t B I3 68 56 _ 61 ? H H E J 7 E H _ llFF - - REAR BAGGER ATTACHMENT IS BEING I USED , REFER TO REAR BAGGER OWNERS [ MANUAL FOR BLADE PART NOo 41 42 34 -
Page: 35

RSPAUR PARTS 12 H . P . 38 " RIDING LAWN TRACTOR - - MODEL NUMBER 917.255741 38 " MOWER KEY PART DESCRIPTION KEY PART DESCRfPTION NO NQ NO NO t 106085X V - Belt 39 t06634X Blade , 38 " 19132012 Washer 13 / 32 x ! . 1 / 4 x 12 Ga 2 105689X Housing 40 3 8417J Runner , R H 41 ST [ 355 _ 137 * Washer , Lock , 3 " 8 " 4 73680600 Nut , Lock , 3 / 8 . 16 42 STD623715 " Bolt . Hex . 3i8 - 24x 1 . ! 2Gr 5 5 t9111216 Washer , 11 / 32 x 3 / 4 x 16 Ga 43 108250X Spring , Ext 6 72140505 Bolt , Cart , 5 / 16 - 18 x 5 / 8 44 108235X Rod , . Clutch , Mo _ er 7 105896X Bracket , Deflector 45 4921H Spring , Reta : ne _ 8 5846R Nut 46 STD560907 * Pin . , Cotter . 3 32 x 3 4 9 106734X Spring , Deflector 47 108068X Rock Shaft Assembl / 76020616 Pin , Cotter . 3 / 16 x ! 10 106735X Rod oHinge 48 1t 106736X Deflector . . Shield 49 108247X Rod . Brake , Prlmary t2 t05814X Decal 50 STD533707 " Bolt . Cart . 3 / 8 _ . 16 x 3 4 108243X Bracket , Pivot . RH 13 105304X Cap 52 10824tX Bracket , Pivot , L H t4 105662X Link , Parallet 53 105857X Bracket , Susp . Rear . R H 15 105744X Pin - Hinge , Front 54 108673X Bracket , Susp : , Rear , L H 17 105872X Stop , Link 55 t8 105743X Pin - Hinge , Rear 56 106578X Brake Assembly 19 STD523707 * Bolt 3 / 8 _ . 16 x 3 / 4 57 106463X Rod , Brake , Secondary LH 20 73680500 Nut , Lock 5 / 16 . 18 58 108249X Rod , Brake , Secondary , R H 106456X Bracket . Brake , Pivot 21 105659X Bracket , Lift , RH 59 22 105660X Bracket , Lift , LH . 60 I00672K Spacer , Brake 100673L Bracket , Support 23 STD533107 * Bolt , Cam 5 / 16 . 18 x 3 / 4 61 1065 ! 4X Washer , Wear 3 16 24 37133 Instruction - Caution Decal 62 19111016 Washer , 11 / 32 x 5 / 8 x 16 Ga 25 106295X Support , Arm 63 74760684 Bolt , 3 / 8 - 16 x 5 - 1 / 4 26 t05850X Stop , Deck , Front 64 763tj Runner , L H . 27 t 06975X Decal - Safety Standard 65 19131614 Washer 13 / 32 x 1 x 14 Ga , 28 106461X Guide , Belt 66 72140610 Bolt , Carr 38 . 16x 1 , 1 4 29 STD523720 * Bolt 3 / 8 , . 16 x 2 " 67 78850 Decal . . Warning 30 108832X Arm , idler 68 19141614 Washer 7 16 x I x 14 Ga : 3 ! 106902X Spacer 69 STD551037 " Washer 13 32 x 13 t6 x ! 6 Ga 32 102403X Pulley , Idler 70 19141610 Washer 7 t6 x 1 x 10 Ga . 33 106513X Washer , Wear , ! / 16 71 72110606 Bolt , Cart ; age 3 8 . . 16 x 3 4 34 102669X Keeper , Belt 72 19132012 Washer13 32 x t . , 14x12Ga 35 105891X Mandrel Assembly 73 106679X Decal , , Warning 36 100668L Plate , Support , Mandrel 74 76020308 Pin . Cotter 3 32 x 1 2 37 17490612 Screw , Hex Washer Hd , 3 / 8 - 16 x 3 / 4 75 - 76 72110506 Bolt , Carriafle 5 16,118x3 4 38 17490620 Screw , Hex Washer Hd _ 3 / 8 - t6 x1 _ 1 / 4 * STANDARD HARDWARE , , , PURCHASE LOCALLY A B C D E F G H J K L M N 64 If2 , _ 67 @ 71 © 20 _ 5 _ 20 U _ 4 _ 4 _ 20 20 84 @ 4 IF REAR BAGGER ATTACHMENT IS BEING | USED , REFER TO REAR BAGGER OWNERS MANUAL FOR BLADE PART NO , - 35 _
Page: 36

REPAIR PARTS 12 H . P . 38 " RIDING LAWN TRACTOR - - MODEL NUMBER 917.255741 TRANSAXLE - - MODEL NUMBER 143.920 - 002 75 10 35 8 / 31 29 29 _ ( _ - _ 32 6 62 35 < f _ f18 34 _ 60 30 51 30 52 30 69 11 30 53A / 34 26 29 . \ 48 \ 67 37 41 - 36 -
Page: 37

PARTS ; REPAIR 12 H . P . 38 " RIDING LAWN TRACTOR _ - MODEL NUMBER 917.255741 TRANSAXLE - - MODEL NUMBER 143o920 - 002 KEY PART DESCRIPTION KEY PART DESCRIPTION NO . NO , . NO , NO , 1 772094 Cover , Transaxle 38 790006 Pad , Brake 23 780086 Bearing , Needle 39 786026 Pin , Dowel 770082 Case , Transaxle 40 792076 Washer , Flat 4 776260 Shaft , Counter 41 790038 Lever , Brake 5 776219 Shaft Et Pinion Assy , , Output 42 792073 Screw , Flanged hex hd . thread form - 6 778139 Gear , Output ing , 1 / 4 - 20 x 1 - 1 / 4 7 778136 Gear , Spur ( 15 teeth ) 43 792075 Nut , Lock , 5 / 16 - 24 8 792123 Key 44 790025 Holder , Brake pad 9 784216 _ Collar , Shifter 45 776259 Shaft , Brake 10 784337 Rod _ Fork Assy , Shift 46 776135 Shaft , Input 11 778188 Gear , Bevel ( 42 teeth ) 47 774690 Axle ( 11 - t5 / 16 long ) 12 778113A Bevel Pinion , Input 48 774691 Axle ( 16 - 1 / 2 " long ) 13 778221 Gear , Bevel 49 778t46A Gear , Spur ( 37 teeth ) 1415 778068 Gear , Bevel pinion 50 778125 Gear , Spur ( 35 teeth ) 778165 Gear , Ring 51 778124A Gear , Spur { 30 teeth ) 16 786101 Block , Bearing 52 778123A2A Gear , Spur ( 25 teeth ) 17 786040 Pin , Drive 53 77812 Gear , Spur ( 22 teeth ) 18 786110 Spacer 53A 778209 Gear , Spur ( 19 teeth ) 2O 792077 Bail , Steel ( 5116 " dia . ) 54 778211 Gear , Spur ( 12 teeth ) 21 792078 Set Screw , 3 / 8 - 16 x 3 / 8 55 778151 Gear , Spur ( t5 teeth ) 22 792079 Spring 56 778126A Gear , Spur ( 20 teeth ) 23 788061 Ring , Felt 57 778127A Gear , Spur { 25 teeth ) 24 788062 Packing , Felt 58 778128A Gear , Spur ( 28 teeth ) 25 792073 Screw , Flanged hex hd . thread form - 59 778163 Gear , Spur ( 31 teeth ) t ; _ E , ing , 1 / 4 - 20 x 1 - 1 / 4 60 786081 Chain , Roller ( No , 41 chain , 24 links ) 26 792018 Ring , Retainer 61 786082 Sprocket ( 9 teeth ) 27 792035 Ring , Retainer 62 786107 Sprocket ( 18 teeth ) 28 788040 Ring , Retainer 64 07920749 Ptug , Hex hd , , 9 / t6 - 18 thread 29 780072 Washer , Thrust 65 7801 Washer , " Fhrust 3O 780108 Washer , Thrust 66 786067 Spacer 31 780001 Washer 67 792085 Screw , Flanged hex hd , thread form - 32 792001 " O " Ring ing 1 / 4 _ 20 x 2 - 1 / 4 33 788051 Seal , Square cut 68 786086 Bracket , Brake lever 34 780105A Bushing , Flanged 69 780051 Washer , Thrust 35 7801 ! 8A Bushing , Flanged 70 786118 Spacer 36 790003 Disk , Brake 71 788069 Seal , Square cut 37 790007 Plate , Brake pad 75 786116 Disk - 37
Page: 38

R _ PAIR PARTS 12 H . P . 38 " RIDING LAWN TRACTOR - - MODEL NUMBER 917.255741 ENGINE - + MODEL NUMBER 143,366202 ENGINE 13 82 58 62 , , . , , . . - 38 +
Page: 39

REPAIR PARTS 12 H . P . 38 " RIDING LAWN " I - RACTOR ° - MODEL NUMBER 917o255741 ENGINE - - MODEL NUMBER 143.366202 ENGINE DESCRIPTION KEY PART DESCRIPTION KEY PART NO . NO . NO ° NO . 1 Screw , Flanged hex hd , 1 / 4 - 20 x 35323 Cylinder Assy ( Inct Nos 8 _ 13 ) 65 32610A 2 28277 Washer , Flat 29 / 32 3 35324 Rod , Governor 66 t ' 33509 " O " Ring ( Intake ) 4 32651 Lever , Governor 67 t ' 344 ! 0 " 0 " Ring ( Exhaust ) 5 29916 Clamp . Throttle lever 68 33510 Cap , Valve spring 6 650548 Screw . Hex washer hd , 8 - 32 x 5 / 16 69 33507 Spring , Valve 7 35203 Spring , Control 70 33508 Cap , Valve spring keeper 8 35319 Seal , Oil 7t t ' 35295 " O " Ring 9 35326 Baffte , Blower housing 72 35296 Guide , Push rod 10 650561 Screw , Hex washer hd Dudok , ! / 4 - 20 73 650878 Stud , Rocker arm x 5 / 8 74 35297 Arm , Rocker 11 35336 Crankshaft Assy , ( Counterbalance ) 75 35298 Bearing , Rocker arm 12 35327 Gear , Counterbalance 76 28264 Nut , Lock 13 27652 Pin , Dowel 77 33471 Rod , Push 14 29826 Screw , Hex washer hd , 10 - 32 x 3 / 4 78 1 " ' 35299 " 0 " Ring 15 29216 Nut , Lock 79 35300 Cover , Rocker arm housing 16 29918 Washer , E T _ Lock 80 t ' 65O879 Screw , Pan hd , w / seating 17 303 _ Nut 8 - Washer , 10 - 32 " Keps " Lockwasher , 8 - 32 x 1t2 18 Gasket , Valve cover 29642 Ring , Retaining 82 " 27896 19 35329 Piston _ Pin Assy ( Std . ) ( Incl . No . 21 ) 83 28423 Body , Breather 2O Element , Breather 34866 Ring Set , Piston ( Std , ) 84 28424 21 31919 Ring , Piston pin retaining 85 28425 Cover , Valve spring box 22 Tube , Breather 35330 Rod Assy , Connecting ( tncl . No 23 ) 86 35350 23 Screw , Fil hd , Sems , 10 - 24 x 1 / 2 650882 Screw , Connecting rod 87 06501281 24 35313 Lifter , Valve 88 353 Extension , Blower housing 25 Screw , Fil , hal , Seres , 10 - 24 x 1 / 2 35314 Camshaft Assy ( Mech , Compression 89 16501287 Release ) 90 6505 Screw , Fil , flex hd , , 1 / 4 - 20 x 7 / 8 26 Gasket , Carburetor to intake pipe 35315 Weight Assy . , Counterbalance 91 " 33263 27 Pipe , Intake 35316 Extension , Blower housing 92 35304 Link , Governor 28 650128 Screw , Fit hd Seres , 10 _ 24x I / 2 93 3530209A 28A 30688 Screw , Hex hd , Sems , 1 / 4 - 20 x 1 / 2 94 341 Bracket Assy , , Contro _ ( Incl . Nos , 94A Et 94B ) 29 " 35317 Gasket , Mounting flange 30 Spring , Compression 35318 Flange , Mounting ( Inct . Nos , 32 , 33 _ t 94A 3134249 34 ) 94B 6505 Screw , Fil . , hd , 5 - 40 x 7t16 31 Link , Governor spring 31356 Pump Assy , , Oil 94C 35346 32 Screw , Hex washer hd . . setf4ap Sems , 31927 Plug , Oil drain 96 30200 10 - 24 x 9 / 16 33 35319 Seal , Oil 34 35320 Shaft , Governor 97 792028 Screw , Hex hd . Seres , 5 / 16 - 18 x 7 / 8 . 35 Gasket , Intake pipe 31707A Spacer , Governor gear ( tncl No . 36 ) 98 * 3351588 36 30590A Washer , Flat 99 352 Brace , Intake pipe Screw , Hex washer spinlock hd . 37 35321 Gear Assy , , Governor 100 650738 38 thread forming , t / 4 - 20 x 5t8 35322 Spool , Governor 39 Housing , Blower 29193 Ring , Retaining 101 4835338878 Screw , Hex hd , Sems , 1 / 4 - 20 x 1t2 4O 650833 Screw , Hex washer hd . Powerlok , 102 93067 1 / 4 - 20 x 1 - 3 / 16 103 2 Screw , Phil , Hex hd , Sems , 5 / t6 - 24 x 21 t32 4412 32589 Key , AFlywheelmp , Cover , Cylinder head 611093 Flywheel ( 3 w / ring gear ) t04 35290 Screw , FiL hd , Sems , 5 / 16 - 18 x 1 / 2 43 650880 Washer , Lock 105 650273 44 Screw , Hex hd _ Seres , 1 / 4 - 20 x 1t2 650881 Nut , Flywheel 111 30668 Ssreen , Starter 45 35135 Solid State Assy . ( Incl No 45A ) 115 35411 45A Pop , Rivet ( Can be purchased locally ) 610118 Cover , Spark plug 115A 46 650872 Stud , Solid State Assy 116 34113 Plug , Blower housing 47 650814 Screw , Hex hd Seres , 10 - 24 x I 1t8 29774 Line , Fuel 49 Clamp , Fuel line " 35306 Gasket , Cylinder head 119 26460 5O Filter , Fuel ( tnci No o 119 ) 35307 Head Assy , Cylinder 119A 34279A3 730218 Valve Guide Kit ( tncf 2 of No 52 ) 120 2779 Clip , Conduit 5152 Screw , Hex washer hdo Sems , t0 - 32 x 34315 Ring , Retaining 121 28942 3 / 8 53 35308 Valve , Exhaust ( Std . ) 54 35309 Valve , Intake ( Std ) 125 33992A Tube , Oil fill 55 650691 Washer , Fiat 126 33589A Dipstick , Oi _ ( Incl , No , 127 ) 56 650690 Washer , Be [ levilie 127 33590 " O " R _ ng 57 650746 Screw , Hex hd , 5 / 16 - 18 x 3 / 8 128 34909 Body , Air cleaner Fiiter , Fe _ t air cleaner 58 650692 Screw , Hex hd , , 5 / 16 - 18 x ! - 3 / 4 129 35108 59 34046 Resistor Spark Plug ( Champion RL - 130 34910 Filter , Air cleaner Screw , Fil hd Seres , 10o32 x 5 - 1 / 4 86C or equivalent } 131 650875 6O Clip t ' 33481 " O " Ring 131A 35437 6OA t ' 35358 " 0 " PRingush 6t 33480 Tube , rod 62 35310 Housing , Rocker arm 63 * Indicates Part _ , ! , _ cluded in t " 33484 " 0 " , Ring 64 650168 Washer Flat Gasket Set Key No 174 - 39 -
Page: 40

REPAIR PAR TS 12 H . P . 38 " RIDING LAWN TRACTOR - - MODEL NUMBER 917.255741 ENGINE - oMODEL NUMBER 143,366202 ENGINE 40 -
Page: 41

REPAIR PARTS 12 H . P . 38 " RIDING LAWN TRACTOR - - MODEL NUMBER 917.255741 ENGINE - - MODEL NUMBER 143,366202 ENGINE KEY PART DESCRIPTION KEY PART DESCRIPTION NOo NO . , NO , NO , 132 ' 33629 Gasket , Air cleaner elbow 169 30688 Screw , Hex hd . Sems , t / 4 - 20 x 112 133 * 34912 Gasket , Air cleaner to housing t70 34346 Decal , instruction ! 34 35286 Adapter , Air cteaner 170B 34387 Decal , Instruction 135 650784 Screw , Hex hd . taptite , w ! flatwasher , t71 632413 Carburetor ( Inct No , 91t t0 - 24 x tl / 16 173 33605 Motor , Electric starter 136 34911 Cover , Air cleaner 174 35331 Gasket Set ( Incl items marked " ) 137 611096 Coil Assy , , Alternator ( 3 Amp DC ) t75 35332 " O " Ring Kit ( lnd items marked tt { Inct , Nos . t38 , 139 8 - 140 ) 137A 650873 " indicates Pans Included in Screw , Hex hd Sems , t / 4 - 20 x 3 / 4 138 610935 Diode Gasket Set Key No 174 ! 39 610921 Connector Body 140 610922 Female Terminal t Indicates Parts Included in 143 33997 Clip , Oil fill tube " O " Ring Kit , Key No . 175 , - 41 -
Page: 42

$ 111PAIII PAIIT $ 12 H . P . 38 " RIDING LAWN TRACTOR - MODEL NUMBER 917.255741 ENGINE - - MODEL NUMBER 143.366202 CARBURETOR NO . 632413 DESCRIPTION 1 _ . . . 4 _ 7 / _ NO NO . . KEY 4PART13 - _ " 632 Carburetor t , - " _ _ 1 632243 Shaft Ef Lever Assy . , Throttle Spring , Throttle return 2 - . _ i ' _ _ _ 17 _ I _ 15 2 632244 Shutter , Throttle Screw , Rd hd , 4 - 40 x 3 / 16 27 - - , , . , _ @ to _ 14 - " _ 4 650506 Spring , Idle regulating screw 4 29 _ = _ _ : _ f " ° ' , ' @ . / 35 5A66330726624 630738 Spring , Main adjustment screw 26e " " _ " . z " , ' ' _ ( _ . . _ Screw , idle regulating 5 3 _ _ j _ ) . _ _ _ . _ _ , , 6 650417 Shaft _ Lever Assy , Choke 6 Shutter , Choke r _ 9 632248 Plug , Welch ' , . _ 16 10 " 630748 ; _ . . 11 " 63 ! 027 Plug , Welch 12 _ 631021 Inlet Needle , Seat 8 Clip Assy . ( fnc ! . No . 13 ) 13 631022 Clip , Inlet needle _ Y " < , , 5 30 * ' " _ L . ) ; i , , 11 _ , it 14 632019 Float , Carburetor 24 , I 15 * 631024 Shaft , Float 16 * 631867 Bowl , Float t , 17 632247 Spring I 18 631183 Washer , Felt 21 27110 Gasket , Bowl - to - body 22 * 632239 Main Adjustment Screw Assy . , ( Incl Nos , 5A , 21 , 23 8 30 ) / & . 3t 23 630740 I / " 0 " Ring , Adjustment screw Screw , Idle adjustment / 24 * 6322818 25 * 63102 Gasket , Bowl - to - body Fuel Fitting 27 631184 Washer _ 4 . - ' _ " " - - . . 26631775 Seal , Dust 30 630739 Washer , Flat 29 6319717 31 63234 Repair Kit find items marked * ) STARTER MOTOR NO , 33605 11 KEY PART DESCRIPTION 18 12 NO . NO . 33605 Starting Motor , Complete 1 33451 Cover , Dust 2 33842 Ring , Retainer 3 33430 Retainer , Spring 4 33431 Spring , Anti - drift 13 5 33432 Gear 6 33433 Nut , Engaging 7 33450 Nut , Lock 8 33434 Cap Assy . , Drive end 11 33712 Card Assy . . , Brush ( IncL No . 12 ) 12 33705 Brush 8 " Spring Kit { Inclo 4 pcs . . of No . 13 ) 13 33440 Spring , Brush 10 14 590500 Washer , Thrust 15 33449 Bolt , 10 - 32 x 4 - 1 / 4 16 33706 Cap Assyo , Commutator end j 17 650168 Washer , Flat 18 650723 Nut , Hex 8 6 1 2
Page: 43

SUGGESTED GUIDE FOR SUGHTING SLOPES FOR SAFE OPERATUON ONLY RiDE UP AND DOWN HiLL NOT ACROSS HILL SIGHTING . GUIDE SIGHT AND HOLD THiS LEVEL WiTH SKY LINE OR TREE t5 ° MAX . Operate your Tractor up and down the face of slopes ( not greater than 15 ° ) ; never across the face . Make turns gradu - ally to prevent tipping or loss of control . Exermse extreme caution when changing direction on slopes .
Page: 44

12 H . P . OWNERS 38 " RID JNG MANUAL LAWN TRACTOR ELECTRIC START MODEL NO . The Model Number will be found on the Model Plate attached to the Fender , , Always mention the Model Number when 917.255741 requesting service or parts for ' your Lawn Tractor . Al ! parts listed herein may be ordered from any Sears Service Center / Departments and most Sears Retail Stores . WHEN ORDERING REPAIR PARTS , ALWAYS GIVE THE FOLLOWING INFORMATION : ® THE PART NUMBER • THE PART DESCRIPTION ® THE MODEL NUMBER O THE NAME OF MERCHANDISE HOW TO ORDER REPAIR PARTS If the parts you need are not stocked locally , your order will be electronically transmitted to a Sears Repair Parts Distribu - tion Center for " expedited handling " . Sears , Roebuck and Co . , Chicago , IL 60684 U , S . A .
Search in Tractors-Riding-Lawnmowers on ebay
"
* Clicking the part number will send you to Sears Parts Direct.
0109034X Manual
0101539X Instructions
0677V1 Spark arrester screen assembly
024939 Bagger
024669 Mulching kit
0122215X Mower deck
0110096X Sheet - instruction
17662J Bulb, light
10108824X Fuse, 30 amp.
11STD551125 Washer, lock, 1/4 (standard hardware--purchase ...
12STD541225 Nut, hex jam 1/4 - 20 (standard hardware--purch...
13STD522505 Bolt, hex, 1/4 - 20 x 1/2 gr. 5 (standard hardw...
1473510400 Nut, keps 1/4 - 20
15108423X Cable
1611050400 Washer lock, ext. tooth, 1/4
17719J Cover, terminal
185114J Cable
2105386X Harness, light socket
204207J Cable
21STD522507 Bolt, hex, 1/4 - 20 x 3/4 (standard hardware--p...
22STD551025 Washer 9/32 x 5/8 x 16 ga. (standard hardware--...
23STD541025 Nut, hex 1/4 - 20
249272R Battery, 12v., sears
25102476X Terminal guard
26STD541625 Wing nut 1/4 - 20 (standard hardware--purchase ...
2711030400 Lock washer
2872240460 Battery bolt (bolt - carriage, rd. hd. sq. neck...
292008J Solenoid
3108865X Harness, ignition
307192J Cable tie
4105613X Key set
6104445X Switch
73258J Nut, hex 5/8 - 32
811151000 Washer, lock, int. tooth, 5/8
9STD365402 Switch
0109034X Manual
0101539X Instructions
0677V1 Spark arrester screen assembly
024939 Bagger
024669 Mulching kit
0122215X Mower deck
0110096X Sheet - instruction
1108446X Seat
1019131312 Washer
11STD523707 Bolt, hex, 3/8 - 16 x 3/4 (standard hardware--p...
1273680600 Nut, lock 3/8 - 16
1317490608 Screw
14105753X Bracket, fender
16105465X Footrest, l.h.
17105464X Footrest, r.h.
18STD533707 Bolt, carr. 3/8 - 16 x 3/4 (standard hardware--...
19105466X Pad, footrest
217490612 Screw, hex washer thd. roll 3/8 - 16 x 3/4 type tt
20108504X Bracket, pivot, grill, r.h.
21108505X Bracket, pivot, grill, l.h.
22108067X Nut
24108361X Lens lh
25108360X Lens, r.h.
2619131212 Washer 13/32 x 3/4 x 10 ga.
277603J Tray
28109596X Hose clamp
29105268X Bezel
317490616 Screw, hex washer thd. rolling 3/8 - 16 x 1
30105685X Strap assembly, grill
31108631X Decal
32105797X Hinge, hood, l.h.
33105792X Hinge, hood, r.h.
34105682X Hood assembly
35105678X Grill assembly
36108500X Bracket, frame, pivot, r.h.
37108501X Bracket, frame, pivot, l.h.
38106927X Side panel, r.h.
39106929X Side panel, l.h.
4105513X Bracket - pivot, seat
40108967X Chassis assembly
41102481X Drawbar
42108176X Pan - seat
48105801X Decal - reflective, rear
49105802X Decal, stripe, l.h.
5105529X Bolt, shoulder, 5/16 - 18
50105803X Decal, stripe, r.h.
51105806X Decal, grill craftsman
52105807X Decal, grill, stripe
534900J Decal, clutch/brake
54109165X Decal, 12 h.p.
55108428X Decal, 6 speed, 38"
56105813X Decal v-belt schematic
5910040600 Washer - lock 3/8
673680500 Nut, lock, 5/16 - 18
6019131212 Washer
61STD523710 Bolt, hex 3/8 - 16 x 1 (standard hardware--purc...
63106301X Guide - belt, lower, eng. pulley, l.h.
64106300X Guide - belt, lower, eng. pulley, r.h.
65106811X Decal - stripe, side panel, l.h.
66106812X Decal - stripe, side panel, r.h.
67106974X Decal, opei, caution
6819132012 Washer
69106909X Screw
7105512X Spring
70106910X Washer
72105687X Tube - plastic
8105514X Clamp, spring
9105274X Fender
0109034X Manual
0101539X Instructions
0677V1 Spark arrester screen assembly
024939 Bagger
024669 Mulching kit
0122215X Mower deck
0110096X Sheet - instruction
1108872X Engine, 12 h.p. model no. 143.366202
10101200K Spacer - engine
100105700X Spring - torsion
101108843X Plate
102STD551125 Washer - lock 1/4 (standard hardware--purchase ...
103STD551031 Washer 11/32 x 11/16 x 16 ga. (standard hardwar...
11108835X Muffler
1374030510 Bolt, fil. hd. cross, recess 5/16 - 18 x 5/8
1517490632 Screw
1619131316 Washer 13/32 x 13/16 x 16 ga.
172949R Gasket, muffler
19108868X Transaxle, 6 speed, model no. 143.920-002
2105731X Pulley, engine
2173680500 Nut, lock 5/16 - 18
22STD580025 Key, woodruff (standard hardware--purchase loca...
23105703X Pulley, transaxle
2412000028 Ring retainer
253723J Bracket, transaxle
26STD523710 Bolt, hex 3/8 - 16 x 1 (standard hardware--purc...
272751R Clip
2817490512 Screw, hex washer thread rolling 5/16 - 18 x 3/4
39767H Valve
30108171X Support, battery
31109368X Keeper, belt, l.h.
324921H Spring retainer
33106190X Clamp
34STD523107 Bolt, hex 5/16 - 18 x 3/4 (standard hardware--p...
3573680500 Nut, lock 5/16 - 18
36109370X Strap, locator
37109369X Keeper, belt, r.h.
38106360X Strap, torque, transaxle
39STD523707 Bolt, hex 3/8 - 16 x 3/4 (standard hardware--pu...
4STD551143 Washer, lock, 7/16 (standard hardware--purchase...
4019252616 Washer 25/32 x 1 - 5/8 x 16 ga.
41106933X Knob
42105699X Rod, shift
4319091210 Washer
44106362X Washer
45STD5610210 Cotter pin, 1/8 x 1 (standard hardware--purchas...
4619151216 Washer
47104777X Retainer, belt
4817490612 Screw, hex washer thd. rolling 3/8 - 16 x 3/4
4919131312 Washer
574770728 Bolt
50105730X Keeper
51106191X Keeper, belt
524470J Spacer
534859J Idler, flat
54106298X Pulley, idler
55105705X Bellcrank assembly (inc. key no. 92)
56STD523715 Bolt, hex 3/8 - 16 x 1 - 1/2 (standard hardware...
57105709X Spring
58207J Washer
5912000039 Ring
6105732X V-belt, drive
60105710X Link
6176020412 Pin, cotter 1/8 x 3/4
62105724X Bracket, clutch
63109127X Rod brake
64106888X Spring rod
6573350600 Nut - jam 3/8 - 16
66STD551131 Washer - lock 5/16 (standard hardware--purchase...
67105758X Rod, brake, parking
6871673 Plunger cap
69109037X Shaft, foot pedal
7119252016 Washer 25/32 x 1 - 1/4 x 16 ga.
72STD571810 Pin, roll, 3/16 x 1 (standard hardware--purchas...
73106918X Arm
74STD580025 Key, woodruff (standard hardware--purchase loca...
75STD580105 Key, square 3/16 x 2 (standard hardware--purcha...
76104757X Cap, hub, rear
7759192 Valve cap
7865139 Valve stem
79106268X Tire, rear - 18 x 9.50 x 8
79A7152J Tube
80106108X Rim assembly, rear
81108870X Spacer, split
8219252016 Washer 25/32 x 1 - 1/4 x 16 ga.
8312000001 E-ring
88STD533707 Bolt, carriage 3/8 - 16 x 3/4 (standard hardwar...
896404J Spacer
9073680600 Nut, lock 3/8 - 16
9171040412 Bolt - fin. hex 1/4 - 28 x 3/4
92105706X Bearing
93106499X Retainer - belt
96101326L Deflector
9717210806 Screw, hex washer no. 8 - 32 x 3/8
9813240300 Elbow
99STD523727 Bolt, hex 3/8 - 16 x 2 - 3/4 (standard hardware...
0109034X Manual
0101539X Instructions
0677V1 Spark arrester screen assembly
024939 Bagger
024669 Mulching kit
0122215X Mower deck
0110096X Sheet - instruction
1105620X Dash
1117190508 Screw - hex washer hd. thread cut. 5/16 - 18 x 1/2
12108842X Saddle
1317490608 Screw
152751R Clip
16105810X Decal - cap, steering wheel
17100710L Insert - steering wheel
18STD541350 Nut - hex jam 1/2 - 20 (standard hardware--purc...
19100712K Washer
274180512 Screw
20100713N Wheel - steering
21100711L Adapter - steering wheel
22105647X Sleeve - steering
23105643X Shaft - steering - upper
24STD523712 Bolt - hex 3/8 - 16 x 1 - 1/4 (standard hardwar...
2573680600 Nut - lock 3/8 - 16
2617431008 Screw - hex self tap no. 10 - 16 x 1/2
27105646X Bracket - sleeve, steering
281554J Bushing - steering
29102531X Bracket - steering
373510500 Nut - keps 5/16 - 18
3117490612 Screw - hex washer thread rolling 3/8 - 16 x 3/...
326266H Thrust washer
33108684X Gear
34106126X Key
3512000029 Ring
36101930X Washer hardened
37109068X Shaft - steering - lower
382882J Pin - drive 3/16 x 1
3974580 Spacer .627 x .88 x .695
4105800X Decal - dash panel
4071208 Bushing
41108683X Rod - steering
42105663X Support - saddle - rear
43105664X Support
4474761060 Bolt
45105669X Axle - front
46105725X Spacer - axle
47105726X Bearing - axle
4873901000 Nut
4917490508 Screw
5108793X Control - throttle
5012000029 Ring
513366R Bearing
52105715X Rod - tie
53102792X Bushing
5419131416 Washer
5576020412 Pin - cotter 1/8 x 3/4
56STD551137 Washer - lock 3/8 (standard hardware--purchase ...
57STD541137 Nut - hex 3/8 - 24 (standard hardware--purchase...
58105727X Drag link
59105656X Spindle - l.h.
60105654X Spindle - r.h.
61278H Fitting
629040H Flange bearing
63106732X Rim - 6" - front
6459192 Valve cap
6565139 Valve stem
66106222X Tire - rib 15 x 6.00 - 6
66A59904 Tube
6719252016 Washer 25/32 x 1 - 1/4 x 16 ga.
68104757X Cap - hub - front
717720408 Screw
7411150500 Washer, lock, int. tooth 5/16
7519252616 Washer 25/32 x 1 - 5/8 x 16 ga.
77108685X Gear, pinion
8108456X Decal - dash lower
9105621X Dash - lower
0109034X Manual
0101539X Instructions
0677V1 Spark arrester screen assembly
024939 Bagger
024669 Mulching kit
0122215X Mower deck
0110096X Sheet - instruction
1106448X Lever, clutch, mower
10105738X Tank, fuel
11101335K Line, fuel
129151R Bushing
136999R Clamp, hose
1417490612 Screw, hex washer thd. rolling 3/8 - 16 x 3/4
15106901X Clamp, tank, fuel
2106932X Knob
20106920X Panel, dash, l.h.
21105505X Cover, access
22106921X Panel, dash, r.h.
2319292016 Washer
2412000029 Ring
25100734K Knob
26STD541237 Nut, hex jam 3/8 - 16 (standard hardware--purch...
27105686X Rod, adjust, lift
2876020308 Pin, cotter 3/32 x 1/2
292876H Spring
3106451X Bolt, shoulder
3019131016 Washer
31101272K Trunnion depth adjustment
3219151216 Washer
3312000037 Ring
34105754X Lift shaft
35105768X Lever, assembly
36105723X Plunger
38106019X Grip, handle
394939M Retainer, spring
473680600 Nut, lock, 3/8 - 16
40105856X Link, lift
41106204X Trunnion, lift
42105855X Lift link
43105862X Arm, suspension, r.h.
44105848X Bolt,
45105863X Arm, suspension, l.h.
46106308X Trunnion, lift, lower
47STD541250 Nut, hex, 1/2 - 13 (standard hardware--purchase...
489135R Spring
4919171416 Washer
5106452X Bracket, switch, interlock
504921H Spring retainer
51105864X Bracket, suspension
52106444X Bracket, bellcrank
53STD523707 Bolt, hex 3/8 - 16 x 3/4 (standard hardware--pu...
54106441X Bellcrank assembly
5576020412 Pin, cotter, 1/8 x 3/4
57106446X Rod, clutch, primary
595320R Clip
619171713 Washer 17/32 x 1 - 1/16 x 13 ga.
61105764X Rod assembly - lever, lift
62105767X Pin
63106810X Spring
6472140606 Bolt, carriage 3/8 - 16 x 3/4
66108236X Bracket
717021008 Screw hex, tapping, no. 10 - 24 x 1/2
8106447X Support, lever, clutch
9105965X Cap, fuel
0109034X Manual
0101539X Instructions
0677V1 Spark arrester screen assembly
024939 Bagger
024669 Mulching kit
0122215X Mower deck
0110096X Sheet - instruction
1109598X Bracket, lift r.h.
2110029X Link, lift
0109034X Manual
0101539X Instructions
0677V1 Spark arrester screen assembly
024939 Bagger
024669 Mulching kit
0122215X Mower deck
0110096X Sheet - instruction
1106085X V - belt
10106735X Rod
11106736X Deflector
12105814X Decal
13105304X Cap
14105662X Link, parallel
15105744X Front Rod
17105872X Stop, link
18105743X Pin - hinge, rear
19STD523707 Bolt 3/8 - 16 x 3/4 (standard hardware--purchas...
2105689X Housing
2073680500 Nut, lock 5/16 - 18
21105659X Bracket, lift, r.h.
22105660X Bracket, lift, l.h.
23STD533107 Bolt, carr. 5/16 - 18 x 3/4 (standard hardware-...
243713J Instruction - caution decal
25106295X Support, arm
26105850X Stop, deck, front
27106975X Decal - safety standard
28106461X Guide, belt
29STD523720 Bolt 3/8 - 16 x 2" (standard hardware--purchase...
38417J Runner, r.h.
30108832X Arm, idler
31106902X Spacer
32102403X Idler
33106513X Washer
34102669X Keeper, belt
35105891X Mandrel assembly
36100668L Plate, support, mandrel
3717490612 Screw, hex washer hd. 3/8 - 16 x 3/4
3817490620 Screw, hex washer hd. 3/8 - 16 x 1 - 1/4
39106634X Blade, 36"
473680600 Nut, lock, 3/8 - 16
4019132012 Washer
41STD551137 Washer, lock, 3/8 (standard hardware--purchase ...
42STD623715 Bolt, hex, 3/8 - 24 x 1 - 1/2 gr. 5 (standard h...
43108250X Spring
44108235X Rod - clutch, mower
454921H Spring retainer
46STD560907 Pin - cotter 3/32 x 3/4 (standard hardware--pur...
47108068X Rock shaft assembly
4876020616 Pin, cotter, 3/16 x 1
49108247X Primary rod , brake
519111216 Washer
50STD533707 Bolt, carr. 3/8 - 16 x 3/4 (standard hardware--...
52108243X Bracket, pivot, r.h.
53108241X Bracket, pivot, l.h.
54105857X Bracket, susp., rear, r.h.
55108673X Bracket
56106578X Brake
57106463X Rod
58108249X Rod
59106456X Bracket, brake, pivot
672140505 Bolt, carr., 5/16 - 18 x 5/8
60100672K Spacer
61100673L Bracket, support
62106902X Washer, wear 3/16
6319111016 Washer
6474760684 Bolt, 3/8 - 16 x 5 - 1/4
657631J Runner, mower left hand
6619131614 Washer 13/32 x 1 x 14 ga.
6772140610 Bolt, carr. 3/8 - 16 x 1 - 1/4
6878850 Decal - warning
6919141614 Washer 7/16 x 1 x 14 ga.
7105896X Bracket, deflector
70STD551037 Washer 13/32 x 13/16 x 16 ga. (standard hardwar...
7119141610 Washer 7/16 x 1 x 10 ga.
7272110606 Bolt, carriage 3/8 - 16 x 3/4
7319132012 Washer
74106679X Decal - warning
7576020308 Pin, cotter 3/32 x 1/2
7672110506 Bolt, carriage 5/16 - 18 x 3/4
85846R Nut
9106734X Spring, deflector