Register / log-in to add to your Hammerwall Collection.
Manual Location
The Search Results for the Search Section to the left will appear here.
Page: 1
- _ MITSUBISHI THE BIG SCREEN COMPANY " Owner's Guide Projection Television Models WT - 42313 , WS - 48313 , WS - 55313 and WS - 65313
Page: 2
IF IOSFKELECTRIC SHOCK DO NOT OPEN I • CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK , DO NOT REMOVE COVER OR BACK . NO USER SERVICEABLE PARTS INSIDE . REFER SERVICING TO QUALIFIED SERVICE PERSONNEL . user of the presence of uninsulated " dangerous voltage " within the product's enclosure that may be The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the sufficient magnitude to constitute a risk of electric shock . The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance ( servicing ) instructions in the literature accompanying the appliance . Warning : To avoid permanently imprinting a fixed image onto your TV screen , please do not display the same stationary images on the screen for more than 15 % of your total TV viewing in one week . Examples of stationary images are letterbox top / bottom bars from DVD disk or other video sources , side bars when showing standard TV pictures on widescreen TV's , stock market reports , video game patterns , station logos , web sites or stationary computer images . Such patterns can unevenly age the picture tubes causing permanent damage to the TV . Please see page 6 , 12 or 30 for a detailed explanation . Note : This equipment has been tested and found w comply with the limits for a Class B digital device , pursuant to part 15 of the FCC Rules . These limits are designed to provide reasonable protection against harmful interference in a residential installation . This equipment generates , uses and can radiate radio frequency energy and , if not installed and used in accordance with the instructions , may cause harmful interference to radio communications . However , there is no guarantee that interference will not occur in a particular installation . If this equipment does cause harmful interference to radio or television reception , which can be determined by turning the equipment off and on , the user is encouraged to try to correct the interference by one or more of the following measures : • Reorient or relocate the receiving antenna . • Increase the separation between the equipment and the receiver . • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected . • Consult the dealer or an experienced radio / TV technician for help . Changes or modifications not expressly approved by Mitsubishi could void the user's authority to operate this equipment . WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK , DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE . CAUTION : TO PREVENT ELECTRIC SHOCK , MATCH WIDE BLADE OF PLUG TO WIDE SLOT , FULLY INSERT . NOTE TO CATV SYSTEM INSTALLER : THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO ARTICLE 820 - 40 OF THE NEC THAT PROVIDES GUIDELINES FOR THE PROPER GROUNDING AND , IN PARTICULAR , SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING , AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL .
Page: 3
Contents hnportant Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Chapter 1 Television Overview Thank you . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Unpacking your New TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Special Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Front Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Back Pand Input / Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 hnportant Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Chapter 2 Connections Connecting an Antenna or Wall Outlet Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Connecting an Antenna to a Cable Box or VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Connecting an Antenna to a Cable Box and VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Connecting Audio Components to a Cable Box or VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Connecting an Audio Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Connecting a DVD Player or Other S - Video Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Connecting a DTV Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Connecting MonitorLink ' _ _ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 How Connections Affect the PIP and POP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Chapter 3 Remote Control Functions Overview of the TV Layer Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Care and Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Channel Sdection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Use With Other A / V Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Special Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Operation of P1P and POP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 hnportant Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Chapter 4 Menu Screen Operations The ViewPoint * Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 MAIN Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 SETUP Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 CAPTIONS Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 CHANNEL EDIT Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 V - CHIP LOCK Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 ADVANCED FEATURES Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 AUDIO / VIDEO SETTINGS Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Chapter 5 PIP / POP Operations Operation of PIP and POP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Available On - Screen Format Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Appendix A : Bypassing the V - Chip Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Appendix B : HD Input Connection Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Appendix C : Remote Control Programming Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Appendix D : Cleaning and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Appendix E : Diamond Shidd ' _ Installation and Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Page: 4
IMPORTANT SAFEGUARDS Please read the following safeguards for your TV and retain for future reference . Always follow all warnings and instructions marked on the television . 1 . Read , Retain and FollowAll Instructions Read all safety and operating instructions before operating the TV . Retain the safety and operating instructions for future reference . Follow all operating and use instructions . 2 . Heed Warnings Adhere to all warnings on the appliance and in the operating instructions . 3 . Cleaning Unplug the TV from the wall outlet before cleaning . Do not use liquid , abrasive , or aerosol cleaners . Cleaners can permanently damage the cabinet and screen . Use a lightly dampened cloth for cleaning . 4 . Attachments and Equipment Never add any attachments and / or equipment without approval of the manufacturer as such additions may result in the risk of fire , electric shock o1 " other personal injury . 5 . Water and Moisture Do not use the TV where contact with or immersion in water is possible . Do not use near bath tubs , wash bowls , kitchen sinks , laundry tubs , swimming pools , etc . 6 . Accessories Do not place the TV on an unstable cart , stand , tripod , or table . The TV may fall , causing serious injury : o a child or adult and serious damage m the TV . Use only with a cart , stand , tripod , bracket , or table : ecommended by the manufacturer , or sold with the TV . Any mounting of the TV should follow the manufacturer's instructions , and should use mounting accessories recommended by the manufacturer . _ _ nappliance and cart combination should be moved with care . O . uick stops , excessive force , and uneven mrfaces may cause the appliance and cart combination m overturn . Z Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the TV and to protect it from overhearing . Do not block these openings or allow them to be obstructed by placing the TV on a bed , sofa , rug , or other similar surface . Nor should it be placed over a radiator or heat register . If the TV is to be placed in a rack or bookcase , ensure that there is adequate ventilation and that the manufacturer's instructions have been adhered to . 8 . Power Source This TV should be operated only from the type of power source indicated on the marking label . If you are not sure of the type of power supplied to your home , consult your appliance dealer or local power company . 9 . Grounding or Polarization This TV is equipped with a polarized alternating cm'rent line plug having one blade wider than the other . This plug will fit into the power outlet only one way . If you are unable to insert the plug fully into the outlet , try reversing the plug . If the plug should still fail to fit , contact your electrician to replace your obsolete outlet . Do not defeat the safety pro'pose of the polarized plug . 10 . Power - Cord Protection Power - supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them , paying particular attention to cords at plugs , convenience receptacles , and the point where they exit from the TV . 11 . Lightning For added protection for this TV during a lightning storm , or when it is left unattended and unused for long periods of time , unplug it from the wall outlet and disconnect the antenna or cable system . This will prevent damage to the TV due to lightning and powerqine surges . 4
Page: 5
IMPORTANT SAFEGUARDS , continued 12 . Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits , or where it can fall into such power lines or circuits . When installing an outside antenna system , extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal . 13 . Overloading Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock . 14 . Object and Liquid Entry Never push objects of any kind into this TV through openings as they may touch dangerous voltage points or short - out parts that could result in fire or electric shock . Never spill liquid of any kind on or into the TV . 15 . Outdoor Antenna Grounding If an outside antenna or cable system is connected to the TV , be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built - up static charges . EXAMPLE OF ANTENNA GROUNDING Section 810 of the National Electric Code , ANSI / NFPA No . 70 - 1984 , provides LEAD _ N WIRE information with respect to proper grounding of the mast and supporting structure , grounding of the lead in wire to an antenna discharge unit , size of grounding GRQUND CLAMp ANTENNA DISCHARGE UNIT conductors , location of antenna discharge unit , connection m grounding electrodes , { NEC SECT _ QN 810 20 ) and requirements for the grounding electrode . GROUNDING _ i NT _ CNNATORS CONDU { NEC S ECT _ Q N 910 21 ) 16 . Servicing lIND CLAMPS Do not attempt to service this TV yourself as opening or removing covers may expose _ pOWER S Ef _ VLCE GROUNDING ELECTRODE SYSTEM you to dangerous voltage or other hazards . Refer all servicing m qualified service NEC NATIONAL ELECTRICAL CODE ( NUC ART 250 , PART H ) personnel . 1Z Damage Requiring Service Unplug the TV from the wall outlet and refer servicing to qualified service personnel under the following conditions : ( a ) When the power - supply cord or plug is damaged . ( b ) If liquid has been spilled , or objects have fallen into the TV . ( c ) If the TV has been exposed to rain or water . ( d ) If the TV does not operate normally by following the operating instructions , adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the TV to its normal operation . ( e ) If the TV has been dropped or the cabinet has been damaged . ( f ) When the TV exhibits a distinct change in performance - this indicates a need for service . 18 . Replacement Parts When replacement parts are required , be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part . Unauthorized substitutions may result in fire , electric shock or other hazards . 19 . Safety Check Upon completion of any service or repair to the TV , ask the service technician to perform safety checks to determine that the TV is in safe operating condition . 20 . Heat The product should be situated away from heat sources such as radiators , heat registers , stoves , or other products ( including amplifiers ) that produce heat . 5
Page: 6
IMPORTANT NOTES Warning : Do not leave stationary PIP / POP , or letterbox images on the screen for extended periods of time . Mix the types of pictures shown . Uneven picture tube aging is NOT covered by your warranty . The normal use of a TV should include a Examples of these types of images can be , but mixture of TV picture types . The most are not limited to the following : frequently used picture types should fill the screen with constantly moving images Letterbox top / bottom black bars : rather than stationary images or patterns . shown at the top and bottom of the TV screen Displaying the same stationary patterns over when you watch a widescreen ( 16 : 9 ) movie on extended periods of time or displaying the a standard ( 4 : 3 ) TV . same stationary pattern frequently can leave subtle but permanent ghost images . To avoid Side bar images : this , mix your viewing pattern and reduce the solid bars shown on each side of an image initial contrast level . Do not show the same when watching a standard ( 4 : 3 ) program on a stationary image for more than 15 % of your total TV viewing in any given week . Display widescreen ( 16 : 9 ) TV . constantly moving and changing images that fill the screen whenever possible . _ . News and stock - market report bars : ticker running at the bottom of the TV screen . This projection TV uses picture tubes to project the image to the screen . All picture tubes age with Shopping channel logos & pricing displays : use . As they age , their light output is gradually bright graphics that are shown constantly or reduced . Normal TV pictures fill the screen repeatedly in the same location . with constantly changing images . Under these conditions , picture tubes age at an even rate across the entire screen . This maintains Video game patterns and scoreboards a TV picture that is evenly bright over the whole screen . Stationary images or images Bright station logos : that only partially fill the screen ( leaving black moving or low - contrast graphics are less likely or colored bars to fill the screen ) , when used to cause uneven aging of the picture tubes . over extended periods of time or when viewed repeatedly , can cause uneven aging of the Online ( Internet ) websites : phosphors and leave subtle ghosts from the or any other stationary or repetitive computer stationary images in the picture . style images , including digital photos . Still or stationary images may be received from Closed Captioning broadcasters , cable channels , satellite channels , Mitsubishi recommends using a gray DVD discs , video tapes , laser discs , on - line background rather than a black or a bright services , web / Internet searching devices , video color if you frequently use closed captioning . games , and digital TV tuner / converter boxes . 6
Page: 7
illll _
Page: 8
Thank You for Your Purchase Welcome to the wonderful and exciting world of digital television ! We are honored that you chose Mitsubishi as your premier home entertainment partner . The development team at Mitsubishi Digital Electronics America ( MDEA ) understands that our customers demand and expect the very best . MDEA was founded on the core beliefs and philosophies that drive us to deliver products that implement the latest in advanced television technology . While some televisions are destined for obsolescence in the near future , MDEA's televisions are all HD - upgradeable . This cornerstone of your home entertainment system will continue to provide unparalleled enjoyment for years to come ! Whether this is your first Mitsubishi consumer electronics product or another addition to your growing Mitsubishi system , we hope that this television will bring you many hours of enjoyment . OUR PROMISE We will engineer and manufacture the upgrades necessary so the HD - upgradeable television you purchased today can be made compatible with near - future advances in digital television and digital interconnectivity . Specifically , we promise that you will be able to have your television upgraded , at a reasonable cost , to include an off - air HDTV tuner , a cable TV tuner ( for unscrambled programming ) , an IEEE 1394 ( FireWire ® ) connection , HAVi system control , and 5C copy protection . 8
Page: 9
Unpacking Your New TV Special Features Please take a moment to review the following list of Your new High Definition ( HD ) upgradeable items to ensure that you have received everything bigscreen television has many special features that make including : it the perfect addition to your home entertainment system . A few of these special features are : PIP / POP Viewing Option Using Picture - in - Picture and Picture - outside - < 9 @ Picture gives you exciting options for viewing favorite programs . 2J JC22 ) Seepages 22 , 29 and 62for more information . HD Upgradeable With the use of an optional HDTV receiver ( Mitsubishi HD - 5000 or similar model ) your Mitsubishi bigscreen can display high definition pictures . Seepage 21for connection information . Remote Control Multibrand Remote Control Your Mitsubishi remote control can be programmed to control many other audio / video components . Seepages 27 - 28 for more information . V - Chip Technology Mitsubishi understands you may want to shield certain viewers from specific program content . Your Mitsubishi bigscreen will allow you to restrict 2 AAA Batteries programming by general contents , specific contents , or even by time . Seepages 45 - 49for more information . 16 : 9 Widescreen TV Enjoy a full theatrical experience in the comfort of your home . View pictures as film directors intended them . Both the DTV and DVD support the widescreen format well - suited for your new TV . Seepages 60 - 61 for more information . Product Registration Card Quick Reference Card ( notpictured ) 9
Page: 10
Front Control Panel Many remote control buttons are duplicated on the front control panel . Duplicate buttons are shaded in the panels shown below . Please see Remote Control Functions , page 24 , for an explanation of their usage . S - VIDEO VIDEO L - AUDIO - R TEMER _ i INPUT 3 The ADJUST , ENTER , MENU , and CANCEL buttons may be used to access or navigate through the screen menus Timer F During normal operation , the timer light glows green gZ ] when the TV is on . It does not glow when the TV is off . When the timer is used to turn the TV on at a TIMER specific time , the green timer light blinks while the TV is off . See Timer Menu , page 51 for timer setup instructions . A / V Reset Press this button to reset all A / V memory inputs to AN RESET the factory default settings . See Audio / Video Settings Menu , page 55 for instructions . CANCEL Format FORMAT Press this button to change the size and shape of the main TV picture . ENTER S - VIDEO VIDEO L - AUDIO - R Input - 3 This input can be used for convenient connection of a camcorder or other video device to the TV . You may ® ° connect to the S - VIDEO or VIDEO terminal but not to both . 10
Page: 11
Back Panel Input / Output for WS - 48313 , WS - 55313 & WS - 65313 Side Panel Input / Output for WT - 42313 WT - 42313 Side Panel WS - 48313 , WS - 55313 , WS - 65313 Back Panel 2 3 4 - 7 . 1 . ANT - A , LOOP OUT and ANT - B ( Antenna ) DTV Input This input is used to connect a DTV receiver or cable box ANT - A and ANT - B receive signals from VHF / UHF antennas and can be configured for HDTV component ( YPbPr ) , or or a cable system . LOOP OUT sends the ANT - A signal out to another device , such as a cable box or VCR . RGB plus H & V . Please see Appendix B , page 65 , for signal compatibility . Note : LOOP OUT is disabled when Energy Mode is set to Low when the TV power is set to Off . 6 . MonitorLink _ M / DVI 2 . Monitor Out This is a Mitsubishi - exdusive proprietary digital interface for the display of high quality digital video signals from Mitsubishi The Monitor Output sends the TV audio and video signals products such as the HD - 5000 HDTV Receiver / Controller . ( excluding component video , DTV video and MonitorLink ) to All video signals , both analog and digital are sent digitally to an A / V receiver or other equipment . your Mitsubushi TV . Can also be used as a DV1 input for other compatible sources . 3 . Inputs 1 - 2 Note : The DVI - HDTV input terminal is compliant with the These inputs can be used for the connection ofa VCR , Super EIA - 861 standard and is not intended for use with personal VHS ( S - VHS ) VCR , laser disc player , or other A / V device to computers . the TV [ With each input , you may connect to the S - VIDEO or VIDEO terminal but not to both . 7 . MonitorLink _ MControl / RS - 232C A digital control interface that works in parallel with 4 . Component Inputs 1 - 2 ( Component only for MonitorLink . While MonitorLink provides the digital video WT - 42313 ) signal , MonitorLink Control provides enhanced functioning These inputs can be used for the connection of A / V equipment such as automatic power ON / OFF and input selection . Can with component video outputs , such as a DVD player or also be used with other compatible RS - 232C external control compatible Video Game System . Please see Appendix B , page devices . 65 , for signal compatibility . 11
Page: 12
IMPORTANT NOTES Warning : Do not leave stationary PIP / POP , or letterbox images on the screen for extended periods of time . Mix the types of pictures shown . Uneven picture tube aging is NOT covered by your warranty . The normal use of a TV should include a Examples of these types of images can be , but are mixture of TV picture types . The most not limited to the following : frequently used picture types should fill the screen with constantly moving images Letterbox top / bottom black bars : rather than stationary images or patterns . shown at the top and bottom of the TV screen Displaying the same stationary patterns over when you watch a widescreen ( 16 : 9 ) movie on extended periods of time or displaying the a standard ( 4 : 3 ) TV . same stationary pattern frequently can leave subtle but permanent ghost images . To avoid Side bar images : this , mix your viewing pattern and reduce the solid bars shown on each side of an image initial contrast level . Do not show the same when watching a standard ( 4 : 3 ) program on a stationary image for more than 15 % of your widescreen ( 16 : 9 ) TV . total TV viewing in any given week . Display constantly moving and changing images that fill the screen whenever possible . Stock - market report bars : ticker running at the bottom of the TV screen . This projection TV uses picture tubes to project the image to the screen . All picture tubes age with Shopping channel logos & pricing displays : use . As they age , their light output is gradually bright graphics that are shown constantly or reduced . Normal TV pictures fill the screen repeatedly in the same location . with constantly changing images . Under these conditions , picture tubes age at an even rate across the entire screen . This maintains Video game patterns and scoreboards a TV picture that is evenly bright over the whole screen . Stationary images or images Bright station logos : that only partially fill the screen ( leaving black moving or low - contrast graphics are less likely or colored bars to fill the screen ) , when used to cause uneven aging of the picture tubes . over extended periods of time or when viewed repeatedly , can cause uneven aging of the Online ( Internet ) websites : phosphors and leave subtle ghosts from the or any other stationary or repetitive computer stationary images in the picture . style images . Still or stationary images may be received from Closed Captioning broadcasters , cable channels , satellite channels , Mitsubishi recommends using a gray DVD discs , video tapes , laser discs , on - line background rather than a black or a bright services , web / Internet searching devices , video color if you frequently use closed captioning . games , and digital TV tuner / converter boxes . 12
Page: 13
2 Connecting a DVD Player or O _ er S - Video Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Connecting a DTV Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Connecting MonitorLink TM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 How Connections Affect the PIP and POP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Page: 14
Connecting an Antenna or Wall Outlet Cable VHF _ tenna O _ F _ a _ t _ r _ a - { O _ at _ no _ 2s 13 } ( Chatv _ _ 4 69 Separate UHF and VHF Antennas ( Figure 1 ) Flat T _ Log F _ atTwin L _ d 1 . Connect the UHF and VHF antenna leads to the o _ Cable UHF / VHF combiner . " rv back panel ( section detail ) 2 . Push the combiner onto ANT - A on the TV back panel . UHF / VHF combiners are not provided with _ * Back 8 _ de the TV . They are available at most electronic stores . [ ] Figure l . Connecting separate UHF and VHF antennas . Note : This TV will only be able to provide an analog signal through ANToA on the TV back panel . Note : Seepage 5for Outdoor Antenna Grounding Twin Lead Antenna , Coaxial Lead Antenna , or Wall Outlet Cable ( Figure 2 ) For antenna with twin flat leads : TV back panel { section detail ) 1 . Connect the 300ohm twin leads to the transformer . 2 . Push the 75ohm side of the transformer onto ANToA on the TV back panel . op _ io _ al 3oo Ohm to ZS O _ n Mat _ h _ ng _ ransfo _ 300ohm to 75ohm matching transformers are not provided Figure2 . Connecting twin lead antenna , coaxial lead with the TV . They are available at most electronie stores . antenna , or wall outlet cable . For cable or antenna with coaxial lead : Note : Seepage 5for Outdoor Antenna Grounding 3 . Connect the incoming cable to ANT - A on the TV back panel . Note : This TV will only be able to provide an analog signal through ANToA on the TV back panel . 14
Page: 15
Connecting an Antenna to a Cable Box or VCR TV back panel ( section detail ) Cable Box ( Figure 3 ) Ncoming CaNe 1 . Connect the incoming cable to ANT - A on the TV back panel . Connect two coaxial cables as follows : 2 . One from LOOP - OUT on the TV back panel to IN [ ] on the cable box back panel . 3 . One from OUT on the cable box back panel to ANT - B on the TV back panel . o eBox NOTE : If your cable box has separate audio ! video k panel £ ectioi ° I outputs , please see Composite Video with Figure 3 . Connecting the cable box . Audio or S - Video with Audio , page 16 ( Figure 6 ) . Note : Seepage 5for Outdoor Antenna Grounding TV back panel ( section detail ) Antenna or Wall Outlet Cable ( Figure 4 ) 1 . Connect the incoming cable to ANT - A on the TV back panel . Connect two coaxial cables as follows : 2 . One from LOOP - OUT on the TV back panel to ANTENNA IN on the VCR back panel . VCR back pane ] 3 . One from VCR back panel ANTENNA OUT to • t J ANT - B on the TV back panel . t l NOTE : If your cable box has separate audio ! video Figure 4 . Connecting the VCR with antennas or wall outputs , please see Composite Video with outlet table . Audio or S - Video with Audio , page 16 ( Figure 6 ) . 15
Page: 16
Connecting an Antenna to a Cable Box and VCR , Connecting Audio / Video to the Cable Box or VCR TV back panel ( section detail ) Cable Box Incoming Cable ( Figure 5 ) 1 . Connect the incoming cable to ANT - A on the TV [ ] [ ] back panel . Connect three coaxial cables as follows : Cable Box 2 . One from LOOP - OUT on the TV back r _ _ _ a _ . . _ _ Rear Terminals panel to IN on the back of the cable box . 3 . One from OUT on the back of the cable box to ANTENNA IN on the VCR back panel . 4 . One from ANTENNA OUT on the VCR back panel to ANT - B on the TV back panel . Figure 5 . Connecting the VCR with cable box . NOTE : For best performance , please see Composite Video with Audio or S - Video with Audio , below . Composite Video with Audio or S - Video with Audio ( Recommended ) ( Figure 6 ) TV back panel ( section detail ) . Connect a video or an S - Video cable from VIDEO OUT on the VCR back panel to VIDEO or ( Recommended if available ) S - VIDEO , INPUT - 1 or INPUT - 2 on the TV back panel . 2 . Connect a set of audio cables from AUDIO OUT on the VCR back panel to AUDIO INPUT - 1 or INPUT - 2 on the TV back panel . • The red cable connects to the R ( right ) channel • The white cable connects to the L ( left ) channel If your VCR is mono ( non - stereo ) , connect only the white ( left ) cable . Figure 6 . Connecting the VCR Audio / Video . You may connect to the S - VIDEO or VIDEO terminal but not to both . 16
Page: 17
Connecting an Audio Receiver TVbaok panel Stereo Audio System ( recommended for shelf units or A / V receivers without digital audio inputs ) ( Figure 7 ) Connect the audio cables from AUDIO . MONITOR OUTPUT on the TV back panel to TV IN or AUX IN terminals on the back of the audio system . [ ] • The red cable connects to the R ( right ) channel • The white cable connects to the L ( left ) channel 2 . Turn off the TV's speakers through the AUDIO / VIDEO SETTINGS Menu , page 55 . Audio system back panel section 3 . Set the audio system's input to the TV or AUX position to hear the TV's audio through your stereo system . Figure Z Connecting the StereoAudio System . A / V Receiver ( Figure 8 ) . Connect either a video cable or an S - Video cable ( but not both ) from VIDEO MONITOR OUT on the back of the A ! V receiver to VIDEO INPUT - 1 or INPUT - 2 on the TV back panel . 2 . Connect a video cable from VIDEO MONITOR OUTPUT on the TV back panel to VIDEO TV IN on the back of the A / V receiver . 3 . Connect a set of audio cables from AUDIO MONITOR OUTPUT on the TV back panel to AUDIO TV IN on the back of the A / V receiver . • The red cable connects to the R ( right ) channel Figure8 . ConnectingtheA / VReceiver . • The white cable connects to the L ( left ) channel 17
Page: 18
Connecting a DVD Player or Other S - Video Device DVD Player with Component [ ] Video ( Figure 9 ) . Connect the Component Video cables from ( YCbCr or YPbPr ) VIDEO OUT on the back of the DVD player to COMPONENT ( 1 or 2 ) on the TV back panel . The correct connections are : A . YtoY E B . Cb or Pb to Pb C . Cr or Pr to Pr Figure 9 . Connecting a DVD Player _ ith Component 2 . Connect a set of audio cables from AUDIO OUT Video . on the back of the DVD player to COMPONENT AUDIO Input ( 1 or 2 ) on the TV back panel . • The red cable connects to the R ( right ) channel iMPORTANT • The white cable connects to the L ( left ) channel NOTE : Some video game systems support component connections . Please refer to your video game console Owner's Guide . NOTE : If your DVD player supports progressive scan playback , be sure to set your player TV back panel ( section detail ) accordingly . Please refer to your DVD player's Owner's Guide . Other S - Video Device ( Figure 10 ) 1 . Connect an S - Video cable from VIDEO OUT on the device back panel to VIDEO INPUT - 1 or INPUT - 2 on the TV back panel . 2 . Connect a set of audio cables from AUDIO OUT [ ] on the device back panel to AUDIO INPUT - 1 or INPUT - 2 on the TV back panel . • The red cable connects to the R ( right ) channel • The white cable connects to the L ( left ) channel Figure 10 . Connecting an S - Video Device . If your S - Video Device is mono ( non - stereo ) , connect only the white ( left ) cable . 18
Page: 19
Connecting a DTV Receiver DTV Connectors and Adaptors ( Figure 11 ) The TV back panel has five RCA - type connectors for the DTV connection . The back panel of your DTV receiver may use RCA - type connectors or BNC - type or connectors . If your DTV receiver comes with BNC BNC to A or RCA type connections , you will need to purchase BNC to RCA BNC Fitted to Connector RCA adaptors to connect the TV to the DTV receiver . Adaptor Connector Connection These adaptors should be available at most electronic Figure ll . DTVconnectors and adaptors . supplystores . DTV Receiver with Component Video Connections ( Recommended ) ( Figure 12 ) Connect the outside antenna cable , or satellite to . ANT or SATELLITE IN on the DTV receiver ( see your DTV receiver owner's guide for instructions and cable compatibility ) . w _ ek p _ I * _ en _ ta _ . If your DTV receiver has a built - in terrestrial tuner , a " % 7 . . 1 . . . . . . connect the incoming terrestrial antenna to ANT on the DTV receiver . If your DTV receiver does not have a built - in terrestrial tuner , this TV will L . only be able to provide an analog signal through Ant - A on the TV back panel . 3 . Connect the RCA - type cables from the DTV receiver outputs to DTV INPUT Y ! Pb / Pr on the TV back panel . You may need to set the DTV Input Assignment to Y / Pb / Pr ( see page 35 ) . [ ] 4 . Connect the L ( left ) and R ( right ) audio cables from the DTV receiver to DTVAUDIO on the TV ba & panel . Figure l2 . Connecting the DTVrecei _ ' er with 5 . To utilize the benefits of a digital A ! V receiver , component Video Connections . connect your DTV receiver's digital audio out to a digital input on your digital A / V receiver . Component ( 1 and 2 ) may also be used for 1080i components . 19
Page: 20
DTV Receiver with RGB Video Connections ( Figure 13 ) . Connect the outside antenna , cable , or satellite to ANT or SATELLITE IN on the DTV receiver ( see your DTV receiver owner's guide for instructions and cable compatibility ) . . If your DTV receiver has a built - in terrestrial tuner , connect the incoming terrestrial antenna to ANT on the DTV receiver . If your DTV receiver does [ ] Figure13 . Connecting the DTVreceiver with RGB not have a built - in terrestrial tuner , this TV will video connections . only be able to provide an analog signal through Ant - A on the TV back panel . . Connect the RGB cables from the DTV receiver to the TV back panel as listed below ( if your DTV receiver uses BNC - type cables , use the adaptors shown in Figure 11 , page 19 ) : DTV Receiver TV Back Panel G ( green ) Y / G B ( blue ) Pb / B R ( red ) Pr / R . If the DTV receiver has outputs for H and V sync , connect as listed below ( DO NOT connect if DTV receiver uses " Sync on Green " ) : H ( horizontal sync ) H V ( vertical sync ) V . Connect the L ( left ) and R ( right ) audio cables from the DTV receiver to DTV AUDIO on the TV back panel . . To utilize the benefits of a digital A ! V receiver , connect your DTV receiver's digital audio out to a digital input on your digital A / V receiver . You may need to setup the DTV ( See Input Assignment , page 35 ) to RGB . 20
Page: 21
MonitorLink WS - 48313 , WS - 55318 , WS - 65313 back pane _ ( Figure 14 ) [ ] 1 . Connect a MonitorLink / DVI cable from the TV back panel to the Mitsubishi HD Receiver / . _ - o Controller back panel . o 2 . Connect the MonitorLink Control / RS - 232 cable from the TV back panel to the Mitsubishi HD Receiver / Controller back panel . . Connect the L ( left ) and R flight ) audio cables from the HDTV receiver to AUDIO LEFT and AUDIO RIGHT on the MonitorLink section of the TV back panel . NOTE : The 29 pin MonitorLink ! DVI and RS - 232 Figurel4 . ConnectingMonitorLink cables can be found at your local electronics store . CAUTION : To assure continued FCC compliance , the user must use a shielded video interface cable with bonded ferrite cores at each end , when using the MonitorLink / DVI input . 21
Page: 22
How Connections Affect the PIP ( Picture - In - Picture ) and POP ( Picture - Outside - Picture ) To see a picture in the PIP or POP , you may need to select an input source . If the only input connected is ANT - A , then both the main picture and the PIP / POP will be from that input source . If other video equipment is connected , you may be able to view these input sources as the PIP / POP . When connecting your new Mitsubishi TV , it is important to understand which main picture and PIP / POP input sources can and cannot be used together . The table on this page shows which inputs can and cannot be used together and the limitations they may have . If you press the INFO button it will display the current Input , signal ( 480i , 480p , or 1080i ) , format , time , day and sleep time . See Operation of PIP and POP , page 62 , for operating instructions . 180 ! % ! % ¸ ! OK * No PIP / POP OK OK OK OK OK * OK OK OK OK OK OK * * OK OK OK OK OK OK * * OK OK OK OK OK OK * * OK OK OK OK OK * No Side - by - Side with the same channel * * No Side - by - Side with the same input t Component 2 is not available on the WT - 42313 22
Page: 23
3 Operation of PIP and POP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Page: 24
Remote Control Functions : Overview of the TV Layer Buttons AUDIO : Select the individual audio settings . Overview ( Figure 1 , following page , ) VIDEO : Select the individual video settings . Slide Switch : Select A / V product to be controlled by PIP CH : Scroll up or down through memorized the remote control . channels in PIP or POP . POWER : Turns power on and off for TV and other PIP / POP : Cycle through PIP and POP display connected A / V products . choices . Numbers : Individually select channels or input EXCH : Exchange PIP or POP with the main TV information into TV . picture . SQV ( Super O _ ick ViewTM ) : Scan through a SLEEP : Set the TV to turn offwithin 2 hours . See memorized list of favorite channels . Sleep Timer , page 26 , for setup instructions . Q V ( Oafick ViewTM ) : Switch to last channel viewed . PIP INPUT . ' Select the PIP or POP input source . GUIDE : When the slide switch is set to CABLE / FORMAT : Change the shape and size of the main DBS / DTV , display the on - screen program guide TV picture . ( some cable boxes and DBS / DTV receivers ) . REC : Manually record with your VCR or recordable INPU _ Select the signal to view ; Ant - A , Ant - B , DVD . DTV , Component - i , Component - 2 , Input - l , REW / REV : Rewind or reverse search with your Input - 2 , Input - 3 , MonLink . ( Component 2 not VCR , reverse scan with your DVD , or skip reverse available on WT - 42313 . ) with your CD . CH ( channel ) : Scroll up or down through memorized PLAY : Play your VCR , DVD , or CD . channels . Skips DVD chapters in DVD layer . STOP : Stop your VCR , DVD , or CD . VOL ( volume ) : Change sound level . FF / FWD : Fast forward or forward search with MUTE : Turn sound on or off . your VCR , fast play with your DVD , or skip for - MENU : Display _ E ® on - screen menu system . ward with your CD . ADJUST . ' Navigate menus , change settings , and move the PIP on - screen location . PAUSE : Pause your VCR , DVD , AV Disc , or freeze the PIP or POP image . ENTER : Select a channel number or menu item . HOME : Exit on - screen menus and return to TV LIGHT : Illuminates buttons or labels on the remote control . Located on the left side of the remote . viewing . CANCEL : Clear SQV and some menu entries . Used as a subchannel button in Cable / DBS / DTV layer . V - CHIP : Displays V - Chip Passcode screen , use to enable or disable the V - Chip Lock . INFO : Displayon - screen summaryofthe current input used and any broadcast information available ( including current V - Chip information , Signal Source and Format ) . Additionally , if you press the INFO key , it will display time , day and sleep time . 24
Page: 25
Remote Control Functions : Care and Operation rT - Operation VOR CASLg / O88 / _ ) W DVD ( II ) ) Installing the Batteries : ( Figure 2 ) < o ® 1 . Remove the remote control's back cover by gently pressing the ridged tab in the direction of the arrow q ) < 9 < 9sLEEp and sliding off the cover . VIDEO _ NPUT CHANNEL VOLUME 2 . Load the batteries , making sure the polarities ( + ) and ( - ) are correct . For ease of installation , install J J J the negative ( - ) side first . For Best Results from the Remote Control : _ . Be within 20 feet of the equipment . iiiilQu { _ _ . Do not press two or more buttons at the same time REC gTOP PAUSE unless instructed to . _ . Do not allow to get wet or become heated . REW / g / EV pt _ y FF / FWD _ . Avoid dropping on hard surfaces . _ N'I ' _ NN - II _ . Do not use harsh chemicals to dean . Use only a soft , lightly moistened cloth . Figure1 . Remote ControlFunctions . Do not mix new and old batteries . Do not heat , take apart , or throw batteries into fire . Use only AAA batteries . size AAA batteries Operating the Remote Control : You can use the remote to control the TV , CABLE / DBS / DTV , VCR , DVD , and AUDIO products . Select the product you want to control by moving the slide switch to the appropriate position . The remote Figure2 . Installing the batteries . control has been preset to operate the TV and other Mitsubishi products . To program the remote control to operate other products , see Use of the Remote Control with Other A / V Products , page 27 . 25
Page: 26
Remote Control Functions : Channel Selection , Sleep Timer Channel Selection Enter three numbers ( ex . for channel 2 , press 002 ) . or Press the channel number and ENT ( ex . for channel 2 , press 2 , then ENT ) . or Enter the channel number and wait four seconds ( without pressing ENT ) . The TV will change automatically . r7 - TV _ 1 I IF AUDIO Sleep Timer ( Figure 3 & 4 ) Setting the Sleep Timer : Press SLEEP on the remote control . ) QQ A message indicating the length of time the sleep timer is to be set appears on the TV screen . ) Q ® sLEEP Each press of SLEEP will increase the time Q ® Q displayed by 30 minutes , until the maximum value of 120 minutes is reached . Figure 3 . Sleep button on remote control _ . After 5 seconds of inactivity , the message will disappear . Sleep : 30 min . Press SLEEP to view the remaining time before the timer turns the TV off . Canceling the Sleep Timer : Press the SLEEP button to display the on - screen message . Press SLEEP repeatedly until OFF is displayed . Figure 4 . On - screen display for sleep timer After 5 seconds of inactivity , the message will disappear . 26
Page: 27
Use of the Remote Control with Other A / V Products CABLE / DBS / DT _ VCR DVDt - TV - o _ _ , _ AUDIO I II I I 1 . ( ( ( , ] " ) ) Programming the Remote Control to Use with Other Brands of Audio 1 Cable box brand Code _ enten eIfyour and Video Products : cabl box General Instruments / 119,120,121,122,123 , code is not Jerrold 124 ( Figures 1 - 3 this page , figures 4 - 5 following page ) listed here , Motorola 125,126,127 please see Oak 139,137,102 page 66 1 . Move the slide switch at the top of the remote to Pioneer 101,116 for a Scientific Atlanta 112,113 complete the product you want to control . Zenith 117,100 listing . 2 . Press and hold the POWER button on the remote To reset to default code , enter 000 control . Figure 1 . Programming the remote to control your cable 3 . Enter the first three digit code listed for your box . equipment , and then release the POWER button on the remote control . 4 . Point the remote control to the equipment and press the POWER button . Note : If the equipment responds , the remote control is CABLE / DBS / DT _ VCR DVDt - TVt _ $ _ AUDIO properly programmed to operate the equipment . If _ i lit I . the equipment does not respond , repeat steps 2 - 4 1 . _ ( [ tt ] ) ) with the next three digit code listed in step 3 for 1 your equipment . Satellite brand Codeto enten If your 006 satellite Mitsubishi DTV - DBS receiver DishNetwork 175 code is not 173 Hughes - DBS listed here , Panasonic - DBS 174 please see RCA - DBS 176 page 67 for 177 Sony - DBS a complete Toshiba - DBS 170 , 173 , 189 , 190 , 191 listing . To reset to default code , enter 000 Figure2 . Programming t ] aeremote to control your satellite receiven CABLE / DBS / DTV _ VCR DVD _ TV - o _ J , _ - AUDIO I IIII 1 . ( c m ) ) 1 VCR brand Codetoente _ If your VCR Mitsubishi 001,002 code is not Hitachi 020,043,065 listed here , JVC 030,054 3Iease see 043,044,051 Phillips / Magnavox page 67 Panasonic 041,042,043 fora RCA 020,053,065 complete 048,049,050 Sony listing . Toshiba 021 To reset to default code , enter 000 Figure3 . Programming t ] aeremoteto controlyour VCR . 27
Page: 28
Use of the Remote Control with Other A / V Products CABLE / DBS / DT _ VCR DVD After entering the correct codes in each position of the TV - 4 _ _ , _ e - AUDIO I III I remote control , use the dide switch to select which 1 . ( ( . ] ) 2 . product will respond when an operational button is m pressed . If you enter a code from the AUDIO chart DVD / LDP brand Code toen _ n If your while the slide switch is set to TV , the volume and DVD Mitsubishi OO3 code is not JVC 257 mute functions change to match the A / V receiver . listed here , Panasonic 25O please see This is useful when using an A / V receiver with the Philips 258,283,272 page 66 Pioneer DVD 252 TV all the time . In all other cases , only one of the for a 261 Samsunq complete 254 below devices is allowed for each slide switch position . Sony listing , Toshiba 253 To reset to default code , enter 000 TV position : Figure 4 . Programming the remote to cantrol yaur DYD or LDP . [ ] TV [ ] A / V receiver ( volume and mute only ) Cable / DBS / DTV position : CABLE / DBS ! D _ V _ VCR DVDe - [ ] Cable box TV - o J , / * _ AUDIO I I I I I [ ] Satellite receiver 1 . ( ( m [ ] DTV receiver 8 VCR position : Audio brand Codetoenter : i _ your [ ] VCR Mitsubishi AN receiver 010 , 015 , 011,012 , audio 3nd / or CD player 013 , 014 code is not 234,235,236,245 , listed here , Denon DVD position : 246.359 please see [ ] DVD Harman Kerdon 215 , 223 , 242 page 66 JVC for a 233,232 [ ] LD Player Kenwood complete 208.200 Marantz listing , 224,350 Dnkyo 209 , 214 , 240 , 247 Audio position : Pioneer 205,207 [ ] A ! V receiver Sony 222,249 Technics 218,219,221 [ ] Mitsubishi CD player Yamaha 202.201.243.244 To reset to default code , enter 000 If you have a Mitsubishi A / V receiver , the audio position may be used in conjunction with select Mitsubishi CD Figure 5 . Programming the remote to cantra / your players ' . Your audio position must beprogrammed to A / V receiver . either 010 or 011 . Plug the CD player power cord into a switched outlet on the back ofyour A / V receiver . Pressing the POWER button turns On the A / V receiver , along with the CDplayer . In the audio position , for some CD players , the transport controls ( FF , Play , Rew , etc . ) ofoemte the CD player . IMPORTANT 28
Page: 29
Remote Control Functions : Special Functions When your remote control has been Programmed to operate another manufacturer's product , the function performed on each layer may vary . The most common functions are : oMitsubishi VCRs will be com with additional buttons oPOWER • ENTER ( on some models ) oADJUST up / down / left / right ( on some models ) oCHANNEL up / down • CANCEL ( on some models ) • 0 - 9 Number Buttons ( on some models ) • GUIDE ( on some models ) oPOWER * VOLUME • MUTE oDirect Input Selection Buttons - use number buttons , SQV , and QV ( on some models ) ( on some • 0 - 9 Number Buttons 3n some Remote Control Functions : Operation of PIP and POP Activating the PIP and POP Picture - In - Picture ( PIP ) and Picture - Outside - Picture ( POP ) features allow you to view Programming in different ways . While watching Press PIWPOP to choose a display format . Each the main screen , you can display programs from time the PIWPOP button is pressed on the TV other channels and other inputs . To see which remote control ( within 3 seconds of each other ) , inputs can and cannot be used together , see How the PIP / POP cycles through the following display Connections Affect the PIP and POP , page 22 . options . You can display large and small PIPs , side - by - side 1 . POP : side - by - side pictures pictures , three POPs , or nine POPs . 2 . POP : three POPs 3 . POP : nine POPs 4 . PIP : large PIP 5 . PIP : small PIP To turn PIWPOP Off , wait at least 10 seconds , and press PIWPOR The next time you activate PIWPOP , the last used PIWPOP format will be displayed first . 29
Page: 30
IMPORTANT NOTES Warning : Do not leave stationary PIP / POP , or letterbox images on the screen for extended periods of time . Mix the types of pictures shown . Uneven picture tube aging is NOT covered by your warranty . The normal use of a TV should include a Examples of these types of images can be , but mixture of TV picture types . The most are not limited to the following : frequently used picture types should fill the screen with constantly moving images Letterbox top / bottom black bars : rather than stationary images or patterns . shown at the top and bottom of the TV screen Displaying the same stationary patterns over when you watch a widescreen ( 16 : 9 ) movie on extended periods of time or displaying the a standard ( 4 : 3 ) TV . same stationary pattern frequently can leave subtle but permanent ghost images . To avoid Side bar images : this , mix your viewing pattern and reduce the solid bars shown on each side of an image initial contrast level . Do not show the same when watching a standard ( 4 : 3 ) program on a stationary image for more than 15 % of your widescreen ( 16 : 9 ) TV . total TV viewing in any given week . Display constantly moving and changing images that fill the screen whenever possible . News and stock - market report bars : ticker running at the bottom of the TV screen . This projection TV uses picture tubes to project the image to the screen . All picture tubes age with Shopping channel logos & pricing displays : use . As they age , their light output is gradually bright graphics that are shown constantly or reduced . Normal TV pictures fill the screen repeatedly in the same location . with constantly changing images . Under these conditions , picture tubes age at an even Video game patterns and scoreboards rate across the entire screen . This maintains a TV picture that is evenly bright over the whole screen . Stationary images or images Bright station logos : that only partially fill the screen ( leaving black moving or low - contrast graphics are less likely or colored bars to fill the screen ) , when used to cause uneven aging of the picture tubes . over extended periods of time or when viewed repeatedly , can cause uneven aging of the Online ( Internet ) websites : phosphors and leave subtle ghosts from the or any other stationary or repetitive computer stationary images in the picture . style images , including digital photos Still or stationary images may be received from Closed Captioning broadcasters , cable channels , satellite channels , Mitsubishi recommends using a gray DVD discs , video tapes , laser discs , on - line background rather than black or a bright color services , web / Internet searching devices , video if you frequently use closed captioning . games , and digital TV tuner / converter boxes . 3O
Page: 31
4 V - CHIP LOCK Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 ADVANCED FEATURES Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 AUDIO / VIDEO SETTINGS Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Page: 32
The i poAnMAenu System Your TV has Mitsubishi's exclusive _ [ " on - screen operating system , which provides on - screen information for menu choices and changes . A picture ( icon ) will be highlighted and can be selected using the remote control's ADJUST arrows . When selected , the appropiate menu will appear or start an automatic function . You may then make changes within the menu or access available sub - menus . A highlighted square button indicates that you may make changes to the menu screen . The _ R ® system includes the following special features : [ ] The currently selected icon or button is highlighted with a rectangular yellow outline and the text color will be yellow . [ ] On - screen instructions provide complete menu Figure 1 . MAINmenu : choice information . The first screen that appears when you press the [ ] Some on - screen menu options must be set before MENU button from your remote . other options are available . For example , " Timer Menu " will only be possible if " Clock Time " and " Set Day'have been set . The following remote control buttons will help you move quickly through the _ 1 _ ® system ( Figure 2 ) : ADJUST • or • to select the menu item you want to change . ADJUST • to move to the setting field . ADJUST • or • to change the settings . ADJUST _ to move back to the menu item . Figure2 . These buttons on your remote ENTER to enter into a menu , start an automatic control are used for navigation within the function , or select a checkbox . on - screen operating system . CANCEL to clear a setting , or stop an automatic function . MENU to move back one menu screen at a time . HOME to exit all menus at once and return to TV viewing . 32
Page: 33
Main Menu Screens : Overview SETUP Menu ( Figure 3 ) Basic ( initial ) setup instructions and functions are available through the SETUP submenu screens . • Memorize channels , • Assign Input Assignments • Set the time and day • Select English or Spanish for the menus or screen display • Set the Front Button Lock ( WT - 42313 ) • Set the Energy Mode ( WS - 48313 , WS - 55313 or WS - 65313 ) . Figure3 . SETUP menu for WS - 48313 , WS - 55313 , WS - 65313 Use the setup menu when you relocate the TV , experience a power loss or when devices are added after initial setup . See pages 35 - 39 for more detailed setup information . CAPTIONS Menu ( Figure 4 ) Display broadcasted captions or text on the screen . Select the closed caption setting by choosing to display the background color as either black or translucent gray . See pages 40 - 41 for more detailed setup information . Note : Mitsubishi recommends using the translucent Figure 4 . CAPTIONS menu gray background to prevent CRT aging and / or burn - in . CHANNEL EDIT Menu ( Figure 5 ) • Customize the channel information for Ant - A and Ant - B , • Manually add or delete channels from memory • Name channels for Ant - A and Ant - B • Add your favorite channels to a SQV ( Super Quick View " _ ) list . See pages 42 - 44 for more detailed setup information . Figure 5 . CHANNEL EDIT menu ( ANTENNA ) 33
Page: 34
Main Menu Screens : Overview , continued V - CHIP LOCK Menu ( Figure 6 ) Lock the TV by selecting times or choosing programs to block based on rating signals sent by your local broadcasting system . NOTE : ForWS - 48313 , WS - 55313 orWS - 65313 set the Front Button Lock at this screen . See pages 46 - 49 for more detailed setup information . See page 45 for V - Chip rating information . Figure6 . V ChipLockMenu , WS - 48313 , WS - 55313 , WS - 65313 ADVANCED FEATURES Menu ( Figure 7 ) • Adjust colors automatically or manually , using Color Balance • Set your TV to turn on automatically • Converge ( align ) the three main colors • Display a blue screen when viewing an input with no signal • Enhance the darker parts of bright pictures See pages 50 - 54 for more detailed setup information . Figure 7 . ADVANCED FEATURES Menu AUDIO / VIDEO SETTINGS Menu ( Figure 8 ) Adjust some or all of the A / V settings . Each input can be set to your preferences . A / V Reset on the menu allows you to return the A / V settings for the current input to the factory presets . A / V Reset on the front control panel resets all inputs at one time . See pages 55 - 57 for more detailed setup information . Figure8 . Audio / VideoSettingsMenu 34
Page: 35
SETUP Menu : Memorize Channels , Memorize Menu , Input Assignment Memorize Channels ( Figure 9 ) Select Memorize Channels for each antenna you use . The TV will find and remember strong channels and skip the unused or weaker channels . Figure 9 . Memorize Channels Menu MEMORIZE Menu ( Figure 10 ) Stop memorization at any time by pressing CANCEL . Channels memorized prior to pressing CANCEL will stay in memory . After channels are memorized , Now m _ mor ± zing all _ e _ tations you may select memorized channels in ascending or you can recei _ on _ t - A Ai _ . Please _ tand by . descending order by pressing the CHANNEL button on the remote control . INPUT ASSIGNMENT Menu ( Figure 11 ) Figure lO . Memorize Menu INPUT ASSIGNMENT turns offunused inputs , turns them on again or changes the name of the input . If you turn an input Off , it will be skipped when you press INPUT on the remote control . Choices are : [ ] ANT - A , ANT - B : On or Off [ ] DTV : Y / Pb / Pr , RGB , RGBHV or Off [ ] COMPONENT ( S ) * Cycle through a list of preset names or Off [ ] INPUT - l , INPUT - 2 , INPUT - 3 : Cycle through a list of preset names or Off [ ] MonitorLink ( MONLINK ) Cycle through a list of preset names or Off * COMPONENT - 2 is not available for WT - 42313 Figure 11 . Input _ / lssignment Menu WT - 42313 35
Page: 36
SETUP Menu : Manually Setting the Clock Clock Setting ( Manual ) ( Figure 12 ) The Clock Setting menu default allows the clock time to be set manually . To set the clock automatically , please see page 37 . To set the clock manually , first select the current time , including AM or PM . Press • or V to slowly adjust the time . Press and hold • or • to quickly adjust the time . Figure 12 . Clock Time Set Day ( Figure 13 ) After manually selecting the current time , select the current day . Figure l3 . Set Day 36
Page: 37
SETUP Menu : Automatically Setting the Clock Clock Setting ( Auto ) ( Figure 14 ) Set the Clock Setting to Auto to automatically set the day and time using Extended Data Service ( XDS ) time data . This data is automatically retrieved when tuned to a PBS channel or other channel in your area that provides this service . Time Zone ( Figure 15 ) Select the correct time zone ( Atlantic , Eastern , Central , Mountain , Pacific , Alaska , or Hawaii ) for your area when Auto has been selected as the Clock Setting . Figure 15 . Time Zone Daylight Savings Time ( Figure 16 ) Select the Daylight Savings Time ( DST ) option that your state uses when Auto has been selected for the Clock Setting . Applies = uses DST Ignore = does not use DST The clock time and day will be set automatically after tuning to a channel carrying the Extended Data Service ( XDS ) time data ( usually your local PBS channel ) . Figure 16 . Daylight Savings Time 37
Page: 38
SETUP Menu : Language , Front Button Lock ( WT - 42313 ) Language ( Figure 17 ) Display the on - screen menus in either English or Spanish ( Espafiol ) . The first time you powered On your TV , you were requested to select an on - screen menu language . If you choose to change the selection , all menu text will immediately switch to the language of your choice . Figure 1Z Language / Idioma Front Button Lock for WT - 42313 ( See V - Chip Menu for other models ) ( Figure 18 ) Disable controls on the front panel to prevent anyone from accidentally changing settings . Select On to lock out the operations of the front panel button and select Off to restore the operations of the front panel buttons . If the front panel buttons have been locked and you misplace the remote control , you can restore the function of the front panel buttons by pressing and Figure 18 . Front Button Lock for WT - 42313 holding the MENU button on the front panel for more than 8 seconds . If the TV is already on , a message will be displayed to confirm the release of the Front Button Lock . 38
Page: 39
SETUP Menu : Energy Mode ( WS - 48313 , WS - 55313 , WS - 65313 ) Energy Mode ( Figure 19 ) This feature is only for models WS - 48313 , WS - 55313 and WS - 65313 . Change the setting to Low ( less than 1 watt ) and the TV will operate in an energy saving mode when it is turned off . If the Energy Mode is set to Low , it w'dl not be possible to record while the TV's power is off because there will be no signal from LOOP OUT ( on the TV back panel ) to the VCR and / or cable box . Figure 19 . Energy Mode for W8 - 48313 , W8 - 55313 , WS - 65313 NOTE : The Standard setting has a faster turn on time , but uses more power than the Low setting . Standard is recommended . 39
Page: 40
CAPTIONS Menu : Overview CAPTIONS Menu ( Figure 20 ) Turn On or Off the closed caption decoder , select the type of captions or text , and choose black or translucent gray as the background color for the closed caption area . Broadcasters can send either Standard or Text closed captioning . Standard closed captioning follows the dialogue of the characters on - screen and displays in a small section of the screen . Figure20 . CAPTIONS menu Text closed captioning often contains information such as weather or news and covers a large portion of the on - screen program . Your TV can decode four different standard and four different text closed captioning signals from each TV station . However , each TV station may broadcast only one or two closed captioning signals , or none at all . 40
Page: 41
CAPTIONS Menu : Closed Captions , Background Color Closed Captions ( Figure 21 ) Display one of the following types of Closed Captions : CC1 , CC2 , CC3 , or CC4 : Standard closed captioning signals . _ . Textl , Text2 , Text3 , or Text4 : Text dosed captioning signals . _ . On if mute : Closed captions when mute . When selected , the standard dosed captioning signal ( CC1 ) will turn on / off by pressing the MUTE button on the TV remote control . _ . Off : No dosed captions . Figure 21 . Closed Captions CC Background ( Figure 22 ) Display the background color as either black or translucent gray , to make the closed captions easier to read . Note : Mitsubishi recommends using the translucent gray background to prevent CRT aging and / or burn - in . Figure22 . CAPTIONS menu 41
Page: 42
CHANNEL EDIT Menu : Antenna , Channel Selection Antenna ( Figure 23 ) Select Ant - A or Ant - B . For each antenna , you can add or delete channels in memory , name channels , and add channels to the SQV ( Super Qgick View TM ) list . Figure23 . An _ nna Channel ( Figure 24 ) Select to edit the channel selections . You can add or delete from memory , name , or add to the SQV ( Super Qgick View TM ) list . After selecting Channel , editing can be done using the Adjust buttons or entering the 3 digit channel number you want to change ( Example 002 for channel 2 ) . Figure24 . Channel 42
Page: 43
CHANNEL EDIT Menu : Memory , Name Selection Memory ( Figure 25 ) Add weaker channels viewed with Ant - A or Ant - B and delete unwanted channels , after all available channels have been memorized with Memorize Channels ( page 35 ) . Use the CH ( channel ) button on the remote control to view memorized channels . Figure25 . Memory Name ( Figure 26 ) Name channels shown on Ant - A or Ant - B ( up to four characters ) . After you enter a name , it will appear on the TV screen next to the channel number . 1 . Select Ant - A or Ant - B . 2 . Select the memorized channel you want to name . 3 . Press ADJUST until you see the underline highlighted in the Name field . 4 . Use ADJUST • or • to select letters A - Z , numbers 0 - 9 , and ! or symbols ( ! . & ' ! : * - and blank ) for each character of the name you would like for the selected channel . Dess ENTER after choosing each letter and after the name is complete . If you want to change your selection while on the option Figure26 . Name field , use CANCEL to delete the currant character . You will move one position back . If you press CANCEL while at the first character , the entire name will be deleted . 43
Page: 44
CHANNEL EDIT Menu : Using SQ . V ( SuperQuickViewTM ) Using The Menu Screen ( Figure 27 ) Put together a list of your favorite channels from Ant - A and Ant - B using SQ _ V ( Super Q _ ick View ) . Store up to 6 channels in each of the 9 different memory banks . After adding a channel to the SQV memory , " SQ _ V " will appear under the channel number on the TV screen . To change SQV choices using the menu : 1 . Press A or • when at Channel settings or use the CHANNEL button on the remote control to select the channel you wish to add or delete from a SQV Figur _ 2z SQV ( Su ? erQ _ , i _ zki _ ' M ) memory bank . 2 . Press II , when at SQV in the menu to move the selector to the On ! Off setting . 3 . Press A or • when at SQV setting to select the SQV memory bank you wish to modify . 4 . Dess ENTER to add ( On ) or delete ( Off ) the current channel from the SQV memory bank that you have selected . Figure 28 . SQV ( Super Quirk View rM ) but / on on the remote control Using The Remote Control ( Figure 28 ) View and add so . y channels using the remote control : 1 . Use the CH ( channel ) or number buttons to select the channel you want to add . 2 . Dess and hold the SQV button for about 3 seconds . When " SQV " and the memory bank number appear under the channel number , the channel has successfully been added . To change the sO . y banks using the remote control : 1 . Press the SQV button . 2 . To change memory banks , press a number button within 5 seconds of pressing the SQV button . Remove so . y channels using the remote control : 1 . Press the SQV button repeatedly until you see the desired channel . 2 . While the channel number and SQV indicator am still displayed on the screen , press the CANCEL button . If the CANCEL button is not pressed before the SQV indicator disappears , the channel will not be removed . 3 . When the SQV indicator disappears , the channel has successfully been removed . 44
Page: 45
V - CHIP LOCK Menu : Overview V - Chip Signal Information When provided by the broadcaster , V - Chip ratings can be used to control which programs can be viewed or will be blocked . When V - Chip ratings are sent , you will see the ratings when you change the channel or when you press the INFO button on the remote control . Both TV and Movie ratings will display . TV ratings apply to programs and movies developed for TV and may have supplemental blocking by content categories . Movie ratings use MPAA ratings for movies released in theaters . V - CHIP EXCEPTIONS : TV Ratings : Used with TV programs and Made - for - TV movies . TV Rating FV D L S V TV - Y Youth , for children under the age of 7 . TV - Y TV - Y7 Youth , 7yearsoldandolder . b _ rchildren7yearsoldandolder . TV - Y7 X TV - G General Audience . For the entire family to view . TV - PG X X X X TV - PG Parental Guidence . Parental Guidence is recommended , may not be suitable for some children . TV - 14 X X X X TV - 14 Addescent 14years dd and alder . Not recommended for children TV - MA X X X under the age of 14 . TV - MA Mature Audience . For adults only . Content Categories : Used in association with the TV ratings above . FV Fantasy Violence - applies to TV - Y7 only . D Sexual Dialog - applies in different degrees to TV - PG and TVq4 . L Adult Language - applies in different degrees to TV - PG , TVq4 , and TV - MA . S Sexual Situations - applies in different degrees to TV - PG , TVq4 , and TV - MA V Violence ( graphic or realistic ) - applies in different degrees to TV - PG , TVq4 , and TV - MA . When you select a TV rating , you are selecting the least - restriced program level that can be viewed . As an example , if you select TV - PG , you are allowing programs rated TV - Y , TV - Y7 , TV - G and TV - PG to be seen and blocking programs rated TV - 14 and TV - MA . When you select a TV Content category , you will block all TV programs that have the same content category listing . As an example , if you select to block V ( Violence ) at the TV - 14 level , you will also block any program that has the V category listing at the TV - PG rating level as well . Movie Ratings : Used with theater released movies and direct - to - video movies . G General Audience - Designed for the entire family m view . PG Parental Guidence - Parental Guidence is recommended , may not be suitable for some children . PG - 13 Parental Guidence 13 years dd and older - Not recommended for children under the age of 13 . R Restricted - Restricted in the theater to 17years old and older unless accompanied by an adult . NCq7 No Children - Restricted in the theater to 18 years dd and older . X Adult - Designed for and restricted in the theater m adult audiences only . When you select a Movie rating , you are selecting the least restricted program level that can be viewed . As an example , if you select a movie rating of PG - 13 , you are allowing movies rated G , PG and PG - 13 to be seen and blocking movies rated R , NC - 17 , and X . Programs Not Rated : Used for programs that are not rated like news , sports , weather , emergency bulletins , or movies such as those prior m or without MPAA Ratings . This does not include programs without V - Chip signals 45
Page: 46
V - CHIP Menu : Setting Up and Using V - Chip Lock Passcode Setting Up the V - CHIP LOCK Passcode ( Figure 29 ) Select V - CHIP LOCK from the MAIN menu for first time setup or after you have canceled your passcode . You will see the screen shown in Figure 29 . Use the number buttons on the remote control to input a new four - digit passcode , then press ENTER . Before pressing ENTER , you can delete a character and move back one character by pressing CANCEL , Figure29 . First time entry to the V - CHIP LOCK all or leave the passcode screen by pressing MENU or models HOME . Entering the Passcode ( Figure 30 ) Input your passcode as shown in Figure 30 ( Note : Text changes from " a new " to " your " passcode ) . The next time you select V - CHIP LOCK from the MAIN menu , you will see this screen . Figure 30 . Re - entry to the V - CHIP LOCK all models 46
Page: 47
V - CHIP Menu ( WT - 42313 ) : Allowing or Blocking Ratings , Locking by Hour or Time Allowing or Blocking by Ratings ( Figure 31 ) Block or Allow programs based upon rating signals sent by the broadcasting station . The factory preset for TV Ratings is TV - PG ( Parental Guidance ) allowing only programs rated TV - PG or lower . The factory preset for Movies is PG , allowing only movies rated PG or lower . Please refer to page 45 for a detailed ratings description . Figure 31 . V - CHIP LOCK Choices WT - 42313 V - CHIP HOURS / LOCK BY TIME ( Figure 32 ) V - CHIP HOURS / LOCK BY TIME will allow you to activate the V - Chip or lock the entire TV during specific hours . V - CHIP Start Time and V - CHIP Stop Time ( Figure 32 ) Select the times you would like the V - Chip to be Active . By setting the V - Chip Start Time and V - Chip Stop Time to the same time , the V - Chip will be active 24 hours a day . Press A or • to slowly adjust the time . Press and hold A or • to quickly adjust the time . Figure 32 . V - CHIP HOURS / LOCK BY TIME WT - 42313 Lock by Time , Lock Time , and Unlock Time ( Figure 32 ) Lock by Time locks the entire TV when Lock by Time is On and you have selected a Lock Time and Unlock Time . Your TV continues to be locked until you input your passcode , or when the locked time expires . 47
Page: 48
V - CHIP Menu ( WS - 48313 , WS - 55313 , WS - 65313 ) : Locking by Time , Front Button Lock , Selecting V - Chip Rating Menu LOCK by Time ( Figure 33 ) Select On at Lock by Time , then select the Lock Time and Unlock Time . This will lock the entire TV . Your TV continues to be locked until you input your passcode , or when the locked time expires . Front Button Lock ( Figure 34 ) Setting the Front Button Lock to On will disable Figure33 . V - CHIP LOCK Menu Lock by Time controls on the front panel to prevent anyone from accidentally changing settings . Offwill restore the operations of the front panel buttons . If the front panel buttons have been locked and you misplace the remote control , you can restore the function of the front panel buttons by pressing and holding the MENU button on the front panel for more than 8 seconds . If the TV is already on , a message will be displayed to confirm the release of the Front Button Lock . Selecting V - Chip Rating Menu Figure 34 . Front Button Lock ( Figure 35 ) To block or allow programs based on the rating system described on page 45 , select V - Chip to go to the V - Chip Rating menu . Figure 35 . Selecting V - Chip Rating Menu 48
Page: 49
V - CHIP Menu ( WS - 48313 , WS - 55313 , WS - 65313 ) : Allowing or Blocking Ratings , Lock by Time Allowing or Blocking by Ratings ( Figure 36 ) Block or Allow programs based upon rating signals sent by the broadcasting station . The factory preset for TV Ratings is TV - PG ( Parental Guidance ) allowing only programs rated TV - PG or lower . The factory preset for Movies is PG , allowing only movies rated PG or lower . Please refer to page 45 for a detailed ratings description . V - CHIP HOURS ( Figure 26 ) Figure 36 . Ratings Menu , WS - 48313 , WS - 55313 , V - CHIP HOURS will allow you to activate the V - WS - 65313 Chip or lock the entire TV during specific hours . To set V - Chip Hours , select V - CHIP Hours from the V - CHIP LOCK menu . V - CHIP Start Time and V - CHIP Stop Time ( Figure 37 ) Select the times you would like the V - Chip to be Active . By setting the V - Chip Start Time and V - Chip Stop Time to the same time , the V - Chip will be active 24 hours a day . Press A or • to slowly adjust the time . Press and hold A or • to quickly adjust the time . Figure 3Z Selecting V - Chip Rating Menu WS - 48313 , WS - 55313 , WS - 65313 49
Page: 50
ADVANCED FEATURES Menu : Color Balance , Auto Color Correction , PerfectColor xM , Reset Color Color Balance Menu ( Figure 38 ) Your Mitsubishi TV uses six colors ( Magenta , Red , Yellow , Green , Cyan and Blue ) to create Color Balance . You may adjust these colors automatically or manually or reset them to the default settings . Auto Color Correction ( Figure 39 ) Set the Auto Color Correction option to On to optimize skin tone color automatically and continuously . Both Manual Color Adjustment and Reset Color options are grayed out and unavailable when On is selected for Auto Color Correction . Figure 38 . ADVANCED FEATURES MENU PerfectColor ( Figure 40 ) Press ENTER to display the menu for manual color adjustment . Individual sliders for Magenta , Red , Yellow , Green , Cyan and Blue will be displayed . The sliders have a numeric value , where 63 is the maximum . The default setting for each color is 31 ( center ) . Highlighted text will show which slider you are adjusting . • For WT - 42313 all inputs are adjusted at once . This feature is available only with the 480i signal . • For WS - 48313 , WS - 55313 or WS - 65313 , each active input can be individually adjusted . Figure 39 . COLOR BALANCE Menu Press Adjust • or V to navigate between colors and Adjust _ or _ , to change the color slider settings . The PerfectColor option is only available when Auto Color Correction is turned Off . Reset Color ( Figure 39 ) Select to reset the PefectColor settings . • For WT - 42313 all inputs are reset at once . This feature is available only with the 480i signal . Figure 40 . PerfectColor Menu • For WS - 48313 , WS - 55313 or WS - 65313 , each active input can be individually reset . 50
Page: 51
ADVANCED FEATURES Menu : TIMER , Timer Menu , and Set Time TIMER ( Figure 41 ) The timer will automatically turn the TV on ( if it is off ) at the time you schedule and select . When Ant - A or Ant - B is the selected input , you may select any memorized channel . The TV will tune to this channel when the timer turns it on . Figure 41 . ADVANCED FEATURES menu TIMER menu ( Figure 42 ) The timer can be turned On or Off . When On , you need to select the time and the day to turn On and the input and channel to display . At your preselected time , the timer will turn the TV on and a message will be displayed , " Press a key for the TV to stay on . " Any button on the remote control must be pressed within 5 minutes or the TV will turn itself off . Figure 42 . TIMER menu ( Timer ) Set Time ( Figure 43 ) Select the hour and minute , including AM or PM , when the TV is to turn on . Press • or • to slowly adjust the time . Press and hold • or • to quickly adjust the time . Figure 43 . TIMER menu ( Set Time ) 51
Page: 52
ADVANCED FEATURES Menu : Set Day , Input , and Channel Set Day ( Figure 44 ) Select the days that the TV will turn on automatically . You can select Everyday , Mon - Fri ( Monday through Friday ) , or the individual days of the week . Figure44 . TIMER menu ( Set Day ) Input ( Figure 45 ) Select the input to use when the timer turns on the TV . If the TV is already on , the timer will turn the TV to this selected input . Figure45 . TIMER menu ( Input ) Channel ( Figure 46 ) If the selected input is for Ant - A or Ant - B , the timer will turn the TV to the selected channel . Figure46 . TIMER menu ( Channel ) 52
Page: 53
ADVANCED FEATURES Menu : CONVERGENCE CONVERGENCE Menu ( Figure 47 ) Your Mitsubishi TV has three picture tubes which are aligned to properly converge the projected light beams on the screen . Each picture tube projects a single color of red , blue or green . During production , your TV was carefully adjusted to properly align these colors . As a special feature , you have the ability to adjust the red and blue light beams in reference to the fixed green light beam . This process is called convergence . Convergence aligns the entire screen at once . Select either Red Convergence or Blue Convergence to begin alignment . Figure 4Z CONVERGENCE menu Convergence Screen ( Figure 48 ) When the Red and Blue crosshairs are properly converged , the center - screen crosshairs will appear white . You can use A , V , ' , or • to move the Red and Blue crosshairs . Press VIDEO to switch between Red and Blue . Press AUDIO for the Advanced Convergence screen . Advanced Convergence ( Figure 49 ) After adjusting the Red Convergence and Blue Figure 48 . Convergence screen Convergence , you can fine - tune your TV by adjusting the Red and Blue convergence at 64 individual points . Move the flashing bracket to a position needing adjustment by pressing A , V , ' , or • . Press ENTER to select the position ( flashing will stop ) . Move the Red or Blue line by pressing A , V , _ , or • . Press VIDEO to switch between the Red and Blue lines . A position is properly converged when all three lines combine to appear white . Press ENTER to deselect the position ( flashing will resume ) , and move the brackets to the next position needing adjustment . When completed , press MENU to save your changes , and exit the Advanced Convergence screen . NOTE : This is considered a fixed image . Please see Important Notes on page 6 , 12 or 30 . Figure 49 . Advanced Convergence screen 53
Page: 54
ADVANCED FEATURES Menu : Reset Convergence , Video Mute , Black Enhancement RESET FACTORY DEFAULTS ( Figure 50 ) If you do not want to reset the convergence , press the MENU key to return to the Convergence menu without performing a reset . You may reset the red and blue convergence to factory default settings when you first use your TV or after making manual changes . Press the ENTER key to restore the convergence to the default settings . All the changes you made manually will be deleted . The Figure50 . RESET to Factory Defaults message " Convergence Completed " appears when the convergence reset process ends . Video Mute ( Figure 51 ) Video Mute , when On lets you display a blue background when no signal is being received on Inputs 1 - 3 , DTV , and Component 1 - 2 ( Component only for WT - 42313 ) and MonLink . FigureS1 . Video Mute Black Enhancement ( Figure 52 ) The contrast in dark scenes is enhanced for better picture quality . Brighter scenes will not be affected . ig _ e 52 . Black Enhancement
Page: 55
AUDIO / VIDEO SETTINGS Menu : Overview AUDIO / VIDEO SETTINGS Menu ( Figure 53 ) Each input has its own A / V memory . You can adjust each input's A / V memory in two ways . You can use the menu or the remote control . A / V Memory Reset A / V Memory Reset will return the currently selected input's A / V memory to the factory settings . To reset an input's A / V memory , select A / V Memory Reset , select the input you want to reset , and press ENTER . TV Speakers This selection will turn on or off the TV _ internal Figure 53 . AUDIO / VIDEO SETTINGS menu speakers . You may select Offwhen sending the sound through a separate stereo system or surround sound A / V receiver . Audio Output Select Fixed if your audio receiver or stereo system can be controlled with a remote . This allows you to adjust the volume with the system's remote control or the TV remote control , if compatible . This setting is better for surround sound receivers . Select Variable if your audio receiver or stereo system cannot be controlled with a remote . This allows the TV's internal circuitry to adjust the volume . AUDIO SEq _ NGS and VIDEO SEq _ NGS ( Audio Settings , Figure 54 ) After selecting AUDIO SETTINGS or VIDEO SETTINGS , you can adjust the settings by pressing A , V , I , or • . For descriptions of the individual A / V settings , see AUDIO / VIDEO Setting Descriptions , pages 56 - 57 . Figure 54 . AUDIO SETTINGS Using the AUDIO and VIDEO Buttons on the Remote Control 1 . Press AUDIO or VIDEO to cycle through the available settings . 2 . Press _ or • to adjust the setting . After 5 seconds of inactivity , the setting display will disappear . 55
Page: 56
AUDIO / VIDEO Setting Descriptions : Audio signal is broadcast , the letters " SAP " will be Audio Settings displayed when you tune to the channel . [ ] Bass • Mono : Reduces background noise and should Enhances or reduces low frequency sound . be used when receiving a weak stereo audio [ ] Treble signal . All audio will be played mono with Enhances or reduces high frequency sound . this setting . [ ] Balance [ ] Listen to ( for INPUTs ) Is not available . Adjusts the level of sound between the left and right speakers . [ ] Level Sound [ ] Surround Automatically equalizes the volume level Creates simulated stereo and surround effects . of programs containing significant level Your choices are : differences from one segment to another ( for example , regular programming to • Off : No surround effects . Use this setting commercials ) . To receive the best fidelity with when using an A / V receiver with Dolby " rM music programs , you can turn this setting to Pro Logic Surround , or Dolby TMDigital Off . Surround . • Simulated Stereo : Your TV will create a NOTE : A slider will display on - screen for each simulated stereo effect when watching a non - setting . The slider has a numeric value , where 63 is stereo program . the maximum , the mid - range is 31 and the minimum • Surround Sound : Your TV will create a setting is 0 . simulated surround effect when watching a stereo program . [ ] Listen to ( for Ant - A and Ant - B ) Determines how your TV will receive a broadcast audio signal and play back the sound you hear . Your choices are : Stereo : Default setting . The TV will play stereo broadcasts in stereo and mono broadcasts in mono . The word " Stereo " will be displayed when you tune to a channel broadcasting stereo . SAP ( Second Audio Program ) : Additional monaural soundtrack that you cannot hear during normal TV viewing . The SAP signal might be related to the program you are watching , such as a soundtrack in a foreign language , or unrelated to the program you are watching such as a weather report . If a SAP 56
Page: 57
AUDIO / VIDEO Setting Descriptions : Video [ ] Film Mode ( Automatic ) Video Settings Video media uses a video camera created at [ ] Contrast 30 frames per second . Film media uses a Provides a slider to adjust the white - to - black film camera created at 24 frames per second . level . Low contrast shows a variety of shades Examples of video media are live TV broadcast in darker images , while high contrast shows such as news , special events , or video taped darker images more uniformly black and programs . Examples of film media are makes colors appear more vibrant . motion pictures , made - for - TV movies , and many prime time programs . Filmed media is [ ] Brightness converted by the broadcaster or home video Provides a slider to adjust the overall company to 30 frames per second to match TV brightness of the picture . or video standards . This conversion can leave [ ] Sharpness subtle " picture artifacts " or conversion errors . Provides a slider to adjust the detail and clarity . The settings are On and Off . If you select On , the system automatically detects if the signal [ ] Color source is Film and corrects for conversion Provides a slider to adjust the color intensity . errors . If you select Off , the system will never [ ] Tint correct for conversion errors . Provides a slider to adjust the proportion of red This function operates only in 480i mode . to green . [ ] Color Temp ( Color Temperature ) Allows you to adjust how white images are displayed . Your choices are : NOTE : A slider will display on - screen for each setting . The dider has a numeric value , where 63 • Low 6500K or Low ( for DTV ) : White is the maximum , the mid - range is 31 and the images will have a warm cast to them . This minimum setting is 0 . adjustment is an average and can vary due to ambient room lighting , video scene brightness NOTE : For optimal picture performance , it is and the TV's age . The Low 6500K represents recommended that you adjust your video settings the 6500K industry standard for NTSC ( non - ( specifically contrast and brightness ) during initial DTV ) pictures . setup . Certain factors will affect your personal • Medium : White images will be balanced preferences , including room lighting , glare reflections between the Low ( warm ) and High ( cool ) and viewing angles / distance . This also slows settings . phosphor aging . • High : White images will have a cool cast to them . This setting may provide the most realistic picture under bright lighting . Video Noise Reduces minor noise ( graininess ) in the broadcast or input signal . This function operates only in 480i mode . 57
Page: 58
58
Page: 59
Available On - Screen Format Sizes Format ( picture shape ) availability based on Input / Signal Stretch Plus Expand Expand HD INPUTS Standard 1080i Zoom Stretch Narrow 4 _ Op Ant - A 000 YES YES NO YES YES YES YES YES NO YES YES YES Ant - B 000 YES YES NO YES YES YES DTV ( 480i / 480p ) YES NO YES NO NO NO DTV ( 108 % YES YES NO YES YES YES Input - 1 YES YES NO YES YES YES Input - 2 YES YES NO YES YES YES Input - 3 YES YES NO YES YES YES Component - 1 or 2 ( 480i / 480p ) YES NO YES NO NO NO Component - 1 or 2 ( 10800 DVl ( 4801 / 480D / YES YES NO YES YES YES YES NO YES NO NO NO DVI ( 1080i ) NOTE : You can find aspect ratios on the back of most DVD covers . Also , Anamorphic DVDs are usually marked " Anamorphic " or " Enhanced for 16 : 9 TVs . " [ ] Standard ] Zoom Default format for DTV and Component Input Enlarges the picture , cropping some of the image displays a full - screen format . The Standard at each side , top and bottom . The Zoom format format displays Anamorphic DVDs that have is useful to remove or reduce the black top and the 1.78 : 1 or 1.85 : 1 aspect ratios . However , bottom bars on Anamorphic DVDs with 2.35 : 1 Anamorphic DVDs that have the 2.35 : 1 aspect aspect ratio . Note : This format is not available in the 1080i ratio still display black bars at the top and bottom of the screen , while narrow ( 4 : 3 ) images are signal . stretched evenly from side to side . [ ] Stretch [ ] Expand ( 480i / 480p ) Default format for Ant - A and Ant - B , and Inputs Enlarges the picture , cropping some of the image 1 - 3 . The Stretched format stretches narrow at the top and bottom . The Expand format is 4 : 3 images across the screen , however , there is useful to reduce the letterbox top and bottom less stretch in the center than the sides . bars of non - Anamorphic DVDs or to correct Note : Stretch is not available in the 1080i format . narrow 4 : 3 images that have been stretched in the Standard format . Note : Expand is not available in the 1080i format . [ ] Stretch Plus ( not available on WT - 42313 ) Similar to stretch mode , however to minimize distortions on the side , the picture is expanded to [ ] HD Expand ( 1080i ) crop off portions of the top and bottom . Useful Enlarges the picture , cropping some of the image when no important information is shown at the on both sides . This Expand format is useful top and / or bottom of the screen . to remove or reduce black side bars on HD broadcasts of 4 : 3 images with black bars ( See page 64 ) . ] Narrow Note : Expand HD is only available in the 1080i Displays narrow 4 : 3 images in their original format . shape and adds stationary gray side bars to fill the screen . Caution should be observed when using the Narrow format due to the stationary gray side bars . Note : This format is not available in the 1080i signal . 60
Page: 60
Available On - Screen Format Sizes , continued Widescreen Picture ( 16 : 9 - HD 1080i only ) Example : A True HD Broadcast Standard ( Recommended ) Expand ( Recommended for 4 : 3 images with Black Side Bars ) Widescreen Picture ( 480i1480p ) ; tandard ( Recommended ) Stretch Zoom ( For letterbox 2.35 : l DVDs ) Narrow ( Not Recommended ) Stretch Plus ( not available on WT - 42313 ) 61