Register / log-in to add to your Hammerwall Collection.
Manual Location
The Search Results for the Search Section to the left will appear here.
Page: 1
IRISKOFELECTIRICSHOCK DO NOTOPEN I • CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK , DO NOT REMOVE COVER OR BACK . NO USER SERVICEABLE PARTS INSIDE . REFER SERVICING TO QUALIFIED SERVICE PERSONNEL . The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of the presence of uninsulated " dangerous voltage " within the product's enclosure that may be sufficient magnitude to constitute a risk of electric shock . The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance ( servicing ) instructions in the literature accompanying the appliance . Warning : To avoid permanently imprinting a fixed image onto your TV screen , please do not display the same stationary images on the screen for more than 15 % of your total TV viewing in one week . Examples of stationary images are letterbox top / bottom bars from DVD disk or other video sources , side bars when showing standard TV pictures on widescreen TV's , stock market reports , video game patterns , station logos , web sites or stationary computer images . Such patterns can unevenly age the picture tubes causing permanent damage to the TV . Please see page 6 , 30 or 75 for a detailed explanation . Note : This equipment has been tested and found to comply with the limits for a Class B digital device , pursuant to part 15 of the FCC Rules . These limits are designed to provide reasonable protection against harmful interference in a residential installation . This equipment generates , uses and can radiate radio frequency energy and , if not installed and used in accordance with the instructions , may cause harmful interference to radio communications . However , there is no guarantee that interference will not occur in a particular installation . If this equipment does cause harmful interference to radio or television reception , which can be determined by turning the equipment off and on , the user is encouraged to try to correct the interference by one or more of the following measures : • Reorient or relocate the receiving antenna . • Increase the separation between the equipment and the receiver . • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected . • Consult the dealer or an experienced radio / TV technician for help . Changes or modifications not expressly approved by Mitsubishi could void the user's authority to operate this equipment . WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK , DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE . CAUTION : TO PREVENT ELECTRIC SHOCK , MATCH WIDE BLADE OF PLUG TO WIDE SLOT , FULLY INSERT . NOTE TO CATV SYSTEM INSTALLER : THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO ARTICLE 820 - 40 OF THE NEC THAT PROVIDES GUIDELINES FOR THE PROPER GROUNDING AND , IN PARTICULAR , SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING , AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL .
Page: 2
Contents Chapter 1 Television Overview Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Thank you . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Unpacking your New TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Special Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 NetCommand _ 1R for WS - 48413 , WS - 55413 , WS - 65413 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Front Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Back Panel Input / Output for WS - 48413 , WS - 55413 , WS - 65413 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Side Panel Input / Output for WT - 42413 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Chapter 2 Connections Connecting an Antenna or Wall Outlet Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Connecting an Antenna to a Cable Box or VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Connecting an Antenna to a Cable Box and VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Connecting Audio Components to a Cable Box or VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Connecting an Audio Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Connecting a DVD Player or Other S - Video Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Connecting a DTV Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Connecting MonitorLink ' _ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Connecting NetCommand _ IR Emitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 How Connections Affect the PIP and POP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Chapter 3 Remote Control Functions Overview of the TV Layer Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Care and Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Use With Other A / V Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Special Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Operation of P1P and POP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Chapter 4 Menu Screen Operations The ViewPoinff Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 MAIN Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 SETUP Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 CAPTIONS Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 CHANNEL EDIT Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 V - CHIP LOCK Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 ADVANCED FEATURES Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 AUD10 / VIDEO SETTINGS Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Chapter 5 Format Sizes , PIP / POP Operations , Appendices , Troubleshooting Available On - Screen Format Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Operation of PlP and POP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Appendix A : Bypassing the V - Chip Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Appendix B : HD Input Connection Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Appendix C : Remote Control Programming Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Appendix D : Cleaning and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Appendix E : Diamond Shield ' _ Installation and Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Page: 3
IMPORTANT SAFEGUARDS Please read the following safeguards for your TV and retain for future reference . Always follow all warnings and instructions marked on the television . 1 . Read , Retain and FollowAll Instructions Read all safety and operating instructions before operating the TV . Retain the safety and operating instructions for future reference . Follow all operating and use instructions . 2 . Heed Warnings Adhere to all warnings on the appliance and in the operating instructions . 3 . Cleaning Unplug the TV from the wall outlet before cleaning . Do not use liquid , abrasive , or aerosol cleaners . Cleaners can permanently damage the cabinet and screen . Use a lightly dampened cloth for cleaning . 4 . Attachments and Equipment Never add any attachments and / or equipment without approval of the manufacturer as such additions may result in the risk of fire , electric shock o1 " other personal injury . 5 . Water and Moisture Do not use the TV where contact with or immersion in water is possible . Do not use near bath tubs , wash bowls , kitchen sinks , laundry tubs , swimming pools , etc . 6 . Accessories Do not place the TV on an unstable cart , stand , tripod , or table . The TV may fall , causing serious injury : o a child or adult and serious damage m the TV . Use only with a cart , stand , tripod , bracket , or table : ecommended by the manufacturer , or sold with the TV . Any mounting of the TV should follow the manufacturer's instructions , and should use mounting accessories recommended by the manufacturer . _ _ nappliance and cart combination should be moved with care . O . uick stops , excessive force , and uneven mrfaces may cause the appliance and cart combination m overturn . Z Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the TV and to protect it from overhearing . Do not block these openings or allow them to be obstructed by placing the TV on a bed , sofa , rug , or other similar surface . Nor should it be placed over a radiator or heat register . If the TV is to be placed in a rack or bookcase , ensure that there is adequate ventilation and that the manufacturer's instructions have been adhered to . 8 . Power Source This TV should be operated only from the type of power source indicated on the marking label . If you are not sure of the type of power supplied to your home , consult your appliance dealer or local power company . 9 . Grounding or Polarization This TV is equipped with a polarized alternating cm'rent line plug having one blade wider than the other . This plug will fit into the power outlet only one way . If you are unable to insert the plug fully into the outlet , try reversing the plug . If the plug should still fail to fit , contact your electrician to replace your obsolete outlet . Do not defeat the safety pro'pose of the polarized plug . 10 . Power - Cord Protection Power - supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them , paying particular attention to cords at plugs , convenience receptacles , and the point where they exit from the TV . 11 . Lightning For added protection for this TV during a lightning storm , or when it is left unattended and unused for long periods of time , unplug it from the wall outlet and disconnect the antenna or cable system . This will prevent damage to the TV due to lightning and powerqine surges .
Page: 4
IMPORTANT SAFEGUARDS , continued 12 . Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits , or where it can fall into such power lines or circuits . When installing an outside antenna system , extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal . 13 . Overloading Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock . 14 . Object and Liquid Entry Never push objects of any kind into this TV through openings as they may touch dangerous voltage points or short - out parts that could result in fire or electric shock . Never spill liquid of any kind on or into the TV . 15 . Outdoor Antenna Grounding If an outside antenna or cable system is connected to the TV , be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built - up static charges . EXAMPLE OF ANTENNA GROUNDING Section 810 of the National Electric Code , ANSI / NFPA No . 70 - 1984 , provides LEAD _ N WIRE information with respect to proper grounding of the mast and supporting structure , grounding of the lead in wire to an antenna discharge unit , size of grounding GRQUND CLAMp ANTENNA DISCHARGE UNIT conductors , location of antenna discharge unit , connection m grounding electrodes , { NEC SECT _ QN 810 20 ) and requirements for the grounding electrode . GROUNDING _ i NT _ CNNATORS CONDU { NEC S ECT _ Q N 910 21 ) 16 . Servicing lIND CLAMPS Do not attempt to service this TV yourself as opening or removing covers may expose _ pOWER S Ef _ VLCE GROUNDING ELECTRODE SYSTEM you to dangerous voltage or other hazards . Refer all servicing m qualified service NEC NATIONAL ELECTRICAL CODE ( NUC ART 250 , PART H ) personnel . 1Z Damage Requiring Service Unplug the TV from the wall outlet and refer servicing to qualified service personnel under the following conditions : ( a ) When the power - supply cord or plug is damaged . ( b ) If liquid has been spilled , or objects have fallen into the TV . ( c ) If the TV has been exposed to rain or water . ( d ) If the TV does not operate normally by following the operating instructions , adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the TV to its normal operation . ( e ) If the TV has been dropped or the cabinet has been damaged . ( f ) When the TV exhibits a distinct change in performance - this indicates a need for service . 18 . Replacement Parts When replacement parts are required , be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part . Unauthorized substitutions may result in fire , electric shock or other hazards . 19 . Safety Check Upon completion of any service or repair to the TV , ask the service technician to perform safety checks to determine that the TV is in safe operating condition . 20 . Heat The product should be situated away from heat sources such as radiators , heat registers , stoves , or other products ( including amplifiers ) that produce heat .
Page: 5
IMPORTANT NOTES Warning : Do not leave stationary PIP / POP , or letterbox images on the screen for extended periods of time . Mix the types of pictures shown . Uneven picture tube aging is NOT covered by your warranty . The normal use of a TV should include a Examples of these types of images can be , but mixture of TV picture types . The most are not limited to the following : frequently used picture types should fill the screen with constantly moving images Letterbox top / bottom black bars : rather than stationary images or patterns . shown at the top and bottom of the TV screen Displaying the same stationary patterns over when you watch a widescreen ( 16 : 9 ) movie on extended periods of time or displaying the a standard ( 4 : 3 ) TV . same stationary pattern frequently can leave subtle but permanent ghost images . To avoid Side bar images : this , mix your viewing patterns and reduce the solid bars shown on each side of an image initial contrast level . Do not show the same when watching a standard ( 4 : 3 ) program on a stationary image for more than 15 % of your total TV viewing in any given week . Display widescreen ( 16 : 9 ) TV . constantly moving and changing images that fill the screen whenever possible . _ . News and stock - market report bars : ticker running at the bottom of the TV screen . This projection TV uses picture tubes to project the image to the screen . All picture tubes age with Shopping channel logos & pricing displays : use . As they age , their light output is gradually bright graphics that are shown constantly or reduced . Normal TV pictures fill the screen repeatedly in the same location . with constantly changing images . Under these conditions , picture tubes age at an even rate across the entire screen . This maintains Video game patterns and scoreboards a TV picture that is evenly bright over the whole screen . Stationary images or images Bright station logos : that only partially fill the screen ( leaving black moving or low - contrast graphics are less likely or colored bars to fill the screen ) , when used to cause uneven aging of the picture tubes . over extended periods of time or when viewed repeatedly , can cause uneven aging of the Online ( Internet ) websites : phosphors and leave subtle ghosts from the or any other stationary or repetitive computer stationary images in the picture . style images , including digital photos . Still or stationary images may be received from Closed Captioning broadcasters , cable channels , satellite channels , Mitsubishi recommends using a gray DVD discs , video tapes , laser discs , on - line background rather than black or a bright color services , web / Internet searching devices , video if you frequently use closed captioning . games , and digital TV tuner / converter boxes .
Page: 6
1 Front Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Back Panel Input / Output for WS - 48413 , WS - 55413 , WS - 65413 . . . . . . . . . . . . . . . . . . . . 12 Side Panel Input / Output for WT - 42413 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Page: 7
Thank You for Your Purchase Welcome to the wonderful and exciting world of digital television ! We are honored that you chose Mitsubishi as your premier home entertainment partner . The development team at Mitsubishi Digital Electronics America ( MDEA ) understands that our customers demand and expect the very best . MDEA was founded on the core beliefs and philosophies that drive us to deliver products that implement the latest in advanced television technology . While some televisions are destined for obsolescence in the near future , MDEA's televisions are all HD - upgradeable . This cornerstone of your home entertainment system will continue to provide unparalleled enjoyment for years to come ! Whether this is your first Mitsubishi consumer electronics product or another addition to your growing Mitsubishi system , we hope that this television will bring you many hours of enjoyment . OUR PROMISE We will engineer and manufacture the upgrades necessary so the HD - upgradeable television you purchased today can be made compatible with near - future advances in digital television and digital interconnectivity . Specifically , we promise that you will be able to have your television upgraded , at a reasonable cost , to include an off - air HDTV tuner , a cable TV tuner ( for unscrambled programming ) , an IEEE 1394 ( FireWire ® ) connection , HAVi system control , and 5C copy protection .
Page: 8
Unpacking Your New TV Special Features Please take a moment to review the following list of Your new High Definition ( HD ) upgradeable items to ensure that you have received everything bigscreen television has many special features that make including : it the perfect addition to your home entertainment system . A few of these special features are : PIP / POP Viewing Option Using Picture - in - Picture and Picture - outside - Picture gives you exciting options for viewing favorite programs . Seepages 22 , 29 and 63for more information . Remote Control HD Upgradeable With the use of an optional HDTV receiver ( Mitsubishi HD - 5000 or similar model ) your Mitsubishi bigscreen can display high definition pictures . Seepage 20for connection information . Mukibrand Remote Control 2 AA Batteries Your Mitsubishi remote control can be programmed to control many other audio / video components . Seepages 27 - 29 for more information . NetCommand ® IR ( WS - 48413 , W8 - 55413 , WS - 65413 ) When you connect your compatible audio or video devices to the television , the television can " learn " which audio and / or video devices are connected . The TV remote control will then be able to control 2 Double IR Em # ter Cables these devices . ( WS - 48413 , WS - 55413 , WS - 65413 ) Seepages 36 - 38 for more information V - Chip Technology Mitsubishi understands you may want to shield certain viewers from specific program content . Your Mitsubishi bigscreen will allow you to restrict programming by general contents , specific contents , or even by time . Seepages 48 - 52 for more information . 16 : 9 Widescreen TV Enjoy a full theatrical experience in the comfort of Product Registration Card your home . View pictures as film directors intended them . Both the DTV and DVD support the widescreen format well - suited for your new TV . Seepages 62 - 63for more information . Quick Reference Card ( notpictured )
Page: 9
NetCommand ® IR for models WS - 48413 , WS - 55413 , WS - 65413 Your new Mitsubishi television is equipped with NetCommand IR , the latest breakthrough in home theater control . NetCommand technology makes your television the brain of your home theater . By connecting compatible A / V devices and then using the menu to have the television " learn " which devices are connected , you will be able to view and control these devices . This will allow you to : • Use one menu , the Device Selection Menu to select devices to use , either individually or in combination . • Operate all compatible devices from a single remote control . • Enjoy automatic switching of both video source for the TV and audio source for your A / V Receiver . • Easily switch from TV speakers to Audio Receiver speakers . • Update new devices that are added to your home theater system .
Page: 10
Front Control Panel Many remote control buttons are duplicated on the front control panel . Duplicate buttons are shaded in the panels shown below . Please see Remote Control Functions , page 24 , for an explanation of their usage . F F The ADJUST , ENTER , MENU , and CANCEL buttons may be used to accessor navigate through the screen menus Timer F During normal operation , the timer light glows green D when the TV is on . It does not glow when the TV is off . When the timer is used to turn the TV on at a TIMER specific time , the green timer light blinks while the TV is off . See Timer Menu , page 54 for timer setup instructions . A / V Reset Press this button to reset all A / V memory inputs to AN RESET the factory default settings . See Audio / Video Settings Menu , page 58 for instructions . CANCEL Format FORMAT Press this button to change the size and shape of the main TV picture . ENTER Input - 3 S VIDEO VkDEO L - AUDtO - R This input can be used for convenient connection of a camcorder or other video device to the TV . You may ® ° connect to the S - VIDEO or VIDEO terminal but not to both .
Page: 11
Back Panel Input / Output for WS - 48413 , WS - 55413 & WS - 65413 Side Panel Input / Output for WT - 42413 WT - 42413 Side Panel WS - 48413 , WS - 55413 , WS - 65413 Back Panel 2 3 4 5 - 7 L , J 1 . ANT - A , LOOP OUT and ANT - B ( Antenna ) 6 . MonitorLinkWDVI ANT - A and ANT - B receive signals from VHF / UHF antennas This is a Mitsubishi - exclusive proprietary digital interface for or a cable system . LOOP OUT sends the ANT - A signal out to the display of high quality digital video signals from Mitsubishi another device , such as a cable box or VCR . products such as the HD - 5000 HDTV Receiver / Controller . Note : LOOP OUT is disabled when Energy Mode is set to All video signals , both analog and digital can be sent digitally Low . to your Mitsubushi TV from the HD - 5000 . This can also be used as a DVI input for other compatible sources . Note : The DVI - HDTV input terminal is compliant with the 2 . Monitor Out EIA - 861 standard and is not intended for use with personal The Monitor Output sends the TV audio and video signals computers . ( excluding component video , DTV video and MonitorLink ) to an A / V receiver or other equipment . MonitorLink TM Control / RS - 232C 7 . A digital control interface that works in parallel with 3 . Inputs 1 - 2 MonitorLink . While MonitorLink provides the digital video These inputs can be used for the connection ofa VCR , Super signal , MonitorLink Control provides enhanced functioning VHS ( S - VHS ) VCR , laser disc player , or other A / V device to such as automatic power ON / OFF and input selection . This the TV . With each input , you may connect to the S - VIDEO can also be used with other compatible RS - 232C external or VIDEO terminal but not to both . control devices . Please visit www . mitsubishi - tv . com for more information on RS - 232C command structure . - 4 . Component Inputs 1 - 2 ( Component only for WT - 42413 ) 8 . IR Emitter Repeater These inputs can be used for the connection of A / V equipment Connecting IR emitters here allows the TV to pass IR with component video outputs , such as a DVD player or Video commands from most IR remote controls to other A / V devices Game System . Please see Appendix B , page 67 , for signal that are out of range of the remote control . Note : This feature compatibility . is not available on the WT - 42413 . 5 . DTV Input , Net Command * IR Input This input is used to connect a DTV receiver or cable box IR emitters connected to these jacks are used by NetCommand and can be configured for HDTV component ( YPbPr ) , or system of the TV to control external analog devices such RGB plus H & V . Please see Appendix B , page 67 , for signal as VCRs , DVDs , cable boxes , satellite receivers and audio compatibility . receivers . Note : This feature is not available on the WT - 42413 .
Page: 12
2 Connecting a DVD Player or Other S - Video Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Connecting a DTV Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Connecting MonitorLink TM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Connecting NetCommand _ IR Emitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 How Connections Affect the PIP and POP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Page: 13
Connecting an Antenna or Wall Outlet Cable VHF _ tenna O _ F _ a _ t _ r _ a - { Ohat _ ne _ 2s 13 } ( Ghatv _ s _ 4 69 Separate UHF and VHF Antennas ( Figure 1 ) Flat T _ Log F _ atTwin Lead £ × t _ at 1 . Connect the UHF and VHF antenna leads to the or Oab _ e UHF / VHF combiner . * IV back panel ( section detail ) 2 . Push the combiner onto ANT - A on the TV back panel . UHF / VHF combiners are not provided with _ * 8aek 8 _ the TV . They are available at most electronic stores . [ ] Figure l . Connecting separate UHF and VHF antennas . NOTE : This TV will only be able to provide an analog signal through ANToA on the TV back Note : Seepage 5for Outdoor Antenna Grounding panel . Twin Lead Antenna , Coaxial Lead Antenna , or Wall Outlet Cable ( Figure 2 ) For antenna with twin flat leads : TV back panel { section detail ) 1 . Connect the 300ohm twin leads to the transformer . 2 . Push the 75ohm side of the transformer onto ANToA on the TV back panel . Optional 3OOOhm to ZS 0 _ Matchang _ ransfo _ 300ohm to 75ohm matching transformers are not provided Figure2 . Connecting twin lead antenna , coaxial lead with the TV . They are available at most electronie stores . antenna , or wall outlet cable . For cable or antenna with coaxial lead : Note : Seepage 5for OutdoorAntenna Grounding 3 . Connect the incoming cable to ANT - A on the TV back panel . NOTE : This TV will only be able to provide an analog signal through ANToA on the TV back panel .
Page: 14
Connecting an Antenna to a Cable Box or VCR " IV back panel ( section detail ) Cable Box ( Figure 3 ) Incoming Cable 1 . Connect the incoming cable to ANT - A on the TV back panel . Connect two coaxial cables as follows : 2 . One from LOOP - OUT on the TV back panel to IN [ ] on the cable box back panel . 3 . One from OUT on the cable box back panel to ANT - B on the TV back panel . c eBox NOTE : If your cable box has separate audio ! video o k panelsectioi I outputs , please see Composite Video with Figure 3 . Connecting the cab # box that does not have Audio or S - Video with Audio , page 16 audio or video outputs . ( Figure 6 ) . Note : Seepage 5for Outdoor Antenna Grounding TV back panel ( section detail ) Antenna or Wall Outlet Cable ( Figure 4 ) 1 . Connect the incoming cable to ANT - A on the TV back panel . Connect two coaxial cables as follows : 2 . One from LOOP - OUT on the TV back panel to ANTENNA IN on the VCR back panel . VCR back panel 3 . One from VCR back panel ANTENNA OUT to ANT - B on the TV back panel . m , t I NOTE : If your cable box has separate audio ! video Figure 4 . Connecting the VCR with antennas or wall outputs , please see Composite Video with outlet table . Audio or S - Video with Audio , page 16 ( Figure 6 ) .
Page: 15
Connecting an Antenna to a Cable Box and VCR , Connecting Audio / Video to the Cable Box or VCR _ ck _ n # l _ n # _ ti _ hown h _ are fo _ _ # fe _ _ ld _ _ d va @ b _ TV back panel ( section detail ) Cable Box Incoming Cable ( Figure 5 ) 1 . Connect the incoming cable to ANT - A on the TV [ ] [ ] back panel . Connect three coaxial cables as follows : 2 . One from LOOP - OUT on the TV back panel to IN on the back of the cable box . 3 . One from OUT on the back of the cable box to ANTENNA IN on the VCR back panel . 4 . One from ANTENNA OUT on the VCR back panel to ANT - B on the TV back panel . Figure 5 . Connecting the VCR with cable box . NOTE : For best performance , please see Composite Video with Audio or S - Video with Audio , below . Composite Video with Audio or S - Video with Audio ( Recommended ) ( Figure 6 ) TV back panel ( section detail ) . Connect a video or S - Video cable from VIDEO OUT on the VCR back panel to VIDEO or S - VIDEO , INPUT - 1 or INPUT - 2 on the TV back panel . 2 . Connect a set of audio cables from AUDIO OUT on the VCR back panel to AUDIO INPUT - 1 or INPUT - 2 on the TV back panel . • The red cable connects to the R ( right ) channel • The white cable connects to the L ( left ) channel If your VCR is mono ( non - stereo ) , connect only the white ( left ) cable . Figure 6 . Connecting the VCR Audio / Video . ou may connect to the S - VIDEO or VIDEO rminal but not to both .
Page: 16
Connecting an Audio Receiver " rv back panel Stereo Audio System ( recommended for shelf units or A / V receivers without digital audio inputs ) ( Figure 7 ) Connect the audio cables from AUDIO . MONITOR OUTPUT on the TV back panel to TV IN or AUX IN terminals on the back of the audio system . [ ] • The red cable connects to the R ( right ) channel • The white cable connects to the L ( left ) channel 2 . Turn offthe TV's speakers through the AUDIO / VIDEO SETTINGS Menu , page 58 . 3 . Set the audio system's input to the TV or AUX position to hear the TV's audio through your Figure Z Connecting the StereoAudio System . stereo system . A / V Receiver ( Figure 8 ) . Connect either a video cable or an S - Video cable ( but not both ) from VIDEO MONITOR OUT on the back of the A ! V receiver to VIDEO INPUT - 1 or INPUT - 2 on the TV back panel . 2 . Connect a video cable from VIDEO MONITOR OUTPUT on the TV back panel to VIDEO TV IN on the back of the A / V receiver . 3 . Connect a set of audio cables from AUDIO MONITOR OUTPUT on the TV back panel to AUDIO TV IN on the back of the A / V receiver . • The red cable connects to the R ( right ) channel Figure 8 . Connecting the A / V Receiver . • The white cable connects to the L ( left ) channel
Page: 17
Connecting a DVD Player or Other S - Video Device DVD Player with Component Video ( Figure 9 ) . Connect the Component Video cables from ( YCbCr or YPbPr ) VIDEO OUT on the back of the DVD player to COMPONENT ( 1 or 2 ) on the TV back panel . The correct connections are : A . YtoY E B . Cb or Pb to Pb C . Cr or Pr to Pr Figure 9 . Connecting a DVD Player with Component 2 . Connect a set of audio cables from AUDIO OUT Video . on the back of the DVD player to COMPONENT AUDIO Input ( 1 or 2 ) on the TV back panel . • The red cable connects to the R ( right ) channel IMPORTANT • The white cable connects to the L ( left ) channel NOTE : Some video game systems support component connections . Please refer to your video game console Owner's Guide . NOTE : If your DVD player supports progressive scan playback , be sure to set your player TV back panel ( section detail ) accordingly . Please refer to your DVD player's Owner's Guide . Other S - Video Device ( Figure 10 ) 1 . Connect an S - Video cable from VIDEO OUT on the device back panel to VIDEO INPUT - 1 or INPUT - 2 on the TV back panel . 2 . Connect a set of audio cables from AUDIO OUT [ ] on the device back panel to AUDIO INPUT - 1 or INPUT - 2 on the TV back panel . • The red cable connects to the R ( right ) channel • The white cable connects to the L ( left ) channel Figure 10 . Connecting an S - Video Device . If your S - Video Device is mono ( non - stereo ) , connect only the white ( left ) cable .
Page: 18
Connecting a DTV Receiver DTV Connectors and Adaptors ( Figure 11 ) The TV back panel has five RCA - type connectors for the DTV connection . The back panel of your DTV receiver may use RCA - type connectors or BNC - type or connectors . If your DTV receiver comes with BNC BNC to A or RCA type connections , you will need to purchase BNC to RCA BNC Fitted to Connector RCA adaptors to connect the TV to the DTV receiver . Adaptor Connector Connection These adaptors should be available at most electronic Figure ll . DTVconnectors and adaptors . supplystores . DTV Receiver with Component Video Connections ( Recommended ) ( Figure 12 ) Connect the outside antenna cable , or satellite to . ANT or SATELLITE IN on the DTV receiver ( see your DTV receiver owner's guide for instructions and cable compatibility ) . . If your DTV receiver has a built - in terrestrial tuner connect the incoming terrestrial antenna to ANT on the DTV receiver . If your DTV receiver does not have a built - in terrestrial tuner , this TV will only be able to provide an analog signal through Ant - A on the TV back panel . 3 . Connect the RCA - type cables from the DTV receiver outputs to DTV INPUT Y ! Pb / Pr on the TV back panel . You may need to set the DTV Input Assignment to Y ! Pb ! Pr . ( see page 35 for WT - 42413 or page 38 for WS - 48413 , WS - 55413 or WS - 65413 ) 4 . Connect the L ( left ) and R ( right ) audio cables from the DTV receiver to DTVAUDIO on the TV ba & panel . 5 . To utilize the benefits of a digital A ! V receiver , connect your DTV receiver's digital audio out to a digital input on your digital A / V receiver . Component ( 1 and 2 ) may also be used for 1080i components . Figurel2 . ConnectingtheDTVreceiverwith component Video Connections .
Page: 19
DTV Receiver with RGB Video Connections ( Figure 13 ) . Connect the outside antenna , cable , or satellite to ANT or SATELLITE IN on the DTV receiver ( see your DTV receiver owner's guide for instructions and cable compatibility ) . . If your DTV receiver has a built - in terrestrial tuner , connect the incoming terrestrial antenna to ANT on the DTV receiver . If your DTV receiver does not have a built - in terrestrial tuner , this TV will only be able to provide an analog signal through Ant - A on the TV back panel . . Connect the RGB cables from the DTV receiver to the TV back panel as listed below ( if your DTV receiver uses BNC - type cables , use the adaptors shown in Figure 11 , page 19 ) : DTV Receiver TV Back Panel G ( green ) Y / G B ( blue ) Pb / B R ( red ) Pr / R . If the DTV receiver has outputs for H and V sync , connect as listed below ( DO NOT connect if DTV receiver uses " Sync on Green " ) : H ( horizontal sync ) H V ( vertical sync ) V . Connect the L ( left ) and R ( right ) audio cables from the DTV receiver to DTV AUDIO on the TV back panel . . To utilize the benefits of a digital A ! V receiver , connect your DTV receiver's digital audio out to a digital input on your digital A / V receiver . You may need to setup the DTV ( See Input Assignment , page 35 for WT - 42413 or page 38 for WS - 48413 , WS - 55413 , WS - 65413 ) to RGB .
Page: 20
MonitorLink / DVI ( Figure 14 ) 1 . Connect a MonitorLink / DVI cable from the TV back panel to the Mitsubishi HD Receiver / Controller back panel . 2 . Connect the MonitorLink Control / RS - 232 cable from the TV back panel to the Mitsubishi HD Receiver / Controller back panel . . Connect the L ( left ) and R flight ) audio cables from the HDTV receiver to AUDIO LEFT and AUDIO RIGHT on the MonitorLink section of the TV back panel . NOTE : The 29 pin MonitorLink ! DVI and RS - 232 cables can be found at your local electronics store . Figurel4 . ConnectingMonitorLink CAUTION : To assure continued FCC compliance , IR Emitter Repeater and the user must use a shielded video interface cable with NetCommand ® IR bonded ferrite cores at both ends , when using the ( Figure 15 ) ( WS - 48413 , WS - 55413 , WS - 65413 ) MonitorLink / DVI input . The two IR jacks labeled REPEATER are not used by NetCommand , but will repeat any IR command received by the TV . The NetCommand * IR jacks are used by NetCommand to control external devices . They both . . . . t9 . . . . connect the same way : 1 . Connect one of the IR emitters to one IR EMITTER jacks on the TV back panel . OtherA / VDevice I . Place the IR emitter cable under or on top of each A ! V device . Place the IR lens directly in front of the A ! V device infrared signal receiver , usually located behind the front translucent panel of the receiver . Figure 15 . Connecting IR Emitters W8 - 48413 , W8 - 55413 , W8 - 65413 3 . If you are connecting to only one A ! V device , place the unused transmitter in an out - of - the - way location . . For permanent installation of the IR emtter cable , use the included double sided adhesive tape to secure the body of the emitter to the A / V receiver , DVD player , Cable box , etc . . .
Page: 21
How Connections Affect the PIP ( Picture - in - Picture ) and POP ( Picture - Outside - Picture ) To see a picture in the PIP or POP , you may need to select an input source . If the only input connected is ANT - A , then both the main picture and the PIP / POP will be from that input source . If other video equipment is connected , you may be able to view these input sources as the PIP / POP . When connecting your new Mitsubishi TV , it is important to understand which main picture and PIP / POP input sources can and cannot be used together . The table on this page shows which inputs can and cannot be used together and the limitations they may have . If you press the INFO button it will display the current Input , signal ( 480i , 480p , or 1080i ) , format , time , day and sleep time . See Operation of PIP and POP , page 62 , for operating instructions . i _ ! _ i ! ii _ 6 _ _ ! i2iiii ! i ! iil ! i ¸ ii ! i ! ! i OK * No PIP / POP OK OK OK OK OK * OK OK OK OK OK OK * * OK OK OK OK OK OK * * OK OK OK OK OK OK * * OK OK OK OK OK * No Side - by - Side with the same channel * * No Side - by - Side with the same input t Component 2 is not available on the WT - 42413
Page: 22
3 Operation of PIP and POP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Page: 23
Remote Control Functions : Overview of the TV Layer Buttons INFO : Displayon - screen summary of the current Overview input used and any broadcast information available ( Figure 1 , following page , ) ( including current V - Chip information , Signal Source Slide Switch : Select A / V product to be controlled by and Format ) . Additionally , if you press the INFO key , the remote control . it will display time , day and sleep time . POWER : Turns power on and off for TV and other AUDIO : Select the individual audio settings . connected A / V products . VIDEO : Select the individual video settings . Numbers : Individually select channels or input information into TV . PIP CH : Scroll up or down through memorized channels in PIP or POE SQV ( Super Quick ViewTM ) : Scan through a memorized list of favorite channels . PIP / POP : Cycle through PIP and POP display choices . Qy ( OAfick ViewTM ) : Switch to last channel viewed . EXCH : Exchange PIP or POP with the main TV GUIDE : When the slide switch is set to CABLE / picture . DBS / DTV , display the on - screen program guide SLEEP : Set the TV to turn offwithin 2 hours . See ( some cable boxes and DBS / DTV receivers ) . Sleep Timer , page 26 , for setup instructions . DEVICE : Select the input to view ; Ant - A , PIP DEVICE : Select the PIP or POP input source . Ant - B , DTV , Component - i , Component - 2 , Input - l , Input - 2 , Input - 3 , MonLink , Device Selection Menu . FORMAT : Change the shape and size of the main ( Component 2 and Device Selection Menu not available TV picture . on WT - 42413 . ) CONNECT : No current function . CH ( channel ) : Scroll up or down through memorized REC : Manually record with your VCR or recordable channels . Skips DVD chapters in DVD layer . DVD . VOL ( volume ) : Change sound level . REW / REV : Rewind or reverse search with your MUTE : Turn sound on or off . VCR , reverse scan with your DVD , or skip reverse with your CD . TV MENU : Display ] _ E ® on - screen menu system . PLAY : Play your VCR , DVD , or CD . DEVICE MENU : Display menu for a connected STOP : Stop your VCR , DVD , or CD . A / V device . ( Not available on WT - 42413 ) FF / FWD : Fast forward or forward search with ADJUST . ' Navigate menus , change settings , and move your VCR , fast play with your DVD , or skip for - the PIP on - screen location . ward with your CD . ENT ( enter ) : Select a channel number or menu item . PAUSE : Pause your VCR , DVD , AV Disc , or freeze HOME : Exit on - screen menus and return to TV the PIP or POP image . viewing . CANCEL : Clear SQV and some menu entries . Used NOTE : For WS - 48413 , WS - 55413 , WS - 65413 , to as a subchannel button in Cable / DBS / DTV layer . program the remote control for NetCommand ® , hold V - CHIP : Displays V - Chip Passcode screen , use to the Power button while entering the code 935 . enable or disable the V - Chip Lock .
Page: 24
Remote Control Functions : Care and Operation Operation Installing the Batteries : ( Figure 2 ) 1 . Remove the remote control's back cover by gently pressing the ridged tab in the direction of the arrow and sliding off the cover . 2 . Load the batteries , making sure the polarities ( + ) and ( - ) are correct . For ease of installation , install the negative ( - ) side first . For Best Results from the Remote Control : _ . Be within 20 feet of the equipment . _ . Do not press two or more buttons at the same time unless instructed to . _ . Do not allow to get wet or become heated . _ . Avoid dropping on hard surfaces . , _ MITSiJEHSHI _ . Do not use harsh chemicals to dean . Use only a soft , lightly moistened cloth . Figure l . Remote ControlFunctions . Do not mix new and old batteries . Do not heat , take apart , or throw batteries into fire . Use only AA batteries . batteries Operating the Remote Control : You can use the remote to control the TV , CABLE / DBS / DTV , VCR , DVD , and AUDIO products . Select the product you want to control by moving the Figure 2 . Installing the batteries . slide switch to the appropriate position . The remote control has been preset to operate the TV and other Mitsubishi products . To program the remote control to operate other products , see Use of the Remote Control with Other A / V Products , page 27 .
Page: 25
Remote Control Functions : Channel Selection , Sleep Timer Channel Selection Enter three numbers ( ex . for channel 2 , press 002 ) . or Press the channel number and ENT ( ex . for channel 2 , press 2 , then ENT ) . or Enter the channel number and wait four seconds ( without pressing ENT ) . The TV will change automatically . Sleep Timer ( Figures 3 & 4 ) PIP CH PIP / POP EXCH SLEEP Setting the Sleep Timer : Press SLEEP on the remote control . PiP DEVICE FORMAT CONNECT ( 2 ) A message indicating the length of time the sleep timer is to be set appears on the TV screen . Each press of SLEEP will increase the time Figure 3 . Sleep button on remote control displayed by 30 minutes , until the maximum value of 120 minutes is reached . After 5 seconds of inactivity , the message will disappear . Sleep : 30 min . Press SLEEP to view the remaining time before the timer turns the TV off . Canceling the Sleep Timer : Press the SLEEP button to display the on - screen message . Figure 4 . On - screen display for sleep timer Press SLEEP repeatedly until OFF is displayed . After 5 seconds of inactivity , the message will disappear .
Page: 26
Use of the Remote Control with Other A / V Products CABLE / DBS / DTV _ VCR DVD _ TV - e J , $ _ - AUDIO . I II I I . Programming the Remote Control 1 , c , ( [ o ] ) ) to Use with Other Brands of Audio 1 [ , _ . . . _ 1 _ and Video Products : Cable box brand Codetoen _ r : If your cable box General Instruments / 119 , 120 , 121,122,123 , ( Figures 1 - 3 this page , figures 4 - 5 following page ) code is not Jerrold 124 listed here , Motorola 125,126,127 please see l . Move the slide switch at the top of the remote to Oak 139,137,102 page 68 Pioneer 101,116 the product you want to control . for a Scientific Atlanta 112,113 complete 2 . Press and hold the POWER button on the remote Zenith 117,100 listing . control . To reset to default code , enter 000 3 . Enter the first three digit code listed for your Figure 1 . Programming the remoteto controlyour cablebox . equipment , and then release the POWER button on the remote control . 4 . Point the remote control to the equipment and press the POWER button . Note : If the equipment responds , the remote control is CABLE / DBS / DTM VCR DVDo - properly programmed to operate the equipment . If TV _ " 1 _ , [ AUDIO I tll I the equipment does not respond , repeat steps 2 - 4 1 . ( ( ill ] ) ) with the next three digit code listed in step 3 for your equipment . . } " I _ IIl [ : l : I : I _ : _ t , l _ APr . ' , i . 11 Satellite brand Codeto enter : If your Mitsubishi DTV - DBS 006 satellite DishNetwork 175 receiver Hughes - DBS 173 code is not Panasonic - DBS 174 listed here , RCA - DBS 176 please see Sony - DBS 177 page 69 for a Toshiba - DBS 179 , 173 , 189 , 190 , 191 complete To reset to default code , enter 000 listing . Figure2 . Programming the remote to control your satellite receive _ CABLE / DBS / DTV _ VCR DVD TV - e J , { , _ _ - AUDIO I II I I 1 . ( ( m ) ) 3.1 VCR brand Oodetoenten If your VCR Mitsubishi 0Old002 code is not Hitachi 020,043,065 listed here , JVC 030,054 please see 043,044,051 Phillips / Magnavox page 69 Panasonic 041,042,043 fora RCA 020,053,065 complete Sony 048,049,050 listing . Toshiba 021 To reset to default code , enter 000 Figure 3 . Programming the remote to control your VCR .
Page: 27
Use of the Remote Control with Other A / V Products F _ WS _ 8 _ 3 WS _ 5 _ ! 3 _ WS 65 _ th _ fo ! ! owi _ g ! _ fo _ _ _ aPP ! _ ! # ffyo _ _ _ CABLE / DBS / DTV _ VCR DVD After entering the correct codes in each position of the TV - = J , _ _ . - AUDIO I II I I remote control , use the dide switch to select which 1 . ( ( [ , } ) product will respond when an operational button is pressed . If you enter a code from the AUDIO chart i DVD / LDP brand Codeto enter ' . If your while the slide switch is set to TV , the volume and DVD Mitsubishi 003 mute functions change to match the A / V receiver . code is not JVC 257 listed here , Panasonic 250 This is useful when using an A / V receiver with the please see Philips 258,253 , 272 page 68 TV all the time . In all other cases , only one of the 252 Pioneer DVD fora 261 Samsung below devices is allowed for each slide switch position . complete 254 Sony listing . Toshiba 253 ro reset to default code , enter 000 TV position : Figure 4 . Programming the remote to contro / your [ ] TV DVD or LDP . [ ] AIV receiver ( volume and mute only ) Cable / DBS / DTV position : CABLE / DBS / DT _ L VCR DVD [ ] Cable box TV - Q _ _ _ e - AUDIO [ ] Satellite receiver ( [ II ] ) 2 , 1 . ( ' " ' ' [ ] DTV receiver 11 VCR position : Audio brand Codetoenten [ ] VCR tt your Mitsubishi A / V receiver 010 , 015,011,012 , audio and / or CD player 013 . 014 code is not DVD position : 234,235,236,245 , listed here , Denon 246,359 [ ] DVD please see Harman Kardon 215 _ 223,242 page 68 JVC [ ] LD Player fora 233.232 Kenwood complete 208,200 Marantz listing . 224,350 Audio position : Onkyo 209 _ 214,240 , 247 [ ] A ! V receiver Pioneer 205 _ 207 Sony 222,249 [ ] Mitsubishi CD player Technics 218 _ 219 , 221 Yamaha 202.201.243.244 If you have a Mitsubishi A / V receiver , the audio position To reset to default code , enter 000 may be used in conjunction with select Mitsubishi CD Figure 5 . Programming the remote to control yourA / V players ' . Your audio position must beprogrammed to recei _ ' e _ either 010 or 011 . Plug the CD player power cord into a switched outlet on the back ofyour A / V receiver . Pressing the POWER button turns On the A / V receiver , along with the CDplayer . In the audio position , for some CD players , the transport controls ( FF , Play , Rew , etc . ) operate the CD player . IMPORTANT
Page: 28
Remote Control Functions : Special Functions When your remote control has been Programmed to operate another manufacturer's product , the function performed on each layer may vary . The most common functions are : oMitsubishi VCRs will be com with additional buttons oPOWER • ENTER ( on some models ) oADJUST up / down / left / right ( on some models ) oCHANNEL up / down • CANCEL ( on some models ) • 0 - 9 Number Buttons ( on some models ) • GUIDE ( on some models ) oPOWER * VOLUME • MUTE oDirect Input Selection Buttons - use number buttons , SQV , and QV ( on some models ) ( on some • 0 - 9 Number Buttons 3n some Remote Control Functions : Operation of PIP and POP Activating the PIP and POP Picture - In - Picture ( PIP ) and Picture - Outside - Picture ( POP ) features allow you to view Programming in different ways . While watching Press PIWPOP to choose a display format . Each the main screen , you can display programs from time the PIWPOP button is pressed on the TV other channels and other inputs . To see which remote control ( within 3 seconds of each other ) , inputs can and cannot be used together , see How the PIP / POP cycles through the following display Connections Affect the PIP and POP on page 22 . options . You can display large and small PIPs , side - by - side 1 . POP : side - by - side pictures pictures , three POPs , or nine POPs . 2 . POP : three POPs 3 . POP : nine POPs 4 . PIP : large PIP 5 . PIP : small PIP To turn PIWPOP Off , wait at least 10 seconds , and press PIWPOR The next time you activate PIWPOP , the last used PIWPOP format will be displayed first .
Page: 29
IMPORTANT NOTES Warning : Do not leave stationary PIP / POP , or letterbox images on the screen for extended periods of time . Mix the types of pictures shown . Uneven picture tube aging is NOT covered by your warranty . The normal use of a TV should include a Examples of these types of images can be , but are mixture of TV picture types . The most not limited to the following : frequently used picture types should fill the screen with constantly moving images Letterbox top / bottom black bars : rather than stationary images or patterns . shown at the top and bottom of the TV screen Displaying the same stationary patterns over when you watch a widescreen ( 16 : 9 ) movie on extended periods of time or displaying the a standard ( 4 : 3 ) TV . same stationary pattern frequently can leave subtle but permanent ghost images . To avoid Side bar images : this , mix your viewing pattern and reduce the _ " solid bars shown on each side of an image initial contrast level . Do not show the same when watching a standard ( 4 : 3 ) program on a stationary image for more than 15 % of your widescreen ( 16 : 9 ) TV . total TV viewing in any given week . Display constantly moving and changing images that fill the screen whenever possible . _ . News and stock - market report bars : ticker running at the bottom of the TV screen . This projection TV uses picture tubes to project the image to the screen . All picture tubes age with Shopping channel logos & pricing displays : use . As they age , their light output is gradually bright graphics that are shown constantly or reduced . Normal TV pictures fill the screen repeatedly in the same location . with constantly changing images . Under these conditions , picture tubes age at an even rate across the entire screen . This maintains Video game patterns and scoreboards a TV picture that is evenly bright over the whole screen . Stationary images or images Bright station logos : that only partially fill the screen ( leaving black moving or low - contrast graphics are less likely or colored bars to fill the screen ) , when used to cause uneven aging of the picture tubes . over extended periods of time or when viewed repeatedly , can cause uneven aging of the Online ( Internet ) websites : phosphors and leave subtle ghosts from the or any other stationary or repetitive computer stationary images in the picture . style images , including digital photos . Still or stationary images may be received from Closed Captioning broadcasters , cable channels , satellite channels , Mitsubishi recommends using a gray DVD discs , video tapes , laser discs , on - line background rather than black or a bright color services , web / Internet searching devices , video if you frequently use closed captioning . games , and digital TV tuner / converter boxes .
Page: 30
4
Page: 31
The ilPO _ . M . ielAnu System Your TV has Mitsubishi's exclusive _ [ " on - screen operating system , which provides on - screen information for menu choices and changes . A picture ( icon ) will be highlighted and can be selected using the remote control's ADJUST arrows . When selected , the appropiate menu will appear or start an automatic function . You may then make changes within the menu or access available sub - menus . A highlighted square button indicates that you may make changes to the menu screen . The _ R ® system includes the following special features : [ ] The currently selected icon or button is highlighted with a rectangular yellow outline and the text color will be yellow . [ ] On - screen instructions provide complete menu Figure 1 . MAINmenu : choice information . The first screen that appears when you press the [ ] Some on - screen menu options must be set before MENU button from your remote . other options are available . For example , " Timer Menu " will only be possible if " Clock Time " and " Set Day " have been set . The following remote control buttons will help you move quickly through the _ 1 _ ® system ( Figure 2 ) : TV MENU HOME ADJUST • or • to select the menu item you want to C ) C ) change . DEVICE MENU CANCEL ADJUST • to move to the setting field . C ) Q ADJUST • or • to change the settings . Figure2 . These buttons on your remote control are usedfor navigation within the ADJUST _ to move back to the menu item . on - screen operating system . ENTER to enter into a menu , start an automatic function , or select a checkbox . CANCEL to clear a setting , or stop an automatic function . MENU to move back one menu screen at a time . HOME to exit all menus at once and return to TV viewing .
Page: 32
Main Menu Screens : Overview SETUP Menu ( Figure 3 ) Basic ( initial ) setup instructions and functions are available through the SETUP submenu screens . • Memorize channels , • Use the NetCommand _ IR to use additional A / V devices for WS - 48413 , WS - 55413 , WS - 65413 or Input Assignment for WS - 42413 , • Set the time and day , • Select English or Spanish for the menus and on - screen display • Set the Front Button Lock ( WT - 42413 ) Figure3 . SETUP menu for WS - 48413 , WS - 55413 , • Set the Energy Mode ( WS - 48413 , WS - 55413 or WS - 65413 WS - 65413 ) . Use the setup menu when you relocate the TV , experience a power loss or when devices are added after initial setup . See pages 35 - 42 for more detailed setup information . CAPTIONS Menu ( Figure 4 ) Display broadcasted captions or text on the screen . Select the closed caption setting by choosing to display the background color as either black or translucent gray . See pages 43 - 44 for more detailed setup information . Figure 4 . CAPTIONS menu Note : Mitsubishi recommends using the translucent gray background to prevent CRT aging and / or burn - in . CHANNEL EDIT Menu ( Figure 5 ) • Customize the channel information for Ant - A and Ant - B , • Manually add or delete channels from memory , • Name channels for Ant - A and Ant - B • Add your favorite channels to a SQV ( Super Quick View TM ) list . See pages 45 - 47 for more detailed setup information . Figure 5 . CHANNEL EDIT menu ( ANTENNA )
Page: 33
Main Menu Screens : Overview , continued V - CHIP LOCK Menu ( Figure 6 ) Lock the TV by selecting times or choosing programs to block based on rating signals sent by your local broadcasting system . NOTE : For WS - 48413 , WS - 55413 or WS - 65413 set the Front Button Lock at this screen . See pages 48 - 52 for more detailed setup information . See page 48 for V - Chip rating information . Figure6 . V ChipLockMenu , WS - 48413 , WS - 55413 , WS - 65413 ADVANCED FEATURES Menu ( Figure 7 ) • Adjust colors automatically or manually , using Color Balance • Set your TV to turn on automatically • Converge ( align ) the three main colors • Display a blue screen when viewing an input with no signal • Enhance the darker parts of bright pictures See pages 53 - 57 for more detailed setup information . Figure 7 . ADVANCED FEATURES Menu AUDIO / VIDEO SETTINGS Menu ( Figure 8 ) Adjust some or all of the A / V settings . Each input can be set to your preferences . A / V Reset on the menu allows you to return the A / V settings for the current input to the factory presets . A / V Reset on the front control panel resets all inputs at one time . See pages 58 - 60 for more detailed setup information . Figure8 . Audio / VideoSettingsMenu
Page: 34
SETUP Menu : Memorize Channels , Memorize Menu , Input Assignment ( WT - 42413 ) Memorize Channels ( Figure 9 ) Select Memorize Channels for each antenna you use . The TV will find and remember strong channels and skip the unused or weaker channels . Figure 9 . Memorize Channels Menu MEMORIZE Menu ( Figure 10 ) Stop memorization at any time by pressing CANCEL . Channels memorized prior to pressing CANCEL will stay in memory . After channels are memorized , Now m _ mor ± zing all _ e _ tations you may select memorized channels in ascending or you can recei _ on _ t - A Ai _ . Please _ tand by . descending order by pressing the CHANNEL button on the remote control . Figure lO . Memorize Menu INPUT ASSIGNMENT Menu ( Figure 11 ) WT - 42413 INPUT ASSIGNMENT turns off unused inputs , turns them on again or changes the name of the input . If you turn an input Off , it will be skipped when you press DEVICE on the remote control . Choices are : [ ] ANT - A , ANT - B : On or Off [ ] DTV : Y / Pb / Pr , RGB , RGBHV or Off [ ] COMPONENT Cycle through a list of preset names or Off [ ] INPUT - l , INPUT - 2 , INPUT - 3 : Cycle through a list of preset names or Off [ ] MonitorLink ( MONLINK ) Cycle through a list of preset names or Off Figure 11 . InDut - dssignment Menu WT - 42413
Page: 35
SETUP Menu : NetCommand ® IR Setup , Language , IR Device Setup Menus ( WS - 48413 , WS - 55413 , WS - 65413 ) NetCommand IR Setup Menu ( Figure 12 ) For simple control with the Mitsubishi TV remote , select the NetCommand IR SETUP from the SETUP menu screen . There are 3 basic steps to the NetCommand IR Setup : 1 . Select the devices that are connected to the TV ( Net Command IR Device Setup Menu ) 2 . Have the _ ] [ _ Vle - arn the device's remote control keys ( NetCommand IR [ Device ] Learn menu ) 3 . Select or change the Input ( s ) the device ( s ) is ( are ) connected to ( NetCommand IR Input Assignment Menu ) Figure 12 . SETUP Menu , NetCommand ® IR Language ( Figure 13 ) On initial set up , before you can use the NetCommand IR Menus , the language for the menu screens needs to be selected . Your choices are English or Spanish ( Espafiol ) . NOTE : This Language screen only appears on initial TV setup . To change the language later , select Language from the SETUP Menu screen ( page 41 ) . NetCommand IR Menu ( Figure 14 ) Figure 13 . NetCommand ® IR Menu , Language Select NetCommand IR to start the TV learning process . 1 . NetCommand IR Device Setup Menu ( Figure 14 ) Using the Adjust buttons , select Yes for each device ( AV Receiver , Cable , DTV , etc . . . ) you have connected to the TV . After selecting Yes , press ENTER to have the WS - 48413 , WS - 55413 or WS - 65413 go to the Learn menu to start learning the device . NOTE : If you connect a cable box with an RF output other than channel 3 , please see the Channel Edit Menu on page 45 . Figure 14 . NetCommand ® IR Device Setup Menu
Page: 36
SETUP Menu : NetCommand ® IR [ Device ] Learn Menus ( WS - 48413 , WS - 55413 , WS - 65413 ) NOTE : You will need both the television remote and the device's remote to perform the Learn Menu functions . 2 . NetCommand IR [ Device ] Learn Menu NetCommand IR AVR Learn Menu ( Figure 15 ) NetCommand IR Cable ( DTV , DBS Learn Menu ( Figure 16 ) NetCommand IR DVD Learn Menu ( Figure 17 ) NetCommand IR VCR Learn Menu ( Figure 18 , page 38 ) On the NetCommand IR [ Device ] Learn menu , Figure 15 . AVR ( AV Receiver ) Learn Menu for each control ( Power , Volume , etc . . . ) on the NetCommand IR [ Device ] Learn Menu , use the Adjust buttons on the TV remote to highlight the control you want the TV to learn . Depending on the device , different control buttons will be available . Press ENTER to have the TV highlight and prepare to learn the device's individual control button . The highlighted button will start flashing . While it flashes , press the corresponding button on the device _ remote . An asterisk ( star ) will appear on - screen next to the control button name when the code is learned . To verify , press the POWER button on the TV remote to see if the device responds . After the device responds , press ENTER to return to Figure 16 . Cable Learn Menu the NetCommand IR Device Setup Menu to select the next device to learn . When all the devices are learned , select CONTINUE SETUP ( ENTER ) on the NetCommand IR Device Setup Menu to go to the NetCommand IR Assignment Menu . NOTE : If the asterisk does not appear , start the learning process again . If it does not work , your device may not be compatible to be " learned " by NetCommand . NOTE : To deselect an individual control button after it has been learned , use the Adjust buttons to highlight it , then press CANCEL on the TV remote . Figure 17 . DVD Learn Menu
Page: 37
SETUP Menu : NetCommand ® IR Input Assignment and Device Selection Menus ( WS - 48413 , WS - 55413 , WS - 65413 ) NOTE : You will need both the television remote and the device's remote to perform the Learn Menu functions . 3 . NetCommand IR Input Assignment Menu ( Figure 19 ) After learning all the individual control buttons for each device , you can change the input that each device is connected to . After selecting Continue Setup ( press ENTER ) on the NetCommand IR Device Setup menu screen , the NetCommand IR Input Assignment Menu will display . You may assign the Device to the TV or AV Receiver input at this screen . Selecting the correct oMenu inputs allows the TV to correctly switch devices . An AV Receiver typically has 4 inputs . If all inputs have been assigned , N / A will appear and that input cannot be chosen . After assigning the correct DEVICE and AVREC inputs , press HOME or MENU on the TV remote to return to TV viewing . NOTE : To program the TV's remote control for NetCommand , hold the Power button while entering the code 935 . Device Selection Menu Figure 19 . NetCommand IR Input Assignment Menu ( Figure 20 ) If your selection was Yes in the NetCommand IR Device Setup Menu ( page 36 ) , the device name will appear in the Device Selection Menu . This menu displays on - screen when you press DEVICE on the TV's remote control . A button appears next to the highlighted , selected device name . Press ENTER to use that device . If audio is through the AV Rec , you will see an icon , if there is not an icon , the audio is through the TV speakers . You may select the device whether or not the Figure20 . NetCommandlR Device Selection Menu NetCommand IR Setup Menu has been enabled .
Page: 38
SETUP Menu : Manually Setting the Clock Clock Setting ( Manual ) ( Figure 21 ) The Clock Setting menu default allows the clock time to be set manuallyo To set the clock automatically , please see page 40 . To set the clock manually , first select the current time , including AM or PM . Press • or V to slowly adjust the time . Press and hold • or • to quickly adjust the time . Figure21 . Clock Time Set Day ( Figure 22 ) After manually selecting the current time , select the current day . Figure 22 . Set Day
Page: 39
SETUP Menu : Automatically Setting the Clock Clock Setting ( Auto ) ( Figure 23 ) Set the Clock Setting to Auto to automatically set the day and time using Extended Data Service ( XDS ) time data . This data is automatically retrieved when tuned to a PBS channel or other channel in your area that provides this service . Time Zone ( Figure 24 ) Select the correct time zone ( Atlantic , Eastern , Central , Mountain , Pacific , Alaska , or Hawaii ) for your area when Auto has been selected as the Clock Setting . Figure24 . Time Zone Daylight Savings Time ( Figure 25 ) Select the Daylight Savings Time ( DST ) option that your state uses when Auto has been selected for the Clock Setting . Applies = uses DST Ignore = does not use DST The clock time and day will be set automatically after tuning to a channel carrying the Extended Data Service ( XDS ) time data ( usually your local PBS channel ) . Figure25 . Daylight Savings Time
Page: 40
SETUP Menu : Language , Front Button Lock ( WT - 42413 ) Language ( Figure 26 ) Display the on - screen menus in either English or Spanish ( Espafiol ) . The first time you powered On your TV , you were requested to select an on - screen menu language . If you choose to change the selection , all menu text will immediately switch to the language of your choice . Figure 26 . Language / Idioma Front Button Lock for WT - 42413 ( See V - Chip Menu for other models ) ( Figure 27 ) Disable controls on the front panel to prevent anyone from accidentally changing settings . Select On to lock out the operations of the front panel button and select Off to restore the operations of the front panel buttons . If the front panel buttons have been locked and you misplace the remote control , you can restore the function of the front panel buttons by pressing and Figure 2Z Front Button Lock for WT - 42413 holding the MENU button on the front panel for more than 8 seconds . If the TV is already on , a message will be displayed to confirm the release of the Front Button Lock .
Page: 41
SETUP Menu : Energy Mode ( WS - 48413 , WS - 55413 , WS - 65413 ) Energy Mode ( Figure 28 ) This feature is only for models WS - 48413 , WS - 55413 and WS - 65413 . Change the setting to Low ( less than 1 watt ) when you want the TV to operate in an energy saving mode when it is turned off . If the Energy Mode is set to Low , it will not be possible to record while the TV's power is off because there will be no signal from LOOP OUT ( on the TV back panel ) to the VCR and / or cable box . NOTE : The Standard setting has a faster turn on Figure 28 . Energy Mode for WS - 48413 , WS - 55413 , WS - 65413 time , but uses more power than the Low setting . Standard is recommended .
Page: 42
CAPTIONS Menu : Overview CAPTIONS Menu ( Figure 29 ) Turn On or Off the closed caption decoder , select the type of captions or text , and choose black or translucent gray as the background color for the closed caption area . Broadcasters can send either Standard or Text closed captioning . Standard closed captioning follows the dialogue of the characters on - screen and displays in a small section of the screen . Figure29 . CAPTIONS menu Text closed captioning often contains information such as weather or news and covers a large portion of the on - screen program . Your TV can decode four different standard and four different text closed captioning signals from each TV station . However , each TV station may broadcast only one or two closed captioning signals , or none at all . NOTE : Mitsubishi recommends using the translucent gray background to prevent CRT aging and / or burn - in .
Page: 43
CAPTIONS Menu : Closed Captions , Background Color Closed Captions ( Figure 29 ) Display one of the following types of Closed Captions : CC1 , CC2 , CC3 , or CC4 : Standard closed captioning signals . _ . Textl , Text2 , Text3 , or Text4 : Text dosed captioning signals . _ . On if mute : Closed captions when mute . When selected , the standard dosed captioning signal ( CC1 ) will turn on / off by pressing the MUTE button on the TV remote control . _ . Off : No dosed captions . Figure29 . Closed Captions CC Background ( Figure 30 ) Display the background color as either black or translucent gray , to make the closed captions easier to read . NOTE : Mitsubishi recommends using the translucent gray background to prevent CRT aging and / or burn - in . Figure 30 . CAPTIONS menu
Page: 44
CHANNEL EDIT Menu : Antenna , Channel Selection Antenna ( Figure 32 ) Select Ant - A or Ant - B . For each antenna , you can add or delete channels in memory , name channels , and add channels to the SQV ( Super Qgick View TM ) list . Figure 32 . Antenna Channel ( Figure 33 ) Select to edit the channel selections . You can add or delete from memory , name , or add to the SQV ( Super Qgick View TM ) list . After selecting Channel , editing can be done using the Adjust buttons or entering the 3 digit channel number you want to change ( Example 002 for channel 2 ) . For WS - 48413 , WS - 55413 and WS - 65413 , during NetCommand ® IR setup , if you connected a cable box with an RF output other than channel 3 you can use the Channel Edit menu to tune the TV to the correct channel . Figure 33 . C ] ) annel Change Antenna from Air to Cable . Then for the Channel , select 004 or 005 , depending on your cable box requirement . The channel you select in this menu will be the fixed channel used with your cable box .
Page: 45
CHANNEL EDIT Menu : Memory , Name Selection Memory ( Figure 34 ) Add weaker channels viewed with Ant - A or Ant - B and delete unwanted channels , after all available channels have been memorized with Memorize Channels ( page 35 ) . Use the CH ( channel ) button on the remote control to view memorized channels . Figure 34 . Memory Name ( Figure 35 ) Name channels shown on Ant - A or Ant - B ( up to four characters ) . After you enter a name , it will appear on the TV screen next to the channel number . 1 . Select Ant - A or Ant - B . 2 . Select the memorized channel you want to name . 3 . Press ADJUST until you see the underline highlighted in the Name field . 4 . Use ADJUST • or • to select letters A - Z , numbers 0 - 9 , and ! or symbols ( ! . & ' ! : * - and blank ) for each character of the name you would like for the selected channel . Dess ENTER after choosing each letter and after the name is complete . If you want to change your selection while on the option Figure 35 . Name field , use CANCEL to delete the currant character . You will move one position back . If you press CANCEL while at the first character , the entire name will be deleted .
Page: 46
CHANNEL EDIT Menu : Using SQ . V ( SuperQuickViewTM ) Using The Menu Screen ( Figure 36 ) Put together a list of your favorite channels from Ant - A and Ant - B using SQ _ V ( Super Qgick View ) . Store up to 6 channels in each of the 9 different memory banks . After adding a channel to the SQV memory , " SQ _ V " will appear under the channel number on the TV screen . To change SQV choices using the menu : 1 . Press A or • when at Channel settings or use the CHANNEL button on the remote control to select the channel you wish to add or delete from a SQV Fig . _ 36 . SQV ( S _ pe _ Q _ i _ Vie _ TM ) memory bank . 2 . Press I _ when at SQV in the menu to move the selector to the On ! Off setting . 3 . Press A or • when at SQV setting to select the SQV memory bank you wish to modify . 4 . Dess ENTER to add ( On ) or delete ( Off ) the current channel from the SQV memory bank that you have selected . TM Figure 37 . SQV ( Super Quick View 9 button on the remote control Using The Remote Control ( Figure 37 ) View and add SQV channels using the remote control : 1 . Use the CH ( channel ) or number buttons to select the channel you want to add . 2 . Press and hold the SQV button for about 3 seconds . When " SQV " and the memory bank number appear under the channel number , the channel has successfully been added . To change the SQV banks using the remote control : 1 . Press the SQV button . 2 . To change memory banks , press a number button within 5 seconds while the SQV button is on - screen . Remove SQV channels using the remote control : 1 . Press the SQV button repeatedly until you see the desired channel . 2 . While the channel number and SQV indicator are still displayed on the screen , press the CANCEL button . If the CANCEL button is not pressed before the SQV indicator disappears , the channel will not be removed . 3 . When the SQV indicator disappears , the channel has successfully been removed .
Page: 47
V - CHIP LOCK Menu : Overview V - Chip Signal Information When provided by the broadcaster , V - Chip ratings can be used to control which programs can be viewed or will be blocked . When V - Chip ratings are sent , you will see the ratings when you change the channel or when you press the INFO button on the remote control . Both TV and Movie ratings will display . TV ratings apply to programs and movies developed for TV and may have supplemental blocking by content categories . Movie ratings use MPAA ratings for movies released in theaters . V - CHIP EXCEPTIONS : TV Ratings : Used with TV programs and Made - for - TV movies . TV Rating FV D L S V TV - Y Youth , for children under the age of 7 . TV - Y TV - Y7 Youth , 7yearsoldandolder . l _ rchildren7yearsoldandolder . TV - Y7 X TV - G General Audience . For the entire family to view . TV - PG X X X X TV - PG Parental Guidence . Parental Guidence is recommended , may not be suitable for some children . TV - 14 X X X X TVq4 Adolescent 14years old and older . Not recommended for children TV - MA X X X under the age of 14 . TV - MA Mature Audience . For adults only . Content Categories : Used in association with the TV ratings above . FV Fantasy Violence - applies to TV - Y7 only . D Sexual Dialog - applies in different degrees to TV - PG and TVq4 . L Adult Language - applies in different degrees to TV - PG , TVq4 , and TV - MA . S Sexual Situations - applies in different degrees to TV - PG , TVq4 , and TV - MA V Violence ( graphic or realistic ) - applies in different degrees to TV - PG , TVq4 , and TV - MA . When you select a TV rating , you are selecting the least - restriced program level that can be viewed . As an example , if you select TV - PG , you are allowing programs rated TV - Y , TV - Y7 , TV - G and TV - PG to be seen and blocking programs rated TV - 14 and TV - MA . When you select a TV Content category , you will block all TV programs that have the same content category listing . As an example , if you select to block V ( Violence ) at the TV - 14 level , you * , / 111also block any program that has the V category listing at the TV - PG rating level as well . Movie Ratings : Used with theater released movies and direct - to - video movies . G General Audience - Designed for the entire family m view . PG Parental Guidence - Parental Guidence is recommended , may not be suitable for some children . PGq3 Parental Guidence 13 years dd and older - Not recommended for children under the age of 13 . R Restricted - Restricted in the theater to 17years old and older unless accompanied by an adult . NCq7 No Children - Restricted in the theater to 18 years dd and older . X Adult - Designed for and restricted in the theater m adult audiences only . When you select a Movie rating , you are selecting the least restricted program level that can be viewed . As an example , if you select a movie rating of PG - 13 , you are allowing movies rated G , PG and PG - 13 to be seen and blocking movies rated R , NC - 17 , and X . Programs Not Rated : Used for programs that are not rated like news , sports , weather , emergency bulletins , or movies such as those prior m or without MPAA Ratings . This does not include programs without V - Chip signals
Page: 48
V - CHIP Menu : Setting Up and Using V - Chip Lock Passcode Setting Up the V - CHIP LOCK Passcode ( Figure 38 ) Select V - CHIP LOCK from the MAIN menu for first time setup or after you have canceled your passcode . You will see the screen shown in Figure 38 . Use the number buttons on the remote control to input a new four - digit passcode , then press ENTER . Before pressing ENTER , you can delete a character and move back one character by pressing CANCEL , Figure38 . First time entry to the V - CHIP LOCK al ! or leave the passcode screen by pressing MENU or models HOME . Entering the Passcode ( Figure 39 ) Input your passcode as shown in Figure 39 ( Note : Text changes from " a new " to " your " passcode ) . The next time you select V - CHIP LOCK from the MAIN menu , you will see this screen . Figure39 . Re - entry to the V - CHIP LOCK all models
Page: 49
V - CHIP Menu ( WT - 42413 ) : Allowing or Blocking Ratings , Locking by Hour or Time Allowing or Blocking by Ratings ( Figure 40 ) Block or Allow programs based upon rating signals sent by the broadcasting station . The factory preset for TV Ratings is TV - PG ( Parental Guidance ) allowing only programs rated TV - PG or lower . The factory preset for Movies is PG , allowing only movies rated PG or lower . Please refer to page 48 for a detailed ratings description . Figure 40 . V - CHIP LOCK Choices WT - 42413 V - CHIP HOURS / LOCK BY TIME ( Figure 41 ) V - CHIP HOURS / LOCK BY TIME will allow you to activate the V - Chip or lock the entire TV during specific hours . V - CHIP Start Time and V - CHIP Stop Time ( Figure 41 ) Select the times you would like the V - Chip to be Active . By setting the V - Chip Start Time and V - Chip Stop Time to the same time , the V - Chip will be active 24 hours a day . Press A or • to slowly adjust the time . Press and hold A or • to quickly adjust the time . Figure 41 . V - CHIP HOURS / LOCK BY TIME WT - 42413 Lock by Time , Lock Time , and Unlock Time ( Figure 41 ) Lock by Time locks the entire TV when Lock by Time is On and you have selected a Lock Time and Unlock Time . Your TV continues to be locked until you input your passcode , or when the locked time expires .
Page: 50
V - CHIP Menu ( WS - 48413 , WS - 55413 , WS - 65413 ) : Locking by Time , Front Button Lock , Selecting V - Chip Rating Menu LOCK by Time ( Figure 42 ) Select On at Lock by Time , then select the Lock Time and Unlock Time . This will lock the entire TV . Your TV continues to be locked until you input your passcode , or when the locked time expires . Figure42 . V - CHIPLOCKMenu Lock by Time Front Button Lock ( Figure 43 ) Setting the Front Button Lock to On will disable controls on the front panel to prevent anyone from accidentally changing settings . Offwill restore the operations of the front panel buttons . If the front panel buttons have been locked and you misplace the remote control , you can restore the function of the front panel buttons by pressing and holding the MENU button on the front panel for more than 8 seconds . If the TV is already on , a message will be displayed to confirm the release of the Front Button Lock . Figure 43 . Front Button Lock Selecting V - Chip Rating Menu ( Figure 44 ) To block or allow programs based on the rating system described on page 48 , select V - Chip to go to the V - Chip Rating menu . Figure 44 . Selecting V - Chip Rating Menu
Page: 51
V - CHIP Menu ( WS - 48413 , WS - 55413 , WS - 65413 ) : Allowing or Blocking Ratings , Lock by Time Allowing or Blocking by Ratings ( Figure 45 ) Block or Allow programs based upon rating signals sent by the broadcasting station . The factory preset for TV Ratings is TV - PG ( Parental Guidance ) allowing only programs rated TV - PG or lower . The factory preset for Movies is PG , allowing only movies rated PG or lower . Please refer to page 48 for a detailed ratings description . V - CHIP HOURS ( Figure 46 ) Figure 45 . Ratings Menu , W8 - 48413 , WS - 55413 , V - CHIP HOURS will allow you to activate the V - W8 - 65413 Chip or lock the entire TV during specific hours . To set V - Chip Hours , select V - CHIP Hours from the V - CHIP LOCK menu . V - CHIP Start Time and V - CHIP Stop Time ( Figure 46 ) Select the times you would like the V - Chip to be Active . By setting the V - Chip Start Time and V - Chip Stop Time to the same time , the V - Chip will be active 24 hours a day . Press A or • to slowly adjust the time . Press and hold A or • to quickly adjust the time . Figure 46 . Selecting V - Chip Rating Menu W8 - 48413 , W8 - 55413 , WS - 65413
Page: 52
ADVANCED FEATURES Menu : Color Balance , Auto Color Correction , PerfectColor TM , Reset Color Color Balance Menu ( Figure 47 ) Your Mitsubishi TV uses six colors ( Magenta , Red , Yellow , Green , Cyan and Blue ) to create Color Balance . You may adjust these colors automatically or manually or reset them to the default settings . Auto Color Correction ( Figure 48 ) Set the Auto Color Correction option to On to optimize skin tone color automatically and continuously . Both Manual Color Adjustment and Reset Color options are grayed out and unavailable when On is selected for Auto Color Correction . Figure 4Z ADVANCED FEATURES Menu PerfectColor ( Figure 49 ) Press ENT to display the menu for manual color adjustment . Individual sliders for Magenta , Red , Yellow , Green , Cyan and Blue will be displayed . The sliders have a numeric value , where 63 is the maximum . The default setting for each color is 31 ( center ) . Highlighted text will show which slider you are adjusting . • For WT - 42413 , all inputs are adjusted at once . This feature is only available with the 480i signal . • For WS - 48413 , WS - 55413 or WS - 65413 , each active input can be individually adjusted . Figure 48 . COLOR BALANCE Menu Press Adjust • or • to navigate between colors and Adjust • or • to change the color slider settings . The PerfectColor option is only available when Auto Color Correction is turned Off . Reset Color ( Figure 48 ) Select to reset the PefectColor settings . • For WT - 42413 , all inputs are reset at once . Figure49 . PerfectColor Menu • For WS - 48413 , WS - 55413 or WS - 65413 , each active input can be individually reset .
Page: 53
ADVANCED FEATURES Menu : TIMER , Timer Menu , and Set Time TIMER ( Figure 50 ) The timer will automatically turn the TV on ( if it is off ) at the time you schedule and select . When Ant - A or Ant - B is the selected input , you may select any memorized channel . The TV will tune to this channel when the timer turns it on . Figure 50 . ADVANCED FEATURES menu TIMER menu ( Figure 51 ) The timer can be turned On or Off . When On , you need to select the time and the day to turn On and the input and channel to display . At your preselected time , the timer will turn the TV on and a message will be displayed , " Press a key for the TV to stay on . " Any button on the remote control must be pressed within 5 minutes or the TV will turn itself off . FigureS1 . TIMER menu ( Timer ) Set Time ( Figure 52 ) Select the hour and minute , including AM or PM , when the TV is to turn on . Press • or • to slowly adjust the time . Press and hold • or • to quickly adjust the time . Figure 52 . TIMER menu ( Set Time )
Page: 54
ADVANCED FEATURES Menu : Set Day , Input , and Channel Set Day ( Figure 53 ) Select the days that the TV will turn on automatically . You can select Everyday , Mon - Fri ( Monday through Friday ) , or the individual days of the week . Figure 53 . TIMER menu ( Set Day ) Input ( Figure 54 ) Select the input to use when the timer turns on the TV . If the TV is already on , the timer will turn the TV to this selected input . Figure54 . TIMER menu ( Input ) Channel ( Figure 55 ) If the selected input is for Ant - A or Ant - B , the timer will turn the TV to the selected channel . Figure 55 . TIMER menu ( Channel )
Page: 55
ADVANCED FEATURES Menu : CONVERGENCE CONVERGENCE Menu ( Figure 56 ) Your Mitsubishi TV has three picture tubes which are aligned to properly converge the projected light beams on the screen . Each picture tube projects a single color of red , blue or green . During production , your TV was carefully adjusted to properly align these colors . As a special feature , you have the ability to adjust the red and blue light beams in reference to the fixed green light beam . This process is called convergence . Convergence aligns the entire screen at once . Select either Red Convergence or Blue Convergence to begin alignment . Figure 56 . CONVERGENCE menu Convergence Screen ( Figure 57 ) When the Red and Blue crosshairs are properly converged , the center - screen crosshairs will appear white . You can use A , V , ' , or • to move the Red and Blue crosshairs . Press VIDEO to switch between Red and Blue . Press AUDIO for the Advanced Convergence screen . Advanced Convergence ( Figure 58 ) After adjusting the Red Convergence and Blue Figure 57 . Convergence screen Convergence , you can fine - tune your TV by adjusting the Red and Blue convergence at 64 individual points . Move the flashing bracket to a position needing adjustment by pressing A , ! , ' , or • . Press ENT to select the position ( flashing will stop ) . Move the Red or Blue line by pressing A , V , _ , or • . Press VIDEO to switch between the Red and Blue lines . A position is properly converged when all three lines combine to appear white . Press ENT to deselect the position ( flashing will resume ) , and move the brackets to the next position needing adjustment . When completed , press MENU to save your changes , and exit the Advanced Convergence screen . NOTE : This is considered a fixed image . Please see Important Notes on pages 6 , 30 or 75 . Figure 58 . Advanced Convergencescreen
Page: 56
ADVANCED FEATURES Menu : Reset Convergence , Video Mute , Black Enhancement RESET FACTORY DEFAULTS ( Figure 59 ) If you do not want to reset the convergence , press the MENU key to return to the Convergence menu without performing a reset . You may reset the red and blue convergence to factory default settings when you first use your TV or after making manual changes . Press the ENTER key to restore the convergence to the default settings . All the changes you made manually will be deleted . The message " Convergence Completed " appears when the Figure 59 . RESET to Factory Defaults convergence reset process ends . Video Mute ( Figure 60 ) Video Mute , when On , lets you display a blue background when no signal is being received on Inputs 1 - 3 , DTV , and Component 1 - 2 ( Component only for WT - 42413 ) and MonitorLink . Figure 60 . Video Mute Black Enhancement ( Figure 61 ) The contrast in dark scenes is enhanced for better picture quality . Brighter scenes will not be affected . Figure 61 . Black Enhancement
Page: 57
AUDIO / VIDEO SETTINGS Menu : Overview AUDIO / VIDEO SETTINGS Menu ( Figure 62 ) Each input has its own A / V memory . You can adjust each input's A / V memory in two ways , using either the menu or the remote control . A / V Memory Reset A / V Memory Reset will return the currently selected input's A / V memory to the factory settings . To reset an input's A / V memory , select A / V Memory Reset , select the input you want to reset , and press ENTER . TV Speakers This selection will turn on or off the TV _ internal Figure 62 . AUDIO / VIDEO SETTINGS menu speakers . You may select Offwhen sending the sound through a separate stereo system or surround sound A / V receiver . Audio Output Select Fixed if your audio receiver or stereo system can be controlled with a remote . This allows you to adjust the volume with the system's remote control or the TV remote control , if compatible . This setting is better for surround sound receivers . Select Variable if your audio receiver or stereo system cannot be controlled with a remote . This allows the TV's internal circuitry to adjust the volume . AUDIO SEq _ NGS and VIDEO SEq _ NGS ( Figure 63 ) After selecting AUDIO SETTINGS or VIDEO SETTINGS , you can adjust the settings by pressing A , V , ' I , or • . For descriptions of the individual A / V settings , see AUDIO / VIDEO Setting Descriptions , pages 59 - 60 . Figure 63 . AUDIO SETTINGS Using the AUDIO and VIDEO Buttons on the Remote Control 1 . Press AUDIO or VIDEO to cycle through the available settings . 2 . Press _ or • to adjust the setting . After 5 seconds of inactivity , the setting display will disappear .
Page: 58
AUDIO / VIDEO Setting Descriptions : Audio signal is broadcast , the letters " SAP " will be Audio Settings displayed when you tune to the channel . [ ] Bass • Mono : Reduces background noise and should Enhances or reduces low frequency sound . be used when receiving a weak stereo audio [ ] Treble signal . All audio will be played mono with Enhances or reduces high frequency sound . this setting . [ ] Balance [ ] Listen to ( for INPUTs ) Is not available . Adjusts the level of sound between the left and right speakers . [ ] Level Sound [ ] Surround Automatically equalizes the volume level Creates simulated stereo and surround effects . of programs containing significant level Your choices are : differences from one segment to another ( for example , regular programming to • Off : No surround effects . Use this setting commercials ) . To receive the best fidelity with when using an A / V receiver with Dolby TM music programs , you can turn this setting to Pro Logic Surround , or Dolby TM Digital Off . Surround . • Simulated Stereo : Your TV will create a NOTE : A slider will display on - screen for each simulated stereo effect when watching a non - setting . The slider has a numeric value , where 63 is stereo program . the maximum , the mid - range is 31 and the minimum • Surround Sound : Your TV will create a setting is 0 . simulated surround effect when watching a stereo program . [ ] Listen to ( for Ant - A and Ant - B ) Determines how your TV will receive a broadcast audio signal and play back the sound you hear . Your choices are : Stereo : Default setting . The TV will play stereo broadcasts in stereo and mono broadcasts in mono . The word " Stereo " will be displayed when you tune to a channel broadcasting stereo . SAP ( Second Audio Program ) : Additional monaural soundtrack that you cannot hear during normal TV viewing . The SAP signal might be related to the program you are watching , such as a soundtrack in a foreign language , or unrelated to the program you are watching such as a weather report . If a SAP
Page: 59
AUDIO / VIDEO Setting Descriptions : Video Video Settings [ ] Contrast Video Noise Provides a slider to adjust the white - to - black NOTE : This function operates only in 480i mode . level . Low contrast shows a variety of shades Reduces minor noise ( graininess ) in the in darker images , while high contrast shows broadcast or input signal . darker images more uniformly black and makes colors appear more vibrant . [ ] Film Mode ( Automatic ) NOTE : This function operates only in 480i mode . [ ] Brightness Video media uses a video camera created at Provides a slider to adjust the overall 30 frames per second . Film media uses a brightness of the picture . film camera created at 24 frames per second . Examples of video media are live TV broadcast [ ] Sharpness such as news , special events , or video taped Provides a slider to adjust the detail and clarity . programs . Examples of film media are motion pictures , made - for - TV movies , and many prime time programs . Filmed media is [ ] Color converted by the broadcaster or home video Provides a slider to adjust the color intensity . company to 30 frames per second to match TV or video standards . This conversion can leave subtle " picture artifacts " or conversion errors . [ ] Tint The settings are On and Off . If you select On , Provides a slider to adjust the proportion of red the system automatically detects if the signal to green . source is Film and corrects for conversion errors . If you select Off , the system will never correct for conversion errors . [ ] Color Temp ( Color Temperature ) Allows you to adjust how white images are displayed . Your choices are : DefinEdge VSM Low 6500K or Low ( for DTV ) : White Turns on the velocity scanning modulation images will have a warm cast to them . This and emphasizes the edges of screen images . adjustment is an average and can vary due to Able to increase or decrease edge sharpness . ambient room lighting , video scene brightness Turn On to increase and Off to decrease edge and the TV's age . The Low 6500K represents sharpness . the 6500K industry standard for NTSC ( non - DTV ) pictures . NOTE : A slider will display on - screen for each setting . The slider has a numeric value , where 63 is the maximum , the mid - Medium : White images will be balanced range is 31 and the minimum setting is 0 . between the Low ( warm ) and High ( cool ) settings . NOTE : For optimal picture performance , it is recommended that you adjust your video settings ( specifically contrast and • High : White images will have a cool cast to brightness ) during initial setup . Certain factors will affect your them . This setting may provide the most perosonal preverences , inchtding room lighting , glare reflections realistic picture under bright lighting . and viewing angels / distance . This also slows phosphor aging .
Page: 60
5 Appendix B : HD Input Appen _ C : Remote Control Programming Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Appendix E : Diamond Shield TM Installation and Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Warrantv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79