Home | Manufacturer Directory | UPC Lookup | Wanted Manuals | Information Pages |
Register Login | Members Area |

Back To MTD Chipper Shredder       Model: 463 MTD Chipper Shredder
Regular Text Search or Search by Model Number

Register / log-in to add to your Hammerwall Collection.
Manual Location


Upload a pic of this item

Manuals For Same Model Number.
463 MTD Chipper Shredder...
463 MTD Yard Machines Chipper Shredder...
463 MTD Yard Machines Chipper Shredder...
463 MTD Chipper Shredder...

Other Model Numbers Referenced to The Same Manual.
462 MTD Chipper Shredder...
464 MTD Chipper Shredder...
465 MTD Chipper Shredder...

Other Items that are in the Same Category.
462 MTD Chipper Shredder...
463 MTD Chipper Shredder...
464 MTD Chipper Shredder...
465 MTD Chipper Shredder...
462 MTD Yard Machines Chipper Shredder...
463 MTD Yard Machines Chipper Shredder...
465 MTD Yard Machines Chipper Shredder...
462 MTD Yard Machines Chipper Shredder...
463 MTD Yard Machines Chipper Shredder...
464 MTD Yard Machines Chipper Shredder...

This is a partial text extraction from the pdf, to download the pdf, click the Manual tab. If you want to search this text, hold control and F, and type the word you are looking for.

Page: 1

Operator's Manual Chipper Shredder Model Series 462 thru 465 Model 465 Shown IMPORTANT : READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning : This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest - covered , brush - covered or grass - covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws ( if any ) . If a spark arrester is used , it should be maintained in effective working order by the operator . In the State of California the above is required by law ( Section 4442 of the California Public Resources Code ) . Other states may have similar laws . Federal laws apply on federal lands . A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department , P . O . Box 361131 Cleveland , Ohio 44 ! 36 - 0019 . MTD LLC , P . O . BOX 361131 CLEVELAND , OHIO 44136 - 0019 PRINTED IN U . S . A . FORM NO . 770 - 10048G 4 / 2004
Page: 2

TABLEOFCONTENTS Content Page Content Page Important Safe Operation Practices 3 Maintaining Your Chipper Shredder 9 Assembling Your Chipper Shredder 5 Trouble Shooting 12 7 Illustrated Parts List 14 Know Your Chipper Shredder Operating Your Chipper Shredder 8 Warranty 16 FINDINGMODELNUMBER This Operator's Manual is an important part of your new chipper shredder . It will help you assemble , prepare and maintain the unit for best performance . Please read and understand what it says . Before you start assembling your new equipment , please locate the model plate on the equipment and copy the information from it in the space provided below . A sample model plate is also given below . You can locate the model plate by standing behind the unit and looking down at the frame below the engine . This information will be necessary to use the manufacturer's web site and / or help from the Customer Support Department or an authorized service dealer . Copy the model number here : Copy the serial number here : CUSTOMERSUPPORT Please doNOTreturnthe unit to the retailer from where it waspurchased , withoutfirstcontactingCustomerSupport . If you have difficulty assembling this product or have any questions regarding the controls , operation or maintenance of this unit , you can seek help from the experts . Choose from the options below : Visit mtdproducts . com for many useful suggestions . Click on Customer Support button and you will get the four options reproduced here . Click on the appropriate button and help is immediately available . " _ = I . . . . Ioo ! i7 ! 7 ; i ' ; > l : ; o : 1 7 , i . $ . i , + : ; - . . . . . . . . / , x * ¢ > + / sOS @ cWd 1 _ ¢ ' 0J " . I > : O ! ! l : ) : l ; _ : sC _ ' / ¢ . . . . . , / . ' / If you prefer to reach a Customer Support Representative , please call 1 - 800 - 800 - 7310 . The engine manufacturer is responsible for all engine - related issues with regards to J - . / 4 3erformance , power - rating , specifications , warranty and service . Please refer to the engine En ine manufacturer's Owner's / Operator's Manual , packed separately with your unit , for more information .
Page: 3

SECTION1 : IMPORTANTSAFEOPERATIONPRACTICES WARNING : This symbol points out important safety instructions which , if not followed , could endanger the personal safety and / or property of yourself and others . Read and follow all instructions in this manual before attempting to operate this machine . Failure to comply with these instructions may result in personal injury . When you see this symbol - heed its warning . WARNING : The Engine Exhaust from this product contains chemicals known to the State of California to cause cancer , birth defects or other reproductive harm . DANGER : This machine was built to be operated according to the rules for safe operation in this manual . As with any type of power equipment , carelessness or error on the part of the operator can result in serious injury . This machine is capable of amputating hands and feet and throwing objects . Failure to observe the following safety instructions could result in serious injury or death . . Always wear safety glasses or safety goggles TRAINING during operation or while performing an adjustment 1 . Read , understand , and follow all instructions on the or repair , to protect eyes . Thrown objects which machine and in the manual ( s ) before attempting to ricochet can cause serious injury to the eyes . assemble and operate . Keep this manual in a safe . Wear sturdy , rough - soled work shoes and close - place for future and regular reference and for fitting slacks and shirts . Loose fitting clothes or ordering replacement parts . jewelry can be caught in movable parts . Never 2 . Be familiar with all controls and their proper operate this machine in bare feet or sandals . Wear operation . Know how to stop the machine and leather work gloves when feeding material in the disengage them quickly . chipper chute . 3 . Never allow children under 16 years old to operate . Before starting , check all bolts and screws for this machine . Children 16 years old and over proper tightness to be sure the machine is in safe should read and understand the operation working condition . Also , visually inspect machine instructions and safety rules in this manual and for any damage at frequent intervals . should be trained and supervised by a parent . . Maintain or replace safety and instructions labels , 4 . Never allow adults to operate this machine without as necessary . proper instruction . 6 . To avoid personal injury or property damage use 5 . Keep bystanders , helpers , pets , and children at extreme care in handling gasoline . Gasoline is least 75 feet from the machine while it is in extremely flammable and the vapors are explosive . operation . Stop machine if anyone enters the area . Serious personal injury can occur when gasoline is 6 . Never run an engine indoors or in a poorly spilled on yourself or your clothes which can ignite . ventilated area . Engine exhaust contains carbon Wash your skin and change clothes immediately . monoxide , an odorless and deadly gas . a . Use only an approved gasoline container . 7 . Do not put hands and feet near rotating parts or in b . Extinguish all cigarettes , cigars , pipes , and the feeding chambers and discharge opening . other sources of ignition . Contact with the rotating impeller can amputate c . Neverfuel machine indoors . fingers , hands , and feet . d . Never remove gas cap or add fuel while the 8 . Never attempt to unclog either the feed intake or engine is hot or running . discharge opening , remove or empty bag , or e . Allow engine to cool at least two minutes inspect and repair the machine while the engine is before refueling . running . Shut the engine offand wait until all f . Never over fill fuel tank . Fill tank to no more moving parts have come to a complete stop . than 1 / 2 inch below bottom of filler neck to Disconnect the spark plug wire and ground it provide space for fuel expansion . against the engine . g . Replace gasoline cap and tighten securely . h . If gasoline is spilled , wipe it off the engine PREPARATION and equipment . Move machine to another area . Wait 5 minutes before starting the 1 . Thoroughly inspect the area where the equipment is to be used . Remove all rocks , bottles , cans , or engine . i . Never store the machine or fuel container other foreign objects which could be picked up or inside where there is an open flame , spark , thrown and cause personal injury or damage to the machine . or pilot light ( e . g . furnace , water heater , space heater , clothes dryer , etc . )
Page: 4

j . Toreduceafirehazardk , eepmachinefree 10 . Keep all guards , deflectors and safety devices in ofgrass , leaveso , rotherdebrisbuild - up . place and operating properly . Cleanupoilorfuelspillageandremoveany 11 . Keep your face and body back and to the side of fuelsoakeddebris . the chipper chute while feeding material into the k . Allowmachinetocoolatleast5minutes machine to avoid accidental kickback injuries . beforestoring . 12 . Never operate this machine without good visibility or light . OPERATION 13 . Do not operate this machine on a paved , gravel or non - level surface . 1 . Do not put hands and feet near rotating parts or in 14 . Do not operate this machine while under the the feeding chambers and discharge opening . influence of alcohol or drugs . Contact with the rotating impeller can amputate 15 . Muffler and engine become hot and can cause a fingers , hands , and feet . burn . Do not touch . 2 . Before starting the machine , make sure the chipper 16 . Never pick up or carry machine while the engine is chute , feed intake , and cutting chamber are empty running . and free of all debris . 3 . Thoroughly inspect all material to be shredded and MAINTENANCEANDSTORAGE remove any metal , rocks , bottles , cans , or other foreign objects which could cause personal injury 1 . Never tamper with safety devices . Check their or damage to the machine . proper operation regularly . 4 . If it becomes necessary to push material through 2 . Check bolts and screws for proper tightness at the shredder hopper , use a small diameter stick . Do frequent intervals to keep the machine in safe not use your hands or feet . working condition . Also , visually inspect machine 5 . If the impeller strikes a foreign object or if your for any damage and repair , if needed . machine should start making an unusual noise or 3 . Before cleaning , repairing , or inspecting , stop the vibration , immediately shut the engine off . Allow the engine and make certain the impeller and all impeller to come to a complete stop . Disconnect moving parts have stopped . Disconnect the spark the spark plug wire , ground it against the engine plug wire and ground it against the engine to and perform the following steps : prevent unintended starting . a . Inspect fordamage . 4 . Do not change the engine governor settings or b . Repair or replace any damaged parts . overspeed the engine . The governor controls the c . Check for any loose parts and tighten to maximum safe operating speed of the engine . assure continued safe operation . 5 . Maintain or replace safety and instruction labels , as 6 . Do not allow an accumulation of processed necessary . material to build up in the discharge area . This can 6 . Follow this manual for safe loading , unloading , prevent proper discharge and result in kickback of transporting , and storage of this machine . 7 . Never store the machine or fuel container inside material through the feed opening . 7 . Do not attempt to shred or chip material larger than where there is an open flame , spark or pilot light specified on the machine or in this manual . such as a water heater , furnace , clothes dryer , etc . Personal injury or machine damage could result . 8 . Always refer to the operator's manual for proper 8 . Never attempt to unclog either the feed intake or instructions on off - season storage . discharge opening while the engine is running . 9 . If the fuel tank has to be drained , do this outdoors . Shut the engine off , wait until all moving parts have 10 . Observe proper disposal laws and regulations for stopped , disconnect the spark plug wire and gas , oil , etc . to protect the environment . ground it against the engine before clearing debris . 9 . Never operate without the shredder hopper , chipper chute , or chute deflector properly attached to the machine . Never empty or change discharge bag while the engine is running .
Page: 5

understand and follow the warnings and instructions in this manual and on the machine . , _ WARNING : - YOUR RESPONSIBILITY : Restrict the use of this power machine to persons who read , NOTE : Not all safety labels shown may apply to your chipper shredder . WA _ H / NQs [ _ : O NOT OPERATE THIS _ 4ACH _ NE { UNL _ s _ SS TNE CHUT b _ 2FLECTOR HAS B _ [ ' N PROPERLY IiNSTALLED AND IS SF ; CURED W / [ H " l HIF HAND KNOBS , SECTION2 : ASSEMBLINGYOURCHIPPERSHREDDER IMPORTANT : This unit is shipped without gasoline or oil in the engine . Be certain to service engine with gasoline and oil as instructed in the separate engine manual before operating your machine . NOTE : Reference to right or left hand side of the chipper shredder is observed from the operating position . = RemovingUnitFromCarton • Remove staples , break glue on top flaps , or cut tape at carton end and peel along top flap to open carton . • Remove loose parts if included with unit ( i . e . , operator's manual , etc . ) • Cut along corners , lay carton down flat , and remove packing material . • Roll or slide unit out of carton and check carton thoroughly for loose parts . Chipper _ LoosePartsInCarton ( SeeFigure1 ) Chute Hopper Assembly Chute Deflector Chipper Chute ( Select Models 462 thru 465 ) Bag ( Not Shown ) Tamper Plug ( If Equipped ) Safety Glasses ( Not Shown ) Figure 1
Page: 6

• Place second spacer over hex bolt inside other AttachingTheHopperAssembly ( A , M0de s ) hinge and secure with hex lock nut . • Remove six hex nuts and washers from the weld • Secure both sides of chute deflector to impeller studs on the impeller housing . Do not remove the housing using wing knobs previously removed . support plate . See Figure 2 . • Place hopper assembly into position in front of AttachingTheChipperChute impeller housing , aligning holes in hopper ( SelectModels462Thru465 ) assembly collar with weld studs . • Remove the three cupped washers and hex nuts Impeller Housing = . _ jlmpeller from weld studs around the opening on the side of Washer , _ racket the impeller housing . See Figure 4 . NOTE : Engine is not shown for clarity . Bracket • Remove the hex bolts , flat washers , and lock nuts from the two holes on the upper end of the support brace . Hopper Hex NuL _ _ _ _ _ _ _ e lease Chipper Weld Stud Support Weld Stud _ " - - . . _ Hop per Plate Assembly Figure 2 • Slide hopper assembly onto weld studs and replace Washer washers and hex nuts . Do not tighten completely . - Lock Nut • Lift hopper assembly up to impeller bracket assembly and slide the release rod out slightly to pport Brace hook the hopper bracket onto the rod . See Figure 2 . • Tighten the six hex nuts that secure hopper Hex Nut assembly to impeller housing and also tighten the Cuppeder hex nuts that secure hopper bracket to hopper Wash assembly . Figure 4 AttachingThe ChuteDeflector ( A , Models ) • Align the chipper chute over the weld studs , so the slot in the bottom of the chute is facing down . • Remove the wing knobs from each side of the lower • Secure chipper chute with the three cupped impeller housing . See Figure 3 . washers ( cupped side against the chipper chute ) Hex Lock Nut and hex nuts previously removed . Do not tighten the nuts at this time . s ! Bolt • The chipper shredder was shipped with one end of the support brace already secured to the lower frame . Loosen but do not remove the bolts securing the brace to the frame . • Align the holes in the chute with the holes in the top of the brace and attach brace to chipper chute with hardware previously removed . Tighten securely . • Tighten the bolts securing the support brace to the Wing Knob frame . • Tighten the three nuts on the weld studs holding the \ Chute Deflector chipper chute to the impeller housing . Figure 3 Remove the hex lock nut , spacers , and hex bolt from the top of the impeller housing . Align the chute deflector in position on the discharge opening and insert hex bolt with spacer through hinge on chute deflector ( spacers fit inside of hinges ) . See Figure 3 .
Page: 7

AttachingTheBag ( A , Modo s ) • To attach the bag , place the opening of the bag Clip completely over the chute deflector . • Pull on the drawstring until the bag is tight around chute deflector opening . • Clip the drawstring back on itself , tight against the chute deflector to secure into position . See Figure \ 5 . Chute Deflector C _ hihlppeBr ag Figure 5 SECTION3 : KNOWYOURCHIPPERSHREDDER Read this operator's manual and safety rules before HopperAssembly operating your chipper shredder . Compare the Allow leaves and small branches up to 1 / 2 diameter to illustrations in Figure 6 with your unit to familiarize be fed into the impeller for chipping and shredding . yourself with the location of various controls and Material can be raked into hopper assembly by adjustments . Save this manual for future reference . lowering the hopper assembly . See Figure 6 . StarterHandle Tamper Plug ( ifEquipped ) The starter handle is located on the engine . Pull the The tamper plug is designed to insert in the chipper starter handle to start engine . See Figure 6 . chute to push material toward the impeller . ReleaseRod See Figure 6 . The release rod is located on the impeller bracket EngineControls assembly and it is used to release or lock the hopper See the separate engine manual for the location and when raising or lowering . See Figure 6 . function of the controls on the engine . Chipper Chute Allow twigs and small branches up to 3 " in diameter on StoppingEngine select models 462 thru 465 and 2 " in diameter on model • Move throttle control lever to STOP or OFF 463 to be fed into the impeller for chipping . See Figure position . 6 . • Disconnect spark plug wire from spark plug and ground against the engine . Chipper Chute Hopper Assembly \ Release / / / Rod Ta _ mperPlug Mode1465Shown Figure 6
Page: 8

SECTION4 : OPERATINGYOURCHIPPERSHREDDER WARNING : The operation of any chipper StoppingEngine shredder can result in foreign objects • Move throttle control lever to STOP or OFF being thrown into the eyes , which can position . damage your eyes severely . Always wear • Disconnect spark plug wire from spark plug and the safety glasses provided with this unit ground against the engine . or eye shields before chipping or shred - ding and while performing any NOTE : See your engine manual packed with your unit adjustments or repairs . for more detailed instructions . GasAndOilFill - Up ToEmptyBag Service the engine with gasoline and oil as instructed in • Un - clip drawstring and loosen bag from chute the separate engine manual packed with your chipper deflector opening . shredder . Read instructions carefully . • Empty bag and reattach to the discharge chute opening . Pull on the drawstring until the bag is tight around the chute opening and clip the drawstring engine running or until the engine has WARNING : Never fill fuel tank indoors with tight against the chute deflector . been allowed to cool for at least two minutes after running . Lowering TheHopperAssembly • With one hand grasp the handle at the top of the Starting Engine hopper assembly and lift slightly . • Attach spark plug wire to spark plug . Make certain • With the other hand pull out on the release rod and the metal cap on the end of the spark plug is lower the hopper assembly to the ground . fastened securely over the metal tip on the spark See Figure 7 . plug . • Engines with choke lever : Move choke lever on engine to CHOKE position . ( A warm engine may not require choking ) . • Engines with primer : Prime engine as instructed in separate engine manual . • The throttle control lever is located on the engine . Move engine throttle control lever to FAST or START position . Release • Grasp starter handle and pull rope out slowly until Assembly Rod engine reaches start of compression cycle ( rope will pull slightly harder at this point ) . NOTE : A noise will be heard when finding the start of the compression cycle . This noise is caused by the fails Figure 7 and fingers , which are part of the shredding mecha - nism , and it should be expected until the impeller UsingTheChipperShredder reaches full speed . Yard waste such as leaves and pine needles can be • Pull rope with a rapid , continuous , full arm stroke . raked up through the hopper assembly for shredding . Keep a firm grip on starter handle . Let rope rewind After material has been shredded by the flail blades on slowly . the impeller assembly , it will be discharged out of • Repeat the previous steps until engine fires . When opening or into catcher bag . Do not attempt to shred or engine starts , move choke control ( if equipped ) chip any material other than vegetation found in a gradually to RUN position . normal yard ( i . e . branches , leaves , twigs , etc . ) Avoid fibrous plants such as tomato vines until they are thoroughly dried out . Twigs and small branches up to 3 " or in a poorly ventilated area . Engine _ , WARNING : Never run the engine indoors in diameter on select models 462 thru 465 and 2 " in exhaust contains carbon monoxide , an diameter on model 463 can be fed into the chipper odorless and deadly gas . chute . If equipped , use the tamper plug to push material into the chipper chute . See Figure 8 .
Page: 9

IMPORTANT : The flail screen is located inside the housing in the discharge area . tf the flail screen lChuteector becomes clogged , remove and clean as instructed in Def Chipper Chute SECTION 5 : MAINTAINING YOUR CHIPPER SHREDDER . For best performance , it is also important to keep the chipper blade sharp . opper Assembly Model 465 Shown Figure 8 SECTION5 : MAINTAININGYOURCHIPPERSHREDDER CustomerResponsibilities _ _ _ " o _ 2 " mot MAINTENANCE / _ ' _ _ ' _ S / / SERVICE SCHEDULE _ o _ , . aed . ae _ . _ e _ _ _ e . o _ o DATES Lubricate Release Bracket I - - y Lubricate Hopper Assembly : , / _ ? n O Lubricate Chute Deflector o . . Check Chipper Blade Check Oil ; _ : ; , ' Change Oil UJ Z Clean Air Filter Z LU Clean Engine Check Spark Plug Engine : Follow the separate engine manual packed nect spark plug , and ground against with you unit for lubrication instructions . , _ WARNING : Always stop engine , discon - engine before cleaning , lubricating or doing any kind of maintenance on your Maintenance machine . Engine Refer to the separate engine manual for all engine Lubrication maintenance instructions . Release Rod : Lubricate the release rod and spring with • Check engine oil level before each use as light oil once a season . instructed in the separate engine manual packed Hopper Assembly : Lubricate the pivot points on the with your unit . Read and follow instructions hopper assembly with light oil once a season . carefully . Chute Deflector : Lubricate the pivot points on the discharge chute with light oil once a season .
Page: 10

• Cleanair iocleanerevery25hoursundernormalursr SharpeningOrReplacingChipperBlades conditionosronceaseasonC . leaneveryfewhethea • Disconnect the spark plug wire and ground against underextremeldyustyconditionsT . oservicual the engine . cleanerr , efertotheseparateengineman • Remove the flail screen as instructed in the packedwithyourunit . previous section . • Thesparkplugshouldbecleanedandthegapr • Remove the chipper chute by removing three hex resetonceaseasonC . heckenginemanuaflo nuts and washers . correcpt lugtypeandgapspecifications . Select Models 462 thru 465 • Remove the chipper chute support brace from the RemovingTheFlailScreen frame by removing the hex bolts . Ifthe discharge area becomes clogged , remove the flail All Models screen and clean area as follows : • Rotate the impeller assembly by hand until you • Stop the engine and make certain the chipper locate one of the two chipper blades in the chipper shredder has come to a complete stop . chute opening . • Disconnect spark plug wire from spark plug and • Remove the blade by removing the internal hex ground against the engine . screws , lock washers , and hex nuts which secure it • Remove the bag and two wing knobs on each side to the impeller . Retain the hardware . See Figure 10 . of the chute deflector and lift the chute deflector up to keep it out of the way . See Figure 9 . Chute Lock Washer & Nut Rex Screw Chipper Blade pin Clips Wing Knobs Figure 10 NOTE : Use a 3 / 16 " hex key ( Allen ) wrench on the outside of the blade and a 1 / 2 " box ( or socket ) wrench Figure 9 on the inside of the impeller . Hold the Allen wrench • Remove the two hairpin clips from each clevis pin stationary and rotate the box ( or socket ) wrench to which extend through the housing and remove the loosen the nut . pins . See Figure 9 . • Install a replacement blade ( Part No . 781 - 0490 ) • Remove the flail screen from inside the housing with the hardware removed earlier or sharpen . and clean the screen by scraping or washing with water . IMPORTANT : When sharpening the blade , protect • Reinstall the screen , making certain to reassemble hands by using gloves . Follow the original angle of the flail screen with the curve side down . grind and make sure to remove an equal amount from • Reattach the chute deflector with the hardware each blade . previously removed and connect the bag to unit . • To replace the other blade , rotate the impeller to expose the second blade and repeat the steps above . NOTE : Make certain blades are reassembled with the sharp edge facing upward . Torque hardware to 250 - 300 in . Ibs . lO
Page: 11

NOTE : Use caution when removing the blade to avoid SharpeningOr ReplacingtheShredder contacting the weld studs on the housing . Blade IMPORTANT : When sharpening the blade , follow the original angle of grind as a guide . It is extremely important that each cutting edge receives an equal are sharp . Wear leather work gloves to , _ WARNING : The impeller's chipper blades amount of grinding to prevent an unbalanced blade . An protect your hands . unbalanced blade will cause excessive vibration when • Stop the engine and make certain that all moving rotating at high speeds and may cause damage to the parts have come to a complete stop . unit . The blade can be tested by balancing it on a • Disconnect the spark plug wire and ground against screwdriver or nail . Remove metal from the heavy side the engine . until it is balanced evenly . • Lower the hopper assembly and block up the IMPORTANT : When reassembling the blade , tighten housing . center bolt to between 550 and 700 in . - Ibs , and the two • Remove the six hex lock nuts and flat washers from out bolts to between 250 and 350 in . - Ibs . the weld studs on the flail housing . Retain the hardware . • Carefully separate the hopper assembly from the StoringYourChipperShredder impeller assembly and remove the support plate . • Clean the equipment thoroughly . • Wipe equipment with an oiled rag to prevent rust . NOTE : When reassembling the support plate , make • Refer to engine manual for correct engine storage certain the embossed tab faces inward towards the instructions impeller . • Store unit in a clean , dry area . Do not store next to • Remove the two wing knobs and cupped washers corrosive materials such as fertilizer . that secure the chute deflector and raise the chute . • Insert a 1 / 2 " or 3 / 4 " diameter pipe through the flail screen into the impeller to keep it from turning or remove the flail screen and insert a piece of wood into the chute opening . • Remove the two internal hex screws which secure the shredder blade to the impeller . See Figure 11 . Chute Deflector Shredder Blade Weld Stud Internal Hex Screw - - Hex Bolt . . . . Impeller j Figure 11 NOTE : Use a 3 / 16 " hex key ( Allen ) wrench on the outside of the shredder blade and a 1 / 2 " box ( or socket ) wrench on the inside of the shredder blade . Hold the Allen wrench stationary and rotate the box ( or socket ) wrench to loosen the nut . • Remove the hex bolt , lock washer , and flat washer to completely free the shredder blade . 11
Page: 12

SECTION6 : TROUBLESHOOTING Problem Cause Remedy Engine fails to start 1 . Spark plug wire disconnected . 1 . Connect wire to spark plug . 2 . Fuel tank empty or stale fuel . 2 . Fill tank with clean , fresh gasoline . 3 . Throttle control lever not in correct 3 . Move throttle lever to FAST position . starting position . ( If Equipped ) 4 . Choke not in CHOKE position . 4 . Move choke to CHOKE position . ( If Equipped ) 5 . Engine not primed . 5 . Prime engine . 6 . Blocked fuel line . 6 . Clean fuel line . 7 . Faulty spark plug . 7 . Clean , adjust gap , or replace . Engine runs erratic 1 . Spark plug wire loose . 1 . Connect and tighten spark plug wire . 2 . Unit running on CHOKE . 2 . Move choke lever to OFF position . ( If Equipped ) 3 . Blocked fuel line or stale fuel . . Clean fuel line ; fill tank with clean , fresh gasoline . . . Drain fuel tank . Refill with fresh fuel . Water or dirt in fuel system . 5 . 5 . Dirty air cleaner . Clean or replace air cleaner . 6 . 6 . See authorized service dealer . Carburetor out of adjustment . Too much vibration 1 . 1 . See authorized service dealer . Loose parts or damaged impeller . 1 . 1 . Engine overheats Engine oil level low . Fill crankcase with proper oil . 2 . 2 . Dirty air cleaner . Clean or replace air cleaner . 3 . 3 . See authorized service dealer . Carburetor not adjusted properly . 1 . 1 . Occasional skip ( hesitates ) Spark plug gap too close . Adjust gap to . 030 " . at high speed Unit does not discharge 1 . Chute deflector clogged . 1 . Stop engine immediately and disconnect spark plug wire . Clean flail screen and inside of discharge opening 2 . Foreign object lodged in impeller . 2 . Stop engine and disconnect spark plug wire . Remove lodged object . 3 . Lowengine RPM 3 . Always run engine at full throttle . Rate of discharge slows 1 . Lowengine RPM . 1 . Always run engine at full throttle . considerably or 2 . Chipper blade dull . 2 . Replace chipper blade or see your authorized service dealer . composition of discharged material changes NOTE : For repairs beyond the minor adjustments listed above , contact your nearest authorized service dealer . 12
Page: 13

NOTES 13
Page: 14

SECTION7 : PARTSLISTFORMODELSERIES462 THRU465 j4 17 \ 15 21 16 23 25 8 37 " 19 \ 36 20 27 48 I I 21 _ 69 26 29 ' 32 1 24 35 / 55 53 60 43 57 t Models 462 & 463 61 YrModels 464 & 465 56 \ 64 / ? ? ? Models 462 , 463,464C 6O Model 464G Only 65 Model 463 Only If Equipped 14
Page: 15

ModelSeries462 Thru465 Re _ Ref . Pa _ No . Part No . Part Description Part Description No . No . 1 . 728 - 0175 Pop Rivet 43 . 738 - 081311 Axle Assembly 2 . 731 - 1899 Chipper Shredder Chute 738 - 08141 . Axle Assembly 3 . 735 - 0249 Chute Flap 44 . 750 - 07861 . Spacer 4 . 781 - 0633 Chute Flap Strip 45 . 734 - 18451.1 . Wheel Complete 10.0 x 4.0 Gray 5 . 681 - 0095 ^ 46 . 726 - 0214 Chipper Chute Push Cap 6 . 681 - 0068A Chipper Chute Assembly 47 . 734 - 16001 . Wheel Complete 10.0 x 2.5 Plastic 7 . 710 - 0751 48 . 681 - 0004A Hex Cap Screw 1 / 4 - 20 x . 620 Outer Impeller Housing Assembly 8 . 712 - 3027 Hex Lock Nut 1 / 4 - 20 49 . 710 - 0825 Hex Cap Screw 114 - 20 x 3.75 9 . 710 - 0106 50 . 781 - 0515 Hex Cap Screw 1 / 4 - 20 x 1.25 Front Support Bracket 10 . 736 - 0173 Flat Washer . 28 ID x . 74 OD 51 . 781 - 0574 Shredder Plate 11 . 736 - 0242 Bell Washer . 340 ID x . 872 OD 52 . 681 - 0104 Rear Hopper Bracket Assembly 12 . 712 - 3010 Hex Nut 5 / 16 - 18 53 . 732 - 0306 Compression Spring 1.75 13 . 749 - 1004 54 . 736 - 0117 Flat Washer Support Brace 15 . 714 - 0149B Cotter Pin 55 . 714 - 0104 Cotter Pin 16 . 681 - 0048 56 . 736 - 0264 Flat Washer . 330 ID x . 630 OD Wing Knob 5 / 16 - 18 17 . 681 - 0094 57 . 710 - 0376 Chute Deflector Assembly Hex Cap Screw 5 / 16 - 18 x 1.0 18 . 711 - 0835 Clevis Pin 58 . 748 - 0453 Spacer , . 375 ID x 2.50 LG 19 . 781 - 0457 Shredder Screen 59 . 736 - 0362 Flat Washer . 320 ID x 1.25 OD 20 . 726 - 0211 U - Nut 5 / 16 - 18 60 . 712 - 0429 Hex Lock Nut 5 / 16 - 18 21 . 750 - 0793 61 . 731 - 1710 Spacer Hopper Collar 22 . 712 - 3027 Hex Lock Nut 1 / 4 - 20 62 . 681 - 0123 Front Hopper Bracket Assembly 23 . 712 - 3004A Hex Lock Nut 5 / 16 - 18 63 . 711 - 1128 Lock Rod 24 . 736 - 0119 Lock Washer 5 / 16 64 . 731 - 1707 Hopper Assembly 25 . 681 - 0184A Frame 65 . 710 - 3008 Hex Cap Screw 5 / 16 - 18 x . 75 Frame 67 . 731 - 1617 " 681 - 0183A $ Tamper Plug 26 . 710 - 0805 68 . 736 - 0451 Washer , . 320 ID x . 93 OD Hex Cap Screw 5 / 16 - 18 x 1.50 69 . 710 - 0502A 710 - 31805 Hex Cap Screw 5 / 16 - 18 x 1.75 Screw , 3 / 8 - 16 x 1.250 27 . 736 - 0170 Bell Washer 5 / 16 x 1.0 70 . 737 - 01951.1.1 . Elbow Fitting 28 . 681 - 0117 inner Impeller Housing Assembly 71 . 737 - 0298 : I : Oil Drain Pipe 29 . 710 - 3025 Hex Cap Screw 5 / 16 - 18 x . 625 72 . 737 - 0132 _ : Oil Drain End Cap 30 . 710 - 0157 73 . 736 - 0217 Lock Washer , 318 Hex Cap Screw 5 / 16 - 24 x . 75 31 . 781 - 0490 74 . 681 - 0133 " Chipper Blade Tongue Hitch Mount 32 . 710 - 1054 75 . 681 - 0134A * Base Hitch Mount Hex Cap Screw 5 / 16 - 24 x 1.0 33 . 681 - 0030 76 . 710 - 3001 " impeller Assembly Hex Cap Screw , 3t8 - 16 x . 88 Flat Washer 77 . 711 - 0299 " 34 . 736 - 03661.1 Clevis Pin , . 625 x 2.4 35 . 712 - 0411 Hex Lock Nut 5 / 16 - 24 78 . 711 - 0835 " Clevis Pin , . 50 x 4.62 36 . 781 - 0735 79 . 712 - 0798 " Retainer Pin Clip Hex Nut , 3 / 8 37 . 719 - 0329 Flail Blade 80 . 732 - 0194 " Spring Pin 38 . 711 - 0833B Clevis Pin 81 . 736 - 0133 " Flat Washer , . 411 x 1.25 x 1.0 39 . 715 - 0166 Pin 82 . 736 - 0169 " Lock Washer , 3 / 8 40 . 736 - 0247 Flat Washer 3 / 8 x 1.25 - - 72310400 Safety Glasses ( Not Shown ) 41 . 742 - 0571 Shredder Blade i 664 - 04022 Chipper Bag Ass'y ( Not Shown ) 42 . 710 - 1254 Hex Cap Screw 3 / 8 - 24 x 2.25 i 664 - 04023 _ Chipper Bag Ass'y ( Not Shown ) t Models 462 & 463 # Models 464 & 465 ? ? ? Models 462 , 463,464C Model 464G Only _ . Model 463 Only If Equipped 15
Page: 16

MANUFACTURER'S LIMITED WARRANTY FOR : ® The limited warranty set forth below is given by MTD LLC with e . MTD does not extend any warranty for products sold or respect to new merchandise purchased and used in the exported outside of the United States , its possessions United States , its possessions and territories . and territories , except those sold through MTD's authorized channels of export distribution . " MTD " warrants this product against defects in material and f . Replacement parts that are not genuine MTD parts . workmanship for a period of two ( 2 ) years commencing on the g . Transportation charges and service calls . date of original purchase and will , at its option , repair or replace , free of charge , any part found to be defective in No implied warranty , including any implied warranty of materials or workmanship . This limited warranty shall only merchantability of fitness for a particular purpose , apply if this product has been operated and maintained in applies after the applicable period of express written accordance with the Operator's Manual furnished with the warranty above as to the parts as identified . No other product , and has not been subject to misuse , abuse , express warranty , whether written or oral , except as commercial use , neglect , accident , improper maintenance , mentioned above , given by any person or entity , alteration , vandalism , theft , fire , water , or damage because of including a dealer or retailer , with respect to any product , other peril or natural disaster . Damage resulting from the shall bind MTD . During the period of the warranty , the installation or use of any part , accessory or attachment not exclusive remedy is repair or replacement of the product approved by MTD for use with the product ( s ) covered by this as set forth above . manual will void your warranty as to any resulting damage . The provisions as set forth in this warranty provide the Normal wear parts are warranted to be free from defects in sole and exclusive remedy arising from the sale . MTD material and workmanship for a period of thirty ( 30 ) days from shall not be liable for incidental or consequential loss or the date of purchase . Normal wear parts include , but are not damage including , without limitation , expenses incurred limited to items such as : batteries , belts , blades , blade for substitute or replacement lawn care services or for adapters , grass bags , rider deck wheels , seats , snow thrower rental expenses to temporarily replace a warranted skid shoes , shave plates , auger spiral rubber and tires . product . HOW TO OBTAIN SERVICE : Warranty service is available , Some states do not allow the exclusion or limitation of WITH PROOF OF PURCHASE , through your local authorized incidental or consequential damages , or limitations on how service dealer . To locate the dealer in your area , check your long an implied warranty lasts , so the above exclusions or Yellow Pages , or contact MTD LLC at P . O . Box 361131 , limitations may not apply to you . Cleveland , Ohio 44136 - 0019 , or call 1 - 800 - 800 - 7310 or 1 - In no event shall recovery of any kind be greater than the 330 - 220 - 4683 or log on to our Web site at amount of the purchase price of the product sold . Alteration www . mtdproducts . com . of safety features of the product shall void this warranty . This limited warranty does not provide coverage in the You assume the risk and liability for loss , damage , or injury to following cases : you and your property and / or to others and their property arising out of the misuse or inability to use the product . a . The engine or component parts thereof . These items may carry a separate manufacturer's warranty . Refer This limited warranty shall not extend to anyone other than the to applicable manufacturer's warranty for terms and original purchaser or to the person for whom it was purchased conditions . as a gift . b . Log splitter pumps , valves , and cylinders have a HOW STATE LAW RELATES TO THIS WARRANTY : This separate one year warranty . limited warranty gives you specific legal rights , and you may c . Routine maintenance items such as lubricants , filters , also have other rights which vary from state to state . blade sharpening , tune - ups , brake adjustments , clutch adjustments , deck adjustments , and normal IMPORTANT : Owner must present Original Proof of deterioration of the exterior finish due to use or Purchase to obtain warranty coverage . exposure . d . Service completed by someone other than an authorized service dealer . MTD LLC , P . O . BOX361131CLEVELAND , OHIO44136 - 0019 ; Phone : 1 - 800 - 800 - 7310,1 - 330 - 220 - 4683
Search in Chipper Shredder on ebay
"