Register / log-in to add to your Hammerwall Collection.
Manual Location

The Search Results for the Search Section to the left will appear here.

Upload a pic of this item

Page: 1

I Model No . 831.100430 Serial No . Write the serial number in the space above for reference . Serial Number De QUESTIONS ? As a manufacturer , we are com - mitted to providing complete customer satisfaction . If you have questions , or find that there are missing or damaged parts , we will guarantee complete satis - faction through direct assistance from our factory . TO AVOID UNNECESSARY DELAYS , PLEASE CALL DIRECT TO OUR TOLL - FREE CUSTOMER HOT LINE . The trained techni - cians on our customer hot line will provide Immediate assis - tance , free of charge to you . CUSTOMER HOT LINE : 1 - 888 - 936 - 4266 Patent Pending Mon . - Thu . , 8 : 00 am - - 6 : 30 pro ; Fri . , 8 : 00 am - - 6 : 00 pm EST USER'S MANUAL SEARS CANADA , INC . , TORONTO , ONTARIO M5B 208
Page: 2

TABLE OF GONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 CHOOSING A LOCATION FOR THE RENEW 900 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 USING THE RENEW 900 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 TROUBLE - SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Note . A PART LIST and an EXPLODED DRAWING are attached to the center Of th = s manual . 2
Page: 3

IMPORTANT SAFETY INSTRUCTIONS : _ iii _ : z : i ; • ii _ W _ ING : To reduce the risk of drowning _ ' _ _ tric shock , or serious iniury , read the following ir _ p _ ant precautions before using the RENEw 900 . READ AND FOLLOW ALL INSTRUCTIONS is the responsibility of the owner to ensure 13 . Keep all chemicals away ' from children pets . . . . . . . . . , , t _ n th6 _ pa cover orl : spa jet unit is r _ nnin iS not de _ igne _ to - _ _ pp should shut Off . Press the The spa jet _ nJt should resume ' 11i : Re _ oVe any water which may ation . If the spa j 3
Page: 4

. . _ 20 . Keep an - ele _ : [ ric _ appliances such as radTos , 4 27 . WARNING _ To reduce the risk of teJephones , televisions , and lightsat least Pregnant . women should consult five feet ( 1.52 meters ) away from thewater . phys € anbefore using the RENEW _ . : i Pregnant women should not use the R 21Z : : : _ wire connector is provided 0il the pUrni _ : 900 if the water temperature is ab _ motorof this i . init to connect a minimum N0 . ( 38 ° C ) ; the Unborn child could be serio 8AWG ( 804 mm 2 ) solid copper conductor harmed . between this unit and any metal equipment , : electrical enclosure made of meta , metal : . ; i : 28 . DANGERmTo reduce the . risk of dl water pipes , or conduit within f ve feet . : : . ; Prolonged immersion in the RENEW 9 _ ( ' i . 52m ) of the unit . " cause hyperthermia , a dangerous condil which occurs when the internal boc : i Donot ature riseS : several degrees / 900 within five feet body temperature hylSeffii _ rnlJa : are nausea RENEW 900 nesS , and fain : ring ] Effects i if each metal objc awareness , inabilityto ) motor ( " - : lnua us _ I the RENI _ : i ! 4
Page: 5

WARNING DECAL PLACEMENT The decals shown below have been placed on the RENEW 900 . If a decal is missing , or if it is not legible , please call our Customer Service Department toll - free at 1 - 888 - 936 - 4266 , Monday - Thursday , 8 : 00 am - 6 : 30 pro ; Friday , 6 : 00 am - 6 : 00 pm EST ( excluding ho { idays ) , to order a replacement deca £ Apply the decal in the location shown . AVOID DROWNING RISK • STAY OFF COVER - - WILL NOT SUPPORT WEIGHT . • KEEP CHILDREN AWAY . CHILDREN OR OBJECTS CANNOT BE SEEN UNDER COVER . • REMOVE STANDING WATER - - CHILD CAN DROWN ON TOP OF COVER . • REMOVE COVER ( SI COMPLETELY BEFORESSIBLE . ENTRY OF BATHERS - - ENTRAPMENT PO • NON - SECURED OR IMPROPERLY SECURED COVERS ARE A HAZARD , • FAILURE TO FOLLOW ALL INSTRUCTIONS MAY RESULT IN INJURY OR DROWNING . • THIS IS NOT A SAFETY COVER , ® IMAGE is a registered trademark of ICON Health & Fitness , Inc .
Page: 6

• BEFORE , YOU BEGIN Thank you for selecting the IMAGE = RENEW 900 . The Department toll - free at 1 - 888 - 936 - 4266 , Monday - innovative RENEW 900 offers the features and quality Thursday , 8 : 00 am - 6 : 30 pm ; Friday , 8 : 00 am - 6 : 00 pm of a traditional hot tub at an affordable price . Best of EST ( excluding holidays ) . To help us assist you , all , the RENEW 900 is fully portable , so you can take please note the product model number and serial it wherever there is an electrical outlet . The RENEW number before calling . The model number is 831 • 100430 . The serial number can be found on a 900 allows you to relax and unwind in the comfort of your own home . decal attached to spa jet unit ( see the front cover of this manual ) . For your benefit , read this manual carefully before using the IMAGE = RENEW 900 , If you have addition - Before reading further , please familiarize yourself with al questions , please call our Customer Service the parts that are labeled in the drawing below . Spa Cover Console ( Under Spa Cover ) Jet Unit r Cord Side Panel Ground Fault Circuit Locking Buckle Inflation Valve Interrupter ( GFCI ) 6
Page: 7

CHOOSING A LOCATION - FOR THE RENEW 900 There are many factors to consider when choosing a location to set up the RENEW 900 . These factors vary depending on whether you use the RENEW 900 inside or outside . We have listed several factors you may wish to consider as you decide where you want to use the RENEW 900 . If you set up the RENEW 900 inside : If you set up the RENEW 900 outside : 1 . The RENEW 900 will increase the level of humidi - 1 . You should check your local building codes con - ty in your home . The location you choose should cerning the use of outdoor spas . be well ventilated . You may need to install a venti - lation fan or use a dehumidifier . 2 . The location must be close to an electrical outlet . Do not use an extension cord with the RENEW 900 , 2 . The location must be close to an electrical outlet . Do not use an extension cord with the RENEW 900 . 3 . The RENEW 900 should be close to a source of water . 3 . The RENEW 900 should be close to a source of water . 4 . We recommend that you place the RENEW 900 on a water - and stain - resistant , non - slip surface . 4 . Do not use the RENEW 900 on carpet or other 5 . material that may be damaged by moisture . We Be sure that the location you choose is stable , it recommend that you place the RENEW 900 on a must be able to support the weight of the RENEW water - and stain - resistant , non - slip surface with a 900 when it is filled with water , plus the weight of floor drain for any water that may splash from the the occupants . The RENEW 900 weighs approxi - RENEW 900 . mately 2400 pounds when filled with water . . 5 . Be sure that the location you choose is stable . It Think about environmental factors , such as rair _ , must be able to support the weight of the RENEW wind , shade , sunlight , and so forth . 900 when it is filled with water , plus the weight of 7 . You should be able to monitor the use of the the occupants . The RENEW 900 weighs approxi - mately 2400 pounds when filled with water . RENEW 900 from your home , to prevent unautho - rized use by children . 6 . Do not use the RENEW 900 above a finished liv - . Be sure that there is room around the RENEW ing area , due to the risk of water damage . 900 to permit servicing of the unit . The diameter of 7 . Be sure that there is room around the RENEW the tub is 69 " . You should allow for this size , plus 900 to permit servicing of the unit . The diameter of the size of the spa jet unit , when choosing the location . the tub is 69 " . You should allow for this size , plus the size of the spa jet unit , when choosing the 9 . location . Be sure to note any other considerations , such as aesthetics or privacy concerns , which may affect 8 . Be sure to note any other considerations , such as the safety or enjoyment of using the RENEW 900 . aesthetics or privacy concerns , that may affect the safety or enjoyment of using the RENEW 900 . 7
Page: 8

ASSEMBLY - Before beginning assembly , carefully read the • Assembly requires the included air pump . following information and instructions : • Read each assembly step before you begin . • Place all parts in a cleared area and remove the packing materials ; do not dispose of the packing • During assembly , make sure that all parts are ori - ented as shown in the drawings . materials until assembly is completed . • Assembly requires two people . 1 . Before beginning assembly , be sure that you have read and understand the information in the box above and on the previous page . Unfold the pre - assembled Fabric Spa Su _ ' mund ( 8 ) and Side Panels ( 1 , 2 ) until the assembled unit is round . Check the serf - attaching connections between the Fabric Spa Surround ( 8 ) and Side Panels ( 1 , 2 ) to be sure that all connections are firm . Be sure that all six cover buckles are fully inserted through the slots lj in the Side Panels ( 1 , 2 ) . 2 . Unfold the Inflatable Spa Liner ( 9 ) . Attach the nozzle on the included air pump to the lnflate here valve on the side of the Inflatable Spa Liner ( 9 ) . Use the air pump to tilt the sides of the tnftatable Spa second Liner with air . Attach the nozzle on the air pump to the valve on _ ! Inflate here the floor of the Inflatable Spa Liner ( 9 ) . Use the air pump to fill the bottom of the Inflatable Spa Liner third with air . Attach the nozzle on the air pump to the valve on first top of the Inflatable Spa Liner ( 9 ) + Use the air pump to fill the cushion on top of the Inflatable Spa Liner with air . 3 3 . Be sure that the flap on the Fabric Spa Surround ( 8 ) is on the outside of the Fabric Spa Surround and Side Panels ( 1,2 ) . insert the Inflatable Spa Liner ( 9 ) into the Fabric Spa Surround . Align the valve in the Inflatable Spa Liner with the hole in the Fabric Spa Flap Surround and the Inflation Side Panel ( 2 ) . Flip the flap on the Fabric Spa Surround ( 8 ) over the low section of the Inflatable Spa Liner ( 9 ) . ] _ / Valve must ; , Z - - - be visible in this hole 8
Page: 9

4 . - • - . Remove the power cord from the Spa Jet U _ ! ! ( 13 ) . - With the help of a second person , place the Spa Jet Unit ( 13 ) over the Side Panel ( 1 ) and the section of the Inflatable Spa Liner ( 9 ) which does not have the cushion . Be extremely careful not to tear the Inflatable Spa Liner ( 9 ) as you slide the Spa Jet Unit into place . Cord 5 , Before you fill the RENEW 900 , be sure that it is in 5 , 9 the position you want , and that it can be easily ser - viced , if needed . Once the RENEW 900 is filled with water , it will need to be drained to be moved . Using a garden hose or other clean water source , begin filling the RENEW 900 , until the jet and filter openings on the Spa Jet Unit ( 13 ) are covered with water . Do not fill the RENEW 900 more than 20 " deep with water . i i After the RENEW 900 is full , you must prime the Spa Jet Unit ( 13 ) before using the RENEW 900 ( see PRIMING THE SPA JET UNIT on page 10 ) . . 6 . Attach the nozzle on the included air pump to the 6 valve on the Inflatable Cover ( 4 ) . Use the Air Pump to fill the Inflatable Cover ( 4 ) with air . Remove the nozzle from the Inflatable Cover , 4 Slide one of the straps on the inside of the Spa Cover ( 11 ) through one of the loops on the Inflatable Cover ( 4 ) . Attach the latch on the strap to the buckle on the other end . Attach the other three straps on the inside of the Spa Cover ( 11 ) through the loops on the inflatable Cover ( 4 ) in the same manner . 7 . Place the Spa Cover ( 11 ) over the Side Panels ( f , 7 11 2 ) and the Spa Jet Unit ( 13 ) . Be sure that the Spa Cover is properly centered and that the straps on the Spa Cover line up with the straps extend - ing from the slots in the Side Panels ( 1 , 2 ) . Snap each of the six latches on the Spa Cover ( 11 ) into the buckles on the straps extending from the slots in the Side Panels ( 1,2 ) . ' 13 1,2 Latches and Buckles 9
Page: 10

• USING THE RENEW 900 ' - The RENEW 900 is designed for up to four adults . or more amps . No other appliance should be on the The six water jets can be regulated to provide a relax - same circuit . Replace the power cord immediately if it ing massage to Sooth away stress , and the strength becomes damaged . of the water massage can be adjusted by the air con - trol . The RENEW 900 holds 300 gallons of water and The power cord is equipped with a Ground Fault offers an automatic , programmable heating ( 70 ° F to Circuit Interrupter ( GFCl ) , located at the end of ihe 104 ° F ) and filtration system . power cord . You should always test the GFCI before using the RENEW 900 . The guidelines below explain how to properly use the First , turn Onthe RENEW 900 by pressing the power RENEW 900 . Follow these guidelines to maintain the RENEW 900 for your long - term enjoyment . button on the console . Once the unit is running , press the GFC { " test " button . The RENEW 900 should shut PRIMING THE SPA JET UNIT off . Press the " reset " button . The RENEW 900 should resume normal operation . If the RENEW 900 contin - The water pump in the spa jet unit must be primed ues to run after the ' test " button is pressed , then the GFCI is damaged . Do not use the RENEW 900 until before you use the RENEW 900 ihe first time . You must also prime the pump before using the unit each the GFCI has been repaired or replaced by a qualified electrician . time you re - fill the RENEW 900 . STARTING THE RENEW 900 To prime the spa jet f / _ RIMER unit , remove the Once you have tested the GFCI , you should verify the primer cap from the water flow from the pumping unit . Set the air control console . Fill the spa jet unit with at least 64 on the console to the lowest setting ( see USING THE PCrimaper - - @ CONSOLE on the next page ) . The pumping unit wi1 ! oz . of water . Replace heat the water as it pumps . Cover the RENEW 900 and tighten the _ Z _ - - _ = - _ " with the spa cover . The spa cover must be tight . primer cap , IMPOR - The water will heat at about 1.7 ° F an hour with the TANT : The spa jet cover on . If you are using the RENEW 900 indoors , unit may be seriously damaged if the pump is not and the room temperature is maintained at 70 ° F , it will properly primed , or if the primer cap is not take approximately 20 to 28 hours for the water to replaced and fully tightened , reach the set temperature . PLUGGING IN THE RENEW 900 The temperature and water flow can be set or changed by the controls on the console ( see USING Once the RENEW 900 is filled with enough water to THE CONSOLE on the next page ) • cover the water jets and the pump has been primed , the power cord can be plugged in and the spa jet unit TESTING AND TREATING THE WATER can be turned on . Note : The first time the power cord is plugged in , the spa jet unit will turn on automatically . The RENEW 900 comes with a starter chemical pack for maintaining the water in the spa . Disregard the When connecting the power cord , plug the power cord directions on the individual packages of " QUICK pHix directly into a grounded circuit capable of carrying 15 It DOWN " and " QUICK pHix It UP . " However , the directions on the bottle of " Non - chlorine Shox " and Grounded circuit capable of " Bromine Base " are correct . Always keep the chemi - cals away from children and pets . carrying 15 or more amps _ , , The first time you use the spa , you should test and Test and Reset _ ' 1 _ treat the water . Once you have verified that the spa jet unit is functioning properly , and have allowed the water to circulate for a while , you should remove the spa cover and add 1 / 3 of the " Bromine Base " bottle , and 1 / 3 of the " Non - chlorine Shox " bottle to the water Buttons _ in the spa . Allow the water to circutate for five min - utes . You should now test the pH level of the water . GFC ! " " _ Use the included test strips to check the pH of the 10
Page: 11

SECURING THE SPA COVER water . Refer to the instructions on the test strip pack - aging to see how to use the test strips . The spa cover can be secured by snapping the latch - If the level is too low , add half of one of the " QUICK es on the spa cover into the buckles on the side panels . pHix It UP " packets to the water . Let the water circu - The buckles can be late through the spa jet unit for five minutes . Test the pH level again . Repeat until the pH level is correct . locked by inserting the key and turning it Latch . , If the level is too high , add half of one of the " QUICK clockwise a quarter I Buckle turn . To unlock the pHix It DOWN " packets to the water . Let the water cir - culate through the spa jet unit for five minutes . Test buckles , insert the key and turn it counter - the pH level again . Repeat until the pH level is correct . clockwise a quarter turn . Replace the spa cover and allow the water to contin - ue to heat . Always keep the buckles locked when the spa is See WATER CHEMISTRY on page 13 for information not in use . Keep the keys in a safe place , out of concerning proper water maintenance . the reach of children . DIAGRAM OF THE CONSOLE THERMOSTAT ON / OFF _ DIVERTER AIR CONTROL / PRIMER @ FR _ E USING THE CONSOLE Refer to the console diagram above . The function of On / Off : Turns the spa jet unit on and off . When you each console control is explained below : first press the on / off button , the spa jet unit will run at low speed , providing gentle hydrotherapy . Press the Primer : This opening allows you to prime the spa jet button again and the spa jet unit will run at high unit before operation ( see PRIMING THE SPA JET speed , providing more intense hydrotherapy . Press UNIT on page 10 ) . the button a third time and the spa jet unit will shut off . Diverter : Controls the flow of water through the hydro - therapy jets and the whirlpool jet . The direction The spa jet unit also features an automatic mode , of the flow can be adjusted by turning the diverter which heats and filters the water when the spa is left control . When the control is set to " front , " the flow will unattended . When the spa jet unit is first plugged in , or if the buttons on the console have not been used be through the hydro - therapy jets ; when it is set to " side , " the flow will be through the whirlpool jet ; when for longer than twenty minutes , the automatic mode it is set to " all , " the flow will be evenly distributed will begin filtering or heating the water , as needed . through both the hydro - therapy jets and the whirlpool Note : to keep the filter and heat cycles from run - ning , the power cord must be unplugged . jet . Air Control : Determines the amount of air that is in Thermostat : Controls the temperature of the water . The water heats at about 1.7 ° F an hour with the cover the spa jet system during operation . If the control is on . The thermostat can be set to heat the water from turned to the left , the amount of air flowing through 70 ° F to 104 ° F . Use a medical or other accurate ther - the jets will increase , If the control is turned to the right , the amount will decrease . mometer to check the temperature of the water . 11
Page: 12

SPA JET UNIT OPERATION ing the water for twenty - minutes to filter any impuri - ties . Also , if the water temperature falls below 40 ° F , The spa jet unit features five hydro - therapy jets , a the pump will begin circulating and heating the water whirlpool jet , a suction vent , and a filter housing . to prevent the water from freezing . DRAINING THE RENEW 900 The five hydro - therapy jets ( A ) , located on the front of the spa jet unit , focus the water massage on your neck and back . To drain the RENEW 900 , you must use a garden hose to siphon the water . Place one end of the hose in the RENEW 900 and hold it in front of a hydro - therapy jet until there is a flow of water coming out of the hose . Turn off the spa unit and unplug the power cord . The unit will be damaged if it is run without water circulating . Be sure the end of the hose in the RENEW 900 is on the floor of the spa . Cq J The whirlpool jet ( B ) , located on the left side of the spa jet unit , directs the flow of the water to create a whirlpool action in the RENEW 900 . The suction vent ( C ) , located on the right side of the spa jet unit , pulls the water into the spa unit , in DRAINING THE PUMP order to operate the system . The suction After the RENEW 900 is drained ( see DRAINING cover should always @ THE RENEW 900 above ) , the pump in the spa jet unit be in ptace over the should also be drained if the RENEW 900 will be suction vent . Never stored for more than thirty days , or if it may be c / operate the RENEW exposed to freezing temperatures . 900 without the suc - tion cover in place . To drain the pump , remove the spa jet J The filter ( D ) , is _ ocat - unit from the side pan - iter Cover ed on the left side of els . Be careful not to the spa jet unit , Screws tear the inflatable behind the filter cover . spa liner . Locate the The filter can be pump inside the spa ter Cover removed for cleaning jet unit . Remove the and replacement by Drain Plug drain plug from the removing the Filter pump . Tip the spa jet Cover and the two unit slightly , until all the water has drained from the filter cover screws and then pullihg the filter from the pump . Replace the drain plug . spa jet unit . The spa jet unit features an automatic filter cycle and freeze protection . If the spa jet unit has not been operated for three hours , the pump will begin circu [ at - 12
Page: 13

MAINTENANCE CLEANING THE INFLATABLE SPA LINER 4 . Keep all chemicals out of the reach of chil - dren and pets . The liner should be cleaned with a mild soap solution . 5 . Keep all containers closed tightly when Do not use solvents , The liner should always be clean not in use , and dry before being moved or stored . 6 . Never add water to the chemicals - - always add the chemicals to the water as directed . CHECKING AND CLEANING THE FILTER 7 . Always store chemicals in a cool , dry place . 8 . Always keep chemicals away from chil - The filter should be checked periodically for build - up dren end pets . of dirt and oil . If the filter needs to be cleaned , follow MAINTAINING THE PROPER PH BALANCE the steps below : 1 . Turn off the power . 2 . Remove the two screws and cover from the The pH factor is a measure of relative acidity or alka - spa jet . Then pull the filter out of the unit . linity in the water . It is measured on a scale of 1 to 14 . 3 . Check the filter for any dirt or debris . If the fil - Pure water has a value of 7 , which is neutral . Any ter needs to be cleaned , rinse the filter with a value above 7 is alkaline , and any value below 7 is hose . If the filter still is dirty , you will need to acidic . You should maintain a slightly alkaline pH soak it in a cleaning solution which can be level , between 7.2 and 7.8 , in the RENEW 900 . obtained from a pool and spa supply store . 4 . Inspect the filter for damage . Replace the fil - Severe problems can occur when the pH balance is ter if there are any signs of damage . not maintained within this range . If the pH level 5 . Re - insert the cleaned filter and re - attach the exceeds 7.8 , dissolved minerals can build - up and clog two screws and cover to the spa jet unit , the plumbing in the spa jet unit . If the pH level falls below 7.2 , the acid level in the water will begin to cor - MAINTAINING THE SPA COVER rode the metal parts in the spa jet unit . Also , the sani - tation agents in the water will not be effective if the pH The spa cover should be cleaned monthly . Remove level is not properly maintained . Damage caused by the inflatable cover from the spa cover , then hang the improper pH levels is not covered under the warranty . spa cover over a clothes line and spray it with a hose . Leave the cover on the clothes line until it is fully dry . To maintain the proper pH level , you should test the pH of the water regularly . To test the water you can WINTER USE AND CARE either purchase additional test strips or purchase a pH test kit at a pool and spa supply store . The pH read - The RENEW 900 is designed for year - round use . If ing should be between 7.2 and 7.8 . If the level is too you decide to store the RENEW 900 for the winter , low , add a pH increaser ( usually soda ash ) . If the store it in a warm , dry location . ( See DRAINING THE level is too high , add a pH reducer ( usually sodium RENEW 900 and DRAINING THE PUMP on page 12 . ) bisulfate ) . Test the water again after five minutes . See the instructions with your test strips or pH test kit for WATER CHEMISTRY additional information about testing and adjusting the pH . The RENEW 900 comes with a starter chemical pack SANITIZING THE RENEW 900 for maintaining the water in the spa . ( See TESTING AND TREATING THE WATER on page 10 . ) Additional chemicals can be purchased at a pool and spa supply Please refer to your local pool and spa supplier for store . information concerning which chemicals you should use in your area to sanitize the spa . CAUTION : The chemicals used to maintain the pH balance of the water and to sanitize the water can The most common sanitizing agent is a solid bromine be dangerous . Always follow these basic guide - concentrate . The amount required varies according to lines when handling the chemicals : several factors , such as user load , temperature , water conditions , and so forth . 1 . Always read and follow the directions on the label , unless directed otherwise . 2 . Never mix different chemicals . Proper water maintenance is a fairly complex process . 3 . Do not exceed the recommended We recommend that you contact your local pool and amounts - - follow the directions on the spa supplier for information on how you should best label closely . accomplish this . 13
Page: 14

TROUBLE " SHOOTING Most problems can be solved by following the simple steps below . Find the symptom that applies , and follow the steps listed . If further assistance is needed , call our Customer Service Department ton - free at 1 - 888 - 936 - 4266 , Monday - Thursday , 8 : 00 am - 6 : 30 pro ; Friday , 8 : 00 am - - 6 : 00 pm EST ( excluding holi - days ) . 1 . SYMPTOM : THE SPA WILL NOT OPERATE the air control to low . The water will heat at a rate of 1.7 ° F an hour . tfyou are using the spa a . Check the power cord . The power cord must indoors , and the room temperature is main - be plugged into a grounded outlet ( see PLUG - tained at 70 ° F , it will take approximately 20 to GING _ NTHE RENEW 900 on page 10 ) . 28 hours for the water to reach the set temper - ature . b . Check to see if the GFCI breaker is tripped , or was not turned on . Reset the GFCl breaker . b . If you are using the RENEW 900 outdoors , it may take longer for the water to heat . See the 2 . SYMPTOM : THE CIRCUIT BREAKER OR GFCl chart below for the approximate heating time . BREAKER TRIPS WHILE THE SPA IS OPERATING Air Temoerature Heatina Time 70 ° F + 20 to 28 hours a . Reset the circuit breaker . If the circuit breaker 50 ° F - 70 ° F 1 to 2 days trips again , contact a qualified electrician for 30 ° F - 50 ° F 2 to 3 days service . If the water stil [ has not heated after three 3 . SYMPTOM : THE PUMP HUMS days , contact our customer service department . 7 . SYMPTOM : THE WATER PULSATES OR a . The filter may be dirty or damaged . Remove THERE IS MINIMUM WATER FLOW the filter housing from the spa jet unit and clean or replace the filter . a . Adjust the water level . This usually occurs only when the water level is low . Add water until the b . The pump may have a foreign object stuck in the impeller . Contact our customer service filter and jets are covered . department . b . This problem is caused by excess air in the c . The pump may have a loose wire connection . pump circulation system . Check to see if the Contact our customer service department , • primer cap is fully tightened . Prime the pump again and fully tighten the primer cap ( see . SYMPTOM : THE PUMP HUMS BUT DOES NoT PRIMING THE SPA JET UNIT on page 10 ) . ROTATE 8 , SYMPTOM : THE SPA JET UNIT CAVITATES DURING USE a . The pump may be jammed . Contact our cus - tomer service department . a . Adjust the water level This usually occurs only 5 . SYMPTOM : THE PUMP IS NOISY WHILE when the water level is low . Add water until the OPERATING filter and jets are covered . a . There may be debris in the pump . Contact our b . This problem is caused by excess air in the pump circulation system . Check to see if the customer service department . primer cap is fully tightened . Prime the pump b . The pump may have a bad bearing . Contact again and fully tighten the primer cap ( see PRIMING THE SPA JET UNIT on page 10 ) . our customer Service department . 6 . SYMPTOM : THE WATER DOES NOT HEAT SYMPTOM : THE WATER IS NOT BEING 9 . CLEANED BY THE FILTER a . The heater is attached to the pump in the spa a . Check to see if the filter is in place . Clean the jet unit . If the pump is operating , the water should heat . Cover the RENEW 900 with the filter if it is dirty . spa cover . The spa cover must be tight . Set 14
Page: 15

b . Check the chemical balance of the water . If the 11 . sYMPToM : THEWATER LEVEL DROPS i . pH is incorrect , the sanitizing agents will not function properly . a . Some water loss due to evaporation is normal . If rapid water loss eccurs , or if you notice wet - 10 . SYMPTOM : THE SPA JET UNIT CONTINUES ness on the floor around the RENEW 900 , then TO RUN AFTER IT HAS BEEN SHUT OFF the liner may have a leak . Locate the leak , and patch it using a pool patch kit that you can pur - chase at any pool and spa supply store . a . When you press the on / off button once , the spa jet unit will run at low speed , heating the water . b . A clamp or seal inside the spa jet may be Press the button again and the spa jet unit will run at high speed , filtering the water . Press the loose . Check the floor around the spa jet unit button a third time and the spa jet unit will shut for excess water , and watch the spa jet unit off . The spa jet unit also features an automatic while it is operating to see if water drips from mode , which heats and filters the water when the spa jet unit housing . If you can identify the the spa is left unattended . When the spa jet location of the leak inside the spa jet unit , tight - unit is first plugged in , or if the buttons on the en the clamp - or replace the damaged seal . console have not been used for longer than 12 . SYMPTOM : THE INFLATABLE SPA LINER twenty minutes , the automatic mode will begin LOSES AIR filtering or heating the water , as needed . To keep the filter and heat cycles from running , the power cord must be unplugged . Special a . Over time , some air loss is normal , If rapid air Note : If the unit is to be kept outdoors in loss occurs , then the liner may have an air cold weather , you must allow the spa to leak . Locate the leak , and patch it using a pool maintain a safe temperature by running in patch kit that you can purchase at any pool and automatic mode . Allowing the spa jet unit to spa supply store . freeze will damage the unit . If you do not want to use the spa during the winter , store it in a warm , dry location ( see WINTER USE AND CARE on page 13 ) . 15
Page: 16

- ORDERING - REPLACEMENT iSARTS To order replacement parts , simply call our Customer Service Department toll - free at 1 - 888 - 936 - 4266 , Monday - Thursday , 8 : 00 am - - 6 : 30 pm ; Friday , 6 : 00 am - - 6 : 00 pm EST ( excluding holidays ) . To help us assist you , please be prepared to give the following information when calling : 1 . The MODEL NUMBER of the product ( 831.100430 ) . 2 . The NAME of the product ( IMAGE ° RENEW 900 ) . 3 . The SERIAL NUMBER of the product ( see the front cover of this manual ) . 4 . The KEY NUMBER and DESCRIPTION of the part ( s ) ( see the PART LIST / EXPLODED DRAWING attached to the center of this manual ) . Part No . 154868 J00726 - C R0499A Printed in USA © 1999 ICON Health & Fitness , Inc . 16
Page: 17

LIMITED FIVE YEAR MASSAGE SPA WARRANTY ICON OF / DU CANADA INC . , ( ICON ) , warrants this product to be free from defects in workmanship and material , under nor - mal use and service conditions , for a period of ninety ( 90 ) days from the date of purchase . ICON extends a limited five ( 5 ) year warranty on the spa shell structure . ICON also extends a limited two ( 2 ) year warranty on the pump and motor . This warranty extends only to fhe original purchaser . ICON's obligation under this warranty is limited to replacing or repairing , at ICON's option , the product through one of its authorized service centers . All repairs for which warranty claims are made must be pre - authorized by ICON . This warranty does not extend to any product or damage to a product caused by or attributable to freight damage , abuse , misuse , improper or abnormal usage , or repairs not provided by ICON authorized service per - sonnel , to products used for commercial or rental purposes , or to products used as store display models . Specifically exclud - ed are damages caused by or attributable to the following incidents : any damage to the wood exterior resulting from improp - er maintenance , or any damage to the wood or tile extedor attributable to freight mishandling ; damage resulting from improp - er winterization ; damage to the spa shell resulting from improper chemical treatment , damage to the spa shell resulting from exposure to extreme temperatures , or damage to the spa shell resulting from exposure to direct sunlight and ultraviolet rays while the spa is empty ; damage to the pump , motor , plumbing , and components dueto improper maintenance , chemical treatment , or exposure ; damage resulting from failure to properly follow user's manual installation , operating , or mainte - nance instructions . Also excluded are consumable components , including but not restricted to headrests , filter cartridges , and light bulbs . No other warranty beyond that specifically set forth above is authorized by ICON . ICON is not responsible or liable for indirect , special or consequential damages adsing out of or in connection with the use or performance of the product or damages with respect to any economic loss , loss of or damage to property including water damage , loss of revenues or profits , loss of enjoyment or use , costs of removal , installation or other consequential damages of whatsoever nature . Some provinces do not allow the exclusion or limitation of incidental or consequential damages . Accordingly , the above limitation may not apply to you . The warranty extended hereunder is in lieu of any and ell other warranties and any implied warranties of merchanfability or fitness for a particular purpose is limited in its scope and duration to the terms sef forth herein . Some provinces do nor allow limitations on how long an implied warranty lasts . Accordingly , the above [ imitationmay not apply to you . This warranty gives you specific legal rights . You may also have other rights which vary from province to province . ICON OF / DU CANADA , 900 de l'lndustrie , St . Jerbme , QC J7Y 4B8 IMAGE PRODUCT WARRANTY REGISTRATION IMPORTANT : MAIL WITHIN 14 DAYS OF PURCHASE NAME : PHONE : ADDRESS : COUNTY : POSTCODE : MODEL NO . SERIAL NO PURCHASE DATE : RETAILER NAME : RETAILER ADDRESS : 8 ) Did you conslder purchasing fimess equlpment Irom anoIher 1 ) Primary user ( s ) of product : manu [ acturer ? _ 1 Male _ Female O Family [ ] NO [ 3 Yes 2 ) Age of primary user : What other Manufacturer ? 0 - 24 [ 3 35 - 44 [ _ ] 5 _ 4 E _ 25 - 34 El 45 - 54 O 65 and over 9 ) Based on your impression of wha { you have purchased , would you boy another ICON product ? Annual household income : 3 ) ( 3 Yes D No O NO Opinion D o - e , g99 [ 3 15,000 - 19,999 If not , what other brand name equipment would you purchase ? [ ] 10,000 - 14,999 [ 3 20,000 + 4 ) How many times a week do you exercise ? 10 ) Wna { other type of exercise equipment do you own ? [ 3 Less than 3 limes [ 3 S times or more [ 3 Bicycle [ ] Exercise Cycle FJ Treadmill Home Gym [ 3 Weight Bench CI SIepper s ) Have you ever purchased an ICON product before ? [ 3 Cardio Glide FJ Other [ 3 Yes [ 3 NO 11 ) Which type of magazines do you read rec ; ulad " . ; y , ? e ) Where did you first see or hear about ICON preducls ? [ 3 Sports [ ] Fitness 13 Molohng _ 1 Magazine [ ] Friend / relalive El Business [ 3 Compuler [ 3 General El NewspaperAd [ 3 SEore [ 3 Other 12 ) Do you ' Msh to be sent further bu ! lelinsabout ICON produ ¢ ls ? [ 3 Yes [ ] No 7 ) What was the pdrnary reason ler purchasing this ICON proOuct ? [ 3 SIo _ e Employee El Television Ads [ ] Cotour THANK YOU FOR YOUR TIME FJ Elech'Onic Features _ 1 Magazine Ads El Price [ 3 Product Design [ 3 Producl Innovation C ) 1999 ICON el Canada , Inc . Pdnted in USA D Other Fealures 17
Page: 18

A . REFEREN - CES N ° . du ModUle : N ° . de S _ rie : Nom du Ddtaillant : Date d'Achat : Adresse du D _ tail ! ant : AFFRANCHIR SUFFtSAMMENT ICON of / du Canada Inc . 900 de l'lndustrie St - J _ rSme , Qu6bec Canada , J7Y 4B8 18
Page: 19

PART LIST'Model No . 831.100430 Ro4ggA Key No . Qty . Description Key No . Qty . Description 1 1 Side Panel 33 1 Rubber Damper 2 1 Power Cord Grommet 34 1 Wire Harness 1 Air Control Knob 3 1 Dual Temperature Probe 35 4 1 Inflatable Cover 36 1 On / Off Switch Assembly 1 Thermostat Knob 5 4 Clamp Screw 37 6 4 Clamp 38 1 Primer Cap 7 4 Bolt 39 16 Housing Screw 8 1 Fabric Spa Surround 40 1 Console Overlay 1 Micro Switch / Wire 9 1 Inflatable Spa Liner 41 10 4 Spa Jet Nozzle 42 2 - Control Mounting Screw 11 1 Spa Cover 43 2 Control Mounting Nut 1 Motor Mount Bracket i2 2 Heater O - ring 44 13 1 Spa Jet Unit 45 2 Housing Support Bracket 14 1 Heater Housing 46 5 Cable Clamp 15 2 Filter Cover Screw 47 1 Filter Cover 16 1 Filter 48 2 3 / 8 " Compression Fitting 17 1 Cover Screw 49 1 Temperature Tube 18 1 Suction Cover 50 1 Trim 19 1 Suction Fitting 51 1 Primer O - ring 20 1 Pump Motor 52 2 Short Head Fitting 21 1 Heater Terminal Cover 53 1 Motor Endcap 22 1 Heat Controller 54 1 Motor Cap Screw 1 Pressure Switch 23 1 Heater Wire Harness 55 1 Heater Ground Wire 24 2 Cover Nut # 25 1 Electronic Control # 1 Air Pump 26 1 Tri - jet Nozzle # 2 Key 1 Starter Chemical Pack 27 1 Headrest w / Fasteners # 28 4 Nut # 1 Chemical Test Strip Pack 29 1 Heat Control Nut # 1 Warning Decal 30 4 Rubber Insulator # . 1 User's Manual 31 4 Washer # 1 Video 32 1 Whirlpool Jet Note : " # " indicates a non - illustrated part . Specifications are subject to change without notice . 19
Page: 20

EXPLODED DRAWING - - - Model No . 831.100430 R0499A rr ( 3o