Home | Register Login | Wanted Manuals | MarketPlace | Members Area | Manuals Manufacturer Directory | UPC Lookup | Information Pages | Policy


Back To Craftsman Walk-Behind-Mowers       Model: 917.377582 or 917377582 Craftsman 6.75 HP 22 Inch Rear Discharge Lawn Mower
Regular Text Search or Search by Model Number

Register / log-in to add to your Hammerwall Collection.
Manual Location


This is a partial text extraction from the pdf, to download the pdf, click the Manual tab. If you want to search this text, hold control and F, and type the word you are looking for.

Page: 1

Owner's Manual £ RRFTSMRN ° 6.75 HORSEPOWER 22 " REAR DISCHARGE POWER PROPELLED ROTARY LAWN MOWER Model No . 917.377582 • Safety • Assembly • Operation • Maintenance • Espa _ ol • Repair Parts CAUTION : Read and follow all Safety Rules and Instructions before operating this equipment Sears , Roebuck and Co . , Hoffman Estates , IL 60179
Page: 2

Warranty 2 Product Specifications 11 SafetyRules 2 Service and Adjustments 14 Assembly 4 Storage 16 Operation 6 Troubleshooting 17 Maintenance Schedule 10 Repair Parts 37 Maintenance 10 Parts Ordering Back Cover I LIMITED TWO YEAR WARRANTY ON CRAFTSMAN POWER MOWER For two years from dat e of 15umhase , when this Craftsman Lawn Mower is maintained , lubricated , and tuned up acCording to the operating and maintenance instructions in the owner's manual , Searsiwill _ ' epa r free of charge any defect n mater a or workmanship If th = sCraftsman Lawn Mower is used for commerc = al or rental purposes , this warranty applies for only 90 days fro _ the date of purchase . This Warranty does not cover : • Expendable items which become worn during normal use , such as rotary mower blades , blade adapters , I _ elts , a = rcleaners and spark plug . • Repairs necessary b , bca _ se of operator abuse or negligence , including bent crank - shafts and the failure to maintain the equipment according to the instructions con - tained in the owner's manual . . Warranty service is available byr _ tuming the Craftsman power mower to the nearest Sears Service Center / Department in the United States . This warranty applies only while this product is in use in the United States . This Warranty gives you spec fic ega rights , and you may also have other rights which vary from state to state . SEARS , ROEBUCK AND CO . , D / 817 WA , HOFFMAN ESTATES , ILLINOIS 60179 Safety standards require operator pres - • Do not operate mower if it has been ence controls to minimize the risk of injury . dropped or damaged in any manner . Your unit is equipped with such controls . Always have damage repaired before Do not attempt to defeat the function of the using your mower . controls under any circumstances • • Do not use accessory attachments that TRAINING : are not recommended by the manufac - turer . Use of such attachments may be • Read this operator's manual carefully . hazardous . Become familiar with the controls and • The blade tums when the engine is know how to operate your mower running . properly . Learn how to quickly stop mower . PREPARATION : • Do not allow children to use your mower . • Always thoroughly check the area to be Never allow adults to use mower without mowed and clear it of all stones , sticks , proper instructions . wires , bones , and other foreign objects . • Keep the area of operation clear of all These objects will be thrown by the blade persons , especially small children and and can cause severe injury . pets . • Always wear safety glasses or eye • Use mower only as the manufacturer shields when starting and while using intended and as described in this manual . your mower . 2
Page: 3

fu _ ara dan _ raus . • Dressproperly . Donotoperatemower • Never cut grass by pulling the mower whenbarefootorwearingopensandals . towards you . Mow across the face of Wearonlysolidshoeswithgoodtraction when mowing . slopes , never up and down or you might • Check fuel tank before starting engine . lose your footing . Do not mow exces - sively steep slopes . Use caution when Do not fill gas tank indoors , when the operating the mower on uneven terrain engine is running or when the engine is hot . Allow the engine to cool for several or when changing directions - - maintain minutes before filling the gas tank . Clean good footing . • Never operate your mower without off any spilled gasoline before starting the engine . proper guards , plates , grass catcher or other safety devices in place . • Always make wheel height adjustments before starting your mower . Never MAINTENANCE AND STORAGE : attempt to do this while the engine is • Check the blade and the engine mount - running . ing bolts often to be sure they are • Mow only in daylight or good artificial tightened properly . light . • Check all bolts , nuts and screws at OPERATION : frequent intervals for proper tightness to be sure mower is in safe working • Keep your eyes and mind on your mower condition . and the area being cut . Do not let other interests distract you . • Keep all safety devices in place and • Do not mow wet or slippery grass . Never working . • To reduce fire hazard , keep the engine run while operating your mower . Always be sure of your footing - - keep a firm free of grass , leaves or excessive grease hold on the handles and walk . and oil . • Do not put hands or feet near or under • Check grass catcher often for deteriora - rotating parts . Keep clear of the discharge tion and wear and replace worn bags . opening at all times . Use only replacement begs that are recommended by and comply with • Always stop the engine whenever you spec'ifications of the manufacturer of your leave or are not using your mower , or mower . before crossing driveways , walks , roads , • Always keep a sharp blade on your and any gravel _ covered areas . mower . • Never direct discharge of material toward bystanders nor allow . anyone near the • Allow engine to cool before storing in any enclosure . mower while you are operating it . • Never store mower with fuel in the tank • Before cleaning , inspecting , or repairing your mower , stop the engine and make inside a building where fumes may reach an open flame or an ignition source such absolutely sure the blade and all moving as a hot water heater , space heater , parts have stopped . Then disconnect the spark plug wire and keep it away from the clothes dryer , etc . ACAUTION : Always disconnect spark spark plug to prevent accidental starting . plug wire and place wire where it cannot • Do not continue to run your mower if you contact spark plug in order to prevent hit a foreign object . FolLow the procedure accidental starting when setting up , outlined above , then repair any damage transporting , adjusting or making repairs . before restarting and operating you WARNING mower . The engine exhaust from this product • Do not change the governor settings or contains chemicals known to the State of overspeed the engine . Engine damage or California to cause cancer , birth defects , or personal injury may result . • Do not operate your mower if it vibrates other reproductive harm . abnormally . Excessive vibration is an indication of damage ; stop the engine , safely check for the cause of vibration and repair as required . • Do not run the engine indoors . Exhaust 3
Page: 4

Theseaccessoriewsereavailablewhenthislawnmowerwasproduced . They are also avaH _ d : ) io at most Sears retail outlets and service centers . Most Sears stores can also order i _ ir parts for you , when you provide the model number of your lawn mower . Some of these accessories may not apply to your lawn mower . LAWN MOWER PERFORMANCE FL CLIPPING DEFLECTOR FOR REAR DISCHARGE LAWN MOWERS MULCHER KITS STABILIZER GRASS CATCHERS FOR FOR REAR DISCHARGE GRASS SECATCHERS LAWN MOWERS J SIDE RDISCHARG LAWN MOWE GAS CANS LAWN MOWER MAINTENANCE MUFFLERS AIR FILTERS SPARK PLUGS BELTS BLADES BLADE ADAPTERS WHEELS ENGINE OIL Read these instructions and this manual in TO REMOVE LAWN MOWER FROM its entirety before you attempt to assemble CARTON or operate your new lawn mower . Your new • Remove loose parts included with lawn mower has been assembled at the mower . factory with the exception of those parts left • Cut down two end corners of carton and unassembled for shipping purposes . All lay end panel down flat . parts such as nuts , washers , bolts , etc . , • Remove all packing materials except necessary to complete the assembly have padding between upper and lower been placed in the pads bag . To ensure handle and padding holding operator safe and proper operation of your lawn presence control bar to upper handle . mower , all parts and hardware you as - • Roll lawn mower out of carton and check semble must be tightened securely . Use the carton thoroughly for additional loose correct tools as necessary to ensure proper pads . tightness . 4
Page: 5

HOW TO SET UP YOUR LAWN TO INSTALL ATTACHMENTS MOWER Your lawn mower was shipped ready to be TO UNFOLD HANDLE used as a mulcher . To convert to bagging or discharging : IMPORTANT : Unfold handles carefully so • Open rear door and remove mulcher as not to pinch or damage control cables . plug . Store mulcher plug in a safe place . • Raise handles until lower handle section • You can now install catcher or optional locks into place in mowing position . clipping deflector . • Remove protective padding , raise upper • To retum to mulching operation , install handle section into place on lower mulcher plug into discharge opening of handles and tighten both handle knobs . • Remove handle padding holding operator presence control bar to upper handle . mower . • Your lawn mower handle can be adjusted for your mowing comfort . Refer Mulcher plug _ to " Adjust Handle " in the Service and Adjustment section of this manual . ACAUTION : Do not mn your lawn mower Operator presence without mulcher plug in place or approved control bar clipping deflector or grass catcher in place . up Never attempt to operate the lawn mower with the rear door removed or propped Uft up open . Mowing position Lower handle 5
Page: 6

KNOW YOUR LAWN MOWER READTHIS OWNER " SMANUALAND SAFETY RULES BEFORE OPERATING YOUR LAWN MOWER . Comparethe illustrationws ithyourlawnmowerto familiarize yourselfwiththe location of variouscontrolsand adjustments . Save thismanualforfuture reference . These symbols may appear on your lawn mower or in literature supplied with the product . Learn and understand their meaning . CAUTION ENGINE ENGINE FAST SLOW CHOKE FUEL OIL DANGER , KEEP HANDS OR WARNING ON OFF AND FEET AWAY Operator presence control bar \ Drive controllever Starter handle Engine oil cap withdipstick Drive cover Mulcher plug Gasoline filler cap Lawn mower housing Primer Wheel adjuster ( on each wheel ) MEETS CPSC SAFETY REQUIREMENTS Sears rotary walk - behind power lawn mowers conform to the safety standards of the American National Standards Instituteand the U . S . Consumer Product Safety Commission . The blade lures when the enR " i , he is running . Operator Presence Control Bar - must be Drive Control Lever - - usedtoengage power - propellefdorwardmotionof lawn held down to the handle to start the engine . mower . Release to stop the engine . Mulcher Plug - locatedatthedischarge Palmer - pumps additional fuel from the opening must be removed when convert - carburetor to the cylinder for use when starting ingtobagging ordischargingoperation . a cold engine . Starter Handle - used for starting the engine .
Page: 7

TO A'rrACH GRASS CATCHER The operationofany lawn mower can reeultin foreign objectsthrownintothe eyes , whichcan • cleee itip FRp be resultinsevereeye damage . Alwayswear while operating lawn mower . safetyglassesoreye shieldswhileoperating • Liftthe rear door on the mower housing and yourlawnmoweror performingany adjust - place the grass catcher frame onto the mentsor _ alm . We recommenda wide formed tabs on the rear door hinge bracket . visionsafety mask overspectaclesor standard • The grass catcher is secured to the lawn safety glasses . mower housing when the rear door is HOW TO USE YOUR LAWN MOWER lowered onto the grass catcher frame . ENGINE SPEED CONTROL & CAUTION : Do not run your lawn mower without clipping deflector or approved The engine speed was set at the factory grass catcher in place . Never attempt to for optimum performance . Speed is not operate the lawn mower with the rear door adjustable . removed or propped open . ENGINE ZONE CONTROL ACAUTION : Federal regulations require an engine control to be installed on this Hinge door lawn mower in order to minimize the risk of bracket Grass catcher blade contact injury . Do not under any circumstances attempt to defeat the function of the operator control . The blade Formed turns when the engine is running . tabs • Your lawnmoweris equippedwithan operatorpresencecontrolbar which requiresthe operatorto be behindthe lawn mowerhandleto stad and operatethe lawnmower . TO EMPTY GRASS CATCHER TO ADJUST CUTnNG HEIGHT • To removegrasscatcher , reteaseoperator • Raise wheels for low cut and lower wheels presencecontrolbarto stopengine . for high cut . • Liftup reardoorand removethe grass • Adjust cutting height to suit your require - catcherbythehandle . ments . Medium position is best for most lawns . NOTE : Do notdragthe bag when emptying ; itwillcause unnecessarywear . • To change cutting height , squeeze adjuster lever toward wheel . Move wheel up or down to suit your requirements . Be sure all wheels are in the same satUng . NOTE : Adjuster is properly pesitk ) ned when plate tab inserts into hole in lever . Also , 9 - position adjusters ( if so equipped ) allow lever to be positioned between the plate tabs . Lower Wheels for High Cut Raise Wheels _ P _ for LowCut _ _ Lever
Page: 8

GAS ) RIVE CONTROL Self - propelling is controllid by holding the • Fillfuel tank . Use fresh , clean , regular operator presence control bar down to the unleaded gasoline with a minimum of 87 handle and pushing the drive control liver octane . Do not mix oil with gasoline . forward until it clicks ; then release the liver . Purchase fuel in quantities that can be used Forward motion will stop when the operator within 30 days to assure fuel freshness . presence control bar is released . To stop WARNING : Experience indicates that forward motion without stopping engine , alcohol blended fuels ( called gasohol or release the operator presence control bar using ethanol or methanol ) can attract slightly untilthe drive control disengages . moisture which leads to separation and Hold operator presence control bar down to formation of acids during storage . Acidic handle to continue mowing without self - gas can damage the fuel system of an propelling . engine while in storage . To avoid engine . To keep drive control engaged when turning problems , the fuel system should be comers , push down on handle and lift front emptied before storage of 30 days or wheels oft ground while tuming lawn longer . Drain the fuel tank , start the engine mower . and let it run until fuel lines and carburetor are empty . Use fresh fuel next season . ) perator presence Drive See Storage Instructions for additional control bar _ \ _ _ - - " ontrol information . Never use engine or carbure - tor cleaner products in fuel tank or permanent damage may occur . \ _ \ _ , Drive control Engine oil cap TOengage x , \ x _ i _ . . . . . . , _ dl _ l lyctyt _ u drive control fillercap 3EFORE STARTING ENGINE OIL Gasoline _ _ ' our lawn mower is shipped without oil in the = . ngine . TO START ENGINE , Be sure mower is level and area around oil flUis clean . • To start a cold engine , push primer five ( 5 ) times before trying to starL Use a firm push . , Remove engine oil cap and fill to the full line on the dipstick . This step is not usually necessary when , Use 27 ozs . of oil . For type and grade of oil starting an engine which has already run for a few minutes . to use , see " ENGINE " in Maintenance section of this manual . • Hold operator presence control bar down to the handle and pullstarter handle quickly . , Pour oil slowly . Do not over fill . • Check oil level before each use . Add oil if Do not allow starter rope to snap back . needed . Fillto full line on dil _ tick . • To stop engine , release operator presence control bar . • To read proper level , tighten engine oil cap each { ime . NOTE : In cooler weather it may be necessary • Reinstall engine oil cap and tighten . to repeat priming steps . In warmer weether • Change the oil after every 25 hours of over priming may cause flooding and engine will not start . If you do flood engine , wait a few operation or each season . You may need minutes before attempting to start and do not to change the oil more often under dusty , repeat priming steps . dirtyconditions .
Page: 9

MOWING TIPS MULCHING MOWING TIPS • Under certain conditions , such as very IMPORTANT : For best performance , keep tall grass , it may be necessary to raise mower housing free of built - up grass and the height of cut to reduce pushing effort trash . Clean UNDERSIDE OF MOWER and to keep from overloading the engine HOUSING after each use . See " Cleaning " in MAINTENANCE section of this manual . and leaving clumps of grass clippings . It may also be necessary to reduce • The special mulching blade will recut the ground speed and / or run the lawn grass clippings many times and reduce mower over the area a second time . them in size so that as they fall onto the • For extremely heavy cutting , reduce the lawn they will disperse into the grass and width of cut by overlapping previously not be noticed . Also , the mulched grass will cut path and mow slowly . biodegrade quickly to provide nutrients for • For better grass bagging and most the lawn . Always mulch with your highest cutting conditions , the engine speed engine ( blade ) speed as this will provide the should be set in the fast position . best recutting action of the blades . • When using a rear discharge lawn • Avoid cutting your lawn when it is wet . Wet mower in moist , heavy grass , clumps of grass tends to form dumps and interferes cut grass may not enter the grass with the mulching action . The best time to catcher . Reduce ground speed ( push - mow your lawn is the early aftemoon . At this ing speed ) and / or run the lawn mower time the grass has dried and the newly cut over the area a second time . area will not be exposed to the direct sun . • If a trail of clippings is left on the right • For best results , adjust the lawn mower side of a rear discharge mower , mow in cutting height so that the lawn mower cuts a clockwise direction with a small off only the top one - third of the grass blades . overlap to collect the clippings on the If the lawn is overgrown it will be necessary next pass . to raise the height of cut to reduce pushing • Pores in cloth grass catchers can effort and to keep from overloading the become filled with dirt and dust with use engine and leaving clumps of mulched and catchers will collect less grass . To grass . For extremely heavy mulching , prevent this , regularly hose catcher off reduce your width of cut , mow slowly and with water and let dry before using . raise the rear of the lawn mower one wheel • Keep top of engine around starter clear adjuster setting higher than the front . and clean of grass clippings and chaff . • Certain types of grass and grass conditions This will help engine air flow and extend may require that an area be mulched a engine life . second time to completely hide the clippings . When doing a second cut , mow across or perpendicular to the firstcut path . • Change your cutting pettem from week to week . Mow north to south one week then change to east to west the next week . This will help prevent matting and graining of the lawn . 9
Page: 10

. A , ENANSCCENEOULE FILL IN DATES _ _ _ _ _ REGULAR SERVICE Check for Loose Fasteners ( p / ti / Clean / Inspect Grass Catcher M Clean Lawn Mower ( Power - Propelled Mowers ) II / O Clean Under Drive Cover Check ddve belt / pulleys E Power . Propelled Mowers ) b / CheckJSharpeNReplace Blade I , / 3 Lubrication Chart ll / II _ Clean BatteP / / Recha = rge v ' v ' , Electric Start MowersI i E _ heck EnQine Oil Level qp / N Change Ermine Oil 11 _ 1.2 G CleanAirFilter _ 2 I Inspect Muffler N CleanorReplaceSparkPlug E Replace Air Filter Paper Cartridge I _ 2 I - Change more onen when operating under a heavy k _ ad or in h _ gh ambient temperatures . 2 - Service moro often when operating In dldy or du _ y conditions . 3 . Repine blades nm ( e often when mowing kl sandy soil . 4 - Charge 48 hours at end of mso _ . LUBRICATION CHART GENERAL RECOMMENDATIONS ( _ ) Wheel The warranty on this lawn mower does not adjusters _ cover items that have been subjected to operator abuse or negligence . To receive full I value from the warranty , operator must maintain mower as instructed in this manual . Some adjustments will need to be made periodically to properly maintain your unit . All adjustments in the Service and ( _ ) Engine oil Adjustments section of this manual should be checked at least once each season . • Once a year , replace the spark plug , replace air filter element and check blade for wea _ . A new spark plug and clean / new air filter element assures proper air - fuel mixture and ( _ ) rRear ( _ ) Handle bracket doo helps your engine run better and last longer . mounting pin • Follow the maintenance schedule in this hinge manual . ( D SPRAYLUBRICANT BEFORE EACH USE ( _ SAE 30 MOTOR OIL . REFER TO • Check engine oil leveL ENGINE - MAINTENANCE SECTION . • Check for loose fasteners . LUBRICATION IMPORTANT : Do not oil or grease plastic Keep unit well lubricated ( See " LUBRICATION wheel bearings . Viscous lubricants will attract dust and dirt that will shorten the life of the self CHART " ) . lubricatingbearings . If you feel they must be lubricated , use only a dry , powdered graphite type lubricantsparingly . 10
Page: 11

PRODUCT SPECIFICATIONS MODEL NUMBER 917.377582 SERIAL NUMBER DATE OF PURCHASE HORSEPOWER : 6.75 DISPLACEMENT : 12.56 CU . IN . _ ASOLINE CAPACITY / TYPE : 1.5 QUARTS UNLEADED REGULAR OIL TYPE ( API - SF / SG / SH ) : SAE 30 ( ABOVE 32 ° F ) SAE 5W - 30 ( BELOW 32 ° F ) OIL CAPACITY : 27 OZS . SPARK PLUG ( GAP : . 030 " ) CHAMPION RJ19LM OR J19LM VALVE CLEARANCE : INTAKE : . 004 - . 008 EXHAUST : . 004 - . 008 SOLID STATE IGNITION AIR GAP : . 0125 IN . BLADE BOLT TORQUE : 35 - 40 FT . LBS . The model and serial numbers will be found on a decal attached to the rear of the lawn mower housing . Record both serial number and date of purchase in space provided above . LAWN MOWER • Remove blade and attaching hardware Always observe safety rules when performing ( bolt , lock washer and hardened any maintenance . washer ) . NOTE : Remove the blade adapter and TIRES check the key inside hub of blade • Keep tires free of gasoline , oil , or insect adapter . The key must be in good control chemicals which can harm rubber . condition to work properly . Replace • Avoid stumps , stones , deep ruts , sharp adapter if damaged . objects and other hazards that may cause TO REPLACE BLADE tim damage . • Position the blade adapter on the BLADE CARE engine crankshaft . Be sure key in For best results , mower blade must be kept adapter and crankshaft keyway are sharp . Replace bent or damaged blades . aligned . TO REMOVE BLADE • Position blade on the blade adapter aligning the two ( 2 ) holes in the blade • Disconnect spark plug wire from spark with the raised lugs on the adapter . plug and place wire where it cannot • Be sure the trailing edge of blade come in contact with spark plug . • Turn lawn mower on its side . Make sure ( opposite sharp edge ) is up toward the engine . air filter and carburetor are up . • Install the blade bolt with the lock • Use a wood block between blade and washer and hardened washer into mower housing to prevent blade from blade adapter and crankshaft . turning when removing blade bolt . • Use block of wood between blade and • Protect your hands with gloves and / or lawn mower housing - and tighten the wrap blade with heavy cloth . blade bolt , turning clockwise . • Remove blade bolt by turning counter - clockwise . • The recommended tightening torque is 11 35 - 40 ft . Ibs .
Page: 12

MPORTANT : Bladeboltis grade8 heat If necessary to clean the drive wheels , check both front wheels . teated . • Remove hubcaps , hairpin cotters and ro SHARPEN BLADE washers . _ IOTE : We do not recommend sharpening • Remove wheels from wheel adjusters . ) lade - but if you do , be sure the blade is • Remove any trash or grass cuttings from _ alanced . inside the dust cover , pinion and / or drive 3are should be taken to keep the blade wheel gear teeth . _ alanced . An unbalanced blade will cause • Put wheels back in place . = . ventual damage to lawn mower or • If after cleaning , the drive wheels do not . = ngine . turn freely , contact your nearest , The blade can be sharpened with a file authorized service center . or on a grinding wheel . Do not attempt GEAR CASE to sharpen while on the mower . • To keep your drive system working , To check blade balance , drive a nail into properly , the gear case and area around a beam or wall . Leave about one inch the drive should be kept clean and free of the straight nail exposed . Place of trash build - - up . Clean under the drive center hole of blade over the head of the cover twice a season . nail . If blade is balanced , it should • The gear case is filled with lubricant to remain in a horizontal position . If either the proper level at the factory . The only end of the blade moves downward , time the lubricant needs attention is if sharpen the heavy end until the blade is service has been performed on the gear balanced . case . Blade Crank shaft • If lubricant is required , use only Texaco adapter Starplex Premium 1 Grease , Part No . 750369 . Do not substitute . ENGINE LUBRICATION Use only high quality detergent oil rated with API service classification SF , SH or Bolt Crank SG . Select the oirs SAE viscosity grade Lockwasher Hardened Blade shaft according to your expected operating washer Trailing adapter temperature . edge SAE VISCOSrrY GRADES GRASS CATCHER • The grass catcher may be hosed with water , but must be dry when used . • Check your grass catcher often for damage or deterioration . Through normal use it will NOTE : Although multi - - viscosity oils wear . If catcher needs replacing , replace ( 5W30 , 10W30 etc . ) improve starting in only with a manufacturer _ approved cold weather , these multi - - - viscosity oils replacement catcher . Give the lawn mower will result in increased oil consumption model number when ordering . when used above 32 ° F . Check your engine oil level more frequently to avoid DRIVE WHEELS possible engine damage from running low Check front drive wheels each time before on oil . you mow to be sure they move freely . Change the oil after every 25 hours of opera - The wheels not turning freely means trash , grass cuttings , etc . are in the drive wheel tion or at least once a year if the lawn mower area and must be cleaned to free drive is not used for 25 hours in one year . wheels . Check the crankcase oil level before starting the engine and after each five ( 5 ) hours of continuous use . Tighten oil plug securely each time you check the oil level . 12
Page: 13

MUFFLER TO CHANGE ENGINE OIL Inspect and replace corroded muffler as it NOTE : Before tipping lawn mower to drain could create a fire hazard and / or damage . oil , drain fuel tank by running engine until SPARK PLUG fuel tank is empty . Change your spark plug each year to make • Disconnect spark plug wire from spark your engine start easier and run better . Set plug and place wire where it cannot spark plug gap at . 030 inch . come in contact with spark plug . • Remove engine oil cap ; lay aside on a CLEANING clean surface . IMPORTANT : For best performance , keep • Tip lawn mower on its side and drain oil mower housing free of built - - up grass and into a suitable container . Rock lawn trash . Clean underside of mower housing after mower back and forth to remove any oil each use . trapped inside of engine . , & CAUTION : Disconnect spark plug wire • Wipe off any spilled oil on lawn mower from spark plug and place wire where it cannot and on side of engine . come in contact with the spark plug . • Fill engine with oil . Fill only to the = FULL " • Turn lawn mower on its side . Make sure air line on the dipstick . DO NOT OVER FILL . filter and carburetor are up . Clean the • Replace engine oil cap . underside of your lawn mower by scraping • Reconnect spark plug wire to spark to remove bu = 1d _ up of grass and trash . plug . • Clean engine often to keep trash from accumulating . A dogged engine runs hotter and shortens engine life . Container • Keep finished surfaces and wheels free of all gasoline , oil , etc . • We DO NOT recommend using a garden hose to clean lawn mower unless the AIR FILTER electricalsystem , muffler , air filter and Your engine will not runproperly and may be carburetor are covered to keep water out . damaged by using a dirty air filter . Water in engine can result in shortened engine life . Replace the air filter every year , more often ifyou mow invery dusty , dirtyconditions . Do CLEAN UNDER DRIVE COVER not wash air filter . Clean under drive cover at least twice a TO CHANGE AIR FILTER season . Scrape underside of cover with putty • Loosen cover knob knife or similar tool to remove any build - - up of • Swing cover down and remove from hinge trash or grass on underside of drive cover . • Pull paper filter out of air cleaner body • Clean aircleanercoverand body . • Install a new peper filter . • Reinstall cover to air cleaner body . Be sure hinge is assembled properly . • Swing cover up and tighten cover knob . ( Do not overtighten ) . Air filtercover Hinge Cover Paper filter knob 13
Page: 14

• Remove the cable clips . ` & CAUTION : Before performing any • Remove the controls and operator service or adjustments : presence control bar from the upper • Release control bar and stop engine . handle . • Make sure the blade and all moving • Remove starter rope guide from upper parts have completely stopped . handle . • Disconnect spark plug wire from • Remove hairpin cotters . spark plug and place where it cannot • Disconnect the lower handle from the come in contact with plug . handle brackets . LAWN MOWER • Turn the handle over and reassemble TO ADJUST cu'n'ING HEIGHT the hairpin cotters that have been See " TO ADJUST CUTTING HEIGHT " in removed . the Operation section of this manual . • Reassemble the starter rope guide . REAR DEFLECTOR • Reassemble the controls and the The rear deflector , attached between the operator presence control bar to the rear wheels of your lawn mower , is upper handle . provided to minimize the possibility that , & CAUTION : The operator presence objects will be thrown out the rear of the control bar must pivot freely to permit lawn mower into the operator's mowing blade brake engagement when control bar position . is released . Do not over tighten the If the rear deflector becomes damaged , it fasteners holding the controls to the upper should be replaced . handle . TO REMOVE / REPLACE DRIVE BELT • To change from medium low to high position only the upper handle section • Remove drive cover . Remove belt by will have to be turned over . pushing down on gear case pulley and • To change from medium low to low rolling belt off it . • Turn lawn mower on its side with position , only the lower handle section will have to be turned over . carburetor and fuel cap up . • Remove blade . Shipping Position • Remove debris shield . Medium Low • Remove belt from engine pulley on crankshaft . • Install new belt by reversing above steps . • Always use factory approved belt to Medium High assure fit and long life . \ Drive - . _ . . . J _ L _ k _ U _ / cover _ _ n1 - _ Low own lgll TO ADJUST HANDLE High Your lawn mower handle can be raised or lowered for your mowing comfort . Four ( 4 ) positions are available : high , medium high , medium low and low . Handles are shipped mounted in the medium low position . • To change from medium low to medium high position , the upper and lower handle sections will have to be turned over . 14
Page: 15

Lower Handle Lower frame Squeezeto \ _ " F _ Frames mustbe _ - - _ . _ I fully seated ) \ Handle remove _ Bracket Tubular frame Hairpin Cotter Lower frame handle TO ASSEMBLE GRASS CATCHER • Insert leg of tubular frame through front opening of grass catcher and thread frame into sewn hem of bag . NOTE : Keep bag hem gathered on the straight leg of the tubular frame . • When frame comes out the other end of sewn hem , immediately work the end of frame down inside the bag as shown in inset . • Slide sewn hem evenly around the ENGINE tubular frame until both ends of frame CARBURETOR are exposed out of the front opening . • Assemble lower frame to tubular frame Your carburetor has a non - adjustable fixed as shown . Be sure handle is outside of main jet for mixture control . If your engine bag and frames are fully seated as does not operate properly due to sus - shown in inset . pected carburetor problems , take your • Slip vinyl bindings over frame . lawn mower to an authorized service NOTE : if vinyl bindings are too stiff , hold center for repair or adjustment . them in warm water for a few minutes . If ENGINE SPEED bag gets wet , let it dry before using . Your engine speed has been factory set . • Close the flip lid . Flip lid must be closed Do not attempt to increase engine speed while operating lawn mower . or it may result in personal injury . If you • , CAUTION : Do not run your lawn mower believe that the engine is running too fast without clipping deflector or approved or too slow , take your lawn mower to an grass catcher in place . Never attempt to authorized service center for repair and operate the lawn mower with the rear door adjustment . removed or propped open . Tubular fra _ _ ewn hem Se 1hem Fli _ lid 15
Page: 16

" nmediately prepare your lawn mower for ENGINE torage at the end of the season or if the unit FUEL SYSTEM , , illnot be used for30 days or more . IMPORTANT : It is important to prevent gum . AWN MOWER deposits from forming in essential fuel system Vhen lawn mower is to be stored for a period pads such as carburetor , fuel filter , fuel hose , , f time , clean it thoroughly , remove all dirt , or tank during storage . Also , experience trease , leaves , etc . Store in a clean , dry area . indicates that alcohol blended fuels ( called Clean entire lawn mower ( See " CLEANING " gasohot or using ethanol or methanol ) can in the Maintenance section of this manual ) . attract moisture which leads to separation and Lubricate as shown in the Maintenance formation of acids during storage . Acidic gas section of this manual . can damage the fuel system of an engine Be sure that all nuts , bolts , screws , and pins while in storage . are securely fastened . Inspect moving • Drain the fuel tank . pads for damage , breakage and wear . • Start the engine and let it run until the fuel Replace if necessary . lines and carburetor are empty . Touch up all rusted or chipped paint • Never use engine or carburetor cleaner surfaces ; sand lightly before painting . products in the fuel tank or permanent " IANDLE damage may occur . • Use fresh fuel next season . ( ou can fold your lawn mower handle for ; torage . NOTE : Fuel stabilizer is an acceptable Squeeze the bottom ends of the lower alternative in minimizing the formation of fuel handle toward each other until the lower gum deposits during storage . Add stabilizer to handle clears the handle bracket , then gasoline in fuel tank or storage container . move handle forward . Always follow the mix ratio found on stabilizer container . Run engine at least 10 minutes , Loosen upper handle mounting bolts after adding stabilizer to allow the stabilizer to enough to allow upper handle to be folded reach the carburetor . Do not drain the gas back . tank and carburetor if using fuel stabilizer . MPORTANT : When folding the handle for ENGINE OIL storage or transportation , be sure to fold the _ andle as shown or you may damage the Drain oil ( with engine warm ) and replace with . ' ontrol cables . clean engine oil . ( See " ENGINE " in the , When setting up your handle from the Maintenance section of this manual ) . storage position , the lower handle will CYLINDER automatically lock into the mowing position . • Remove spark plug . • Pour one ounce ( 29 ml ) of oil through spark Lower Handle plug hole into cylinder . • Pull starter handle slowly a few times to Handle Bracket distributeoil . Squeeze tofold • Replace with new spark plug . Hairpin Cotter Operator Presence Control Bar Fold Backward Mowing Position Fold FonNard For Storage Lower Handle 16
Page: 17

IMPORTANT : Never cover mower while OTHER engine and exhaust areas are stillwarm . • Do not store gasoline from one season to ACAUTION : Never storethe lawn mower another . with gasoline in the tank inside a building • Replace your gasoline can if your can starts where fumes may reach an open flame or to rust . Rust and / or dirt in your gasoline will spark . Allow the engine to cool before storing cause problems . in any enclosure . • If possible , store your unit indoors and cover it to give protection from dust and dirt . • Cover your unit with a suitable protective cover that does not retain moisture . Do not use plastic . Plastic cannot breathe which allows condensation to form and will cause your unit to rust . TROUBLE SHOOTING PROBLEM CAUSE CORRECTION Will not start • Dirty air filter . • Clean / replace air filter . • Out of fuel . • Fill fueltank . • Stale fuel . • Drain tank and refill with fresh clean fuel . • Water in fuel . • Drain fuel tank and carburetor and refill tank with fresh gasoline . • Spark plugwire is • Connect wire to plug . disconnected . • Bad spark plug . • Replace sparkplug . • Loose blade or broken • Tighten blade bolt or replace blade adapter . blade adapter . • Control bar in released • Depress control bar to handle . position • Control bar defective • Replace control bar . • Rearof lawn mower Loss of power • Set in " Higher Cut " position . housing / blade dragging in heavy grass . • Cutting too much grass . • Set in " Higher Cut " position . • Dirty air filter . • Clean / replace air filter . • Clean underside of mower • Buildup of grass , leaves and trash under mower . housing . • Check oil level . • Too much oil in engine . • Walking speed too fast . • Cut at slower walking speed . Poor cut - uneven • Worn , bent or loose blade . • Replace blade . Tighten blade bolt . • Wheelheights uneven . • Set all wheels at same height . • Clean underside of mower • Buildup of grass , leaves , and trash under mower . housing . 17
Page: 18

TROUBLESHOOTING CHART CORRECTION CAUSE PROBLEM • Replace blade . Tighten blade Excessive • Wom , bent or loose blade . bolt . vibration • Contact an authorized service • Bent engine crankshaft . center / department . • Depress control bar to upper • Engine flywheel brake is Starter rope hard on when control bar is handle before pulling starter to pull released . rope . • Contact an authodzed service • Bent engine crankshaft center / department . • Replace blade adapter . • Blade adapter broken . • Move lawn mower to cut grass • Blade dragging in grass . or to hard surface to start engine . • Drive wheels not turning • Adjust or replace ddve control i Loss of drive with drive control cable , if broken . ( Self - Propelled engaged . Mowing ) • Put belt on pulleys or replace • Belt not driving . belts if broken . • Raise cutting height . Grass catcher • Cutting height too low . • Lift on blade worn off . • Replace blade . not filling ( If so • Clean grass catcher . • Catcher not venting air . equipped ) • Raise cutting height . • Grass is too high or Hard to push wheel height is too low . • Raise rear of lawn mower • Rear of lawn mower housing one ( - ) setting higher . housing / blade dragging in grass . • Grass catcher too full . • Empty grass catcher . • Adjust handle height to suit . • Handle height position not right for you . 18
Page: 19

ROTARY LAWN MOWER - - MODEL NO . 917.377582 GEAR CASE ASSEMBLY PART NUMBER 702511 1 I KEY PART KEY PART NO . NO . DESCRIPTION NO . NO . DESCRIPTION 1 17490416 Tapping Screw 1 / 4.20 x 10 57079 Hardened Washer 1 - 1 / 4 11 131484 Clutch Yoke 2 137055X004 Engagement Bracket 12 700343 Bushing 3 137053 Shifter 13 86447 Pluglical 4 57072 Seal 14 137050 He Gear Gear Case Halves Kit 6 48373 15 750436X Clutch Jaw ( Includes Key Nos . 4 , 5 , 16 750369 Grease and 7 ) 17 12000003 E - Ring 7 77881 BeadngShaft 18 850848 Hi - Pro Key 8 137051 Worm 19 81585 ) ( 004 Spring Bracket Drive Shaft 9 137074 NOTE : All component dimensions given in U , S . inches . 1 inch = 25.4 mm 37
Page: 20

CRAFTSMAN ROTARY LAWN MOWER - - MODEL NO . 917.377582 13 27 3O 28 0o 12
Page: 21

CRAFTSMAN ROTARY LAWN MOWER - - MODEL NO . 917.377582 KEY PART KEY PART NO . NO . DESCRIPTION NO . NO . DESCRIPTION 1 165451X479 Upper Handle 39 151512X479 Handle Bracket Assembly ( Left ) 2 158152 Engine Zone Control Cable 40 151511X479 Handle Bracket Assembly ( Right ) 4 150425 Mulcher Plug 41 150406 Hex Head Thread Rolling Screw 3 / 8 - 16 x 1 - 1 / 8 5 66426 Wire'lle 44 161769 Lawn Mower Housing ( Incl . Key # 14 , 15 , 51 & 52 ) 6 136376 Handle Knob 46 851514 Blade Adapter 8 145793 Contml Bar 47 157101 Blade 22 " 9 151023 Rear Door Kit 48 851074 Hardened Washer 10 128415 Pop Rivet 49 850263 Helical Washer 3 / 8 - 24 x 1 - 3 / 8 Gr . 8 11 150050 Self Tapping Screw # 10 - 16 x 1 / 2 50 851084 Hex Head Machine Screw 3 / 8 - 24 x 1 - 3 / 8 Gr . 8 12 STD512505 Hex Tapping Screw w / Sems 1 / 4 - 20 x 112 51 165548 Kit Baffle 13 150181 Hubcap 52 85463 Danger Decal 14 156374X479 Back Plate 56 88652 Hinge Screw 1 / 4 - 20 x 1 - 1 / 4 15 700365X479 Side Baffle 57 51793 Hairpin Cottere 15 133190X479 ( D Discharge Baffle 58 157081X479 Lower Handl 17 140661X479 Rear Baffle 59 131959 Handre Bolt 18 63601 Keps Locknut 1 / 4 - 20 61 132001 Rope iGuideeld 20 140540 Rear Skirt 62 134612 Debris Sh 22 85543 Engine Pulley 64 . . . . . . Engine - Craftsman - Model No . 143,996704 23 87677 Hi - Pro Key # 505 - - 161058 Warning Decal ( Not Shown ) 25 83923 Hex Flange Nut - - 166062 Owner's Manual ( English / Spanish ) 27 150341 Wheel 28 142748 Shoulder Bolt 3 / 8 - 16 x 1 Available accessories not includedwith lawn mower : , 29 62335 Spdng Washer - - 71 33303 Clipping Deflector 30 145935X004 Axle Arm Assembly - - 71 33623 Gas Can ( 2.5 gal . ) 31 701037 SaTectorKnob - * 71 33500 Fuel Stabilizer 32 700331X004 Selector Spring - . 71 33027 SAE 30W Oil ( 27 oz , ) 34 146630 Spacer - . 71 33417 Dust Shield 35 700325X007 Wheel Adjusting Bracket ( Right ) . - 71 33316 Mower Cover 37 150078 Thread Cutting Screw w / Sems 5 / 16 - 18 x 3 / 4 . - 71 33723 High Wheel Ktt 38 751592 Nut
Page: 22

CRAFTSMAN ROTARY LAWN MOWER - - MODEL NO . 917.377582 ' 11 / . b . O 15 14
Page: 23

CRAFTSMAN ROTARY LAWN MOWER - - MODEL NO . 917.377582 KEY PART KEY PART NO . NO . DESCRIPTION NO . NO . DESCRIPTION Drive Cover 28 1549900 1 145755 Control Cable Assembly 31 13201 Hex Flange Nut 3 751152 Locknut # 10 - 24 32 137052 Drive Pulley 4 158755 Hex Washer Head Screw 1 / 4 - 20 x 2.12 35 151521 Wheel Adjuster Assembly ( Left ) 5 146527 V - Belt 36 702511 Gear Case Assembly 6 150495 Spring Retainer 37 137090 Springnut 8 150182 Hubcap 38 STD541425 Lock 1 / 4 - 20 9 145212 Locknut 40 75192 Springel 11 150340 j = . Wheel & Tire Assembly 41 151520 Whe Adjuster Assembly ( Right ) 12 12000058 E - Ring 53 144747 Frame Throat 13 137054 Pinion 54 166069 Grassbag Assembly 14 88080 Dust Cover 55 86012 Driveshaft Cover 15 88118 Felt Washer 57 144748 Frame Tube Washer 1 / 2 x 1 - 1 / 2 x . 134 16 67725 Selector Knob 18 701037 25 152903 Drive Cover Decal 26 143603 Pan Head Tapping Screw # 10 - 24 x 2 - 3 / 4
Page: 24

CRAFTSMAN 4 - CYCLE ENGINE MODEL NUMBER 143.996704 301 3OO ! 2g _ _ 310 12 24O 42 75 42
Page: 25

CRAFTSMAN 4 - CYCLE ENGII _ MODEL NUMBER 143.99670 , KEY PART KEY PART NO . NO . DESCRIPTION NO . NO . DESCRIPTION 1 36177 Cylinder ( Incl . 2,10,12,20 & 125 ) 172 32755 Valve Spring BoxCover 2 27652 Dowel Pin 174 30200 Screw , 10 - 24 x 9 / 16 " 6 36059 Breather Element 177 650925A Carburetor MountingStud 9 590568 Screw , 10 - 24 x 3 / 4 " 184 36183 Carburetor Gasket 10 36002 Governor Link BreatherValve Body 186 3600948 11 36003A Check Valve 187A 371 Air Baffle 12 32447 BreatherTube 190 36013 Brake Lever Ass'y . 12C 36005A * BreatherCover & Gasket 191A 36012 Brake ControlLever 14 28277 FlatWasher 192 36016 Brake Control Lever Link 15 36006 Governor Rod ( Machined ) 193 1360154 Brake Spdng 16 36008 GovernorLever 194 360 Retaining Ring 17 31335 GovernorLever Clamp 195 610973 Terminal Ass'y . 18 651018 Screw , Torx T - 15 , 8 - 32 x 19 / 64 " 198 36017 Brake Control Lever Spdng 19 36103 Governor Spdng 199 4360188 Brake Lever Bushingleaner 20 36010 Oil Seal 239 360 • Carburetor To Air C 25 37149 Blower Housing Baffle Gasket Ass'y . ( IncLI95 ) 240 36190 Air Cleaner Body 26 650802 Screw , 1 / 4 - 20 x 5 / 8 " ( Incl . 239 & 350 ) 30 36185 Crankshaft 243B 651041 Air Cleaner Stud 40 40004 Piston , Pin , Ring Set ( Std . ) 245 36046 Air Cleaner Filter 40005 Piston , Pin , Ring Set ( . 010 OS ) 250 36191 Air Cleaner Cover 41 36070 Piston & Pin Ass'y . ( Std . ) ( Incl . 251 650928 Lock Nut 1 / 4 - 20 43 ) 251A 650933 Wing Nut , 1 / 4 - 20 36071 Piston & Pin Ass'y . ( . 010 255 36193 Control Plate OS ) ( Incl . 43 ) 256 650983 Screw , 8 - 32 x 17 / 32 " 42 40006 Ring Set ( Std . ) 260 36188 Blower Housing 40007 Ring Set ( . 0t00S ) 261 650737 Screw , 1 / 4 - 20 x 1 / 2 " 43 20381 Piston Pin Retaining Ring 263A 36192 Starter Gdll 45 36023A Connecting Rod Ass'y . ( Incl . 46 ) 275 36107A Muffler 46 32610A Connecting Rod Bolt 276 36043 Locking Plate 48 36030 Valve Lifter 277 650927 Screw , 5 / 16 - 18 x 2 - 11 / 32 " 50 36031A Camshaft ( MCR ) 285 34449A Starter Cup 52 29914 Oil Pomp Ass'y . 287 650926 Screw , 8 - 32 x 21 / 64 " 69 36032A • MountingRange Gasket 290 29774 Fuel Line 70 37271 MountingFlange 292 26460 Fuel Line Clamp ( Incl . 72 thru 85 ) 300 4361896 Fuel Tank ( Incl . 301 ) 75 36010 Oil Seal 301 362 Fuel CapTube 80 30574A Governor Shaft 305 36063 Oil Fltl 81 30590A Washer 307 35499 " 0 " Ring 82 30591 Governor Gear Ass'y . ( IncL81 ) 308 36040 Fill Tube Clip 83 36057 Governor Spool 310 36064 Dipstick 85 36034 Idler Gear 346A 28763 Screw , 10 - 32 x 35 / 64 " 86 650924 Screw , 1 / 4 - 20 x 1 - 9 / 16 " 347 650898A Screw , 10 - 32 x 27 / 64 " 89 611154 Flywheel Key 350 36045A Primer 90 611155 Flywheel 370A 36261 LubricationDecal 91 611156 Flywheel Fan 370C 37199 Primer Decal 92 650815 BellevilleWasher 380 640020A Carburetor ( Incl . 184 & 239 ) 93 650816 Flywheel Nut 390 590739 Rewind Starter 1O0 34443B Solid State Ignition 400 36062D Gasket Set 101 61011807 Spark Plug Cover ( Incl . Items Marked • ) 103 6 - 510 Screw , Torx T - 15 , 416 36085 Spark Arrestor Kit ( Incl . 10 - 24 x 15 / 16 " 417 ) ( Optional ) 110 36054 GroundWire 417 650821 Screw , 10 - 32 x 1 / 2 " ( Optionall 119 36061 • CylinderHead Gasket 900 Replacement Engine 750819E 120 36187 CylinderHead order from 71 - 999 125 36471 ExhaustValve ( Std . ) ( Incl . 151 ) 900 Replacement Short Block 36472 ExhaustValve ( 1 / 32 " OS ) 750797B , 126 29314C Intake Valve ( Std . ) ( IncL 151 ) - - - RPM High 2900 to 3200 29315C IntakeValve ( 1 / 32 " OS ) 130 6021A Screw , 5 / 16 - 18 x 1 - 1 / 2 • NOTE : This engine could have been built wi _ 59070 135 35398 ResistorSpark Plug ( FU19LM ) starter 150 31672 Valve Spring NOTE : All componentdimensionsgiven in U . S . 151 31673 inches 1 inch = 25.4 mm LowerValve Spring Cap 151A 40016A IntakeValve Seal 169 27234A * Valve Spring BOx Gasket 43
Page: 26

CRAFTSMAN 4 - CYCLE ENGINE MODEL NUMBER 143.996704 I KEY PART NO . NO . DESCRIPTION - - - - 640020A Carburetor ( Incl . 187B & 239 of Engine Parts List ) 1 632539 Throffie Shaft & Lever Assembly Dust Seal 5 632593 Throttle Shutter 6 632541 Throttle ShutterScrew 7 650506 14A 632773 Ventad 25 632675A FloatBowl 27 632544 FloatShaft Float 28 632543 29 632548 FloatBowlto Body Gasket 30 632709 Inlet Needle & Seat 32 632672 BowlDrain Screw 33 632673 BowlDrain Washer 36 640022 Main Nozzle Tube 37 632547 " O " Ring 37A 632547 " O " Ring , Main NozzJeTube 38 632545 Spdng , Main Nozzle Tube 38A 632545 Spdngt 39 632549 Floa BowlRetainer 40 640021 Main Fuel Jet 47 632554 Welch Plug , Idle MixingWell 44
Page: 27

CRAFTSMAN 4 - CYCLE ENGINE MODEL NUMBER 143.996704 KEY PART NO . NO . DESCRIPTION 590702 RecoilStarter 1 590599A Spdng Pin ( Incl . 4 ) 2 590600 Washer 3 59O696 Retainer 4 590601 Washer 5 590697 Brake Spring 6 590698 Starter Dog 7 590699 DogSpring 8 590700 Pulley & Rewind Spring Ass'y . 11 590703 Starter HousingAss'y . ( 40 degree grommet ) 12 590535 Starter Rope ( 98 " X 9164 " dia . ) 13 590701 Starter Handle - - S Vii4 KEY PART NO . NO . DESCRIPTION 590739 Rewind Starter 3 590740 Retainer 6 590616 Starter DOg 7 590617 Dog Spring 8 590618A Pulley & Rewind SpringAss'y 11 59O638 Starter HousingAss'y ( 40 degree grommet ) 12 590535 Starter Rope ( Length 13 98 " x 9 / 64 " dia . ) 13 590701 Starter Handle 14 590760 Spring Clip 45
Page: 28

46
Page: 29

47
Page: 30

For the repair or replacement parts you need delivered directly to your home Call 7 am - 7 pro , 7 days a week 1 - 800 - 366 - PART { 1 - 800 - 366 - 7278 ) Para ordenar piezas con entrega a domicilio - 1 - 800 - 659 - 7084 For in - house major brand repair service Call 24 hours a day , 7 days a week 1 - 800 - 4 - REPAIR ( 1 - 800 - 473 - 7274 ) Para pedir servicio de reparaci6n a domtcilio - 1 - 800 - 676 - 5811 For the location of a Sears Parts and Repair Center in your area Call 24 hours a day , 7 days a week 1 - 800 - 488 - 1222 mummmm For information on purchasing a Sears Maintenance Agreement or to inquire about an existing Agreement Call 9 am - 5 pm , Monday - Saturday 1 - 800 - 827 - 6655 When requesting service or ordering parts , always provide the following information : SEARS • Product Type • Part Number • Model Number . ' Part Description America's Flepa _ r Specialists 166062 09.24.98 VB Printed in U . S . A .
Search in Walk-Behind-Mowers on ebay
"
* Clicking the part number will send you to Sears Parts Direct.
033623 Gas can (2.5 gal.)
033500 Fuel stabilizer
033303 Clipping deflector
0166062 Owner's manual (english/spanish)
0161058 Warning decal
033027 Sae 30w oil (27 oz.)
033723 High wheel kit
033417 Dust shield
033316 Mower cover
117490416 Screw
1057079 Washer
11131484 Clutch yoke
12700343 Bushing
1386447 Plug
14137050 Gear
15750436X Clutch jaw
16750369 Grease
1712000003 E-ring
18850848 High - pro key
1981585X004 Spring bracket
2137055X004 Bracket
3137053 Shifter
457072 Seal
648373 Halves kit
777881 Bearing
8137051 Shaft
9137074 Shaft
033623 Gas can (2.5 gal.)
033500 Fuel stabilizer
033303 Clipping deflector
0166062 Owner's manual (english/spanish)
0161058 Warning decal
033027 Sae 30w oil (27 oz.)
033723 High wheel kit
033417 Dust shield
033316 Mower cover
1165451X479 Upper handle
10128415 Blind rivet
11150050 Hxtap screw
12STD512505 Hex tapping screw w/sems 1/4-20 x 1/2
13150181 Hubcap
14156374X479 Back Plate
15700365X479 Side baffle
16133190X479 Baffle
17140661X479 Rear baffle
1863601 Keps locknut 1/4-20
2158152 Cable, engine zone control
20140540 Rear skirt
2285543 Engine pulley
2387677 High - pro key
2583923 Lock nut
27150341 Rear Wheel
28142748 Bolt
2962335 Washer
30145935X004 Axle arm
31701037 Knob, selector, spring
32700331X004 Spring
34146630 Height spacer
35700325X007 Bracket
37150078 Thread cutting screw with sems 5/16-18 x 3/4
38751592 Nut
39151512X479 Handle bracket
4150425 Mulcher plug
40151511X479 Handle bracket
41150406 Screw, hex head, threaded, rolled 3/8-16 x 1 - 1/8
44161769 Lawn mower housing (incl. key #14,15,51 and 52)
46851514 Blade adapter
47157101 Blade 22"
48851074 Washer
49850263 Lock washer
566426 Wire tie
50851084 Screw
51165548 Kit baffle
5285463 Decal
5688652 Hinge screw
5751793 Hairpin
58157081X479 Handle
59131959 Handle bolt
6136376 Handle knob
61132001 Rope guide
62134612 Debris shield
64N/P Engine-craftsman-model no. 143.996704
8145793 Control bar
9151023 Rear Rear door assembly kit
033623 Gas can (2.5 gal.)
033500 Fuel stabilizer
033303 Clipping deflector
0166062 Owner's manual (english/spanish)
0161058 Warning decal
033027 Sae 30w oil (27 oz.)
033723 High wheel kit
033417 Dust shield
033316 Mower cover
1145755 Control cable assembly
11150340 Drive wheel
1212000058 External e-ring
13137054 Pinion
1488080 Cover, duct wheel
1588118 Washer
1667725 Washer
18701037 Knob, selector, spring
25152903 Drive cover decal
26143603 Pan head tapping screw no. 10-24 x 2-3/4
28154990 Drive cover
3751152 Locknut #10-24
31132010 Hex flange nut
32137052 Drive pulley
35151521 Adjuster
36702511 Gear case assembly
37137090 Spring
38STD541425 Locknut 1/4-20
4158755 Screw, machine, pan head 1/4-20 x 2-3/16
4075192 Spring
41151520 Kit, wheel adjuster, rh (includes knob and bear...
5146527 V-belt
53144747 Frame
54166069 Grass bag
5586012 Driveshaft cover
57144748 Frame
6150495 Spring . retainer
8150182 Hub cap
9145212 Hex nut