Home | Register Login | Wanted Manuals | MarketPlace | Members Area | Manuals Manufacturer Directory | UPC Lookup | Information Pages | Policy


Back To Troy-Bilt Tiller - Cultivator       Model: 21A148H063 Troy-Bilt Tiller Edger Owners Manual
Regular Text Search or Search by Model Number

Register / log-in to add to your Hammerwall Collection.
Manual Location


This is a partial text extraction from the pdf, to download the pdf, click the Manual tab. If you want to search this text, hold control and F, and type the word you are looking for.

Page: 1

Operator’s Manual Tiller / Edger Model 148H IMPORTANT:READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning : This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest - covered , brush - cov - ered or grass - covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws ( if any ) . If a spark arrester is used , it should be maintained in effective working order by the operator . In the State of California the above is required by law ( Sec - tion 4442 of the California Public Resources Code ) . Other states may have similar laws . Federal laws apply on federal lands . A spark arrester for the muffler is available by contacting the service department at Troy - Bilt LLC , P.O . Box 361131 Cleveland , Ohio 44136 - 0019 . TROY - BILT LLC , P.O . BOX 361131 , CLEVELAND , OH 44136 - 0019 PRINTED IN USA FROM NO . 770 - 10600 ( 12 / 2001 )
Page: 2

TABLE OF CONTENTS Content Page Calling Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Features and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Warrany Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover FINDING MODEL NUMBER This Operator’s Manual is an important part of your new Tiller / Edger . It will help you assemble , prepare and maintain the unit for best performance . Please read and understand what it says . Before you start assembling your new equipment , please locate the model plate on the equipment and copy the infor - mation from it in the space provided below . This information is very important if you need help from our Customer Support Department or an authorized dealer . • You can locate the model number by looking at the rear surface of the tine shield . A sample model plate is ex - plained below . For future reference , please copy the model number and the serial number of the equipment in the space below Copy Model Number Here TROY - BILT LLC Copy Serial Number Here P . O . BOX 361131 CLEVELAND , OH 44136 www.troybilt.com 330 - 558 - 7220 866 - 840 - 6483 ENGINE INFORMATION The engine manufacturer is responsible for all engine - related issues with regards to performance , power - rating , speci - fications , warranty and service . Please refer to the engine manufacturer’s Owner’s / Operator’s Manual packed sepa - rately with your unit for more information . CALLING CUSTOMER SUPPORT If you have difficulty assembling this product or have any questions regarding the controls , operation or maintenance of this unit , please call the Customer Support Department . Call 1 - ( 330 ) 558 - 7220 or 1 - ( 866 ) 840 - 6483 to reach a Customer Support representative . Please have your unit’s model number and serial number ready when you call . See previous section to locate this in - formation . You will be asked to enter the serial number in order to process your call . . For more details about your unit , visit our website at www.troybilt.com 2
Page: 3

Section Safety 1 This machine meets voluntary safety standard B71.8 – 1996 , which is sponsored by the Outdoor Power Equipment Institute , Inc . , and is published by Safety Alert Symbol the American National Standards Institute . This is a safety alert symbol . It is used in this manual and on the unit to alert you to potential haz - ards . When you see this symbol , read and obey the WARNING message that follows it . Failure to obey safety mes - sages could result in personal injury or property damage . The engine exhaust from this product contains chemi - cals known to the State of California to cause cancer , birth defects or other reproductive harm . d . Fill fuel tank outdoors and with ex - • Do not operate this equipment if you are TRAINING treme caution . Never fill fuel tank under the influence of alcohol , medication , • Read this Owner’s Manual and the sep - when indoors . Use a funnel or or when you are tired or ill . arate Engine Owner’s Manual very care - spout to prevent spillage . fully before operating this equipment . Be PREPARATION e . Replace all fuel tank and fuel con - completely familiar with the controls and tainer caps securely . • Thoroughly inspect the area where the the proper use of the equipment . Know equipment is to be used and remove all how to stop the unit and disengage the f . If fuel is spilled , do not attempt to foreign objects . controls quickly . A replacement Manual start the engine , but move the ma - is available by contacting your authorized chine away from the area of spillage • Make sure that the Throttle / Tines Con - dealer or the Factory . and avoid creating any source of ig - trol Lever is disengaged and is in the neu - nition until fuel vapors have tral position before you begin to start the • Never allow children or untrained dissipated . engine . adults to use this equipment . Let adults operate the unit only if instructed • Do not operate the machine without • Never make adjustments to your equip - properly . wearing adequate outer garments . Avoid ment when the engine is running or spark loose garments or jewelry that could get plug wire is connected ( unless specifically • Keep the area of operation clear of all caught in moving parts of the machine or recommended in Owner’s Manual ) . persons , particularly small children and its engine . pets . Keep bystanders at least 25 feet from the area of operation . • Do not operate the equipment when OPERATION barefoot or when wearing sandals , • Keep in mind that the operator or user sneakers , or similar lightweight footwear . is responsible for accidents or hazards Operator’s Position Wear protective footwear that will protect occurring to other people , their property your feet and improve footing on all and themselves . surfaces . • Familiarize yourself with all of the • Wear approved safety glasses when op - safety and operating decals on this equip - erating this equipment . The operation of ment and on any of its attachments or any powered machine can result in for - accessories . eign objects being thrown by high - speed • Do not run engine in an enclosed area . RIGHT SIDE rotating parts . Engine exhaust contains carbon • Do not till near underground electric monoxide gas , a deadly poison that is cables , telephone lines , pipes , or hoses . odorless , colorless , and tasteless . Do not If in doubt , contact your utility or tele - LEFT SIDE operate this equipment near buildings , phone company to locate underground windows , or air conditioning equipment . services . LEFT and RIGHT sides of the tiller are • Do not allow hands or any other part of • Handle fuel with care . It is highly from the operator’s position behind the the body or clothing near the rotating flammable and has explosive vapors . handlebars ( unless noted otherwise ) . tines or near any other moving part . The Take these precautions : tines begin to rotate forward once the a . Use an approved fuel container . engine is started and the Throttle / Tines • The correct operator’s position is when Control Lever is squeezed . The tines con - b . Add fuel before starting the engine . you are standing behind and gripping the tinue to rotate until the operator releases Never remove the cap of the fuel handlebar , facing forward toward the the Throttle / Tines Control Lever . tank or add fuel while the engine is engine . Do not leave this position while running or when the engine is hot . using the engine Throttle / Tines lever . • Before inspecting or servicing any part Operators shall not smoke . of the equipment , shut off engine , make • Do not put hands or feet near or under sure all moving parts have come to a c . Keep matches , cigarettes , cigars , rotating parts . complete stop , then disconnect spark pipes , open flames , and sparks plug wire from spark plug and move wire away from the fuel tank and fuel away from the plug . container . 3
Page: 4

Section 1 : Safety • Exercise extreme caution when on or • Be aware that the equipment may unex - • Do not touch engine parts which may crossing gravel drives , walks or roads . pectedly bounce upward or jump forward be hot from operation . Allow parts to Stay alert for hidden hazards or traffic . if the tines should strike extremely hard cool before inspecting , cleaning or Do not carry passengers . packed soil , frozen ground , or buried ob - repairing . stacles such as large stones , roots or • After striking a foreign object , stop the • Remember : you can stop the tines by stumps . If you are in doubt about the engine , let all moving parts come to a releasing the engine Throttle / Tines lever . tilling conditions , always use the fol - complete stop , disconnect the spark plug Move the engine On / Off switch to OFF to lowing operating precautions to assist wire and prevent it from touching the shut the engine off . you in maintaining control of the spark plug , then carefully inspect the ma - • Never transport this machine when the equipment : chine for damage . Repair the damage engine is running . before restarting and operating the a . Stand behind the equipment , using • Terminals and non - insulated electrical machine . both hands on the handlebars . parts shall be protected against shorting Relax your arms , but use a secure • Exercise caution to avoid slipping or during normal servicing , refueling or hand grip . falling . lubrication . b . Start tilling at shallow depths , • If the machine should start to vibrate • Use extreme caution when reversing or working gradually deeper with each abnormally , stop the engine . Disconnect pulling the machine toward you . pass . the spark plug wire and prevent it from • Start the engine carefully according to touching the plug . Check immediately for c . Clear the tilling area of all large instructions and with feet well away from the cause . Vibration is generally a stones , roots , and other debris . the tines . warning of trouble . Fix the problem d . In an emergency , stop the tines by before using the equipment again . releasing the engine Throttle / Tines • Stop the engine , disconnect the spark lever on the handlebar . To stop the MAINTENANCE / STORAGE plug wire and prevent it from touching the engine , move the engine On / Off • Keep the tiller , attachments and acces - spark plug whenever you leave the equip - switch to OFF . sories in safe working condition . ment , before unclogging the tines , or • Do not overload the machine’s capacity when making any repairs , adjustments or • Check all nuts , bolts , and screws at fre - by attempting to till too deeply at too fast inspections . quent intervals for proper tightness to be a rate . sure equipment is in safe working • Take all possible precautions when • Never operate the equipment on slip - condition . leaving the machine unattended . Always pery surfaces . Look behind and use care stop the engine . Disconnect the spark • Never store equipment with fuel in fuel when backing up . plug wire and prevent it from touching the tank inside a building where fumes may • Do not operate the equipment on a plug . reach an open flame or spark ( hot water slope that is too steep for safety . When and space heaters , furnaces , clothes • Before cleaning , repairing , or on slopes , slow down and make sure you dryers , stoves , electric motors , etc . ) . inspecting , stop the engine and make have good footing . certain all moving parts have stopped . • Allow the engine to cool before storing • Never allow bystanders near the unit . Disconnect the spark plug wire and the equipment . prevent it from touching the spark plug to • Only use attachments and accessories • Keep the engine free of grass , leaves , avoid accidental starting . that are factory - approved . or grease to reduce the chance of a fire • Never operate equipment without • Never operate the equipment without hazard . proper guards , plates , or other protective good visibility or good light . • Store gasoline in a cool , well - ventilated safety devices in place . • Never operate the unit if you are tired , area , safely away from any spark - or • Do not run the engine in an enclosed or under the influence of alcohol , drugs , flame - producing equipment . Store gaso - area . The exhaust fumes from the engine or medication . line in an approved container , safely away contain extremely dangerous carbon from the reach of children . • Do not tamper with the engine gov - monoxide gas . This gas is colorless , ernor settings on the machine ; the gov - • Never perform maintenance when odorless , tasteless and deadly poisonous . ernor controls the maximum safe oper - engine is running or spark plug wire is • Keep children and pets away . ating speed and protects the engine and connected unless instructed to do so . all other moving parts from damage • If fuel tank must be drained , do so out - caused by engine overspeed . Authorized doors . service shall be sought if a problem • Follow manufacturer’s recommenda - exists . tions for safe loading , unloading , trans - port and storage of machine . 4
Page: 5

Section Assembly 2 STEP 2 : Inspect and Tighten Hardware WARNING Check all nuts , bolts and screws on your unit and tighten as To prevent personal injury or property damage , do not start needed . the engine until all assembly steps are complete and you have read and understand the safety and operating instruc - Tools Needed to Check for Loose Hardware : tions in this manual . • Adjustable wrench • Slotted - head screwdriver • Phillips - head screwdriver INTRODUCTION • 7 / 16 " socket and extension Carefully read these instructions in their entirety before you ( to check hardware at ends of handlebar ) attempt to assemble or operate your new equipment . The Border Edger Attachment ( D , Figure 1 ) does not need to STEP 3 : Add Motor Oil to Engine be installed until you are ready to do edging projects ( refer to IMPORTANT : The engine is shipped without oil in the instructions in Section 4 ) . crankcase . Do not start the engine without first adding motor oil . Severe engine damage will result if the engine is run UNPACKING INSTRUCTIONS without motor oil . 1 . Inspect your machine immediately . If you find or suspect 1 . Refer to the separate Engine Owner’s Manual for motor oil damage to the carton or contents , contact your local autho - specifications and capacities . rized dealer or the Factory for assistance . 2 . Add oil as described in the Engine Owner’s Manual ( the 2 . Remove any packing material . Check for loose parts engine is a vertical type , GX 31 model ) . before discarding the packing material or carton . Loose parts include the following : ( 1 ) Wheel ( for edging ) ( 1 ) Edger Tine ( 2 ) * Long Bushings D C ( 1 ) * Short Bushing * Packed in a separate plastic bag . 3 . Perform the assembly on a clean , level surface . Be careful B not to severely bend any of the control cables on the unit . C ASSEMBLY STEPS STEP 1 : Unfold and Adjust Handlebars IMPORTANT : Be careful not to pinch any control cables . C Push the cables out and away before swiveling the handle - bars . 1 . Loosen the two handlebar knobs ( A , Figure 1 ) and unfold C A the handlebars into the operating position . Do not use force — if there is binding , continue to loosen the knobs . A C 2 . There are two height setting holes in the upper handlebar . The unit is shipped with the handlebar knobs in the lowest height setting holes . If this height is correct for you , simply tighten the two handlebar knobs . If desired , reposition the C handlebar knobs , mounting screws and washers in the other set of holes . 3 . Check the six ( 6 ) plastic ties ( C , Figure 1 ) . Ties must be positioned as shown . NOTE : There is only one handlebar storage position – folded over and down as originally shipped . Figure 1 5
Page: 6

Section Features and Controls 3 KNOW YOUR EQUIPMENT READ THIS OWNER’S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR EQUIPMENT . Know the location and function of all features and controls on the equipment . Save this manual for future reference . Handlebar Height Adjustment Knob ( B , Figure 2 ) WARNING Two height settings , plus a storage position are available . Refer to Assembly Steps , STEP 1 in Section 2 for adjustment Before operating your machine , carefully read and under - instructions . stand all safety , control , and operating instructions in this Manual , the separate Engine Owner’s Manual and on the Tilling Depth Adjustment Knob ( C , Figure 2 ) decals on the machine . Loosening the knob enables you to move the wheel bracket ( K ) Failure to follow these instructions can result in serious per - up or down on the height adjustment bar ( L ) . This controls the sonal injury . tilling depth . IMPORTANT : Do not move the wheel bracket any higher than the top of the adjustment bar . Adjustable Tine Patterns ( D , Figure 2 ) The four tine sections are arranged from the factory for max - imum performance under a wide variety of conditions . If needed , the tines can be arranged for narrower tilling or close H cultivating . The tines can also be arranged to till very stony A soil . See Adjusting Tine Positions in Section 4 for details . Carrying Handle ( E , Figure 2 ) When the handlebar is folded in the storage position the unit G can be carried by the carrying handle . The carrying handle J also serves as a tie - down anchor point . J Edger Attachment ( H , Figure 2 ) Use this separate attachment to create borders or edges along walks , driveways , flower beds , etc . See Section 4 for details on J installing and using this attachment . Engine Controls B J Fuel Primer Bulb ( Section 4 , Figure 4 ) E Use the Fuel Primer Bulb to help start the engine under certain F conditions . See Stopping and Starting the Engine in Section 4 J and the Engine Owner’s Manual for details . B J Engine Choke ( Section 4 , Figure 5 ) Use the Engine Choke lever to help start the engine . The posi - C tion of the lever is dependent on whether the engine is cold or warm . See Stopping and Starting the Engine in Section 4 and K the Engine Owner’s Manual for details . L Engine On / Off Switch ( A , Figure 2 ) Use the ON / OFF Switch to start or stop the engine . See Stop - ping and Starting the Engine in Section 4 for details . Engine Recoil Start Rope ( F , Figure 2 ) Use the recoil start rope to start the engine . See Stopping and Starting the Engine in Section 4 for details . D Throttle / Tines Control Lever ( G , Figure 2 ) Figure 2 : Features and controls . Use the Throttle / Tines Control Lever to start and stop tine rota - tion . This lever also varies tine speed . Release the lever to stop all tine motion . See Section 4 for more details on this control . 6
Page: 7

Section Operation 4 c . Retighten the depth adjustment WARNING knob . B Before operating the unit , carefully read 10 . Reconnect the spark plug wire . and understand all safety , control and operating instructions in this Manual , DANGER the separate Engine Owner’s Manual A and the decals on the machine . GASOLINE IS HIGHLY FLAMMABLE AND ITS VAPORS ARE EXPLOSIVE . Failure to follow these instructions can result in serious personal injury . Follow the gasoline safety rules in this Figure 4 : Primer bulb ( A ) and fuel - return Manual ( Section 1 ) and in the separate tube ( B ) . Engine Owner’s Manual . PRE - START PREPARATION Close Failure to follow gasoline safety instruc - Before starting the engine , perform the C tions can result in serious personal following checks and services : injury and property damage . 1 . Disconnect the spark plug wire from Open the spark plug . 11 . Add gasoline to the fuel tank . 2 . Move the engine On / Off switch to the OFF position . IMPORTANT : Read the separate Engine Figure 5 : Choke lever . Owner’s Manual before starting the 3 . Check that all wires and cables are engine . Never use stale or contaminated 1 . Move the On / Off Switch ( A , Figure 2 ) properly and securely connected . gasoline or oil / gas mix . The engine must to the ON position . 4 . Check the six plastic cable ties ( J , be stopped and cool before adding gas . 2 . To start a cold engine , move the choke Figure 2 ) . Be sure that cables and ties are Fill the fuel tank with unleaded gasoline lever ( C , Figure 5 ) to the CLOSED posi - positioned as shown . Cables must not be ( with a pump octane rating of 86 or tion . To restart a warm engine , leave the kinked or jammed in the handlebar . higher ) according to the directions in the choke lever in the OPEN position . 5 . Adjust handlebar height to desired po - separate Engine Owner’s Manual . The 3 . To start a cold engine , or after refueling sition ( see Section 2 ) . engine is a vertical type , GX 31 model . an engine that has run out of fuel , press 6 . Check hardware for tightness . the priming bulb ( A , Figure 4 ) repeatedly until fuel can be seen in the clear - plastic 7 . Check engine oil level ( see Engine STOPPING AND fuel - return tube ( B ) . To restart a warm Owner’s Manual ) . STARTING THE ENGINE engine , it is not necessary to press the 8 . Check the air filter ( see Engine Owner’s Stopping the Engine priming bulb . Manual ) . 4 . Move to the starting position ( Figure 9 . Adjust the tilling depth as follows : WARNING 6 ) , keeping your feet positioned safely a . Loosen tilling depth adjustment away from the tines . Do not squeeze the Throttle / Tines Con - knob ( A , Figure 3 ) . trol Lever while starting engine . 5 . Place one hand on the upper handlebar to stabilize the machine . Use the other Tines may propel the machine forward if hand to pull the recoil start rope lightly the engine speed is advanced from idle . A until you feel resistance , then pull briskly . Failure to comply can result in personal B Let the rope rewind slowly after each pull . injury or property damage . C NOTE : An alternate stabiliza - tion method is to stand in To stop the engine , move the On / Off the starting position Switch ( A , Figure 2 ) to the OFF position . ( Figure 6 ) , but place one hand on the carrying NOTE : The On / Off switch wire must be handle while pulling the securely connected at both ends . Check starter rope with the regularly to ensure that the switch wire is Figure 3 other hand . securely connected to the switch and the engine . b . Move wheel bracket ( B , Figure 3 ) up 6 . If the choke lever in relation to height adjustment bar was moved to the ( C ) . Moving bracket upward results Starting the Engine CLOSED position to in shallower tilling , which is recom - start the engine , grad - NOTE : Do not squeeze Engine mended for initial use . ually move it to the Throttle / Tines Control Lever ( G , Figure 2 ) OPEN position as the IMPORTANT : Do not move the wheel when starting engine . engine warms up . bracket any higher than the top of Figure 6 the adjustment bar . 7
Page: 8

Section 4 : Operation C B A Figure 7 : Tine patterns . Adjust engine speed to suit the tilling Narrow Tine Positions – For a narrow , TILLING AND CULTIVATING conditions . Remember that the rotating 4 - 1 / 2 " tilling width , remove the outside tines help to pull the machine forward . tine section on the left - and right - sides WARNING Use slower speeds and a shallow depth ( B , Figure 7 ) . See Tine Removal and In - setting when learning to use the unit and stallation in Section 5 for detailed informa - whenever you are tilling on hard , rough or tion on how to set up this tine position . uneven ground . Stony Soil Tine Positions – When tilling 5 . Do not try to till too deeply in the first deeply in stony soil , stones may become Keep away from rotating tines . Rotating pass through sod or very hard ground . If jammed between the inner tines and the tines will cause serious personal injury . the machine jumps or bucks , use a shal - machine hood . This setup swaps the two lower depth setting and reduce the engine inner tines to minimize jamming ( C , Use your machine for busting sod , speed . With each succeeding pass , till Figure 7 ) . See Tine Removal and Installa - preparing seedbeds and for cultivating in more deeply . tion in Section 5 for detailed information gardens and flower beds . It is easy to op - 6 . Apply downward pressure on the han - on how to set up this tine position . erate , but it is important that you start out dlebars for shallower tilling . Lift the han - slowly and read this Section thoroughly Tilling Patterns dlebars to dig more deeply . If the ma - before putting it to use . Let the machine 1 . To make seedbeds , go over the same chine stays and tills in one spot , try do most of the work . The tines will pull path twice in the first row , then overlap swinging the handlebars from side to side the machine forward , letting you adjust one - half the machine width on each suc - to start it moving forward again . forward speed by pressing down or lifting cessive pass until all rows are tilled twice 7 . For easier tilling , water very hard soil a the handlebars . ( D , Figure 8 ) . few days before tilling . Avoid working the 1 . Roll the machine to the work area . soil when soggy or wet . Wait a day or 2 . Adjust the tilling depth to the desired two after heavy rain for the ground to dry . position ( see Pre - Start Preparation on the previous page ) . Cultivating 1 . Cultivating is shallow tilling that dis - 3 . Start the engine ( see Stopping and rupts weeds and aerates the upper crust Starting the Engine on the previous of soil . page ) . Stand behind the handlebar and push down on the bar to raise the tines 2 . Do not till deeper than 1 " - 2 " to avoid D E off the ground . Squeeze the injuring nearby plant roots . Cultivate Figure 8 : Recommended Tilling Pattern . Throttle / Tines Lever – the engine should often , so that weeds do not grow large speed up and the tines start rotating . Re - and cause needless tangling in the tines . 2 . Make a second pass at a right angle lease the Throttle / Tines Lever to return to 3 . With careful planning , you can space across the original passes . Again , idle , the tines should stop rotating or they the seed rows far enough apart to allow overlap each pass ( E , Figure 8 ) . Hard may rotate very slowly . Lowering them sufficient room for the machine to culti - ground may take three to four passes back to the ground should stop any rota - vate after the plants have grown . before the desired depth is achieved . tion . NOTE : For small gardens , overlap by Adjusting Tine Positions NOTE : If tines continue to rotate when one - half ( 1 / 2 ) the machine width , fol - Depending upon the tilling project , you engine is idling , either the idle speed is lowed by successive passes at one - have a choice of three tine patterns : too high or the centrifugal clutch is mal - quarter ( 1 / 4 ) machine width . This over - functioning . If this occurs , contact the Wide ( Standard ) Tine Positions – As lapping method assures thorough tilling . Factory or your local authorized dealer . shipped from the factory , the unit is set up for general tilling and cultivating . This 4 . Squeeze the Throttle / Tines Lever to Making Border Edges 10 " wide tine pattern ( the maximum tilling start the tines rotating . Lower the tines to Use the Edger Attachment to make clean , width ) uses all four tine sections begin tilling . Firmly hold the handlebar to sharp edges next to walkways , driveways , ( A , Figure 7 ) . See Tine Removal and In - prevent the machine from moving for - paths , planted areas , patios , etc . See In - stallation in Section 5 for detailed informa - ward too quickly and to allow enough stalling and Using the Edger Attachment , tion on how to set up this tine position . time for the tines to dig deeply enough . in this Section , for detailed information . 8
Page: 9

Section 4 : Operation INSTALLING AND USING DETAIL E THE EDGER ATTACHMENT Ring Lock Pin This side out WARNING Contact with rotating tines or other C moving parts can cause serious per - sonal injury . Before installing or removing attach - ments , or adjusting or servicing the ma - Figure 9 : Ring lock pin and tines . chine , stop the engine , let all moving parts come to a complete stop , discon - D Keep left and right - side tines separate and nect the spark plug wire and move the marked for easier reinstallation . wire away from the spark plug . E IMPORTANT : The ring lock pin is under To create borders or edges near walks , spring tension – use care when removing driveways , flower beds , etc . , you must E or replacing the ring lock pin . B remove the four tine sections and install A 4 . It is important for proper tilling perfor - the Edger Attachment ( this attachment mance that the tine sections be later rein - was supplied with the unit – see Figure 10 : Border / Edger tine assembly . stalled in their original positions . There - Section 3 ) . fore , mark the position of each tine section Using the Edger Attachment Installing the Edger Attachment ( Left - Outer , Left - Inner , etc . ) before re - The Edger Attachment makes clean , sharp 1 . Gather together the following parts : moving them . Refer to Figure 7 for tine edges next to walkways , driveways , Border / Edger Tine ( A , Figure 10 ) ; Long position information . paths , planted areas , patios , etc . Bushing ( B ) ; Border / Edger Wheel ( C ) ; and 5 . Install the short bushing ( D , Figure 10 ) Short Bushing ( D ) . Take your time when onto the tine shaft . Then place the edging . Decide how far 2 . Prop the machine carefully onto the Border / Edger wheel ( C ) onto the same away to edge the walk or front of the tubular carrying handle . The shaft – the wheel hub should face toward drive , then slowly pro - work surface should be firm and flat . the tiller . Insert the ring lock pin through ceed using the walk or NOTE : Typically , the Border / Edger Tine is the rounded side of the tine shaft and drive as your sight line . mounted on the right side of the unit for snap the ring down over the shaft ( see right - handed people , and on the left - side “ DETAIL ” , Figure 10 ) . of the unit for left - handed people . 6 . Slide the long bushing ( B , Figure 10 ) 3 . Flip open and remove the two ring lock onto the opposite side shaft . Then install pins ( E , Figures 9 and 10 ) on each tine the Border / Edger tine ( A ) and secure it shaft . with the ring lock pin . Attachments The following Tiller / Edger attachments are available where the Tiller / Edger was purchased . See your local authorized dealer or con - tact the Factory for details . Lawn Aerator Attachment – Model OEM - 290 - 264 Power Lawn Rake Attachment – Model OEM - 290 - 263 The Lawn Aerator Attachment helps The Power Lawn Rake helps to keep to promote healthy , dense lawns your lawn healthy and vigorous . by loosening and aerating the Matted grass and debris looks soil for better root growth . unattractive and stifles lawn Four tempered steel tines growth and overall health . puncture the surface This attachment mounts of the lawn thus allowing without tools and features nutrients to reach the dozens of tempered steel roots more easily . This “ fingers ” that penetrate attachment assembles and loosen matted grass without tools . without disturbing root growth . An 18 " - wide swath covers a large lawn area quickly . 9
Page: 10

Section Maintenance 5 REQUIRED MAINTENANCE SCHEDULE WARNING REQUIRED MAINTENANCE Before First Every 3 Every 6 Yearly Every Before inspecting , cleaning or servicing Perform at every indicated month or Each month months months 2 years the machine , shut off engine , let all operating hour interval , whichever Use or 10 Hrs . or 25 Hrs . or 50 Hrs . moving parts come to a complete stop , comes first . * See Engine Owner’s Manual disconnect the spark plug wire and move for engine related maintenance . the wire away from the spark plug . Check Tightness of Bolts and Nuts x Failure to follow these instructions can ( 1 ) x Check Transmission Lubricant Level x result in personal injury or property damage . Clean Machine x Clean Tine Shaft x Engine Oil Level Check x EQUIPMENT MAINTENANCE Change x x Transmission Maintenance Air Cleaner Check x The transmission was lubricated at the ( 2 ) Change x factory and should not require any further Spark Plug Check / Clean x lubrication . Replace x However , you should check the lubricant level after the first five ( 5 ) hours of opera - Cooling Fins Check x tion and every twenty - five ( 25 ) operating Spark Arrester Clean x hours thereafter . If needed , use a high - Fuel Tank Clean x quality , automotive - grade petroleum - based grease . Fuel Filter Check x ( 3 ) Clutch Shoes Check x WARNING Idle Speed Check - Adjust x ( 3 ) Before tipping engine or equipment to Valve Clearance Check - Adjust x ( 3 ) service transmission , drain fuel from tank by running engine until fuel tank is Fuel Tubes Check Every 2 years ( Replace if necessary ) ( 3 ) empty . Allow engine to cool . * For commercial use , log hours of operation to determine proper maintenance intervals . ( 1 ) Check after first 5 hours of use . To check the transmission : ( 2 ) Service more frequently when used in dusty areas . ( 3 ) Item should be serviced by your servicing dealer , unless you have the proper tools and 1 . Stop the engine , let it cool and discon - are mechanically proficient . nect the spark plug wire . 2 . Place the machine down on its left side Lubricant should be visible in the top two Other Lubrication Points so the right end of the tine shaft faces up . holes ( B and C ) . If so , replace all three • Handlebar Adjustment Knobs : Spray plugs . If lubricant is needed , proceed as 3 . Remove the right - side tines ( see Tine occasionally with a silicone type lubri - follows . Removal and Installation in this Section ) . cant . 4 . Clean the transmission housing . • Throttle / Tines Control Lever Cable : To lubricate the transmission : Squeeze the lever closed and spray a lu - 5 . Remove the three threaded plugs ( A , B 1 . Place the nozzle ( D , Figure 11 ) of a bricant into the cable area . and C , Figure 11 ) from the transmission . standard grease gun firmly against the • Tine Shaft : After each use , remove the rim of the middle hole ( B ) and add grease tines , clean the tine shaft with sandpaper D until it begins to seep from the bottom and apply a light coat of oil to the tine hole ( A ) . Reinstall the plug in the bottom A shaft . hole ( A ) . Next apply grease to the top fill B C hole ( C ) until it begins to seep from the middle hole ( B ) . Reinstall the plugs in the Hardware / Electrical Connections middle ( B ) and top ( C ) holes . Before each use , check that all hardware is tight and that the On / Off Switch wire 2 . Before reinstalling the tines , use a fine connections are secure . Also check that grade sandpaper to clean any rust off the the switch wiring is in good condition . tine shaft . Apply a few drops of oil to the tine shaft to make future tine removal easier . Figure 11 : Transmission lubricant check and fill locations . 10
Page: 11

Section 5 : Maintenance WARNING Before inspecting , cleaning or servicing the machine , shut off engine , wait for moving parts to stop , dis - connect spark plug wire and move wire away from spark plug . Failure to follow these instructions can result in serious personal injury or property damage . ENGINE MAINTENANCE WARNING Avoid contact with the cutting edges on WARNING the tines . B The temperature of the muffler and adja - To avoid personal injury when removing o F cent engine areas may exceed 150 or installing tines , wear heavy work o C ) . Contact may cause burns . Avoid ( 65 gloves . The engine must be off , all these areas . Remove the spark plug moving parts stopped , and the spark lead and ground the lead to the engine to Figure 13 : Narrow tilling tine configuration . plug wire disconnected from the spark prevent accidental starts and fires . plug and moved away from the plug . Failure to do this could cause personal Arranging Tines for Stony Soil injury . 1 . Prop the machine forward so it rests Arranging Tines on the front of the tubular carrying • Maintain the correct engine oil level and for Narrow Tilling handle . The work surface should be flat change the oil as recommended ( more 1 . Prop the machine forward so it rests and firm . often in dusty conditions ) . on the front of the tubular carrying 2 . Remove the ring lock pin ( A , Figure 12 ) handle . The work surface should be flat • Keep the air filter clean . Operating the from both sides of the unit . Remove both and firm . engine with a dirty , clogged air filter can outer tine sections . Be sure to mark each cause poor performance and damage to 2 . Flip open the ring ( A , Figure 12 ) on the section as a left or right side tine and the engine . Never operate engine left side ring lock pin and remove the ring whether it is an inner or outer section . without air filter installed . lock pin . 3 . Remove the inner tine sections and • Keep the spark plug clean and properly IMPORTANT : The ring lock pin ( A , Figure swap their positions ( the inner right - side gapped . Replace every 2 years . 12 ) is under spring tension – use care section goes onto the left side of the ma - when removing or replacing the ring lock chine , and the inner left - side goes onto • The engine cooling fins must be kept pin . the right side of the machine ) . clean to prevent overheating of the engine . A WARNING Do not tamper with the engine governor screw which is factory - set for the proper engine speed . Overspeeding the engine beyond the factory high speed setting can be dangerous and will void the engine warranty . Authorized service shall be sought if a problem exists . • If the engine is equipped with a spark Figure 12 : Standard wide tine pattern and Figure 14 : Stony soil tine pattern . arrester , clean it every year . ring lock pin location . • Clean , check or adjust the following 4 . Reinstall the two outer tine sections items according to the instructions in 3 . Remove the outer tine section ( do not onto the sides from which they were re - the Engine Owner’s Manual : fuel tank , remove inner tine section ) and mark it as moved ( Figure 14 ) . fuel filter , clutch shoes , idle speed , valve to which side it is from ( left or right ) and 5 . Insert the ring lock pins through the clearance and fuel tubes . whether it’s an outer or inner tine section . rounded side of the tine shafts and snap 4 . Slide one of the long bushings ( B , the rings down over the shafts ( see TINE REMOVAL Figure 13 ) , provided with the unit , onto DETAIL - Ring Lock Pin , Figure 10 , in the shaft . Insert the ring lock pin through AND INSTALLATION Section 4 ) . the rounded side of the tine shaft and The tines wear with use and should be re - snap the ring down over the shaft ( see placed if tilling takes longer than usual or DETAIL - Ring Lock Pin , Figure 10 , in if the soil does not mix thoroughly . In ad - Section 4 ) . dition to the standard 10 " tilling width tine 5 . Repeat this procedure on the opposite pattern , the tines can be arranged in a 1 side . / 2 " tilling width pattern for narrow , 4 smaller areas , and a special pattern for stony soil conditions . 11
Page: 12

Section 5 : Maintenance WARNING Before inspecting , cleaning or servicing the machine , shut off engine , wait for moving parts to stop , dis - connect spark plug wire and move wire away from spark plug . Failure to follow these instructions can result in serious personal injury or property damage . Replacing Worn Tine Sections Off - Season Storage Procedure STORAGE The tines are excessively worn if tilling • Protect the engine and perform recom - WARNING takes much longer than before and soil is mended engine maintenance by fol - not being mixed thoroughly enough . • Never store your equipment when there lowing the engine storage instructions is fuel in the fuel tank . 1 . Prop the machine forward so it rests found in the separate Engine Owner’s on the front of the tubular carrying Manual . • Never place your equipment near any handle . The work surface should be flat source of sparks or open flame ( such NOTE : Be sure to protect the fuel lines , and firm . as from a hot water heater , a space carburetor and fuel tank from gum de - heater or clothes dryer ) . 2 . Remove the ring lock pin ( A , Figure 12 ) posits by removing the fuel or by from both sides of the unit . Remove the treating the fuel with a stabilizer . See Failure to comply can result in serious old tine sections and replace them with Engine Owner’s Manual for more infor - personal injury or property damage . new tine sections . Refer to Figure 12 and mation . the tine position shown in the Parts List • Remove tines . Clean all soil and debris IMPORTANT : It is important to prevent for tine positioning details . Insert the ring from dust covers and tine shaft . Lubri - gum deposits from forming in essential lock pins through the rounded side of the cate tine shaft with light oil . Replace fuel system parts such as carburetor , fuel tine shafts and snap the ring over the tines . filter , fuel hose , or tank during storage . shaft ( see DETAIL - Ring Lock Pin , Figure Also , experience indicates that alcohol - • Cover engine and store equipment in a 10 , in Section 4 ) . blended fuels ( called gasohol or using dry , sheltered location . ethanol or methanol ) can attract moisture which leads to separation and formation of acids during storage . Acidic gas can damage the fuel system of an engine while in storage . TROUBLESHOOTING Before performing any of the corrections in this Troubleshooting Chart , refer to the appropriate information contained in this Manual and the Engine Owner’s Manual for the correct safety precautions and servicing procedures . Contact your local authorized Engine Service Dealer for engine service . Contact your local authorized dealer for service problems with the machine . PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Engine does not start . 1 . Spark plug wire disconnected . 1 . Reconnect wire to spark plug . 2 . Out of gas . 2 . Check fuel tank . 3 . Stale gas . 3 . Drain old gas . Replace with fresh gas . 4 . Priming / Choking procedure not correct . 4 . Refer to Priming / Choking procedure and starting instructions in manual . 5 . Dirty air filter ( s ) . 5 . Clean or replace air filters . 6 . Worn , corroded or broken spark plug . 6 . Replace spark plug . 7 . On / Off Switch in OFF position . 7 . Move On / Off Switch to ON . Engine runs poorly or 1 . Fouled spark plug . 1 . Remove , inspect , clean spark plug . has low power under 2 . Dirty air filter ( s ) . 2 . Clean or replace dirty air filters . tilling conditions . 3 . Stale gas . 3 . Drain old fuel and replace with fresh fuel . 4 . Carburetor malfunction / fuel filter 4 . See authorized engine service dealer . clogged / ignition malfunction / valves stuck , etc . Engine overheats . 1 . Engine cooling system clogged . 1 . Remove debris . 2 . Carburetor out of adjustment . 2 . See an authorized engine dealer . Tines stop rotating . 1 . Object wedged between tines and hood . 1 . Remove wedged object . 2 . Internal transmission problem . 2 . See an authorized engine dealer . 12
Page: 13

Model 148H Parts List 2 13 7 19 23 5 21 A 18 A 6 18 B B A 9 22 24 3 B 1 10 4 A 13 A 8 14 , 15 20 3 16 , 17 5 21 24 22 14 , 15 21 11 , 12 Transmission Assembly Ref . # Part # Description Qty . Ref . # Part # Description Qty . 13 1110106 Locknut , Nyloc , 1 / 4 - 20 . . . . . . . . . . . . . . . . . 8 1 1915039 Transmission Case - left - side . ( Incl . pressed - in bushing ) . . . . . . . . . . . . 1 14 1983635 Thrust Washer , Output ( . 050 " ) . . . . . . . . . . . A / R 2 1915040 Transmission Case - right - side . 15 1983640 Thrust Washer , Output ( . 040 " ) . . . . . . . . . . . A / R ( Incl . pressed - in bushing ) . . . . . . . . . . . . 1 16 1983641 Thrust Washer , Input ( . 020 " ) . . . . . . . . . . . . A / R 3 1983632 Oil Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 17 1983642 Thrust Washer , Input ( . 035 " ) . . . . . . . . . . . . A / R 4 1918308 Worm Input Shaft Assembly . . . . . . . . . . . . 1 18 1983638 Thrust Washer . . . . . . . . . . . . . . . . . . . . . . . 2 5 1983731 Input Bearing . . . . . . . . . . . . . . . . . . . . . . . . 2 19 736 - 0463 Flat Washer , 1 / 4 . . . . . . . . . . . . . . . . . . . . . . 2 6 1983636 Thrust Bearing . . . . . . . . . . . . . . . . . . . . . . . 1 20 1983663 Hex Hd . Screw , 1 / 4 - 20 x 5 . . . . . . . . . . . . . . 2 7 1983637 Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . 1 21 1747166 Set Screw , 1 / 4 - 28 x 3 / 8 . . . . . . . . . . . . . . . . 4 8 1904416 Shaft Assembly . ( Incl . pressed - on worm 22 1915055 Dust Cover . . . . . . . . . . . . . . . . . . . . . . . . . . 2 gear and two ring lock pins ) . . . . . . . . . . . 1 23 1918052 Oil Seal , Input . . . . . . . . . . . . . . . . . . . . . . . . 1 9 1909923 Oil Seal , Input . . . . . . . . . . . . . . . . . . . . . . . . 1 24 1983713 Felt Washer . . . . . . . . . . . . . . . . . . . . . . . . . 2 10 1185741 Plug , 1 / 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 11 710 - 0206 Hex Screw , 1 / 4 - 20 x 7 / 8 ( five locations , identified as “ A ” on transmission case ) . . . 5 12 710 - 0597 Hex Screw , 1 / 4 - 20 x 1 ( three locations , identified as “ B ” on transmission case ) . . . 3 A / R – As Required 13
Page: 14

Parts List Model 148H 7 4 10 , 10A 9 11 42 5 SEE PREVIOUS PAGE 2 56 6 12 42 3 13 55 13 1 53 13 54 13 8 16 20 45 44 48 45 15 52 29 44 50 46 51 18 14 13 21 13 17 49 18 47 37 19 35 42 36 31 42 19 32 38 24 41 27 34 43 39 23 33 25 41 41 40 26 28 41 22 29 40 30 14
Page: 15

Model 148H Parts List Ref . # Part # Description Qty . Ref . # Part # Description Qty . 32 1909539 Inner Tine - Right - Hand Side . . . . . . . . . . . . . . . . . . . . . . . . 1 1 1918087 Handlebar Assy . ( Incl . Refs . 2 , 3 , 4 & 5 ) . . . . . . . 1 33 1909712 Outer Tine - Left - Hand Side . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 777I00008 Decal - On / Off Ignition Switch . . . . . . . . . . . . . . . . . . . . . . . 1 34 1909711 Inner Tine - Left - Hand Side . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3 777I00007 Decal - Starting Stabilization . . . . . . . . . . . . . . . . . . . . . . . . . 1 35 1909680 Wheel Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 4 777I00009 Decal - Throttle / Tines Control Lever Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 36 GW - 90077 Carriage Bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 5 1917451 Handlebar Grip , PVC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 37 1909835 Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 6 1917755 Throttle Lever and Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 38 710 - 0597 Hex Hd . Screw , 1 / 4 - 20 x 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 7 1750608 Pan Hd . Screw , # 10 - 16 x 1 - 1 / 2 . . . . . . . . . . . . . . . . . . . . . 1 39 1909517 Axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 8 1731025 Saddle Hd . Screw , 5 / 16 - 18 x 2 . . . . . . . . . . . . . . . . . . . . . 2 40 1917754 Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 9 1909775 Spacer , Throttle Lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 41 GW - 9532 E - Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 10 1983718 On / Off Ignition Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 42 1185590 Ring Lock Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 10A 1981012 Bracket - On / Off Ignition Switch . . . . . . . . . . . . . . . . . . 1 43 1981022 Tine Hood Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 11 1766503 Phillips Hd . Screw , # 12 - 24 . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 44 1763767 Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 12 1918051 Wire Assy . - On / Off Ignition Switch . . . . . . . . . . . . . . . 1 45 1177038 Lock Washer , 5 / 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 13 1763682 Plastic Wire Tie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 46 GW - 90041 Hex . Hd . Screw , M6 x 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 14 1917576 Lower Handlebar - Left - Side . . . . . . . . . . . . . . . . . . . . . . . . . 1 47 1186332 Hex Flange Screw , 5 / 16 - 18 x 1 - 1 / 4 . . . . . . . . . . . . . . . 4 15 1917575 Lower Handlebar - Right - Side . . . . . . . . . . . . . . . . . . . . . . . 1 48 1917530 Adapter Plate - Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 16 1909720 Foam Sleeve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 49 1917529 Adapter Plate - Transmission . . . . . . . . . . . . . . . . . . . . . . . . 1 17 1983663 Hex Hd . Screw , 1 / 4 - 20 x 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 50 1918365 Clutch Assy . ( Incl . Refs . 55 and 56 ) . . . . . . . . . . . . . . 1 18 710 - 0463 Flat Washer , 1 / 4 - 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 51 * * Hex Hd . Screw , M8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 19 1110106 Hex Locknut , 1 / 4 - 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 52 * * Flat Washer , M8 x M17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 20 * Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 21 1917531 Clutch Drum and Hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 EDGER ATTACHMENT 22 1918124 Tine Shield ( Incl . Refs . 23 , 24 , 25 & 26 ) . . . . . . . 1 53 1903777 Edger Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 23 777D06104 Decal - Logo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 54 1903778 Bushing - Short . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 24 777S00012 Decal - Warning , Rotating TInes . . . . . . . . . . . . . . . . . . . 1 55 1983648 Bushing - Long . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 25 777S30647 Decal - Warning , Hot Surfaces . . . . . . . . . . . . . . . . . . . . . . 1 56 1915054 Edger Tine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 26 777S00013 Decal - Caution , Operation Hazards . . . . . . . . . . . . . . 1 27 1186292 Hex Hd . Screw , # 10 - 24 x 1 / 2 . . . . . . . . . . . . . . . . . . . . . . . . 2 OPTIONAL ATTACHMENTS 28 1186387 Flange Locknut , # 10 - 24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 OEM - 290 - 263 Power Lawn Rake Attachment . . . . . . . . . . . . . . . . . . . . . . 1 29 736 - 0329 Lock Washer , 1 / 4 - 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 OEM - 290 - 264 Lawn Aerator Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 30 710 - 0501 Hex Cap Screw , 1 / 4 - 20 x 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 31 1909540 Outer Tine - Right - Hand Side . . . . . . . . . . . . . . . . . . . . . . . . 1 * Order parts from your local authorized engine dealer . Refer to engine nameplate for model / type number . * * Not available separately . SAFETY AND OPERATING DECALS Decals are not shown at full size . See above Parts List for reordering information . 1918221 . A ( 1 / 00 ) ON WARNING Hot surfaces can cause severe burns . A Rev Do not touch On top of handlebar 1904549 muffler or adjacent areas . On rear , left - WARNING side tine shield OFF On right - side handlebar On rear , right - side On top , left - side On right - side handlebar 15 tine shield tine shield
Page: 16

MANUFACTURER’S LIMITED WARRANTY FOR : The limited warranty set forth below is given by Troy - Bilt LLC with d . Troy - Bilt LLC does not extend any warranty for products respect to new merchandise purchased and used in the United sold or exported outside of the United States , its pos - States , its possessions and territories . sessions and territories , except those sold through Troy - Bilt LLC’s authorized channels of export distribution . Troy - Bilt LLC warrants this product against defects for a period of e . Parts that are not genuine Troy - Bilt parts are not covered by two ( 2 ) years commencing on the date of original purchase and this warranty . will , at its option , repair or replace , free of charge , any part found f . Service completed by someone other than an authorized to be defective in materials or workmanship . This limited war - service dealer is not covered by this warranty . ranty shall only apply if this product has been operated and main - g . Transportation charges and service calls are not covered . tained in accordance with the Operator’s Manual furnished with No implied warranty , including any implied warranty of mer - the product , and has not been subject to misuse , abuse , com - chantability of fitness for a particular purpose , applies after mercial use , neglect , accident , improper maintenance , alteration , the applicable period of express written warranty above as vandalism , theft , fire , water , or damage because of other peril or to the parts as identified . No other express warranty , natural disaster . Damage resulting from the installation or use of whether written or oral , except as mentioned above , given any accessory or attachment not approved by Troy - Bilt LLC for by any person or entity , including a dealer or retailer , with re - use with the product ( s ) covered by this manual will void your war - spect to any product , shall bind Troy - Bilt LLC . During the ranty as to any resulting damage . period of the warranty , the exclusive remedy is repair or re - placement of the product as set forth above . Normal wear parts or components thereof are subject to sepa - rate terms as follows : All normal wear parts or component fail - The provisions as set forth in this warranty provide the sole ures will be covered on the product for a period of 90 days re - and exclusive remedy arising from the sale . Troy - Bilt LLC gardless of cause . After 90 days , but within the two year period , shall not be liable for incidental or consequential loss or normal wear part failures will be covered ONLY IF caused by de - damage including , without limitation , expenses incurred for fects in materials or workmanship of OTHER component parts . substitute or replacement lawn care services or for rental Normal wear parts and components include , but are not limited expenses to temporarily replace a warranted product . to : batteries , belts , blades , blade adapters , grass bags , rider deck wheels , seats , snow thrower skid shoes , shave plates , Some states do not allow the exclusion or limitation of incidental auger spiral rubber , tires . or consequential damages , or limitations on how long an implied HOW TO OBTAIN SERVICE : Warranty service is available , warranty lasts , so the above exclusions or limitations may not WITH PROOF OF PURCHASE , through your local authorized apply to you . service dealer . To locate the dealer in your area , check your Yellow Pages , or contact Troy - Bilt LLC at P.O . Box 361131 , In no event shall recovery of any kind be greater than the amount Alteration of the Cleveland , Ohio 44136 - 0019 , 1 - 866 - 840 - 6483 , or log on to our of the purchase price of the product sold . You safety features of the product shall void this warranty . Web site at www.troybilt.com . assume the risk and liability for loss , damage , or injury to you and your property and / or to others and their property arising out of This limited warranty does not provide coverage in the following the misuse or inability to use the product . cases : a . The engine or component parts thereof . These items This limited warranty shall not extend to anyone other than the carry a separate manufacturer’s warranty . Refer to the original purchaser or to the person for whom it was purchased as applicable manufacturer’s warranty for terms and cond a gift . tions . b . Log splitter pumps , valves , and cylinders have a separate HOW STATE LAW RELATES TO THIS WARRANTY : This lim - one year warranty . ited warranty gives you specific legal rights , and you may c . Routine maintenance items such as lubricants , filters , also have other rights which vary from state to state . blade sharpening , tune - ups , brake adjustments , clutch adjustments , deck adjustments , and normal deterioration of the exterior finish due to use or exposure . TROY - BILT LLC , P.O . BOX 361131 , CLEVELAND , OHIO 44136 - 0019 , 1 - 866 - 840 - 6483
Search in Tiller - Cultivator on ebay
"