Home | Manufacturer Directory | UPC Lookup | Wanted Manuals | Information Pages |
Register Login | Members Area |

Back To MTD Tiller - Cultivator       Model: 21A332C731 MTD 6 HP Front Tine Tiller Owners Manual
Regular Text Search or Search by Model Number

Register / log-in to add to your Hammerwall Collection.
Manual Location


Upload a pic of this item

Manuals For Same Model Number.
21A332C731 MTD 6 HP Front Tine Tiller Owners Manual...

Other Model Numbers Referenced to The Same Manual.
21A303C700 MTD 3.5 HP Front Tine Tiller Owners Manual...
21A332A700 MTD 5 HP Front Tine Tiller Owners Manual...
21A332A752 MTD Front Tine Tiller Owners Manual...
21A332B729 MTD Front Tine Tiller Owners Manual...
21A332C765 MTD 6 HP Front Tine Tiller Owners Manual...
21A333A729 MTD 5 HP Front Tine Tiller Owners Manual...

Other Items that are in the Same Category.
450 MTD Rear Tine Tiller...
21A-450 MTD Yard Machines Rear Tine Tiller...
300 MTD Front Tine Tiller...
330 MTD Front Tine Tiller...
340 MTD Front Tine Tiller...
341 MTD Front Tine Tiller...
342 MTD Front Tine Tiller...
343 MTD Front Tine Tiller...
344 MTD Front Tine Tiller...
345 MTD Front Tine Tiller...

This is a partial text extraction from the pdf, to download the pdf, click the Manual tab. If you want to search this text, hold control and F, and type the word you are looking for.

Page: 1

Operator’s Manual Front Tine Tiller Model Series 300 & 330 IMPORTANT : READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning : This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest - covered , brush - covered or grass - covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws ( if any ) . If a spark arrester is used , it should be maintained in effective working order by the operator . In the State of California the above is required by law ( Section 4442 of the California Public Resources Code ) . Other states may have similar laws . Federal laws apply on federal lands . A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department , P.O . Box 361131 Cleveland , Ohio 44136 - 0019 . MTD LLC , P.O . BOX 361131 CLEVELAND , OHIO 44136 - 0019 PRINTED IN U.S.A . 770 - 10564D FORM NO . ( 2 / 2004 )
Page: 2

TABLE OF CONTENTS Content Page Content Page Important Safe Operation Practices 3 Maintaining Your Tiller 10 Assembling Your Tiller 5 Troubleshooting 11 Know Your Tiller 6 Illustrated Parts List 12 Operating Your Tiller 7 Warranty 16 Making Adjustments 9 FINDING MODEL NUMBER This Operator’s Manual is an important part of your new tiller . It will help you assemble , prepare and maintain the unit for best performance . Please read and understand what it says . Before you start assembling your new equipment , please locate the model plate on the equipment and copy the information from it in the space provided below . A sample model plate is also given below . You can locate the model plate by standing at the operating position and looking down at the right side of the frame . This information will be necessary to use the manufacturer’s web site and / or help from the Customer Support Department or an authorized service dealer . Copy the model number here : MTD LLC Copy the serial number here : P . O . BOX 361131 CLEVELAND , OH 44136 1330 - 220 - 46830 www.mtdproducts.com 800 - 800 - 73 CUSTOMER SUPPORT Please do NOT return the unit to the retailer from where it was purchased , without first contacting Customer Support . If you have difficulty assembling this product or have any questions regarding the controls , operation or maintenance of this unit , you can seek help from the experts . Choose from the options below : Visit mtdproducts.com for many useful suggestions . Click on Customer Support button and you will get the four options reproduced here . Click on the appropriate button and help is immediately available . The answer you are The answer you are looking for could be just looking for could be just a mouse click away ! a mouse click away ! If you prefer to reach a Customer Support Representative , please call 1 - 800 - 800 - 7310 . The engine manufacturer is responsible for all engine - related issues with regards to Engine performance , power - rating , specifications , warranty and service . Please refer to the engine Manual manufacturer’s Owner’s / Operator’s Manual , packed separately with your unit , for more information . 2
Page: 3

SECTION 1 : IMPORTANT SAFE OPERATION PRACTICES WARNING : This symbol points out important safety instructions which , if not followed , could endanger the personal safety and / or property of yourself and others . Read and follow all instructions in this manual before attempting to operate this machine . Failure to comply with these instructions may result in personal injury . When you see this symbol — heed its warning . WARNING : Engine exhaust , some of its constituents , and certain vehicle components contain or emit chemicals known to State of California to cause cancer and birth defects or other reproductive harm . DANGER : This machine was built to be operated according to the rules for safe operation in this manual . As with any type of power equipment , carelessness or error on the part of the operator can result in serious injury . This machine is capable of amputating hands and feet . Failure to observe the following safety instructions could result in serious injury or death . 7 . Use only an approved gasoline container . Training 8 . Extinguish all cigarettes , cigars , pipes and other 1 . Read , understand , and follow all instructions on the sources of ignition . machine and in the manual ( s ) before attempting to 9 . Never fuel machine indoors . assemble and operate . Keep this manual in a safe 10 . Never remove gas cap or add fuel while the engine place for future and regular reference and for is hot or running . ordering replacement parts . 11 . Allow engine to cool at least two minutes before 2 . Be familiar with all controls and their proper refueling . operation . Know how to stop the machine and 12 . Never over fill fuel tank . Fill tank to no more than ½ disengage them quickly . inch below bottom of filler neck to provide space for 3 . Never allow children under 14 years old to operate fuel expansion . this machine . Children 14 years old and over should 13 . Replace gasoline cap and tighten securely . read and understand the operation instructions and 14 . If gasoline is spilled , wipe it off the engine and safety rules in this manual and should be trained equipment . Move machine to another area . Wait 5 and supervised by a parent . minutes before starting the engine . 4 . Never allow adults to operate this machine without 15 . Never store the machine or fuel container inside proper instruction . near an open flame , spark or pilot light ( e.g . 5 . Keep bystanders , helpers , pets and children at least furnace , water or space heater , clothes dryer etc . ) . 75 feet from the machine while it is in operation . 16 . Allow machine to cool 5 minutes before storing . Stop machine if anyone enters the area . Operation Preparation 1 . Do not put hands or feet near rotating parts . Contact 1 . Thoroughly inspect the area where the equipment is with the rotating parts can amputate hands and feet . to be used . Remove all stones , sticks , wire , and 2 . Do not operate machine while under the influence other foreign objects which could be tripped over of alcohol or drugs . and cause personal injury . 3 . Never operate this machine without good visibility 2 . Wear sturdy , rough - soled work shoes and close or light . Always be sure of your footing and keep a fitting slacks and shirt . Loose fitting clothes or firm hold on the handles . jewelry can be caught in movable parts . Never 4 . Keep bystanders , helpers , pets , and children at operate this machine in bare feet or sandals . least 75 feet from the machine while it is in 3 . Disengage clutch levers and shift ( if provided ) into operation . Stop the machine if anyone enters the neutral ( “ N ” ) before starting the engine . area . 4 . Never leave this machine unattended with the 5 . Be careful when tilling in hard ground . The tines engine running . may catch in the ground and propel the tiller 5 . Never attempt to make any adjustments while forward . If this occurs , let go of the handle bars and engine is running , except where specifically do not restrain the machine . recommended in the operator’s manual . 6 . Exercise extreme caution when operating on or 6 . To avoid personal injury or property damage use crossing gravel surfaces . Stay alert for hidden extreme care in handling gasoline . Gasoline is hazards or traffic . Do not carry passengers . extremely flammable and the vapors are explosive . 7 . Never operate the machine at high transport Serious personal injury can occur when gasoline is speeds on hard or slippery surfaces . spilled on yourself or your clothes which can ignite . 8 . Exercise caution to avoid slipping or falling . Wash your skin and change clothes immediately . 3
Page: 4

9 . Look down and behind and use care when in 4 . Do not change the engine governor settings or over - reverse or pulling machine towards you . speed the engine . The governor controls the 10 . Start the engine according to the instructions found maximum safe operating speed of the engine . in this manual and keep feet well away from the 5 . Maintain or replace safety and instruction labels , as tines at all times . necessary . 11 . After striking a foreign object , stop the engine , 6 . Follow this manual for safe loading , unloading , disconnect the spark plug wire and ground against transporting , and storage of this machine . the engine . Thoroughly inspect the machine for any 7 . Never store the machine or fuel container inside damage . Repair the damage before starting and where there is an open flame , spark or pilot light operating . such as a water heater , furnace , clothes dryer etc . 12 . Disengage all clutch levers and stop engine before 8 . Always refer to the operator’s manual for proper you leave the operating position ( behind the instructions on off - season storage . handles ) . Wait until the tines come to a complete 9 . If the fuel tank has to be drained , do this outdoors . stop before unclogging the tines , making any 10 . Observe proper disposal laws and regulations for adjustments , or inspections . gas , oil , etc . to protect the environment . 13 . Never run an engine indoors or in a poorly ventilated area . Engine exhaust contains carbon Your Responsibility monoxide , an odorless and deadly gas . 1 . Restrict the use of this power machine to persons 14 . Muffler and engine become hot and can cause a who read , understand and follow the warnings and burn . Do not touch . instructions in this manual and on the machine . 15 . Use caution when tilling near fences , buildings and 2 . The safety label on the tiller is reproduced below for underground utilities . Rotating tines can cause your review . To ensure safe operation of the tiller , property damage or personal injury . follow the instructions on all labels closely . 16 . Do not overload machine capacity by attempting to till soil to deep at to fast of a rate . 17 . If the machine should start making an unusual noise or vibration , stop the engine , disconnect the spark plug wire and ground it against the engine . Inspect thoroughly for damage . Repair any damage before starting and operating . 18 . Keep all shields , guards and safety devices in place and operating properly . 19 . Never pick up or carry machine while the engine is running . 20 . Use only attachments and accessories approved by the manufacturer . Failure to do so , can result in personal injury . 21 . If situations occur which are not covered in this manual , use care and good judgment . Contact your dealer or telephone 1 - 800 - 800 - 7310 for assistance and the name of your nearest servicing dealer . Maintenance & Storage 1 . Never tamper with safety devices . Check their proper operation regularly . 2 . Check bolts and screws for proper tightness at frequent intervals to keep the machine in safe working condition . Also , visually inspect machine for any damage . 3 . Before cleaning , repairing , or inspecting , stop the engine and make certain the tines and all moving parts have stopped . Disconnect the spark plug wire and ground it against the engine to prevent unintended starting . 4
Page: 5

SECTION 2 : ASSEMBLING YOUR TILLER NOTE : This operator’s manual covers various models Handle of tillers . The units illustrated may vary slightly from Adjustment Lever your unit . Follow only those instructions which pertain to your model number . NOTE : References to right or left side of the tiller are determined from behind the unit in the operating position . To Remove Unit From Carton • Remove staples , break glue on top flaps , or cut tape at carton end and peel along top flap to open carton . • Remove loose parts included with unit ( i.e . , operator’s manual , etc . ) . • Cut corners and lay carton down flat . • Remove packing material . • Roll or slide unit out of carton . Check carton thoroughly for loose parts . • Extend control cable and lay on the floor . Be careful not to bend or kink control cable . Handle Adjustment Lever IMPORTANT : This unit is shipped without gasoline or oil in the engine . Be certain to service engine with gasoline and oil as instructed in the separate engine manual before operating your machine . Retainer Bracket Loose Parts In Carton Tailpiece and Depth Stake Lock Nut NOTE : All hardware needed for assembly is attached to the loose parts or the tiller . Before Assembly Figure 1 WARNING : Disconnect the spark plug wire and ground it against the engine to prevent unintended starting . Self - Tapping Screws Tailpiece Assembling The Handle • Remove the handle adjustment lever from handle and lift up upper handle to raise in operating position . See Figure 1 . • Reinsert adjustment lever through the lower hole , tightening the lever into lock nut on the retainer bracket . Lower Hole • Once the lever is in the lock nut , the handle can be moved to the desired position and then tighten securely . Attaching Tailpiece and Depth Stake • Remove the two self - tapping screws on the frame and slide the tailpiece into the frame , with the lower hole in the tailpiece toward the front . See Figure 2 . Figure 2 • Secure tailpiece with the screws just removed . 5
Page: 6

Check Cable Adjustment Clutch Lever • With the clutch lever disengaged , pull starter rope slowly several times . The tines should not turn . If they turn , the cable is not adjusted properly . • To adjust the cable , loosen the nut near the top of the cable and unscrew the cable to provide Loosen Nut additional slack in wire . See Figure 3 . • Tighten the nut and check again for proper adjustment . Figure 3 SECTION 3 : KNOW YOUR TILLER Tine Clutch Control Handle Adjustment Lever Depth Stake Tines Figure 4 WARNING : Read , understand , and Handle Adjustment Lever follow all instructions and warnings on The handle may be adjusted to the height desired . the machine and in this manual before Loosen the handle adjustment lever a few turns and operating . pivot handle up or down to desired position . Tighten lock . See Figure 4 . Tine Clutch Control The clutch control lever is located on the left handle . Throttle Control Squeezing the lever against the handle engages the The throttle control lever is located on the engine . It tine drive . Release the lever to stop the tines from controls the engine’s speed and stops the engine . turning . See Figure 4 . • With the throttle control pushed completely forward , the carburetor is in START or FAST position . Use Depth Stake maximum engine speed for deep tilling . • Pull the throttle control back to reduce engine The depth stake is located in the rear of the tiller and it speed to IDLE . Throttle control should be at IDLE controls the tilling depth . See Figure 4 . for transporting the tiller . • Pull the throttle completely back to stop the engine . 6
Page: 7

Choke Lever Engine Controls The choke lever is located near the throttle control . It is See the separate engine manual for additional used to enrich the fuel mixture when starting a cold information and functions of the engine controls . engine . Starter Handle The starter handle is located on the engine and is used to manually start the engine . SECTION 4 : OPERATING YOUR TILLER NOTE : See your engine manual packed with your unit WARNING : Read , understand , and for more detailed instructions . follow all instructions and warnings on the machine and in this manual before operating . Stopping Engine • Move throttle control lever to STOP or OFF Before Starting position . • Disconnect spark plug wire from spark plug and ground against the engine . Gas And Oil Fill - Up Service the engine with gasoline and oil as instructed in Using Your Tiller the separate engine manual packed with your tiller . Your tiller ( also known as a cultivator ) is a precision Read instructions carefully . built machine designed for seed bed preparation , WARNING : Use extreme care when cultivating , furrowing and mulching . It is engineered to handling gasoline . Gasoline is extremely minimize the hardest work in the vegetable or flower flammable and the vapors are explosive . garden , to till the soil for planting and cultivating , and to Never fuel machine indoors or while the perform many other useful labor saving tasks in the engine is hot or running . garden . Starting Engine Wheel Position The tiller is shipped with the wheels adjusted such that WARNING : Be sure no one is standing the unit sits level . While tilling , as the tines enter the in front of the tiller while the engine is ground and the front of the tiller lowers , the wheels running or being started . must be raised to level the unit , which is essential for proper engine operation . This adjustment is made by • Attach spark plug wire to spark plug . Make sure the removing the clevis pin and hairpin clip from wheel metal cap on the end of the spark plug is fastened yoke , raising the wheels to the desired height , and securely over the metal tip on the spark plug . replacing the clevis pin and hairpin clip . See Figure 5 . • Make sure that the tine clutch control is disengaged . Depth Stake • Place the throttle control in the FAST position . • Move choke lever to CHOKE position . A warm engine requires little or no choke . • Grasp starter handle and pull rope out slowly until engine reaches start of compression cycle ( rope will pull slightly harder at this point ) . Let the rope rewind slowly . • Pull rope with a rapid , continuous , full arm stroke . Keep a firm grip on starter handle . Let rope rewind slowly . Do not let starter handle snap back against starter . Repeat until engine starts . • When engine starts , move choke lever on engine Wheel Yoke Hairpin Clips halfway between CHOKE and RUN . As the engine & Clevis Pins warms up , move the lever to RUN position . Figure 5 7
Page: 8

When tilling , leave approximately 8 inches of untilled Controlling Speed And Tilling Depth soil between the first and second tilling paths , then Wheel Yoke Adjustment make the third path between the first and second . In some soils , the desired depth is obtained the first time Place wheel yoke so that the wheels are forward over the garden . In other soils , the desired depth is ( nearest point between wheels and tines ) for shallow obtained by going over the garden two or three times . In tilling , cultivating and transport . The forward speed will the latter case , the depth stake should be lowered increase . Turn yoke around ( farthest point between before each succeeding pass over the garden . Passes wheels and tines ) for deep tilling . Forward speed will should be made across the length and width of the decrease . See Figure 6 . garden alternately . Rocks which are turned up should be removed from the garden area . See Figure 8 . Position Wheel Yoke Position Wheel Yoke For Deep Tilling For Shallow Tilling Figure 6 Figure 8 Depth Stake Adjustment Handle Pressure The depth stake acts as a brake for the tiller and Further control of tilling depth and travel speed can be controls the depth and speed at which the machine will obtained by variation of pressure on the handles . operate . Remove the clevis pin and hairpin clip to raise • A downward pressure on the handles will reduce or lower depth stake . Refer to Figure 5 . the working depth and increase the forward speed . By increasing the depth of the depth stake , the forward • An upward pressure on the handles will increase speed of the machine is reduced and the working depth the working depth and reduce the forward speed . is increased . When the depth stake is raised , the The type of soil and working conditions will determine working depth of the machine is reduced and the the actual setting of the depth stake and the handle forward speed is increased . The working depth of the pressure required . machine may be predetermined by setting the depth Transporting the Tiller stake and wheels so that the wheels are about four • To transport the tiller to or from the garden , pivot inches from the ground when the tines and depth stake the depth stake forward and out of the way . With are resting on the ground . This setting will permit a the throttle control in SLOW position , the unit will working depth of about four inches . When presetting walk freely on the lawn . If the operator does not the working depth , the handles should be adjusted so allow the tiller to move freely , the unit will start to till the hand grips are a little above waist . The tiller will be the surface . Refer to Figure 7 . lower when the tines and depth stake penetrate the ground . See Figure 7 . Cultivating For cultivating , a two to three inch depth is desirable . Transport Depth Stake Setting the wheels and depth stake so that the wheels Position are about two inches above the ground while the tiller is resting on the tines and depth stake will allow the machine to work at cultivating depth . The throttle should be set to control forward movement to a slow walking speed . With the outer tines installed , the Shallow working width of the machine is 22 or 24 inches . Tilling Deep Tilling Wheel Setting For Deep Tilling Figure 7 8
Page: 9

The tiller has many uses other than tilling and For cultivation , this may be reduced to 13 inches by cultivating a garden . One of these is the preparation of removing the outer tines . Refer to the Adjustment lawn area for seeding . The tiller will prepare a deep Section . When laying out plant rows , be sure to allow seed bed which will be free of hard untilled spots , enough width to permit cultivation between the rows . In allowing a better stand of grass to grow . The tiller is growing corn or similar crops , check - row planting will very useful for loosening hard soil for excavation with a permit cross cultivation and practically eliminate hand shovel . No tedious handwork will be necessary . Your hoeing . See Figure 9 . tiller may be used for mixing compost in the pile , or for mixing it with the soil in your garden . This should be done after the soil has been broken to the full working depth . The compost should be worked in to a depth of six to seven inches . This may be done by working the length of the garden and then by making separate passes across its width . The addition of decayed organic matter will substantially increase the fertility of your garden . For proper decaying action , fertilizer should be applied and worked in with the mulch materials . Breaking up leaves and straw and mixing it with several inches of soil causes the soil to hold Figure 9 moisture longer and allows proper aeration of the plant root system . This also retards the growth of weeds . SECTION 5 : MAKING ADJUSTMENTS WARNING : Disconnect the spark plug wire and ground it against the engine before performing any adjustments . Engine Adjustment Refer to the separate engine manual for engine adjustment instructions . Wheel Adjustment 22 ” To adjust the wheel yoke and wheel position , refer to the Operating Section . Depth Stake Adjustment To adjust the depth stake to a desired position , refer to the Operating Section . Clutch Control Adjustment 24 ” Periodic adjustment of the belt tension may be required due to normal stretch and wear on the belt . To adjust the clutch control lever , refer to the Assembly Section . Tine Width Adjustment The tilling width of the unit is 22 inches . Tilling width can be increased to 24 inches by removing the clevis pins and hairpin clips , sliding the outer tines out one inch , and securing in this position with the clevis pins and 13 ” hairpin clips . For cultivation , reduce the tine width to 13 inches by removing the outer tines completely . Figure 10 See Figure 10 . 9
Page: 10

SECTION 6 : MAINTAINING YOUR TILLER WARNING : Disconnect the spark plug Cleaning Tine Area wire and ground it against the engine Clean the underside of the tine shield after each use . before performing any repairs or The dirt washes off the tines easier if rinsed off maintenance . immediately instead of after it dries . Always towel dry the tiller afterwards and apply a light coat of oil or Engine silicone to prevent rusting or water damage . Refer to the separate engine manual for engine IMPORTANT : Never use a " pressure washer ” to clean maintenance instructions . your tiller . Water can penetrate tight areas of the tiller Maintain engine oil as instructed in the separate and its chain case and cause serious damage to the engine manual packed with your unit . Read and follow unit . instructions carefully . Service air cleaner every ten hours under normal Belt Replacement conditions . Clean every hour under extremely dusty Your tiller has been engineered with a belt made of conditions . Poor engine performance and flooding special material ( Kevlar Tensile ) for longer life and usually indicates that the air cleaner should be better performance . It should not be replaced with an serviced . To service the air cleaner , refer to the off - the - shelf belt . Order all belts through your separate engine manual packed with your unit . authorized service dealer . IMPORTANT : Never run your engine without air cleaner • Disconnect and ground spark plug wire against the completely assembled . engine . • Remove the two hex washer screws from the front The spark plug should be cleaned and the gap reset of the belt cover and remove the lock nut and flat every 25 hours of engine operation . Spark plug washer from the side of the belt cover . replacement is recommended at the start of each tiller • Remove the belt cover . See Figure 11 . season ; check engine manual for correct plug type and Belt Cover gap specification . Clean the engine regularly with a cloth or brush . Keep the cooling system ( blower housing area ) clean to Hex Washer permit proper air circulation which is essential to engine Lock Nut & Screw performance and life . Be certain to remove all dirt and Flat Washer combustible debris from muffler area . Lubrication Transmission The transmission is pre - lubricated and sealed at the factory . It requires no checking . See an authorized Hex Washer Screw service dealer for any service issues . Clutch Handle Figure 11 Lubricate the pivot point on the clutch handle and the • Remove the hex screw and idler pulley from the cable at least once a season with light oil . The control idler bracket assembly . See Figure 12 . must operate freely in both directions . Pivot Points Lubricate all pivot points and linkages at least once a season with light oil . Hex Screw Tine Shafts Remove tine assemblies and lubricate the tine shafts at least once a season . Wheel Shafts Remove wheel assemblies and lubricate the axle shafts Idler Pulley at least once a season . Figure 12 10
Page: 11

• Refer to the engine manual for correct engine • Reassemble the new belt and reattach idler pulley storage instructions . to secure in place . • Wipe tines with oiled rag to prevent rust . • Replace belt cover assembly and secure with the • Store tiller in a clean , dry area . Do not store next to hardware removed earlier . corrosive materials , such as fertilizer . Off - Season Storage NOTE : When storing any type of power equipment in If the tiller will not be used for a period longer than 30 an unventilated or metal storage shed , care should be days , the following steps should be taken to prepare the taken to rustproof the equipment . Using a light oil or tiller for storage . silicone , coat the equipment and especially any springs , bearings , and cables . • Clean the exterior of engine and the entire tiller thoroughly . Lubricate the tiller as described in the lubrication instructions . • We do not recommend the use of pressure washers to clean your unit . They may cause damage to spindles , pulleys , bearings or the engine . The use of pressure washers will result in shortened life and reduce serviceability . SECTION 7 : TROUBLESHOOTING Problem Cause Remedy 1 . Connect wire to spark plug . Engine fails to start 1 . Spark plug wire disconnected . 2 . Fill tank with clean , fresh gasoline . 2 . Fuel tank empty or stale fuel . 3 . Move throttle lever to start position . 3 . Throttle control lever not in correct starting position . ( If equipped ) 4 . Move lever to ON position . 4 . Choke not in ON position . 5 . Clean fuel line . 5 . Blocked fuel line . 6 . Clean , adjust gap , or replace . 6 . Faulty spark plug . 7 . Wait a few minutes to restart , but do not 7 . Engine flooded prime . ( If Equipped ) 1 . Connect and tighten spark plug wire . Engine runs erratic 1 . Spark plug wire loose . 2 . Move choke lever to OFF position . 2 . Unit running on CHOKE . 3 . Clean fuel line ; fill tank with clean , fresh 3 . Blocked fuel line or stale fuel . gasoline . 4 . Clear vent . 4 . Vent plugged . 5 . Drain fuel tank . Refill with fresh fuel . 5 . Water or dirt in fuel system . 6 . Clean following engine manual . 6 . Dirty air cleaner . 7 . Refer to engine manual . 7 . Carburetor out of adjustment . 1 . Fill crankcase with proper oil . Engine overheats 1 . Engine oil level low . 2 . Clean air cleaner . 2 . Dirty air cleaner . 3 . Remove blower housing and clean . 3 . Air flow restricted . 4 . Refer to engine manual . 4 . Carburetor not adjusted properly . 1 . Stop tiller completely , check and Tines do not engage 1 . Foreign object lodged in tines . discard foreign object . 2 . Replace tine clevis pin ( s ) . 2 . Tine clevis pin ( s ) missing . 3 . Adjust control cable . 3 . Control cable not adjusted properly . 4 . Replace belt . 4 . Belt worn and / or stretched . 5 . Take unit to authorized service dealer . 5 . Pulley and idler not in correct adjustment . NOTE : For repairs beyond the minor adjustments listed above , contact your nearest service dealer . 11
Page: 12

SECTION 8 : MODEL SERIES 300 & 330 PARTS LIST 2 1 3 5 4 6 8 7 5 9 6 10 12 13 5 14 11 15 22 16 9 14 27 17 20 19 18 10 10 62 21 61 28 63 29 66 30 24 14 35 24 23 64 65 32 42 46 43 33 31 52 56 44 53 54 45 37 55 66 59 60 39 38 34 40 47 58 49 48 50 51 57 56 12
Page: 13

Model Series 300 & 330 Ref . Ref . Part No . Part Description Part No . Part Description No . No . 1 . 720 - 0274 Grip 35 . 711 - 0919 Belt Cover Bolt 2 . 731 - 0473 Clutch Grip 37 . 786 - 0035A Tine Shield 20 ” 3 . 686 - 0002 Clutch Lever 38 . 710 - 0502A Hex Washer Screw 3 / 8 - 16 x 1.25 4 . 649 - 0137 Handle Assembly 39 . 710 - 3008 Hex Cap Screw 5 / 16 - 18 5 . 712 - 0442 Lock Nut Cap 1 / 4 - 20 40 . 786 - 0053 Tine Shield Bracket 20 ” 6 . 738 - 1225 Shoulder Screw 42 . 786 - 0039B Cover Bracket 7 . 746 - 1148 Clutch Cable 43 . 736 - 0119 Lock Washer 5 / 16 8 . 738 - 1226 Shoulder Screw 44 . 710 - 0107 Hex Cap Screw 5 / 16 - 24 x . 50 9 . 710 - 0189 Hex Cap Screw 5 / 16 - 18 x 3.0 45 . 750 - 0892 Input Spacer . 64 ID x 2.4 Lg 10 . 736 - 0242 Bell Washer . 340 ID x . 872 OD 46 . 748 - 0350 Pulley Adapter 11 . 786 - 0340 Adjustable Handle Crank 47 . 756 - 0971 Engine Inner Half Pulley 12 . 710 - 0606 Hex Cap Screw 1 / 4 - 20 x 1.5 48 . 756 - 0972 Engine Outer Half Pulley 13 . 719 - 0279 Rope Guide 49 . 754 - 0428 Belt 14 . 712 - 0720 Flange Nut 5 / 16 - 18 50 . 736 - 0452 Bell Washer . 396 ID x 1.140 OD 15 . 786 - 0341 Retainer Bracket 51 . 710 - 0152 Hex Cap Screw 3 / 8 - 24 x 1.0 16 . 649 - 0136 Handle Tube 52 . 756 - 0585 Flat Pulley 17 . 710 - 0805 Hex Cap Screw 5 / 16 - 18 x 1.5 53 . 736 - 0312 Retainer Bearing Washer 18 . 711 - 0415 Clevis Pin 3 / 8 x 1.62 54 . 736 - 0112 Spherical Washer . 531 ID x . 620 OD 19 . 750 - 0890 Spacer 55 . 712 - 3029 Jam Nut 1 / 2 - 20 20 . 786 - 0003 Tailpiece Bracket LH 56 . 710 - 0599 Hex Washer Screw 1 / 4 - 20 x . 50 21 . 786 - 0004 Tailpiece Bracket RH 57 . 786 - 0056 Belt Cover 22 . 786 - 0005 Depth Bar 58 . 712 - 0392 Cap Lock Nut 1 / 4 - 28 23 . 714 - 0149B Cotter Pin 59 . 736 - 3020 Flat Washer . 271 ID x . 630 OD 24 . 712 - 3004A Hex Flange Locknut 5 / 16 - 18 60 . 738 - 0930 Shoulder Screw 27 . 710 - 0604A Hex Washer Screw 5 / 16 - 18 x . 625 61 . 712 - 0266 Jam Nut 3 / 8 - 16 28 . 710 - 0602 Hex Washer Screw 5 / 16 - 18 x 1.0 62 . 786 - 0144 Idler Bracket 29 . 738 - 0934 Shoulder Screw 63 . 786 - 0149 Idler Belt Keeper 30 . 712 - 0240 Jam Nut 7 / 16 - 20 64 . 756 - 0313 Flat Idler 31 . 736 - 0171 Lock Washer 7 / 16 65 . 710 - 0723 Hex Cap Screw 3 / 8 - 16 x 1.25 32 . 786 - 0138A Frame RH 66 . 686 - 0088 Idler Bracket Assembly 33 . 786 - 0139A Frame LH 13
Page: 14

Model Series 300 & 330 18 27 1 19 3 2 4 9 20 1 7 2 6 8 10 5 21 10 13 17 14 6 11 12 5 25 24 22 22 26 15 23 4 4 16 23 26 14
Page: 15

Model Series 300 & 330 Ref . Ref . Part No . Part Description Part No . Part Description No . No . 1 . 734 - 1988 Wheel 8 x 1.75 14 . 712 - 0240 Jam Nut 7 / 16 - 20 Inner Tine Assembly - RH 12 ” 15 . 734 - 1781 ‡ Wheel 8 x 1.8 2 ‡ 642 - 000 2 . 738 - 0929 Shoulder Screw Inner Tine Assembly - LH 12 ” 3 ‡ 642 - 000 3 . 686 - 0081A Wheel Bracket Assembly 16 . Outer Tine Assembly - RH 12 ” 642 - 0004 ‡ 4 . 714 - 0149B Cotter Pin Outer Tine Assembly - LH 12 ” 642 - 0005 ‡ 5 . 711 - 0415 Clevis Pin 17 . 710 - 0502A Hex Washer Screw 3 / 8 - 16 x 1.25 6 . 736 - 0242 Bell Washer . 340 ID x . 872 OD 18 . 712 - 3010 Hex Nut 5 / 16 - 18 7 . 710 - 0189 † Hex Cap Screw 5 / 16 - 18 x 3.0 19 . 736 - 0242 Bell Washer . 340 ID x . 872 OD Hex Cap Screw 5 / 16 - 18 x 2.75 6 ‡ 710 - 017 20 . 710 - 3180 Hex Cap Screw 5 / 16 - 18 x 1.75 8 . 738 - 0934 Shoulder Screw 21 . 750 - 0273 † Spacer , . 51 x . 69 x 1.97 9 . Engine Mounting Plate 786 - 0145A 22 . 04922 † Tine 9.5 ” RH 10 . 750 - 0470 Spacer . 47 OD x . 96Lg 23 . 04923 † Tine 9.5 ” LH 11 . 686 - 0189 † Chain Case Assembly 24 . 711 - 0702 † Clevis Pin Chain Case Assembly 686 - 0091 ‡ 25 . 04918 † Tine Adapter 12 . 712 - 0429 Hex Lock Nut 5 / 16 - 18 26 . 710 - 0599 † Self - tapping Screw , 1 / 4 - 20 x . 5 13 . 736 - 0171 Lock Washer 7 / 16 27 . 750 - 0456 † Spacer , . 790 x . 347 † Series 300 Only ‡ Series 330 Only 15
Page: 16

MANUFACTURER’S LIMITED WARRANTY FOR : The limited warranty set forth below is given by MTD LLC with e . MTD does not extend any warranty for products sold or respect to new merchandise purchased and used in the exported outside of the United States , its possessions United States , its possessions and territories . and territories , except those sold through MTD’s authorized channels of export distribution . “ MTD ” warrants this product against defects in material and f . Replacement parts that are not genuine MTD parts . workmanship for a period of two ( 2 ) years commencing on the g . Transportation charges and service calls . date of original purchase and will , at its option , repair or replace , free of charge , any part found to be defective in No implied warranty , including any implied warranty of materials or workmanship . This limited warranty shall only merchantability of fitness for a particular purpose , apply if this product has been operated and maintained in applies after the applicable period of express written accordance with the Operator’s Manual furnished with the warranty above as to the parts as identified . No other product , and has not been subject to misuse , abuse , express warranty , whether written or oral , except as commercial use , neglect , accident , improper maintenance , mentioned above , given by any person or entity , alteration , vandalism , theft , fire , water , or damage because of including a dealer or retailer , with respect to any product , other peril or natural disaster . Damage resulting from the shall bind MTD . During the period of the warranty , the installation or use of any part , accessory or attachment not exclusive remedy is repair or replacement of the product approved by MTD for use with the product ( s ) covered by this as set forth above . manual will void your warranty as to any resulting damage . The provisions as set forth in this warranty provide the Normal wear parts are warranted to be free from defects in sole and exclusive remedy arising from the sale . MTD material and workmanship for a period of thirty ( 30 ) days from shall not be liable for incidental or consequential loss or the date of purchase . Normal wear parts include , but not damage including , without limitation , expenses incurred limited to items such as : batteries , belts , blades , blade for substitute or replacement lawn care services or for adapters , grass bags , rider deck wheels , seats , snow thrower rental expenses to temporarily replace a warranted skid shoes , shave plates , auger spiral rubber and tires . product . HOW TO OBTAIN SERVICE : Warranty service is available , Some states do not allow the exclusion or limitation of WITH PROOF OF PURCHASE , through your local authorized incidental or consequential damages , or limitations on how service dealer . To locate the dealer in your area , check your long an implied warranty lasts , so the above exclusions or Yellow Pages , or contact MTD LLC at P.O . Box 361131 , limitations may not apply to you . Cleveland , Ohio 44136 - 0019 , or call 1 - 800 - 800 - 7310 or 1 - In no event shall recovery of any kind be greater than the 330 - 220 - 4683 or log on to our Web site at amount of the purchase price of the product sold . Alteration www.mtdproducts.com . of safety features of the product shall void this warranty . This limited warranty does not provide coverage in the You assume the risk and liability for loss , damage , or injury to following cases : you and your property and / or to others and their property arising out of the misuse or inability to use the product . a . The engine or component parts thereof . These items may carry a separate manufacturer’s warranty . Refer This limited warranty shall not extend to anyone other than the to applicable manufacturer’s warranty for terms and original purchaser or to the person for whom it was purchased conditions . as a gift . b . Log splitter pumps , valves , and cylinders have a HOW STATE LAW RELATES TO THIS WARRANTY : This separate one year warranty . limited warranty gives you specific legal rights , and you may c . Routine maintenance items such as lubricants , filters , also have other rights which vary from state to state . blade sharpening , tune - ups , brake adjustments , clutch adjustments , deck adjustments , and normal IMPORTANT : Owner must present Original Proof of deterioration of the exterior finish due to use or Purchase to obtain warranty coverage . exposure . d . Service completed by someone other than an authorized service dealer . MTD LLC , P.O . BOX 361131 CLEVELAND , OHIO 44136 - 0019 ; Phone : 1 - 800 - 800 - 7310 , 1 - 330 - 220 - 4683
Search in Tiller - Cultivator on ebay
"