Home | Register Login | Wanted Manuals | MarketPlace | Members Area | Manuals Manufacturer Directory | UPC Lookup | Information Pages | Policy


Back To Craftsman Walk-Behind-Mowers       Model: 917.377543 or 917377543 Craftsman 6.5 HP 22 Inch Rear Discharge Lawn Mower
Regular Text Search or Search by Model Number

Register / log-in to add to your Hammerwall Collection.
Manual Location


This is a partial text extraction from the pdf, to download the pdf, click the Manual tab. If you want to search this text, hold control and F, and type the word you are looking for.

Page: 1

Owner's Manual CRAFTS [ MA + N 6.5 HORSEPOWER 22 " REAR DISCHARGE POWER PROPELLED ROTARY LAWN MOWER Model No . 917.377543 • Safety • Assembly • Operation • Maintenance - • EspaSol • Repair Parts CAUTION : Read and follow all Safety Rules and Instructions before operating this equipment Sears , Roebuck and Co . , Hoffman Estates , IL 60179
Page: 2

Warranty 2 Product Specifications 11 Safety Rules 2 Service and Adjustments 14 Assembly 4 Storage 16 Operation 6 Troubleshooting 17 Maintenance Schedule 10 Repair Parts 37 Maintenance 10 Parts Ordering Back Cover LIMITED TWO YEAR WARRANTY ON CRAFTSMAN POWER MOWER For two years from date of purchase , when this Craftsman Lawn Mower is maintained , lubricated , and tuned up according to the operating and maintenance instructions in the owner's manual , Sears will repair free of charge any defect in material or workmanship . If this Craftsman Lawn Mower is used for commercial or rental purposes , this warranty applies for only 90 days from the date of purchase . This Warranty does not cover : • Expendable items which become worn during normal use , such as rotary mower blades , blade adapters , belts , air cleaners and spark plug . • Repairs necessary because of operator abuse or negligence , including bent crank - shafts and the failure to maintain the equipment according to the instructions con - tained in the owner's manual . Warranty service is available by retuming the Craftsman power mower to the nearest Sears Service Center / Department in the United States . This warranty applies only while this product is in use in the United States . This Warranty gives you specific legal rights , and you may also have other rights which vary from state to state . SEARS , ROEBUCK AND CO . , D / 817 WA , HOFFMAN ESTATES , ILLINOIS 60179 Safety standards require operator • Do not operate mower if it has been presence controls to minimize the dropped or damaged in any manner . risk of injury . Your unit is equipped Always have damage repaired before with such controls . Do not attempt to using your mower . defeat the function of the operator • Do not use accessory attachments that presence controls under any are not recommended by the manufac - circumstances . turer . Use of such attachments may be TRAINING : hazardous . • Read this operator's manual carefully . • The blade turns when the engine is Become familiar with the controls and running . know how to operate your mower PREPARATION : properly . Leam how to quickly stop • Always thoroughly check the area to be mower . mowed and clear it of all stones , sticks , • Do not allow children to useyour mower . wires , bones , and other foreign objects . Never allow adults to use mower without These objects will be thrown by the blade proper instructions . and can cause severe injury . • Keep the area of operation clear of all • Always wear safety glasses or eye persons , especially small children and shields when starting and while using pets . your mower . • Use mower only as the manufacturer intended and as described in this manual . 2
Page: 3

• Do not run the engine indoors . Exhaust • Dress properly . Do not operate mower fumes are dangerous . when barefoot or wearing open sandals . • Never cut grass by pulling the mower Wear only solid shoes with good traction towards you . Mow across the face of when mowing . • Check fuel tank before starting engine . slopes , never up and down or you might lose your footing . Do not mow exces - Do not fill gas tank indoors , when the sively steep slopes . Use caution when engine is running or when the engine is operating the mower on uneven terrain hot . Allow the engine to cool for several or when changing directions - - maintain minutes before filling the gas tank . Clean off any spilled gasoline before starting the good footing . • Never operate your mower without engine . proper guards , plates , grass catcher or • Always make wheel height adjustments other safety devices in place . before starting your mower . Never attempt to do this while the engine is MAINTENANCE AND STORAGE : running . • Check the blade and the engine mount - • Mow only in daylight or good artificial ing bolts often to be sure they are light . tightened properly . OPERATION : • Check all bolts , nuts and screws at frequent intervals for proper tightness to • Keep your eyes and mind on your mower be sure mower is in safe working and the area being cut . Do not let other condition . interests distract you . • Keep all safety devices in place and • Do not mow wet or slippery grass . Never run while operating your mower . Always working . • To reduce fire hazard , keep the engine be sure of your footing - - keep a firm hold on the handles and walk . free of grass , leaves or excessive grease and oil . - • Do not put hands or feet near or under • Check grass catcher often for deteriora - rotating parts . Keep clear of the discharge tion and wear and replace worn bags . opening at all times . • Always stop the engine whenever you Use only replacement bags that are recommended by and comply with leave or are not using your mower , or before crossing driveways , walks , roads , specifications of the manufacturer of your mower . and any gravel - - - covered areas . • Always keep a sharp blade on your • Never direct discharge of matedal toward mower . bystanders nor allow anyone near the mower while you are operating it . • Allow engine to cool before storing in any enclosure . • Before cleaning , inspecting , or repairing • Never store mower with fuel in the tank your mower , stop the engine and make absolutely sure the blade and all moving inside a building where fumes may reach parts have stopped . Then disconnect the an open flame or an ignition source such as a hot water heater , space heater , spark plug wire and keep it away from the spark plug to prevent accidental starting . clothes dryer , etc . • Do not continue to run your mower if you ACAUTION : Always disconnect spark hit a foreign object . Follow the procedure plug wire and place wire where it cannot contact spark plug in order to prevent outlined above , then repa _ any damage before restarting and operating you accidental starting when setting up , mower . transporting , adjusting or making repairs . • Do not change the governor settings or WARNING overspeed the engine . Engine damage or The engine exhaust from this product personal injury may result . contains chemicals known to the State of • Do not operate your mower if it vibrates California to cause cancer , birth defects , abnormally . Excessive vibration is an or other reproductive harm . indication of damage ; stop the engine , safely check for the cause of vibration and repair as required . 3
Page: 4

Theseaccessoriewsereavailablewhenthislawnmowewr asproduced . They are also available at most Sears retailoutlets and servicecanters . Most Sears stores can also order repairparts foryou , when you provide the model number of your lawn mower . Some of these accessories may notapply to your lawn mower . LAWN MOWER PERFORMANCE CUPPING DEFLECTOR FOR REAR DISCHARGE LAWN MOWERS MULCHERKITS STABILIZER FOR FOR REAR DISCHARGE SIDE DISCHARGE / _ GRASS CATCHERS _ ! GRASS SCATCHERS LAWN MOWERS LAWN MOWER GAS CANS LAWN MOWER MAINTENANCE MUFFLERS AIR FILTERS SPARK PLUGS BELTS BLADES BLADE ADAPTERS WHEELS ENGINE OIL Read these instructionsand this manual in its • RolllawnmoweroutOfcartonandcheck entiretybefore you attempt to assemble or cartonthoroughlyforadditionallooseparts , operate your new lawn mower . Your new lawn HOW TO SET UP YOUR LAWN mower has been assembled at the factorywith MOWER the exception of those parts leftunassemblad TO UNFOLD HANDLE for shippingpuq _ oses . All parts such as nuts , IMPORTANT : Unfoldhandles carefullyso as washers , bolts , etc . , necessary to complete the not to pinch or damage controlcables . assembly have been placed inthe parts hag . To entre safe and proper operation of your • Raise handles until lower handle section lawn mower , all parts and hardware you locks into place in mowing position . assemble must be tightdnedsecurely . Use the • Remove protective padding , raise upper correct tools as necessary to ensure proper handle section into placa on lower handle tJghthess . and tighten both handle knobs . • Remove handle padding holding operator TO REMOVE LAWN MOWER FROM presence control bar to upper handle . CARTON • Your lawn mower handle can be adjusted • Remove louse parts includedwith mower . for your mowing comfort . Refer to " Adjust • Cut down two end comers of carton and lay Handle " in the Service and Adjustment end panel down flat . sec'don of this manual . • Remove all packing materials except padding betv _ een upper and lower handle and padding holding operator presence control bar to upper handle . 4
Page: 5

TO INSTALL A'n'ACHMENTS bar Your lawn mower was shipped ready to be U used as a mulcher . To convertto bagging or L . iftup discharging : • Open rear door and remove mulcher plug . Store mulcher plug ina safe place . • You can now installcatcher or optional Mowing dipping deflector . position • To retum to mulchingoperation , install mulcher plug intodischarge opening of mower . Be sure alltabs are seated prope y . Lowerhandle Mulcher plug _ & CAUTION : Do not run your lawn mower without mulcher plug in place or approved clipping deflector or grass catcher in place . Never attempt to operate the lawn mower with the rear door removed or propped open . 5
Page: 6

KNOWYOURLAWNMOWER READ THIS OWNER'S MANUALAND SAFETY RULES BEFORE OPERATING YOUR LAWN MOWER . Compare the illustrationswithyour lawn mower to familiarize yourself withthe locationof variouscontrols and adiustmonts . Save this manual for future reference . _ symlx31msayappearonyourlawnrnowerorInIlteraUe = . , pldledwnhtheproductL . ean a ' , , dunderstand theren _ g . CAUTION ENGINE ENGINE FAST SLOW CHOKE FUEL OIL DANGER , KEEP HANDS OR WARNING ON OFF AND FEET AWAY Enginezone controlcable Operatorpresence controlbar Drive control lever Srarter handle Handleknob Mulcher plug Gasolinecap . . " Primer Housing Engineoil cap w / dipstick Wheel adjuster ( on eachwheel ) MEETS CPSC SAFETY REQUIREMENTS Sears rotarywalk - behind power lawn mowers conformto the safetystandards of the American National Standards Instituteand the U . S , Consumer ProductSafety Commission . The blade turns when the engine is nJnning . Drive control lever - used to engage power - Operator presence control bar - must be propelled forward motion of lawn mower . held down to the handle to startthe engine . Mulcher plug - must be removed to convert to Release to stopthe engine . bagging or dischargingoperation . Primer - pumps addlfJonalfuel from the carburetorto the cylinderfor use when starling a cold engine . Starter handle - used for startingthe engine . 6
Page: 7

TO ATrACH GRASS CATCHER The operation of any lawn mower can result in foreign objects thrown into the • Close the fliplid . Rip lid must be dosed eyes , which can result in severe eye while operaUnglawn mower . damage . Always wear safety glasses or • Liftthe reardoor on the mower housingand eye shields while operating your lawn place the grasscatcher frame onto the mower or performing any adjustments or formed tabs onthe rear door hinge bracket . repairs . We recommend a wide vision • The grass catcher is secured to the lawn safety mask over spectacles or standard mower housingwhen the rear door is safety glasses . lowered onto the grass catcher frame . HOW TO USE YOUR LAWN MOWER ACAUTION - Do not run your lawn mower ENGINE SPEED without clipping deflector or approved grass catcher in place . Never attempt to The engine speed was set at the factory operate the lawn mower with the rear door for optimum performance . Speed is not removed or propped open . adjustable . ENGINE ZONE CONTROL Hinge Rear door ACAUTION : Federal regulations require an engine control to be installed on rthisisk Grass catcher lawn mower in order to minimize the of frame blade contact injury . Do not under any circumstances attempt to defeat the function of the operator control . The blade turns when the engine is running . Formed • Your lawn mower is equipped with an tabs operator presence controlbar which reqdires the operator to be positionedtart TO EMPTY GRASS CATCHER behind the lawn mower handle to s and • To remove grass catcher , release operator operate the lawn mower . presence controlbar to stop engine . TO ADJUST cUTrlNG HEIGHT • Uft up rear door and remove the grass • Raise wheels for low cut and lower wheels catcher by the handle . for high cut . NOTE : Do not drag the bag when • Adjust cutting height to suit your require - emptying ; it will cause unnecessary wear . ments . Medium posiUon is best for most lawns . • To change cuttingheight , squeeze adjuster lover toward wheel . Move wheel up or down to suityour requirements . Be sure all wheels are inthe same setting . NOTE : Adjustor is propedy positioned when plate tab inserts into hole in lever . Also , 9 - position adjusters ( if so equipped ) allow lever to be positioned between the plate tabs . Plate Tab Lower Wheels for High Lever Raise Wheels for LowCut 7
Page: 8

DRIVECONTROL GAS • Self - propellinigscontrolledbyholding • RII fuel tank . Use fresh , clean , regular theoperatorpresencecontrolbardown unleaded gasoline witha minimum of 87 to thehandleandpushingthedrive octane . Do not mix oilwith gasoline . controlleverforward until it clicks ; then Purchase fuel inquan'trtiesthat can be used release the lever . within30 days to assure fuel freshness . • Forward motion will stop when the WARNING : Experience indicatesthat alcohol operator presence control bar is blended fuels ( called gasohol or using ethanol released . To stop forward motion or methanol ) can attract moisturewhich leads without stopping engine , release the to separation and formation of acids during operator presence control bar slightly storage . Acidicgas can damage the fuel until the drive control disengages . Hold system of an engine while instorage . To avoid operator presence control bar down to engine problems , the fuelsystem should be handle to continue mowing without self - emptied before storage of 30 days or longer . propelling . Drain the gas tank , startthe engine and let it run untilthe fuel lines and carburetorare • To keep drive control engaged when turning comers , push down on handle empty . Use fresh fuel next season . See and lift front wheels off ground while Storage Instructionsfor addRionalinformation . turning lawn mower . Never use engine or carburetorcleaner productsin the fuel tank or permanent Operatorpresencecontrolbar Ddve damage may occur . " _ control Engineoil cap Gasolinefillercap To engage drive Drive control control disengaged BEFORE STARTING ENGINE OIL Your lawn mower is shipped withoutoil in the TO START ENGINE engiRe . • Be sure mower is level and area around oil • To stad a cold engine , push primerfive ( 5 ) fillis ctean . times before tryingto start . Use afirm push . • Remove engine oilcap and fillto the full line This step is not usually necessary when on the dipstick . startingan engine which has already run for a few minutes . • Use 20 ozs . of oil . For type and grade of oil • Hold operator presence control bar down to to use , see " ENGINE " in Maintenance ssction of this manual . the handte and pullstarter handle quiddy . Do not allow starter rope to snap beck . • Pouroil slowly . Do not overfill . • Check oil level before each use . Add oilif • To stop engine , release operator presence control bar . needed . Fillto full lineon dipstick . NOTE : In cooler weather it may be • To read proper level , tighten engine oil cap each time . necessary to repeat priming steps . In warmer weather over priming may cause • Reinstall engine oil cap and tighten . • Change the oilafter every 25 hou _ of flooding and engine will not start . If you do flood engine , wait a few minutes before operation or each season . You may need attempting to start and do not repeat to change the oilmore often under dusty , priming steps . dirtyconditions .
Page: 9

_ IOWING TIPS MULCHING MOWING TIPS Under certain conditions , such as very IMPORTANT : For best parformance , keep tall grass , it may be necessary to raise mower housingfree of built - upgrass and the height of cut to reduce pushing effort trash . See = Cleaning " in Maintenance section ofthis manual . and to keep from overloading the engine and leaving clumps of grass clippings . It • The special mulching blade will recut the may also be necessary to reduce ground grass clippingsmany times and reduce speed and / or run the lawn mower over them in size so that as they fall onto the the area a second time . lawn they willdisperse into the grassand For extremely heavy cutting , reduce the not be noticed . Also , the mulched grass will width of cut by overlapping previously cut biodegrede quickly to provide nutrientsfor path and mow slowly . the lawn . Always mulch with your highest For better grass bagging and most engine ( blade ) speed as this will providethe cutting conditions , the engine speed best recurringa _ on of the blades . should be set in the fast position . • Avotd cuttingyour lawn when it iswet . Wet When using a rear discharge lawn grass tends to form dumps and interferes mower in moist , heavy grass , clumps of with the mulchingaction . The best time to cut grass may not enter the grass mow your lawn is the early afternoon . At catcher , Reduce ground speed ( pushing this time the grass has dried and the newly speed ) and / or run the lawn mower over cut area will not be exposed to the direct the area a second time . sun . If a trail of clippings is left on the right • For best results , adjust the lawn mower side of a rear discharge mower , mow in a cuttingheightso that the lawn mower cuts clockwise direction with a small overlap off only the top one - third of the grass blades . to collect the clippings on the next pass . If the lawn is overgrown it will be necessary Pores in cloth grass catchers can to raise the heightof cut to reduce pushing become filled with dirt and dust with use effortand to keep from overloading the and catchers will collect less grass . To engine and leaving clumps of mulched prevent this , regularly hose catcher off grass . For extremely heavy mulching , with water and let dry before using . reduce your wicl _ of cut by overlapping Keep top of engine around starter clear previouslycut path and mow slowly . and clean of grass clippings and chaff . • Certain types of grass and grass conddions This will help engine air flow and extend may requirethat an area be mulched a engine life . second time to completely hide the clippings . When doing a second cut , mow acrossor perpendicularto the firstcut path . • Change your cuttingpattern from week to week . Mow nodh to south one week then change to east to west the next week . This will help prevent matting and graining of the lawn . / 3 9
Page: 10

MAINTENANCESCHEDULE i _ , _ . _ _ _ , O _ ' _ / ' I " REGULARSERVICE / _ " _ O ? , _ , _ . - _ SERVICE nDATES mill / _ Check for Loose Fasteners I / If Clean / Inspect Grass Catcher ( if Equipped ) _ ' / ! _ i 1 / M clean , - weMower _ If ( Power - Propalled Mowers ) I , / W _ Clean UnderDriveCover Checkdrivebelt / pulleys RE ( powe r - PropelledMowers ) Check / Sharpen / Replace Blade 1 / 3 Lubrication Chart I , / I _ Cleon Battery / Recharge IElectric Start Mowers I If I / 4 E Check Engine Oil Level 1 / N Change Engine Oil 1 / 1.2 G Clean Air Filter 1 / z i Inspect Muffler N Clean or Replace Spark Plug E Replace Air Filter Paper Carlddge 1 / 2 1 - Change morn _ wh4moperating under = heavy load or in high ambient temperaturN . 2 - S _ ' V _ e more oflml when operaling kl d _ or du _ y condi ¢ oe = . 3 - I _ place Idadee more oaen when mowing ia = umd , / = all 4 - Charge 48 hoursat m ) d of SellOn , GENERAL RECOMMENDATIONS LUBRICATION CHART The warranty on this lawn mower does not ( _ ) Wheel cover items that have been subjected to adjuster ( _ ) Engine operator abuse or negligence . To receive oil full value from the warranty , operator must maintain mower as instructed in this manual . Some adjustments will need to be made periodically to properly maintain your unit . All adjustments in the Service and Adjustments section of this manual should be checked at least once each season . • Once a year , replace the spark plug , Brake replace air filter element and check spring blade for wear . A new spark plug and clean / new air filter element assures _ ) Rear door bra _ et proper air - fuel mixture and helps your hinge ( _ Handlebracket engine run better and last longer . mountingpin • Follow the maintenance schedule in this ® Spray manual . BEFORE EACH USE ( _ Referto Maintenance " ENGINE " section . • Check engine oil level . • Check for loose fasteners . LUBRICATION IMPORTANT : Do not oilor grease plastic wheel bearings . Viscous lubricantswill attract Keep unit well lubricated ( See " LUBRICA - dust and dirtthat will shortenthe lifeof the self TION CHART " ) . lubricatingbearings . If you feel they must be lubricated , use only a dry , powdered graphite type lubricantsparingly . 10
Page: 11

PRODUCT SPECIFICATIONS MODEL NUMBER 917.377543 ; ERIAL NUMBER DATE OF PURCHASE HORSEPOWER : 6.5 DISPLACEMENT : 11.5 CU . IN . GASOLINE CAPACITY / TYPE : 1.25 QUARTS UN5LEADED REGULAR OIL TYPE ( API - SF / SG / SH ) : SAE 30 ( ABOVE 32 ° F ) SAE 5W - 30 ( BELOW 32 ° F ) OIL CAPACITY : 20 OZS . SPARK PLUG ( GAP : . 030 " ) CHAMPION RJ19LM OR J19LM VALVE CLEARANCE : INTAKE : . 004 - . 008 EXHAUST : . 004 - . 008 SOLID STATE IGNITION AIR GAP : . 0125 IN . BLADE BOLT TORQUE : 35 - 40 FT . LBS . The model and sedal numbers will be found on a decal attached to the rear of the lawn mower housing . Record both serial number and date of purchase in space provided above . LAWN MOWER clockwise . Always observe safety rules when performing • Remove blade and attaching hardware any maintenance . ( bolt , lock washer and hardened TIRES washer ) . • Keep tiresfree of gasoline , oil , or insect NOTE : Remove the blade adapter and controlchemicals which can harm rubber . check the key inside hub of blade adapter . • Avoid stumps , stones , deep ruts , sharp The key must be in good condition to work objects and other hazards that may cause properly . Replace adapter if damaged . tire damage . TO REPLACE BLADE BLADE CARE • Position the blade adapter on the engine For best results , mower blade must be crankshaft . Be sure key in adapter and kept sharp . Replace bent or damaged crankshaft keyway are aligned . blades . - • Position blade on the blade adapter TO REMOVE BLADE aligning the two ( 2 ) holes in the blade • Disconnect spark plug wire from spark with the raised lugs on the adapter . plug and place wire where it cannot • Be sure the trailing edge of blade come in contact with spark plug . ( opposite sharp edge ) is up toward the • Turn lawn mower on its side . Make sure engine . air filter and carburetor are up . • Install the blade bolt with the lock • Use a wood block between blade and washer and hardened washer into blade mower housing to prevent blade from adapter and crankshaft . • Use block of wood between blade and turning when removing blade bolt . • Protect your hands with gloves and / or lawn mower housing and tighten the wrap blade with heavy cloth . blade bolt , turning clockwise . • Remove blade bolt by turning counter - • The recommended tightening torque is 35 - 40 ft . Ibs . 11
Page: 12

IMPORTANT : Blade bolt is grade 8 heat • Remove any trash or grass cuttings from treated . inside the dust cover , pinion and / or drive wheel gear teeth . TO SHARPEN BLADE • Put wheels back in place . NOTE : We do not recommend sharpening • If after cleaning , the drive wheels do not blade - but if you do , be sure the blade is turn freely , contact your nearest balanced . authorized service center . Care should be taken to keep the blade GEAR CASE balanced . An unbalanced blade will cause • To keep your drive system working eventual damage to lawn mower or properly , the gear case and area around engine . the drive should be kept clean and free • The blade can be sharpened with a file of trash build - up . Clean under the drive or on a grinding wheel . Do not attempt cover twice a season . to sharpen while on the mower . • The gear case is filled with lubricant to • To check blade balance , drive a nail into the proper level at the factory . The only a beam or wall . Leave about one inch of time the lubricant needs attention is if the straight nail exposed . Place center service has been performed on the gear hole of blade over the head of the nail . case . If blade is balanced , it should remain in • If lubricant is required , use only Texaco a horizontal position . If either end of the Starplex Premium 1 Grease , Part No . blade moves downward , sharpen the 750369 . Do not substitute . heavy end until the blade is balanced . ENGINE Blade Crank shaft keyway LUBRICATION Blade Use only high quality detergent oil rated with API service classification SF , SG or SH . Select the oil's SAE viscosity grade according to your expected operating temperature . bolt shaft Lock Blade washer Hardened edge adapter washer GRASS CATCHER • The grass catcher may be hosed with NOTE : Although multi - viscosity oils water , but must be dry when used . ( 5W30 , 10W30 etc . ) improve starting in • Check your grass catcher oftenfor damage or deterioraUon . Through normal use itwill cold weather , these multi - viscosity 0ils wear . If catcher needs replacing , replace will result in increased oil consumption only with a manufacturer approved when used above 32 ° F . Check your replacement catcher . Give the lawn mower engine oil level more frequently to avoid model number when ordering . possible engine damage from running low on oil . DRIVE WHEELS Check front drive wheels each time before Change the oil after every 25 hours of you mow to be sure they move freely . operation or at least once a year if thein The wheels not turning freely means trash , lawn mower is not used for 25 hours grass cuttings , etc . are in the drive wheel one year , area and must be cleaned to free drive Check the crankcase oil level before wheels . If necessary to clean the drive wheels , starting the engine and after each five check both fro _ t wheels . ( 5 ) hours of continuous use . Tighten oil • Remove hubcaps , hairpin cotters and plug securely each time you check the washers . oil level . • Remove wheels from wheel adjusters . 12
Page: 13

MUFFLER TOCHANGEENGINEOIL Inspect and replace corroded muffleras it NOTE : Beforetippinglawnmowerto drain couldcreate a fire hazard and / or damage . oil , drainfuel tank by running engine until SPARK PLUG fuel tank is empty . Change your sparkplug each year to make • Disconnect spark plug wire from spark plug your engine start eas ' _ r and run better . Set and place wire where itcannot come in spark plug gap at . 030 inch . contact with spark plug . CLEANING • Remove engine oilcap ; lay aside on a dean IMPORTANT : For best performance , keep surface . mower housing free of built - up grass and • T ' _ olawn mower on its side as shown and trash . Clean the underside of your mower drain oil into a suitable container . Rock lawn after each use . mower back and forth to remove any oil ACAUTION : Disconnect spark plug wire t _ insideof engine . from spark plug and place wire where it • W ' _ oeoff any spilled oil on lawn mower and cannot come in contact with the spark on side of engine . plug . • Fillengine with oil . Fillonly to the = FULL " • Tum lawn mower on its side . Make sure air line on the dipstick . DO NOT overfill . • Replace engine oilcap . filterand carburetorare up . Clean the • Reconnect spark plug wire to spark plug . undersideofyourlawnmower byscraping toremovebuild - uopfgrassandtrash . • Clean engine oftento keep trash from accumulating . A dogged engine runs hotter and shortens engine life . Container • Keep finishedsurfacas and wheels free of all gasoline , oil , etc . AIR FILTER • Wedonot recommend usinga garden hose to clean lawn mower unless the Your engine will not run properly and may be damaged by using a dirty air filter . electricalsystem , muffler , air filterand Replace the air filter every year , more carburetor are covered to keep water out . often if you mow in very dusty , dirty Water in engine can resultinshortened conditions . Do not wash air filter . engine life . CLEAN UNDER DRIVE COVER TO CHANGE AIR FILTER Clean underddve cover at least twlee a • Remove the air filter by tuming clock - season . Scrapa underside of cover with putty wise to the stop and pull away from I _ ife or similartool to remove any build - upof collar . trash or grasson underside of drive cover . • Remove filter from inside of cover . • Clean the inside of the cover and the collar to remove any dirt accumulation . • Insert new filter into cover . • Put air filter cover and filter into collar aligning the tab with the slot . • Push in on cover and tum counterclock - wise to tighten . Collar Remove Slot " rum Tab Counter - Air Filter Air Filter Clockwise to Cover Tighten 13
Page: 14

• Remove the starterrope guidefrom the ACAUTION : Before performing any upper handle . service and adjustments : • Remove hairpincotters . • Release control bar and stop engine . • Disconnectthe lower handle from the • Make sure the blade and all moving handle brackets . parts have completely stopped . • Turn the handle over and reassemble the • Disconnect spark plug wire from spark hairpin cotters that have been removed . plug and place where it cannot come • Reassemble the starter rope guide . in contact with plug . • Reassemble the controls and the operator LAWN MOWER presence controlbar to _ upper handle . TO ADJUST CUTTING HEIGHT ACAUTION : The operator presence See " TO ADJUST CUTTING HEIGHT " in the control bar must pivot freely to permit Operation sectionof this manual . blade brake engagement when control bar REAR DEFLECTOR is released . Do not over tighten the The rear deflector , attached between the rear fasteners holding the controls to the upper handle . wheels of your lawn mower , is providedto minimize the possibilitythat objects will be • To change from medium low to high thrown out the rear of the lawn mower intothe positiononly the upper handle section will operator's mowing position , ffthe rear have to be tumed over . deflectorbecomes d _ na _ d , it should be • To change from medium towto lew posi _ on , replaced . only the lower handle section will have to be TO REMOVE / REPLACE DRIVE BELT turned over . • Remove drive cover . Remove belt by Shippit _ jposition pushing down on gear case pulleyand roll Mediumlow belt off . • Tum lawn mower on its side with carburetor and fuel cep up . • Remove blade . • Remove debris shield . • Remove belt from engine pulley on crankshaft . high • Installnew belt by reversingabove stepe . • Always use factoryapproved beltto assure and Ufe . Dd : : rBe _ _ High _ ow TOouAaDJmwSnTUowH , rND _ ie _ canbe raised or Y _ _ _ " _ _ lowered foryour mowing comfort . Four ( 4 ) Lower handle positionsare available : high , medium high , medium lowand low . Handles are shipped mounted inthe medium lowpos ' _ ion . • To change from medium low to medium Squeeze to _ high position , the upper and lower handle sectionswill have to be tumed over . • Remove the cable dips . • Remove the controls and operator presence control bar from the upper handle . bracket 14
Page: 15

ENGINE SPEED Sewn Tubular frame hem Your engine speed has been factory set . Do not attempt to increase engine speed or it may result in personal injury . If you believe that the engine is running too fast or too slow , take your lawn mower to an authorized service center for repair and adjustment . CARBURETOR Your carburetor has a non - adjustable fixed main jet for mixture control . If your engine Sewn hem Rip lid does not operate propedy due to sus - pected carburetor problems , take your lawn mower to an authorized service Lower frame center for repair and / or adjustment . ( Frames TO ASSEMBLE GRASS CATCHER mustbe • Insert leg of tubular frame through front fully opening of grass catcher and thread seated ) frame into sewn hem of bag . NOTE : Keep bag hem gathered on the straight leg of the tubular frame . • When frame comes out the other end of sewn hem , immediately work the end of Tubularframe frame down inside the bag as shown in inset . • Slide sewn hem evenly around the tubular frame until both ends of frame are exposed out of the front opening . Lowerframe handle • Assemble lower frame to tubular frame as shown . Be sure handle is outside of bag and frames are fully seated as shown in inset . • Slip vinyl bindings over frame . NOTE : If vinyl bindings are too stiff , hold them in warm water for a few minutes . If \ Vinyl " _ bag gets wet , let it dry before using . • Close the flip lid . Flip lid must be closed while operating lawn mower . ACAUTION : Do not run your lawn mower without clipping deflector or approved grass catcher in place . Never attempt to operate the lawn mower with the rear door removed or propped open : 15
Page: 16

control bar / Upper Operatorpresence . _ _ / . handle Immediately prepare your lawn mower for storage at the end of the season or ifthe unit Fold forward / / . / / _ , ( ' _ " _ , _ will not be used for 30 days or more . LAWN MOWER When lawn mower is to be stored for a period of time , clean it thoroughly , remove all dirt , grease , leaves , eto . Store in a dean , dry area . I backward • Clean entire lawn mower ( See " CLEANING " . . . . . % \ _ - - _ , " l Lower _ Mov _ ingposition inthe Maintenance section of thismanual ) . • Lubricate as shown inthe Maintenance handle section of this manual . • Be sure that all nuts , bolts , screws , and pins ENGINE are securely fastened . Inspect moving FUEL SYSTEM parts for damage , breakage and wear IMPORTANT : Itis important to prevent gum Replace if necessary . depositsfrom forming in essential fuel system • Touch up all rusted or chipped paint parts such as carburetor , f fuel tilter , fuel hose surfaces ; sand lightlybefore painting or tank during storage . Aleo , exper _ eoce HANDLE indicatesthat alcohol blended fuels ( called You can fold your lawn mower handle for gasohol or usingethanol or methanol ) can storage . attract moisturewhich leads to separation and • Squeeze the bottom ends of the lower formation of acids duringstorage . Acidicgas handle toward each other untilthe lower can damage the fuel system of an engine handle dears the handle bracket , then while instorage . move handle forward . • Drain the fuel tank . • Loosen upper handle mountingbolts • Stad the engine and let it n . _ untilthe fuel enough to allow upper handle to be folded lines and carburetor are empty . beck • Never use engina or carburetor cleaner IMPORTANT : When foldingthe handle for products in the fuel tank or permanent storage or transportation , be sure to foldthe damage may occur . handle as shown oryou any damage the • Use fresh fuel next seeson . controlcables . NOTE : Fuel stabilizeris an acceptable • When setting up your handle from the aitemative inminimizing the formation of fuel storage position , the lower handle will gum deposits during storage . Add stabilizerto automatically lockinto the mowing position gasoline in fueltank or storage container . Always followthe mix ratiofound on stabilizer container . Run engine at least 10 minutes after adding stabilizerto allow the stabilizerto reach the carburetor . Do not drain the gas Handle tank and carburetorif usingfuel stabilizer . Squeeze to fold bracket Hai @ n cotter 16
Page: 17

ENGINEOIL • If possible , store your unit indoorsand cover Drainoil ( withenginewarma ) ndreplacewith it to give protection from dust and dirt . deanengineoil . ( See " ENGINEi " nthe • Cover your unitwith a suitableprotective cover that does not retain moisture . Do not Maintenancseectionofthis manual ) . CYUNDER use plastic . Plasticcannot breathe which allows condensation to form and will cause • Remove spark plug . • Pour one ounce ( 29 ml ) of oilthrough spark your unitto rust . IMPORTANT : Never cover mower while plughole into cylinder . • Pull starter handle slowly a few times to engine and exhaust areas are stillwarm . distributeoil . ACAUTION : Never store the lawn mower • Replace with new spark plug . with gasoline in the tank inside a building OTHER where fumes may reach an open flame or • DO not store gasoline from one season to spark . Allow the engine to cool before another . storing in any enclosure . • Replace your gasoline can ifyour can starts to rust . Rust and / ordirtin your gasoline will cause problems . TROUBLESHOOTING CHART PROBLEM CAUSE CORRECTION Does not start • Dirty air fiifer . • Clean / replace air fiifer . • Out of fuel . • RII fuel tank . • Stale fuel . • Drain tank and refillwith fresh dean fuel . • Water infuel . • Drain fuel tank and carburetorand refilltank withfresh gasoline . • Sparkplug wire is • Connect wire to plug . disconnected . • Badsparkplug . • Replace spark plug . • Loosebladeor brokenblade • T _ ghtenblade bolt or adapter . replace blade adapter . • Controlbarin released • Depress controlbar to handle . position . • - Controbl ardefective . • Replace control bar . 17
Page: 18

TROUBLESHOOTING CHART CAUSE CORRECTION PROBLEM • Rear of lawn mower housing • Satto " Higher Cut " Loss of power or cutting blade dragging pos'dion . in heavy grass . • Bet to = HigherCut " • Cutting too much grass . position . • Clean / replace air filter . • Dirty airfilter . • Clean undersideof mower • Buildupof grass , leaves , and trash under mower . housing . • Check oillevel . • Too m _ - ' h oil in engine . • Waildng speed too fast . • Cut at slower walking speed . Poor cut - uneven • Wom , bent or loose blade . • Replace blade . T _ jhten blade belt . • Set all wheels at same • Wheel heights uneven . height • Clean undersideof • Buildup of grass , leaves and trash under mower . mower housing . Excessive • Wom , bent or loose blade . • Replace blade . T _ htan blade bolt . vibration • Contact an authorized • Bent engine crankshaft . service center . • Depress control barto • Engine flywheel brake is on Starter rope hard when control bar is released . upper handle before to pull pullingstarter rope ; • Contact an authorized • Bent engine crankshaft . service center . • Blade adapter broken . • Replace blade adapter . • Move lawn mower to cut • Blade dragging in grass . grass orto hard surface to start engine . Grass catcher • Raise cuttingheight . • Cuffing height tee low . • Lifton blade wom off . • Replace blade . not filling ( ffso • Catcher notventing air . • Clean grass catcher . equipped ) • Raise cutting height . Hard to push • Grass is too highor wheal heightis tee low . • Rear of lawn mower • Raise rearof lawn mower housingone ( 1 ) setting housing or blade dragging higher . in grass . • Grass catcher too full . • Empty grasscatcher . • Adjust handle heightto • Handle height positionnot suit . rightfor you . 18
Page: 19

) 651o ROTARY LAWN MOWER - - MODEL NO . 917.377543 GEAR CASE ASSEMBLY PART NUMBER 702511 14 KEY PART KEY PART NO . NO . DESCRIPTION NO , NO . DESCRIPTION - 1 17490416 Tapping Screw 114 - 20 x 9 137074 Drive Shaft 1 - 1 / 4 10 57079 Hardened Washer 2 137055X004 . ' _ Engagement Bracket 11 131484 Clutch Yoke 3 137053 Shifter 12 700343 Bushing 4 57072 Seal 13 86447 Plug 6 48373 Gear Case Halves Kit 14 137050 Helical Gear ( InCludeS Key Nos . 4 , 5 , 15 750436X Clutch Jaw and 7 ) 16 750369 Grease 7 77881 Beadng 17 12000003 E - Ring 8 137051 Worm Shaft 18 850848 Hi - Pro Key 19 S1585X004 Spring Bracket NOTE : All component dimensions given in U . S . inches , 1 inch = 25.4 mm 37
Page: 20

38
Page: 21

ROTARY LAWN MOWER MODEL NUMBER 917.377543 KEy PART KEY PART NO . NO . DESCRIPTION NO . NO . DESCRIP _ ON 1 165451X479 41 1504O6 UpperHandle Hex Head Thread Rolling Screw 3 / 8 - 16 ) ( 1 - 1 / B 2 166577 44 161769 MEngtnZeone ControlCable Lawn Mower Housing ( JncL Key # 14 , 15 , 51 ) 4 15O425 46 851514 ulcherPlug Blade Adapter WireTie 6 66426 47 157101 Blade 22 " 6 136376 48 851074 Hardened Washer LHandta Knob 8 145793 ControlBar 49 850263 Helicet Washer 3 / 8 - 24 x I • 3 / 8 Gr , 8 151023 Rear DoorKit g 50 851084 Hex Head Machine Screw 3 / 8 - 24 x 1 - 3 / 8 Gr . 6 128415 10 51 165548 Front Baffle PopRivetpingScrew 11 13O03O 52 85463 Se _ fTap # 10 - 24x 5 / 8 Danger Decal STD512505 12 Hex TappingScreww / scms 1 / 4 - 20 x 1 / 2 55 751592 Locknut 3 / 8 - 16 13 77400 Hubcap 56 88652 Hinge Screw 1 / 4 - 20 x 1 - 1 / 4 14 156374X479 Backplata 57 51793 Hairpin Cotter 15 7003O5X479 Side Baffle 58 157081X479 Lower Handle co 16 133190X479 DischargeBaffle 59 131959 Handle Bolt CD 17 140661X479 Rear Baffle 61 132001 Rope [ Guide 18 636O1 Kep = Locknut1 / 4 - 20 62 134612 Debds Sh eJd 2O 14O54O Rear Skirt 64 . . . . . . Engine - ( See Breakdown ) 22 85543 Tecumseh Model No , 143.996510 EnginePulley # 23 67677 Hi - ProKey 506 - - 161058 Warning Decal ( Not Shown ) 25 83923 • . 166080 Hex FlangeNet Owner's Manual ( Englis _ Spanish ) 27 151158 Wheel 28 142748 Shoulder Bolt 3 / 8 - 16 x 1 Available accessories not included with lawn mower : 29 62335 BetlevilleWeshar . . 71 33303 Clipping Detlectot 3O 145S35X004 AxleAm1 . . 71 33623 Gas Can ( 2,6 gal . ) 31 701037 Selector Knob • . 71 33500 Fuei StabiJIzer 32 73O331X004 Setecto ¢ Spdng - . 71 33300 SAE 3OW Oil ( 20 oz . ) 34 14663O Spacer - . 71 33417 Dust Shield 35 700 _ ? . 6X607 WheelAdjustingBracket - . 7133316 Mower Cover 37 150078 ThreadCuttingScreww / Barns5 / 16 - 18x 3 / 4 - . 71 33723 High Wheel Kit 39 151512X479 HandleBracketAssembly ( Left ) 4O 151511x47g HandleBcacketAssembly ( Right )
Page: 22

40
Page: 23

ROTARY LAWN MOWER MODEL NUMBER 917.377543 KEY PART KEY PART NO . NO . DESCRIPTION NO , NO . DESCRIPTION _ " 28 154990 Drive Cover 1 145755 C _ trOI Cable Assembly 31 132010 Hex Flange Nut 3 751152 Locknut # 10 - 24 32 137052 Ddve Pulley 4 158755 Pan Head Machine Screw 1 / 4 x 2,12 35 151521 Wheel Adjuster Assemb ; y ( Left ) 5 145527 V - _ t 36 702511 Gear Case Assembly 6 150495 Spring Retainer 37 137090 Spring 5 77400 , Hubcap 38 63601 Nut 9 145212 Flanged Nut 40 75192 Spring 11 151156 Wheel & Tire AssembJy 41 151520 Wheel Adjuster Assembly ( Right ) 12 12000058 E - Ring 53 144747 Frame Throat 13 137054 Pinion 54 166069 Grassheg Assembly 14 88080 Dust Cover 55 86012 Drivechaft Cove , , 15 88118 Felt Weeher 57 144748 Gmssheg Tube 16 67725 Washer 1 / 2 x 1 - 1 / 2 x , 134 15 701037 Selector Knob 26 143603 Pan Heed Tapping Screw # 10 - 24 x 2 - 3 / 4
Page: 24

CRAFTSMAN 4 - CYCLE ENGINE MODEL NO , 143.996510 292 . 285 290 400 130 120 11g 416 ] 18 19 174 73 238 250 42
Page: 25

MODEL NO . 143.996510 CRAFTSMAN 4 - CYCLE ENGINE KEY PART KEY PART NO . NO . DESCRIPTION NO . NO . DESCRIPTION 1 37266 Cylinder ( Incl . 2,20 & 150 ) t50 31672 Valve Swing 2 26727 Dowel Pin t61 31673 Valve Spring Cap 6 33734 Breather Element 151A 40017 Intake Valve Seal 7 36557 Breather Ass _ / . ( incl . 6 & 12A ) 169 36783 * Valve Cover Gasket 12 36775 Breatber Tube t72 36784 Valve Cover 12A 36658 Breather Cover & Tube ( Incl . t74 30200 Screw , 10 - 24 x 9 / 16 " 12B ) t78 29752 Nut & Lock Washar , 1 / 4 - 28 12B 36694 Breather Tube Elbow t 82 6201 Screw , 1 / 4 - 28 x 7 / 8 " 14 28277 Washer 184 26756 • Carburetor To Intake Pipe Gasket 15 30589 Governo _ Rod ( Incl . 14 ) 185 36785 intake PipeLink 16 34839A Govemo _ Lever 186 32653 Govemor 17 31335 Governor L _ Ner Clamp 189 650839 Screw , 1 / 4 - 20 x 3 / 8 " 18 651618 Screw , To ( x T - 15 , 8 - 32 x 19 191 36559A S . E . Brake Bracket ( Incl . 196 ) 64 " 195 610973 Terminal 19 36281 Extension Spring 207 34336 Throtfte Link 20 32600 Oil Seal 216 33086 R . P . M . Adjusting Lever 30 35801 Crankshaft 223 650451 Screw , 1 / 4 - 20 x 1 " 40 40027 Piston , Pin & Ring Set ( Std . ) 224 36766 " Intake Pipe Gasket 40028 Piston , Pin & Ring Set ( . 010 " 238 650932 Screw , 10 - 32 x 49 / 64 " OS ) 239 34336 " Air Cleaner Gasket 41 40025 Piston & Pin Ass _ / , ( Std . ) { Incl . 241 36918 Air Cleaner Cut ] rar 43 ) 245 36905 Air Cleaner Filte 40026 Piston & Pin Ass _ . . ( . 010 " OS ) 250 36 _ 0 Air Cleaner Cover ( Incl . 43 ) 260 36980 Blower Housing 42 40006 Ring Set ( Std , ! . 261 30200 Screw , 10 - 24 x 9 / 16 " " 40007 Ring Set ( . 010 OS ) 262 650831 Screw , 1 / 4 - 20 x 1 / 2 43 20381 Piston Pin Retaining Ring 263A 36921 Starter Grill 45 36777 Connec _ ng Rod ASS'y . ( Incl . 275 36790A Muffler 46 ) 277 650988 Screw , 1 / 4 - 20 x 2 - 5 / 16 " 46 32610A Connecting Rod Bolt 285 35000A Starter Cup32 48 27241 Valve L _ ter 287 650926 Screw , 8 - x 21 / 64 " SO 36778 Camshaft ( MCR ) 2gO 29774 Fuel 52 29914 Oit Pump / _ ss _ / . 292 26460 Fuel Line Clamp 69 35261 * Mounting Flange Gasket 298 28763 Screw , 10 - 32 x 35 / 64 " 70 34311E Mounting Flange ( Ind . 72 thru 300 36916 Fuel Tank { Ind . 292 & 301 ) 83,306 ) 301 36246 Fuel Cap 72 30572 Oil Drain Plug ( thcl . 73 ) 305 35647 Oil Fill Tube 73 28833 Drain Plug Gasket 306 36996 • " O - Ringog 75 27897 O _ Seal 307 35499 " ( _ - Rt 80 30574A Governor Shaft 309 650562 Screw , 10 - 32 x 1 / 2 " 81 30590A Washer 310 35648 Dips6dx 82 30591 Governor Gear Ass " / . ( Ind . 61 ) 313 34080 Spacer 83 30588A Governor Spool 347 651038 Screw , 10 - 32 x 51 / 64 " 86 650488 Screw , 114 - 20 x 1 - 1 / 4 " 370A 36261 LubdcaKon Decal 89 611004 Rywbeel Key 370C 37199 Primer Dotal 90 611112 P " l _ heel 380 640174 Car _ ( IrmL 184 ) 92 650815 Sellevllle Washer 3 _ O 590739 Rewind Starter 93 650616 Flywheel Nut 400 36792B Gasket Set ( Incl . Items 100 34443B - Solid State Ignition Marked " ) 101 610116 Spark Pleg Covet 416 36 _ 85 Sflark Attestor lot ( Ind . 417 ) f03 651007 Screw , Torx T - 15 , 10 - 24 x 15 / ( Op _ onal ) 16 " 417 65 _ 21 Screw , 10 - 32 x 1 / 2 " ( Op _ onal ) 110 37047 Ground Wire 900 - - - - Replacement Engine NONE 119 36787 * C ' / 6nder Read Gasket 9GO - - - - Reptacement S / B 750832A , ocder f2O 36825 Cylinder Head from 71 - 999 125 37288 Exhaust Valve ( Std . ) ( Ind . 161 ) - - _ RPM High 2900 to 3200 126 37289 Intake Valve ( Ski . ( Incl . 151 ) 30 6021A Screw , 5 / 6 - 18 x 1 - 1 / 2 " NOTE : " i _ is engine could have been bui6 with 590702 35 35395 Reslator Spark Plug ( FU19LM ) starter ) . NOTE : All component dimensions given in U . S . Inches 1 inch = 25.4 mm 43
Page: 26

CRAFTSM4A - NCYCUEENGINE MODEL NO . 143.996510 44
Page: 27

CRAFTSMAN 4 - CYCLE ENGINE MODEL NO . 143.996510 KEY PART NO . NO . DESCRIPTION - - 640174 Carburetor ( Ir _ , l . 184 of Engine Perts LiStI 1 631615 Thtot6e Shaft & Lever Assembly 2 631767 Throttle Return Spdng 4 631184 " Dust Seal Washer 5 631183 " Dust SeaJ ( Throttle ) 6 640070 Throltle Shutter 7 650506 " Shutter Screw 16 631807 Fuel Flffing 17 661025 Throt _ e Crack Screw / Idle Speed Screw 18 630766 Tension Swingr 20 640016 Idk _ ResVioto Screw 20A 640053 Idle Restdctor Screw Cap 25 631867 Fleat Sowl 27 631024 ° Float Shaft 28 63201 g Float 29 631028 * Float Bowl = O ' Ring 30 631021 " Inlet Needle , Seat , & Clip ( Incl . 31 ) 31 631022 Spdng Cl _ p 35 36045A Pdmer Bulb / Releiner Ring 36 640080 Main Nozzle Tube 36A 632766 CeYouretor Tube 37 632547 • " O " Ring , Main Nozzle Tube 40 640175 High Speed Bowl Nut 44 27110A Bowl Nut Washer 47 630748 * Welch Plug , Idle Mixture Well 48 631027 " Welch Plug , Atmosphadc Vent 48A 631027 * Welch Plug 60 632760 Repair kit ( incl . Items Marked " ) 45
Page: 28

CRAFTSMAN 4 - CYCLE ENGINE MODEL NO . 143.996510 O . 143.996510 u 11 r3 KEY PART NO . NO . DESCRIPTION - - - - 590702 Recoil Starter 1 590599A Spring Pin ( Incl . 4 ) 2 590600 Washer 3 590696 Retainer 4 590601 Washer 5 590697 Brake Spring 6 590698 Starter Dog 7 590699 Dog Spring 8 590700 Pulley & Rewind Spring Ass'y . 11 590703 Starter Housing Ass'y . ( 40 degree grommet ) 12 590535 Starter Rope ( 98 " X 9 / 64 " dia . ) 13 590701 Starter Handle 46
Page: 29

CRAFTSMAN 4 - CYCLE ENGINE MODEL NO . 143.996510 _ 14 12 / 13 _ a III 11 _ 7 KEY PART NO . NO . DESCRIPTION - - 590739 RewindStarter 3 - 590740 Retainer 6 590616 Starter Dog 7 590617 Dog SpdngRewind 8 590618A Pulley & SpringAss'y 11 590638 Starter HousingAss'y ( 40 degree grommet ) 12 590535 Starter Rope ( Length 98 " x 9 / 64 " dia . ) 13 590701 Starter Handle 14 590760 SpringClip 47
Page: 30

Forthe repair or replacement parts you need delivered directly to your home Call 7 am - 7 pro , 7 days a week 1 - 800 - 366 - PART ( 1 - 800 - 366 - 7278 ) Para ordenar piezas con entrega a domicilio - 1 - 800 - 659 - 7084 For in - house major brand repair service Call 24 hours a day , 7 days a week 1 - 800 - 4 - REPAIR ( 1 - 800 - 473 - 7274 ) Para pedir servicio de reparaci6n a domicilio - 1 - 800 - 676 - 5811 For the location of a Sears Parts and Repair Center in your area Call 24 hours a day , 7 days a week 1 - 800 - 488 - 1222 For information on purchasing a Sears Maintenance Agreement or to inquire about an existing Agreement Call 9 am - 5 pm , Monday - Saturday 1 - 800 - 827 - 6655 When requesting service or ordering parts , always provide the following information : • Product Type • Part Number • Model Number • Part Description SKARS America's Repair Specialists 166080 10.14.98 VB / SV Printedin U . S . A .
Search in Walk-Behind-Mowers on ebay
"
* Clicking the part number will send you to Sears Parts Direct.
033623 Gas can (2.5 gal.)
033500 Fuel stabilizer
033303 Clipping deflector
033300 Sae 30w oil (20 oz.)
0166080 Owner's manual (english/ spanish)
0161058 Warning decal
033723 High wheel kit
033417 Dust shield
033316 Mower cover
1165451X479 Upper handle
10128415 Blind rivet
11150050 Hxtap screw
12STD512505 Hex tapping screw w/sems 1/4-20 x 1/2
1377400 Hub cap
14156374X479 Back Plate
15700365X479 Side baffle
16133190X479 Baffle
17140661X479 Rear baffle
1863601 Keps locknut 1/4-20
2156577 Engine zone control cable
20140540 Rear skirt
2285543 Engine pulley
2387677 High - pro key
2583923 Lock nut
27151158 Rear Wheel
28142748 Bolt
2962335 Washer
30145935X004 Axle arm
31701037 Knob, selector, spring
32700331X004 Spring
34146630 Height spacer
35700325X007 Bracket
37150078 Thread cutting screw with sems 5/16-18 x 3/4
39151512X479 Handle bracket
4150425 Mulcher plug
40151511X479 Handle bracket
41150406 Screw, hex head, threaded, rolled 3/8-16 x 1 - 1/8
44161769 Lawn mower housing (incl. key #14,15,51)
46851514 Blade adapter
47157101 Blade 22"
48851074 Washer
49850263 Lock washer
566426 Wire tie
50851084 Screw
51165548 Front baffle
5285463 Decal
55751592 Locknut 3/8-16
5688652 Hinge screw
5751793 Hairpin
58157081X479 Handle
59131959 Handle bolt
6136376 Handle knob
61132001 Rope guide
62134612 Debris shield
64N/P Engine tecumseh model no. 143.996510
8145793 Control bar
9151023 Rear Rear door assembly kit
1145755 Control cable assembly
11151156 Wheel and tire assembly
1212000058 External e-ring
13137054 Pinion
1488080 Cover, duct wheel
1588118 Washer
1667725 Washer
18701037 Knob, selector, spring
26143603 Pan head tapping screw no. 10-24 x 2-3/4
28154990 Drive cover
3751152 Locknut #10-24
31132010 Hex flange nut
32137052 Drive pulley
35151521 Adjuster
36702511 Gear case assembly
37137090 Spring
3863601 Nut
4158755 Screw, machine, pan head 1/4-20 x 2-3/16
4075192 Spring
41151520 Kit, wheel adjuster, rh (includes knob and bear...
5146527 V-belt
53144747 Frame
54166069 Grass bag
5586012 Driveshaft cover
57144748 Frame
6150495 Spring . retainer
877400 Hub cap
9145212 Hex nut