|Home |||Register Login |||Wanted Manuals |||MarketPlace |||Members Area |||Manuals Manufacturer Directory |||UPC Lookup |||Information Pages |||Policy|
|Regular Text Search or Search by Model Number||
Manuals For Same Model Number.
E640F MTD Snow Thrower...
E640F MTD Yard Machinesd Snow Thrower...
Other Model Numbers Referenced to The Same Manual.
E600E MTD Yard Machines Snow Thrower...
E610E MTD Yard Machines Snow Thrower...
E660G MTD Yard Machines Snow Thrower...
E6C0F MTD Yard Machines Snow Thrower...
Other Items that are in the Same Category.
611 MTD Snow Thrower...
140 MTD Single Stage Snow Thrower...
150 MTD Single Stage Snow Thrower...
160 MTD Single Stage Snow Thrower...
380 MTD Two Stage Snow Thrower...
140 MTD Single Stage Snow Thrower...
150 MTD Single Stage Snow Thrower...
E150 MTD Single Stage Snow Thrower...
E162 MTD Single Stage Snow Thrower...
E172 MTD Single Stage Snow Thrower...
This is a partial text extraction from the pdf, to download the pdf, click the Manual tab. If you want to search this text, hold control and F, and type the word you are looking for.
OPERATOR'S MANUAL SNOW THROWER MODELS E600E , E610E E640F , E660G E6COF IMPORTANT : READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning : This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest - covered , brush - covered or grass - covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws ( if any ) . If a spark arrester is used , it should be maintained in effective working order by the operator . In the State of California the above is required by law ( Section 4442 of the California Public Resources Code ) . Other states may have similar laws . Federal laws apply on federal lands . A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department , P . O . Box 368022 Cleveland , Ohio 44136 - 9722 . MTD PRODUCTS INC . P . O . BOX 368022 CLEVELAND , OHIO 44136 - 9722 PRINTED IN U . S . A . FORM NO . 770 - 10002C 5 / 00
TABLEOFCONTENTS Content Page Important Safe Operation Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Loose Parts & Hardware Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Assembling Your Snow Thrower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Know Your Snow Thrower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Operating Your Snow Thrower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Making Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Maintaining Your Snow Thrower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Off - Season Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 FINDINGMODELNUMBER This Operator's Manual is an important part of your new snow thrower . It will help you assemble , prepare and maintain the unit for best performance . Please read and understand what it says . Before you start assembling your new equipment , please locate the model plate on the equipment and copy the information from it in the space provided below . The information on the Â¢ model plate is very important if you need help from our Customer Support Department or an authorized dealer . You can locate the model number by standing behind the unit in the operating position and looking down at the rear frame below the engine . A sample model plate is explained below . For future reference , please copy the model number and the serial number of the equipment in the space below . ( Model Number ) ( Serial Number ) Copy the model number here : Copy the serial number here : I JJ _ r'J _ ff MTDPRODUCTSINC I _ H _ CLEVELAND , OHIO 441 _ CALLINGCUSTOMERSUPPORT If you have difficulty assembling this product or have any questions regarding the controls , operation or maintenance of this unit , please call the Customer Support Department . Call 1 - ( 330 ) 220 - 4MTD ( 4683 ) or 1 - ( 800 ) - 800 - 7310 to reach a Customer Support representative . Please have your unit's model number and serial number ready when you call . See previous section to locate this information . You will be asked to enter the serial number in order to process your call .
SECTION1 : IMPORTANTSAFEOPERATIONPRACTICES This symbol points out important safety instructions which , if not followed , could endanger the personal safety and ! or property of yourself and others . Read and follow all instructions in this manual before , & attempting to operate this machine . Failure to comply with these instructions may result in personal injury . When you see this symbol - - heed its warning . WARNING : Engine Exhaust , some of its constituents , and certain vehicle components contain or emit chemicals known to State of California to cause cancer and birth defects or other reproductive harm . DANGER : This machine was built to be operated according to the rules for safe operation in this manual . As with any type of power equipment , carelessness or error on the part of the operator can , & result in serious injury . This machine is capable of amputating hands and feet and throwing objects . Failure to observe the following safety instructions could result in serious injury or death . 7 . Never attempt to make any adjustments while engine is Training running , except where specifically recommended in the 1 . Read , understand , and follow all instructions on the operator's manual . machine and in the manual ( s ) before attempting to 8 . Let engine and machine adjust to outdoor temperature assemble and operate . Keep this manual in a safe place before starting to clear snow . for future and regular reference and for ordering 9 . To avoid personal injury or property damage use extreme replacement parts . care in handling gasoline . Gasoline is extremely 2 . Be familiar with all controls and their proper operation . flammable and the vapors are explosive . Serious Know how to stop the machine and disengage them personal injury can occur when gasoline is spilled on quickly . yourself or your clothes which can ignite . Wash your skin 3 . Never allow children under 14 years old to operate this and change clothes immediately . machine . Children 14 years old and over should read and a . Use only an approved gasoline container . understand the operation instructions and safety rules in b . Extinguish all cigarettes , cigars , pipes and other this manual and should be trained and supervised by a sources of ignition . parent . c . Never fuel machine indoors . 4 . Never allow adults to operate this machine without d . Never remove gas cap or add fuel while the proper instruction . engine is hot or running . 5 . Thrown objects can cause serious personal injury . Plan e . Allow engine to cool at least two minutes before your snow throwing pattern to avoid discharge of material refueling . toward roads , bystanders and the like . f . Never over fill fuel tank . Fill tank to no more than 6 . Keep bystanders , helpers , pets and children at least 75 Â½ inch below bottom of filler neck to provide space feet from the machine while it is in operation . Stop for fuel expansion . machine if anyone enters the area . g . Replace gasoline cap and tighten securely . 7 . Exercise caution to avoid slipping or falling , especially h . If gasoline is spilled , wipe it off the engine and when operating in reverse . equipment . Move machine to another area . Wait 5 minutes before starting the engine . i . Never store the machine or fuel container inside Preparation where there is an open flame , spark or pilot light 1 . Thoroughly inspect the area where the equipment is to ( e . g . furnace , water heater , space heater , clothes be used . Remove all door mats , newspapers , sleds , dryer etc . ) . boards , wires and other foreign objects which could be j . Allow machine to cool at least 5 minutes before tripped over or thrown by the auger / impeller . storing . 2 . Always wear safety glasses or eye shields during operation and while performing an adjustment or repair to protect your eyes . Thrown objects which ricochet can Operation cause serious injury to the eyes . 1 . Do not put hands or feet near rotating parts , inthe auger / 3 . Do not operate without wearing adequate winter outer impeller housing or discharge chute . Contact with the garments . Do not wear jewelry , long scarves or other rotating parts can amputate hands and feet . loose clothing which could become entangled in moving 2 . The auger / impeller clutch lever is a safety device . Never parts . Wear footwear which will improve footing on bypass its operation . Doing so , makes the machine slippery surfaces . unsafe and may cause personal injury . 4 . Use a grounded three wire extension cord and receptacle 3 . The clutch levers must operate easily in both directions for all units with electric start engines . and automatically return to the disengaged position when 5 . Adjust collector housing height to clear gravel or crushed released . rock surfaces . 6 . Disengage all clutch levers before starting the engine .
4 . Neveorperatweithamissinogrdamageddischarge MaintenanceAndStorage chuteK . eepallsafetdyeviceisnplaceandworking . 1 . Never tamper with safety devices . Check their proper 5 . Neverrunanenginiendoorosrina poorly ventilated operation regularly . area . Engine exhaust contains carbon monoxide , an 2 . Disengage all clutch levers and stop engine . Wait until odorless and deadly gas . the auger / impeller come to a complete stop . Disconnect 6 . Do not operate machine while under the influence of the spark plug wire and ground against the engine to alcohol or drugs . prevent unintended starting before cleaning , repairing , or 7 . Muffler and engine become hot and can cause a burn . Do inspecting . not touch . 3 . Check bolts , and screws for proper tightness at frequent 8 . Exercise extreme caution when operating on or crossing intervals to keep the machine in safe working condition . gravel surfaces . Stay alert for hidden hazards or traffic . Also , visually inspect machine for any damage . 9 . Exercise caution when changing direction and while 4 . Do not change the engine governor setting or over - speed operating on slopes . the engine . The governor controls the maximum safe 10 . Plan your snow throwing pattern to avoid discharge operating speed of the engine . towards windows , walls , cars etc . To avoid property 5 . Snow thrower shave plates and skid shoes are subject to damage or personal injury caused by a ricochet . wear and damage . For your safety protection , frequently 11 . Never direct discharge at children , bystanders and pets check all components and replace with original or allow anyone in front of the machine . equipment manufacturer's ( O . EM . ) parts only . " Use of 12 . Do not overload machine capacity by attempting to clear parts which do not meet the original equipment snow at too fast of a rate . specifications may lead to improper performance and 13 . Never operate this machine without good visibility or compromise safety ! " light . Always be sure of your footing and keep a firm hold 6 . Check clutch controls periodically to verify they engage on the handles . Walk , never run . and disengage properly and adjust , if necessary . Refer to 14 . Disengage power to the auger / impeller when the adjustment section in this operator's manual for transporting or not in use . instructions . 15 . Never operate machine at high transport speeds on 7 . Maintain or replace safety and instruction labels , as slippery surfaces . Look down and behind and use care necessary . when in reverse . 8 . Observe proper disposal laws and regulations for gas , 16 . If the machine should start to vibrate abnormally , stop the oil , etc . to protect the environment . engine , disconnect the spark plug and ground it against 9 . Prior to storing , run machine a few minutes to clear snow the engine . Inspect thoroughly for damage . Repair any from machine and prevent freeze up of auger / impeller . damage before starting and operating . 10 . Never store the machine or fuel container inside where 17 . Disengage all clutch levers and stop engine before you there is an open flame , spark or pilot light such as a water leave the operating position ( behind the handles ) . Wait heater , furnace , clothes dryer etc . until the augedimpeller comes to a complete stop before 11 . Always refer to the operator's manual for proper unclogging the discharge chute , making any instructions on off - season storage . adjustments , or inspections . 18 . Never put your hand in the discharge or collector YourResponsibility : openings . Always use a clearing tool to unclog the Restrict the use of this power machine to persons who discharge opening . read , understand and follow the warnings and 19 . Use only attachments and accessories approved by the instructions in this manual and on the machine . The manufacturer ( e . g . wheel weights , tire chains , cabs etc . ) . safety labels are given below for your reference . 20 . If situations occur which are not covered in this manual , use care and good judgment . Contact your dealer or telephone 1 - 800 - 800 - 7310 for assistance and the name of your nearest servicing dealer . " LSEEPAWAYFROMROTATINIGMPELLER ANDAUGERC . OHTACWTITHiMF _ LERORET . AUGERCANAMPUTATHEANDASNDFE 2 . DISERGACGLEUTCLHEVERSST , OPENGINE , ANDREMAINREHINRHANDLEUSNTILALLRR MOVINGPARTSRAVE8TOPPERREFO UNCLOGGINOGRSERVICINMGACHINE . 3 . TOAVOIDTHROWROS , IECTISNJURIES , . NEVEDRIRECDTISCHARAGTESY $ 3 " SAENRSGN USEEXTRCAAI , rrlOWRHEROPERATINO GRAVESLURFACES , 4 . READOPERATOR'MSANUAL .
SECTION2 : LOOSEPARTS & HARDWARPEACK IMPORTANT : After assembly , service engine with ToolsRequiredForAssembly gasoline , and check oil level as instructed in the Pair of pliers separate engine manual packed with your unit . Two adjustable wrenches Unpacking Remove staples or break glue on the top flaps of ContentsIn CartonSeeFigure1 the carton . Remove any loose parts included with Right and Left Handles unit ( i . e . , Operator's Manual , etc ) . Handle Panel Assembly Cut along corners and lay end of carton down flat . Chute Assembly Remove packing material . Chute Directional Control Assembly Roll unit out of carton . Check carton thoroughly for Shift Rod loose parts before discarding . Hardware Pack Handle Panel Assembly Handles Chute Assembly Chute Directional _ _ _ _ _ - - _ / Shift Rod Control Assem T Figure 1
ContentsOfHardwarePack Lay out the hardware according to the illustration for identification purposes . Part numbers are shown in ) arentheses . ( Hardware pack may contain extra items which are not used on your unit . ) ATTACHING THE CHUTE ASSEMBLY A I ATTACHING THE HANDLES cl EL - - ' ] = r ' _ = ] C 3 = - - - Hex Bolts _ = = 5 / 16 - 18 x 1 - 3 / 4 " = ( 710 - 3180 ) Hex Bolts _ = = = 5 / 16 - 18 x 3 / 4 " ( 710 - 3008 ) Hex Bolts ( 710 - 3015 ) Handle Tabs ( 784 - 5599 ) Â© @ - oox - Lock Washers Chute Flange @ @ ( 716 - 0262 ) Keepers851A ) ( 731 - 0 Hex Lock Nuts 1 / 4 - 20 Thread ( 712 - 3027 ) 5 / 16 " I . D . Â© Â© Â© Â© c _ . ow _ ( 736 - 0242 ) D I ATTACHING THE CHUTE DIRECTIONAL _ _ CONTROL Hex Nuts 5 / 16 " Thread @ @ @ @ 3 / 8 " 1 . D . x 5 / 8 " O . D . O O Flat Washers ( 712 - 3010 ) ( 736 - 0185 ) B I ATTACHING THE SHIFT ROD Hex Nut AND CONTROL CABLES 5 / 16 " Thread @ @ ( 712 - 3010 ) Flat Washers 5 / 16 " LD . Ferrule Cupped Washers Hair Pin Clip ( 736 - 0242 ) ( 71 % 0677 ) 3 / 8 " LD . x 5 / 8 " O . D . Hair Pin Clip ( 736 - 0275 ) ( 714 - 0104 ) ( 714 - 0104 ) E _ AUGER SHEAR BOLTS ( SPARES ) Hex Lock Nuts _ Shear Bolts ( 710 - 0890A ) @ @ 5 / 16 " Thread ( 712.0429 ) NOTE : The augers are secured to the spiral shaft with two shear bolts and hex lock nuts . If you hit a hard foreign object or an ice jam , the snow thrower is designed so that the bolts may shear . Two replacement shear bolts and nuts are provided for your convenience . Store in a safe place until needed . IMPORTANT : NEVER replace the auger shear bolts with standard hex bolts . Any damage to the auger gearbox or other components as a result of doing so wilt NOT be covered by your snow thrower's warranty . 6
SECTION3 : ASSEMBLINGYOURSNOWTHROWER wire and ground it against the engine to WARNING : Disconnect the spark plug Cupped prevent unintended starting . NOTE : All references to right or left side of the snow thrower are determined from behind the unit in the operating position . AttachingTheHandleAssembly ( HardwareA ) Place right handle in position against the snow Hex Nuts thrower so the flat side of the handle is against the Carriag _ Bolts snow thrower . Secure bottom hole in handle to snow thrower using 3 / 4 " hex bolt and lock washer . Figure 3 Do not tighten at this time . See Figure 2 . Place handle tab over the upper hole in handle so AttachingTheControlCables the curve in the handle tab matches the curve in the handle . Secure to the snow thrower using ( HardwareB ) 1 - 3 / 4 " hex bolt and lock washer . Do not tighten at The " Z " end of the cables are hooked into the controls this time . on each handle . See Figure 4 . Attach the left handle in the same manner . Do not Thread the hex lock nuts all the way up the tighten at this time . threaded portion of the " Z " ends of the cables . Make certain all cables are in the grooves of the cable roller guides . The two roller guides are I 3 / 4 " Hex located in the lower rear of the unit , one on each side . See Figure 2 . Thread the cable onto the threaded portion of the " Z " end until there is no slack in the cable , but the cable is NOT tight . Do not overtighten cable . WARNING : If cable is tightened so there is tension on the cable with the clutch grip released , the safety features of the snow Guide thrower may be overridden . Washers Bolt When correct adjustment is reached , tighten the hex lock nut against the bottom portion of the cable Figure 2 to lock it in position . Place the handle panel in position between the handles . To hold the handle panel in place , depress both controls against the handles . While continuing to hold the right control , release the left control ( the auger control lock will keep left control engaged ) . See Figure 3 . Fasten right side of the handle panel by inserting two carriage bolts through handle and handle panel ( bolts must go through both the plastic and metal parts of the handle panel ) . Secure with End cupped washers ( cupped side against handle panel ) and hex nuts . Secure the left side of the handle panel in the ex Lock same manner . Nut Tighten the four hex bolts used to attach the Figure 4 bottom of the handles to the snow thrower frame .
AttachingTheChuteAssembly ( HardwareC ) Place chute assembly over chute opening , with the Carriage opening in the chute assembly facing the front of the unit . Place chute flange keepers beneath lip of chute assembly , with the fiat side down . Secure with hex bolts and hex lock nuts . Tighten with two adjustable wrenches . Do not overtighten . See Figure 5 . Hex Lock Nuts Bracket Figure 7 Place one flat washer on the end of the chute Chute directional control , then insert the end of the control into the hole in the plastic bushing in the lower chute bracket . Place another flat washer on the end of the chute directional control , and insert hairpin clip into hole in the end of control . See Figure 8 . Hairpin L / ( _ irne _ : tirnoa _ l Figure 5 AttachingTheChuteDirectionaCl ontrol Chute ( HardwareD ) Thread one hex nut about halfway onto eye bolt on Flat _ ' _ the chute directional control . Insert eye bolt _ Lower Chute through the hole provided in the left handle . See Bracket Washers Figure 6 . Secure with cupped washer ( cupped side against the handle ) and other hex nut . Do not tighten until Figure 8 after attaching the other end of the chute Adjust the chute bracket so that the spiral on the directional control . chute directional control fully engages the teeth on the chute assembly . Tighten the nuts on the lower Hex Nut chute bracket securely . Tighten the hex nut on the Cupped eye bolt on the chute directional control . IMPORTANT : Attach the shift rod and clutch cables as follows . THEN CHECK THE ADJUSTMENTS AS INSTRUCTED , AND MAKE ANY FINAL ADJUSTMENTS NECESSARY BEFORE OPERATING YOUR SNOW THROWER . Failure to follow the instructions may cause damage to the snow e Bolt thrower . AttachingTheShiftRod ( HardwareB ) Place the shift lever ( on the handle panel ) in the Figure 6 sixth ( 6 ) speed position ( all the way forward ) . To align the spiral on the chute directional control , Place the bent end of the shift rod into the hole in it may be necessary to loosen the carriage bolts the shift arm assembly . Secure with flat washer and hex lock nuts which secure the lower chute and hairpin clip . See Figure 9 . bracket to the extension on the left side of the Start threading the ferrule onto the other end of the chute assembly . See Figure 7 . shift rod . Push down on the shift rod ( and shift arm assembly ) as far as it wilt go .
Threadtheferruleontotheshiftroduntiltheferrule aulinesupwiththeupperholeintheshiftleverleintoesher ( beneaththehandlepanel ) I . wnserttheferreftsid htheupperholeintheshiftleverfromthelflat whenadjustmenistcorrectS . ecurewit andhairpinclip . Makecertaintocheckforcorrecat rdjustmenotftheshifte rodasinstructedintheFinalAdjustmenstectionbefo operatingthesnowthrower . Nut Clip Make Sure Shift Rod Figure 10 TractionControlAndShift Lever Shift Arm Assembl Adjustment To check the adjustment of the traction control and shift lever , move the shift lever all the way forward to sixth ( 6 ) position . With the traction control released , push the snow thrower forward . The unit should move forward Clip freely . Then engage the traction control grip . The wheels should stop turning . Figure 9 Now release the traction control grip , and push the unit again . Move the shift lever back to the fast reverse FinalAdjustments position , then all the way forward again . There should be no resistance in the shift lever , and the wheels AugerControlAdjustment should keep turning . To check the adjustment of the auger control , push If you have resistance when moving the shift lever or forward on the left hand control , depressing the rubber the wheels stop when they should not , loosen the jam bumper on end of control . There should be slack in the nut on the traction control cable and unthread the cable cable . Release the control . The cable should be one turn . If the wheels do not stop when you engage the straight . Make certain you can depress the auger traction control gdp , loosen the jam nut on the traction control against the left handle completely . control cable and thread the cable in one turn . Recheck the adjustment and repeat as necessary . Tighten the If necessary , loosen the hex jam nut and thread the jam nut to secure the cable when correct adjustment is cable in ( for less slack ) or out ( for more slack ) as reached . necessary . Recheck the adjustment . Tighten the jam nut against the cable when correct adjustment is AdjustingTheSkidShoes reached . SeeFigure 10 . The space between the shave plate and the ground can be adjusted . For close snow removal , place skid shoes in the low position . Use middle or high position when area to be cleared is uneven . See Figure 11 . Adjust skid shoes by loosening the four hex nuts and carriage bolts and moving skid shoes to desired position . Make certain the entire bottom surface of skid shoe is against the ground to avoid uneven wear on the skid shoes . Retighten nuts and bolts securely .
It is not recommended that you operate this snow thrower on gravel as loose gravel can be easily picked up and thrown by the auger causing an injury or damage to the snow thrower . TirePressure ( PneumatiTcires ) The tires are over - inflated for shipping purposes . Check tire pressure and reduce to 15 to 20 psi . NOTE : If the tire pressure is not equal in both tires , Carriagd the unit may pull to one side or the other . Bolts kid . . . . . . . . . . _ _ , _ Shoes Figure 11 SECTION4 : KNOWYOURSNOWTHROWER Shift Lever WARNING : Be familiar with all controls The shift lever is located in the center of the handle and their proper operation . Know how to stop the machine and disengage them panel . The shift lever may be moved into one of eight quickly . positions . Run engine with throttle in the fast position . Use the shift lever to determine ground speed . See Figure 12 . OperatinCgontrols Forward - There are six speeds . Position number one Auger Traction / Auger ( 1 ) is the slowest . Position number six ( 6 ) is the Control Control Lock fastest . Reverse - There are two reverse ( R ) speeds R1 and R2 . The " R2 " closest to the operator ( ait the way back ) is the faster of the two . AugerControl The auger control is located on the left handle . Squeeze the control to engage the augers . Release to stop the snow throwing action . ( Traction control must also be released . ) See Figure 12 . Traction / AugerControlLock The traction control is located on the right handle . Squeeze the control to engage the wheel drive . Release to stop . Directional Control This same control also locks the auger control so you can turn the chute directional control without â¢ AUGERCONTROL 61 interrupting the snow throwing process . If the auger control is engaged with the traction control engaged , 4g the operator can release the auger control ( on the left handle ) and the augers will remain engaged . Release 2Q the traction control to stop both the augers and wheel F 11 drive ( auger control must also be released ) . CHUTE OIR _ CTIONAL CONTROL See Figure 12 . ChuteDirectionalControl R21m The chute directional control is located on left hand CLOC _ SE TOD _ SC _ AR _ ELEFT _ OU _ TERCLOCK _ SE TOD _ SC _ RGER _ G _ T side of the snow thrower . See Figure 12 . To change the direction in which snow is thrown , turn Figure 12 chute directional control as follows : 10
Crankclockwisetodischargteotheleft . Crankcounterclockwitsoedischargteotheright . ThrottleControl Choke Primer The throttle control is located on the engine . It regulates the speed of the engine . See Figure 14 . SafetyIgnitionSwitch The ignition key must be inserted in the switch before the unit wiltstart . Remove the ignition key when snow thrower is not in use . Fuel Shut - off Valve ( If Equipped ) The fuel shut - off valve , C , o , ed located under fuel tank , Handle controls fuel flow from Ig Throttle Open _ L _ J I Control Key tank . See Figure 13 . I Figure 13 Figure 14 SECTION5 : OPERATINGYOURSNOWTHROWER BeforeStarting Metal on all instructions and warnings on the machine Plug Wire , _ WARNING : Read , understand , and follow and in this manual before operating . . , _ Rubber Boot The spark plug wire was disconnected for safety . Attach spark plug wire to spark plug before Figure 15 starting . Make certain the fuel shut - off valve is inthe OPEN GasAndOilFill - up ( vertical ) position . Make certain the auger and traction controls are in WARNING : Use extreme care when the disengaged ( released ) position . handling gasoline . Gasoline is extremely Move throttle control up to FAST position . Insert flammable and the vapors are explosive . ignition key into slot . Be certain it snaps into place . Never fuel machine indoor or while the Do not turn key . See Figure 16 . engine is hot or running . Extinguish NOTE : Engine will not start unless ignition key is cigarettes , cigars , pipes and other sources inserted into ignition slot in carburetor cover . Do not of ignition . turn ignition key . A plastic cup was provided inside the fuel fill opening on the fuel tank . Remove and discard this RecoilStarter : cup before filling up the tank . Use the separate Rotate choke knob to FULL choke position ( cold fuel tank cap to close after fill - up . engine start ) . If engine is warm , place choke in OFF position StartingEngine instead of FULL . Attach spark plug wire to spark plug . Make certain Push primer button three or four times for cold the metal loop on end of the spark plug wire engine start . ( inside the boot ) is fastened securely over the If engine is warm , push primer button once only . metal tip on the spark plug . See Figure 15 . NOTE : Always cover vent hole in primer button when pushing . Additional priming may be necessary for first start if temperature is below 15 degrees Fahrenheit . 11
Grasp starter handle and pull rope out slowly , Connect power cord to switch box on engine . until it pulis slightly harder . Let rope rewind Plug the other end of power cord into a three - slowly . hole , grounded 12 - volt AC receptacle . Pull starter handle rapidly . Do not allow handle to Push starter button to crank engine . See Figure snap back . Allow it to rewind slowly while keeping 16 . As you crank the engine , move choke knob to a firm hold on the starter handle . FULL choke position . ( cold engine start ) Repeat step above until engine starts . When engine starts , release starter button , and As engine warms up and begins to operate move choke gradually to OFF . If engine falters , evenly , rotate choke knob slowly to OFF position . move choke immediately to FULL and then If engine falters , return to FULL choke , then gradually to OFF . slowly move to OFF position . StoppingEngine Starter Button Switch Box Run engine for a few minutes before stopping to Spark help dry off any moisture on the engine . Plug To help prevent possible freeze up of starter , proceed as follows . Electric Starter : Connect power cord to switch box on engine , then to 120 volt AC receptacle . With the engine running , pushstarter button and spin the starter for several seconds . The unusual sound made by spinning the starter will not harm engine or starter . Disconnect the power cord from receptacle first , and then from switch box . Recoil Starter : With engine running , pull starter Rope Starter Handle rope with a rapid , continuous full arm stroke two or three times . Pulling the starter rope will Key Throttle producea loud clattering sound , which is not Control harmful to the engine or starter . To stop engine , move throttle control to " stop " or Figure 16 " off " position . Remove the ignition key . Do not turn key . ElectricStarter : ( If Equipped ) Disconnect the spark plug wire from the spark plug to prevent accidental starting while WARNING : The electric starter is equipment is unattended . equipped with a three - wire power cord and plug , and is designed to operate on 120 volt NOTE : Do not lose the ignition key . Keep it in a safe AC household current . It must be properly place . Engine will not start without the ignition key . grounded at all times to avoid the possibility Wipe ait snow and moisture from the carburetor of electric shock which may cause injury to cover in the area of the control levers . Also , move the operator . control levers back and forth several times . Follow all instructions carefully . Determine that your house wiring is a three wire grounded system . Ask a ToEngageDrive licensed electrician if you are not certain . If your With the engine running near top speed , move house wiring system is not a three - wire grounded shift lever into one of the five FORWARD system , do not use this electric starter under any positions or two REVERSE positions . Select a conditions . If your system is grounded and a three - speed appropriate for the snow conditions that hole receptacle is not available at the pointyour exist . Use the slower speeds until you are familiar starter will normally be used , one should be installed with the operation of the snow thrower . by a licensed electrician . Squeeze the auger control and the augers will When connecting the power cord , always connect turn . Release it and the augers will stop . cord to starter on engine first , then plug the other end Squeeze the traction control and the snow into a three - hole grounded receptacle . thrower will move . Release it and drive motion will When disconnecting the power cord , always unplug stop . the end from the three - hole grounded receptacle first . NEVER move shift lever without releasing traction control . Rotate choke knob to OFF position . Do not prime engine . 12
ToEngageAugers surrounding areas become hot and can _ lb WARNING : Muffler , engine and To engage the augers and start the snow throwing cause a burn . Do not touch . action , squeeze the auger control against the left handle . Release to stop the augers . For most efficient snow removal , remove snow immediately after it falls . Discharge snow downwind whenever possible . TireChains ( OptionalEquipment ) Slightly overlap each previous path . If your unit is not equipped with tire chains , you may Set the skid shoes 1 / 4 " below the scraper bar for purchase them . Tire chains should be used whenever normal usage . The skid shoes may be adjusted extra traction is needed . upward for hard - packed snow . Adjust downward when using on gravel or crushed rock . OperatinTgips Be certain to follow the precautions listed under STOPPING ENGINE to prevent possible freeze - NOTE : Allow the engine to warm up for a few up . minutes as the engine will not develop full power until Clean the snow thrower thoroughly after each it reaches operating temperature . use . SECTION6 : MAKINGADJUSTMENTS WARNING : NEVER attempt to make ShiftRodAdjustment any adjustments while the engine is To adjust the shift rod , separate the shift rod and running , except where specified in the ferrule from the shift lever by removing the hairpin clip operator's manual . and flat washer from the ferrule underneath the handle panel . Refer to Figure 9 . Adjust as specified in ChuteAssemblyAdjustment the Assembly Instructions . The distance snow is thrown can be adjusted by adjusting the angle of the chute assembly . The CarburetorAdjustment sharper the angle , the shorter the distance snow is thrown . See Figure 17 . WARNING : If any adjustments need to be made to the engine while the engine is To adjust chute assembly , loosen the hand knob . running ( e . g . carburetor ) , keep clear of all Pivot the top of the chute assembly to position moving parts . Be careful of muffler , engine desired . Retighten the hand knob . and other surrounding heated surfaces . Minor carburetor adjustment may be required to compensate for differences in fuel , temperature , altitude and load . Refer to the separate engine manual packed with your unit for carburetor adjustment information . SkidShoeAdjustment The space between the shave plate and the ground can be adjusted . Refer to the ASSEMBLY section . TractionControlAdjustment Refer to the FINAL ADJUSTMENT section of the Figure 17 Assembly Instructions to adjust the traction control . If you are uncertain that you have reached the correct adjustment , the adjustment can be physically AugerClutchAdjustment checked as follows . To adjust the auger control , refer to FINAL With the snow thrower tipped forward ( be certain to ADJUSTMENT section of Assembly Instructions . drain the oil and gasoline or drain the oil and place plastic film under the gas cap if the snow thrower has already been operated ) , remove the frame cover 13
underneatthhesnowthrowebr yremovingsixself - NOTE : If you placed plastic under the gas cap , be tappingscrews . certain to remove it . Withthetractioncontrorleleasedth , eremustbe clearancebetweenthefrictionwheeal ndthedrive DriveWheels plateinallpositionsoftheshiftleverW . iththetraction The wheels may be adjusted for two different controel ngagedt , hefrictionwheeml ustcontactthe methods of operation . The adjustment is made by driveplate . SeeFigure18 . placing the klick pins in one of two different holes on the right side of the unit . See Figure 19 . One Wheel Driving - Place ktick pin in the outside Friction axle hole on the right side . This position gives power drive to the left wheel only , making the unit WheeIl LI easier to maneuver . Both Wheels Driving - Rotate wheel assembly to align hole in hub with inner hole on axle shaft . _ _ PI _ / f _ Gear Shaft I Insert klick pin in hole . Outer axle shaft hole should be visible . This position is good for heavy snow as there is power to both wheels . Hub Hole Figure 18 If adjustment is necessary , loosen the hex jam nut on Pin Inxle the traction control cable and thread the cable inor Outside A Hole out as necessary . Tighten the hex jam nut to secure the cable when correct adjustment is reached . Figure 19 Reassemble the frame cover . SECTION7 : MAINTAININGYOURSNOWTHROWER or inspecting , disengage all clutch glevers , _ lb WARNING : Before servicing , repairin _ / Klick Pin and stop engine . Wait until all moving parts have come to a complete stop . Disconnect spark plug wire and ground it against the engine to prevent unintended starting . Lubrication Axle ChuteDirectionaCl ontrol The worm gear on the chute directional control should Figure 20 be greased with multipurpose automotive grease . AugerShaft Wheels At least once a season , remove shear bolts on auger Oil or spray lubricant into bearings at least once a shaft . Oil or spray lubricant inside shaft . Also lubricate season . Pull the klick pins and remove wheels , clean the auger bearings at least once a season . See and coat axles with a multipurpose automotive Figure 21 . grease . See Figure 20 . 14
DriveAndShiftingMechanism Shear Bolts Remove rear cover . Oil any chains , sprockets , gears , bearings , shafts , and shifting mechanism at least once a season . Use engine oil or a spray lubricant . Avoid getting oil on rubber friction wheel and aluminum drive plate . Refer to Figure 18 . GearCase The worm gear case has been filled with grease at the factory . If disassembled for repairs , lubricate with 2 ounces of shell grease , part no . 737 - 0168 . IMPORTANT : Do not overfill the gear case . Damage to Bearings Bearings the seals could result . Be sure the vent plug is free of grease in order to relieve pressure . Figure 21 GearShaft Engine Refer to separate engine manual for engine Lubricate the gear shaft with a good all - weather multi - maintenance procedures . purpose light grease at least once a season or after every 25 hours of operation . Refer to Figure 18 . in separate engine manual for draining oil , _ , WARNING : When following instructions IMPORTANT : Keep all grease and oil off of the friction be sure to protect frame to avoid oil dripping wheel and drive plate . onto transmission parts . CleanEquipment Be certain to follow the precautions listed under TO STOP ENGINE to prevent possible freeze - up . SECTION8 : SERVICE the skid shoes are adjusted to be level . Augers To remove shave plate , remove the carriage bolts , The augers are secured to the spiral shaft with two bell washers and hex nuts which attach itto the snow shear bolts and hex lock nuts . See Figure 21 . If you thrower housing . Reassemble new shave plate , hit a foreign object or ice jam , the snow thrower is making sure heads of the carriage bolts are to the designed so that the hex bolts will shear . inside of the housing . Tighten securely . If the augers will not turn , check to see if the bolts have sheared . Two replacement shear bolts and hex Engine lock nuts have been provided with the snow thrower . Refer to separate engine manual for all engine For future use , order part number 710 - 0890A ( shear service procedures . bolt 5 / 16 - 18 x 1.5 " ) and 712 - 0429 ( hex lock nut 5 / 16 - 18 ) . BeltRemovaAl ndReplacement ShavePlateAndSkidShoes The shave plate and skid shoes on the bottom of the _ , WwiAreRfNroINmGt : he sDpiasrckonpnluegct anthdegsropuanrkd . plug snow thrower are subject to wear . They should be checked periodically and replaced when necessary . AugerBelts To remove skid shoes , remove the four carriage bolts , bell washers and hex nuts which attach them to NOTE : It is necessary to remove both belts in order the snow thrower . Reassemble new skid shoes with to change either one . If changing just one belt , be the four carriage bolts , bell washers ( cupped side certain to check the condition of the other belt ( model goes against skid shoes ) and hex nuts . Make certain 15
600 / 610E has only one auger belt ) . Remove the plastic belt cover on the front of the Friction engine by removing the two self - tapping screws . Wheel See Figure 22 . Belt / Cover Support Rear Auger Belt - - Front Auger Figure 22 Pulley Auger Auger Bracket Drain the gasoline from the snow thrower , or place Pulley Idler Housing Spring Spring a piece of plastic under the gas cap . Tip the snow thrower up and forward so that it rests Figure 24 on the housing . Liftthe rear auger belt from the auger pulley , and Remove six self - tapping screws from the frame slip belt between the support bracket and the auger cover underneath the snow thrower . pulley . See Figure 24 . Repeat this step for front Roll the front and rear auger belts offthe engine auger belt ( except models 600 / 610E ) . pulley . See Figure 23 . Replace both auger drive belts by following instructions in reverse order . Rear Auger t _ _ ' _ - - _ Drive ] Belt \ , - - _ ( f = = _ Belt Engine I DriveBelt / Pu . ey I Follow steps 1 through 4 of previous instructions . _ / ( / _ ' _ _ ; ; ; _ - - _ Front AugerI Pull idler pulley up , and lift belt off engine pulley Idler _ l ' _ * J _ ' , , _ _ _ / / Belt I and friction wheel disc . See Figure 23 . Pulley \ _ f % , . ' _ _ JF I Back out the stop bolt untilthe support bracket rests on the auger pulley . See Figure 25 . Slip belt between friction wheel and friction wheel disc . Remove and replace belt . Reassemble following the instructions in reverse order . NOTE : The support bracket must rest on the stop bolt / Engine Pulley \ K . _ I after the new belt has been assembled . See Figure 25 . / Pulley \ _ . L _ _ - J Figure 23 Unhook the idler spring from the hex bolt on the auger housing . See Figure 24 . Back out the stop bolt to allow the belts to slip between the bolt and auger pulley . See Figure 25 . NOTE : It may be necessary to loosen the six hex nuts that fasten the frame to the auger housing to aid in belt removal . 16
Remove six self - tapping screws from the frame Friction cover underneath the snow thrower . I Remove the ktick pins which secure the wheels , and remove the wheels from the axle . Belt Using a wrench to hold the shaft , loosen , but do not completely remove , the hex nut and bell washer on Bolt left end of gear shaft . See Figure 26 . Lightly tap the hex nut to dislodge the ball bearing from the right side of frame . Remove the hex nut and bell washer from left end of shaft . Slide the gear shaft to the right and slide the friction wheel assembly from the shaft . Remove the six screws from the friction wheel Support Bracket assembly ( three from each side ) . Remove the friction wheel rubber from between the friction Figure 25 wheel plate . See Figure 27 . Friction Wheel ChangingFrictionWheelRubber Plates The rubber on the friction wheel is subject to wear and should be checked after 25 hours of operation , and Bearing periodicallythereafter . Replace the friction wheel rubber if any signs of wear or cracking are found . Drain the gasoline from the snow thrower , or place a piece of plastic under the gas cap . Tip the snow thrower up and forward , so that it Friction Wheel rests on the housing . See Figure 26 . Rubber Hub Figure 27 Reassemble new friction wheel rubber to the friction wheel assembly , tightening the six screws in rotation and with equal force . Position the friction wheel assembly up onto the pin of the shift rod assembly , and slide the shaft Hex Nut and through the assembly . Reassemble in reverse order . Figure 26 SECTION9 : OFF - SEASONSTORAGE Remove all dirt from exterior of engine and WARNING : Never store engine with fuel in equipment . tank indoors or in enclosed , poorly ventilated Follow lubrication recommendations in SECTION areas where fuel fumes may reach an open 7 : MAINTAINING YOUR SNOW THROWER . flame , spark or pilot light as on a furnace , water heater , clothes dryer , or other gas NOTE : When storing any type of power equipment in appliance . an poorly ventilated or metal storage shed , care should If unit is to be stored over 30 days , prepare the be taken to rustproof the equipment , especially springs , engine for storage as instructed in the separate cables and all moving parts . engine operator's manual included with your unit . 17
SECTION10 : TROUBLESHOOTINGGUIDE Corrective Action Trouble Possible Cause ( s ) Engine fails to start Fuel tank empty , or stale fuel . Fill tank with clean , fresh gasoline . Fuel may not last over thirty days unless a fuel stabilizer is used . Blocked fuel line . Clean fuel line . Choke not in ON position Move switch to ON position Faulty spark plug . Clean , adjust gap or replace . Key not in switch on engine . Insert key . Spark plug wire Connect spark plug wire . disconnected . Primer button not depressed . Refer to the engine manual packed with your unit . Fuel shut - off valve closed Open fuel shut - off valve . ( if so equipped ) . Engine runs erratic Unit running on CHOKE . Move choke lever to OFF position . Blocked fuel line or stale fuel . Clean fuel line ; fill tank with clean fresh gasoline . Fuel may not last over thirty days unless a fuel stabilizer is used . Water or dirt in fuel system . Drain fuel tank . Refill with fresh fuel . Carburetor out of adjustment . Refer to the engine manual packed with your unit or have carburetor adjusted by an authorized service dealer . Loss of power Spark plug wire loose . Connect and tighten spark plug wire . Gas cap vent hole plugged . Remove ice and snow from cap . Be certain vent hole is clear . Exhaust port plugged . Clean - see Maintenance section of engine manual . Engine overheats Carburetor not adjusted Refer to the engine manual packed with your unit or have properly , carburetor adjusted by an authorized service dealer . incorrect fuel mixture . Drain fuel tank . Refill with proper fuel mixture . Excessive vibration Loose parts or damaged auger . Stop engine immediately and disconnect spark plug wire . Tighten all bolts and nuts . Make all necessary repairs . If vibration continues , have unit serviced by an authorized service dealer . Unit fails to propel incorrect adjustment of drive Adjust drive cable . Refer to Adjustment section of this manual . itself cable . Drive belt loose or damaged . Replace drive belt . Refer to Belt Replacement in Maintenance sec - tion of this manual . Unit fails to Discharge chute clogged . Stop engine immediately and disconnect spark plug wire . Clean discharge snow discharge chute and inside of auger housing . Foreign object lodged in auger . Stop engine immediately and disconnect spark plug wire . Remove incorrect adjustment of drive object from auger . cable . Adjust drive cable . Refer to Adjustment section of this manual . Drive belt loose or damaged . Replace drive belt . Refer to Belt Replacement in Maintenance sec - tion of this manual . Shear bolt ( s ) sheared Replace shear bolt ( s ) NOTE : For repairs beyond the minor adjustments fisted above , contact your nearest authorized service dealer or call 1 - 800 - 800 - 7310 for the Customer Support Center . Refer to separate engine manual packed with your snow thrower for more engine related information . 18
ModelsE6OOEE , 610E , E640F , E660G , andE6COF REF . PART RER I PART DESCRIPTION NO . NO . DESCRIPTION NO . I NO . 10 1721 - 0325 1 618 - 0123 Grease Plug RH Reducer Housing Grease Sea ] 2 618 - 0124 11 W21 - 0327 LH Reducer Housing 12 1736 - 0351 3 710 - 0642 Hex Screw 1 / 4 - 20 x , 75 Flat Washer , 76 x 1,5 x , 030 13 1736 - 0369 4 Flat Washer , 508 x 1,0 x , 020 711 - 0908 Spiral Axle 24 " 711 - 0909 14 1736 - 0445 Flat Washer , 76 x 1,5 x , 060 Spiral Axle 26 " 15 1741 - 0662 711 - 0910 Flange Bearing , 75 x 1,0 x , 59 Spiral Axle 28 " 16 1741 - 0663 5 714 - 0161 Key Flange Bearing , 75 x 1,0 x , 925 17 1618 - 0120 6 715 - 0143 Pin - Spiral Ass'y . Complete 24 " 7 717 - 0528 618 - 0121 Worm Gear , 20T Ass'y . Complete 26 " 8 717 - 0526 Worm Shaft 618 - 0122 Ass'y . Complete 28 " 9 718 - 0186 Thrust Collar 19
ModelsE6OOEE , 610E , E640F , E660G , andE6COF 11 10 \ 9 18 15 14 12 \ \ 32 31 21 13 38 _ 23 _ 35 41 - 37 36 18 _ 31 \ 40 20
ModelsE6OOEE , 610E , E640F , E660G , andE6COF REE PART REF . PART NO . NO . DESCRIPTION NO . NO . DESCRIPTION 1 712 - 0116 Lock Jam Nut 3 / 8 - 24 27 736 - 0169 Lock Washer 3 / 8 2 756 - 0178 Flat Idler 28 712 - 0798 Hex Nut 3 / 8 - 16 3 784 - 5632A Snow Shoe Auger idler Arm 30 784 - 5580 4 710 - 0459A Bell Washer Hex Cap Screw 3 / 8 - 24 x 1,50 31 736 - 0242 5 738 - 0281 Shoulder Screw 32 712 - 3010 Hex Nut 5 / 16 - 18 6 736 - 0174 Wave Washer 33 784 - 5581A 24 " Shave Plate 7 732 - 0611 26 " Shave Plate Extension Spring 784 - 5579A 8 712 - 3068 Hex Nut 5 / 16 - 18 784 - 5582A 28 " Shave Plate 9 712 - 3010 Hex Nut 5 / 16 - 18 34 710 - 0260 Carriage Bolt 5 / 16 - 18 x , 62 10 736 - 0119 Lock Washer 5 / 16 35 684 - 0065 Impeller Assembly 11 05931 Pin Housing 36 715 - 0114 12 741 - 0309 Ball Bearing 37 618 - 0120 24 " Gear Assembly 13 710 - 0451 Carriage Bolt 5 / 16 - 18 x . 75 618 - 0121 26 " Gear Assembly 14 705 - 5226 Reinforcement Chute 618 - 0122 28 " Gear Assembly 15 684 - 0039C 24 " Housing Assembly 38 605 - 5188A Spiral 24 " RH 684 - 0040C 26 " Housing Assembly 605 - 5192A Spiral 26 " RH 684 - 0041C 28 " Housing Assembly 605 - 5196A Spiral 28 " RH 16 712 - 3010 Hex Nut 5 / 16 - 18 39 736 - 0188 Flat Washer 18 736 - 0242 Bell Washer 40 741 - 0493A Flange Bushing 19 741 - 0475 Bushing 41 605 - 5189A Spiral 24 " LH Chute Crank Bracket 605 - 5193A 20 784 - 5647 Spiral 26 " LH 21 731 - 1379A Chute Adapter 605 - 5197A Spiral 28 " LH 22 712 - 0324 Hex Lock Nut 1 / 4 - 20 42 710 - 0890A Shear Bolt 5 / 16 - 18 x 1.5 23 736 - 0463 Fiat Washer 43 712 - 0429 Lock Nut 5 / 16 - 18 25 710 - 0703 Carriage Screw 1 / 4 - 20 x . 75 44 741 - 0245 Hex Flange Bearing 26 710 - 0604 Hex Washer Screw 5 / 16 - 18 45 784 - 5618 Bearing Housing 21
ModelsE6OOEE , 610E , E640F , E660G , andE6COF 1 / I I 6 _ 64 1 62 I 33 32 18 \ 19 51 37 34 52 54 44 45 \ 54 58 50 59 \ 22
ModelsE600E , E610E , E640F , E660G , andE6COF REE PART REF . PART DESCRIPTION NO . NO . DESCRIPTION NO . NO . 1 714 - 0507 Cotter Pin 34 710 - 0262 Carriage Bolt 5 / 16 - 18 x 1,56 2 747 - 0877 Rod 35 736 - 0242 Bell Washer , 340 ID x , 872 OD 3 710 - 0599 Hex Washer Screw 1 / 4 - 20 x , 5 36 747 - 0798A Shift Rod 4 784 - 5680 Handle Support Bracket - RH 37 726 - 0100 Push Cap Chute Knob 5 784 - 5679 Handle Support Bracket - LH 38 720 - 0201A 6 748 - 0362 Cam Lock Handle 39 715 - 0138 Roll Pin Chute Crank 7 748 - 0363 Handle Lock Pawl 40 705 - 5204A 8 732 - 0145 Hex Nut 5 / 16 - 18 Compression Spring 41 712 - 3010 Clevis Pin 42 747 - 0697 9 711 - 0653 Chute Crank Eyebolt 10 720 - 0232 Knob 43 735 - 0234 Rubber Grommet 11 684 - 0037 Handle Assy - LH 44 684 - 0008A Shift Arm Assembly 12 784 - 5681 Hex Washer Screw 1 / 4 - 20 x 1,0 Handle Support Bracket - LH 45 710 - 0788 13 784 - 5619A Shift Handle 46 784 - 5599 Handle Tab 14 784 - 5682 Lock Washer 5 / 16 Handle Support Bracket - RH 47 736 - 0119 15 732 - 0746 Torsion Spring 48 710 - 3180 Hex Cap Screw 5 / 16 - 18 x 1.75 16 684 - 0036 Handle Assy - RH 49 710 - 3008 Hex Cap Screw 5 / 16 - 18 x . 75 17 735 - 0199A Flat Washer Rubber Bumper 50 736 - 0185 18 736 - 0509 Washer 51 731 - 0921 Upper Chute 19 736 - 0119 Lock Washer 5 / 16 52 731 - 1300A Lower Chute 20 712 - 3010 Hex Nut 5 / 16 - 18 53 712 - 0429 Hex Lock Nut 5 / 16 - 18 21 746 - 0778 Cable 54 736 - 0159 5 / 16 Washer 22 684 - 0103 Panel 55 710 - 0451 Carriage Bolt 5 / 16 - 18 x . 75 23 712 - 0116 Jam Lock Nut 3 / 8 - 24 56 710 - 0276 Carriage Screw 5 / 16 - 18 x 1,0 24 732 - 0193 Knob Compression Spring 57 720 - 0284 25 736 - 0105 Bell Washer 58 712 - 3027 Hex Lock Nut 1 / 4 - 20 26 714 - 0104 Cotter Pin 59 731 - 0851A Flange Keeper 27 736 - 0275 Flat Washer 5 / 16 60 710 - 3015 Hex Cap Screw 1 / 4 - 20 x . 75 28 711 - 0677 Ferrule 61 725 - 1672 Lens Housing Assembly Â¢ 29 710 - 0459A Hex Cap Screw 3 / 8 - 24 x 1.50 62 747 - 1136 Headlight Retaining Wire t 30 720 - 0274 Grip 63 725 - 1658 Halogen Light t 31 749 - 0910B Handle - RH 64 629 - 0059 Light Harness t 749 - 0911B Handle - LH 65 731 - 1392 Panel w / light t 32 710 - 1003 Hew Washer Screw 66 712 - 0271 Hex Nut 1 / 4 - 20 t 33 731 - 1391 Handle Panel 67 710 - 1003 Hex Washer Screw # 10 - 16 x , 625 t 731 - 1393 Handle Panel w / Top Light 1 If Equipped 23
ModelsE6OOEE , 610E , E640F , E660G , andE6COF p / 37 39 Drive Clutch Cable Auger Clutch 5 4 Cable 13 7 11 _ . 10 6 26 36 Wheels . 13 " or 15 " Wheels 9 10 12 28 I Auger Clutch Cable t5 Blower . Housing 24
ModelsE600E , E610E , E640F , E660G , andE6COF RER PART REF . PART NO . NO . DESCRIPTION NO . NO . DESCRIPTION 1 710 - 1652 Hex Screw 22 717 - 1445 Gear 2 784 - 5688 Drive Cable Guide Bracket 23 714 - 0126 Key 3 784 - 5687A 7 - Tooth Shaft Auger Clutch Cable Bracket 24 717 - 1444 4 756 - 0625 Roller Cable 25 715 - 0249 Roll Pin 5 738 - 0924 Hex Screw 1 / 4 - 28 26 714 - 0143 Klik Pin 6 684 - 0030 Frame Assembly 27 684 - 0042B Friction Wheel Assembly 7 741 - 0563 Friction Disc Wheel Ball Bearing 28 656 - 0012A 8 736 - 0105 Bell Washer 29 684 - 0013B Wheel Shift Rod Assembly 9 712 - 0116 Lock Jam Nut 30 746 - 0897 Drive Cable 10 741 - 0598 Hex Flange Bearing 31 748 - 0190 Spacer 11 736 - 0188 Flat Washer 32 684 - 0021 Friction Wheel Bracket Assembly 12 784 - 5689A Front Support Guide Bracket 33 732 - 0264 Extension Spring 13 710 - 0538 Lock Hex Screw 34 712 - 0711 Jam Nut 3 / 8 - 24 14 736 - 0242 Bell Washer . 340 ID x . 872 OD 35 746 - 0898 Drive Cable 15 714 - 0474 Cotter Pin 36 738 - 0869 Axle 13 " Wheels 16 736 - 0160 Flat Washer . 536 ID x . 930 OD 738 - 0830 Axle 16 " Wheels Hex Washer Screw 1 / 4 - 20 37 784 - 5617A 17 710 - 0788 Friction Plate 18 784 - 5590 Frame Shift Bracket 38 735 - 0243 Friction Wheel Rubber 19 784 - 5638 Frame Cover 39 718 - 0301A Friction Wheel Hub 20 710 - 0599 Hex Washer Screw 1 / 4 - 20 40 618 - 0063 Friction Wheel Bearing 21 736 - 0351 Flat Washer . 760 ID x . 50 OD 5 2 \ 3 WHEEL ASSEMBLIES MODEL SIZE REF . NO . 1 REF . NO . 2 REF . NO . 3 REF . NO . 4 REF . NO . 5 NUMBER WHEEL ASS'Y TIRE AIR RIM SLEEVE COMPLETE ONLY VALVE ONLY BEARING ( 2 ) 31AE600E 13 x 5 734 - 1714 734 - 1527 734 - 6255 734 - 1713 741 - 0401 31AE610E 13 x 5 734 - 1714 734 - 1527 734 - 0255 734 - 1713 741 - 0401 31AE640F 16.5 x 4,8 734 - 1709 734 - 1530 734 - 0255 734 - 1708 741 - 0401 31AE660G 16x 6.5 734 - 1712 734 - 1525 734 - 0255 734 - 1711 741 - 0401 31AE6COF 16.5 x 4,8 734 - 1709 734 - 1530 734 - 0255 734 - 1708 741 - 0401 25
E6OOEE , 610E \ \ \ \ \ \ 11 13 10 27 15 16 _ 20 16 II _ 22 I REF . PART REF . PART NO . NO . DESCRIPTION DESCRIPTION NO . NO . 1 710 - 1652 Hex Washer Screw 1 / 4 - 20 x , 5 15 712 - 0181 Lock Jam Nut 3 / 8 - 16 2 731 - 1324 Belt Cover 16 756 - 0569 Pulley Half 3 732 - 0339 17 736 - 0242 Bell Washer Extension Spring 4 710 - 0627 Hex Screw 5 / 16 - 24 x , 75 18 736 - 0505 Flat Washer 5 19 710 - 3005 736 - 0507 Washer Hex Cap Screw 3 / 8 - 16 x 1,25 6 05896A Drive Clutch Bracket 20 754 - 0430A Belt 7 21 748 - 0234 756 - 0967 Shoulder Spacer Auger Pulley 8 756 - 0985 22 736 - 0247 Flat Washer Pulley Half 9 754 - 0343 V - Belt 23 736 - 0331 Bell Washer 10 756 - 0984 24 710 - 0696 Pulley Half Hex Cap Screw 3 / 8 - 24 11 736 - 0270 Bell Washer 25 748 - 0360 Pulley 12 710 - 0230 26 710 - 0654A Hex Washer Screw 3 / 8 - 16 x 1,0 Hex Cap Screw 1 / 4 - 28 x , 50 13 756 - 0313 Flat Idler 27 629 - 0071 Extension Cord 14 Electric Start Kit 710 - 1245 OEM - 390 - 986 Lock Cap Screw 5 / 16 - 24 26
E640EE660G , andE6COF 2 3 ' \ 4 \ \ \ \ \ 8 9 \ 12 11 16 26 19 19 16 21 22 \ 18 \ " 20 REF . PART REEI PART NO . I NO . DESCRIPTION NO . NO . DESCRIPTION 15 1712 - 0181 1 710 - 1652 Hex Washer Screw 1 / 4 - 20 x . 625 Lock Jam Nut 3 / 8 - 16 16 1756 - 0569 2 731 - 1324 Belt Cover Pulley Half 3 732 - 0710 " _ ' 736 - 0242 Bell Washer Extension Spring 18 1736 - 0505 Flat Washer 4 710 - 0627 Hex Screw 5 / 16 - 24 x . 75 5 710 - 3005 1 # 1754 - 0430A Belt Hex Cap Screw 3 / 8 - 16 x 1,25 20 1756 - 0967 6 05896A Drive Clutch Idler Bracket Auger Pulley # 1 1736 - 0247 Flat Washer 3 / 8 x 1.25 OD 7 748 - 0234 Shoulder Spacer 22 1736 - 0331 Bell Washer 8 756 - 0987 Pulley Half 23 1710 - 0696 9 754 - 0346 V - Belt Hex Cap Screw 3 / 8 - 24 10 756 - 0986 24 1748 - 0360 Pulley Half Adapter Pulley 25 1710 - 0654A Hex Screw 3 / 8 - 16 x 1,0 11 736 - 0270 Bell Washer 12 710 - 0230 26 1629 - 0071 Extension Cord Hex Cap Screw 1 / 4 - 28 x . 50 97 IOEM - 390 - 987 Electric Start 13 756 - 0313 Flat Idler 14 710 - 1245 Lock Hex Cap Screw 5 / 16 - 24 27
MANUFACTURER'S LIMITED WARRANTY FOR : YARD c . Routine maintenance items such as lubricants , filters , The limited warranty set forth below is given by MTD blade sharpening and tune - ups , or adjustments such PRODUCTS INC ( " MTD " ) with respect to new merchandise as brake adjustments , clutch adjustments or deck purchased and used in the United States , its possessions adjustments ; and normal deterioration of the exterior and territories . finish due to use or exposure . d . MTD does not extend any warranty for products sold MTD warrants this product against defects in material and or exported outside of the United States of America , workmanship for a period of two ( 2 ) years commencing on its possessions and territories , except those sold the date of original purchase and will , at its option , repair or through MTD's authorized channels of export distribu - tion . replace , free of charge , any part found to be defective in material or workmanship . This limited warranty shall only No implied warranty , including any implied warranty of apply if this product has been operated and maintained in accordance with the Operator's Manual furnished with the merchantability or fitness for a particular purpose , applies after the applicable period of express written product , and has not been subject to misuse , abuse , com - mercial use , neglect , accident , improper maintenance , warranty above as to the parts as identified . No other alteration , vandalism , theft , fire , water or damage because express warranty or guaranty , whether written or oral , of other peril or natural disaster . Damage resulting from the except as mentioned above , given by any person or installation or use of any accessory or attachment not entity , including a dealer or retailer , with respect to any approved by MTD Products Inc . for use with the product ( s ) product shall bind MTD . During the period of the War - covered by this manual will void your warranty as to any ranty , the exclusive remedy is repair or replacement of resulting damages . the product as set forth above . ( Some states do not allow limitations on how long an implied warranty lasts , so Normal wear parts or components thereof are subject to the above limitation may not apply to you . ) separate terms as follows : All normal wear part or compo - nent failures will be covered on the product for a period of The provisions as set forth in this Warranty provide the 90 days regardless of cause . After 90 days , but within the sole and exclusive remedy arising from the sales . MTD two year period , normal wear part failures will be covered shall not be liable for incidental or consequential loss ONLY IF caused by defects in material or workmanship of or damages including , without limitation , expenses OTHER component parts . Normal wear parts and compo - incurred for substitute or replacement lawn care ser - nents include , but are not limited to . belts , blades , blade vices , for transportation or for related expenses , or for adapters , grass bags , rider deck wheels , seats , snow rental expenses to temporarily replace a warranted thrower skid shoes , shave plates and tires . Batteries are product . ( Some states do not allow the exclusion or limita - covered by a 90 - day limited replacement warranty . tion of incidental or consequential damages , so the above exclusion or limitation may not apply to you . ) HOW TO OBTAIN SERVICE : Warranty service is available , WITH PROOF OF PURCHASE THROUGH YOUR LOCAL In no event shall recovery of any kind be greater than the AUTHORIZED SERVICE DEALER . To locate the dealer in amount of the purchase price of the product sold . Alteration your area , please check for a listing in the Yellow Pages or of the safety features of the product shall void this War - contact the Customer Service Department of MTD PROD - rarity . You assume the risk and liability for loss , damage , or UCTS INC by calling 1 - 800 - 800 - 7310 or writing to RO . Box injury to you and your property and / or to others and their 368022 , Cleveland . Ohio 44136 - 9722 . property arising out of the use or misuse or inability to use This limited warranty does not provide coverage in the the product . following cases : a , The engine or component parts thereof , These items This limited warranty shall not extend to anyone other than carry a separate manufacturer's warranty . Please refer the original purchaser , original lessee or the person for to the applicable manufacturer's warranty on these whom it was purchased as a gift . items . b . Log splitter pumps , valves and cylinders have a sepa - How State Law Relates to this Warranty : This limited rate one year warranty . warranty gives you specific legal rights , and you may also have other rights which vary from state to state .